board/freescale/ls2080a/ddr.c

   1 /*
   2  * Copyright 2014 Freescale Semiconductor, Inc.
   3  *
   4  * SPDX-License-Identifier:     GPL-2.0+
   5  */
   6
   7 #include <common.h>
   8 #include <fsl_ddr_sdram.h>
   9 #include <fsl_ddr_dimm_params.h>
  10 #include "ddr.h"
  11
  12 DECLARE_GLOBAL_DATA_PTR;
  13
  14 void fsl_ddr_board_options(memctl_options_t *popts,
  15                                 dimm_params_t *pdimm,
  16                                 unsigned int ctrl_num)
  17 {
  18         const struct board_specific_parameters *pbsp, *pbsp_highest = NULL;
  19         ulong ddr_freq;
  20
  21         if (ctrl_num > 3) {
  22                 printf("Not supported controller number %d\n", ctrl_num);
  23                 return;
  24         }
  25         if (!pdimm->n_ranks)
  26                 return;
  27
  28         /*
  29          * we use identical timing for all slots. If needed, change the code
  30          * to  pbsp = rdimms[ctrl_num] or pbsp = udimms[ctrl_num];
  31          */
  32         if (popts->registered_dimm_en)
  33                 pbsp = rdimms[ctrl_num];
  34         else
  35                 pbsp = udimms[ctrl_num];
  36
  37
  38         /* Get clk_adjust, wrlvl_start, wrlvl_ctl, according to the board ddr
  39          * freqency and n_banks specified in board_specific_parameters table.
  40          */
  41         ddr_freq = get_ddr_freq(0) / 1000000;
  42         while (pbsp->datarate_mhz_high) {
  43                 if (pbsp->n_ranks == pdimm->n_ranks &&
  44                     (pdimm->rank_density >> 30) >= pbsp->rank_gb) {
  45                         if (ddr_freq <= pbsp->datarate_mhz_high) {
  46                                 popts->clk_adjust = pbsp->clk_adjust;
  47                                 popts->wrlvl_start = pbsp->wrlvl_start;
  48                                 popts->wrlvl_ctl_2 = pbsp->wrlvl_ctl_2;
  49                                 popts->wrlvl_ctl_3 = pbsp->wrlvl_ctl_3;
  50                                 goto found;
  51                         }
  52                         pbsp_highest = pbsp;
  53                 }
  54                 pbsp++;
  55         }
  56
  57         if (pbsp_highest) {
  58                 printf("Error: board specific timing not found for data rate %lu MT/s\n"
  59                         "Trying to use the highest speed (%u) parameters\n",
  60                         ddr_freq, pbsp_highest->datarate_mhz_high);
  61                 popts->clk_adjust = pbsp_highest->clk_adjust;
  62                 popts->wrlvl_start = pbsp_highest->wrlvl_start;
  63                 popts->wrlvl_ctl_2 = pbsp->wrlvl_ctl_2;
  64                 popts->wrlvl_ctl_3 = pbsp->wrlvl_ctl_3;
  65         } else {
  66                 panic("DIMM is not supported by this board");
  67         }
  68 found:
  69         debug("Found timing match: n_ranks %d, data rate %d, rank_gb %d\n"
  70                 "\tclk_adjust %d, wrlvl_start %d, wrlvl_ctrl_2 0x%x, wrlvl_ctrl_3 0x%x\n",
  71                 pbsp->n_ranks, pbsp->datarate_mhz_high, pbsp->rank_gb,
  72                 pbsp->clk_adjust, pbsp->wrlvl_start, pbsp->wrlvl_ctl_2,
  73                 pbsp->wrlvl_ctl_3);
  74 #ifdef CONFIG_SYS_FSL_HAS_DP_DDR
  75         if (ctrl_num == CONFIG_DP_DDR_CTRL) {
  76                 /* force DDR bus width to 32 bits */
  77                 popts->data_bus_width = 1;
  78                 popts->otf_burst_chop_en = 0;
  79                 popts->burst_length = DDR_BL8;
  80                 popts->bstopre = 0;     /* enable auto precharge */
  81         }
  82 #endif
  83         /*
  84          * Factors to consider for half-strength driver enable:
  85          *      - number of DIMMs installed
  86          */
  87         popts->half_strength_driver_enable = 1;
  88         /*
  89          * Write leveling override
  90          */
  91         popts->wrlvl_override = 1;
  92         popts->wrlvl_sample = 0xf;
  93
  94         /*
  95          * Rtt and Rtt_WR override
  96          */
  97         popts->rtt_override = 0;
  98
  99         /* Enable ZQ calibration */
 100         popts->zq_en = 1;
 101
 102 #ifdef CONFIG_SYS_FSL_DDR4
 103         popts->ddr_cdr1 = DDR_CDR1_DHC_EN | DDR_CDR1_ODT(DDR_CDR_ODT_80ohm);
 104         popts->ddr_cdr2 = DDR_CDR2_ODT(DDR_CDR_ODT_80ohm) |
 105                           DDR_CDR2_VREF_OVRD(70);       /* Vref = 70% */
 106 #else
 107         /* DHC_EN =1, ODT = 75 Ohm */
 108         popts->ddr_cdr1 = DDR_CDR1_DHC_EN | DDR_CDR1_ODT(DDR_CDR_ODT_75ohm);
 109         popts->ddr_cdr2 = DDR_CDR2_ODT(DDR_CDR_ODT_75ohm);
 110 #endif
 111 }
 112
 113 #ifdef CONFIG_SYS_DDR_RAW_TIMING
 114 dimm_params_t ddr_raw_timing = {
 115         .n_ranks = 2,
 116         .rank_density = 1073741824u,
 117         .capacity = 2147483648,
 118         .primary_sdram_width = 64,
 119         .ec_sdram_width = 0,
 120         .registered_dimm = 0,
 121         .mirrored_dimm = 0,
 122         .n_row_addr = 14,
 123         .n_col_addr = 10,
 124         .n_banks_per_sdram_device = 8,
 125         .edc_config = 0,
 126         .burst_lengths_bitmask = 0x0c,
 127
 128         .tckmin_x_ps = 937,
 129         .caslat_x = 0x6FC << 4,  /* 14,13,11,10,9,8,7,6 */
 130         .taa_ps = 13090,
 131         .twr_ps = 15000,
 132         .trcd_ps = 13090,
 133         .trrd_ps = 5000,
 134         .trp_ps = 13090,
 135         .tras_ps = 33000,
 136         .trc_ps = 46090,
 137         .trfc_ps = 160000,
 138         .twtr_ps = 7500,
 139         .trtp_ps = 7500,
 140         .refresh_rate_ps = 7800000,
 141         .tfaw_ps = 25000,
 142 };
 143
 144 int fsl_ddr_get_dimm_params(dimm_params_t *pdimm,
 145                 unsigned int controller_number,
 146                 unsigned int dimm_number)
 147 {
 148         const char dimm_model[] = "Fixed DDR on board";
 149
 150         if (((controller_number == 0) && (dimm_number == 0)) ||
 151             ((controller_number == 1) && (dimm_number == 0))) {
 152                 memcpy(pdimm, &ddr_raw_timing, sizeof(dimm_params_t));
 153                 memset(pdimm->mpart, 0, sizeof(pdimm->mpart));
 154                 memcpy(pdimm->mpart, dimm_model, sizeof(dimm_model) - 1);
 155         }
 156
 157         return 0;
 158 }
 159 #endif
 160 phys_size_t initdram(int board_type)
 161 {
 162         phys_size_t dram_size;
 163
 164         puts("Initializing DDR....");
 165
 166         puts("using SPD\n");
 167         dram_size = fsl_ddr_sdram();
 168
 169         return dram_size;
 170 }
 171
 172 void dram_init_banksize(void)
 173 {
 174 #ifdef CONFIG_SYS_DP_DDR_BASE_PHY
 175         phys_size_t dp_ddr_size;
 176 #endif
 177
 178         /*
 179          * gd->secure_ram tracks the location of secure memory.
 180          * It was set as if the memory starts from 0.
 181          * The address needs to add the offset of its bank.
 182          */
 183         gd->bd->bi_dram[0].start = CONFIG_SYS_SDRAM_BASE;
 184         if (gd->ram_size > CONFIG_SYS_LS2_DDR_BLOCK1_SIZE) {
 185                 gd->bd->bi_dram[0].size = CONFIG_SYS_LS2_DDR_BLOCK1_SIZE;
 186                 gd->bd->bi_dram[1].start = CONFIG_SYS_DDR_BLOCK2_BASE;
 187                 gd->bd->bi_dram[1].size = gd->ram_size -
 188                                           CONFIG_SYS_LS2_DDR_BLOCK1_SIZE;
 189 #ifdef CONFIG_SYS_MEM_RESERVE_SECURE
 190                 gd->secure_ram = gd->bd->bi_dram[1].start +
 191                                  gd->secure_ram -
 192                                  CONFIG_SYS_LS2_DDR_BLOCK1_SIZE;
 193                 gd->secure_ram |= MEM_RESERVE_SECURE_MAINTAINED;
 194 #endif
 195         } else {
 196                 gd->bd->bi_dram[0].size = gd->ram_size;
 197 #ifdef CONFIG_SYS_MEM_RESERVE_SECURE
 198                 gd->secure_ram = gd->bd->bi_dram[0].start + gd->secure_ram;
 199                 gd->secure_ram |= MEM_RESERVE_SECURE_MAINTAINED;
 200 #endif
 201         }
 202
 203 #ifdef CONFIG_SYS_DP_DDR_BASE_PHY
 204         /* initialize DP-DDR here */
 205         puts("DP-DDR:  ");
 206         /*
 207          * DDR controller use 0 as the base address for binding.
 208          * It is mapped to CONFIG_SYS_DP_DDR_BASE for core to access.
 209          */
 210         dp_ddr_size = fsl_other_ddr_sdram(CONFIG_SYS_DP_DDR_BASE_PHY,
 211                                           CONFIG_DP_DDR_CTRL,
 212                                           CONFIG_DP_DDR_NUM_CTRLS,
 213                                           CONFIG_DP_DDR_DIMM_SLOTS_PER_CTLR,
 214                                           NULL, NULL, NULL);
 215         if (dp_ddr_size) {
 216                 gd->bd->bi_dram[2].start = CONFIG_SYS_DP_DDR_BASE;
 217                 gd->bd->bi_dram[2].size = dp_ddr_size;
 218         } else {
 219                 puts("Not detected");
 220         }
 221 #endif
 222 }