board/freescale/ls1088a/ddr.c

   1 // SPDX-License-Identifier: GPL-2.0+
   2 /*
   3  * Copyright 2017 NXP
   4  */
   5
   6 #include <common.h>
   7 #include <fsl_ddr_sdram.h>
   8 #include <fsl_ddr_dimm_params.h>
   9 #include <log.h>
  10 #include <asm/arch/soc.h>
  11 #include <asm/arch/clock.h>
  12 #include <asm/global_data.h>
  13 #include "ddr.h"
  14
  15 DECLARE_GLOBAL_DATA_PTR;
  16
  17 #if defined(CONFIG_VID) && (!defined(CONFIG_SPL) || defined(CONFIG_SPL_BUILD))
  18 static void fsl_ddr_setup_0v9_volt(memctl_options_t *popts)
  19 {
  20         int vdd;
  21
  22         vdd = get_core_volt_from_fuse();
  23         /* Nothing to do for silicons doesn't support VID */
  24         if (vdd < 0)
  25                 return;
  26
  27         if (vdd == 900) {
  28                 popts->ddr_cdr1 |= DDR_CDR1_V0PT9_EN;
  29                 debug("VID: configure DDR to support 900 mV\n");
  30         }
  31 }
  32 #endif
  33
  34 void fsl_ddr_board_options(memctl_options_t *popts,
  35                            dimm_params_t *pdimm,
  36                            unsigned int ctrl_num)
  37 {
  38         const struct board_specific_parameters *pbsp, *pbsp_highest = NULL;
  39         ulong ddr_freq;
  40
  41         if (ctrl_num > 1) {
  42                 printf("Not supported controller number %d\n", ctrl_num);
  43                 return;
  44         }
  45         if (!pdimm->n_ranks)
  46                 return;
  47
  48         /*
  49          * we use identical timing for all slots. If needed, change the code
  50          * to  pbsp = rdimms[ctrl_num] or pbsp = udimms[ctrl_num];
  51          */
  52         pbsp = udimms[0];
  53
  54         /* Get clk_adjust, wrlvl_start, wrlvl_ctl, according to the board ddr
  55          * freqency and n_banks specified in board_specific_parameters table.
  56          */
  57         ddr_freq = get_ddr_freq(0) / 1000000;
  58         while (pbsp->datarate_mhz_high) {
  59                 if (pbsp->n_ranks == pdimm->n_ranks) {
  60                         if (ddr_freq <= pbsp->datarate_mhz_high) {
  61                                 popts->clk_adjust = pbsp->clk_adjust;
  62                                 popts->wrlvl_start = pbsp->wrlvl_start;
  63                                 popts->wrlvl_ctl_2 = pbsp->wrlvl_ctl_2;
  64                                 popts->wrlvl_ctl_3 = pbsp->wrlvl_ctl_3;
  65                                 goto found;
  66                         }
  67                         pbsp_highest = pbsp;
  68                 }
  69                 pbsp++;
  70         }
  71
  72         if (pbsp_highest) {
  73                 printf("Error: board specific timing not found for %lu MT/s\n",
  74                        ddr_freq);
  75                 printf("Trying to use the highest speed (%u) parameters\n",
  76                        pbsp_highest->datarate_mhz_high);
  77                 popts->clk_adjust = pbsp_highest->clk_adjust;
  78                 popts->wrlvl_start = pbsp_highest->wrlvl_start;
  79                 popts->wrlvl_ctl_2 = pbsp->wrlvl_ctl_2;
  80                 popts->wrlvl_ctl_3 = pbsp->wrlvl_ctl_3;
  81         } else {
  82                 panic("DIMM is not supported by this board");
  83         }
  84 found:
  85         debug("Found timing match: n_ranks %d, data rate %d, rank_gb %d\n"
  86                 "\tclk_adjust %d, wrlvl_start %d, wrlvl_ctrl_2 0x%x, wrlvl_ctrl_3 0x%x\n",
  87                 pbsp->n_ranks, pbsp->datarate_mhz_high, pbsp->rank_gb,
  88                 pbsp->clk_adjust, pbsp->wrlvl_start, pbsp->wrlvl_ctl_2,
  89                 pbsp->wrlvl_ctl_3);
  90
  91
  92
  93         popts->half_strength_driver_enable = 0;
  94         /*
  95          * Write leveling override
  96          */
  97         popts->wrlvl_override = 1;
  98         popts->wrlvl_sample = 0xf;
  99
 100
 101         /* Enable ZQ calibration */
 102         popts->zq_en = 1;
 103
 104         /* Enable DDR hashing */
 105         popts->addr_hash = 1;
 106
 107         popts->ddr_cdr1 = DDR_CDR1_DHC_EN | DDR_CDR1_ODT(DDR_CDR_ODT_60ohm);
 108 #if defined(CONFIG_VID) && (!defined(CONFIG_SPL) || defined(CONFIG_SPL_BUILD))
 109         fsl_ddr_setup_0v9_volt(popts);
 110 #endif
 111
 112         popts->ddr_cdr2 = DDR_CDR2_ODT(DDR_CDR_ODT_60ohm) |
 113                           DDR_CDR2_VREF_TRAIN_EN | DDR_CDR2_VREF_RANGE_2;
 114 }
 115
 116 #ifdef CONFIG_TFABOOT
 117 int fsl_initdram(void)
 118 {
 119         gd->ram_size = tfa_get_dram_size();
 120
 121         if (!gd->ram_size)
 122                 gd->ram_size = fsl_ddr_sdram_size();
 123
 124         return 0;
 125 }
 126 #else
 127 int fsl_initdram(void)
 128 {
 129         puts("Initializing DDR....using SPD\n");
 130
 131 #if defined(CONFIG_SPL) && !defined(CONFIG_SPL_BUILD)
 132         gd->ram_size = fsl_ddr_sdram_size();
 133 #else
 134         gd->ram_size = fsl_ddr_sdram();
 135 #endif
 136         return 0;
 137 }
 138 #endif /* CONFIG_TFABOOT */