board/freescale/ls1021aqds/ddr.c

   1 /*
   2  * Copyright 2014 Freescale Semiconductor, Inc.
   3  *
   4  * SPDX-License-Identifier:     GPL-2.0+
   5  */
   6
   7 #include <common.h>
   8 #include <fsl_ddr_sdram.h>
   9 #include <fsl_ddr_dimm_params.h>
  10 #include <asm/io.h>
  11 #include <asm/arch/clock.h>
  12 #include "ddr.h"
  13
  14 DECLARE_GLOBAL_DATA_PTR;
  15
  16 void fsl_ddr_board_options(memctl_options_t *popts,
  17                            dimm_params_t *pdimm,
  18                            unsigned int ctrl_num)
  19 {
  20         const struct board_specific_parameters *pbsp, *pbsp_highest = NULL;
  21         ulong ddr_freq;
  22
  23         if (ctrl_num > 3) {
  24                 printf("Not supported controller number %d\n", ctrl_num);
  25                 return;
  26         }
  27         if (!pdimm->n_ranks)
  28                 return;
  29
  30         pbsp = udimms[0];
  31
  32         /* Get clk_adjust, wrlvl_start, wrlvl_ctl, according to the board ddr
  33          * freqency and n_banks specified in board_specific_parameters table.
  34          */
  35         ddr_freq = get_ddr_freq(0) / 1000000;
  36         while (pbsp->datarate_mhz_high) {
  37                 if (pbsp->n_ranks == pdimm->n_ranks) {
  38                         if (ddr_freq <= pbsp->datarate_mhz_high) {
  39                                 popts->clk_adjust = pbsp->clk_adjust;
  40                                 popts->wrlvl_start = pbsp->wrlvl_start;
  41                                 popts->wrlvl_ctl_2 = pbsp->wrlvl_ctl_2;
  42                                 popts->wrlvl_ctl_3 = pbsp->wrlvl_ctl_3;
  43                                 popts->cpo_override = pbsp->cpo_override;
  44                                 popts->write_data_delay =
  45                                         pbsp->write_data_delay;
  46                                 goto found;
  47                         }
  48                         pbsp_highest = pbsp;
  49                 }
  50                 pbsp++;
  51         }
  52
  53         if (pbsp_highest) {
  54                 printf("Error: board specific timing not found for %lu MT/s\n",
  55                        ddr_freq);
  56                 printf("Trying to use the highest speed (%u) parameters\n",
  57                        pbsp_highest->datarate_mhz_high);
  58                 popts->clk_adjust = pbsp_highest->clk_adjust;
  59                 popts->wrlvl_start = pbsp_highest->wrlvl_start;
  60                 popts->wrlvl_ctl_2 = pbsp->wrlvl_ctl_2;
  61                 popts->wrlvl_ctl_3 = pbsp->wrlvl_ctl_3;
  62         } else {
  63                 panic("DIMM is not supported by this board");
  64         }
  65 found:
  66         debug("Found timing match: n_ranks %d, data rate %d, rank_gb %d\n",
  67               pbsp->n_ranks, pbsp->datarate_mhz_high, pbsp->rank_gb);
  68
  69         /* force DDR bus width to 32 bits */
  70         popts->data_bus_width = 1;
  71         popts->otf_burst_chop_en = 0;
  72         popts->burst_length = DDR_BL8;
  73
  74         /*
  75          * Factors to consider for half-strength driver enable:
  76          *      - number of DIMMs installed
  77          */
  78         popts->half_strength_driver_enable = 1;
  79         /*
  80          * Write leveling override
  81          */
  82         popts->wrlvl_override = 1;
  83         popts->wrlvl_sample = 0xf;
  84
  85         /*
  86          * Rtt and Rtt_WR override
  87          */
  88         popts->rtt_override = 0;
  89
  90         /* Enable ZQ calibration */
  91         popts->zq_en = 1;
  92
  93 #ifdef CONFIG_SYS_FSL_DDR4
  94         popts->ddr_cdr1 = DDR_CDR1_DHC_EN | DDR_CDR1_ODT(DDR_CDR_ODT_80ohm);
  95         popts->ddr_cdr2 = DDR_CDR2_ODT(DDR_CDR_ODT_80ohm) |
  96                           DDR_CDR2_VREF_OVRD(70);       /* Vref = 70% */
  97 #else
  98         popts->cswl_override = DDR_CSWL_CS0;
  99
 100         /* optimize cpo for erratum A-009942 */
 101         popts->cpo_sample = 0x58;
 102
 103         /* DHC_EN =1, ODT = 75 Ohm */
 104         popts->ddr_cdr1 = DDR_CDR1_DHC_EN | DDR_CDR1_ODT(DDR_CDR_ODT_75ohm);
 105         popts->ddr_cdr2 = DDR_CDR2_ODT(DDR_CDR_ODT_75ohm);
 106 #endif
 107 }
 108
 109 #ifdef CONFIG_SYS_DDR_RAW_TIMING
 110 dimm_params_t ddr_raw_timing = {
 111         .n_ranks = 1,
 112         .rank_density = 1073741824u,
 113         .capacity = 1073741824u,
 114         .primary_sdram_width = 32,
 115         .ec_sdram_width = 0,
 116         .registered_dimm = 0,
 117         .mirrored_dimm = 0,
 118         .n_row_addr = 15,
 119         .n_col_addr = 10,
 120         .n_banks_per_sdram_device = 8,
 121         .edc_config = 0,
 122         .burst_lengths_bitmask = 0x0c,
 123
 124         .tckmin_x_ps = 1071,
 125         .caslat_x = 0xfe << 4,  /* 5,6,7,8 */
 126         .taa_ps = 13125,
 127         .twr_ps = 15000,
 128         .trcd_ps = 13125,
 129         .trrd_ps = 7500,
 130         .trp_ps = 13125,
 131         .tras_ps = 37500,
 132         .trc_ps = 50625,
 133         .trfc_ps = 160000,
 134         .twtr_ps = 7500,
 135         .trtp_ps = 7500,
 136         .refresh_rate_ps = 7800000,
 137         .tfaw_ps = 37500,
 138 };
 139
 140 int fsl_ddr_get_dimm_params(dimm_params_t *pdimm,
 141                             unsigned int controller_number,
 142                             unsigned int dimm_number)
 143 {
 144         static const char dimm_model[] = "Fixed DDR on board";
 145
 146         if (((controller_number == 0) && (dimm_number == 0)) ||
 147             ((controller_number == 1) && (dimm_number == 0))) {
 148                 memcpy(pdimm, &ddr_raw_timing, sizeof(dimm_params_t));
 149                 memset(pdimm->mpart, 0, sizeof(pdimm->mpart));
 150                 memcpy(pdimm->mpart, dimm_model, sizeof(dimm_model) - 1);
 151         }
 152
 153         return 0;
 154 }
 155 #endif
 156
 157 #if defined(CONFIG_DEEP_SLEEP)
 158 void board_mem_sleep_setup(void)
 159 {
 160         void __iomem *qixis_base = (void *)QIXIS_BASE;
 161
 162         /* does not provide HW signals for power management */
 163         clrbits_8(qixis_base + 0x21, 0x2);
 164         udelay(1);
 165 }
 166 #endif
 167
 168 int fsl_initdram(void)
 169 {
 170         phys_size_t dram_size;
 171
 172 #if defined(CONFIG_SPL_BUILD) || !defined(CONFIG_SPL)
 173         puts("Initializing DDR....using SPD\n");
 174         dram_size = fsl_ddr_sdram();
 175 #else
 176         dram_size =  fsl_ddr_sdram_size();
 177 #endif
 178
 179 #if defined(CONFIG_DEEP_SLEEP) && !defined(CONFIG_SPL_BUILD)
 180         fsl_dp_resume();
 181 #endif
 182
 183         gd->ram_size = dram_size;
 184
 185         return 0;
 186 }
 187
 188 int dram_init_banksize(void)
 189 {
 190         gd->bd->bi_dram[0].start = CONFIG_SYS_SDRAM_BASE;
 191         gd->bd->bi_dram[0].size = gd->ram_size;
 192
 193         return 0;
 194 }