1 // SPDX-License-Identifier: GPL-2.0+
3 * Copyright 2009-2011 Freescale Semiconductor, Inc.
4 * Author: Srikanth Srinivasan <srikanth.srinivasan@freescale.com>
8 * This file handles the board muxing between the Fman Ethernet MACs and
9 * the RGMII/SGMII/XGMII PHYs on a Freescale P5040 "Super Hydra" reference
10 * board. The RGMII PHYs are the two on-board 1Gb ports. The SGMII PHYs are
11 * provided by the standard Freescale four-port SGMII riser card. The 10Gb
12 * XGMII PHYs are provided via the XAUI riser card. The P5040 has 2 FMans
13 * and 5 1G interfaces and 10G interface per FMan. Based on the options in
14 * the RCW, we could have upto 3 SGMII cards and 1 XAUI card at a time.
16 * Muxing is handled via the PIXIS BRDCFG1 register. The EMI1 bits control
17 * muxing among the RGMII PHYs and the SGMII PHYs. The value for RGMII is
18 * always the same (0). The value for SGMII depends on which slot the riser is
19 * inserted in. The EMI2 bits control muxing for the the XGMII. Like SGMII,
20 * the value is based on which slot the XAUI is inserted in.
22 * The SERDES configuration is used to determine where the SGMII and XAUI cards
23 * exist, and also which Fman's MACs are routed to which PHYs. So for a given
24 * Fman MAC, there is one and only PHY it connects to. MACs cannot be routed
25 * to PHYs dynamically.
28 * This file also updates the device tree in three ways:
30 * 1) The status of each virtual MDIO node that is referenced by an Ethernet
31 * node is set to "okay".
33 * 2) The phy-handle property of each active Ethernet MAC node is set to the
34 * appropriate PHY node.
36 * 3) The "mux value" for each virtual MDIO node is set to the correct value,
37 * if necessary. Some virtual MDIO nodes do not have configurable mux
38 * values, so those values are hard-coded in the DTS. On the HYDRA board,
39 * the virtual MDIO node for the SGMII card needs to be updated.
41 * For all this to work, the device tree needs to have the following:
43 * 1) An alias for each PHY node that an Ethernet node could be routed to.
45 * 2) An alias for each real and virtual MDIO node that is disabled by default
46 * and might need to be enabled, and also might need to have its mux-value
54 #include <asm/fsl_serdes.h>
58 #include <fdt_support.h>
59 #include <fsl_dtsec.h>
61 #include "../common/ngpixis.h"
62 #include "../common/fman.h"
64 #ifdef CONFIG_FMAN_ENET
66 #define BRDCFG1_EMI1_SEL_MASK 0x70
67 #define BRDCFG1_EMI1_SEL_SLOT1 0x10
68 #define BRDCFG1_EMI1_SEL_SLOT2 0x20
69 #define BRDCFG1_EMI1_SEL_SLOT5 0x30
70 #define BRDCFG1_EMI1_SEL_SLOT6 0x40
71 #define BRDCFG1_EMI1_SEL_SLOT7 0x50
72 #define BRDCFG1_EMI1_SEL_SLOT3 0x60
73 #define BRDCFG1_EMI1_SEL_RGMII 0x00
74 #define BRDCFG1_EMI1_EN 0x08
75 #define BRDCFG1_EMI2_SEL_MASK 0x06
76 #define BRDCFG1_EMI2_SEL_SLOT1 0x00
77 #define BRDCFG1_EMI2_SEL_SLOT2 0x02
79 #define BRDCFG2_REG_GPIO_SEL 0x20
82 #define PHY_BASE_ADDR 0x00
84 #define PORT_NUM_FM1 0x04
85 #define PORT_NUM_FM2 0x02
88 * BRDCFG1 mask and value for each MAC
90 * This array contains the BRDCFG1 values (in mask/val format) that route the
91 * MDIO bus to a particular RGMII or SGMII PHY.
96 } mdio_mux[NUM_FM_PORTS];
99 * Mapping of all 18 SERDES lanes to board slots. A value of '0' here means
100 * that the mapping must be determined dynamically, or that the lane maps to
101 * something other than a board slot
103 static u8 lane_to_slot[] = {
104 7, 7, 0, 0, 0, 0, 0, 0, 0, 0, 2, 2, 2, 2, 1, 1, 0, 0, 0, 0
108 * Set the board muxing for a given MAC
110 * The MDIO layer calls this function every time it wants to talk to a PHY.
112 void super_hydra_mux_mdio(u8 mask, u8 val)
114 clrsetbits_8(&pixis->brdcfg1, mask, val);
117 struct super_hydra_mdio {
120 struct mii_dev *realbus;
123 static int super_hydra_mdio_read(struct mii_dev *bus, int addr, int devad,
126 struct super_hydra_mdio *priv = bus->priv;
128 super_hydra_mux_mdio(priv->mask, priv->val);
130 return priv->realbus->read(priv->realbus, addr, devad, regnum);
133 static int super_hydra_mdio_write(struct mii_dev *bus, int addr, int devad,
134 int regnum, u16 value)
136 struct super_hydra_mdio *priv = bus->priv;
138 super_hydra_mux_mdio(priv->mask, priv->val);
140 return priv->realbus->write(priv->realbus, addr, devad, regnum, value);
143 static int super_hydra_mdio_reset(struct mii_dev *bus)
145 struct super_hydra_mdio *priv = bus->priv;
147 return priv->realbus->reset(priv->realbus);
150 static void super_hydra_mdio_set_mux(char *name, u8 mask, u8 val)
152 struct mii_dev *bus = miiphy_get_dev_by_name(name);
153 struct super_hydra_mdio *priv = bus->priv;
159 static int super_hydra_mdio_init(char *realbusname, char *fakebusname)
161 struct super_hydra_mdio *hmdio;
162 struct mii_dev *bus = mdio_alloc();
165 printf("Failed to allocate Hydra MDIO bus\n");
169 hmdio = malloc(sizeof(*hmdio));
171 printf("Failed to allocate Hydra private data\n");
176 bus->read = super_hydra_mdio_read;
177 bus->write = super_hydra_mdio_write;
178 bus->reset = super_hydra_mdio_reset;
179 strcpy(bus->name, fakebusname);
181 hmdio->realbus = miiphy_get_dev_by_name(realbusname);
183 if (!hmdio->realbus) {
184 printf("No bus with name %s\n", realbusname);
192 return mdio_register(bus);
196 * Given the following ...
198 * 1) A pointer to an Fman Ethernet node (as identified by the 'compat'
199 * compatible string and 'addr' physical address)
203 * ... update the phy-handle property of the Ethernet node to point to the
204 * right PHY. This assumes that we already know the PHY for each port. That
205 * information is stored in mdio_mux[].
207 * The offset of the Fman Ethernet node is also passed in for convenience, but
210 * Note that what we call "Fman ports" (enum fm_port) is really an Fman MAC.
211 * Inside the Fman, "ports" are things that connect to MACs. We only call them
212 * ports in U-Boot because on previous Ethernet devices (e.g. Gianfar), MACs
213 * and ports are the same thing.
215 void board_ft_fman_fixup_port(void *fdt, char *compat, phys_addr_t addr,
216 enum fm_port port, int offset)
218 enum srds_prtcl device;
222 /* RGMII and XGMII are already mapped correctly in the DTS */
224 if (fm_info_get_enet_if(port) == PHY_INTERFACE_MODE_SGMII) {
225 device = serdes_device_from_fm_port(port);
226 lane = serdes_get_first_lane(device);
227 slot = lane_to_slot[lane];
228 phy = fm_info_get_phy_address(port);
230 sprintf(alias, "phy_sgmii_slot%u_%x", slot, phy);
231 fdt_set_phy_handle(fdt, compat, addr, alias);
235 #define PIXIS_SW2_LANE_23_SEL 0x80
236 #define PIXIS_SW2_LANE_45_SEL 0x40
237 #define PIXIS_SW2_LANE_67_SEL_MASK 0x30
238 #define PIXIS_SW2_LANE_67_SEL_5 0x00
239 #define PIXIS_SW2_LANE_67_SEL_6 0x20
240 #define PIXIS_SW2_LANE_67_SEL_7 0x10
241 #define PIXIS_SW2_LANE_8_SEL 0x08
242 #define PIXIS_SW2_LANE_1617_SEL 0x04
243 #define PIXIS_SW11_LANE_9_SEL 0x04
245 * Initialize the lane_to_slot[] array.
247 * On the P4080DS "Expedition" board, the mapping of SERDES lanes to board
248 * slots is hard-coded. On the Hydra board, however, the mapping is controlled
249 * by board switch SW2, so the lane_to_slot[] array needs to be dynamically
252 static void initialize_lane_to_slot(void)
254 u8 sw2 = in_8(&PIXIS_SW(2));
255 /* SW11 appears in the programming model as SW9 */
256 u8 sw11 = in_8(&PIXIS_SW(9));
258 lane_to_slot[2] = (sw2 & PIXIS_SW2_LANE_23_SEL) ? 7 : 4;
259 lane_to_slot[3] = lane_to_slot[2];
261 lane_to_slot[4] = (sw2 & PIXIS_SW2_LANE_45_SEL) ? 7 : 6;
262 lane_to_slot[5] = lane_to_slot[4];
264 switch (sw2 & PIXIS_SW2_LANE_67_SEL_MASK) {
265 case PIXIS_SW2_LANE_67_SEL_5:
268 case PIXIS_SW2_LANE_67_SEL_6:
271 case PIXIS_SW2_LANE_67_SEL_7:
275 lane_to_slot[7] = lane_to_slot[6];
277 lane_to_slot[8] = (sw2 & PIXIS_SW2_LANE_8_SEL) ? 3 : 0;
278 lane_to_slot[9] = (sw11 & PIXIS_SW11_LANE_9_SEL) ? 0 : 3;
280 lane_to_slot[16] = (sw2 & PIXIS_SW2_LANE_1617_SEL) ? 1 : 0;
281 lane_to_slot[17] = lane_to_slot[16];
284 #endif /* #ifdef CONFIG_FMAN_ENET */
287 * Configure the status for the virtual MDIO nodes
289 * Rather than create the virtual MDIO nodes from scratch for each active
290 * virtual MDIO, we expect the DTS to have the nodes defined already, and we
291 * only enable the ones that are actually active.
293 * We assume that the DTS already hard-codes the status for all the
294 * virtual MDIO nodes to "disabled", so all we need to do is enable the
297 void fdt_fixup_board_enet(void *fdt)
299 #ifdef CONFIG_FMAN_ENET
303 for (i = FM1_DTSEC1; i < FM1_DTSEC1 + CONFIG_SYS_NUM_FM1_DTSEC; i++) {
304 int idx = i - FM1_DTSEC1;
306 switch (fm_info_get_enet_if(i)) {
307 case PHY_INTERFACE_MODE_SGMII:
308 lane = serdes_get_first_lane(SGMII_FM1_DTSEC1 + idx);
312 slot = lane_to_slot[lane];
313 sprintf(alias, "hydra_sg_slot%u", slot);
314 fdt_status_okay_by_alias(fdt, alias);
315 debug("Enabled MDIO node %s (slot %i)\n",
319 case PHY_INTERFACE_MODE_RGMII:
320 fdt_status_okay_by_alias(fdt, "hydra_rg");
321 debug("Enabled MDIO node hydra_rg\n");
328 lane = serdes_get_first_lane(XAUI_FM1);
332 slot = lane_to_slot[lane];
333 sprintf(alias, "hydra_xg_slot%u", slot);
334 fdt_status_okay_by_alias(fdt, alias);
335 debug("Enabled MDIO node %s (slot %i)\n", alias, slot);
338 #if CONFIG_SYS_NUM_FMAN == 2
339 for (i = FM2_DTSEC1; i < FM2_DTSEC1 + CONFIG_SYS_NUM_FM2_DTSEC; i++) {
340 int idx = i - FM2_DTSEC1;
342 switch (fm_info_get_enet_if(i)) {
343 case PHY_INTERFACE_MODE_SGMII:
344 lane = serdes_get_first_lane(SGMII_FM2_DTSEC1 + idx);
348 slot = lane_to_slot[lane];
349 sprintf(alias, "hydra_sg_slot%u", slot);
350 fdt_status_okay_by_alias(fdt, alias);
351 debug("Enabled MDIO node %s (slot %i)\n",
355 case PHY_INTERFACE_MODE_RGMII:
356 fdt_status_okay_by_alias(fdt, "hydra_rg");
357 debug("Enabled MDIO node hydra_rg\n");
364 lane = serdes_get_first_lane(XAUI_FM2);
368 slot = lane_to_slot[lane];
369 sprintf(alias, "hydra_xg_slot%u", slot);
370 fdt_status_okay_by_alias(fdt, alias);
371 debug("Enabled MDIO node %s (slot %i)\n", alias, slot);
373 #endif /* CONFIG_SYS_NUM_FMAN == 2 */
374 #endif /* CONFIG_FMAN_ENET */
378 * Mapping of SerDes Protocol to MDIO MUX value and PHY address.
381 * DTSEC1 | DTSEC2 | DTSEC3 | DTSEC4
382 * Mux Phy | Mux Phy | Mux Phy | Mux Phy
383 * Value Addr | Value Addr | Value Addr | Value Addr
384 * 0x00 2 1c | 2 1d | 2 1e | 2 1f
386 * 0x02 | | 3 1c | 3 1d
387 * 0x03 2 1c | 2 1d | 2 1e | 2 1f
388 * 0x04 2 1c | 2 1d | 2 1e | 2 1f
389 * 0x05 | | 3 1c | 3 1d
390 * 0x06 2 1c | 2 1d | 2 1e | 2 1f
392 * 0x11 2 1c | 2 1d | 2 1e | 2 1f
393 * 0x2a 2 | | 2 1e | 2 1f
394 * 0x34 6 1c | 6 1d | 4 1e | 4 1f
395 * 0x35 | | 3 1c | 3 1d
396 * 0x36 6 1c | 6 1d | 4 1e | 4 1f
399 * DTSEC1 | DTSEC2 | DTSEC3 | DTSEC4
400 * EMI1 | EMI1 | EMI1 | EMI1
401 * Mux Phy | Mux Phy | Mux Phy | Mux Phy
402 * Value Addr | Value Addr | Value Addr | Value Addr
403 * 0x00 | | 6 1c | 6 1d
405 * 0x02 | | 6 1c | 6 1d
406 * 0x03 3 1c | 3 1d | 6 1c | 6 1d
407 * 0x04 3 1c | 3 1d | 6 1c | 6 1d
408 * 0x05 | | 6 1c | 6 1d
409 * 0x06 | | 6 1c | 6 1d
418 int board_eth_init(bd_t *bis)
420 #ifdef CONFIG_FMAN_ENET
421 struct fsl_pq_mdio_info dtsec_mdio_info;
422 struct tgec_mdio_info tgec_mdio_info;
423 unsigned int i, slot;
428 ccsr_gur_t *gur = (void *)(CONFIG_SYS_MPC85xx_GUTS_ADDR);
429 int srds_prtcl = (in_be32(&gur->rcwsr[4]) &
430 FSL_CORENET_RCWSR4_SRDS_PRTCL) >> 26;
432 printf("Initializing Fman\n");
434 initialize_lane_to_slot();
436 /* We want to use the PIXIS to configure MUX routing, not GPIOs. */
437 setbits_8(&pixis->brdcfg2, BRDCFG2_REG_GPIO_SEL);
439 memset(mdio_mux, 0, sizeof(mdio_mux));
441 dtsec_mdio_info.regs =
442 (struct tsec_mii_mng *)CONFIG_SYS_FM1_DTSEC1_MDIO_ADDR;
443 dtsec_mdio_info.name = DEFAULT_FM_MDIO_NAME;
445 /* Register the real 1G MDIO bus */
446 fsl_pq_mdio_init(bis, &dtsec_mdio_info);
448 tgec_mdio_info.regs =
449 (struct tgec_mdio_controller *)CONFIG_SYS_FM1_TGEC_MDIO_ADDR;
450 tgec_mdio_info.name = DEFAULT_FM_TGEC_MDIO_NAME;
452 /* Register the real 10G MDIO bus */
453 fm_tgec_mdio_init(bis, &tgec_mdio_info);
455 /* Register the three virtual MDIO front-ends */
456 super_hydra_mdio_init(DEFAULT_FM_MDIO_NAME,
457 "SUPER_HYDRA_RGMII_MDIO");
458 super_hydra_mdio_init(DEFAULT_FM_MDIO_NAME,
459 "SUPER_HYDRA_FM1_SGMII_MDIO");
460 super_hydra_mdio_init(DEFAULT_FM_MDIO_NAME,
461 "SUPER_HYDRA_FM2_SGMII_MDIO");
462 super_hydra_mdio_init(DEFAULT_FM_MDIO_NAME,
463 "SUPER_HYDRA_FM3_SGMII_MDIO");
464 super_hydra_mdio_init(DEFAULT_FM_TGEC_MDIO_NAME,
465 "SUPER_HYDRA_FM1_TGEC_MDIO");
466 super_hydra_mdio_init(DEFAULT_FM_TGEC_MDIO_NAME,
467 "SUPER_HYDRA_FM2_TGEC_MDIO");
470 * Program the DTSEC PHY addresses assuming that they are all SGMII.
471 * For any DTSEC that's RGMII, we'll override its PHY address later.
472 * We assume that DTSEC5 is only used for RGMII.
474 fm_info_set_phy_address(FM1_DTSEC1, CONFIG_SYS_FM1_DTSEC1_PHY_ADDR);
475 fm_info_set_phy_address(FM1_DTSEC2, CONFIG_SYS_FM1_DTSEC2_PHY_ADDR);
476 fm_info_set_phy_address(FM1_10GEC1, CONFIG_SYS_FM2_10GEC1_PHY_ADDR);
478 #if (CONFIG_SYS_NUM_FMAN == 2)
479 fm_info_set_phy_address(FM2_DTSEC1, CONFIG_SYS_FM2_DTSEC1_PHY_ADDR);
480 fm_info_set_phy_address(FM2_DTSEC2, CONFIG_SYS_FM2_DTSEC2_PHY_ADDR);
481 fm_info_set_phy_address(FM2_DTSEC3, CONFIG_SYS_FM2_DTSEC1_PHY_ADDR);
482 fm_info_set_phy_address(FM2_DTSEC4, CONFIG_SYS_FM2_DTSEC2_PHY_ADDR);
483 fm_info_set_phy_address(FM2_10GEC1, CONFIG_SYS_FM1_10GEC1_PHY_ADDR);
486 switch (srds_prtcl) {
495 fm_info_set_phy_address(FM1_DTSEC3,
496 CONFIG_SYS_FM1_DTSEC3_PHY_ADDR);
497 fm_info_set_phy_address(FM1_DTSEC4,
498 CONFIG_SYS_FM1_DTSEC4_PHY_ADDR);
505 fm_info_set_phy_address(FM1_DTSEC3,
506 CONFIG_SYS_FM1_DTSEC1_PHY_ADDR);
507 fm_info_set_phy_address(FM1_DTSEC4,
508 CONFIG_SYS_FM1_DTSEC2_PHY_ADDR);
511 printf("Fman: Unsupport SerDes Protocol 0x%02x\n", srds_prtcl);
515 for (i = FM1_DTSEC1; i < FM1_DTSEC1 + CONFIG_SYS_NUM_FM1_DTSEC; i++) {
516 int idx = i - FM1_DTSEC1;
518 switch (fm_info_get_enet_if(i)) {
519 case PHY_INTERFACE_MODE_SGMII:
520 lane = serdes_get_first_lane(SGMII_FM1_DTSEC1 + idx);
523 slot = lane_to_slot[lane];
524 mdio_mux[i].mask = BRDCFG1_EMI1_SEL_MASK;
525 debug("FM1@DTSEC%u expects SGMII in slot %u\n",
529 mdio_mux[i].val = BRDCFG1_EMI1_SEL_SLOT1 |
533 mdio_mux[i].val = BRDCFG1_EMI1_SEL_SLOT2 |
537 mdio_mux[i].val = BRDCFG1_EMI1_SEL_SLOT3 |
541 mdio_mux[i].val = BRDCFG1_EMI1_SEL_SLOT5 |
545 mdio_mux[i].val = BRDCFG1_EMI1_SEL_SLOT6 |
549 mdio_mux[i].val = BRDCFG1_EMI1_SEL_SLOT7 |
554 super_hydra_mdio_set_mux("SUPER_HYDRA_FM1_SGMII_MDIO",
555 mdio_mux[i].mask, mdio_mux[i].val);
557 miiphy_get_dev_by_name("SUPER_HYDRA_FM1_SGMII_MDIO"));
559 case PHY_INTERFACE_MODE_RGMII:
561 * FM1 DTSEC5 is routed via EC1 to the first on-board
562 * RGMII port. FM2 DTSEC5 is routed via EC2 to the
563 * second on-board RGMII port. The other DTSECs cannot
564 * be routed to RGMII.
566 debug("FM1@DTSEC%u is RGMII at address %u\n",
568 fm_info_set_phy_address(i, 0);
569 mdio_mux[i].mask = BRDCFG1_EMI1_SEL_MASK;
570 mdio_mux[i].val = BRDCFG1_EMI1_SEL_RGMII |
572 super_hydra_mdio_set_mux("SUPER_HYDRA_RGMII_MDIO",
573 mdio_mux[i].mask, mdio_mux[i].val);
575 miiphy_get_dev_by_name("SUPER_HYDRA_RGMII_MDIO"));
577 case PHY_INTERFACE_MODE_NONE:
578 fm_info_set_phy_address(i, 0);
581 printf("Fman1: DTSEC%u set to unknown interface %i\n",
582 idx + 1, fm_info_get_enet_if(i));
583 fm_info_set_phy_address(i, 0);
588 bus = miiphy_get_dev_by_name("SUPER_HYDRA_FM1_SGMII_MDIO");
589 qsgmii = is_qsgmii_riser_card(bus, PHY_BASE_ADDR, PORT_NUM_FM1, REGNUM);
592 for (i = FM1_DTSEC1; i < FM1_DTSEC1 + PORT_NUM_FM1; i++) {
593 if (fm_info_get_enet_if(i) ==
594 PHY_INTERFACE_MODE_SGMII) {
595 phy_real_addr = PHY_BASE_ADDR + i - FM1_DTSEC1;
596 fm_info_set_phy_address(i, phy_real_addr);
599 switch (srds_prtcl) {
608 fm_info_set_phy_address(FM1_DTSEC3, PHY_BASE_ADDR + 2);
609 fm_info_set_phy_address(FM1_DTSEC4, PHY_BASE_ADDR + 3);
616 fm_info_set_phy_address(FM1_DTSEC3, PHY_BASE_ADDR + 0);
617 fm_info_set_phy_address(FM1_DTSEC4, PHY_BASE_ADDR + 1);
625 * For 10G, we only support one XAUI card per Fman. If present, then we
626 * force its routing and never touch those bits again, which removes the
627 * need for Linux to do any muxing. This works because of the way
628 * BRDCFG1 is defined, but it's a bit hackish.
630 * The PHY address for the XAUI card depends on which slot it's in. The
631 * macros we use imply that the PHY address is based on which FM, but
632 * that's not true. On the P4080DS, FM1 could only use XAUI in slot 5,
633 * and FM2 could only use a XAUI in slot 4. On the Hydra board, we
634 * check the actual slot and just use the macros as-is, even though
635 * the P3041 and P5020 only have one Fman.
637 lane = serdes_get_first_lane(XAUI_FM1);
639 debug("FM1@TGEC1 expects XAUI in slot %u\n", lane_to_slot[lane]);
640 mdio_mux[i].mask = BRDCFG1_EMI2_SEL_MASK;
641 mdio_mux[i].val = BRDCFG1_EMI2_SEL_SLOT2;
642 super_hydra_mdio_set_mux("SUPER_HYDRA_FM1_TGEC_MDIO",
643 mdio_mux[i].mask, mdio_mux[i].val);
646 fm_info_set_mdio(FM1_10GEC1,
647 miiphy_get_dev_by_name("SUPER_HYDRA_FM1_TGEC_MDIO"));
649 #if (CONFIG_SYS_NUM_FMAN == 2)
650 for (i = FM2_DTSEC1; i < FM2_DTSEC1 + CONFIG_SYS_NUM_FM2_DTSEC; i++) {
651 int idx = i - FM2_DTSEC1;
653 switch (fm_info_get_enet_if(i)) {
654 case PHY_INTERFACE_MODE_SGMII:
655 lane = serdes_get_first_lane(SGMII_FM2_DTSEC1 + idx);
658 slot = lane_to_slot[lane];
659 mdio_mux[i].mask = BRDCFG1_EMI1_SEL_MASK;
660 debug("FM2@DTSEC%u expects SGMII in slot %u\n",
664 mdio_mux[i].val = BRDCFG1_EMI1_SEL_SLOT1 |
668 mdio_mux[i].val = BRDCFG1_EMI1_SEL_SLOT2 |
672 mdio_mux[i].val = BRDCFG1_EMI1_SEL_SLOT3 |
676 mdio_mux[i].val = BRDCFG1_EMI1_SEL_SLOT5 |
680 mdio_mux[i].val = BRDCFG1_EMI1_SEL_SLOT6 |
684 mdio_mux[i].val = BRDCFG1_EMI1_SEL_SLOT7 |
689 if (i == FM2_DTSEC1 || i == FM2_DTSEC2) {
690 super_hydra_mdio_set_mux(
691 "SUPER_HYDRA_FM3_SGMII_MDIO",
694 fm_info_set_mdio(i, miiphy_get_dev_by_name(
695 "SUPER_HYDRA_FM3_SGMII_MDIO"));
697 super_hydra_mdio_set_mux(
698 "SUPER_HYDRA_FM2_SGMII_MDIO",
701 fm_info_set_mdio(i, miiphy_get_dev_by_name(
702 "SUPER_HYDRA_FM2_SGMII_MDIO"));
706 case PHY_INTERFACE_MODE_RGMII:
708 * FM1 DTSEC5 is routed via EC1 to the first on-board
709 * RGMII port. FM2 DTSEC5 is routed via EC2 to the
710 * second on-board RGMII port. The other DTSECs cannot
711 * be routed to RGMII.
713 debug("FM2@DTSEC%u is RGMII at address %u\n",
715 fm_info_set_phy_address(i, 1);
716 mdio_mux[i].mask = BRDCFG1_EMI1_SEL_MASK;
717 mdio_mux[i].val = BRDCFG1_EMI1_SEL_RGMII |
719 super_hydra_mdio_set_mux("SUPER_HYDRA_RGMII_MDIO",
720 mdio_mux[i].mask, mdio_mux[i].val);
722 miiphy_get_dev_by_name("SUPER_HYDRA_RGMII_MDIO"));
724 case PHY_INTERFACE_MODE_NONE:
725 fm_info_set_phy_address(i, 0);
728 printf("Fman2: DTSEC%u set to unknown interface %i\n",
729 idx + 1, fm_info_get_enet_if(i));
730 fm_info_set_phy_address(i, 0);
735 bus = miiphy_get_dev_by_name("SUPER_HYDRA_FM2_SGMII_MDIO");
736 set_sgmii_phy(bus, FM2_DTSEC3, PORT_NUM_FM2, PHY_BASE_ADDR);
737 bus = miiphy_get_dev_by_name("SUPER_HYDRA_FM3_SGMII_MDIO");
738 set_sgmii_phy(bus, FM2_DTSEC1, PORT_NUM_FM2, PHY_BASE_ADDR);
741 * For 10G, we only support one XAUI card per Fman. If present, then we
742 * force its routing and never touch those bits again, which removes the
743 * need for Linux to do any muxing. This works because of the way
744 * BRDCFG1 is defined, but it's a bit hackish.
746 * The PHY address for the XAUI card depends on which slot it's in. The
747 * macros we use imply that the PHY address is based on which FM, but
748 * that's not true. On the P4080DS, FM1 could only use XAUI in slot 5,
749 * and FM2 could only use a XAUI in slot 4. On the Hydra board, we
750 * check the actual slot and just use the macros as-is, even though
751 * the P3041 and P5020 only have one Fman.
753 lane = serdes_get_first_lane(XAUI_FM2);
755 debug("FM2@TGEC1 expects XAUI in slot %u\n", lane_to_slot[lane]);
756 mdio_mux[i].mask = BRDCFG1_EMI2_SEL_MASK;
757 mdio_mux[i].val = BRDCFG1_EMI2_SEL_SLOT1;
758 super_hydra_mdio_set_mux("SUPER_HYDRA_FM2_TGEC_MDIO",
759 mdio_mux[i].mask, mdio_mux[i].val);
762 fm_info_set_mdio(FM2_10GEC1,
763 miiphy_get_dev_by_name("SUPER_HYDRA_FM2_TGEC_MDIO"));
770 return pci_eth_init(bis);