board/engicam/geam6ul/geam6ul.c

   1 /*
   2  * Copyright (C) 2016 Amarula Solutions B.V.
   3  * Copyright (C) 2016 Engicam S.r.l.
   4  * Author: Jagan Teki <jagan@amarulasolutions.com>
   5  *
   6  * SPDX-License-Identifier:     GPL-2.0+
   7  */
   8
   9 #include <common.h>
  10
  11 #include <asm/io.h>
  12 #include <asm/gpio.h>
  13 #include <linux/sizes.h>
  14
  15 #include <asm/arch/clock.h>
  16 #include <asm/arch/iomux.h>
  17 #include <asm/arch/mx6-pins.h>
  18 #include <asm/arch/sys_proto.h>
  19 #include <asm/imx-common/iomux-v3.h>
  20
  21 DECLARE_GLOBAL_DATA_PTR;
  22
  23 #define UART_PAD_CTRL  (PAD_CTL_PKE | PAD_CTL_PUE |             \
  24         PAD_CTL_PUS_100K_UP | PAD_CTL_SPEED_MED |               \
  25         PAD_CTL_DSE_40ohm   | PAD_CTL_SRE_FAST  | PAD_CTL_HYS)
  26
  27 static iomux_v3_cfg_t const uart1_pads[] = {
  28         MX6_PAD_UART1_TX_DATA__UART1_DCE_TX | MUX_PAD_CTRL(UART_PAD_CTRL),
  29         MX6_PAD_UART1_RX_DATA__UART1_DCE_RX | MUX_PAD_CTRL(UART_PAD_CTRL),
  30 };
  31
  32 int board_early_init_f(void)
  33 {
  34         imx_iomux_v3_setup_multiple_pads(uart1_pads, ARRAY_SIZE(uart1_pads));
  35
  36         return 0;
  37 }
  38
  39 int board_init(void)
  40 {
  41         /* Address of boot parameters */
  42         gd->bd->bi_boot_params = PHYS_SDRAM + 0x100;
  43
  44         return 0;
  45 }
  46
  47 int dram_init(void)
  48 {
  49         gd->ram_size = imx_ddr_size();
  50
  51         return 0;
  52 }
  53
  54 #ifdef CONFIG_SPL_BUILD
  55 #include <libfdt.h>
  56 #include <spl.h>
  57
  58 #include <asm/arch/crm_regs.h>
  59 #include <asm/arch/mx6-ddr.h>
  60
  61 /* MMC board initialization is needed till adding DM support in SPL */
  62 #if defined(CONFIG_FSL_ESDHC) && !defined(CONFIG_DM_MMC)
  63 #include <mmc.h>
  64 #include <fsl_esdhc.h>
  65
  66 #define USDHC_PAD_CTRL (PAD_CTL_PKE | PAD_CTL_PUE |             \
  67         PAD_CTL_PUS_22K_UP  | PAD_CTL_SPEED_LOW |               \
  68         PAD_CTL_DSE_80ohm   | PAD_CTL_SRE_FAST  | PAD_CTL_HYS)
  69
  70 static iomux_v3_cfg_t const usdhc1_pads[] = {
  71         MX6_PAD_SD1_CLK__USDHC1_CLK | MUX_PAD_CTRL(USDHC_PAD_CTRL),
  72         MX6_PAD_SD1_CMD__USDHC1_CMD | MUX_PAD_CTRL(USDHC_PAD_CTRL),
  73         MX6_PAD_SD1_DATA0__USDHC1_DATA0 | MUX_PAD_CTRL(USDHC_PAD_CTRL),
  74         MX6_PAD_SD1_DATA1__USDHC1_DATA1 | MUX_PAD_CTRL(USDHC_PAD_CTRL),
  75         MX6_PAD_SD1_DATA2__USDHC1_DATA2 | MUX_PAD_CTRL(USDHC_PAD_CTRL),
  76         MX6_PAD_SD1_DATA3__USDHC1_DATA3 | MUX_PAD_CTRL(USDHC_PAD_CTRL),
  77
  78         /* VSELECT */
  79         MX6_PAD_GPIO1_IO05__USDHC1_VSELECT | MUX_PAD_CTRL(USDHC_PAD_CTRL),
  80         /* CD */
  81         MX6_PAD_UART1_RTS_B__GPIO1_IO19 | MUX_PAD_CTRL(NO_PAD_CTRL),
  82         /* RST_B */
  83         MX6_PAD_GPIO1_IO09__GPIO1_IO09 | MUX_PAD_CTRL(NO_PAD_CTRL),
  84 };
  85
  86 #define USDHC1_CD_GPIO  IMX_GPIO_NR(1, 1)
  87
  88 struct fsl_esdhc_cfg usdhc_cfg[1] = {
  89         {USDHC1_BASE_ADDR, 0, 4},
  90 };
  91
  92 int board_mmc_getcd(struct mmc *mmc)
  93 {
  94         struct fsl_esdhc_cfg *cfg = (struct fsl_esdhc_cfg *)mmc->priv;
  95         int ret = 0;
  96
  97         switch (cfg->esdhc_base) {
  98         case USDHC1_BASE_ADDR:
  99                 ret = !gpio_get_value(USDHC1_CD_GPIO);
 100                 break;
 101         }
 102
 103         return ret;
 104 }
 105
 106 int board_mmc_init(bd_t *bis)
 107 {
 108         int i, ret;
 109
 110         /*
 111         * According to the board_mmc_init() the following map is done:
 112         * (U-boot device node)    (Physical Port)
 113         * mmc0                          USDHC1
 114         */
 115         for (i = 0; i < CONFIG_SYS_FSL_USDHC_NUM; i++) {
 116                 switch (i) {
 117                 case 0:
 118                         imx_iomux_v3_setup_multiple_pads(
 119                                 usdhc1_pads, ARRAY_SIZE(usdhc1_pads));
 120                         gpio_direction_input(USDHC1_CD_GPIO);
 121                         usdhc_cfg[0].sdhc_clk = mxc_get_clock(MXC_ESDHC_CLK);
 122                         break;
 123                 default:
 124                         printf("Warning - USDHC%d controller not supporting\n",
 125                                i + 1);
 126                         return 0;
 127                 }
 128
 129                 ret = fsl_esdhc_initialize(bis, &usdhc_cfg[i]);
 130                 if (ret) {
 131                         printf("Warning: failed to initialize mmc dev %d\n", i);
 132                         return ret;
 133                 }
 134         }
 135
 136         return 0;
 137 }
 138 #endif /* CONFIG_FSL_ESDHC */
 139
 140 static struct mx6ul_iomux_grp_regs mx6_grp_ioregs = {
 141         .grp_addds = 0x00000030,
 142         .grp_ddrmode_ctl = 0x00020000,
 143         .grp_b0ds = 0x00000030,
 144         .grp_ctlds = 0x00000030,
 145         .grp_b1ds = 0x00000030,
 146         .grp_ddrpke = 0x00000000,
 147         .grp_ddrmode = 0x00020000,
 148         .grp_ddr_type = 0x000c0000,
 149 };
 150
 151 static struct mx6ul_iomux_ddr_regs mx6_ddr_ioregs = {
 152         .dram_dqm0 = 0x00000030,
 153         .dram_dqm1 = 0x00000030,
 154         .dram_ras = 0x00000030,
 155         .dram_cas = 0x00000030,
 156         .dram_odt0 = 0x00000030,
 157         .dram_odt1 = 0x00000030,
 158         .dram_sdba2 = 0x00000000,
 159         .dram_sdclk_0 = 0x00000008,
 160         .dram_sdqs0 = 0x00000038,
 161         .dram_sdqs1 = 0x00000030,
 162         .dram_reset = 0x00000030,
 163 };
 164
 165 static struct mx6_mmdc_calibration mx6_mmcd_calib = {
 166         .p0_mpwldectrl0 = 0x00070007,
 167         .p0_mpdgctrl0 = 0x41490145,
 168         .p0_mprddlctl = 0x40404546,
 169         .p0_mpwrdlctl = 0x4040524D,
 170 };
 171
 172 struct mx6_ddr_sysinfo ddr_sysinfo = {
 173         .dsize = 0,
 174         .cs_density = 20,
 175         .ncs = 1,
 176         .cs1_mirror = 0,
 177         .rtt_wr = 2,
 178         .rtt_nom = 1,           /* RTT_Nom = RZQ/2 */
 179         .walat = 1,             /* Write additional latency */
 180         .ralat = 5,             /* Read additional latency */
 181         .mif3_mode = 3,         /* Command prediction working mode */
 182         .bi_on = 1,             /* Bank interleaving enabled */
 183         .sde_to_rst = 0x10,     /* 14 cycles, 200us (JEDEC default) */
 184         .rst_to_cke = 0x23,     /* 33 cycles, 500us (JEDEC default) */
 185         .ddr_type = DDR_TYPE_DDR3,
 186 };
 187
 188 static struct mx6_ddr3_cfg mem_ddr = {
 189         .mem_speed = 800,
 190         .density = 4,
 191         .width = 16,
 192         .banks = 8,
 193         .rowaddr = 13,
 194         .coladdr = 10,
 195         .pagesz = 2,
 196         .trcd = 1375,
 197         .trcmin = 4875,
 198         .trasmin = 3500,
 199 };
 200
 201 static void ccgr_init(void)
 202 {
 203         struct mxc_ccm_reg *ccm = (struct mxc_ccm_reg *)CCM_BASE_ADDR;
 204
 205         writel(0xFFFFFFFF, &ccm->CCGR0);
 206         writel(0xFFFFFFFF, &ccm->CCGR1);
 207         writel(0xFFFFFFFF, &ccm->CCGR2);
 208         writel(0xFFFFFFFF, &ccm->CCGR3);
 209         writel(0xFFFFFFFF, &ccm->CCGR4);
 210         writel(0xFFFFFFFF, &ccm->CCGR5);
 211         writel(0xFFFFFFFF, &ccm->CCGR6);
 212         writel(0xFFFFFFFF, &ccm->CCGR7);
 213 }
 214
 215 static void spl_dram_init(void)
 216 {
 217         mx6ul_dram_iocfg(mem_ddr.width, &mx6_ddr_ioregs, &mx6_grp_ioregs);
 218         mx6_dram_cfg(&ddr_sysinfo, &mx6_mmcd_calib, &mem_ddr);
 219 }
 220
 221 void board_init_f(ulong dummy)
 222 {
 223         /* setup AIPS and disable watchdog */
 224         arch_cpu_init();
 225
 226         ccgr_init();
 227
 228         /* iomux and setup of i2c */
 229         board_early_init_f();
 230
 231         /* setup GP timer */
 232         timer_init();
 233
 234         /* UART clocks enabled and gd valid - init serial console */
 235         preloader_console_init();
 236
 237         /* DDR initialization */
 238         spl_dram_init();
 239
 240         /* Clear the BSS. */
 241         memset(__bss_start, 0, __bss_end - __bss_start);
 242
 243         /* load/boot image from boot device */
 244         board_init_r(NULL, 0);
 245 }
 246 #endif /* CONFIG_SPL_BUILD */