board/cloudengines/pogo_e02/pogo_e02.c

   1 // SPDX-License-Identifier: GPL-2.0+
   2 /*
   3  * Copyright (C) 2012
   4  * David Purdy <david.c.purdy@gmail.com>
   5  *
   6  * Based on Kirkwood support:
   7  * (C) Copyright 2009
   8  * Marvell Semiconductor <www.marvell.com>
   9  * Written-by: Prafulla Wadaskar <prafulla@marvell.com>
  10  */
  11
  12 #include <common.h>
  13 #include <miiphy.h>
  14 #include <asm/arch/cpu.h>
  15 #include <asm/arch/soc.h>
  16 #include <asm/arch/mpp.h>
  17 #include "pogo_e02.h"
  18
  19 DECLARE_GLOBAL_DATA_PTR;
  20
  21 int board_early_init_f(void)
  22 {
  23         /*
  24          * default gpio configuration
  25          * There are maximum 64 gpios controlled through 2 sets of registers
  26          * the  below configuration configures mainly initial LED status
  27          */
  28         mvebu_config_gpio(POGO_E02_OE_VAL_LOW,
  29                           POGO_E02_OE_VAL_HIGH,
  30                           POGO_E02_OE_LOW, POGO_E02_OE_HIGH);
  31
  32         /* Multi-Purpose Pins Functionality configuration */
  33         static const u32 kwmpp_config[] = {
  34                 MPP0_NF_IO2,
  35                 MPP1_NF_IO3,
  36                 MPP2_NF_IO4,
  37                 MPP3_NF_IO5,
  38                 MPP4_NF_IO6,
  39                 MPP5_NF_IO7,
  40                 MPP6_SYSRST_OUTn,
  41                 MPP7_GPO,
  42                 MPP8_UART0_RTS,
  43                 MPP9_UART0_CTS,
  44                 MPP10_UART0_TXD,
  45                 MPP11_UART0_RXD,
  46                 MPP12_SD_CLK,
  47                 MPP13_SD_CMD,
  48                 MPP14_SD_D0,
  49                 MPP15_SD_D1,
  50                 MPP16_SD_D2,
  51                 MPP17_SD_D3,
  52                 MPP18_NF_IO0,
  53                 MPP19_NF_IO1,
  54                 MPP29_TSMP9,    /* USB Power Enable */
  55                 MPP48_GPIO,     /* LED green */
  56                 MPP49_GPIO,     /* LED orange */
  57                 0
  58         };
  59         kirkwood_mpp_conf(kwmpp_config, NULL);
  60         return 0;
  61 }
  62
  63 int board_init(void)
  64 {
  65         /* Boot parameters address */
  66         gd->bd->bi_boot_params = mvebu_sdram_bar(0) + 0x100;
  67
  68         return 0;
  69 }
  70
  71 #ifdef CONFIG_RESET_PHY_R
  72 /* Configure and initialize PHY */
  73 void reset_phy(void)
  74 {
  75         u16 reg;
  76         u16 devadr;
  77         char *name = "egiga0";
  78
  79         if (miiphy_set_current_dev(name))
  80                 return;
  81
  82         /* command to read PHY dev address */
  83         if (miiphy_read(name, 0xEE, 0xEE, (u16 *) &devadr)) {
  84                 printf("Err..(%s) could not read PHY dev address\n", __func__);
  85                 return;
  86         }
  87
  88         /*
  89          * Enable RGMII delay on Tx and Rx for CPU port
  90          * Ref: sec 4.7.2 of chip datasheet
  91          */
  92         miiphy_write(name, devadr, MV88E1116_PGADR_REG, 2);
  93         miiphy_read(name, devadr, MV88E1116_MAC_CTRL_REG, &reg);
  94         reg |= (MV88E1116_RGMII_RXTM_CTRL | MV88E1116_RGMII_TXTM_CTRL);
  95         miiphy_write(name, devadr, MV88E1116_MAC_CTRL_REG, reg);
  96         miiphy_write(name, devadr, MV88E1116_PGADR_REG, 0);
  97
  98         /* reset the phy */
  99         miiphy_reset(name, devadr);
 100
 101         debug("88E1116 Initialized on %s\n", name);
 102 }
 103 #endif /* CONFIG_RESET_PHY_R */