1 // SPDX-License-Identifier: GPL-2.0+
5 * common board functions for B&R boards
7 * Copyright (C) 2013 Hannes Schmelzer <oe5hpm@oevsv.at>
8 * Bernecker & Rainer Industrieelektronik GmbH - http://www.br-automation.com
17 #include <asm/global_data.h>
18 #include <linux/delay.h>
19 #include "bur_common.h"
21 DECLARE_GLOBAL_DATA_PTR;
23 /* --------------------------------------------------------------------------*/
25 int ft_board_setup(void *blob, struct bd_info *bd)
29 nodeoffset = fdt_path_offset(blob, "/factory-settings");
31 printf("%s: cannot find /factory-settings, trying /fset\n",
33 nodeoffset = fdt_path_offset(blob, "/fset");
35 printf("%s: cannot find /fset.\n", __func__);
40 if (fdt_setprop(blob, nodeoffset, "bl-version",
41 PLAIN_VERSION, strlen(PLAIN_VERSION)) != 0) {
42 printf("%s: no 'bl-version' prop in fdt!\n", __func__);
48 int brdefaultip_setup(int bus, int chip)
51 struct udevice *i2cdev;
53 char defip[256] = { 0 };
55 rc = i2c_get_chip_for_busnum(bus, chip, 2, &i2cdev);
57 printf("WARN: cannot probe baseboard EEPROM!\n");
61 rc = dm_i2c_read(i2cdev, 0, &u8buf, 1);
63 printf("WARN: cannot read baseboard EEPROM!\n");
68 snprintf(defip, sizeof(defip),
69 "if test -r ${ipaddr}; then; else setenv ipaddr 192.168.60.%d; setenv serverip 192.168.60.254; setenv gatewayip 192.168.60.254; setenv netmask 255.255.255.0; fi;",
73 "if test -r ${ipaddr}; then; else setenv ipaddr 192.168.60.1; setenv serverip 192.168.60.254; setenv gatewayip 192.168.60.254; setenv netmask 255.255.255.0; fi;",
76 env_set("brdefaultip", defip);
77 env_set_hex("board_id", u8buf);
82 int overwrite_console(void)
87 #if defined(CONFIG_SPL_BUILD) && defined(CONFIG_AM33XX)
88 #include <asm/arch/hardware.h>
89 #include <asm/arch/omap.h>
90 #include <asm/arch/clock.h>
91 #include <asm/arch/sys_proto.h>
92 #include <power/tps65217.h>
94 static struct ctrl_dev *cdev = (struct ctrl_dev *)CTRL_DEVICE_BASE;
96 void pmicsetup(u32 mpupll, unsigned int bus)
101 if (power_tps65217_init(bus)) {
102 printf("WARN: cannot setup PMIC 0x24 @ bus #%d, not found!.\n",
107 /* Get the frequency which is defined by device fuses */
108 dpll_mpu_opp100.m = am335x_get_efuse_mpu_max_freq(cdev);
109 printf("detected max. frequency: %d - ", dpll_mpu_opp100.m);
112 dpll_mpu_opp100.m = mpupll;
113 printf("retuning MPU-PLL to: %d MHz.\n", dpll_mpu_opp100.m);
118 * Increase USB current limit to 1300mA or 1800mA and set
119 * the MPU voltage controller as needed.
121 if (dpll_mpu_opp100.m == MPUPLL_M_1000) {
122 usb_cur_lim = TPS65217_USB_INPUT_CUR_LIMIT_1800MA;
123 mpu_vdd = TPS65217_DCDC_VOLT_SEL_1325MV;
125 usb_cur_lim = TPS65217_USB_INPUT_CUR_LIMIT_1300MA;
126 mpu_vdd = TPS65217_DCDC_VOLT_SEL_1275MV;
129 if (tps65217_reg_write(TPS65217_PROT_LEVEL_NONE, TPS65217_POWER_PATH,
130 usb_cur_lim, TPS65217_USB_INPUT_CUR_LIMIT_MASK))
131 puts("tps65217_reg_write failure\n");
133 /* Set DCDC3 (CORE) voltage to 1.125V */
134 if (tps65217_voltage_update(TPS65217_DEFDCDC3,
135 TPS65217_DCDC_VOLT_SEL_1125MV)) {
136 puts("tps65217_voltage_update failure\n");
140 /* Set CORE Frequencies to OPP100 */
141 do_setup_dpll(&dpll_core_regs, &dpll_core_opp100);
143 /* Set DCDC2 (MPU) voltage */
144 if (tps65217_voltage_update(TPS65217_DEFDCDC2, mpu_vdd)) {
145 puts("tps65217_voltage_update failure\n");
149 /* Set LDO3 to 1.8V */
150 if (tps65217_reg_write(TPS65217_PROT_LEVEL_2,
152 TPS65217_LDO_VOLTAGE_OUT_1_8,
154 puts("tps65217_reg_write failure\n");
155 /* Set LDO4 to 3.3V */
156 if (tps65217_reg_write(TPS65217_PROT_LEVEL_2,
158 TPS65217_LDO_VOLTAGE_OUT_3_3,
160 puts("tps65217_reg_write failure\n");
162 /* Set MPU Frequency to what we detected now that voltages are set */
163 do_setup_dpll(&dpll_mpu_regs, &dpll_mpu_opp100);
164 /* Set PWR_EN bit in Status Register */
165 tps65217_reg_write(TPS65217_PROT_LEVEL_NONE,
166 TPS65217_STATUS, TPS65217_PWR_OFF, TPS65217_PWR_OFF);
169 void set_uart_mux_conf(void)
171 enable_uart0_pin_mux();
174 void set_mux_conf_regs(void)
176 enable_board_pin_mux();
179 #endif /* CONFIG_SPL_BUILD && CONFIG_AM33XX */