arch/powerpc/platforms/powermac/smp.c

   1 // SPDX-License-Identifier: GPL-2.0-or-later
   2 /*
   3  * SMP support for power macintosh.
   4  *
   5  * We support both the old "powersurge" SMP architecture
   6  * and the current Core99 (G4 PowerMac) machines.
   7  *
   8  * Note that we don't support the very first rev. of
   9  * Apple/DayStar 2 CPUs board, the one with the funky
  10  * watchdog. Hopefully, none of these should be there except
  11  * maybe internally to Apple. I should probably still add some
  12  * code to detect this card though and disable SMP. --BenH.
  13  *
  14  * Support Macintosh G4 SMP by Troy Benjegerdes (hozer@drgw.net)
  15  * and Ben Herrenschmidt <benh@kernel.crashing.org>.
  16  *
  17  * Support for DayStar quad CPU cards
  18  * Copyright (C) XLR8, Inc. 1994-2000
  19  */
  20 #include <linux/kernel.h>
  21 #include <linux/sched.h>
  22 #include <linux/sched/hotplug.h>
  23 #include <linux/smp.h>
  24 #include <linux/interrupt.h>
  25 #include <linux/kernel_stat.h>
  26 #include <linux/delay.h>
  27 #include <linux/init.h>
  28 #include <linux/spinlock.h>
  29 #include <linux/errno.h>
  30 #include <linux/hardirq.h>
  31 #include <linux/cpu.h>
  32 #include <linux/compiler.h>
  33 #include <linux/pgtable.h>
  34
  35 #include <asm/ptrace.h>
  36 #include <linux/atomic.h>
  37 #include <asm/code-patching.h>
  38 #include <asm/irq.h>
  39 #include <asm/page.h>
  40 #include <asm/sections.h>
  41 #include <asm/io.h>
  42 #include <asm/prom.h>
  43 #include <asm/smp.h>
  44 #include <asm/machdep.h>
  45 #include <asm/pmac_feature.h>
  46 #include <asm/time.h>
  47 #include <asm/mpic.h>
  48 #include <asm/cacheflush.h>
  49 #include <asm/keylargo.h>
  50 #include <asm/pmac_low_i2c.h>
  51 #include <asm/pmac_pfunc.h>
  52 #include <asm/inst.h>
  53
  54 #include "pmac.h"
  55
  56 #undef DEBUG
  57
  58 #ifdef DEBUG
  59 #define DBG(fmt...) udbg_printf(fmt)
  60 #else
  61 #define DBG(fmt...)
  62 #endif
  63
  64 extern void __secondary_start_pmac_0(void);
  65
  66 static void (*pmac_tb_freeze)(int freeze);
  67 static u64 timebase;
  68 static int tb_req;
  69
  70 #ifdef CONFIG_PPC_PMAC32_PSURGE
  71
  72 /*
  73  * Powersurge (old powermac SMP) support.
  74  */
  75
  76 /* Addresses for powersurge registers */
  77 #define HAMMERHEAD_BASE         0xf8000000
  78 #define HHEAD_CONFIG            0x90
  79 #define HHEAD_SEC_INTR          0xc0
  80
  81 /* register for interrupting the primary processor on the powersurge */
  82 /* N.B. this is actually the ethernet ROM! */
  83 #define PSURGE_PRI_INTR         0xf3019000
  84
  85 /* register for storing the start address for the secondary processor */
  86 /* N.B. this is the PCI config space address register for the 1st bridge */
  87 #define PSURGE_START            0xf2800000
  88
  89 /* Daystar/XLR8 4-CPU card */
  90 #define PSURGE_QUAD_REG_ADDR    0xf8800000
  91
  92 #define PSURGE_QUAD_IRQ_SET     0
  93 #define PSURGE_QUAD_IRQ_CLR     1
  94 #define PSURGE_QUAD_IRQ_PRIMARY 2
  95 #define PSURGE_QUAD_CKSTOP_CTL  3
  96 #define PSURGE_QUAD_PRIMARY_ARB 4
  97 #define PSURGE_QUAD_BOARD_ID    6
  98 #define PSURGE_QUAD_WHICH_CPU   7
  99 #define PSURGE_QUAD_CKSTOP_RDBK 8
 100 #define PSURGE_QUAD_RESET_CTL   11
 101
 102 #define PSURGE_QUAD_OUT(r, v)   (out_8(quad_base + ((r) << 4) + 4, (v)))
 103 #define PSURGE_QUAD_IN(r)       (in_8(quad_base + ((r) << 4) + 4) & 0x0f)
 104 #define PSURGE_QUAD_BIS(r, v)   (PSURGE_QUAD_OUT((r), PSURGE_QUAD_IN(r) | (v)))
 105 #define PSURGE_QUAD_BIC(r, v)   (PSURGE_QUAD_OUT((r), PSURGE_QUAD_IN(r) & ~(v)))
 106
 107 /* virtual addresses for the above */
 108 static volatile u8 __iomem *hhead_base;
 109 static volatile u8 __iomem *quad_base;
 110 static volatile u32 __iomem *psurge_pri_intr;
 111 static volatile u8 __iomem *psurge_sec_intr;
 112 static volatile u32 __iomem *psurge_start;
 113
 114 /* values for psurge_type */
 115 #define PSURGE_NONE             -1
 116 #define PSURGE_DUAL             0
 117 #define PSURGE_QUAD_OKEE        1
 118 #define PSURGE_QUAD_COTTON      2
 119 #define PSURGE_QUAD_ICEGRASS    3
 120
 121 /* what sort of powersurge board we have */
 122 static int psurge_type = PSURGE_NONE;
 123
 124 /* irq for secondary cpus to report */
 125 static struct irq_domain *psurge_host;
 126 int psurge_secondary_virq;
 127
 128 /*
 129  * Set and clear IPIs for powersurge.
 130  */
 131 static inline void psurge_set_ipi(int cpu)
 132 {
 133         if (psurge_type == PSURGE_NONE)
 134                 return;
 135         if (cpu == 0)
 136                 in_be32(psurge_pri_intr);
 137         else if (psurge_type == PSURGE_DUAL)
 138                 out_8(psurge_sec_intr, 0);
 139         else
 140                 PSURGE_QUAD_OUT(PSURGE_QUAD_IRQ_SET, 1 << cpu);
 141 }
 142
 143 static inline void psurge_clr_ipi(int cpu)
 144 {
 145         if (cpu > 0) {
 146                 switch(psurge_type) {
 147                 case PSURGE_DUAL:
 148                         out_8(psurge_sec_intr, ~0);
 149                 case PSURGE_NONE:
 150                         break;
 151                 default:
 152                         PSURGE_QUAD_OUT(PSURGE_QUAD_IRQ_CLR, 1 << cpu);
 153                 }
 154         }
 155 }
 156
 157 /*
 158  * On powersurge (old SMP powermac architecture) we don't have
 159  * separate IPIs for separate messages like openpic does.  Instead
 160  * use the generic demux helpers
 161  *  -- paulus.
 162  */
 163 static irqreturn_t psurge_ipi_intr(int irq, void *d)
 164 {
 165         psurge_clr_ipi(smp_processor_id());
 166         smp_ipi_demux();
 167
 168         return IRQ_HANDLED;
 169 }
 170
 171 static void smp_psurge_cause_ipi(int cpu)
 172 {
 173         psurge_set_ipi(cpu);
 174 }
 175
 176 static int psurge_host_map(struct irq_domain *h, unsigned int virq,
 177                          irq_hw_number_t hw)
 178 {
 179         irq_set_chip_and_handler(virq, &dummy_irq_chip, handle_percpu_irq);
 180
 181         return 0;
 182 }
 183
 184 static const struct irq_domain_ops psurge_host_ops = {
 185         .map    = psurge_host_map,
 186 };
 187
 188 static int psurge_secondary_ipi_init(void)
 189 {
 190         int rc = -ENOMEM;
 191
 192         psurge_host = irq_domain_add_nomap(NULL, ~0, &psurge_host_ops, NULL);
 193
 194         if (psurge_host)
 195                 psurge_secondary_virq = irq_create_direct_mapping(psurge_host);
 196
 197         if (psurge_secondary_virq)
 198                 rc = request_irq(psurge_secondary_virq, psurge_ipi_intr,
 199                         IRQF_PERCPU | IRQF_NO_THREAD, "IPI", NULL);
 200
 201         if (rc)
 202                 pr_err("Failed to setup secondary cpu IPI\n");
 203
 204         return rc;
 205 }
 206
 207 /*
 208  * Determine a quad card presence. We read the board ID register, we
 209  * force the data bus to change to something else, and we read it again.
 210  * It it's stable, then the register probably exist (ugh !)
 211  */
 212 static int __init psurge_quad_probe(void)
 213 {
 214         int type;
 215         unsigned int i;
 216
 217         type = PSURGE_QUAD_IN(PSURGE_QUAD_BOARD_ID);
 218         if (type < PSURGE_QUAD_OKEE || type > PSURGE_QUAD_ICEGRASS
 219             || type != PSURGE_QUAD_IN(PSURGE_QUAD_BOARD_ID))
 220                 return PSURGE_DUAL;
 221
 222         /* looks OK, try a slightly more rigorous test */
 223         /* bogus is not necessarily cacheline-aligned,
 224            though I don't suppose that really matters.  -- paulus */
 225         for (i = 0; i < 100; i++) {
 226                 volatile u32 bogus[8];
 227                 bogus[(0+i)%8] = 0x00000000;
 228                 bogus[(1+i)%8] = 0x55555555;
 229                 bogus[(2+i)%8] = 0xFFFFFFFF;
 230                 bogus[(3+i)%8] = 0xAAAAAAAA;
 231                 bogus[(4+i)%8] = 0x33333333;
 232                 bogus[(5+i)%8] = 0xCCCCCCCC;
 233                 bogus[(6+i)%8] = 0xCCCCCCCC;
 234                 bogus[(7+i)%8] = 0x33333333;
 235                 wmb();
 236                 asm volatile("dcbf 0,%0" : : "r" (bogus) : "memory");
 237                 mb();
 238                 if (type != PSURGE_QUAD_IN(PSURGE_QUAD_BOARD_ID))
 239                         return PSURGE_DUAL;
 240         }
 241         return type;
 242 }
 243
 244 static void __init psurge_quad_init(void)
 245 {
 246         int procbits;
 247
 248         if (ppc_md.progress) ppc_md.progress("psurge_quad_init", 0x351);
 249         procbits = ~PSURGE_QUAD_IN(PSURGE_QUAD_WHICH_CPU);
 250         if (psurge_type == PSURGE_QUAD_ICEGRASS)
 251                 PSURGE_QUAD_BIS(PSURGE_QUAD_RESET_CTL, procbits);
 252         else
 253                 PSURGE_QUAD_BIC(PSURGE_QUAD_CKSTOP_CTL, procbits);
 254         mdelay(33);
 255         out_8(psurge_sec_intr, ~0);
 256         PSURGE_QUAD_OUT(PSURGE_QUAD_IRQ_CLR, procbits);
 257         PSURGE_QUAD_BIS(PSURGE_QUAD_RESET_CTL, procbits);
 258         if (psurge_type != PSURGE_QUAD_ICEGRASS)
 259                 PSURGE_QUAD_BIS(PSURGE_QUAD_CKSTOP_CTL, procbits);
 260         PSURGE_QUAD_BIC(PSURGE_QUAD_PRIMARY_ARB, procbits);
 261         mdelay(33);
 262         PSURGE_QUAD_BIC(PSURGE_QUAD_RESET_CTL, procbits);
 263         mdelay(33);
 264         PSURGE_QUAD_BIS(PSURGE_QUAD_PRIMARY_ARB, procbits);
 265         mdelay(33);
 266 }
 267
 268 static void __init smp_psurge_probe(void)
 269 {
 270         int i, ncpus;
 271         struct device_node *dn;
 272
 273         /* We don't do SMP on the PPC601 -- paulus */
 274         if (PVR_VER(mfspr(SPRN_PVR)) == 1)
 275                 return;
 276
 277         /*
 278          * The powersurge cpu board can be used in the generation
 279          * of powermacs that have a socket for an upgradeable cpu card,
 280          * including the 7500, 8500, 9500, 9600.
 281          * The device tree doesn't tell you if you have 2 cpus because
 282          * OF doesn't know anything about the 2nd processor.
 283          * Instead we look for magic bits in magic registers,
 284          * in the hammerhead memory controller in the case of the
 285          * dual-cpu powersurge board.  -- paulus.
 286          */
 287         dn = of_find_node_by_name(NULL, "hammerhead");
 288         if (dn == NULL)
 289                 return;
 290         of_node_put(dn);
 291
 292         hhead_base = ioremap(HAMMERHEAD_BASE, 0x800);
 293         quad_base = ioremap(PSURGE_QUAD_REG_ADDR, 1024);
 294         psurge_sec_intr = hhead_base + HHEAD_SEC_INTR;
 295
 296         psurge_type = psurge_quad_probe();
 297         if (psurge_type != PSURGE_DUAL) {
 298                 psurge_quad_init();
 299                 /* All released cards using this HW design have 4 CPUs */
 300                 ncpus = 4;
 301                 /* No sure how timebase sync works on those, let's use SW */
 302                 smp_ops->give_timebase = smp_generic_give_timebase;
 303                 smp_ops->take_timebase = smp_generic_take_timebase;
 304         } else {
 305                 iounmap(quad_base);
 306                 if ((in_8(hhead_base + HHEAD_CONFIG) & 0x02) == 0) {
 307                         /* not a dual-cpu card */
 308                         iounmap(hhead_base);
 309                         psurge_type = PSURGE_NONE;
 310                         return;
 311                 }
 312                 ncpus = 2;
 313         }
 314
 315         if (psurge_secondary_ipi_init())
 316                 return;
 317
 318         psurge_start = ioremap(PSURGE_START, 4);
 319         psurge_pri_intr = ioremap(PSURGE_PRI_INTR, 4);
 320
 321         /* This is necessary because OF doesn't know about the
 322          * secondary cpu(s), and thus there aren't nodes in the
 323          * device tree for them, and smp_setup_cpu_maps hasn't
 324          * set their bits in cpu_present_mask.
 325          */
 326         if (ncpus > NR_CPUS)
 327                 ncpus = NR_CPUS;
 328         for (i = 1; i < ncpus ; ++i)
 329                 set_cpu_present(i, true);
 330
 331         if (ppc_md.progress) ppc_md.progress("smp_psurge_probe - done", 0x352);
 332 }
 333
 334 static int __init smp_psurge_kick_cpu(int nr)
 335 {
 336         unsigned long start = __pa(__secondary_start_pmac_0) + nr * 8;
 337         unsigned long a, flags;
 338         int i, j;
 339
 340         /* Defining this here is evil ... but I prefer hiding that
 341          * crap to avoid giving people ideas that they can do the
 342          * same.
 343          */
 344         extern volatile unsigned int cpu_callin_map[NR_CPUS];
 345
 346         /* may need to flush here if secondary bats aren't setup */
 347         for (a = KERNELBASE; a < KERNELBASE + 0x800000; a += 32)
 348                 asm volatile("dcbf 0,%0" : : "r" (a) : "memory");
 349         asm volatile("sync");
 350
 351         if (ppc_md.progress) ppc_md.progress("smp_psurge_kick_cpu", 0x353);
 352
 353         /* This is going to freeze the timeebase, we disable interrupts */
 354         local_irq_save(flags);
 355
 356         out_be32(psurge_start, start);
 357         mb();
 358
 359         psurge_set_ipi(nr);
 360
 361         /*
 362          * We can't use udelay here because the timebase is now frozen.
 363          */
 364         for (i = 0; i < 2000; ++i)
 365                 asm volatile("nop" : : : "memory");
 366         psurge_clr_ipi(nr);
 367
 368         /*
 369          * Also, because the timebase is frozen, we must not return to the
 370          * caller which will try to do udelay's etc... Instead, we wait -here-
 371          * for the CPU to callin.
 372          */
 373         for (i = 0; i < 100000 && !cpu_callin_map[nr]; ++i) {
 374                 for (j = 1; j < 10000; j++)
 375                         asm volatile("nop" : : : "memory");
 376                 asm volatile("sync" : : : "memory");
 377         }
 378         if (!cpu_callin_map[nr])
 379                 goto stuck;
 380
 381         /* And we do the TB sync here too for standard dual CPU cards */
 382         if (psurge_type == PSURGE_DUAL) {
 383                 while(!tb_req)
 384                         barrier();
 385                 tb_req = 0;
 386                 mb();
 387                 timebase = get_tb();
 388                 mb();
 389                 while (timebase)
 390                         barrier();
 391                 mb();
 392         }
 393  stuck:
 394         /* now interrupt the secondary, restarting both TBs */
 395         if (psurge_type == PSURGE_DUAL)
 396                 psurge_set_ipi(1);
 397
 398         if (ppc_md.progress) ppc_md.progress("smp_psurge_kick_cpu - done", 0x354);
 399
 400         return 0;
 401 }
 402
 403 static void __init smp_psurge_setup_cpu(int cpu_nr)
 404 {
 405         unsigned long flags = IRQF_PERCPU | IRQF_NO_THREAD;
 406         int irq;
 407
 408         if (cpu_nr != 0 || !psurge_start)
 409                 return;
 410
 411         /* reset the entry point so if we get another intr we won't
 412          * try to startup again */
 413         out_be32(psurge_start, 0x100);
 414         irq = irq_create_mapping(NULL, 30);
 415         if (request_irq(irq, psurge_ipi_intr, flags, "primary IPI", NULL))
 416                 printk(KERN_ERR "Couldn't get primary IPI interrupt");
 417 }
 418
 419 void __init smp_psurge_take_timebase(void)
 420 {
 421         if (psurge_type != PSURGE_DUAL)
 422                 return;
 423
 424         tb_req = 1;
 425         mb();
 426         while (!timebase)
 427                 barrier();
 428         mb();
 429         set_tb(timebase >> 32, timebase & 0xffffffff);
 430         timebase = 0;
 431         mb();
 432         set_dec(tb_ticks_per_jiffy/2);
 433 }
 434
 435 void __init smp_psurge_give_timebase(void)
 436 {
 437         /* Nothing to do here */
 438 }
 439
 440 /* PowerSurge-style Macs */
 441 struct smp_ops_t psurge_smp_ops = {
 442         .message_pass   = NULL, /* Use smp_muxed_ipi_message_pass */
 443         .cause_ipi      = smp_psurge_cause_ipi,
 444         .cause_nmi_ipi  = NULL,
 445         .probe          = smp_psurge_probe,
 446         .kick_cpu       = smp_psurge_kick_cpu,
 447         .setup_cpu      = smp_psurge_setup_cpu,
 448         .give_timebase  = smp_psurge_give_timebase,
 449         .take_timebase  = smp_psurge_take_timebase,
 450 };
 451 #endif /* CONFIG_PPC_PMAC32_PSURGE */
 452
 453 /*
 454  * Core 99 and later support
 455  */
 456
 457
 458 static void smp_core99_give_timebase(void)
 459 {
 460         unsigned long flags;
 461
 462         local_irq_save(flags);
 463
 464         while(!tb_req)
 465                 barrier();
 466         tb_req = 0;
 467         (*pmac_tb_freeze)(1);
 468         mb();
 469         timebase = get_tb();
 470         mb();
 471         while (timebase)
 472                 barrier();
 473         mb();
 474         (*pmac_tb_freeze)(0);
 475         mb();
 476
 477         local_irq_restore(flags);
 478 }
 479
 480
 481 static void smp_core99_take_timebase(void)
 482 {
 483         unsigned long flags;
 484
 485         local_irq_save(flags);
 486
 487         tb_req = 1;
 488         mb();
 489         while (!timebase)
 490                 barrier();
 491         mb();
 492         set_tb(timebase >> 32, timebase & 0xffffffff);
 493         timebase = 0;
 494         mb();
 495
 496         local_irq_restore(flags);
 497 }
 498
 499 #ifdef CONFIG_PPC64
 500 /*
 501  * G5s enable/disable the timebase via an i2c-connected clock chip.
 502  */
 503 static struct pmac_i2c_bus *pmac_tb_clock_chip_host;
 504 static u8 pmac_tb_pulsar_addr;
 505
 506 static void smp_core99_cypress_tb_freeze(int freeze)
 507 {
 508         u8 data;
 509         int rc;
 510
 511         /* Strangely, the device-tree says address is 0xd2, but darwin
 512          * accesses 0xd0 ...
 513          */
 514         pmac_i2c_setmode(pmac_tb_clock_chip_host,
 515                          pmac_i2c_mode_combined);
 516         rc = pmac_i2c_xfer(pmac_tb_clock_chip_host,
 517                            0xd0 | pmac_i2c_read,
 518                            1, 0x81, &data, 1);
 519         if (rc != 0)
 520                 goto bail;
 521
 522         data = (data & 0xf3) | (freeze ? 0x00 : 0x0c);
 523
 524         pmac_i2c_setmode(pmac_tb_clock_chip_host, pmac_i2c_mode_stdsub);
 525         rc = pmac_i2c_xfer(pmac_tb_clock_chip_host,
 526                            0xd0 | pmac_i2c_write,
 527                            1, 0x81, &data, 1);
 528
 529  bail:
 530         if (rc != 0) {
 531                 printk("Cypress Timebase %s rc: %d\n",
 532                        freeze ? "freeze" : "unfreeze", rc);
 533                 panic("Timebase freeze failed !\n");
 534         }
 535 }
 536
 537
 538 static void smp_core99_pulsar_tb_freeze(int freeze)
 539 {
 540         u8 data;
 541         int rc;
 542
 543         pmac_i2c_setmode(pmac_tb_clock_chip_host,
 544                          pmac_i2c_mode_combined);
 545         rc = pmac_i2c_xfer(pmac_tb_clock_chip_host,
 546                            pmac_tb_pulsar_addr | pmac_i2c_read,
 547                            1, 0x2e, &data, 1);
 548         if (rc != 0)
 549                 goto bail;
 550
 551         data = (data & 0x88) | (freeze ? 0x11 : 0x22);
 552
 553         pmac_i2c_setmode(pmac_tb_clock_chip_host, pmac_i2c_mode_stdsub);
 554         rc = pmac_i2c_xfer(pmac_tb_clock_chip_host,
 555                            pmac_tb_pulsar_addr | pmac_i2c_write,
 556                            1, 0x2e, &data, 1);
 557  bail:
 558         if (rc != 0) {
 559                 printk(KERN_ERR "Pulsar Timebase %s rc: %d\n",
 560                        freeze ? "freeze" : "unfreeze", rc);
 561                 panic("Timebase freeze failed !\n");
 562         }
 563 }
 564
 565 static void __init smp_core99_setup_i2c_hwsync(int ncpus)
 566 {
 567         struct device_node *cc = NULL;
 568         struct device_node *p;
 569         const char *name = NULL;
 570         const u32 *reg;
 571         int ok;
 572
 573         /* Look for the clock chip */
 574         for_each_node_by_name(cc, "i2c-hwclock") {
 575                 p = of_get_parent(cc);
 576                 ok = p && of_device_is_compatible(p, "uni-n-i2c");
 577                 of_node_put(p);
 578                 if (!ok)
 579                         continue;
 580
 581                 pmac_tb_clock_chip_host = pmac_i2c_find_bus(cc);
 582                 if (pmac_tb_clock_chip_host == NULL)
 583                         continue;
 584                 reg = of_get_property(cc, "reg", NULL);
 585                 if (reg == NULL)
 586                         continue;
 587                 switch (*reg) {
 588                 case 0xd2:
 589                         if (of_device_is_compatible(cc,"pulsar-legacy-slewing")) {
 590                                 pmac_tb_freeze = smp_core99_pulsar_tb_freeze;
 591                                 pmac_tb_pulsar_addr = 0xd2;
 592                                 name = "Pulsar";
 593                         } else if (of_device_is_compatible(cc, "cy28508")) {
 594                                 pmac_tb_freeze = smp_core99_cypress_tb_freeze;
 595                                 name = "Cypress";
 596                         }
 597                         break;
 598                 case 0xd4:
 599                         pmac_tb_freeze = smp_core99_pulsar_tb_freeze;
 600                         pmac_tb_pulsar_addr = 0xd4;
 601                         name = "Pulsar";
 602                         break;
 603                 }
 604                 if (pmac_tb_freeze != NULL)
 605                         break;
 606         }
 607         if (pmac_tb_freeze != NULL) {
 608                 /* Open i2c bus for synchronous access */
 609                 if (pmac_i2c_open(pmac_tb_clock_chip_host, 1)) {
 610                         printk(KERN_ERR "Failed top open i2c bus for clock"
 611                                " sync, fallback to software sync !\n");
 612                         goto no_i2c_sync;
 613                 }
 614                 printk(KERN_INFO "Processor timebase sync using %s i2c clock\n",
 615                        name);
 616                 return;
 617         }
 618  no_i2c_sync:
 619         pmac_tb_freeze = NULL;
 620         pmac_tb_clock_chip_host = NULL;
 621 }
 622
 623
 624
 625 /*
 626  * Newer G5s uses a platform function
 627  */
 628
 629 static void smp_core99_pfunc_tb_freeze(int freeze)
 630 {
 631         struct device_node *cpus;
 632         struct pmf_args args;
 633
 634         cpus = of_find_node_by_path("/cpus");
 635         BUG_ON(cpus == NULL);
 636         args.count = 1;
 637         args.u[0].v = !freeze;
 638         pmf_call_function(cpus, "cpu-timebase", &args);
 639         of_node_put(cpus);
 640 }
 641
 642 #else /* CONFIG_PPC64 */
 643
 644 /*
 645  * SMP G4 use a GPIO to enable/disable the timebase.
 646  */
 647
 648 static unsigned int core99_tb_gpio;     /* Timebase freeze GPIO */
 649
 650 static void smp_core99_gpio_tb_freeze(int freeze)
 651 {
 652         if (freeze)
 653                 pmac_call_feature(PMAC_FTR_WRITE_GPIO, NULL, core99_tb_gpio, 4);
 654         else
 655                 pmac_call_feature(PMAC_FTR_WRITE_GPIO, NULL, core99_tb_gpio, 0);
 656         pmac_call_feature(PMAC_FTR_READ_GPIO, NULL, core99_tb_gpio, 0);
 657 }
 658
 659
 660 #endif /* !CONFIG_PPC64 */
 661
 662 static void core99_init_caches(int cpu)
 663 {
 664 #ifndef CONFIG_PPC64
 665         /* L2 and L3 cache settings to pass from CPU0 to CPU1 on G4 cpus */
 666         static long int core99_l2_cache;
 667         static long int core99_l3_cache;
 668
 669         if (!cpu_has_feature(CPU_FTR_L2CR))
 670                 return;
 671
 672         if (cpu == 0) {
 673                 core99_l2_cache = _get_L2CR();
 674                 printk("CPU0: L2CR is %lx\n", core99_l2_cache);
 675         } else {
 676                 printk("CPU%d: L2CR was %lx\n", cpu, _get_L2CR());
 677                 _set_L2CR(0);
 678                 _set_L2CR(core99_l2_cache);
 679                 printk("CPU%d: L2CR set to %lx\n", cpu, core99_l2_cache);
 680         }
 681
 682         if (!cpu_has_feature(CPU_FTR_L3CR))
 683                 return;
 684
 685         if (cpu == 0){
 686                 core99_l3_cache = _get_L3CR();
 687                 printk("CPU0: L3CR is %lx\n", core99_l3_cache);
 688         } else {
 689                 printk("CPU%d: L3CR was %lx\n", cpu, _get_L3CR());
 690                 _set_L3CR(0);
 691                 _set_L3CR(core99_l3_cache);
 692                 printk("CPU%d: L3CR set to %lx\n", cpu, core99_l3_cache);
 693         }
 694 #endif /* !CONFIG_PPC64 */
 695 }
 696
 697 static void __init smp_core99_setup(int ncpus)
 698 {
 699 #ifdef CONFIG_PPC64
 700
 701         /* i2c based HW sync on some G5s */
 702         if (of_machine_is_compatible("PowerMac7,2") ||
 703             of_machine_is_compatible("PowerMac7,3") ||
 704             of_machine_is_compatible("RackMac3,1"))
 705                 smp_core99_setup_i2c_hwsync(ncpus);
 706
 707         /* pfunc based HW sync on recent G5s */
 708         if (pmac_tb_freeze == NULL) {
 709                 struct device_node *cpus =
 710                         of_find_node_by_path("/cpus");
 711                 if (cpus &&
 712                     of_get_property(cpus, "platform-cpu-timebase", NULL)) {
 713                         pmac_tb_freeze = smp_core99_pfunc_tb_freeze;
 714                         printk(KERN_INFO "Processor timebase sync using"
 715                                " platform function\n");
 716                 }
 717         }
 718
 719 #else /* CONFIG_PPC64 */
 720
 721         /* GPIO based HW sync on ppc32 Core99 */
 722         if (pmac_tb_freeze == NULL && !of_machine_is_compatible("MacRISC4")) {
 723                 struct device_node *cpu;
 724                 const u32 *tbprop = NULL;
 725
 726                 core99_tb_gpio = KL_GPIO_TB_ENABLE;     /* default value */
 727                 cpu = of_find_node_by_type(NULL, "cpu");
 728                 if (cpu != NULL) {
 729                         tbprop = of_get_property(cpu, "timebase-enable", NULL);
 730                         if (tbprop)
 731                                 core99_tb_gpio = *tbprop;
 732                         of_node_put(cpu);
 733                 }
 734                 pmac_tb_freeze = smp_core99_gpio_tb_freeze;
 735                 printk(KERN_INFO "Processor timebase sync using"
 736                        " GPIO 0x%02x\n", core99_tb_gpio);
 737         }
 738
 739 #endif /* CONFIG_PPC64 */
 740
 741         /* No timebase sync, fallback to software */
 742         if (pmac_tb_freeze == NULL) {
 743                 smp_ops->give_timebase = smp_generic_give_timebase;
 744                 smp_ops->take_timebase = smp_generic_take_timebase;
 745                 printk(KERN_INFO "Processor timebase sync using software\n");
 746         }
 747
 748 #ifndef CONFIG_PPC64
 749         {
 750                 int i;
 751
 752                 /* XXX should get this from reg properties */
 753                 for (i = 1; i < ncpus; ++i)
 754                         set_hard_smp_processor_id(i, i);
 755         }
 756 #endif
 757
 758         /* 32 bits SMP can't NAP */
 759         if (!of_machine_is_compatible("MacRISC4"))
 760                 powersave_nap = 0;
 761 }
 762
 763 static void __init smp_core99_probe(void)
 764 {
 765         struct device_node *cpus;
 766         int ncpus = 0;
 767
 768         if (ppc_md.progress) ppc_md.progress("smp_core99_probe", 0x345);
 769
 770         /* Count CPUs in the device-tree */
 771         for_each_node_by_type(cpus, "cpu")
 772                 ++ncpus;
 773
 774         printk(KERN_INFO "PowerMac SMP probe found %d cpus\n", ncpus);
 775
 776         /* Nothing more to do if less than 2 of them */
 777         if (ncpus <= 1)
 778                 return;
 779
 780         /* We need to perform some early initialisations before we can start
 781          * setting up SMP as we are running before initcalls
 782          */
 783         pmac_pfunc_base_install();
 784         pmac_i2c_init();
 785
 786         /* Setup various bits like timebase sync method, ability to nap, ... */
 787         smp_core99_setup(ncpus);
 788
 789         /* Install IPIs */
 790         mpic_request_ipis();
 791
 792         /* Collect l2cr and l3cr values from CPU 0 */
 793         core99_init_caches(0);
 794 }
 795
 796 static int smp_core99_kick_cpu(int nr)
 797 {
 798         unsigned int save_vector;
 799         unsigned long target, flags;
 800         unsigned int *vector = (unsigned int *)(PAGE_OFFSET+0x100);
 801
 802         if (nr < 0 || nr > 3)
 803                 return -ENOENT;
 804
 805         if (ppc_md.progress)
 806                 ppc_md.progress("smp_core99_kick_cpu", 0x346);
 807
 808         local_irq_save(flags);
 809
 810         /* Save reset vector */
 811         save_vector = *vector;
 812
 813         /* Setup fake reset vector that does
 814          *   b __secondary_start_pmac_0 + nr*8
 815          */
 816         target = (unsigned long) __secondary_start_pmac_0 + nr * 8;
 817         patch_branch((struct ppc_inst *)vector, target, BRANCH_SET_LINK);
 818
 819         /* Put some life in our friend */
 820         pmac_call_feature(PMAC_FTR_RESET_CPU, NULL, nr, 0);
 821
 822         /* FIXME: We wait a bit for the CPU to take the exception, I should
 823          * instead wait for the entry code to set something for me. Well,
 824          * ideally, all that crap will be done in prom.c and the CPU left
 825          * in a RAM-based wait loop like CHRP.
 826          */
 827         mdelay(1);
 828
 829         /* Restore our exception vector */
 830         patch_instruction((struct ppc_inst *)vector, ppc_inst(save_vector));
 831
 832         local_irq_restore(flags);
 833         if (ppc_md.progress) ppc_md.progress("smp_core99_kick_cpu done", 0x347);
 834
 835         return 0;
 836 }
 837
 838 static void smp_core99_setup_cpu(int cpu_nr)
 839 {
 840         /* Setup L2/L3 */
 841         if (cpu_nr != 0)
 842                 core99_init_caches(cpu_nr);
 843
 844         /* Setup openpic */
 845         mpic_setup_this_cpu();
 846 }
 847
 848 #ifdef CONFIG_PPC64
 849 #ifdef CONFIG_HOTPLUG_CPU
 850 static unsigned int smp_core99_host_open;
 851
 852 static int smp_core99_cpu_prepare(unsigned int cpu)
 853 {
 854         int rc;
 855
 856         /* Open i2c bus if it was used for tb sync */
 857         if (pmac_tb_clock_chip_host && !smp_core99_host_open) {
 858                 rc = pmac_i2c_open(pmac_tb_clock_chip_host, 1);
 859                 if (rc) {
 860                         pr_err("Failed to open i2c bus for time sync\n");
 861                         return notifier_from_errno(rc);
 862                 }
 863                 smp_core99_host_open = 1;
 864         }
 865         return 0;
 866 }
 867
 868 static int smp_core99_cpu_online(unsigned int cpu)
 869 {
 870         /* Close i2c bus if it was used for tb sync */
 871         if (pmac_tb_clock_chip_host && smp_core99_host_open) {
 872                 pmac_i2c_close(pmac_tb_clock_chip_host);
 873                 smp_core99_host_open = 0;
 874         }
 875         return 0;
 876 }
 877 #endif /* CONFIG_HOTPLUG_CPU */
 878
 879 static void __init smp_core99_bringup_done(void)
 880 {
 881         extern void g5_phy_disable_cpu1(void);
 882
 883         /* Close i2c bus if it was used for tb sync */
 884         if (pmac_tb_clock_chip_host)
 885                 pmac_i2c_close(pmac_tb_clock_chip_host);
 886
 887         /* If we didn't start the second CPU, we must take
 888          * it off the bus.
 889          */
 890         if (of_machine_is_compatible("MacRISC4") &&
 891             num_online_cpus() < 2) {
 892                 set_cpu_present(1, false);
 893                 g5_phy_disable_cpu1();
 894         }
 895 #ifdef CONFIG_HOTPLUG_CPU
 896         cpuhp_setup_state_nocalls(CPUHP_POWERPC_PMAC_PREPARE,
 897                                   "powerpc/pmac:prepare", smp_core99_cpu_prepare,
 898                                   NULL);
 899         cpuhp_setup_state_nocalls(CPUHP_AP_ONLINE_DYN, "powerpc/pmac:online",
 900                                   smp_core99_cpu_online, NULL);
 901 #endif
 902
 903         if (ppc_md.progress)
 904                 ppc_md.progress("smp_core99_bringup_done", 0x349);
 905 }
 906 #endif /* CONFIG_PPC64 */
 907
 908 #ifdef CONFIG_HOTPLUG_CPU
 909
 910 static int smp_core99_cpu_disable(void)
 911 {
 912         int rc = generic_cpu_disable();
 913         if (rc)
 914                 return rc;
 915
 916         mpic_cpu_set_priority(0xf);
 917
 918         return 0;
 919 }
 920
 921 #ifdef CONFIG_PPC32
 922
 923 static void pmac_cpu_die(void)
 924 {
 925         int cpu = smp_processor_id();
 926
 927         local_irq_disable();
 928         idle_task_exit();
 929         pr_debug("CPU%d offline\n", cpu);
 930         generic_set_cpu_dead(cpu);
 931         smp_wmb();
 932         mb();
 933         low_cpu_die();
 934 }
 935
 936 #else /* CONFIG_PPC32 */
 937
 938 static void pmac_cpu_die(void)
 939 {
 940         int cpu = smp_processor_id();
 941
 942         local_irq_disable();
 943         idle_task_exit();
 944
 945         /*
 946          * turn off as much as possible, we'll be
 947          * kicked out as this will only be invoked
 948          * on core99 platforms for now ...
 949          */
 950
 951         printk(KERN_INFO "CPU#%d offline\n", cpu);
 952         generic_set_cpu_dead(cpu);
 953         smp_wmb();
 954
 955         /*
 956          * Re-enable interrupts. The NAP code needs to enable them
 957          * anyways, do it now so we deal with the case where one already
 958          * happened while soft-disabled.
 959          * We shouldn't get any external interrupts, only decrementer, and the
 960          * decrementer handler is safe for use on offline CPUs
 961          */
 962         local_irq_enable();
 963
 964         while (1) {
 965                 /* let's not take timer interrupts too often ... */
 966                 set_dec(0x7fffffff);
 967
 968                 /* Enter NAP mode */
 969                 power4_idle();
 970         }
 971 }
 972
 973 #endif /* else CONFIG_PPC32 */
 974 #endif /* CONFIG_HOTPLUG_CPU */
 975
 976 /* Core99 Macs (dual G4s and G5s) */
 977 static struct smp_ops_t core99_smp_ops = {
 978         .message_pass   = smp_mpic_message_pass,
 979         .probe          = smp_core99_probe,
 980 #ifdef CONFIG_PPC64
 981         .bringup_done   = smp_core99_bringup_done,
 982 #endif
 983         .kick_cpu       = smp_core99_kick_cpu,
 984         .setup_cpu      = smp_core99_setup_cpu,
 985         .give_timebase  = smp_core99_give_timebase,
 986         .take_timebase  = smp_core99_take_timebase,
 987 #if defined(CONFIG_HOTPLUG_CPU)
 988         .cpu_disable    = smp_core99_cpu_disable,
 989         .cpu_die        = generic_cpu_die,
 990 #endif
 991 };
 992
 993 void __init pmac_setup_smp(void)
 994 {
 995         struct device_node *np;
 996
 997         /* Check for Core99 */
 998         np = of_find_node_by_name(NULL, "uni-n");
 999         if (!np)
1000                 np = of_find_node_by_name(NULL, "u3");
1001         if (!np)
1002                 np = of_find_node_by_name(NULL, "u4");
1003         if (np) {
1004                 of_node_put(np);
1005                 smp_ops = &core99_smp_ops;
1006         }
1007 #ifdef CONFIG_PPC_PMAC32_PSURGE
1008         else {
1009                 /* We have to set bits in cpu_possible_mask here since the
1010                  * secondary CPU(s) aren't in the device tree. Various
1011                  * things won't be initialized for CPUs not in the possible
1012                  * map, so we really need to fix it up here.
1013                  */
1014                 int cpu;
1015
1016                 for (cpu = 1; cpu < 4 && cpu < NR_CPUS; ++cpu)
1017                         set_cpu_possible(cpu, true);
1018                 smp_ops = &psurge_smp_ops;
1019         }
1020 #endif /* CONFIG_PPC_PMAC32_PSURGE */
1021
1022 #ifdef CONFIG_HOTPLUG_CPU
1023         ppc_md.cpu_die = pmac_cpu_die;
1024 #endif
1025 }
1026
1027