arch/arm64/boot/dts/qcom/sa8775p-ride.dts

   1 // SPDX-License-Identifier: BSD-3-Clause
   2 /*
   3  * Copyright (c) 2023, Linaro Limited
   4  */
   5
   6 /dts-v1/;
   7
   8 #include <dt-bindings/gpio/gpio.h>
   9 #include <dt-bindings/regulator/qcom,rpmh-regulator.h>
  10
  11 #include "sa8775p.dtsi"
  12 #include "sa8775p-pmics.dtsi"
  13
  14 / {
  15         model = "Qualcomm SA8775P Ride";
  16         compatible = "qcom,sa8775p-ride", "qcom,sa8775p";
  17
  18         aliases {
  19                 ethernet0 = &ethernet0;
  20                 ethernet1 = &ethernet1;
  21                 i2c11 = &i2c11;
  22                 i2c18 = &i2c18;
  23                 serial0 = &uart10;
  24                 serial1 = &uart12;
  25                 serial2 = &uart17;
  26                 spi16 = &spi16;
  27                 ufshc1 = &ufs_mem_hc;
  28         };
  29
  30         chosen {
  31                 stdout-path = "serial0:115200n8";
  32         };
  33 };
  34
  35 &apps_rsc {
  36         regulators-0 {
  37                 compatible = "qcom,pmm8654au-rpmh-regulators";
  38                 qcom,pmic-id = "a";
  39
  40                 vreg_s4a: smps4 {
  41                         regulator-name = "vreg_s4a";
  42                         regulator-min-microvolt = <1800000>;
  43                         regulator-max-microvolt = <1816000>;
  44                         regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>;
  45                 };
  46
  47                 vreg_s5a: smps5 {
  48                         regulator-name = "vreg_s5a";
  49                         regulator-min-microvolt = <1850000>;
  50                         regulator-max-microvolt = <1996000>;
  51                         regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>;
  52                 };
  53
  54                 vreg_s9a: smps9 {
  55                         regulator-name = "vreg_s9a";
  56                         regulator-min-microvolt = <535000>;
  57                         regulator-max-microvolt = <1120000>;
  58                         regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>;
  59                 };
  60
  61                 vreg_l4a: ldo4 {
  62                         regulator-name = "vreg_l4a";
  63                         regulator-min-microvolt = <788000>;
  64                         regulator-max-microvolt = <1050000>;
  65                         regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>;
  66                         regulator-allow-set-load;
  67                         regulator-allowed-modes = <RPMH_REGULATOR_MODE_LPM
  68                                                    RPMH_REGULATOR_MODE_HPM>;
  69                 };
  70
  71                 vreg_l5a: ldo5 {
  72                         regulator-name = "vreg_l5a";
  73                         regulator-min-microvolt = <870000>;
  74                         regulator-max-microvolt = <950000>;
  75                         regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>;
  76                         regulator-allow-set-load;
  77                         regulator-allowed-modes = <RPMH_REGULATOR_MODE_LPM
  78                                                    RPMH_REGULATOR_MODE_HPM>;
  79                 };
  80
  81                 vreg_l6a: ldo6 {
  82                         regulator-name = "vreg_l6a";
  83                         regulator-min-microvolt = <870000>;
  84                         regulator-max-microvolt = <970000>;
  85                         regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>;
  86                         regulator-allow-set-load;
  87                         regulator-allowed-modes = <RPMH_REGULATOR_MODE_LPM
  88                                                    RPMH_REGULATOR_MODE_HPM>;
  89                 };
  90
  91                 vreg_l7a: ldo7 {
  92                         regulator-name = "vreg_l7a";
  93                         regulator-min-microvolt = <720000>;
  94                         regulator-max-microvolt = <950000>;
  95                         regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>;
  96                         regulator-allow-set-load;
  97                         regulator-allowed-modes = <RPMH_REGULATOR_MODE_LPM
  98                                                    RPMH_REGULATOR_MODE_HPM>;
  99                 };
 100
 101                 vreg_l8a: ldo8 {
 102                         regulator-name = "vreg_l8a";
 103                         regulator-min-microvolt = <2504000>;
 104                         regulator-max-microvolt = <3300000>;
 105                         regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>;
 106                         regulator-allow-set-load;
 107                         regulator-allowed-modes = <RPMH_REGULATOR_MODE_LPM
 108                                                    RPMH_REGULATOR_MODE_HPM>;
 109                 };
 110
 111                 vreg_l9a: ldo9 {
 112                         regulator-name = "vreg_l9a";
 113                         regulator-min-microvolt = <2970000>;
 114                         regulator-max-microvolt = <3544000>;
 115                         regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>;
 116                         regulator-allow-set-load;
 117                         regulator-allowed-modes = <RPMH_REGULATOR_MODE_LPM
 118                                                    RPMH_REGULATOR_MODE_HPM>;
 119                 };
 120         };
 121
 122         regulators-1 {
 123                 compatible = "qcom,pmm8654au-rpmh-regulators";
 124                 qcom,pmic-id = "c";
 125
 126                 vreg_l1c: ldo1 {
 127                         regulator-name = "vreg_l1c";
 128                         regulator-min-microvolt = <1140000>;
 129                         regulator-max-microvolt = <1260000>;
 130                         regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>;
 131                         regulator-allow-set-load;
 132                         regulator-allowed-modes = <RPMH_REGULATOR_MODE_LPM
 133                                                    RPMH_REGULATOR_MODE_HPM>;
 134                 };
 135
 136                 vreg_l2c: ldo2 {
 137                         regulator-name = "vreg_l2c";
 138                         regulator-min-microvolt = <900000>;
 139                         regulator-max-microvolt = <1100000>;
 140                         regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>;
 141                         regulator-allow-set-load;
 142                         regulator-allowed-modes = <RPMH_REGULATOR_MODE_LPM
 143                                                    RPMH_REGULATOR_MODE_HPM>;
 144                 };
 145
 146                 vreg_l3c: ldo3 {
 147                         regulator-name = "vreg_l3c";
 148                         regulator-min-microvolt = <1100000>;
 149                         regulator-max-microvolt = <1300000>;
 150                         regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>;
 151                         regulator-allow-set-load;
 152                         regulator-allowed-modes = <RPMH_REGULATOR_MODE_LPM
 153                                                    RPMH_REGULATOR_MODE_HPM>;
 154                 };
 155
 156                 vreg_l4c: ldo4 {
 157                         regulator-name = "vreg_l4c";
 158                         regulator-min-microvolt = <1200000>;
 159                         regulator-max-microvolt = <1200000>;
 160                         regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>;
 161                         /*
 162                          * FIXME: This should have regulator-allow-set-load but
 163                          * we're getting an over-current fault from the PMIC
 164                          * when switching to LPM.
 165                          */
 166                 };
 167
 168                 vreg_l5c: ldo5 {
 169                         regulator-name = "vreg_l5c";
 170                         regulator-min-microvolt = <1100000>;
 171                         regulator-max-microvolt = <1300000>;
 172                         regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>;
 173                         regulator-allow-set-load;
 174                         regulator-allowed-modes = <RPMH_REGULATOR_MODE_LPM
 175                                                    RPMH_REGULATOR_MODE_HPM>;
 176                 };
 177
 178                 vreg_l6c: ldo6 {
 179                         regulator-name = "vreg_l6c";
 180                         regulator-min-microvolt = <1620000>;
 181                         regulator-max-microvolt = <1980000>;
 182                         regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>;
 183                         regulator-allow-set-load;
 184                         regulator-allowed-modes = <RPMH_REGULATOR_MODE_LPM
 185                                                    RPMH_REGULATOR_MODE_HPM>;
 186                 };
 187
 188                 vreg_l7c: ldo7 {
 189                         regulator-name = "vreg_l7c";
 190                         regulator-min-microvolt = <1620000>;
 191                         regulator-max-microvolt = <2000000>;
 192                         regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>;
 193                         regulator-allow-set-load;
 194                         regulator-allowed-modes = <RPMH_REGULATOR_MODE_LPM
 195                                                    RPMH_REGULATOR_MODE_HPM>;
 196                 };
 197
 198                 vreg_l8c: ldo8 {
 199                         regulator-name = "vreg_l8c";
 200                         regulator-min-microvolt = <2400000>;
 201                         regulator-max-microvolt = <3300000>;
 202                         regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>;
 203                         regulator-allow-set-load;
 204                         regulator-allowed-modes = <RPMH_REGULATOR_MODE_LPM
 205                                                    RPMH_REGULATOR_MODE_HPM>;
 206                 };
 207
 208                 vreg_l9c: ldo9 {
 209                         regulator-name = "vreg_l9c";
 210                         regulator-min-microvolt = <1650000>;
 211                         regulator-max-microvolt = <2700000>;
 212                         regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>;
 213                         regulator-allow-set-load;
 214                         regulator-allowed-modes = <RPMH_REGULATOR_MODE_LPM
 215                                                    RPMH_REGULATOR_MODE_HPM>;
 216                 };
 217         };
 218
 219         regulators-2 {
 220                 compatible = "qcom,pmm8654au-rpmh-regulators";
 221                 qcom,pmic-id = "e";
 222
 223                 vreg_s4e: smps4 {
 224                         regulator-name = "vreg_s4e";
 225                         regulator-min-microvolt = <970000>;
 226                         regulator-max-microvolt = <1520000>;
 227                         regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>;
 228                 };
 229
 230                 vreg_s7e: smps7 {
 231                         regulator-name = "vreg_s7e";
 232                         regulator-min-microvolt = <1010000>;
 233                         regulator-max-microvolt = <1170000>;
 234                         regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>;
 235                 };
 236
 237                 vreg_s9e: smps9 {
 238                         regulator-name = "vreg_s9e";
 239                         regulator-min-microvolt = <300000>;
 240                         regulator-max-microvolt = <570000>;
 241                         regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>;
 242                 };
 243
 244                 vreg_l6e: ldo6 {
 245                         regulator-name = "vreg_l6e";
 246                         regulator-min-microvolt = <1280000>;
 247                         regulator-max-microvolt = <1450000>;
 248                         regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>;
 249                         regulator-allow-set-load;
 250                         regulator-allowed-modes = <RPMH_REGULATOR_MODE_LPM
 251                                                    RPMH_REGULATOR_MODE_HPM>;
 252                 };
 253
 254                 vreg_l8e: ldo8 {
 255                         regulator-name = "vreg_l8e";
 256                         regulator-min-microvolt = <1800000>;
 257                         regulator-max-microvolt = <1950000>;
 258                         regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>;
 259                         regulator-allow-set-load;
 260                         regulator-allowed-modes = <RPMH_REGULATOR_MODE_LPM
 261                                                    RPMH_REGULATOR_MODE_HPM>;
 262                 };
 263         };
 264 };
 265
 266 &ethernet0 {
 267         phy-mode = "sgmii";
 268         phy-handle = <&sgmii_phy0>;
 269
 270         pinctrl-0 = <&ethernet0_default>;
 271         pinctrl-names = "default";
 272
 273         snps,mtl-rx-config = <&mtl_rx_setup>;
 274         snps,mtl-tx-config = <&mtl_tx_setup>;
 275         snps,ps-speed = <1000>;
 276
 277         status = "okay";
 278
 279         mdio {
 280                 compatible = "snps,dwmac-mdio";
 281                 #address-cells = <1>;
 282                 #size-cells = <0>;
 283
 284                 sgmii_phy0: phy@8 {
 285                         compatible = "ethernet-phy-id0141.0dd4";
 286                         reg = <0x8>;
 287                         device_type = "ethernet-phy";
 288                         reset-gpios = <&pmm8654au_2_gpios 8 GPIO_ACTIVE_LOW>;
 289                         reset-assert-us = <11000>;
 290                         reset-deassert-us = <70000>;
 291                 };
 292
 293                 sgmii_phy1: phy@a {
 294                         compatible = "ethernet-phy-id0141.0dd4";
 295                         reg = <0xa>;
 296                         device_type = "ethernet-phy";
 297                         reset-gpios = <&pmm8654au_2_gpios 9 GPIO_ACTIVE_LOW>;
 298                         reset-assert-us = <11000>;
 299                         reset-deassert-us = <70000>;
 300                 };
 301         };
 302
 303         mtl_rx_setup: rx-queues-config {
 304                 snps,rx-queues-to-use = <4>;
 305                 snps,rx-sched-sp;
 306
 307                 queue0 {
 308                         snps,dcb-algorithm;
 309                         snps,map-to-dma-channel = <0x0>;
 310                         snps,route-up;
 311                         snps,priority = <0x1>;
 312                 };
 313
 314                 queue1 {
 315                         snps,dcb-algorithm;
 316                         snps,map-to-dma-channel = <0x1>;
 317                         snps,route-ptp;
 318                 };
 319
 320                 queue2 {
 321                         snps,avb-algorithm;
 322                         snps,map-to-dma-channel = <0x2>;
 323                         snps,route-avcp;
 324                 };
 325
 326                 queue3 {
 327                         snps,avb-algorithm;
 328                         snps,map-to-dma-channel = <0x3>;
 329                         snps,priority = <0xc>;
 330                 };
 331         };
 332
 333         mtl_tx_setup: tx-queues-config {
 334                 snps,tx-queues-to-use = <4>;
 335                 snps,tx-sched-sp;
 336
 337                 queue0 {
 338                         snps,dcb-algorithm;
 339                 };
 340
 341                 queue1 {
 342                         snps,dcb-algorithm;
 343                 };
 344
 345                 queue2 {
 346                         snps,avb-algorithm;
 347                         snps,send_slope = <0x1000>;
 348                         snps,idle_slope = <0x1000>;
 349                         snps,high_credit = <0x3e800>;
 350                         snps,low_credit = <0xffc18000>;
 351                 };
 352
 353                 queue3 {
 354                         snps,avb-algorithm;
 355                         snps,send_slope = <0x1000>;
 356                         snps,idle_slope = <0x1000>;
 357                         snps,high_credit = <0x3e800>;
 358                         snps,low_credit = <0xffc18000>;
 359                 };
 360         };
 361 };
 362
 363 &ethernet1 {
 364         phy-mode = "sgmii";
 365         phy-handle = <&sgmii_phy1>;
 366
 367         snps,mtl-rx-config = <&mtl_rx_setup1>;
 368         snps,mtl-tx-config = <&mtl_tx_setup1>;
 369         snps,ps-speed = <1000>;
 370
 371         status = "okay";
 372
 373         mtl_rx_setup1: rx-queues-config {
 374                 snps,rx-queues-to-use = <4>;
 375                 snps,rx-sched-sp;
 376
 377                 queue0 {
 378                         snps,dcb-algorithm;
 379                         snps,map-to-dma-channel = <0x0>;
 380                         snps,route-up;
 381                         snps,priority = <0x1>;
 382                 };
 383
 384                 queue1 {
 385                         snps,dcb-algorithm;
 386                         snps,map-to-dma-channel = <0x1>;
 387                         snps,route-ptp;
 388                 };
 389
 390                 queue2 {
 391                         snps,avb-algorithm;
 392                         snps,map-to-dma-channel = <0x2>;
 393                         snps,route-avcp;
 394                 };
 395
 396                 queue3 {
 397                         snps,avb-algorithm;
 398                         snps,map-to-dma-channel = <0x3>;
 399                         snps,priority = <0xc>;
 400                 };
 401         };
 402
 403         mtl_tx_setup1: tx-queues-config {
 404                 snps,tx-queues-to-use = <4>;
 405                 snps,tx-sched-sp;
 406
 407                 queue0 {
 408                         snps,dcb-algorithm;
 409                 };
 410
 411                 queue1 {
 412                         snps,dcb-algorithm;
 413                 };
 414
 415                 queue2 {
 416                         snps,avb-algorithm;
 417                         snps,send_slope = <0x1000>;
 418                         snps,idle_slope = <0x1000>;
 419                         snps,high_credit = <0x3e800>;
 420                         snps,low_credit = <0xffc18000>;
 421                 };
 422
 423                 queue3 {
 424                         snps,avb-algorithm;
 425                         snps,send_slope = <0x1000>;
 426                         snps,idle_slope = <0x1000>;
 427                         snps,high_credit = <0x3e800>;
 428                         snps,low_credit = <0xffc18000>;
 429                 };
 430         };
 431 };
 432
 433 &i2c11 {
 434         clock-frequency = <400000>;
 435         pinctrl-0 = <&qup_i2c11_default>;
 436         pinctrl-names = "default";
 437         status = "okay";
 438 };
 439
 440 &i2c18 {
 441         clock-frequency = <400000>;
 442         pinctrl-0 = <&qup_i2c18_default>;
 443         pinctrl-names = "default";
 444         status = "okay";
 445 };
 446
 447 &pmm8654au_0_gpios {
 448         gpio-line-names = "DS_EN",
 449                           "POFF_COMPLETE",
 450                           "UFS0_VER_ID",
 451                           "FAST_POFF",
 452                           "DBU1_PON_DONE",
 453                           "AOSS_SLEEP",
 454                           "CAM_DES0_EN",
 455                           "CAM_DES1_EN",
 456                           "CAM_DES2_EN",
 457                           "CAM_DES3_EN",
 458                           "UEFI",
 459                           "ANALOG_PON_OPT";
 460 };
 461
 462 &pmm8654au_1_gpios {
 463         gpio-line-names = "PMIC_C_ID0",
 464                           "PMIC_C_ID1",
 465                           "UFS1_VER_ID",
 466                           "IPA_PWR",
 467                           "",
 468                           "WLAN_DBU4_EN",
 469                           "WLAN_EN",
 470                           "BT_EN",
 471                           "USB2_PWR_EN",
 472                           "USB2_FAULT";
 473
 474         usb2_en_state: usb2-en-state {
 475                 pins = "gpio9";
 476                 function = "normal";
 477                 output-high;
 478                 power-source = <0>;
 479         };
 480 };
 481
 482 &pmm8654au_2_gpios {
 483         gpio-line-names = "PMIC_E_ID0",
 484                           "PMIC_E_ID1",
 485                           "USB0_PWR_EN",
 486                           "USB0_FAULT",
 487                           "SENSOR_IRQ_1",
 488                           "SENSOR_IRQ_2",
 489                           "SENSOR_RST",
 490                           "SGMIIO0_RST",
 491                           "SGMIIO1_RST",
 492                           "USB1_PWR_ENABLE",
 493                           "USB1_FAULT",
 494                           "VMON_SPX8";
 495
 496         usb0_en_state: usb0-en-state {
 497                 pins = "gpio3";
 498                 function = "normal";
 499                 output-high;
 500                 power-source = <0>;
 501         };
 502
 503         usb1_en_state: usb1-en-state {
 504                 pins = "gpio10";
 505                 function = "normal";
 506                 output-high;
 507                 power-source = <0>;
 508         };
 509 };
 510
 511 &pmm8654au_3_gpios {
 512         gpio-line-names = "PMIC_G_ID0",
 513                           "PMIC_G_ID1",
 514                           "GNSS_RST",
 515                           "GNSS_EN",
 516                           "GNSS_BOOT_MODE";
 517 };
 518
 519 &qupv3_id_1 {
 520         status = "okay";
 521 };
 522
 523 &qupv3_id_2 {
 524         status = "okay";
 525 };
 526
 527 &serdes0 {
 528         phy-supply = <&vreg_l5a>;
 529         status = "okay";
 530 };
 531
 532 &serdes1 {
 533         phy-supply = <&vreg_l5a>;
 534         status = "okay";
 535 };
 536
 537 &sleep_clk {
 538         clock-frequency = <32764>;
 539 };
 540
 541 &spi16 {
 542         pinctrl-0 = <&qup_spi16_default>;
 543         pinctrl-names = "default";
 544         status = "okay";
 545 };
 546
 547 &tlmm {
 548         ethernet0_default: ethernet0-default-state {
 549                 ethernet0_mdc: ethernet0-mdc-pins {
 550                         pins = "gpio8";
 551                         function = "emac0_mdc";
 552                         drive-strength = <16>;
 553                         bias-pull-up;
 554                 };
 555
 556                 ethernet0_mdio: ethernet0-mdio-pins {
 557                         pins = "gpio9";
 558                         function = "emac0_mdio";
 559                         drive-strength = <16>;
 560                         bias-pull-up;
 561                 };
 562         };
 563
 564         qup_uart10_default: qup-uart10-state {
 565                 pins = "gpio46", "gpio47";
 566                 function = "qup1_se3";
 567         };
 568
 569         qup_spi16_default: qup-spi16-state {
 570                 pins = "gpio86", "gpio87", "gpio88", "gpio89";
 571                 function = "qup2_se2";
 572                 drive-strength = <6>;
 573                 bias-disable;
 574         };
 575
 576         qup_i2c11_default: qup-i2c11-state {
 577                 pins = "gpio48", "gpio49";
 578                 function = "qup1_se4";
 579                 drive-strength = <2>;
 580                 bias-pull-up;
 581         };
 582
 583         qup_i2c18_default: qup-i2c18-state {
 584                 pins = "gpio95", "gpio96";
 585                 function = "qup2_se4";
 586                 drive-strength = <2>;
 587                 bias-pull-up;
 588         };
 589
 590         qup_uart12_default: qup-uart12-state {
 591                 qup_uart12_cts: qup-uart12-cts-pins {
 592                         pins = "gpio52";
 593                         function = "qup1_se5";
 594                         bias-disable;
 595                 };
 596
 597                 qup_uart12_rts: qup-uart12-rts-pins {
 598                         pins = "gpio53";
 599                         function = "qup1_se5";
 600                         bias-pull-down;
 601                 };
 602
 603                 qup_uart12_tx: qup-uart12-tx-pins {
 604                         pins = "gpio54";
 605                         function = "qup1_se5";
 606                         bias-pull-up;
 607                 };
 608
 609                 qup_uart12_rx: qup-uart12-rx-pins {
 610                         pins = "gpio55";
 611                         function = "qup1_se5";
 612                         bias-pull-down;
 613                 };
 614         };
 615
 616         qup_uart17_default: qup-uart17-state {
 617                 qup_uart17_cts: qup-uart17-cts-pins {
 618                         pins = "gpio91";
 619                         function = "qup2_se3";
 620                         bias-disable;
 621                 };
 622
 623                 qup_uart17_rts: qup0-uart17-rts-pins {
 624                         pins = "gpio92";
 625                         function = "qup2_se3";
 626                         bias-pull-down;
 627                 };
 628
 629                 qup_uart17_tx: qup0-uart17-tx-pins {
 630                         pins = "gpio93";
 631                         function = "qup2_se3";
 632                         bias-pull-up;
 633                 };
 634
 635                 qup_uart17_rx: qup0-uart17-rx-pins {
 636                         pins = "gpio94";
 637                         function = "qup2_se3";
 638                         bias-pull-down;
 639                 };
 640         };
 641
 642         pcie0_default_state: pcie0-default-state {
 643                 perst-pins {
 644                         pins = "gpio2";
 645                         function = "gpio";
 646                         drive-strength = <2>;
 647                         bias-pull-down;
 648                 };
 649
 650                 clkreq-pins {
 651                         pins = "gpio1";
 652                         function = "pcie0_clkreq";
 653                         drive-strength = <2>;
 654                         bias-pull-up;
 655                 };
 656
 657                 wake-pins {
 658                         pins = "gpio0";
 659                         function = "gpio";
 660                         drive-strength = <2>;
 661                         bias-pull-up;
 662                 };
 663         };
 664
 665         pcie1_default_state: pcie1-default-state {
 666                 perst-pins {
 667                         pins = "gpio4";
 668                         function = "gpio";
 669                         drive-strength = <2>;
 670                         bias-pull-down;
 671                 };
 672
 673                 clkreq-pins {
 674                         pins = "gpio3";
 675                         function = "pcie1_clkreq";
 676                         drive-strength = <2>;
 677                         bias-pull-up;
 678                 };
 679
 680                 wake-pins {
 681                         pins = "gpio5";
 682                         function = "gpio";
 683                         drive-strength = <2>;
 684                         bias-pull-up;
 685                 };
 686         };
 687 };
 688
 689 &pcie0 {
 690         perst-gpios = <&tlmm 2 GPIO_ACTIVE_LOW>;
 691         wake-gpios = <&tlmm 0 GPIO_ACTIVE_HIGH>;
 692
 693         pinctrl-names = "default";
 694         pinctrl-0 = <&pcie0_default_state>;
 695
 696         status = "okay";
 697 };
 698
 699 &pcie1 {
 700         perst-gpios = <&tlmm 4 GPIO_ACTIVE_LOW>;
 701         wake-gpios = <&tlmm 5 GPIO_ACTIVE_HIGH>;
 702
 703         pinctrl-names = "default";
 704         pinctrl-0 = <&pcie1_default_state>;
 705
 706         status = "okay";
 707 };
 708
 709 &pcie0_phy {
 710         vdda-phy-supply = <&vreg_l5a>;
 711         vdda-pll-supply = <&vreg_l1c>;
 712
 713         status = "okay";
 714 };
 715
 716 &pcie1_phy {
 717         vdda-phy-supply = <&vreg_l5a>;
 718         vdda-pll-supply = <&vreg_l1c>;
 719
 720         status = "okay";
 721 };
 722
 723 &uart10 {
 724         compatible = "qcom,geni-debug-uart";
 725         pinctrl-0 = <&qup_uart10_default>;
 726         pinctrl-names = "default";
 727         status = "okay";
 728 };
 729
 730 &uart12 {
 731         pinctrl-0 = <&qup_uart12_default>;
 732         pinctrl-names = "default";
 733         status = "okay";
 734 };
 735
 736 &uart17 {
 737         pinctrl-0 = <&qup_uart17_default>;
 738         pinctrl-names = "default";
 739         status = "okay";
 740 };
 741
 742 &ufs_mem_hc {
 743         reset-gpios = <&tlmm 149 GPIO_ACTIVE_LOW>;
 744         vcc-supply = <&vreg_l8a>;
 745         vcc-max-microamp = <1100000>;
 746         vccq-supply = <&vreg_l4c>;
 747         vccq-max-microamp = <1200000>;
 748
 749         status = "okay";
 750 };
 751
 752 &ufs_mem_phy {
 753         vdda-phy-supply = <&vreg_l4a>;
 754         vdda-pll-supply = <&vreg_l1c>;
 755
 756         status = "okay";
 757 };
 758
 759 &usb_0 {
 760         pinctrl-names = "default";
 761         pinctrl-0 = <&usb0_en_state>;
 762
 763         status = "okay";
 764 };
 765
 766 &usb_0_dwc3 {
 767         dr_mode = "peripheral";
 768 };
 769
 770 &usb_0_hsphy {
 771         vdda-pll-supply = <&vreg_l7a>;
 772         vdda18-supply = <&vreg_l6c>;
 773         vdda33-supply = <&vreg_l9a>;
 774
 775         status = "okay";
 776 };
 777
 778 &usb_0_qmpphy {
 779         vdda-phy-supply = <&vreg_l1c>;
 780         vdda-pll-supply = <&vreg_l7a>;
 781
 782         status = "okay";
 783 };
 784
 785 &usb_1 {
 786         pinctrl-names = "default";
 787         pinctrl-0 = <&usb1_en_state>;
 788
 789         status = "okay";
 790 };
 791
 792 &usb_1_dwc3 {
 793         dr_mode = "host";
 794 };
 795
 796 &usb_1_hsphy {
 797         vdda-pll-supply = <&vreg_l7a>;
 798         vdda18-supply = <&vreg_l6c>;
 799         vdda33-supply = <&vreg_l9a>;
 800
 801         status = "okay";
 802 };
 803
 804 &usb_1_qmpphy {
 805         vdda-phy-supply = <&vreg_l1c>;
 806         vdda-pll-supply = <&vreg_l7a>;
 807
 808         status = "okay";
 809 };
 810
 811 &usb_2 {
 812         pinctrl-names = "default";
 813         pinctrl-0 = <&usb2_en_state>;
 814
 815         status = "okay";
 816 };
 817
 818 &usb_2_dwc3 {
 819         dr_mode = "host";
 820 };
 821
 822 &usb_2_hsphy {
 823         vdda-pll-supply = <&vreg_l7a>;
 824         vdda18-supply = <&vreg_l6c>;
 825         vdda33-supply = <&vreg_l9a>;
 826
 827         status = "okay";
 828 };
 829
 830 &xo_board_clk {
 831         clock-frequency = <38400000>;
 832 };