arch/arm64/boot/dts/qcom/msm8998-oneplus-common.dtsi

   1 // SPDX-License-Identifier: BSD-3-Clause
   2 /*
   3  * OnePlus 5(T) (cheeseburger / dumpling) common device tree source based on msm8998-mtp.dtsi
   4  *
   5  * Copyright (c) 2021, Jami Kettunen <jamipkettunen@gmail.com>
   6  * Copyright (c) 2016, The Linux Foundation. All rights reserved.
   7  */
   8
   9 /dts-v1/;
  10
  11 #include <dt-bindings/gpio/gpio.h>
  12 #include <dt-bindings/pinctrl/qcom,pmic-gpio.h>
  13 #include "msm8998.dtsi"
  14 #include "pm8998.dtsi"
  15 #include "pmi8998.dtsi"
  16 #include "pm8005.dtsi"
  17
  18 / {
  19         /* Required for bootloader to select correct board */
  20         qcom,msm-id = <292 0x20001>; /* 8998 v2.1 */
  21
  22         chosen {
  23                 #address-cells = <2>;
  24                 #size-cells = <2>;
  25                 ranges;
  26
  27                 /* Use display framebuffer setup by the UEFI XBL bootloader for simplefb */
  28                 framebuffer0: framebuffer@9d400000 {
  29                         compatible = "simple-framebuffer";
  30                         reg = <0x0 0x9d400000 0x0 0x2400000>;
  31                         width = <1080>;
  32                         height = <1920>;
  33                         stride = <(1080 * 4)>;
  34                         format = "a8r8g8b8";
  35                 };
  36         };
  37
  38         reserved-memory {
  39                 /* Bootloader display framebuffer region */
  40                 cont_splash_mem: memory@9d400000 {
  41                         reg = <0x0 0x9d400000 0x0 0x2400000>;
  42                         no-map;
  43                 };
  44
  45                 /* For getting crash logs using Android downstream kernels */
  46                 ramoops@ac000000 {
  47                         compatible = "ramoops";
  48                         reg = <0x0 0xac000000 0x0 0x200000>;
  49                         console-size = <0x80000>;
  50                         pmsg-size = <0x40000>;
  51                         record-size = <0x8000>;
  52                         ftrace-size = <0x20000>;
  53                 };
  54
  55                 /*
  56                  * The following memory regions on downstream are "dynamically allocated"
  57                  * but given the same addresses every time. Hard code them as these addresses
  58                  * are where the OnePlus signed firmware expects them to be.
  59                  */
  60                 ipa_fws_region: ipa@f6800000 {
  61                         compatible = "shared-dma-pool";
  62                         reg = <0x0 0xf6800000 0x0 0x5000>;
  63                         no-map;
  64                 };
  65                 zap_shader_region: gpu@f6900000 {
  66                         compatible = "shared-dma-pool";
  67                         reg = <0x0 0xf6900000 0x0 0x2000>;
  68                         no-map;
  69                 };
  70         };
  71
  72         gpio-keys {
  73                 compatible = "gpio-keys";
  74                 label = "Volume buttons";
  75                 autorepeat;
  76
  77                 pinctrl-names = "default";
  78                 pinctrl-0 = <&vol_keys_default>;
  79
  80                 vol-down {
  81                         label = "Volume down";
  82                         gpios = <&pm8998_gpio 5 GPIO_ACTIVE_LOW>;
  83                         linux,code = <KEY_VOLUMEDOWN>;
  84                         debounce-interval = <15>;
  85                         wakeup-source;
  86                 };
  87
  88                 vol-up {
  89                         label = "Volume up";
  90                         gpios = <&pm8998_gpio 6 GPIO_ACTIVE_LOW>;
  91                         linux,code = <KEY_VOLUMEUP>;
  92                         debounce-interval = <15>;
  93                         wakeup-source;
  94                 };
  95         };
  96
  97         gpio-hall-sensor {
  98                 compatible = "gpio-keys";
  99                 label = "Hall effect sensor";
 100
 101                 pinctrl-names = "default";
 102                 pinctrl-0 = <&hall_sensor_default>;
 103
 104                 hall-sensor {
 105                         label = "Hall Effect Sensor";
 106                         gpios = <&tlmm 124 GPIO_ACTIVE_LOW>;
 107                         linux,input-type = <EV_SW>;
 108                         linux,code = <SW_LID>;
 109                         linux,can-disable;
 110                         wakeup-source;
 111                 };
 112         };
 113
 114         vph_pwr: vph-pwr-regulator {
 115                 compatible = "regulator-fixed";
 116                 regulator-name = "vph_pwr";
 117                 regulator-always-on;
 118                 regulator-boot-on;
 119         };
 120 };
 121
 122 /*
 123  * OnePlus' ADSP firmware requires 30 MiB in total, so increase the adsp_mem
 124  * region by 4 MiB to account for this while relocating the other now
 125  * conflicting memory nodes accordingly.
 126  */
 127 &adsp_mem {
 128         reg = <0x0 0x8b200000 0x0 0x1e00000>;
 129 };
 130 &mpss_mem {
 131         reg = <0x0 0x8d000000 0x0 0x7000000>;
 132 };
 133 &venus_mem {
 134         reg = <0x0 0x94000000 0x0 0x500000>;
 135 };
 136 &mba_mem {
 137         reg = <0x0 0x94500000 0x0 0x200000>;
 138 };
 139 &slpi_mem {
 140         reg = <0x0 0x94700000 0x0 0xf00000>;
 141 };
 142 &ipa_fw_mem {
 143         reg = <0x0 0x95600000 0x0 0x10000>;
 144 };
 145 &ipa_gsi_mem {
 146         reg = <0x0 0x95610000 0x0 0x5000>;
 147 };
 148 &gpu_mem {
 149         reg = <0x0 0x95615000 0x0 0x100000>;
 150 };
 151 &wlan_msa_mem {
 152         reg = <0x0 0x95715000 0x0 0x100000>;
 153 };
 154
 155 &blsp1_i2c5 {
 156         status = "okay";
 157
 158         touchscreen@20 {
 159                 compatible = "syna,rmi4-i2c";
 160                 reg = <0x20>;
 161                 #address-cells = <1>;
 162                 #size-cells = <0>;
 163
 164                 interrupt-parent = <&tlmm>;
 165                 interrupts = <125 IRQ_TYPE_EDGE_FALLING>;
 166
 167                 pinctrl-names = "default";
 168                 pinctrl-0 = <&ts_int_active &ts_reset_active>;
 169
 170                 vdd-supply = <&vreg_l28_3p0>;
 171                 vio-supply = <&vreg_l6a_1p8>;
 172
 173                 syna,reset-delay-ms = <20>;
 174                 syna,startup-delay-ms = <20>;
 175
 176                 rmi4-f01@1 {
 177                         reg = <0x01>;
 178                         syna,nosleep-mode = <1>;
 179                 };
 180
 181                 rmi4_f12: rmi4-f12@12 {
 182                         reg = <0x12>;
 183                         syna,rezero-wait-ms = <20>;
 184                         syna,sensor-type = <1>;
 185                         touchscreen-x-mm = <68>;
 186                         touchscreen-y-mm = <122>;
 187                 };
 188         };
 189 };
 190
 191 &blsp1_i2c6 {
 192         status = "okay";
 193
 194         nfc@28 {
 195                 compatible = "nxp,nxp-nci-i2c";
 196                 reg = <0x28>;
 197
 198                 interrupt-parent = <&tlmm>;
 199                 interrupts = <92 IRQ_TYPE_LEVEL_HIGH>;
 200
 201                 enable-gpios = <&tlmm 116 GPIO_ACTIVE_HIGH>;
 202
 203                 pinctrl-names = "default";
 204                 pinctrl-0 = <&nfc_int_active &nfc_enable_active>;
 205         };
 206 };
 207
 208 &blsp1_uart3 {
 209         status = "okay";
 210
 211         bluetooth {
 212                 compatible = "qcom,wcn3990-bt";
 213
 214                 vddio-supply = <&vreg_s4a_1p8>;
 215                 vddxo-supply = <&vreg_l7a_1p8>;
 216                 vddrf-supply = <&vreg_l17a_1p3>;
 217                 vddch0-supply = <&vreg_l25a_3p3>;
 218                 max-speed = <3200000>;
 219         };
 220 };
 221
 222 &blsp1_uart3_on {
 223         rx {
 224                 /delete-property/ bias-disable;
 225                 /*
 226                  * Configure a pull-up on 46 (RX). This is needed to
 227                  * avoid garbage data when the TX pin of the Bluetooth
 228                  * module is in tri-state (module powered off or not
 229                  * driving the signal yet).
 230                  */
 231                 bias-pull-up;
 232         };
 233
 234         cts {
 235                 /delete-property/ bias-disable;
 236                 /*
 237                  * Configure a pull-down on 47 (CTS) to match the pull
 238                  * of the Bluetooth module.
 239                  */
 240                 bias-pull-down;
 241         };
 242 };
 243
 244 &blsp2_uart1 {
 245         status = "okay";
 246 };
 247
 248 &pm8005_lsid1 {
 249         pm8005-regulators {
 250                 compatible = "qcom,pm8005-regulators";
 251
 252                 vdd_s1-supply = <&vph_pwr>;
 253
 254                 pm8005_s1: s1 { /* VDD_GFX supply */
 255                         regulator-min-microvolt = <524000>;
 256                         regulator-max-microvolt = <1100000>;
 257                         regulator-enable-ramp-delay = <500>;
 258
 259                         /* hack until we rig up the gpu consumer */
 260                         regulator-always-on;
 261                 };
 262         };
 263 };
 264
 265 &pm8998_gpio {
 266         vol_keys_default: vol-keys-default {
 267                 pinconf {
 268                         pins = "gpio5", "gpio6";
 269                         function = "normal";
 270                         bias-pull-up;
 271                         input-enable;
 272                         qcom,drive-strength = <PMIC_GPIO_STRENGTH_NO>;
 273                 };
 274         };
 275 };
 276
 277 &qusb2phy {
 278         status = "okay";
 279
 280         vdd-supply = <&vreg_l1a_0p875>;
 281         vdda-pll-supply = <&vreg_l12a_1p8>;
 282         vdda-phy-dpdm-supply = <&vreg_l24a_3p075>;
 283 };
 284
 285 &rpm_requests {
 286         pm8998-regulators {
 287                 compatible = "qcom,rpm-pm8998-regulators";
 288
 289                 vdd_s1-supply = <&vph_pwr>;
 290                 vdd_s2-supply = <&vph_pwr>;
 291                 vdd_s3-supply = <&vph_pwr>;
 292                 vdd_s4-supply = <&vph_pwr>;
 293                 vdd_s5-supply = <&vph_pwr>;
 294                 vdd_s6-supply = <&vph_pwr>;
 295                 vdd_s7-supply = <&vph_pwr>;
 296                 vdd_s8-supply = <&vph_pwr>;
 297                 vdd_s9-supply = <&vph_pwr>;
 298                 vdd_s10-supply = <&vph_pwr>;
 299                 vdd_s11-supply = <&vph_pwr>;
 300                 vdd_s12-supply = <&vph_pwr>;
 301                 vdd_s13-supply = <&vph_pwr>;
 302                 vdd_l1_l27-supply = <&vreg_s7a_1p025>;
 303                 vdd_l2_l8_l17-supply = <&vreg_s3a_1p35>;
 304                 vdd_l3_l11-supply = <&vreg_s7a_1p025>;
 305                 vdd_l4_l5-supply = <&vreg_s7a_1p025>;
 306                 vdd_l6-supply = <&vreg_s5a_2p04>;
 307                 vdd_l7_l12_l14_l15-supply = <&vreg_s5a_2p04>;
 308                 vdd_l9-supply = <&vreg_bob>;
 309                 vdd_l10_l23_l25-supply = <&vreg_bob>;
 310                 vdd_l13_l19_l21-supply = <&vreg_bob>;
 311                 vdd_l16_l28-supply = <&vreg_bob>;
 312                 vdd_l18_l22-supply = <&vreg_bob>;
 313                 vdd_l20_l24-supply = <&vreg_bob>;
 314                 vdd_l26-supply = <&vreg_s3a_1p35>;
 315                 vdd_lvs1_lvs2-supply = <&vreg_s4a_1p8>;
 316
 317                 vreg_s3a_1p35: s3 {
 318                         regulator-min-microvolt = <1352000>;
 319                         regulator-max-microvolt = <1352000>;
 320                 };
 321                 vreg_s4a_1p8: s4 {
 322                         regulator-min-microvolt = <1800000>;
 323                         regulator-max-microvolt = <1800000>;
 324                         regulator-allow-set-load;
 325                 };
 326                 vreg_s5a_2p04: s5 {
 327                         regulator-min-microvolt = <1904000>;
 328                         regulator-max-microvolt = <2040000>;
 329                 };
 330                 vreg_s7a_1p025: s7 {
 331                         regulator-min-microvolt = <900000>;
 332                         regulator-max-microvolt = <1028000>;
 333                 };
 334                 vreg_l1a_0p875: l1 {
 335                         regulator-min-microvolt = <880000>;
 336                         regulator-max-microvolt = <880000>;
 337                 };
 338                 vreg_l2a_1p2: l2 {
 339                         regulator-min-microvolt = <1200000>;
 340                         regulator-max-microvolt = <1200000>;
 341                 };
 342                 vreg_l3a_1p0: l3 {
 343                         regulator-min-microvolt = <1000000>;
 344                         regulator-max-microvolt = <1000000>;
 345                 };
 346                 vreg_l5a_0p8: l5 {
 347                         regulator-min-microvolt = <800000>;
 348                         regulator-max-microvolt = <800000>;
 349                 };
 350                 vreg_l6a_1p8: l6 {
 351                         regulator-min-microvolt = <1808000>;
 352                         regulator-max-microvolt = <1808000>;
 353                 };
 354                 vreg_l7a_1p8: l7 {
 355                         regulator-min-microvolt = <1800000>;
 356                         regulator-max-microvolt = <1800000>;
 357                 };
 358                 vreg_l8a_1p2: l8 {
 359                         regulator-min-microvolt = <1200000>;
 360                         regulator-max-microvolt = <1200000>;
 361                 };
 362                 vreg_l9a_1p8: l9 {
 363                         regulator-min-microvolt = <1808000>;
 364                         regulator-max-microvolt = <2960000>;
 365                 };
 366                 vreg_l10a_1p8: l10 {
 367                         regulator-min-microvolt = <1808000>;
 368                         regulator-max-microvolt = <2960000>;
 369                 };
 370                 vreg_l11a_1p0: l11 {
 371                         regulator-min-microvolt = <1000000>;
 372                         regulator-max-microvolt = <1000000>;
 373                 };
 374                 vreg_l12a_1p8: l12 {
 375                         regulator-min-microvolt = <1800000>;
 376                         regulator-max-microvolt = <1800000>;
 377                 };
 378                 vreg_l13a_2p95: l13 {
 379                         regulator-min-microvolt = <1808000>;
 380                         regulator-max-microvolt = <2960000>;
 381                 };
 382                 vreg_l14a_1p88: l14 {
 383                         regulator-min-microvolt = <1880000>;
 384                         regulator-max-microvolt = <1880000>;
 385                 };
 386                 vreg_l15a_1p8: l15 {
 387                         regulator-min-microvolt = <1800000>;
 388                         regulator-max-microvolt = <1800000>;
 389                 };
 390                 vreg_l16a_2p7: l16 {
 391                         regulator-min-microvolt = <2704000>;
 392                         regulator-max-microvolt = <2704000>;
 393                 };
 394                 vreg_l17a_1p3: l17 {
 395                         regulator-min-microvolt = <1304000>;
 396                         regulator-max-microvolt = <1304000>;
 397                 };
 398                 vreg_l18a_2p7: l18 {
 399                         regulator-min-microvolt = <2704000>;
 400                         regulator-max-microvolt = <2704000>;
 401                 };
 402                 vreg_l19a_3p0: l19 {
 403                         regulator-min-microvolt = <3008000>;
 404                         regulator-max-microvolt = <3008000>;
 405                 };
 406                 vreg_l20a_2p95: l20 {
 407                         regulator-min-microvolt = <2960000>;
 408                         regulator-max-microvolt = <2960000>;
 409                         regulator-allow-set-load;
 410                 };
 411                 vreg_l21a_2p95: l21 {
 412                         regulator-min-microvolt = <2960000>;
 413                         regulator-max-microvolt = <2960000>;
 414                         regulator-allow-set-load;
 415                         regulator-system-load = <800000>;
 416                 };
 417                 vreg_l22a_2p85: l22 {
 418                         regulator-min-microvolt = <2864000>;
 419                         regulator-max-microvolt = <2864000>;
 420                 };
 421                 vreg_l23a_3p3: l23 {
 422                         regulator-min-microvolt = <3312000>;
 423                         regulator-max-microvolt = <3312000>;
 424                 };
 425                 vreg_l24a_3p075: l24 {
 426                         regulator-min-microvolt = <3088000>;
 427                         regulator-max-microvolt = <3088000>;
 428                 };
 429                 vreg_l25a_3p3: l25 {
 430                         regulator-min-microvolt = <3104000>;
 431                         regulator-max-microvolt = <3312000>;
 432                 };
 433                 vreg_l26a_1p2: l26 {
 434                         regulator-min-microvolt = <1200000>;
 435                         regulator-max-microvolt = <1200000>;
 436                         regulator-allow-set-load;
 437                 };
 438                 vreg_l28_3p0: l28 {
 439                         regulator-min-microvolt = <3008000>;
 440                         regulator-max-microvolt = <3008000>;
 441                 };
 442                 vreg_lvs1a_1p8: lvs1 { };
 443                 vreg_lvs2a_1p8: lvs2 { };
 444         };
 445
 446         pmi8998-regulators {
 447                 compatible = "qcom,rpm-pmi8998-regulators";
 448
 449                 vdd_bob-supply = <&vph_pwr>;
 450
 451                 vreg_bob: bob {
 452                         regulator-min-microvolt = <3312000>;
 453                         regulator-max-microvolt = <3600000>;
 454                 };
 455         };
 456 };
 457
 458 &tlmm {
 459         gpio-reserved-ranges = <0 4>, <81 4>;
 460
 461         hall_sensor_default: hall-sensor-default {
 462                 pins = "gpio124";
 463                 function = "gpio";
 464                 drive-strength = <2>;
 465                 bias-disable;
 466                 input-enable;
 467         };
 468
 469         ts_int_active: ts-int-active {
 470                 pins = "gpio125";
 471                 function = "gpio";
 472                 drive-strength = <8>;
 473                 bias-pull-up;
 474         };
 475
 476         ts_reset_active: ts-reset-active {
 477                 pins = "gpio89";
 478                 function = "gpio";
 479                 drive-strength = <8>;
 480                 bias-pull-up;
 481         };
 482
 483         nfc_int_active: nfc-int-active {
 484                 pins = "gpio92";
 485                 function = "gpio";
 486                 drive-strength = <6>;
 487                 bias-pull-up;
 488         };
 489
 490         nfc_enable_active: nfc-enable-active {
 491                 pins = "gpio12", "gpio116";
 492                 function = "gpio";
 493                 drive-strength = <6>;
 494                 bias-pull-up;
 495         };
 496 };
 497
 498 &ufshc {
 499         status = "okay";
 500
 501         vcc-supply = <&vreg_l20a_2p95>;
 502         vccq-supply = <&vreg_l26a_1p2>;
 503         vccq2-supply = <&vreg_s4a_1p8>;
 504         vcc-max-microamp = <750000>;
 505         vccq-max-microamp = <560000>;
 506         vccq2-max-microamp = <750000>;
 507 };
 508
 509 &ufsphy {
 510         status = "okay";
 511
 512         vdda-phy-supply = <&vreg_l1a_0p875>;
 513         vdda-pll-supply = <&vreg_l2a_1p2>;
 514         vddp-ref-clk-supply = <&vreg_l26a_1p2>;
 515 };
 516
 517 &usb3 {
 518         status = "okay";
 519
 520         /* Disable USB3 clock requirement as the device only supports USB2 */
 521         qcom,select-utmi-as-pipe-clk;
 522 };
 523
 524 &usb3_dwc3 {
 525         /* Drop the unused USB 3 PHY */
 526         phys = <&qusb2phy>;
 527         phy-names = "usb2-phy";
 528
 529         /* Fastest mode for USB 2 */
 530         maximum-speed = "high-speed";
 531
 532         /* Force to peripheral until we can switch modes */
 533         dr_mode = "peripheral";
 534 };
 535
 536 &wifi {
 537         /* Leave disabled until MSS is functional */
 538         vdd-0.8-cx-mx-supply = <&vreg_l5a_0p8>;
 539         vdd-1.8-xo-supply = <&vreg_l7a_1p8>;
 540         vdd-1.3-rfa-supply = <&vreg_l17a_1p3>;
 541         vdd-3.3-ch0-supply = <&vreg_l25a_3p3>;
 542 };