arch/arm64/boot/dts/freescale/imx8mm-mx8menlo.dts

   1 // SPDX-License-Identifier: GPL-2.0+ OR MIT
   2 /*
   3  * Copyright 2021-2022 Marek Vasut <marex@denx.de>
   4  */
   5
   6 /dts-v1/;
   7
   8 #include "imx8mm-verdin.dtsi"
   9
  10 / {
  11         model = "MENLO MX8MM EMBEDDED DEVICE";
  12         compatible = "menlo,mx8menlo",
  13                      "toradex,verdin-imx8mm",
  14                      "fsl,imx8mm";
  15
  16         /delete-node/ gpio-keys;
  17
  18         leds {
  19                 compatible = "gpio-leds";
  20                 pinctrl-names = "default";
  21                 pinctrl-0 = <&pinctrl_led>;
  22
  23                 led-1 {
  24                         label = "TestLed601";
  25                         gpios = <&gpio4 18 GPIO_ACTIVE_HIGH>;
  26                         linux,default-trigger = "mmc0";
  27                 };
  28
  29                 led-2 {
  30                         label = "TestLed602";
  31                         gpios = <&gpio4 10 GPIO_ACTIVE_HIGH>;
  32                         linux,default-trigger = "heartbeat";
  33                 };
  34         };
  35
  36         beeper {
  37                 compatible = "gpio-beeper";
  38                 pinctrl-names = "default";
  39                 pinctrl-0 = <&pinctrl_beeper>;
  40                 gpios = <&gpio5 3 GPIO_ACTIVE_HIGH>;
  41         };
  42
  43         /* Fixed clock dedicated to SPI CAN on carrier board */
  44         clk_xtal20: clk-xtal20 {
  45                 compatible = "fixed-clock";
  46                 #clock-cells = <0>;
  47                 clock-frequency = <20000000>;
  48         };
  49 };
  50
  51 &ecspi1 {
  52         #address-cells = <1>;
  53         #size-cells = <0>;
  54         pinctrl-names = "default";
  55         pinctrl-0 = <&pinctrl_ecspi1>;
  56         cs-gpios = <&gpio5 9 GPIO_ACTIVE_LOW>;
  57         status = "okay";
  58
  59         /* CAN controller on the baseboard */
  60         canfd: can@0 {
  61                 compatible = "microchip,mcp2518fd";
  62                 clocks = <&clk_xtal20>;
  63                 interrupt-parent = <&gpio1>;
  64                 interrupts = <8 IRQ_TYPE_EDGE_FALLING>;
  65                 reg = <0>;
  66                 spi-max-frequency = <2000000>;
  67         };
  68
  69 };
  70
  71 &ecspi2 {
  72         pinctrl-0 = <&pinctrl_ecspi2 &pinctrl_gpio1>;
  73         cs-gpios = <&gpio5 13 GPIO_ACTIVE_LOW>, <&gpio3 4 GPIO_ACTIVE_LOW>;
  74         status = "okay";
  75
  76         spidev@0 {
  77                 compatible = "menlo,m53cpld";
  78                 reg = <0>;
  79                 spi-max-frequency = <25000000>;
  80         };
  81
  82         spidev@1 {
  83                 compatible = "menlo,m53cpld";
  84                 reg = <1>;
  85                 spi-max-frequency = <25000000>;
  86         };
  87
  88 };
  89
  90 &ethphy0 {
  91         max-speed = <100>;
  92 };
  93
  94 &fec1 {
  95         status = "okay";
  96 };
  97
  98 &flexspi {
  99         status = "okay";
 100
 101         flash@0 {
 102                 reg = <0>;
 103                 #address-cells = <1>;
 104                 #size-cells = <1>;
 105                 compatible = "jedec,spi-nor";
 106                 spi-max-frequency = <66000000>;
 107                 spi-rx-bus-width = <4>;
 108                 spi-tx-bus-width = <4>;
 109         };
 110 };
 111
 112 &gpio1 {
 113         gpio-line-names =
 114                 "", "", "", "",
 115                 "", "", "", "",
 116                 "", "", "", "",
 117                 "", "", "", "",
 118                 "", "", "", "",
 119                 "", "", "", "",
 120                 "", "", "", "",
 121                 "", "", "", "";
 122 };
 123
 124 &gpio2 {
 125         gpio-line-names =
 126                 "", "", "", "",
 127                 "", "", "", "",
 128                 "", "", "", "",
 129                 "", "", "", "",
 130                 "", "", "", "",
 131                 "", "", "", "",
 132                 "", "", "", "",
 133                 "", "", "", "";
 134 };
 135
 136 &gpio3 {
 137         gpio-line-names =
 138                 "", "", "", "",
 139                 "", "", "", "",
 140                 "", "", "", "",
 141                 "", "", "", "",
 142                 "", "", "", "",
 143                 "", "", "DISP_reset", "KBD_intI",
 144                 "", "", "", "",
 145                 "", "", "", "";
 146 };
 147
 148 &gpio4 {
 149         /*
 150          * CPLD_D[n] is ARM_CPLD[n] in schematic
 151          * CPLD_int is SA_INTERRUPT in schematic
 152          * CPLD_reset is RESET_SOFT in schematic
 153          */
 154         gpio-line-names =
 155                 "CPLD_D[6]", "CPLD_int", "CPLD_reset", "",
 156                 "", "CPLD_D[7]", "", "",
 157                 "", "", "", "CPLD_D[5]",
 158                 "CPLD_D[4]", "CPLD_D[3]", "CPLD_D[2]", "CPLD_D[1]",
 159                 "CPLD_D[0]", "", "", "",
 160                 "", "", "", "",
 161                 "", "", "", "KBD_intK",
 162                 "", "", "", "";
 163 };
 164
 165 &gpio5 {
 166         gpio-line-names =
 167                 "", "", "", "",
 168                 "", "", "", "",
 169                 "", "", "", "",
 170                 "", "", "", "",
 171                 "", "", "", "",
 172                 "", "", "", "",
 173                 "", "", "", "",
 174                 "", "", "", "";
 175 };
 176
 177 &gpio_expander_21 {
 178         status = "okay";
 179 };
 180
 181 &hwmon {
 182         status = "okay";
 183 };
 184
 185 &i2c3 {
 186         status = "okay";
 187 };
 188
 189 &i2c4 {
 190         /* None of this is present on the SoM. */
 191         /delete-node/ bridge@2c;
 192         /delete-node/ hdmi@48;
 193         /delete-node/ touch@4a;
 194         /delete-node/ sensor@4f;
 195         /delete-node/ eeprom@50;
 196         /delete-node/ eeprom@57;
 197 };
 198
 199 &iomuxc {
 200         pinctrl-0 = <&pinctrl_gpio7>, <&pinctrl_gpio_hog1>,
 201                     <&pinctrl_gpio_hog2>, <&pinctrl_gpio_hog3>;
 202
 203         pinctrl_beeper: beepergrp {
 204                 fsl,pins = <
 205                         MX8MM_IOMUXC_SPDIF_TX_GPIO5_IO3                 0x1c4
 206                 >;
 207         };
 208
 209         pinctrl_ecspi1: ecspi1grp {
 210                 fsl,pins = <
 211                         MX8MM_IOMUXC_ECSPI1_SCLK_ECSPI1_SCLK            0x4
 212                         MX8MM_IOMUXC_ECSPI1_MOSI_ECSPI1_MOSI            0x4
 213                         MX8MM_IOMUXC_ECSPI1_MISO_ECSPI1_MISO            0x1c4
 214                         MX8MM_IOMUXC_ECSPI1_SS0_GPIO5_IO9               0x1c4
 215                 >;
 216         };
 217
 218         pinctrl_led: ledgrp {
 219                 fsl,pins = <
 220                         MX8MM_IOMUXC_SAI1_TXD6_GPIO4_IO18               0x1c4
 221                         MX8MM_IOMUXC_SAI1_TXFS_GPIO4_IO10               0x1c4
 222                 >;
 223         };
 224
 225         pinctrl_uart4_rts: uart4rtsgrp {
 226                 fsl,pins = <
 227                         /* SODIMM 222 */
 228                         MX8MM_IOMUXC_GPIO1_IO09_GPIO1_IO9               0x184
 229                 >;
 230         };
 231 };
 232
 233 &pinctrl_gpio1 {
 234         fsl,pins = <
 235                 /* SODIMM 206 */
 236                 MX8MM_IOMUXC_NAND_CE3_B_GPIO3_IO4                       0x1c4
 237         >;
 238 };
 239
 240 &pinctrl_gpio_hog1 {
 241         fsl,pins = <
 242                 /* SODIMM 88 */
 243                 MX8MM_IOMUXC_SAI1_MCLK_GPIO4_IO20                       0x1c4
 244                 /* CPLD_int */
 245                 MX8MM_IOMUXC_SAI1_RXC_GPIO4_IO1                         0x1c4
 246                 /* CPLD_reset */
 247                 MX8MM_IOMUXC_SAI1_RXD0_GPIO4_IO2                        0x1c4
 248                 /* SODIMM 94 */
 249                 MX8MM_IOMUXC_SAI1_RXD1_GPIO4_IO3                        0x1c4
 250                 /* SODIMM 96 */
 251                 MX8MM_IOMUXC_SAI1_RXD2_GPIO4_IO4                        0x1c4
 252                 /* CPLD_D[7] */
 253                 MX8MM_IOMUXC_SAI1_RXD3_GPIO4_IO5                        0x1c4
 254                 /* CPLD_D[6] */
 255                 MX8MM_IOMUXC_SAI1_RXFS_GPIO4_IO0                        0x1c4
 256                 /* CPLD_D[5] */
 257                 MX8MM_IOMUXC_SAI1_TXC_GPIO4_IO11                        0x1c4
 258                 /* CPLD_D[4] */
 259                 MX8MM_IOMUXC_SAI1_TXD0_GPIO4_IO12                       0x1c4
 260                 /* CPLD_D[3] */
 261                 MX8MM_IOMUXC_SAI1_TXD1_GPIO4_IO13                       0x1c4
 262                 /* CPLD_D[2] */
 263                 MX8MM_IOMUXC_SAI1_TXD2_GPIO4_IO14                       0x1c4
 264                 /* CPLD_D[1] */
 265                 MX8MM_IOMUXC_SAI1_TXD3_GPIO4_IO15                       0x1c4
 266                 /* CPLD_D[0] */
 267                 MX8MM_IOMUXC_SAI1_TXD4_GPIO4_IO16                       0x1c4
 268                 /* KBD_intK */
 269                 MX8MM_IOMUXC_SAI2_MCLK_GPIO4_IO27                       0x1c4
 270                 /* DISP_reset */
 271                 MX8MM_IOMUXC_SAI5_RXD1_GPIO3_IO22                       0x1c4
 272                 /* KBD_intI */
 273                 MX8MM_IOMUXC_SAI5_RXD2_GPIO3_IO23                       0x1c4
 274                 /* SODIMM 46 */
 275                 MX8MM_IOMUXC_SAI5_RXD3_GPIO3_IO24                       0x1c4
 276         >;
 277 };
 278
 279 &pinctrl_uart1 {
 280         fsl,pins = <
 281                 /* SODIMM 149 */
 282                 MX8MM_IOMUXC_SAI2_RXFS_UART1_DCE_TX                     0x1c4
 283                 /* SODIMM 147 */
 284                 MX8MM_IOMUXC_SAI2_RXC_UART1_DCE_RX                      0x1c4
 285                 /* SODIMM 210 */
 286                 MX8MM_IOMUXC_UART3_RXD_UART1_DTE_RTS_B                  0x1c4
 287                 /* SODIMM 212 */
 288                 MX8MM_IOMUXC_UART3_TXD_UART1_DTE_CTS_B                  0x1c4
 289         >;
 290 };
 291
 292 &reg_usb_otg1_vbus {
 293         /delete-property/ enable-active-high;
 294         gpio = <&gpio1 12 GPIO_ACTIVE_LOW>;
 295 };
 296
 297 &reg_usb_otg2_vbus {
 298         /delete-property/ enable-active-high;
 299         gpio = <&gpio1 14 GPIO_ACTIVE_LOW>;
 300 };
 301
 302 &sai2 {
 303         status = "disabled";
 304 };
 305
 306 &uart1 {
 307         uart-has-rtscts;
 308         status = "okay";
 309 };
 310
 311 &uart2 {
 312         status = "okay";
 313 };
 314
 315 &uart4 {
 316         pinctrl-0 = <&pinctrl_uart4 &pinctrl_uart4_rts>;
 317         linux,rs485-enabled-at-boot-time;
 318         rts-gpios = <&gpio1 9 GPIO_ACTIVE_HIGH>;
 319         status = "okay";
 320 };
 321
 322 &usbotg1 {
 323         dr_mode = "peripheral";
 324         status = "okay";
 325 };
 326
 327 &usbotg2 {
 328         dr_mode = "host";
 329         status = "okay";
 330 };
 331
 332 &usdhc2 {
 333         status = "okay";
 334 };