arch/arm/mach-spear/spear3xx.c

   1 /*
   2  * arch/arm/mach-spear3xx/spear3xx.c
   3  *
   4  * SPEAr3XX machines common source file
   5  *
   6  * Copyright (C) 2009-2012 ST Microelectronics
   7  * Viresh Kumar <viresh.linux@gmail.com>
   8  *
   9  * This file is licensed under the terms of the GNU General Public
  10  * License version 2. This program is licensed "as is" without any
  11  * warranty of any kind, whether express or implied.
  12  */
  13
  14 #define pr_fmt(fmt) "SPEAr3xx: " fmt
  15
  16 #include <linux/amba/pl022.h>
  17 #include <linux/amba/pl080.h>
  18 #include <linux/clk.h>
  19 #include <linux/io.h>
  20 #include <asm/mach/map.h>
  21 #include "pl080.h"
  22 #include "generic.h"
  23 #include <mach/spear.h>
  24 #include <mach/misc_regs.h>
  25
  26 /* ssp device registration */
  27 struct pl022_ssp_controller pl022_plat_data = {
  28         .bus_id = 0,
  29         .enable_dma = 1,
  30         .dma_filter = pl08x_filter_id,
  31         .dma_tx_param = "ssp0_tx",
  32         .dma_rx_param = "ssp0_rx",
  33         /*
  34          * This is number of spi devices that can be connected to spi. There are
  35          * two type of chipselects on which slave devices can work. One is chip
  36          * select provided by spi masters other is controlled through external
  37          * gpio's. We can't use chipselect provided from spi master (because as
  38          * soon as FIFO becomes empty, CS is disabled and transfer ends). So
  39          * this number now depends on number of gpios available for spi. each
  40          * slave on each master requires a separate gpio pin.
  41          */
  42         .num_chipselect = 2,
  43 };
  44
  45 /* dmac device registration */
  46 struct pl08x_platform_data pl080_plat_data = {
  47         .memcpy_channel = {
  48                 .bus_id = "memcpy",
  49                 .cctl_memcpy =
  50                         (PL080_BSIZE_16 << PL080_CONTROL_SB_SIZE_SHIFT | \
  51                         PL080_BSIZE_16 << PL080_CONTROL_DB_SIZE_SHIFT | \
  52                         PL080_WIDTH_32BIT << PL080_CONTROL_SWIDTH_SHIFT | \
  53                         PL080_WIDTH_32BIT << PL080_CONTROL_DWIDTH_SHIFT | \
  54                         PL080_CONTROL_PROT_BUFF | PL080_CONTROL_PROT_CACHE | \
  55                         PL080_CONTROL_PROT_SYS),
  56         },
  57         .lli_buses = PL08X_AHB1,
  58         .mem_buses = PL08X_AHB1,
  59         .get_xfer_signal = pl080_get_signal,
  60         .put_xfer_signal = pl080_put_signal,
  61 };
  62
  63 /*
  64  * Following will create 16MB static virtual/physical mappings
  65  * PHYSICAL             VIRTUAL
  66  * 0xD0000000           0xFD000000
  67  * 0xFC000000           0xFC000000
  68  */
  69 struct map_desc spear3xx_io_desc[] __initdata = {
  70         {
  71                 .virtual        = (unsigned long)VA_SPEAR_ICM1_2_BASE,
  72                 .pfn            = __phys_to_pfn(SPEAR_ICM1_2_BASE),
  73                 .length         = SZ_16M,
  74                 .type           = MT_DEVICE
  75         }, {
  76                 .virtual        = (unsigned long)VA_SPEAR_ICM3_SMI_CTRL_BASE,
  77                 .pfn            = __phys_to_pfn(SPEAR_ICM3_SMI_CTRL_BASE),
  78                 .length         = SZ_16M,
  79                 .type           = MT_DEVICE
  80         },
  81 };
  82
  83 /* This will create static memory mapping for selected devices */
  84 void __init spear3xx_map_io(void)
  85 {
  86         iotable_init(spear3xx_io_desc, ARRAY_SIZE(spear3xx_io_desc));
  87 }
  88
  89 void __init spear3xx_timer_init(void)
  90 {
  91         char pclk_name[] = "pll3_clk";
  92         struct clk *gpt_clk, *pclk;
  93
  94         spear3xx_clk_init(MISC_BASE, VA_SPEAR320_SOC_CONFIG_BASE);
  95
  96         /* get the system timer clock */
  97         gpt_clk = clk_get_sys("gpt0", NULL);
  98         if (IS_ERR(gpt_clk)) {
  99                 pr_err("%s:couldn't get clk for gpt\n", __func__);
 100                 BUG();
 101         }
 102
 103         /* get the suitable parent clock for timer*/
 104         pclk = clk_get(NULL, pclk_name);
 105         if (IS_ERR(pclk)) {
 106                 pr_err("%s:couldn't get %s as parent for gpt\n",
 107                                 __func__, pclk_name);
 108                 BUG();
 109         }
 110
 111         clk_set_parent(gpt_clk, pclk);
 112         clk_put(gpt_clk);
 113         clk_put(pclk);
 114
 115         spear_setup_of_timer();
 116 }