arch/arm/dts/zynqmp-zcu104-revC.dts

   1 // SPDX-License-Identifier: GPL-2.0+
   2 /*
   3  * dts file for Xilinx ZynqMP ZCU104
   4  *
   5  * (C) Copyright 2017 - 2018, Xilinx, Inc.
   6  *
   7  * Michal Simek <michal.simek@xilinx.com>
   8  */
   9
  10 /dts-v1/;
  11
  12 #include "zynqmp.dtsi"
  13 #include "zynqmp-clk-ccf.dtsi"
  14 #include <dt-bindings/gpio/gpio.h>
  15 #include <dt-bindings/phy/phy.h>
  16
  17 / {
  18         model = "ZynqMP ZCU104 RevC";
  19         compatible = "xlnx,zynqmp-zcu104-revC", "xlnx,zynqmp-zcu104", "xlnx,zynqmp";
  20
  21         aliases {
  22                 ethernet0 = &gem3;
  23                 gpio0 = &gpio;
  24                 i2c0 = &i2c1;
  25                 mmc0 = &sdhci1;
  26                 rtc0 = &rtc;
  27                 serial0 = &uart0;
  28                 serial1 = &uart1;
  29                 serial2 = &dcc;
  30                 spi0 = &qspi;
  31                 usb0 = &usb0;
  32         };
  33
  34         chosen {
  35                 bootargs = "earlycon";
  36                 stdout-path = "serial0:115200n8";
  37         };
  38
  39         memory@0 {
  40                 device_type = "memory";
  41                 reg = <0x0 0x0 0x0 0x80000000>;
  42         };
  43 };
  44
  45 &can1 {
  46         status = "okay";
  47 };
  48
  49 &dcc {
  50         status = "okay";
  51 };
  52
  53 &gem3 {
  54         status = "okay";
  55         phy-handle = <&phy0>;
  56         phy-mode = "rgmii-id";
  57         phy0: phy@c {
  58                 reg = <0xc>;
  59                 ti,rx-internal-delay = <0x8>;
  60                 ti,tx-internal-delay = <0xa>;
  61                 ti,fifo-depth = <0x1>;
  62         };
  63 };
  64
  65 &gpio {
  66         status = "okay";
  67 };
  68
  69 &gpu {
  70         status = "okay";
  71 };
  72
  73 &i2c1 {
  74         status = "okay";
  75         clock-frequency = <400000>;
  76
  77         tca6416_u97: gpio@20 {
  78                 compatible = "ti,tca6416";
  79                 reg = <0x20>;
  80                 gpio-controller;
  81                 #gpio-cells = <2>;
  82                 /*
  83                  * IRQ not connected
  84                  * Lines:
  85                  * 0 - IRPS5401_ALERT_B
  86                  * 1 - HDMI_8T49N241_INT_ALM
  87                  * 2 - MAX6643_OT_B
  88                  * 3 - MAX6643_FANFAIL_B
  89                  * 5 - IIC_MUX_RESET_B
  90                  * 6 - GEM3_EXP_RESET_B
  91                  * 7 - FMC_LPC_PRSNT_M2C_B
  92                  * 4, 10 - 17 - not connected
  93                  */
  94         };
  95
  96         /* Another connection to this bus via PL i2c via PCA9306 - u45 */
  97         i2c-mux@74 { /* u34 */
  98                 compatible = "nxp,pca9548";
  99                 #address-cells = <1>;
 100                 #size-cells = <0>;
 101                 reg = <0x74>;
 102                 i2c@0 {
 103                         #address-cells = <1>;
 104                         #size-cells = <0>;
 105                         reg = <0>;
 106                         /*
 107                          * IIC_EEPROM 1kB memory which uses 256B blocks
 108                          * where every block has different address.
 109                          *    0 - 256B address 0x54
 110                          * 256B - 512B address 0x55
 111                          * 512B - 768B address 0x56
 112                          * 768B - 1024B address 0x57
 113                          */
 114                         eeprom: eeprom@54 { /* u23 */
 115                                 compatible = "atmel,24c08";
 116                                 reg = <0x54>;
 117                                 #address-cells = <1>;
 118                                 #size-cells = <1>;
 119                         };
 120                 };
 121
 122                 i2c@1 {
 123                         #address-cells = <1>;
 124                         #size-cells = <0>;
 125                         reg = <1>;
 126                         clock_8t49n287: clock-generator@6c { /* 8T49N287 - u182 */
 127                                 compatible = "idt,8t49n287";
 128                                 reg = <0x6c>;
 129                         };
 130                 };
 131
 132                 i2c@2 {
 133                         #address-cells = <1>;
 134                         #size-cells = <0>;
 135                         reg = <2>;
 136                         irps5401_43: irps54012@43 { /* IRPS5401 - u175 */
 137                                 #clock-cells = <0>;
 138                                 compatible = "infineon,irps5401";
 139                                 reg = <0x43>;
 140                         };
 141                         irps5401_4d: irps54012@4d { /* IRPS5401 - u180 */
 142                                 #clock-cells = <0>;
 143                                 compatible = "infineon,irps5401";
 144                                 reg = <0x4d>;
 145                         };
 146                 };
 147
 148                 i2c@3 {
 149                         #address-cells = <1>;
 150                         #size-cells = <0>;
 151                         reg = <3>;
 152                         ina226@40 { /* u183 */
 153                                 compatible = "ti,ina226";
 154                                 reg = <0x40>;
 155                                 shunt-resistor = <5000>;
 156                         };
 157                 };
 158
 159                 i2c@5 {
 160                         #address-cells = <1>;
 161                         #size-cells = <0>;
 162                         reg = <5>;
 163                 };
 164
 165                 i2c@7 {
 166                         #address-cells = <1>;
 167                         #size-cells = <0>;
 168                         reg = <7>;
 169                 };
 170
 171                 /* 4, 6 not connected */
 172         };
 173 };
 174
 175 &qspi {
 176         status = "okay";
 177         flash@0 {
 178                 compatible = "m25p80", "spi-flash"; /* n25q512a 128MiB */
 179                 #address-cells = <1>;
 180                 #size-cells = <1>;
 181                 reg = <0x0>;
 182                 spi-tx-bus-width = <1>;
 183                 spi-rx-bus-width = <4>;
 184                 spi-max-frequency = <108000000>; /* Based on DC1 spec */
 185                 partition@qspi-fsbl-uboot { /* for testing purpose */
 186                         label = "qspi-fsbl-uboot";
 187                         reg = <0x0 0x100000>;
 188                 };
 189                 partition@qspi-linux { /* for testing purpose */
 190                         label = "qspi-linux";
 191                         reg = <0x100000 0x500000>;
 192                 };
 193                 partition@qspi-device-tree { /* for testing purpose */
 194                         label = "qspi-device-tree";
 195                         reg = <0x600000 0x20000>;
 196                 };
 197                 partition@qspi-rootfs { /* for testing purpose */
 198                         label = "qspi-rootfs";
 199                         reg = <0x620000 0x5E0000>;
 200                 };
 201         };
 202 };
 203
 204 &rtc {
 205         status = "okay";
 206 };
 207
 208 &sata {
 209         status = "okay";
 210         /* SATA OOB timing settings */
 211         ceva,p0-cominit-params = /bits/ 8 <0x18 0x40 0x18 0x28>;
 212         ceva,p0-comwake-params = /bits/ 8 <0x06 0x14 0x08 0x0E>;
 213         ceva,p0-burst-params = /bits/ 8 <0x13 0x08 0x4A 0x06>;
 214         ceva,p0-retry-params = /bits/ 16 <0x96A4 0x3FFC>;
 215         ceva,p1-cominit-params = /bits/ 8 <0x18 0x40 0x18 0x28>;
 216         ceva,p1-comwake-params = /bits/ 8 <0x06 0x14 0x08 0x0E>;
 217         ceva,p1-burst-params = /bits/ 8 <0x13 0x08 0x4A 0x06>;
 218         ceva,p1-retry-params = /bits/ 16 <0x96A4 0x3FFC>;
 219         phy-names = "sata-phy";
 220         phys = <&lane3 PHY_TYPE_SATA 1 1 125000000>;
 221 };
 222
 223 /* SD1 with level shifter */
 224 &sdhci1 {
 225         status = "okay";
 226         no-1-8-v;
 227         xlnx,mio_bank = <1>;
 228         disable-wp;
 229 };
 230
 231 &serdes {
 232         status = "okay";
 233 };
 234
 235 &uart0 {
 236         status = "okay";
 237 };
 238
 239 &uart1 {
 240         status = "okay";
 241 };
 242
 243 /* ULPI SMSC USB3320 */
 244 &usb0 {
 245         status = "okay";
 246 };
 247
 248 &dwc3_0 {
 249         status = "okay";
 250         dr_mode = "host";
 251         snps,usb3_lpm_capable;
 252         phy-names = "usb3-phy";
 253         phys = <&lane2 PHY_TYPE_USB3 0 2 26000000>;
 254         maximum-speed = "super-speed";
 255 };
 256
 257 &watchdog0 {
 258         status = "okay";
 259 };
 260
 261 &xilinx_ams {
 262         status = "okay";
 263 };
 264
 265 &ams_ps {
 266         status = "okay";
 267 };
 268
 269 &ams_pl {
 270         status = "okay";
 271 };