arch/arm/dts/salvator-common.dtsi

   1 // SPDX-License-Identifier: GPL-2.0
   2 /*
   3  * Device Tree Source for common parts of Salvator-X board variants
   4  *
   5  * Copyright (C) 2015-2016 Renesas Electronics Corp.
   6  */
   7
   8 /*
   9  * SSI-AK4613
  10  *
  11  * This command is required when Playback/Capture
  12  *
  13  *      amixer set "DVC Out" 100%
  14  *      amixer set "DVC In" 100%
  15  *
  16  * You can use Mute
  17  *
  18  *      amixer set "DVC Out Mute" on
  19  *      amixer set "DVC In Mute" on
  20  *
  21  * You can use Volume Ramp
  22  *
  23  *      amixer set "DVC Out Ramp Up Rate"   "0.125 dB/64 steps"
  24  *      amixer set "DVC Out Ramp Down Rate" "0.125 dB/512 steps"
  25  *      amixer set "DVC Out Ramp" on
  26  *      aplay xxx.wav &
  27  *      amixer set "DVC Out"  80%  // Volume Down
  28  *      amixer set "DVC Out" 100%  // Volume Up
  29  */
  30
  31 #include <dt-bindings/gpio/gpio.h>
  32
  33 / {
  34         aliases {
  35                 serial0 = &scif2;
  36                 serial1 = &hscif1;
  37                 ethernet0 = &avb;
  38         };
  39
  40         chosen {
  41                 bootargs = "ignore_loglevel rw root=/dev/nfs ip=dhcp";
  42                 stdout-path = "serial0:115200n8";
  43         };
  44
  45         audio_clkout: audio-clkout {
  46                 /*
  47                  * This is same as <&rcar_sound 0>
  48                  * but needed to avoid cs2000/rcar_sound probe dead-lock
  49                  */
  50                 compatible = "fixed-clock";
  51                 #clock-cells = <0>;
  52                 clock-frequency = <12288000>;
  53         };
  54
  55         backlight: backlight {
  56                 compatible = "pwm-backlight";
  57                 pwms = <&pwm1 0 50000>;
  58
  59                 brightness-levels = <256 128 64 16 8 4 0>;
  60                 default-brightness-level = <6>;
  61
  62                 power-supply = <&reg_12v>;
  63                 enable-gpios = <&gpio6 7 GPIO_ACTIVE_HIGH>;
  64         };
  65
  66         cvbs-in {
  67                 compatible = "composite-video-connector";
  68                 label = "CVBS IN";
  69
  70                 port {
  71                         cvbs_con: endpoint {
  72                                 remote-endpoint = <&adv7482_ain7>;
  73                         };
  74                 };
  75         };
  76
  77         hdmi-in {
  78                 compatible = "hdmi-connector";
  79                 label = "HDMI IN";
  80                 type = "a";
  81
  82                 port {
  83                         hdmi_in_con: endpoint {
  84                                 remote-endpoint = <&adv7482_hdmi>;
  85                         };
  86                 };
  87         };
  88
  89         reg_1p8v: regulator0 {
  90                 compatible = "regulator-fixed";
  91                 regulator-name = "fixed-1.8V";
  92                 regulator-min-microvolt = <1800000>;
  93                 regulator-max-microvolt = <1800000>;
  94                 regulator-boot-on;
  95                 regulator-always-on;
  96         };
  97
  98         reg_3p3v: regulator1 {
  99                 compatible = "regulator-fixed";
 100                 regulator-name = "fixed-3.3V";
 101                 regulator-min-microvolt = <3300000>;
 102                 regulator-max-microvolt = <3300000>;
 103                 regulator-boot-on;
 104                 regulator-always-on;
 105         };
 106
 107         reg_12v: regulator2 {
 108                 compatible = "regulator-fixed";
 109                 regulator-name = "fixed-12V";
 110                 regulator-min-microvolt = <12000000>;
 111                 regulator-max-microvolt = <12000000>;
 112                 regulator-boot-on;
 113                 regulator-always-on;
 114         };
 115
 116         sound_card: sound {
 117                 compatible = "audio-graph-card";
 118
 119                 label = "rcar-sound";
 120
 121                 dais = <&rsnd_port0>;
 122         };
 123
 124         vbus0_usb2: regulator-vbus0-usb2 {
 125                 compatible = "regulator-fixed";
 126
 127                 regulator-name = "USB20_VBUS0";
 128                 regulator-min-microvolt = <5000000>;
 129                 regulator-max-microvolt = <5000000>;
 130
 131                 gpio = <&gpio6 16 GPIO_ACTIVE_HIGH>;
 132                 enable-active-high;
 133         };
 134
 135         vcc_sdhi0: regulator-vcc-sdhi0 {
 136                 compatible = "regulator-fixed";
 137
 138                 regulator-name = "SDHI0 Vcc";
 139                 regulator-min-microvolt = <3300000>;
 140                 regulator-max-microvolt = <3300000>;
 141
 142                 gpio = <&gpio5 2 GPIO_ACTIVE_HIGH>;
 143                 enable-active-high;
 144         };
 145
 146         vccq_sdhi0: regulator-vccq-sdhi0 {
 147                 compatible = "regulator-gpio";
 148
 149                 regulator-name = "SDHI0 VccQ";
 150                 regulator-min-microvolt = <1800000>;
 151                 regulator-max-microvolt = <3300000>;
 152
 153                 gpios = <&gpio5 1 GPIO_ACTIVE_HIGH>;
 154                 gpios-states = <1>;
 155                 states = <3300000 1
 156                           1800000 0>;
 157         };
 158
 159         vcc_sdhi3: regulator-vcc-sdhi3 {
 160                 compatible = "regulator-fixed";
 161
 162                 regulator-name = "SDHI3 Vcc";
 163                 regulator-min-microvolt = <3300000>;
 164                 regulator-max-microvolt = <3300000>;
 165
 166                 gpio = <&gpio3 15 GPIO_ACTIVE_HIGH>;
 167                 enable-active-high;
 168         };
 169
 170         vccq_sdhi3: regulator-vccq-sdhi3 {
 171                 compatible = "regulator-gpio";
 172
 173                 regulator-name = "SDHI3 VccQ";
 174                 regulator-min-microvolt = <1800000>;
 175                 regulator-max-microvolt = <3300000>;
 176
 177                 gpios = <&gpio3 14 GPIO_ACTIVE_HIGH>;
 178                 gpios-states = <1>;
 179                 states = <3300000 1
 180                           1800000 0>;
 181         };
 182
 183         hdmi0-out {
 184                 compatible = "hdmi-connector";
 185                 label = "HDMI0 OUT";
 186                 type = "a";
 187
 188                 port {
 189                         hdmi0_con: endpoint {
 190                         };
 191                 };
 192         };
 193
 194         hdmi1-out {
 195                 compatible = "hdmi-connector";
 196                 label = "HDMI1 OUT";
 197                 type = "a";
 198
 199                 port {
 200                         hdmi1_con: endpoint {
 201                         };
 202                 };
 203         };
 204
 205         vga {
 206                 compatible = "vga-connector";
 207
 208                 port {
 209                         vga_in: endpoint {
 210                                 remote-endpoint = <&adv7123_out>;
 211                         };
 212                 };
 213         };
 214
 215         vga-encoder {
 216                 compatible = "adi,adv7123";
 217
 218                 ports {
 219                         #address-cells = <1>;
 220                         #size-cells = <0>;
 221
 222                         port@0 {
 223                                 reg = <0>;
 224                                 adv7123_in: endpoint {
 225                                         remote-endpoint = <&du_out_rgb>;
 226                                 };
 227                         };
 228                         port@1 {
 229                                 reg = <1>;
 230                                 adv7123_out: endpoint {
 231                                         remote-endpoint = <&vga_in>;
 232                                 };
 233                         };
 234                 };
 235         };
 236
 237         x12_clk: x12 {
 238                 compatible = "fixed-clock";
 239                 #clock-cells = <0>;
 240                 clock-frequency = <24576000>;
 241         };
 242
 243         /* External DU dot clocks */
 244         x21_clk: x21-clock {
 245                 compatible = "fixed-clock";
 246                 #clock-cells = <0>;
 247                 clock-frequency = <33000000>;
 248         };
 249
 250         x22_clk: x22-clock {
 251                 compatible = "fixed-clock";
 252                 #clock-cells = <0>;
 253                 clock-frequency = <33000000>;
 254         };
 255
 256         x23_clk: x23-clock {
 257                 compatible = "fixed-clock";
 258                 #clock-cells = <0>;
 259                 clock-frequency = <25000000>;
 260         };
 261 };
 262
 263 &audio_clk_a {
 264         clock-frequency = <22579200>;
 265 };
 266
 267 &avb {
 268         pinctrl-0 = <&avb_pins>;
 269         pinctrl-names = "default";
 270         phy-handle = <&phy0>;
 271         phy-mode = "rgmii-txid";
 272         status = "okay";
 273
 274         phy0: ethernet-phy@0 {
 275                 rxc-skew-ps = <1500>;
 276                 reg = <0>;
 277                 interrupt-parent = <&gpio2>;
 278                 interrupts = <11 IRQ_TYPE_LEVEL_LOW>;
 279                 reset-gpios = <&gpio2 10 GPIO_ACTIVE_LOW>;
 280         };
 281 };
 282
 283 &csi20 {
 284         status = "okay";
 285
 286         ports {
 287                 port@0 {
 288                         reg = <0>;
 289                         csi20_in: endpoint {
 290                                 clock-lanes = <0>;
 291                                 data-lanes = <1>;
 292                                 remote-endpoint = <&adv7482_txb>;
 293                         };
 294                 };
 295         };
 296 };
 297
 298 &csi40 {
 299         status = "okay";
 300
 301         ports {
 302                 port@0 {
 303                         reg = <0>;
 304
 305                         csi40_in: endpoint {
 306                                 clock-lanes = <0>;
 307                                 data-lanes = <1 2 3 4>;
 308                                 remote-endpoint = <&adv7482_txa>;
 309                         };
 310                 };
 311         };
 312 };
 313
 314 &du {
 315         pinctrl-0 = <&du_pins>;
 316         pinctrl-names = "default";
 317         status = "okay";
 318
 319         ports {
 320                 port@0 {
 321                         endpoint {
 322                                 remote-endpoint = <&adv7123_in>;
 323                         };
 324                 };
 325         };
 326 };
 327
 328 &ehci0 {
 329         dr_mode = "otg";
 330         status = "okay";
 331 };
 332
 333 &ehci1 {
 334         status = "okay";
 335 };
 336
 337 &extalr_clk {
 338         clock-frequency = <32768>;
 339 };
 340
 341 &hscif1 {
 342         pinctrl-0 = <&hscif1_pins>;
 343         pinctrl-names = "default";
 344
 345         uart-has-rtscts;
 346         /* Please only enable hscif1 or scif1 */
 347         status = "okay";
 348 };
 349
 350 &hsusb {
 351         dr_mode = "otg";
 352         status = "okay";
 353 };
 354
 355 &i2c2 {
 356         pinctrl-0 = <&i2c2_pins>;
 357         pinctrl-names = "default";
 358
 359         status = "okay";
 360
 361         clock-frequency = <100000>;
 362
 363         ak4613: codec@10 {
 364                 compatible = "asahi-kasei,ak4613";
 365                 #sound-dai-cells = <0>;
 366                 reg = <0x10>;
 367                 clocks = <&rcar_sound 3>;
 368
 369                 asahi-kasei,in1-single-end;
 370                 asahi-kasei,in2-single-end;
 371                 asahi-kasei,out1-single-end;
 372                 asahi-kasei,out2-single-end;
 373                 asahi-kasei,out3-single-end;
 374                 asahi-kasei,out4-single-end;
 375                 asahi-kasei,out5-single-end;
 376                 asahi-kasei,out6-single-end;
 377
 378                 port {
 379                         ak4613_endpoint: endpoint {
 380                                 remote-endpoint = <&rsnd_endpoint0>;
 381                         };
 382                 };
 383         };
 384
 385         cs2000: clk_multiplier@4f {
 386                 #clock-cells = <0>;
 387                 compatible = "cirrus,cs2000-cp";
 388                 reg = <0x4f>;
 389                 clocks = <&audio_clkout>, <&x12_clk>;
 390                 clock-names = "clk_in", "ref_clk";
 391
 392                 assigned-clocks = <&cs2000>;
 393                 assigned-clock-rates = <24576000>; /* 1/1 divide */
 394         };
 395 };
 396
 397 &i2c4 {
 398         status = "okay";
 399
 400         pca9654: gpio@20 {
 401                 compatible = "onnn,pca9654";
 402                 reg = <0x20>;
 403                 gpio-controller;
 404                 #gpio-cells = <2>;
 405         };
 406
 407         csa_vdd: adc@7c {
 408                 compatible = "maxim,max9611";
 409                 reg = <0x7c>;
 410
 411                 shunt-resistor-micro-ohms = <5000>;
 412         };
 413
 414         csa_dvfs: adc@7f {
 415                 compatible = "maxim,max9611";
 416                 reg = <0x7f>;
 417
 418                 shunt-resistor-micro-ohms = <5000>;
 419         };
 420
 421         video-receiver@70 {
 422                 compatible = "adi,adv7482";
 423                 reg = <0x70>;
 424
 425                 #address-cells = <1>;
 426                 #size-cells = <0>;
 427
 428                 interrupt-parent = <&gpio6>;
 429                 interrupt-names = "intrq1", "intrq2";
 430                 interrupts = <30 IRQ_TYPE_LEVEL_LOW>,
 431                              <31 IRQ_TYPE_LEVEL_LOW>;
 432
 433                 port@7 {
 434                         reg = <7>;
 435
 436                         adv7482_ain7: endpoint {
 437                                 remote-endpoint = <&cvbs_con>;
 438                         };
 439                 };
 440
 441                 port@8 {
 442                         reg = <8>;
 443
 444                         adv7482_hdmi: endpoint {
 445                                 remote-endpoint = <&hdmi_in_con>;
 446                         };
 447                 };
 448
 449                 port@a {
 450                         reg = <10>;
 451
 452                         adv7482_txa: endpoint {
 453                                 clock-lanes = <0>;
 454                                 data-lanes = <1 2 3 4>;
 455                                 remote-endpoint = <&csi40_in>;
 456                         };
 457                 };
 458
 459                 port@b {
 460                         reg = <11>;
 461
 462                         adv7482_txb: endpoint {
 463                                 clock-lanes = <0>;
 464                                 data-lanes = <1>;
 465                                 remote-endpoint = <&csi20_in>;
 466                         };
 467                 };
 468         };
 469 };
 470
 471 &i2c_dvfs {
 472         status = "okay";
 473
 474         pmic: pmic@30 {
 475                 pinctrl-0 = <&irq0_pins>;
 476                 pinctrl-names = "default";
 477
 478                 compatible = "rohm,bd9571mwv";
 479                 reg = <0x30>;
 480                 interrupt-parent = <&intc_ex>;
 481                 interrupts = <0 IRQ_TYPE_LEVEL_LOW>;
 482                 interrupt-controller;
 483                 #interrupt-cells = <2>;
 484                 gpio-controller;
 485                 #gpio-cells = <2>;
 486                 rohm,ddr-backup-power = <0xf>;
 487                 rohm,rstbmode-level;
 488
 489                 regulators {
 490                         dvfs: dvfs {
 491                                 regulator-name = "dvfs";
 492                                 regulator-min-microvolt = <750000>;
 493                                 regulator-max-microvolt = <1030000>;
 494                                 regulator-boot-on;
 495                                 regulator-always-on;
 496                         };
 497                 };
 498         };
 499
 500         eeprom@50 {
 501                 compatible = "rohm,br24t01", "atmel,24c01";
 502                 reg = <0x50>;
 503                 pagesize = <8>;
 504         };
 505 };
 506
 507 &ohci0 {
 508         dr_mode = "otg";
 509         status = "okay";
 510 };
 511
 512 &ohci1 {
 513         status = "okay";
 514 };
 515
 516 &pcie_bus_clk {
 517         clock-frequency = <100000000>;
 518 };
 519
 520 &pciec0 {
 521         status = "okay";
 522 };
 523
 524 &pciec1 {
 525         status = "okay";
 526 };
 527
 528 &pfc {
 529         pinctrl-0 = <&scif_clk_pins>;
 530         pinctrl-names = "default";
 531
 532         avb_pins: avb {
 533                 mux {
 534                         groups = "avb_link", "avb_mdio", "avb_mii";
 535                         function = "avb";
 536                 };
 537
 538                 pins_mdio {
 539                         groups = "avb_mdio";
 540                         drive-strength = <24>;
 541                 };
 542
 543                 pins_mii_tx {
 544                         pins = "PIN_AVB_TX_CTL", "PIN_AVB_TXC", "PIN_AVB_TD0",
 545                                "PIN_AVB_TD1", "PIN_AVB_TD2", "PIN_AVB_TD3";
 546                         drive-strength = <12>;
 547                 };
 548         };
 549
 550         du_pins: du {
 551                 groups = "du_rgb888", "du_sync", "du_oddf", "du_clk_out_0";
 552                 function = "du";
 553         };
 554
 555         hscif1_pins: hscif1 {
 556                 groups = "hscif1_data_a", "hscif1_ctrl_a";
 557                 function = "hscif1";
 558         };
 559
 560         i2c2_pins: i2c2 {
 561                 groups = "i2c2_a";
 562                 function = "i2c2";
 563         };
 564
 565         irq0_pins: irq0 {
 566                 groups = "intc_ex_irq0";
 567                 function = "intc_ex";
 568         };
 569
 570         pwm1_pins: pwm1 {
 571                 groups = "pwm1_a";
 572                 function = "pwm1";
 573         };
 574
 575         scif1_pins: scif1 {
 576                 groups = "scif1_data_a", "scif1_ctrl";
 577                 function = "scif1";
 578         };
 579
 580         scif2_pins: scif2 {
 581                 groups = "scif2_data_a";
 582                 function = "scif2";
 583         };
 584
 585         scif_clk_pins: scif_clk {
 586                 groups = "scif_clk_a";
 587                 function = "scif_clk";
 588         };
 589
 590         sdhi0_pins: sd0 {
 591                 groups = "sdhi0_data4", "sdhi0_ctrl";
 592                 function = "sdhi0";
 593                 power-source = <3300>;
 594         };
 595
 596         sdhi0_pins_uhs: sd0_uhs {
 597                 groups = "sdhi0_data4", "sdhi0_ctrl";
 598                 function = "sdhi0";
 599                 power-source = <1800>;
 600         };
 601
 602         sdhi2_pins: sd2 {
 603                 groups = "sdhi2_data8", "sdhi2_ctrl", "sdhi2_ds";
 604                 function = "sdhi2";
 605                 power-source = <3300>;
 606         };
 607
 608         sdhi2_pins_uhs: sd2_uhs {
 609                 groups = "sdhi2_data8", "sdhi2_ctrl", "sdhi2_ds";
 610                 function = "sdhi2";
 611                 power-source = <1800>;
 612         };
 613
 614         sdhi3_pins: sd3 {
 615                 groups = "sdhi3_data4", "sdhi3_ctrl";
 616                 function = "sdhi3";
 617                 power-source = <3300>;
 618         };
 619
 620         sdhi3_pins_uhs: sd3_uhs {
 621                 groups = "sdhi3_data4", "sdhi3_ctrl";
 622                 function = "sdhi3";
 623                 power-source = <1800>;
 624         };
 625
 626         sound_pins: sound {
 627                 groups = "ssi01239_ctrl", "ssi0_data", "ssi1_data_a";
 628                 function = "ssi";
 629         };
 630
 631         sound_clk_pins: sound_clk {
 632                 groups = "audio_clk_a_a", "audio_clk_b_a", "audio_clk_c_a",
 633                          "audio_clkout_a", "audio_clkout3_a";
 634                 function = "audio_clk";
 635         };
 636
 637         usb0_pins: usb0 {
 638                 groups = "usb0";
 639                 function = "usb0";
 640         };
 641
 642         usb1_pins: usb1 {
 643                 mux {
 644                         groups = "usb1";
 645                         function = "usb1";
 646                 };
 647
 648                 ovc {
 649                         pins = "GP_6_27";
 650                         bias-pull-up;
 651                 };
 652
 653                 pwen {
 654                         pins = "GP_6_26";
 655                         bias-pull-down;
 656                 };
 657         };
 658
 659         usb30_pins: usb30 {
 660                 groups = "usb30";
 661                 function = "usb30";
 662         };
 663 };
 664
 665 &pwm1 {
 666         pinctrl-0 = <&pwm1_pins>;
 667         pinctrl-names = "default";
 668
 669         status = "okay";
 670 };
 671
 672 &rcar_sound {
 673         pinctrl-0 = <&sound_pins &sound_clk_pins>;
 674         pinctrl-names = "default";
 675
 676         /* Single DAI */
 677         #sound-dai-cells = <0>;
 678
 679         /* audio_clkout0/1/2/3 */
 680         #clock-cells = <1>;
 681         clock-frequency = <12288000 11289600>;
 682
 683         status = "okay";
 684
 685         /* update <audio_clk_b> to <cs2000> */
 686         clocks = <&cpg CPG_MOD 1005>,
 687                  <&cpg CPG_MOD 1006>, <&cpg CPG_MOD 1007>,
 688                  <&cpg CPG_MOD 1008>, <&cpg CPG_MOD 1009>,
 689                  <&cpg CPG_MOD 1010>, <&cpg CPG_MOD 1011>,
 690                  <&cpg CPG_MOD 1012>, <&cpg CPG_MOD 1013>,
 691                  <&cpg CPG_MOD 1014>, <&cpg CPG_MOD 1015>,
 692                  <&cpg CPG_MOD 1022>, <&cpg CPG_MOD 1023>,
 693                  <&cpg CPG_MOD 1024>, <&cpg CPG_MOD 1025>,
 694                  <&cpg CPG_MOD 1026>, <&cpg CPG_MOD 1027>,
 695                  <&cpg CPG_MOD 1028>, <&cpg CPG_MOD 1029>,
 696                  <&cpg CPG_MOD 1030>, <&cpg CPG_MOD 1031>,
 697                  <&cpg CPG_MOD 1020>, <&cpg CPG_MOD 1021>,
 698                  <&cpg CPG_MOD 1020>, <&cpg CPG_MOD 1021>,
 699                  <&cpg CPG_MOD 1019>, <&cpg CPG_MOD 1018>,
 700                  <&audio_clk_a>, <&cs2000>,
 701                  <&audio_clk_c>,
 702                  <&cpg CPG_CORE CPG_AUDIO_CLK_I>;
 703
 704         ports {
 705                 rsnd_port0: port@0 {
 706                         rsnd_endpoint0: endpoint {
 707                                 remote-endpoint = <&ak4613_endpoint>;
 708
 709                                 dai-format = "left_j";
 710                                 bitclock-master = <&rsnd_endpoint0>;
 711                                 frame-master = <&rsnd_endpoint0>;
 712
 713                                 playback = <&ssi0 &src0 &dvc0>;
 714                                 capture  = <&ssi1 &src1 &dvc1>;
 715                         };
 716                 };
 717         };
 718 };
 719
 720 &scif1 {
 721         pinctrl-0 = <&scif1_pins>;
 722         pinctrl-names = "default";
 723
 724         uart-has-rtscts;
 725         /* Please only enable hscif1 or scif1 */
 726         /* status = "okay"; */
 727 };
 728
 729 &scif2 {
 730         pinctrl-0 = <&scif2_pins>;
 731         pinctrl-names = "default";
 732
 733         status = "okay";
 734 };
 735
 736 &scif_clk {
 737         clock-frequency = <14745600>;
 738 };
 739
 740 &sdhi0 {
 741         pinctrl-0 = <&sdhi0_pins>;
 742         pinctrl-1 = <&sdhi0_pins_uhs>;
 743         pinctrl-names = "default", "state_uhs";
 744
 745         vmmc-supply = <&vcc_sdhi0>;
 746         vqmmc-supply = <&vccq_sdhi0>;
 747         cd-gpios = <&gpio3 12 GPIO_ACTIVE_LOW>;
 748         wp-gpios = <&gpio3 13 GPIO_ACTIVE_HIGH>;
 749         bus-width = <4>;
 750         sd-uhs-sdr50;
 751         status = "okay";
 752 };
 753
 754 &sdhi2 {
 755         /* used for on-board 8bit eMMC */
 756         pinctrl-0 = <&sdhi2_pins>;
 757         pinctrl-1 = <&sdhi2_pins_uhs>;
 758         pinctrl-names = "default", "state_uhs";
 759
 760         vmmc-supply = <&reg_3p3v>;
 761         vqmmc-supply = <&reg_1p8v>;
 762         bus-width = <8>;
 763         mmc-hs200-1_8v;
 764         non-removable;
 765         fixed-emmc-driver-type = <1>;
 766         status = "okay";
 767 };
 768
 769 &sdhi3 {
 770         pinctrl-0 = <&sdhi3_pins>;
 771         pinctrl-1 = <&sdhi3_pins_uhs>;
 772         pinctrl-names = "default", "state_uhs";
 773
 774         vmmc-supply = <&vcc_sdhi3>;
 775         vqmmc-supply = <&vccq_sdhi3>;
 776         cd-gpios = <&gpio4 15 GPIO_ACTIVE_LOW>;
 777         wp-gpios = <&gpio4 16 GPIO_ACTIVE_HIGH>;
 778         bus-width = <4>;
 779         sd-uhs-sdr50;
 780         status = "okay";
 781 };
 782
 783 &ssi1 {
 784         shared-pin;
 785 };
 786
 787 &usb_extal_clk {
 788         clock-frequency = <50000000>;
 789 };
 790
 791 &usb2_phy0 {
 792         pinctrl-0 = <&usb0_pins>;
 793         pinctrl-names = "default";
 794
 795         vbus-supply = <&vbus0_usb2>;
 796         status = "okay";
 797 };
 798
 799 &usb2_phy1 {
 800         pinctrl-0 = <&usb1_pins>;
 801         pinctrl-names = "default";
 802
 803         status = "okay";
 804 };
 805
 806 &usb3_peri0 {
 807         phys = <&usb3_phy0>;
 808         phy-names = "usb";
 809
 810         status = "okay";
 811 };
 812
 813 &usb3_phy0 {
 814         status = "okay";
 815 };
 816
 817 &usb3s0_clk {
 818         clock-frequency = <100000000>;
 819 };
 820
 821 &vin0 {
 822         status = "okay";
 823 };
 824
 825 &vin1 {
 826         status = "okay";
 827 };
 828
 829 &vin2 {
 830         status = "okay";
 831 };
 832
 833 &vin3 {
 834         status = "okay";
 835 };
 836
 837 &vin4 {
 838         status = "okay";
 839 };
 840
 841 &vin5 {
 842         status = "okay";
 843 };
 844
 845 &vin6 {
 846         status = "okay";
 847 };
 848
 849 &vin7 {
 850         status = "okay";
 851 };
 852
 853 &rwdt {
 854         timeout-sec = <60>;
 855         status = "okay";
 856 };
 857
 858 &xhci0 {
 859         pinctrl-0 = <&usb30_pins>;
 860         pinctrl-names = "default";
 861
 862         status = "okay";
 863 };