arch/arm/dts/r8a7790-lager.dts

   1 // SPDX-License-Identifier: GPL-2.0
   2 /*
   3  * Device Tree Source for the Lager board
   4  *
   5  * Copyright (C) 2013-2014 Renesas Solutions Corp.
   6  * Copyright (C) 2014 Cogent Embedded, Inc.
   7  * Copyright (C) 2015-2016 Renesas Electronics Corporation
   8  */
   9
  10 /*
  11  * SSI-AK4643
  12  *
  13  * SW1: 1: AK4643
  14  *      2: CN22
  15  *      3: ADV7511
  16  *
  17  * This command is required when Playback/Capture
  18  *
  19  *      amixer set "LINEOUT Mixer DACL" on
  20  *      amixer set "DVC Out" 100%
  21  *      amixer set "DVC In" 100%
  22  *
  23  * You can use Mute
  24  *
  25  *      amixer set "DVC Out Mute" on
  26  *      amixer set "DVC In Mute" on
  27  *
  28  * You can use Volume Ramp
  29  *
  30  *      amixer set "DVC Out Ramp Up Rate"   "0.125 dB/64 steps"
  31  *      amixer set "DVC Out Ramp Down Rate" "0.125 dB/512 steps"
  32  *      amixer set "DVC Out Ramp" on
  33  *      aplay xxx.wav &
  34  *      amixer set "DVC Out"  80%  // Volume Down
  35  *      amixer set "DVC Out" 100%  // Volume Up
  36  */
  37
  38 /dts-v1/;
  39 #include "r8a7790.dtsi"
  40 #include <dt-bindings/gpio/gpio.h>
  41 #include <dt-bindings/input/input.h>
  42
  43 / {
  44         model = "Lager";
  45         compatible = "renesas,lager", "renesas,r8a7790";
  46
  47         aliases {
  48                 serial0 = &scif0;
  49                 serial1 = &scifa1;
  50                 i2c8 = &gpioi2c1;
  51                 i2c10 = &i2cexio0;
  52                 i2c11 = &i2cexio1;
  53         };
  54
  55         chosen {
  56                 bootargs = "ignore_loglevel rw root=/dev/nfs ip=dhcp";
  57                 stdout-path = "serial0:115200n8";
  58         };
  59
  60         memory@40000000 {
  61                 device_type = "memory";
  62                 reg = <0 0x40000000 0 0x40000000>;
  63         };
  64
  65         memory@140000000 {
  66                 device_type = "memory";
  67                 reg = <1 0x40000000 0 0xc0000000>;
  68         };
  69
  70         lbsc {
  71                 #address-cells = <1>;
  72                 #size-cells = <1>;
  73         };
  74
  75         keyboard {
  76                 compatible = "gpio-keys";
  77
  78                 one {
  79                         linux,code = <KEY_1>;
  80                         label = "SW2-1";
  81                         wakeup-source;
  82                         debounce-interval = <20>;
  83                         gpios = <&gpio1 14 GPIO_ACTIVE_LOW>;
  84                 };
  85                 two {
  86                         linux,code = <KEY_2>;
  87                         label = "SW2-2";
  88                         wakeup-source;
  89                         debounce-interval = <20>;
  90                         gpios = <&gpio1 24 GPIO_ACTIVE_LOW>;
  91                 };
  92                 three {
  93                         linux,code = <KEY_3>;
  94                         label = "SW2-3";
  95                         wakeup-source;
  96                         debounce-interval = <20>;
  97                         gpios = <&gpio1 26 GPIO_ACTIVE_LOW>;
  98                 };
  99                 four {
 100                         linux,code = <KEY_4>;
 101                         label = "SW2-4";
 102                         wakeup-source;
 103                         debounce-interval = <20>;
 104                         gpios = <&gpio1 28 GPIO_ACTIVE_LOW>;
 105                 };
 106         };
 107
 108         leds {
 109                 compatible = "gpio-leds";
 110                 led6 {
 111                         gpios = <&gpio4 22 GPIO_ACTIVE_HIGH>;
 112                 };
 113                 led7 {
 114                         gpios = <&gpio4 23 GPIO_ACTIVE_HIGH>;
 115                 };
 116                 led8 {
 117                         gpios = <&gpio5 17 GPIO_ACTIVE_HIGH>;
 118                 };
 119         };
 120
 121         fixedregulator3v3: regulator-3v3 {
 122                 compatible = "regulator-fixed";
 123                 regulator-name = "fixed-3.3V";
 124                 regulator-min-microvolt = <3300000>;
 125                 regulator-max-microvolt = <3300000>;
 126                 regulator-boot-on;
 127                 regulator-always-on;
 128         };
 129
 130         vcc_sdhi0: regulator-vcc-sdhi0 {
 131                 compatible = "regulator-fixed";
 132
 133                 regulator-name = "SDHI0 Vcc";
 134                 regulator-min-microvolt = <3300000>;
 135                 regulator-max-microvolt = <3300000>;
 136
 137                 gpio = <&gpio5 24 GPIO_ACTIVE_HIGH>;
 138                 enable-active-high;
 139         };
 140
 141         vccq_sdhi0: regulator-vccq-sdhi0 {
 142                 compatible = "regulator-gpio";
 143
 144                 regulator-name = "SDHI0 VccQ";
 145                 regulator-min-microvolt = <1800000>;
 146                 regulator-max-microvolt = <3300000>;
 147
 148                 gpios = <&gpio5 29 GPIO_ACTIVE_HIGH>;
 149                 gpios-states = <1>;
 150                 states = <3300000 1
 151                           1800000 0>;
 152         };
 153
 154         vcc_sdhi2: regulator-vcc-sdhi2 {
 155                 compatible = "regulator-fixed";
 156
 157                 regulator-name = "SDHI2 Vcc";
 158                 regulator-min-microvolt = <3300000>;
 159                 regulator-max-microvolt = <3300000>;
 160
 161                 gpio = <&gpio5 25 GPIO_ACTIVE_HIGH>;
 162                 enable-active-high;
 163         };
 164
 165         vccq_sdhi2: regulator-vccq-sdhi2 {
 166                 compatible = "regulator-gpio";
 167
 168                 regulator-name = "SDHI2 VccQ";
 169                 regulator-min-microvolt = <1800000>;
 170                 regulator-max-microvolt = <3300000>;
 171
 172                 gpios = <&gpio5 30 GPIO_ACTIVE_HIGH>;
 173                 gpios-states = <1>;
 174                 states = <3300000 1
 175                           1800000 0>;
 176         };
 177
 178         audio_clock: audio_clock {
 179                 compatible = "fixed-clock";
 180                 #clock-cells = <0>;
 181                 clock-frequency = <11289600>;
 182         };
 183
 184         rsnd_ak4643: sound {
 185                 compatible = "simple-audio-card";
 186
 187                 simple-audio-card,format = "left_j";
 188                 simple-audio-card,bitclock-master = <&sndcodec>;
 189                 simple-audio-card,frame-master = <&sndcodec>;
 190
 191                 sndcpu: simple-audio-card,cpu {
 192                         sound-dai = <&rcar_sound>;
 193                 };
 194
 195                 sndcodec: simple-audio-card,codec {
 196                         sound-dai = <&ak4643>;
 197                         clocks = <&audio_clock>;
 198                 };
 199         };
 200
 201         vga-encoder {
 202                 compatible = "adi,adv7123";
 203
 204                 ports {
 205                         #address-cells = <1>;
 206                         #size-cells = <0>;
 207
 208                         port@0 {
 209                                 reg = <0>;
 210                                 adv7123_in: endpoint {
 211                                         remote-endpoint = <&du_out_rgb>;
 212                                 };
 213                         };
 214                         port@1 {
 215                                 reg = <1>;
 216                                 adv7123_out: endpoint {
 217                                         remote-endpoint = <&vga_in>;
 218                                 };
 219                         };
 220                 };
 221         };
 222
 223         vga {
 224                 compatible = "vga-connector";
 225
 226                 port {
 227                         vga_in: endpoint {
 228                                 remote-endpoint = <&adv7123_out>;
 229                         };
 230                 };
 231         };
 232
 233         hdmi-in {
 234                 compatible = "hdmi-connector";
 235                 type = "a";
 236
 237                 port {
 238                         hdmi_con_in: endpoint {
 239                                 remote-endpoint = <&adv7612_in>;
 240                         };
 241                 };
 242         };
 243
 244         hdmi-out {
 245                 compatible = "hdmi-connector";
 246                 type = "a";
 247
 248                 port {
 249                         hdmi_con_out: endpoint {
 250                                 remote-endpoint = <&adv7511_out>;
 251                         };
 252                 };
 253         };
 254
 255         x2_clk: x2-clock {
 256                 compatible = "fixed-clock";
 257                 #clock-cells = <0>;
 258                 clock-frequency = <148500000>;
 259         };
 260
 261         x13_clk: x13-clock {
 262                 compatible = "fixed-clock";
 263                 #clock-cells = <0>;
 264                 clock-frequency = <148500000>;
 265         };
 266
 267         gpioi2c1: i2c-8 {
 268                 #address-cells = <1>;
 269                 #size-cells = <0>;
 270                 compatible = "i2c-gpio";
 271                 status = "disabled";
 272                 gpios = <&gpio1 17 GPIO_ACTIVE_HIGH /* sda */
 273                          &gpio1 16 GPIO_ACTIVE_HIGH /* scl */
 274                         >;
 275                 i2c-gpio,delay-us = <5>;
 276         };
 277
 278         /*
 279          * IIC0/I2C0 is routed to EXIO connector A, pins 114 (SCL) + 116 (SDA) only.
 280          * We use the I2C demuxer, so the desired IP core can be selected at runtime
 281          * depending on the use case (e.g. DMA with IIC0 or slave support with I2C0).
 282          * Note: For testing the I2C slave feature, it is convenient to connect this
 283          * bus with IIC3 on pins 110 (SCL) + 112 (SDA), select I2C0 at runtime, and
 284          * instantiate the slave device at runtime according to the documentation.
 285          * You can then communicate with the slave via IIC3.
 286          *
 287          * IIC0/I2C0 does not appear to support fallback to GPIO.
 288          */
 289         i2cexio0: i2c-10 {
 290                 compatible = "i2c-demux-pinctrl";
 291                 i2c-parent = <&iic0>, <&i2c0>;
 292                 i2c-bus-name = "i2c-exio0";
 293                 #address-cells = <1>;
 294                 #size-cells = <0>;
 295         };
 296
 297         /*
 298          * IIC1/I2C1 is routed to EXIO connector A, pins 78 (SCL) + 80 (SDA).
 299          * This is similar to the arangement described for i2cexio0 (above)
 300          * with a fallback to GPIO also provided.
 301          */
 302         i2cexio1: i2c-11 {
 303                 compatible = "i2c-demux-pinctrl";
 304                 i2c-parent = <&iic1>, <&i2c1>, <&gpioi2c1>;
 305                 i2c-bus-name = "i2c-exio1";
 306                 #address-cells = <1>;
 307                 #size-cells = <0>;
 308         };
 309 };
 310
 311 &du {
 312         pinctrl-0 = <&du_pins>;
 313         pinctrl-names = "default";
 314         status = "okay";
 315
 316         clocks = <&cpg CPG_MOD 724>, <&cpg CPG_MOD 723>, <&cpg CPG_MOD 722>,
 317                  <&cpg CPG_MOD 726>, <&cpg CPG_MOD 725>,
 318                  <&x13_clk>, <&x2_clk>;
 319         clock-names = "du.0", "du.1", "du.2", "lvds.0", "lvds.1",
 320                       "dclkin.0", "dclkin.1";
 321
 322         ports {
 323                 port@0 {
 324                         endpoint {
 325                                 remote-endpoint = <&adv7123_in>;
 326                         };
 327                 };
 328                 port@1 {
 329                         endpoint {
 330                                 remote-endpoint = <&adv7511_in>;
 331                         };
 332                 };
 333                 port@2 {
 334                         lvds_connector: endpoint {
 335                         };
 336                 };
 337         };
 338 };
 339
 340 &extal_clk {
 341         clock-frequency = <20000000>;
 342 };
 343
 344 &pfc {
 345         pinctrl-0 = <&scif_clk_pins>;
 346         pinctrl-names = "default";
 347
 348         du_pins: du {
 349                 groups = "du_rgb666", "du_sync_1", "du_clk_out_0";
 350                 function = "du";
 351         };
 352
 353         scif0_pins: scif0 {
 354                 groups = "scif0_data";
 355                 function = "scif0";
 356         };
 357
 358         scif_clk_pins: scif_clk {
 359                 groups = "scif_clk";
 360                 function = "scif_clk";
 361         };
 362
 363         ether_pins: ether {
 364                 groups = "eth_link", "eth_mdio", "eth_rmii";
 365                 function = "eth";
 366         };
 367
 368         phy1_pins: phy1 {
 369                 groups = "intc_irq0";
 370                 function = "intc";
 371         };
 372
 373         scifa1_pins: scifa1 {
 374                 groups = "scifa1_data";
 375                 function = "scifa1";
 376         };
 377
 378         sdhi0_pins: sd0 {
 379                 groups = "sdhi0_data4", "sdhi0_ctrl";
 380                 function = "sdhi0";
 381                 power-source = <3300>;
 382         };
 383
 384         sdhi0_pins_uhs: sd0_uhs {
 385                 groups = "sdhi0_data4", "sdhi0_ctrl";
 386                 function = "sdhi0";
 387                 power-source = <1800>;
 388         };
 389
 390         sdhi2_pins: sd2 {
 391                 groups = "sdhi2_data4", "sdhi2_ctrl";
 392                 function = "sdhi2";
 393                 power-source = <3300>;
 394         };
 395
 396         sdhi2_pins_uhs: sd2_uhs {
 397                 groups = "sdhi2_data4", "sdhi2_ctrl";
 398                 function = "sdhi2";
 399                 power-source = <1800>;
 400         };
 401
 402         mmc1_pins: mmc1 {
 403                 groups = "mmc1_data8", "mmc1_ctrl";
 404                 function = "mmc1";
 405         };
 406
 407         qspi_pins: qspi {
 408                 groups = "qspi_ctrl", "qspi_data4";
 409                 function = "qspi";
 410         };
 411
 412         msiof1_pins: msiof1 {
 413                 groups = "msiof1_clk", "msiof1_sync", "msiof1_rx",
 414                                  "msiof1_tx";
 415                 function = "msiof1";
 416         };
 417
 418         i2c0_pins: i2c0 {
 419                 groups = "i2c0";
 420                 function = "i2c0";
 421         };
 422
 423         iic0_pins: iic0 {
 424                 groups = "iic0";
 425                 function = "iic0";
 426         };
 427
 428         i2c1_pins: i2c1 {
 429                 groups = "i2c1";
 430                 function = "i2c1";
 431         };
 432
 433         iic1_pins: iic1 {
 434                 groups = "iic1";
 435                 function = "iic1";
 436         };
 437
 438         iic2_pins: iic2 {
 439                 groups = "iic2";
 440                 function = "iic2";
 441         };
 442
 443         iic3_pins: iic3 {
 444                 groups = "iic3";
 445                 function = "iic3";
 446         };
 447
 448         hsusb_pins: hsusb {
 449                 groups = "usb0_ovc_vbus";
 450                 function = "usb0";
 451         };
 452
 453         usb0_pins: usb0 {
 454                 groups = "usb0";
 455                 function = "usb0";
 456         };
 457
 458         usb1_pins: usb1 {
 459                 groups = "usb1";
 460                 function = "usb1";
 461         };
 462
 463         usb2_pins: usb2 {
 464                 groups = "usb2";
 465                 function = "usb2";
 466         };
 467
 468         vin0_pins: vin0 {
 469                 groups = "vin0_data24", "vin0_sync", "vin0_clkenb", "vin0_clk";
 470                 function = "vin0";
 471         };
 472
 473         vin1_pins: vin1 {
 474                 groups = "vin1_data8", "vin1_clk";
 475                 function = "vin1";
 476         };
 477
 478         sound_pins: sound {
 479                 groups = "ssi0129_ctrl", "ssi0_data", "ssi1_data";
 480                 function = "ssi";
 481         };
 482
 483         sound_clk_pins: sound_clk {
 484                 groups = "audio_clk_a";
 485                 function = "audio_clk";
 486         };
 487 };
 488
 489 &ether {
 490         pinctrl-0 = <&ether_pins &phy1_pins>;
 491         pinctrl-names = "default";
 492
 493         phy-handle = <&phy1>;
 494         renesas,ether-link-active-low;
 495         status = "okay";
 496
 497         phy1: ethernet-phy@1 {
 498                 reg = <1>;
 499                 interrupt-parent = <&irqc0>;
 500                 interrupts = <0 IRQ_TYPE_LEVEL_LOW>;
 501                 micrel,led-mode = <1>;
 502         };
 503 };
 504
 505 &cmt0 {
 506         status = "okay";
 507 };
 508
 509 &mmcif1 {
 510         pinctrl-0 = <&mmc1_pins>;
 511         pinctrl-names = "default";
 512
 513         vmmc-supply = <&fixedregulator3v3>;
 514         bus-width = <8>;
 515         non-removable;
 516         status = "okay";
 517 };
 518
 519 &sata1 {
 520         status = "okay";
 521 };
 522
 523 &qspi {
 524         pinctrl-0 = <&qspi_pins>;
 525         pinctrl-names = "default";
 526
 527         status = "okay";
 528
 529         flash: flash@0 {
 530                 compatible = "spansion,s25fl512s", "jedec,spi-nor";
 531                 reg = <0>;
 532                 spi-max-frequency = <30000000>;
 533                 spi-tx-bus-width = <4>;
 534                 spi-rx-bus-width = <4>;
 535                 spi-cpha;
 536                 spi-cpol;
 537                 m25p,fast-read;
 538
 539                 partitions {
 540                         compatible = "fixed-partitions";
 541                         #address-cells = <1>;
 542                         #size-cells = <1>;
 543
 544                         partition@0 {
 545                                 label = "loader";
 546                                 reg = <0x00000000 0x00040000>;
 547                                 read-only;
 548                         };
 549                         partition@40000 {
 550                                 label = "user";
 551                                 reg = <0x00040000 0x00400000>;
 552                                 read-only;
 553                         };
 554                         partition@440000 {
 555                                 label = "flash";
 556                                 reg = <0x00440000 0x03bc0000>;
 557                         };
 558                 };
 559         };
 560 };
 561
 562 &scif0 {
 563         pinctrl-0 = <&scif0_pins>;
 564         pinctrl-names = "default";
 565
 566         status = "okay";
 567 };
 568
 569 &scifa1 {
 570         pinctrl-0 = <&scifa1_pins>;
 571         pinctrl-names = "default";
 572
 573         status = "okay";
 574 };
 575
 576 &scif_clk {
 577         clock-frequency = <14745600>;
 578 };
 579
 580 &msiof1 {
 581         pinctrl-0 = <&msiof1_pins>;
 582         pinctrl-names = "default";
 583
 584         status = "okay";
 585
 586         pmic: pmic@0 {
 587                 compatible = "renesas,r2a11302ft";
 588                 reg = <0>;
 589                 spi-max-frequency = <6000000>;
 590                 spi-cpol;
 591                 spi-cpha;
 592         };
 593 };
 594
 595 &sdhi0 {
 596         pinctrl-0 = <&sdhi0_pins>;
 597         pinctrl-1 = <&sdhi0_pins_uhs>;
 598         pinctrl-names = "default", "state_uhs";
 599
 600         vmmc-supply = <&vcc_sdhi0>;
 601         vqmmc-supply = <&vccq_sdhi0>;
 602         cd-gpios = <&gpio3 6 GPIO_ACTIVE_LOW>;
 603         sd-uhs-sdr50;
 604         sd-uhs-sdr104;
 605         status = "okay";
 606 };
 607
 608 &sdhi2 {
 609         pinctrl-0 = <&sdhi2_pins>;
 610         pinctrl-1 = <&sdhi2_pins_uhs>;
 611         pinctrl-names = "default", "state_uhs";
 612
 613         vmmc-supply = <&vcc_sdhi2>;
 614         vqmmc-supply = <&vccq_sdhi2>;
 615         cd-gpios = <&gpio3 22 GPIO_ACTIVE_LOW>;
 616         sd-uhs-sdr50;
 617         status = "okay";
 618 };
 619
 620 &cpu0 {
 621         cpu0-supply = <&vdd_dvfs>;
 622 };
 623
 624 &i2c0   {
 625         pinctrl-0 = <&i2c0_pins>;
 626         pinctrl-names = "i2c-exio0";
 627 };
 628
 629 &iic0   {
 630         pinctrl-0 = <&iic0_pins>;
 631         pinctrl-names = "i2c-exio0";
 632 };
 633
 634 &i2c1   {
 635         pinctrl-0 = <&i2c1_pins>;
 636         pinctrl-names = "i2c-exio1";
 637 };
 638
 639 &iic1   {
 640         pinctrl-0 = <&iic1_pins>;
 641         pinctrl-names = "i2c-exio1";
 642 };
 643
 644 &iic2   {
 645         status = "okay";
 646         pinctrl-0 = <&iic2_pins>;
 647         pinctrl-names = "default";
 648
 649         clock-frequency = <100000>;
 650
 651         ak4643: codec@12 {
 652                 compatible = "asahi-kasei,ak4643";
 653                 #sound-dai-cells = <0>;
 654                 reg = <0x12>;
 655         };
 656
 657         composite-in@20 {
 658                 compatible = "adi,adv7180";
 659                 reg = <0x20>;
 660                 remote = <&vin1>;
 661
 662                 port {
 663                         adv7180: endpoint {
 664                                 bus-width = <8>;
 665                                 remote-endpoint = <&vin1ep0>;
 666                         };
 667                 };
 668         };
 669
 670         hdmi@39 {
 671                 compatible = "adi,adv7511w";
 672                 reg = <0x39>;
 673                 interrupt-parent = <&gpio1>;
 674                 interrupts = <15 IRQ_TYPE_LEVEL_LOW>;
 675
 676                 adi,input-depth = <8>;
 677                 adi,input-colorspace = "rgb";
 678                 adi,input-clock = "1x";
 679                 adi,input-style = <1>;
 680                 adi,input-justification = "evenly";
 681
 682                 ports {
 683                         #address-cells = <1>;
 684                         #size-cells = <0>;
 685
 686                         port@0 {
 687                                 reg = <0>;
 688                                 adv7511_in: endpoint {
 689                                         remote-endpoint = <&du_out_lvds0>;
 690                                 };
 691                         };
 692
 693                         port@1 {
 694                                 reg = <1>;
 695                                 adv7511_out: endpoint {
 696                                         remote-endpoint = <&hdmi_con_out>;
 697                                 };
 698                         };
 699                 };
 700         };
 701
 702         hdmi-in@4c {
 703                 compatible = "adi,adv7612";
 704                 reg = <0x4c>;
 705                 interrupt-parent = <&gpio1>;
 706                 interrupts = <20 IRQ_TYPE_LEVEL_LOW>;
 707                 default-input = <0>;
 708
 709                 ports {
 710                         #address-cells = <1>;
 711                         #size-cells = <0>;
 712
 713                         port@0 {
 714                                 reg = <0>;
 715                                 adv7612_in: endpoint {
 716                                         remote-endpoint = <&hdmi_con_in>;
 717                                 };
 718                         };
 719
 720                         port@2 {
 721                                 reg = <2>;
 722                                 adv7612_out: endpoint {
 723                                         remote-endpoint = <&vin0ep2>;
 724                                 };
 725                         };
 726                 };
 727         };
 728 };
 729
 730 &iic3 {
 731         pinctrl-names = "default";
 732         pinctrl-0 = <&iic3_pins>;
 733         status = "okay";
 734
 735         pmic@58 {
 736                 compatible = "dlg,da9063";
 737                 reg = <0x58>;
 738                 interrupt-parent = <&irqc0>;
 739                 interrupts = <2 IRQ_TYPE_LEVEL_LOW>;
 740                 interrupt-controller;
 741
 742                 rtc {
 743                         compatible = "dlg,da9063-rtc";
 744                 };
 745
 746                 wdt {
 747                         compatible = "dlg,da9063-watchdog";
 748                 };
 749         };
 750
 751         vdd_dvfs: regulator@68 {
 752                 compatible = "dlg,da9210";
 753                 reg = <0x68>;
 754                 interrupt-parent = <&irqc0>;
 755                 interrupts = <2 IRQ_TYPE_LEVEL_LOW>;
 756
 757                 regulator-min-microvolt = <1000000>;
 758                 regulator-max-microvolt = <1000000>;
 759                 regulator-boot-on;
 760                 regulator-always-on;
 761         };
 762 };
 763
 764 &pci0 {
 765         status = "okay";
 766         pinctrl-0 = <&usb0_pins>;
 767         pinctrl-names = "default";
 768 };
 769
 770 &pci1 {
 771         status = "okay";
 772         pinctrl-0 = <&usb1_pins>;
 773         pinctrl-names = "default";
 774 };
 775
 776 &xhci {
 777         status = "okay";
 778         pinctrl-0 = <&usb2_pins>;
 779         pinctrl-names = "default";
 780 };
 781
 782 &pci2 {
 783         status = "okay";
 784         pinctrl-0 = <&usb2_pins>;
 785         pinctrl-names = "default";
 786 };
 787
 788 &hsusb {
 789         status = "okay";
 790         pinctrl-0 = <&hsusb_pins>;
 791         pinctrl-names = "default";
 792         renesas,enable-gpio = <&gpio5 18 GPIO_ACTIVE_HIGH>;
 793 };
 794
 795 &usbphy {
 796         status = "okay";
 797 };
 798
 799 /* HDMI video input */
 800 &vin0 {
 801         pinctrl-0 = <&vin0_pins>;
 802         pinctrl-names = "default";
 803
 804         status = "okay";
 805
 806         port {
 807                 vin0ep2: endpoint {
 808                         remote-endpoint = <&adv7612_out>;
 809                         bus-width = <24>;
 810                         hsync-active = <0>;
 811                         vsync-active = <0>;
 812                         pclk-sample = <1>;
 813                         data-active = <1>;
 814                 };
 815         };
 816 };
 817
 818 /* composite video input */
 819 &vin1 {
 820         pinctrl-0 = <&vin1_pins>;
 821         pinctrl-names = "default";
 822
 823         status = "okay";
 824
 825         port {
 826                 #address-cells = <1>;
 827                 #size-cells = <0>;
 828
 829                 vin1ep0: endpoint {
 830                         remote-endpoint = <&adv7180>;
 831                         bus-width = <8>;
 832                 };
 833         };
 834 };
 835
 836 &rcar_sound {
 837         pinctrl-0 = <&sound_pins &sound_clk_pins>;
 838         pinctrl-names = "default";
 839
 840         /* Single DAI */
 841         #sound-dai-cells = <0>;
 842
 843         status = "okay";
 844
 845         rcar_sound,dai {
 846                 dai0 {
 847                         playback = <&ssi0 &src2 &dvc0>;
 848                         capture  = <&ssi1 &src3 &dvc1>;
 849                 };
 850         };
 851 };
 852
 853 &ssi1 {
 854         shared-pin;
 855 };