2 * This program is free software; you can redistribute it and/or modify
3 * it under the terms of the GNU General Public License version 2 as
4 * published by the Free Software Foundation.
7 #include <dt-bindings/input/input.h>
17 device_type = "memory";
22 compatible = "gpio-leds";
25 gpios = <&twl_gpio 18 GPIO_ACTIVE_LOW>; /* LEDA */
26 linux,default-trigger = "none";
30 wl12xx_vmmc: wl12xx_vmmc {
31 compatible = "regulator-fixed";
32 regulator-name = "vwl1271";
33 regulator-min-microvolt = <1800000>;
34 regulator-max-microvolt = <1800000>;
35 gpio = <&gpio5 29 0>; /* gpio157 */
36 startup-delay-us = <70000>;
38 vin-supply = <&vmmc2>;
43 ranges = <0 0 0x30000000 0x1000000>; /* CS0: 16MB for NAND */
46 compatible = "ti,omap2-nand";
47 reg = <0 0 4>; /* CS0, offset 0, IO size 4 */
48 interrupt-parent = <&gpmc>;
49 interrupts = <0 IRQ_TYPE_NONE>, /* fifoevent */
50 <1 IRQ_TYPE_NONE>; /* termcount */
51 linux,mtd-name = "micron,mt29f4g16abbda3w";
52 nand-bus-width = <16>;
53 ti,nand-ecc-opt = "bch8";
54 rb-gpios = <&gpmc 0 GPIO_ACTIVE_HIGH>; /* gpmc_wait0 */
55 gpmc,sync-clk-ps = <0>;
57 gpmc,cs-rd-off-ns = <44>;
58 gpmc,cs-wr-off-ns = <44>;
60 gpmc,adv-rd-off-ns = <34>;
61 gpmc,adv-wr-off-ns = <44>;
62 gpmc,we-off-ns = <40>;
63 gpmc,oe-off-ns = <54>;
64 gpmc,access-ns = <64>;
65 gpmc,rd-cycle-ns = <82>;
66 gpmc,wr-cycle-ns = <82>;
67 gpmc,wr-access-ns = <40>;
68 gpmc,wr-data-mux-bus-ns = <0>;
69 gpmc,device-width = <2>;
76 clock-frequency = <400000>;
80 interrupts = <7>; /* SYS_NIRQ cascaded to intc */
81 interrupt-parent = <&intc>;
83 compatible = "ti,twl4030-audio";
91 clock-frequency = <400000>;
95 clock-frequency = <400000>;
97 compatible = "at24,24c02";
104 * Only found on the wireless SOM. For the SOM without wireless, the pins for
105 * MMC3 can be routed with jumpers to the second MMC slot on the devkit and
106 * gpio157 is not connected. So this should be OK to keep common for now,
107 * probably device tree overlays is the way to go with the various SOM and
108 * jumpering combinations for the long run.
111 interrupts-extended = <&intc 94 &omap3_pmx_core2 0x46>;
112 pinctrl-0 = <&mmc3_pins &mmc3_core2_pins>;
113 pinctrl-names = "default";
114 vmmc-supply = <&wl12xx_vmmc>;
118 #address-cells = <1>;
121 compatible = "ti,wl1283";
123 interrupt-parent = <&gpio5>;
124 interrupts = <24 IRQ_TYPE_LEVEL_HIGH>; /* gpio 152 */
125 ref-clock-frequency = <26000000>;
126 tcxo-clock-frequency = <26000000>;
131 mmc3_pins: pinmux_mm3_pins {
132 pinctrl-single,pins = <
133 OMAP3_CORE1_IOPAD(0x2164, PIN_INPUT_PULLUP | MUX_MODE3) /* sdmmc2_dat4.sdmmc3_dat0 */
134 OMAP3_CORE1_IOPAD(0x2166, PIN_INPUT_PULLUP | MUX_MODE3) /* sdmmc2_dat5.sdmmc3_dat1 */
135 OMAP3_CORE1_IOPAD(0x2168, PIN_INPUT_PULLUP | MUX_MODE3) /* sdmmc2_dat6.sdmmc3_dat2 */
136 OMAP3_CORE1_IOPAD(0x216a, PIN_INPUT_PULLUP | MUX_MODE3) /* sdmmc2_dat6.sdmmc3_dat3 */
137 OMAP3_CORE1_IOPAD(0x2184, PIN_INPUT_PULLUP | MUX_MODE4) /* mcbsp4_clkx.gpio_152 */
138 OMAP3_CORE1_IOPAD(0x218e, PIN_OUTPUT | MUX_MODE4) /* mcbsp1_fsr.gpio_157 */
141 mcbsp2_pins: pinmux_mcbsp2_pins {
142 pinctrl-single,pins = <
143 OMAP3_CORE1_IOPAD(0x213c, PIN_INPUT | MUX_MODE0) /* mcbsp2_fsx */
144 OMAP3_CORE1_IOPAD(0x213e, PIN_INPUT | MUX_MODE0) /* mcbsp2_clkx */
145 OMAP3_CORE1_IOPAD(0x2140, PIN_INPUT | MUX_MODE0) /* mcbsp2_dr */
146 OMAP3_CORE1_IOPAD(0x2142, PIN_OUTPUT | MUX_MODE0) /* mcbsp2_dx */
149 uart2_pins: pinmux_uart2_pins {
150 pinctrl-single,pins = <
151 OMAP3_CORE1_IOPAD(0x2174, PIN_INPUT | MUX_MODE0) /* uart2_cts.uart2_cts */
152 OMAP3_CORE1_IOPAD(0x2176, PIN_OUTPUT | MUX_MODE0) /* uart2_rts .uart2_rts*/
153 OMAP3_CORE1_IOPAD(0x2178, PIN_OUTPUT | MUX_MODE0) /* uart2_tx.uart2_tx */
154 OMAP3_CORE1_IOPAD(0x217a, PIN_INPUT | MUX_MODE0) /* uart2_rx.uart2_rx */
155 OMAP3_CORE1_IOPAD(0x2198, PIN_OUTPUT | MUX_MODE4) /* GPIO_162,BT_EN */
158 mcspi1_pins: pinmux_mcspi1_pins {
159 pinctrl-single,pins = <
160 OMAP3_CORE1_IOPAD(0x21c8, PIN_INPUT | MUX_MODE0) /* mcspi1_clk.mcspi1_clk */
161 OMAP3_CORE1_IOPAD(0x21ca, PIN_OUTPUT | MUX_MODE0) /* mcspi1_simo.mcspi1_simo */
162 OMAP3_CORE1_IOPAD(0x21cc, PIN_INPUT_PULLUP | MUX_MODE0) /* mcspi1_somi.mcspi1_somi */
163 OMAP3_CORE1_IOPAD(0x21ce, PIN_OUTPUT | MUX_MODE0) /* mcspi1_cs0.mcspi1_cs0 */
166 hsusb_otg_pins: pinmux_hsusb_otg_pins {
167 pinctrl-single,pins = <
168 OMAP3_CORE1_IOPAD(0x21a2, PIN_INPUT | MUX_MODE0) /* hsusb0_clk.hsusb0_clk */
169 OMAP3_CORE1_IOPAD(0x21a4, PIN_OUTPUT | MUX_MODE0) /* hsusb0_stp.hsusb0_stp */
170 OMAP3_CORE1_IOPAD(0x21a6, PIN_INPUT | MUX_MODE0) /* hsusb0_dir.hsusb0_dir */
171 OMAP3_CORE1_IOPAD(0x21a8, PIN_INPUT | MUX_MODE0) /* hsusb0_nxt.hsusb0_nxt */
173 OMAP3_CORE1_IOPAD(0x21aa, PIN_INPUT | MUX_MODE0) /* hsusb0_data0.hsusb0_data0 */
174 OMAP3_CORE1_IOPAD(0x21ac, PIN_INPUT | MUX_MODE0) /* hsusb0_data1.hsusb0_data1 */
175 OMAP3_CORE1_IOPAD(0x21ae, PIN_INPUT | MUX_MODE0) /* hsusb0_data2.hsusb0_data2 */
176 OMAP3_CORE1_IOPAD(0x21b0, PIN_INPUT | MUX_MODE0) /* hsusb0_data3.hsusb0_data3 */
177 OMAP3_CORE1_IOPAD(0x21b2, PIN_INPUT | MUX_MODE0) /* hsusb0_data4.hsusb0_data4 */
178 OMAP3_CORE1_IOPAD(0x21b4, PIN_INPUT | MUX_MODE0) /* hsusb0_data5.hsusb0_data5 */
179 OMAP3_CORE1_IOPAD(0x21b6, PIN_INPUT | MUX_MODE0) /* hsusb0_data6.hsusb0_data6 */
180 OMAP3_CORE1_IOPAD(0x21b8, PIN_INPUT | MUX_MODE0) /* hsusb0_data7.hsusb0_data7 */
186 interrupts-extended = <&intc 73 &omap3_pmx_core OMAP3_UART2_RX>;
187 pinctrl-names = "default";
188 pinctrl-0 = <&uart2_pins>;
192 pinctrl-names = "default";
193 pinctrl-0 = <&mcspi1_pins>;
197 mmc3_core2_pins: pinmux_mmc3_core2_pins {
198 pinctrl-single,pins = <
199 OMAP3630_CORE2_IOPAD(0x25d8, PIN_INPUT_PULLUP | MUX_MODE2) /* etk_clk.sdmmc3_clk */
200 OMAP3630_CORE2_IOPAD(0x25da, PIN_INPUT_PULLUP | MUX_MODE2) /* etk_ctl.sdmmc3_cmd */
205 #include "twl4030.dtsi"
206 #include "twl4030_omap3.dtsi"
210 compatible = "ti,twl4030-power-idle-osc-off", "ti,twl4030-power-idle";