arch/arm/dts/am335x-regor.dtsi

   1 // SPDX-License-Identifier: GPL-2.0
   2 /*
   3  * Copyright (C) 2019 Phytec Messtechnik GmbH
   4  * Author: Teresa Remmet <t.remmet@phytec.de>
   5  *
   6  */
   7
   8 / {
   9         model = "Phytec AM335x phyBOARD-REGOR";
  10         compatible = "phytec,am335x-regor", "phytec,am335x-phycore-som", "ti,am33xx";
  11
  12         vcc3v3: fixedregulator@1 {
  13                 compatible = "regulator-fixed";
  14                 regulator-name = "vcc3v3";
  15                 regulator-min-microvolt = <3300000>;
  16                 regulator-max-microvolt = <3300000>;
  17                 regulator-boot-on;
  18         };
  19
  20         /* User IO */
  21         user_leds: user_leds {
  22                 compatible = "gpio-leds";
  23                 pinctrl-names = "default";
  24                 pinctrl-0 = <&user_leds_pins>;
  25
  26                 run_stop-led {
  27                         gpios = <&gpio2 22 GPIO_ACTIVE_HIGH>;
  28                         linux,default-trigger = "gpio";
  29                         default-state = "off";
  30                 };
  31
  32                 error-led {
  33                         gpios = <&gpio3 15 GPIO_ACTIVE_HIGH>;
  34                         linux,default-trigger = "gpio";
  35                         default-state = "off";
  36                 };
  37         };
  38 };
  39
  40 /* User Leds */
  41 &am33xx_pinmux {
  42         user_leds_pins: pinmux_user_leds {
  43                 pinctrl-single,pins = <
  44                         AM33XX_IOPAD(0x8E0, PIN_OUTPUT_PULLDOWN | MUX_MODE7)    /* lcd_hsync.gpio2_22 */
  45                         AM33XX_IOPAD(0x994, PIN_OUTPUT_PULLDOWN | MUX_MODE7)    /* mcasp0_fsx.gpio3_15 */
  46                 >;
  47         };
  48 };
  49
  50 /* CAN Busses */
  51 &am33xx_pinmux {
  52         dcan1_pins: pinmux_dcan1 {
  53                 pinctrl-single,pins = <
  54                         AM33XX_IOPAD(0x968, PIN_OUTPUT_PULLUP | MUX_MODE2)      /* uart0_ctsn.d_can1_tx */
  55                         AM33XX_IOPAD(0x96C, PIN_INPUT_PULLUP | MUX_MODE2)       /* uart0_rtsn.d_can1_rx */
  56                 >;
  57         };
  58 };
  59
  60 &dcan1 {
  61         pinctrl-names = "default";
  62         pinctrl-0 = <&dcan1_pins>;
  63         status = "okay";
  64 };
  65
  66 /* Ethernet */
  67 &am33xx_pinmux {
  68         ethernet1_pins: pinmux_ethernet1 {
  69                 pinctrl-single,pins = <
  70                         AM33XX_IOPAD(0x840, PIN_OUTPUT | MUX_MODE1)             /* gpmc_a0.mii2_txen */
  71                         AM33XX_IOPAD(0x844, PIN_INPUT_PULLDOWN | MUX_MODE1)     /* gpmc_a1.mii2_rxdv */
  72                         AM33XX_IOPAD(0x848, PIN_OUTPUT | MUX_MODE1)             /* gpmc_a2.mii2_txd3 */
  73                         AM33XX_IOPAD(0x84C, PIN_OUTPUT | MUX_MODE1)             /* gpmc_a3.mii2_txd2 */
  74                         AM33XX_IOPAD(0x850, PIN_OUTPUT | MUX_MODE1)             /* gpmc_a4.mii2_txd1 */
  75                         AM33XX_IOPAD(0x854, PIN_OUTPUT | MUX_MODE1)             /* gpmc_a5.mii2_txd0 */
  76                         AM33XX_IOPAD(0x858, PIN_INPUT_PULLDOWN | MUX_MODE1)     /* gpmc_a6.mii2_txclk */
  77                         AM33XX_IOPAD(0x85C, PIN_INPUT_PULLDOWN | MUX_MODE1)     /* gpmc_a7.mii2_rxclk */
  78                         AM33XX_IOPAD(0x860, PIN_INPUT_PULLDOWN | MUX_MODE1)     /* gpmc_a8.mii2_rxd3 */
  79                         AM33XX_IOPAD(0x864, PIN_INPUT_PULLDOWN | MUX_MODE1)      /* gpmc_a9.mii2_rxd2 */
  80                         AM33XX_IOPAD(0x868, PIN_INPUT_PULLDOWN | MUX_MODE1)     /* gpmc_a10.mii2_rxd1 */
  81                         AM33XX_IOPAD(0x86C, PIN_INPUT_PULLDOWN | MUX_MODE1)     /* gpmc_a11.mii2_rxd0 */
  82                         AM33XX_IOPAD(0x874, PIN_INPUT_PULLDOWN | MUX_MODE1)     /* gpmc_wpn.mii2_rxerr */
  83                         AM33XX_IOPAD(0x878, PIN_INPUT_PULLDOWN | MUX_MODE1)     /* gpmc_ben1.mii2_col */
  84                 >;
  85         };
  86 };
  87
  88 &cpsw_emac1 {
  89         phy-handle = <&phy1>;
  90         phy-mode = "mii";
  91         dual_emac_res_vlan = <2>;
  92 };
  93
  94 &davinci_mdio {
  95         phy1: ethernet-phy@1 {
  96                 reg = <1>;
  97         };
  98 };
  99
 100 &mac {
 101         slaves = <2>;
 102         pinctrl-names = "default";
 103         pinctrl-0 = <&ethernet0_pins &ethernet1_pins>;
 104         dual_emac = <1>;
 105 };
 106
 107 /* GPIOs */
 108 &am33xx_pinmux {
 109         pinctrl-names = "default";
 110         pinctrl-0 = <&user_gpios_pins>;
 111
 112         user_gpios_pins: pinmux_user_gpios {
 113                 pinctrl-single,pins = <
 114                         /* DIGIN 1-4 */
 115                         AM33XX_IOPAD(0x82C, PIN_INPUT | MUX_MODE7)              /* gpmc_ad11.gpio0_27 */
 116                         AM33XX_IOPAD(0x828, PIN_INPUT | MUX_MODE7)              /* gpmc_ad10.gpio0_26 */
 117                         AM33XX_IOPAD(0x824, PIN_INPUT | MUX_MODE7)              /* gpmc_ad9.gpio0_23 */
 118                         AM33XX_IOPAD(0x820, PIN_INPUT | MUX_MODE7)              /* gpmc_ad8.gpio0_22 */
 119                         /* DIGOUT 1-4 */
 120                         AM33XX_IOPAD(0x83C, PIN_OUTPUT | MUX_MODE7)             /* gpmc_ad15.gpio1_15 */
 121                         AM33XX_IOPAD(0x838, PIN_OUTPUT | MUX_MODE7)             /* gpmc_ad14.gpio1_14 */
 122                         AM33XX_IOPAD(0x834, PIN_OUTPUT | MUX_MODE7)             /* gpmc_ad13.gpio1_13 */
 123                         AM33XX_IOPAD(0x830, PIN_OUTPUT | MUX_MODE7)             /* gpmc_ad12.gpio1_12 */
 124                 >;
 125         };
 126 };
 127
 128 /* MMC */
 129 &am33xx_pinmux {
 130         mmc1_pins: pinmux_mmc1 {
 131                 pinctrl-single,pins = <
 132                         AM33XX_IOPAD(0x8F0, PIN_INPUT_PULLUP | MUX_MODE0)
 133                         AM33XX_IOPAD(0x8F4, PIN_INPUT_PULLUP | MUX_MODE0)
 134                         AM33XX_IOPAD(0x8F8, PIN_INPUT_PULLUP | MUX_MODE0)
 135                         AM33XX_IOPAD(0x8FC, PIN_INPUT_PULLUP | MUX_MODE0)
 136                         AM33XX_IOPAD(0x900, PIN_INPUT_PULLUP | MUX_MODE0)
 137                         AM33XX_IOPAD(0x904, PIN_INPUT_PULLUP | MUX_MODE0)
 138                         AM33XX_IOPAD(0x960, PIN_INPUT_PULLUP | MUX_MODE7)       /* spi0_cs1.mmc0_sdcd */
 139                 >;
 140         };
 141 };
 142
 143 &mmc1 {
 144         vmmc-supply = <&vcc3v3>;
 145         bus-width = <4>;
 146         pinctrl-names = "default";
 147         pinctrl-0 = <&mmc1_pins>;
 148         cd-gpios = <&gpio0 6 GPIO_ACTIVE_LOW>;
 149         status = "okay";
 150 };
 151
 152 /* RTC */
 153 &i2c_rtc {
 154         status = "okay";
 155 };
 156
 157 /* UARTs */
 158 &am33xx_pinmux {
 159         uart0_pins: pinmux_uart0 {
 160                 pinctrl-single,pins = <
 161                         AM33XX_IOPAD(0x970, PIN_INPUT_PULLUP | MUX_MODE0)
 162                         AM33XX_IOPAD(0x974, PIN_OUTPUT_PULLDOWN | MUX_MODE0)
 163                 >;
 164         };
 165
 166         uart2_pins: pinmux_uart2 {
 167                 pinctrl-single,pins = <
 168                         AM33XX_IOPAD(0x92C, PIN_INPUT_PULLUP | MUX_MODE1)       /* mii1_tx_clk.uart2_rxd */
 169                         AM33XX_IOPAD(0x930, PIN_OUTPUT_PULLDOWN | MUX_MODE1)    /* mii1_rx_clk.uart2_txd */
 170                 >;
 171         };
 172 };
 173
 174 &uart0 {
 175         pinctrl-names = "default";
 176         pinctrl-0 = <&uart0_pins>;
 177         status = "okay";
 178 };
 179
 180 &uart2 {
 181         pinctrl-names = "default";
 182         pinctrl-0 = <&uart2_pins>;
 183         status = "okay";
 184 };
 185
 186 /* RS485 - UART1 */
 187 &am33xx_pinmux {
 188         uart1_rs485_pins: pinmux_uart1_rs485_pins {
 189                 pinctrl-single,pins = <
 190                         AM33XX_IOPAD(0x980, PIN_INPUT_PULLUP | MUX_MODE0)
 191                         AM33XX_IOPAD(0x984, PIN_OUTPUT_PULLDOWN | MUX_MODE0)
 192                         AM33XX_IOPAD(0x97C, PIN_OUTPUT_PULLUP | MUX_MODE0)
 193                 >;
 194         };
 195 };
 196
 197 &uart1 {
 198         pinctrl-names = "default";
 199         pinctrl-0 = <&uart1_rs485_pins>;
 200         status = "okay";
 201         linux,rs485-enabled-at-boot-time;
 202 };