1 // SPDX-License-Identifier: GPL-2.0+
3 * Copyright (C) 2018 B&R Industrial Automation GmbH
4 * http://www.br-automation.com
12 model = "BRPPT1 (MMC) Panel";
13 compatible = "ti,am33xx";
15 fset: factory-settings {
16 bl-version = "ABCDEFGHIJKLMNOPQRSTUVWXYZ0123456890";
18 order-no = "6PPT30 (MMC)";
19 hw-revision = "ABCDEFGHIJKLMNOPQRSTUVWXYZ0123456890";
27 ds1bkl0 = &pwmbacklight;
37 bootargs = "console=ttyO0,115200 earlyprintk";
42 device_type = "memory";
43 reg = <0x80000000 0x10000000>; /* 256 MB */
49 compatible = "ti,tilcdc,panel";
50 enable-gpios = <&gpio0 6 GPIO_ACTIVE_LOW>;
52 backlight = <&pwmbacklight>;
53 bkl-pwm = <&pwmbacklight>;
69 native-mode = <&timing0>;
71 clock-frequency = <32000000>;
88 vmmcsd_fixed: fixedregulator@0 {
89 compatible = "regulator-fixed";
90 regulator-name = "vmmcsd_fixed";
91 regulator-min-microvolt = <3300000>;
92 regulator-max-microvolt = <3300000>;
95 pwm0: omap-pwm@timer5 {
96 compatible = "ti,omap-dmtimer-pwm";
97 ti,timers = <&timer5>;
101 pwm1: omap-pwm@timer6 {
102 compatible = "ti,omap-dmtimer-pwm";
103 ti,timers = <&timer6>;
108 compatible = "pwm-beeper";
109 pwms = <&pwm0 0 0 0>;
112 pwmbacklight: pwm-bkl {
113 compatible = "pwm-backlight";
114 pwms = <&pwm1 0 5000000 0>;
116 default-brightness-level = <255>;
117 brightness-levels = <0 16 32 64 128 170 202 234 255>;
119 power-supply = <&vmmcsd_fixed>;
120 enable-gpios = <&gpio0 7 GPIO_ACTIVE_HIGH>;
124 &uart0 { /* console uart */
136 clock-frequency = <400000>;
138 tps: tps@24 { /* PMIC controller */
141 compatible = "ti,tps65217";
144 compatible = "ti,tps65217-bl";
145 isel = <1>; /* 1 - ISET1, 2 ISET2 */
146 fdim = <1000>; /* TPS65217_BL_FDIM_1kHZ */
147 default-brightness = <50>;
154 clock-frequency = <100000>;
194 phy0: ethernet-phy@0 {
198 phy1: ethernet-phy@1 {
208 phy-handle = <&phy0>;
209 dual_emac_res_vlan = <1>;
214 phy-handle = <&phy1>;
215 dual_emac_res_vlan = <2>;
221 vmmc-supply = <&vmmcsd_fixed>;
224 ti,needs-special-hs-handling;
225 ti,vcc-aux-disable-is-sleep;
231 vmmc-supply = <&vmmcsd_fixed>;
234 ti,needs-special-hs-handling;
235 ti,vcc-aux-disable-is-sleep;
295 ti,x-plate-resistance = <200>;
296 ti,zx-cutoff-ratio = <40>;
297 ti,min_deviation = <60>;
298 ti,max_deviation = <600>;
299 ti,coordinate-readouts = <5>;
300 ti,wire-config = <0x00 0x11 0x22 0x33>;
308 ti,adc-channels = <5 6 7>;
312 &timer6 { /* used for cpsw end device */
318 &timer7 { /* used for cpsw end device */