arch/arm/boot/dts/qcom-ipq8064.dtsi

   1 // SPDX-License-Identifier: GPL-2.0
   2 /dts-v1/;
   3
   4 #include <dt-bindings/interrupt-controller/arm-gic.h>
   5 #include <dt-bindings/mfd/qcom-rpm.h>
   6 #include <dt-bindings/clock/qcom,rpmcc.h>
   7 #include <dt-bindings/clock/qcom,gcc-ipq806x.h>
   8 #include <dt-bindings/clock/qcom,lcc-ipq806x.h>
   9 #include <dt-bindings/gpio/gpio.h>
  10 #include <dt-bindings/reset/qcom,gcc-ipq806x.h>
  11 #include <dt-bindings/soc/qcom,gsbi.h>
  12 #include <dt-bindings/interrupt-controller/arm-gic.h>
  13
  14 / {
  15         #address-cells = <1>;
  16         #size-cells = <1>;
  17         model = "Qualcomm IPQ8064";
  18         compatible = "qcom,ipq8064";
  19         interrupt-parent = <&intc>;
  20
  21         cpus {
  22                 #address-cells = <1>;
  23                 #size-cells = <0>;
  24
  25                 cpu0: cpu@0 {
  26                         compatible = "qcom,krait";
  27                         enable-method = "qcom,kpss-acc-v1";
  28                         device_type = "cpu";
  29                         reg = <0>;
  30                         next-level-cache = <&L2>;
  31                         qcom,acc = <&acc0>;
  32                         qcom,saw = <&saw0>;
  33                 };
  34
  35                 cpu1: cpu@1 {
  36                         compatible = "qcom,krait";
  37                         enable-method = "qcom,kpss-acc-v1";
  38                         device_type = "cpu";
  39                         reg = <1>;
  40                         next-level-cache = <&L2>;
  41                         qcom,acc = <&acc1>;
  42                         qcom,saw = <&saw1>;
  43                 };
  44
  45                 L2: l2-cache {
  46                         compatible = "cache";
  47                         cache-level = <2>;
  48                 };
  49         };
  50
  51         thermal-zones {
  52                 sensor0-thermal {
  53                         polling-delay-passive = <0>;
  54                         polling-delay = <0>;
  55                         thermal-sensors = <&tsens 0>;
  56
  57                         trips {
  58                                 cpu-critical {
  59                                         temperature = <105000>;
  60                                         hysteresis = <2000>;
  61                                         type = "critical";
  62                                 };
  63
  64                                 cpu-hot {
  65                                         temperature = <95000>;
  66                                         hysteresis = <2000>;
  67                                         type = "hot";
  68                                 };
  69                         };
  70                 };
  71
  72                 sensor1-thermal {
  73                         polling-delay-passive = <0>;
  74                         polling-delay = <0>;
  75                         thermal-sensors = <&tsens 1>;
  76
  77                         trips {
  78                                 cpu-critical {
  79                                         temperature = <105000>;
  80                                         hysteresis = <2000>;
  81                                         type = "critical";
  82                                 };
  83
  84                                 cpu-hot {
  85                                         temperature = <95000>;
  86                                         hysteresis = <2000>;
  87                                         type = "hot";
  88                                 };
  89                         };
  90                 };
  91
  92                 sensor2-thermal {
  93                         polling-delay-passive = <0>;
  94                         polling-delay = <0>;
  95                         thermal-sensors = <&tsens 2>;
  96
  97                         trips {
  98                                 cpu-critical {
  99                                         temperature = <105000>;
 100                                         hysteresis = <2000>;
 101                                         type = "critical";
 102                                 };
 103
 104                                 cpu-hot {
 105                                         temperature = <95000>;
 106                                         hysteresis = <2000>;
 107                                         type = "hot";
 108                                 };
 109                         };
 110                 };
 111
 112                 sensor3-thermal {
 113                         polling-delay-passive = <0>;
 114                         polling-delay = <0>;
 115                         thermal-sensors = <&tsens 3>;
 116
 117                         trips {
 118                                 cpu-critical {
 119                                         temperature = <105000>;
 120                                         hysteresis = <2000>;
 121                                         type = "critical";
 122                                 };
 123
 124                                 cpu-hot {
 125                                         temperature = <95000>;
 126                                         hysteresis = <2000>;
 127                                         type = "hot";
 128                                 };
 129                         };
 130                 };
 131
 132                 sensor4-thermal {
 133                         polling-delay-passive = <0>;
 134                         polling-delay = <0>;
 135                         thermal-sensors = <&tsens 4>;
 136
 137                         trips {
 138                                 cpu-critical {
 139                                         temperature = <105000>;
 140                                         hysteresis = <2000>;
 141                                         type = "critical";
 142                                 };
 143
 144                                 cpu-hot {
 145                                         temperature = <95000>;
 146                                         hysteresis = <2000>;
 147                                         type = "hot";
 148                                 };
 149                         };
 150                 };
 151
 152                 sensor5-thermal {
 153                         polling-delay-passive = <0>;
 154                         polling-delay = <0>;
 155                         thermal-sensors = <&tsens 5>;
 156
 157                         trips {
 158                                 cpu-critical {
 159                                         temperature = <105000>;
 160                                         hysteresis = <2000>;
 161                                         type = "critical";
 162                                 };
 163
 164                                 cpu-hot {
 165                                         temperature = <95000>;
 166                                         hysteresis = <2000>;
 167                                         type = "hot";
 168                                 };
 169                         };
 170                 };
 171
 172                 sensor6-thermal {
 173                         polling-delay-passive = <0>;
 174                         polling-delay = <0>;
 175                         thermal-sensors = <&tsens 6>;
 176
 177                         trips {
 178                                 cpu-critical {
 179                                         temperature = <105000>;
 180                                         hysteresis = <2000>;
 181                                         type = "critical";
 182                                 };
 183
 184                                 cpu-hot {
 185                                         temperature = <95000>;
 186                                         hysteresis = <2000>;
 187                                         type = "hot";
 188                                 };
 189                         };
 190                 };
 191
 192                 sensor7-thermal {
 193                         polling-delay-passive = <0>;
 194                         polling-delay = <0>;
 195                         thermal-sensors = <&tsens 7>;
 196
 197                         trips {
 198                                 cpu-critical {
 199                                         temperature = <105000>;
 200                                         hysteresis = <2000>;
 201                                         type = "critical";
 202                                 };
 203
 204                                 cpu-hot {
 205                                         temperature = <95000>;
 206                                         hysteresis = <2000>;
 207                                         type = "hot";
 208                                 };
 209                         };
 210                 };
 211
 212                 sensor8-thermal {
 213                         polling-delay-passive = <0>;
 214                         polling-delay = <0>;
 215                         thermal-sensors = <&tsens 8>;
 216
 217                         trips {
 218                                 cpu-critical {
 219                                         temperature = <105000>;
 220                                         hysteresis = <2000>;
 221                                         type = "critical";
 222                                 };
 223
 224                                 cpu-hot {
 225                                         temperature = <95000>;
 226                                         hysteresis = <2000>;
 227                                         type = "hot";
 228                                 };
 229                         };
 230                 };
 231
 232                 sensor9-thermal {
 233                         polling-delay-passive = <0>;
 234                         polling-delay = <0>;
 235                         thermal-sensors = <&tsens 9>;
 236
 237                         trips {
 238                                 cpu-critical {
 239                                         temperature = <105000>;
 240                                         hysteresis = <2000>;
 241                                         type = "critical";
 242                                 };
 243
 244                                 cpu-hot {
 245                                         temperature = <95000>;
 246                                         hysteresis = <2000>;
 247                                         type = "hot";
 248                                 };
 249                         };
 250                 };
 251
 252                 sensor10-thermal {
 253                         polling-delay-passive = <0>;
 254                         polling-delay = <0>;
 255                         thermal-sensors = <&tsens 10>;
 256
 257                         trips {
 258                                 cpu-critical {
 259                                         temperature = <105000>;
 260                                         hysteresis = <2000>;
 261                                         type = "critical";
 262                                 };
 263
 264                                 cpu-hot {
 265                                         temperature = <95000>;
 266                                         hysteresis = <2000>;
 267                                         type = "hot";
 268                                 };
 269                         };
 270                 };
 271         };
 272
 273         memory {
 274                 device_type = "memory";
 275                 reg = <0x0 0x0>;
 276         };
 277
 278         cpu-pmu {
 279                 compatible = "qcom,krait-pmu";
 280                 interrupts = <GIC_PPI 10 (GIC_CPU_MASK_SIMPLE(2) |
 281                                           IRQ_TYPE_LEVEL_HIGH)>;
 282         };
 283
 284         reserved-memory {
 285                 #address-cells = <1>;
 286                 #size-cells = <1>;
 287                 ranges;
 288
 289                 nss@40000000 {
 290                         reg = <0x40000000 0x1000000>;
 291                         no-map;
 292                 };
 293
 294                 smem: smem@41000000 {
 295                         reg = <0x41000000 0x200000>;
 296                         no-map;
 297                 };
 298         };
 299
 300         clocks {
 301                 cxo_board {
 302                         compatible = "fixed-clock";
 303                         #clock-cells = <0>;
 304                         clock-frequency = <25000000>;
 305                 };
 306
 307                 pxo_board {
 308                         compatible = "fixed-clock";
 309                         #clock-cells = <0>;
 310                         clock-frequency = <25000000>;
 311                 };
 312
 313                 sleep_clk: sleep_clk {
 314                         compatible = "fixed-clock";
 315                         clock-frequency = <32768>;
 316                         #clock-cells = <0>;
 317                 };
 318         };
 319
 320         firmware {
 321                 scm {
 322                         compatible = "qcom,scm-ipq806x", "qcom,scm";
 323                 };
 324         };
 325
 326         soc: soc {
 327                 #address-cells = <1>;
 328                 #size-cells = <1>;
 329                 ranges;
 330                 compatible = "simple-bus";
 331
 332                 lpass@28100000 {
 333                         compatible = "qcom,lpass-cpu";
 334                         status = "disabled";
 335                         clocks = <&lcc AHBIX_CLK>,
 336                                         <&lcc MI2S_OSR_CLK>,
 337                                         <&lcc MI2S_BIT_CLK>;
 338                         clock-names = "ahbix-clk",
 339                                         "mi2s-osr-clk",
 340                                         "mi2s-bit-clk";
 341                         interrupts = <GIC_SPI 85 IRQ_TYPE_EDGE_RISING>;
 342                         interrupt-names = "lpass-irq-lpaif";
 343                         reg = <0x28100000 0x10000>;
 344                         reg-names = "lpass-lpaif";
 345                 };
 346
 347                 qcom_pinmux: pinmux@800000 {
 348                         compatible = "qcom,ipq8064-pinctrl";
 349                         reg = <0x800000 0x4000>;
 350
 351                         gpio-controller;
 352                         gpio-ranges = <&qcom_pinmux 0 0 69>;
 353                         #gpio-cells = <2>;
 354                         interrupt-controller;
 355                         #interrupt-cells = <2>;
 356                         interrupts = <GIC_SPI 16 IRQ_TYPE_LEVEL_HIGH>;
 357
 358                         pcie0_pins: pcie0_pinmux {
 359                                 mux {
 360                                         pins = "gpio3";
 361                                         function = "pcie1_rst";
 362                                         drive-strength = <12>;
 363                                         bias-disable;
 364                                 };
 365                         };
 366
 367                         pcie1_pins: pcie1_pinmux {
 368                                 mux {
 369                                         pins = "gpio48";
 370                                         function = "pcie2_rst";
 371                                         drive-strength = <12>;
 372                                         bias-disable;
 373                                 };
 374                         };
 375
 376                         pcie2_pins: pcie2_pinmux {
 377                                 mux {
 378                                         pins = "gpio63";
 379                                         function = "pcie3_rst";
 380                                         drive-strength = <12>;
 381                                         bias-disable;
 382                                 };
 383                         };
 384
 385                         spi_pins: spi_pins {
 386                                 mux {
 387                                         pins = "gpio18", "gpio19", "gpio21";
 388                                         function = "gsbi5";
 389                                         drive-strength = <10>;
 390                                         bias-none;
 391                                 };
 392                         };
 393
 394                         leds_pins: leds_pins {
 395                                 mux {
 396                                         pins = "gpio7", "gpio8", "gpio9",
 397                                                "gpio26", "gpio53";
 398                                         function = "gpio";
 399                                         drive-strength = <2>;
 400                                         bias-pull-down;
 401                                         output-low;
 402                                 };
 403                         };
 404
 405                         buttons_pins: buttons_pins {
 406                                 mux {
 407                                         pins = "gpio54";
 408                                         drive-strength = <2>;
 409                                         bias-pull-up;
 410                                 };
 411                         };
 412
 413                         nand_pins: nand_pins {
 414                                 mux {
 415                                         pins = "gpio34", "gpio35", "gpio36",
 416                                                "gpio37", "gpio38", "gpio39",
 417                                                "gpio40", "gpio41", "gpio42",
 418                                                "gpio43", "gpio44", "gpio45",
 419                                                "gpio46", "gpio47";
 420                                         function = "nand";
 421                                         drive-strength = <10>;
 422                                         bias-disable;
 423                                 };
 424
 425                                 pullups {
 426                                         pins = "gpio39";
 427                                         bias-pull-up;
 428                                 };
 429
 430                                 hold {
 431                                         pins = "gpio40", "gpio41", "gpio42",
 432                                                "gpio43", "gpio44", "gpio45",
 433                                                "gpio46", "gpio47";
 434                                         bias-bus-hold;
 435                                 };
 436                         };
 437                 };
 438
 439                 intc: interrupt-controller@2000000 {
 440                         compatible = "qcom,msm-qgic2";
 441                         interrupt-controller;
 442                         #interrupt-cells = <3>;
 443                         reg = <0x02000000 0x1000>,
 444                               <0x02002000 0x1000>;
 445                 };
 446
 447                 timer@200a000 {
 448                         compatible = "qcom,kpss-timer",
 449                                      "qcom,kpss-wdt-ipq8064", "qcom,msm-timer";
 450                         interrupts = <GIC_PPI 1 (GIC_CPU_MASK_SIMPLE(2) |
 451                                                  IRQ_TYPE_EDGE_RISING)>,
 452                                      <GIC_PPI 2 (GIC_CPU_MASK_SIMPLE(2) |
 453                                                  IRQ_TYPE_EDGE_RISING)>,
 454                                      <GIC_PPI 3 (GIC_CPU_MASK_SIMPLE(2) |
 455                                                  IRQ_TYPE_EDGE_RISING)>,
 456                                      <GIC_PPI 4 (GIC_CPU_MASK_SIMPLE(2) |
 457                                                  IRQ_TYPE_EDGE_RISING)>,
 458                                      <GIC_PPI 5 (GIC_CPU_MASK_SIMPLE(2) |
 459                                                  IRQ_TYPE_EDGE_RISING)>;
 460                         reg = <0x0200a000 0x100>;
 461                         clock-frequency = <25000000>,
 462                                           <32768>;
 463                         clocks = <&sleep_clk>;
 464                         clock-names = "sleep";
 465                         cpu-offset = <0x80000>;
 466                 };
 467
 468                 acc0: clock-controller@2088000 {
 469                         compatible = "qcom,kpss-acc-v1";
 470                         reg = <0x02088000 0x1000>, <0x02008000 0x1000>;
 471                 };
 472
 473                 acc1: clock-controller@2098000 {
 474                         compatible = "qcom,kpss-acc-v1";
 475                         reg = <0x02098000 0x1000>, <0x02008000 0x1000>;
 476                 };
 477
 478                 adm_dma: dma-controller@18300000 {
 479                         compatible = "qcom,adm";
 480                         reg = <0x18300000 0x100000>;
 481                         interrupts = <GIC_SPI 170 IRQ_TYPE_LEVEL_HIGH>;
 482                         #dma-cells = <1>;
 483
 484                         clocks = <&gcc ADM0_CLK>, <&gcc ADM0_PBUS_CLK>;
 485                         clock-names = "core", "iface";
 486
 487                         resets = <&gcc ADM0_RESET>,
 488                                  <&gcc ADM0_PBUS_RESET>,
 489                                  <&gcc ADM0_C0_RESET>,
 490                                  <&gcc ADM0_C1_RESET>,
 491                                  <&gcc ADM0_C2_RESET>;
 492                         reset-names = "clk", "pbus", "c0", "c1", "c2";
 493                         qcom,ee = <0>;
 494
 495                         status = "disabled";
 496                 };
 497
 498                 saw0: regulator@2089000 {
 499                         compatible = "qcom,saw2";
 500                         reg = <0x02089000 0x1000>, <0x02009000 0x1000>;
 501                         regulator;
 502                 };
 503
 504                 saw1: regulator@2099000 {
 505                         compatible = "qcom,saw2";
 506                         reg = <0x02099000 0x1000>, <0x02009000 0x1000>;
 507                         regulator;
 508                 };
 509
 510                 gsbi2: gsbi@12480000 {
 511                         compatible = "qcom,gsbi-v1.0.0";
 512                         cell-index = <2>;
 513                         reg = <0x12480000 0x100>;
 514                         clocks = <&gcc GSBI2_H_CLK>;
 515                         clock-names = "iface";
 516                         #address-cells = <1>;
 517                         #size-cells = <1>;
 518                         ranges;
 519                         status = "disabled";
 520
 521                         syscon-tcsr = <&tcsr>;
 522
 523                         gsbi2_serial: serial@12490000 {
 524                                 compatible = "qcom,msm-uartdm-v1.3", "qcom,msm-uartdm";
 525                                 reg = <0x12490000 0x1000>,
 526                                       <0x12480000 0x1000>;
 527                                 interrupts = <GIC_SPI 195 IRQ_TYPE_LEVEL_HIGH>;
 528                                 clocks = <&gcc GSBI2_UART_CLK>, <&gcc GSBI2_H_CLK>;
 529                                 clock-names = "core", "iface";
 530                                 status = "disabled";
 531                         };
 532
 533                         i2c@124a0000 {
 534                                 compatible = "qcom,i2c-qup-v1.1.1";
 535                                 reg = <0x124a0000 0x1000>;
 536                                 interrupts = <GIC_SPI 196 IRQ_TYPE_LEVEL_HIGH>;
 537
 538                                 clocks = <&gcc GSBI2_QUP_CLK>, <&gcc GSBI2_H_CLK>;
 539                                 clock-names = "core", "iface";
 540                                 status = "disabled";
 541
 542                                 #address-cells = <1>;
 543                                 #size-cells = <0>;
 544                         };
 545                 };
 546
 547                 gsbi4: gsbi@16300000 {
 548                         compatible = "qcom,gsbi-v1.0.0";
 549                         cell-index = <4>;
 550                         reg = <0x16300000 0x100>;
 551                         clocks = <&gcc GSBI4_H_CLK>;
 552                         clock-names = "iface";
 553                         #address-cells = <1>;
 554                         #size-cells = <1>;
 555                         ranges;
 556                         status = "disabled";
 557
 558                         syscon-tcsr = <&tcsr>;
 559
 560                         gsbi4_serial: serial@16340000 {
 561                                 compatible = "qcom,msm-uartdm-v1.3", "qcom,msm-uartdm";
 562                                 reg = <0x16340000 0x1000>,
 563                                       <0x16300000 0x1000>;
 564                                 interrupts = <GIC_SPI 152 IRQ_TYPE_LEVEL_HIGH>;
 565                                 clocks = <&gcc GSBI4_UART_CLK>, <&gcc GSBI4_H_CLK>;
 566                                 clock-names = "core", "iface";
 567                                 status = "disabled";
 568                         };
 569
 570                         i2c@16380000 {
 571                                 compatible = "qcom,i2c-qup-v1.1.1";
 572                                 reg = <0x16380000 0x1000>;
 573                                 interrupts = <GIC_SPI 153 IRQ_TYPE_LEVEL_HIGH>;
 574
 575                                 clocks = <&gcc GSBI4_QUP_CLK>, <&gcc GSBI4_H_CLK>;
 576                                 clock-names = "core", "iface";
 577                                 status = "disabled";
 578
 579                                 #address-cells = <1>;
 580                                 #size-cells = <0>;
 581                         };
 582                 };
 583
 584                 gsbi5: gsbi@1a200000 {
 585                         compatible = "qcom,gsbi-v1.0.0";
 586                         cell-index = <5>;
 587                         reg = <0x1a200000 0x100>;
 588                         clocks = <&gcc GSBI5_H_CLK>;
 589                         clock-names = "iface";
 590                         #address-cells = <1>;
 591                         #size-cells = <1>;
 592                         ranges;
 593                         status = "disabled";
 594
 595                         syscon-tcsr = <&tcsr>;
 596
 597                         gsbi5_serial: serial@1a240000 {
 598                                 compatible = "qcom,msm-uartdm-v1.3", "qcom,msm-uartdm";
 599                                 reg = <0x1a240000 0x1000>,
 600                                       <0x1a200000 0x1000>;
 601                                 interrupts = <GIC_SPI 154 IRQ_TYPE_LEVEL_HIGH>;
 602                                 clocks = <&gcc GSBI5_UART_CLK>, <&gcc GSBI5_H_CLK>;
 603                                 clock-names = "core", "iface";
 604                                 status = "disabled";
 605                         };
 606
 607                         i2c@1a280000 {
 608                                 compatible = "qcom,i2c-qup-v1.1.1";
 609                                 reg = <0x1a280000 0x1000>;
 610                                 interrupts = <GIC_SPI 155 IRQ_TYPE_LEVEL_HIGH>;
 611
 612                                 clocks = <&gcc GSBI5_QUP_CLK>, <&gcc GSBI5_H_CLK>;
 613                                 clock-names = "core", "iface";
 614                                 status = "disabled";
 615
 616                                 #address-cells = <1>;
 617                                 #size-cells = <0>;
 618                         };
 619
 620                         spi@1a280000 {
 621                                 compatible = "qcom,spi-qup-v1.1.1";
 622                                 reg = <0x1a280000 0x1000>;
 623                                 interrupts = <GIC_SPI 155 IRQ_TYPE_LEVEL_HIGH>;
 624
 625                                 clocks = <&gcc GSBI5_QUP_CLK>, <&gcc GSBI5_H_CLK>;
 626                                 clock-names = "core", "iface";
 627                                 status = "disabled";
 628
 629                                 #address-cells = <1>;
 630                                 #size-cells = <0>;
 631                         };
 632                 };
 633
 634                 gsbi7: gsbi@16600000 {
 635                         status = "disabled";
 636                         compatible = "qcom,gsbi-v1.0.0";
 637                         cell-index = <7>;
 638                         reg = <0x16600000 0x100>;
 639                         clocks = <&gcc GSBI7_H_CLK>;
 640                         clock-names = "iface";
 641                         #address-cells = <1>;
 642                         #size-cells = <1>;
 643                         ranges;
 644                         syscon-tcsr = <&tcsr>;
 645
 646                         gsbi7_serial: serial@16640000 {
 647                                 compatible = "qcom,msm-uartdm-v1.3", "qcom,msm-uartdm";
 648                                 reg = <0x16640000 0x1000>,
 649                                       <0x16600000 0x1000>;
 650                                 interrupts = <GIC_SPI 158 IRQ_TYPE_LEVEL_HIGH>;
 651                                 clocks = <&gcc GSBI7_UART_CLK>, <&gcc GSBI7_H_CLK>;
 652                                 clock-names = "core", "iface";
 653                                 status = "disabled";
 654                         };
 655                 };
 656
 657                 rng@1a500000 {
 658                         compatible = "qcom,prng";
 659                         reg = <0x1a500000 0x200>;
 660                         clocks = <&gcc PRNG_CLK>;
 661                         clock-names = "core";
 662                 };
 663
 664                 sata_phy: sata-phy@1b400000 {
 665                         compatible = "qcom,ipq806x-sata-phy";
 666                         reg = <0x1b400000 0x200>;
 667
 668                         clocks = <&gcc SATA_PHY_CFG_CLK>;
 669                         clock-names = "cfg";
 670
 671                         #phy-cells = <0>;
 672                         status = "disabled";
 673                 };
 674
 675                 nand: nand-controller@1ac00000 {
 676                         compatible = "qcom,ipq806x-nand";
 677                         reg = <0x1ac00000 0x800>;
 678
 679                         pinctrl-0 = <&nand_pins>;
 680                         pinctrl-names = "default";
 681
 682                         clocks = <&gcc EBI2_CLK>,
 683                                  <&gcc EBI2_AON_CLK>;
 684                         clock-names = "core", "aon";
 685
 686                         dmas = <&adm_dma 3>;
 687                         dma-names = "rxtx";
 688                         qcom,cmd-crci = <15>;
 689                         qcom,data-crci = <3>;
 690
 691                         #address-cells = <1>;
 692                         #size-cells = <0>;
 693
 694                         status = "disabled";
 695                 };
 696
 697                 sata: sata@29000000 {
 698                         compatible = "qcom,ipq806x-ahci", "generic-ahci";
 699                         reg = <0x29000000 0x180>;
 700
 701                         interrupts = <GIC_SPI 209 IRQ_TYPE_LEVEL_HIGH>;
 702
 703                         clocks = <&gcc SFAB_SATA_S_H_CLK>,
 704                                  <&gcc SATA_H_CLK>,
 705                                  <&gcc SATA_A_CLK>,
 706                                  <&gcc SATA_RXOOB_CLK>,
 707                                  <&gcc SATA_PMALIVE_CLK>;
 708                         clock-names = "slave_face", "iface", "core",
 709                                         "rxoob", "pmalive";
 710
 711                         assigned-clocks = <&gcc SATA_RXOOB_CLK>, <&gcc SATA_PMALIVE_CLK>;
 712                         assigned-clock-rates = <100000000>, <100000000>;
 713
 714                         phys = <&sata_phy>;
 715                         phy-names = "sata-phy";
 716                         status = "disabled";
 717                 };
 718
 719                 qcom,ssbi@500000 {
 720                         compatible = "qcom,ssbi";
 721                         reg = <0x00500000 0x1000>;
 722                         qcom,controller-type = "pmic-arbiter";
 723                 };
 724
 725                 qfprom: qfprom@700000 {
 726                         compatible = "qcom,qfprom";
 727                         reg = <0x00700000 0x1000>;
 728                         #address-cells = <1>;
 729                         #size-cells = <1>;
 730                         tsens_calib: calib@400 {
 731                                 reg = <0x400 0xb>;
 732                         };
 733                         tsens_calib_backup: calib_backup@410 {
 734                                 reg = <0x410 0xb>;
 735                         };
 736                 };
 737
 738                 gcc: clock-controller@900000 {
 739                         compatible = "qcom,gcc-ipq8064";
 740                         reg = <0x00900000 0x4000>;
 741                         #clock-cells = <1>;
 742                         #reset-cells = <1>;
 743                         #power-domain-cells = <1>;
 744
 745                         tsens: thermal-sensor@900000 {
 746                                 compatible = "qcom,ipq8064-tsens";
 747
 748                                 nvmem-cells = <&tsens_calib>, <&tsens_calib_backup>;
 749                                 nvmem-cell-names = "calib", "calib_backup";
 750                                 interrupts = <GIC_SPI 178 IRQ_TYPE_LEVEL_HIGH>;
 751                                 interrupt-names = "uplow";
 752
 753                                 #qcom,sensors = <11>;
 754                                 #thermal-sensor-cells = <1>;
 755                         };
 756                 };
 757
 758                 rpm: rpm@108000 {
 759                         compatible = "qcom,rpm-ipq8064";
 760                         reg = <0x108000 0x1000>;
 761                         qcom,ipc = <&l2cc 0x8 2>;
 762
 763                         interrupts = <GIC_SPI 19 IRQ_TYPE_LEVEL_HIGH>,
 764                                         <GIC_SPI 21 IRQ_TYPE_LEVEL_HIGH>,
 765                                         <GIC_SPI 22 IRQ_TYPE_LEVEL_HIGH>;
 766                         interrupt-names = "ack", "err", "wakeup";
 767
 768                         clocks = <&gcc RPM_MSG_RAM_H_CLK>;
 769                         clock-names = "ram";
 770
 771                         rpmcc: clock-controller {
 772                                 compatible = "qcom,rpmcc-ipq806x", "qcom,rpmcc";
 773                                 #clock-cells = <1>;
 774                         };
 775                 };
 776
 777                 tcsr: syscon@1a400000 {
 778                         compatible = "qcom,tcsr-ipq8064", "syscon";
 779                         reg = <0x1a400000 0x100>;
 780                 };
 781
 782                 l2cc: clock-controller@2011000 {
 783                         compatible = "qcom,kpss-gcc", "syscon";
 784                         reg = <0x2011000 0x1000>;
 785                         clocks = <&gcc PLL8_VOTE>, <&gcc PXO_SRC>;
 786                         clock-names = "pll8_vote", "pxo";
 787                         clock-output-names = "acpu_l2_aux";
 788                 };
 789
 790                 lcc: clock-controller@28000000 {
 791                         compatible = "qcom,lcc-ipq8064";
 792                         reg = <0x28000000 0x1000>;
 793                         #clock-cells = <1>;
 794                         #reset-cells = <1>;
 795                 };
 796
 797                 pcie0: pci@1b500000 {
 798                         compatible = "qcom,pcie-ipq8064";
 799                         reg = <0x1b500000 0x1000
 800                                0x1b502000 0x80
 801                                0x1b600000 0x100
 802                                0x0ff00000 0x100000>;
 803                         reg-names = "dbi", "elbi", "parf", "config";
 804                         device_type = "pci";
 805                         linux,pci-domain = <0>;
 806                         bus-range = <0x00 0xff>;
 807                         num-lanes = <1>;
 808                         #address-cells = <3>;
 809                         #size-cells = <2>;
 810
 811                         ranges = <0x81000000 0 0x0fe00000 0x0fe00000 0 0x00100000   /* downstream I/O */
 812                                   0x82000000 0 0x08000000 0x08000000 0 0x07e00000>; /* non-prefetchable memory */
 813
 814                         interrupts = <GIC_SPI 35 IRQ_TYPE_LEVEL_HIGH>;
 815                         interrupt-names = "msi";
 816                         #interrupt-cells = <1>;
 817                         interrupt-map-mask = <0 0 0 0x7>;
 818                         interrupt-map = <0 0 0 1 &intc 0 36 IRQ_TYPE_LEVEL_HIGH>, /* int_a */
 819                                         <0 0 0 2 &intc 0 37 IRQ_TYPE_LEVEL_HIGH>, /* int_b */
 820                                         <0 0 0 3 &intc 0 38 IRQ_TYPE_LEVEL_HIGH>, /* int_c */
 821                                         <0 0 0 4 &intc 0 39 IRQ_TYPE_LEVEL_HIGH>; /* int_d */
 822
 823                         clocks = <&gcc PCIE_A_CLK>,
 824                                  <&gcc PCIE_H_CLK>,
 825                                  <&gcc PCIE_PHY_CLK>,
 826                                  <&gcc PCIE_AUX_CLK>,
 827                                  <&gcc PCIE_ALT_REF_CLK>;
 828                         clock-names = "core", "iface", "phy", "aux", "ref";
 829
 830                         assigned-clocks = <&gcc PCIE_ALT_REF_CLK>;
 831                         assigned-clock-rates = <100000000>;
 832
 833                         resets = <&gcc PCIE_ACLK_RESET>,
 834                                  <&gcc PCIE_HCLK_RESET>,
 835                                  <&gcc PCIE_POR_RESET>,
 836                                  <&gcc PCIE_PCI_RESET>,
 837                                  <&gcc PCIE_PHY_RESET>,
 838                                  <&gcc PCIE_EXT_RESET>;
 839                         reset-names = "axi", "ahb", "por", "pci", "phy", "ext";
 840
 841                         pinctrl-0 = <&pcie0_pins>;
 842                         pinctrl-names = "default";
 843
 844                         status = "disabled";
 845                         perst-gpio = <&qcom_pinmux 3 GPIO_ACTIVE_LOW>;
 846                 };
 847
 848                 pcie1: pci@1b700000 {
 849                         compatible = "qcom,pcie-ipq8064";
 850                         reg = <0x1b700000 0x1000
 851                                0x1b702000 0x80
 852                                0x1b800000 0x100
 853                                0x31f00000 0x100000>;
 854                         reg-names = "dbi", "elbi", "parf", "config";
 855                         device_type = "pci";
 856                         linux,pci-domain = <1>;
 857                         bus-range = <0x00 0xff>;
 858                         num-lanes = <1>;
 859                         #address-cells = <3>;
 860                         #size-cells = <2>;
 861
 862                         ranges = <0x81000000 0 0x31e00000 0x31e00000 0 0x00100000   /* downstream I/O */
 863                                   0x82000000 0 0x2e000000 0x2e000000 0 0x03e00000>; /* non-prefetchable memory */
 864
 865                         interrupts = <GIC_SPI 57 IRQ_TYPE_LEVEL_HIGH>;
 866                         interrupt-names = "msi";
 867                         #interrupt-cells = <1>;
 868                         interrupt-map-mask = <0 0 0 0x7>;
 869                         interrupt-map = <0 0 0 1 &intc 0 58 IRQ_TYPE_LEVEL_HIGH>, /* int_a */
 870                                         <0 0 0 2 &intc 0 59 IRQ_TYPE_LEVEL_HIGH>, /* int_b */
 871                                         <0 0 0 3 &intc 0 60 IRQ_TYPE_LEVEL_HIGH>, /* int_c */
 872                                         <0 0 0 4 &intc 0 61 IRQ_TYPE_LEVEL_HIGH>; /* int_d */
 873
 874                         clocks = <&gcc PCIE_1_A_CLK>,
 875                                  <&gcc PCIE_1_H_CLK>,
 876                                  <&gcc PCIE_1_PHY_CLK>,
 877                                  <&gcc PCIE_1_AUX_CLK>,
 878                                  <&gcc PCIE_1_ALT_REF_CLK>;
 879                         clock-names = "core", "iface", "phy", "aux", "ref";
 880
 881                         assigned-clocks = <&gcc PCIE_1_ALT_REF_CLK>;
 882                         assigned-clock-rates = <100000000>;
 883
 884                         resets = <&gcc PCIE_1_ACLK_RESET>,
 885                                  <&gcc PCIE_1_HCLK_RESET>,
 886                                  <&gcc PCIE_1_POR_RESET>,
 887                                  <&gcc PCIE_1_PCI_RESET>,
 888                                  <&gcc PCIE_1_PHY_RESET>,
 889                                  <&gcc PCIE_1_EXT_RESET>;
 890                         reset-names = "axi", "ahb", "por", "pci", "phy", "ext";
 891
 892                         pinctrl-0 = <&pcie1_pins>;
 893                         pinctrl-names = "default";
 894
 895                         status = "disabled";
 896                         perst-gpio = <&qcom_pinmux 48 GPIO_ACTIVE_LOW>;
 897                 };
 898
 899                 pcie2: pci@1b900000 {
 900                         compatible = "qcom,pcie-ipq8064";
 901                         reg = <0x1b900000 0x1000
 902                                0x1b902000 0x80
 903                                0x1ba00000 0x100
 904                                0x35f00000 0x100000>;
 905                         reg-names = "dbi", "elbi", "parf", "config";
 906                         device_type = "pci";
 907                         linux,pci-domain = <2>;
 908                         bus-range = <0x00 0xff>;
 909                         num-lanes = <1>;
 910                         #address-cells = <3>;
 911                         #size-cells = <2>;
 912
 913                         ranges = <0x81000000 0 0x35e00000 0x35e00000 0 0x00100000   /* downstream I/O */
 914                                   0x82000000 0 0x32000000 0x32000000 0 0x03e00000>; /* non-prefetchable memory */
 915
 916                         interrupts = <GIC_SPI 71 IRQ_TYPE_LEVEL_HIGH>;
 917                         interrupt-names = "msi";
 918                         #interrupt-cells = <1>;
 919                         interrupt-map-mask = <0 0 0 0x7>;
 920                         interrupt-map = <0 0 0 1 &intc 0 72 IRQ_TYPE_LEVEL_HIGH>, /* int_a */
 921                                         <0 0 0 2 &intc 0 73 IRQ_TYPE_LEVEL_HIGH>, /* int_b */
 922                                         <0 0 0 3 &intc 0 74 IRQ_TYPE_LEVEL_HIGH>, /* int_c */
 923                                         <0 0 0 4 &intc 0 75 IRQ_TYPE_LEVEL_HIGH>; /* int_d */
 924
 925                         clocks = <&gcc PCIE_2_A_CLK>,
 926                                  <&gcc PCIE_2_H_CLK>,
 927                                  <&gcc PCIE_2_PHY_CLK>,
 928                                  <&gcc PCIE_2_AUX_CLK>,
 929                                  <&gcc PCIE_2_ALT_REF_CLK>;
 930                         clock-names = "core", "iface", "phy", "aux", "ref";
 931
 932                         assigned-clocks = <&gcc PCIE_2_ALT_REF_CLK>;
 933                         assigned-clock-rates = <100000000>;
 934
 935                         resets = <&gcc PCIE_2_ACLK_RESET>,
 936                                  <&gcc PCIE_2_HCLK_RESET>,
 937                                  <&gcc PCIE_2_POR_RESET>,
 938                                  <&gcc PCIE_2_PCI_RESET>,
 939                                  <&gcc PCIE_2_PHY_RESET>,
 940                                  <&gcc PCIE_2_EXT_RESET>;
 941                         reset-names = "axi", "ahb", "por", "pci", "phy", "ext";
 942
 943                         pinctrl-0 = <&pcie2_pins>;
 944                         pinctrl-names = "default";
 945
 946                         status = "disabled";
 947                         perst-gpio = <&qcom_pinmux 63 GPIO_ACTIVE_LOW>;
 948                 };
 949
 950                 nss_common: syscon@03000000 {
 951                         compatible = "syscon";
 952                         reg = <0x03000000 0x0000FFFF>;
 953                 };
 954
 955                 qsgmii_csr: syscon@1bb00000 {
 956                         compatible = "syscon";
 957                         reg = <0x1bb00000 0x000001FF>;
 958                 };
 959
 960                 stmmac_axi_setup: stmmac-axi-config {
 961                         snps,wr_osr_lmt = <7>;
 962                         snps,rd_osr_lmt = <7>;
 963                         snps,blen = <16 0 0 0 0 0 0>;
 964                 };
 965
 966                 gmac0: ethernet@37000000 {
 967                         device_type = "network";
 968                         compatible = "qcom,ipq806x-gmac";
 969                         reg = <0x37000000 0x200000>;
 970                         interrupts = <GIC_SPI 220 IRQ_TYPE_LEVEL_HIGH>;
 971                         interrupt-names = "macirq";
 972
 973                         snps,axi-config = <&stmmac_axi_setup>;
 974                         snps,pbl = <32>;
 975                         snps,aal;
 976
 977                         qcom,nss-common = <&nss_common>;
 978                         qcom,qsgmii-csr = <&qsgmii_csr>;
 979
 980                         clocks = <&gcc GMAC_CORE1_CLK>;
 981                         clock-names = "stmmaceth";
 982
 983                         resets = <&gcc GMAC_CORE1_RESET>,
 984                                  <&gcc GMAC_AHB_RESET>;
 985                         reset-names = "stmmaceth", "ahb";
 986
 987                         status = "disabled";
 988                 };
 989
 990                 gmac1: ethernet@37200000 {
 991                         device_type = "network";
 992                         compatible = "qcom,ipq806x-gmac";
 993                         reg = <0x37200000 0x200000>;
 994                         interrupts = <GIC_SPI 223 IRQ_TYPE_LEVEL_HIGH>;
 995                         interrupt-names = "macirq";
 996
 997                         snps,axi-config = <&stmmac_axi_setup>;
 998                         snps,pbl = <32>;
 999                         snps,aal;
1000
1001                         qcom,nss-common = <&nss_common>;
1002                         qcom,qsgmii-csr = <&qsgmii_csr>;
1003
1004                         clocks = <&gcc GMAC_CORE2_CLK>;
1005                         clock-names = "stmmaceth";
1006
1007                         resets = <&gcc GMAC_CORE2_RESET>,
1008                                  <&gcc GMAC_AHB_RESET>;
1009                         reset-names = "stmmaceth", "ahb";
1010
1011                         status = "disabled";
1012                 };
1013
1014                 gmac2: ethernet@37400000 {
1015                         device_type = "network";
1016                         compatible = "qcom,ipq806x-gmac";
1017                         reg = <0x37400000 0x200000>;
1018                         interrupts = <GIC_SPI 226 IRQ_TYPE_LEVEL_HIGH>;
1019                         interrupt-names = "macirq";
1020
1021                         snps,axi-config = <&stmmac_axi_setup>;
1022                         snps,pbl = <32>;
1023                         snps,aal;
1024
1025                         qcom,nss-common = <&nss_common>;
1026                         qcom,qsgmii-csr = <&qsgmii_csr>;
1027
1028                         clocks = <&gcc GMAC_CORE3_CLK>;
1029                         clock-names = "stmmaceth";
1030
1031                         resets = <&gcc GMAC_CORE3_RESET>,
1032                                  <&gcc GMAC_AHB_RESET>;
1033                         reset-names = "stmmaceth", "ahb";
1034
1035                         status = "disabled";
1036                 };
1037
1038                 gmac3: ethernet@37600000 {
1039                         device_type = "network";
1040                         compatible = "qcom,ipq806x-gmac";
1041                         reg = <0x37600000 0x200000>;
1042                         interrupts = <GIC_SPI 229 IRQ_TYPE_LEVEL_HIGH>;
1043                         interrupt-names = "macirq";
1044
1045                         snps,axi-config = <&stmmac_axi_setup>;
1046                         snps,pbl = <32>;
1047                         snps,aal;
1048
1049                         qcom,nss-common = <&nss_common>;
1050                         qcom,qsgmii-csr = <&qsgmii_csr>;
1051
1052                         clocks = <&gcc GMAC_CORE4_CLK>;
1053                         clock-names = "stmmaceth";
1054
1055                         resets = <&gcc GMAC_CORE4_RESET>,
1056                                  <&gcc GMAC_AHB_RESET>;
1057                         reset-names = "stmmaceth", "ahb";
1058
1059                         status = "disabled";
1060                 };
1061
1062                 hs_phy_0: phy@100f8800 {
1063                         compatible = "qcom,ipq806x-usb-phy-hs";
1064                         reg = <0x100f8800 0x30>;
1065                         clocks = <&gcc USB30_0_UTMI_CLK>;
1066                         clock-names = "ref";
1067                         #phy-cells = <0>;
1068
1069                         status = "disabled";
1070                 };
1071
1072                 ss_phy_0: phy@100f8830 {
1073                         compatible = "qcom,ipq806x-usb-phy-ss";
1074                         reg = <0x100f8830 0x30>;
1075                         clocks = <&gcc USB30_0_MASTER_CLK>;
1076                         clock-names = "ref";
1077                         #phy-cells = <0>;
1078
1079                         status = "disabled";
1080                 };
1081
1082                 usb3_0: usb3@100f8800 {
1083                         compatible = "qcom,ipq8064-dwc3", "qcom,dwc3";
1084                         #address-cells = <1>;
1085                         #size-cells = <1>;
1086                         reg = <0x100f8800 0x8000>;
1087                         clocks = <&gcc USB30_0_MASTER_CLK>;
1088                         clock-names = "core";
1089
1090                         ranges;
1091
1092                         resets = <&gcc USB30_0_MASTER_RESET>;
1093                         reset-names = "master";
1094
1095                         status = "disabled";
1096
1097                         dwc3_0: dwc3@10000000 {
1098                                 compatible = "snps,dwc3";
1099                                 reg = <0x10000000 0xcd00>;
1100                                 interrupts = <GIC_SPI 205 IRQ_TYPE_LEVEL_HIGH>;
1101                                 phys = <&hs_phy_0>, <&ss_phy_0>;
1102                                 phy-names = "usb2-phy", "usb3-phy";
1103                                 dr_mode = "host";
1104                                 snps,dis_u3_susphy_quirk;
1105                         };
1106                 };
1107
1108                 hs_phy_1: phy@110f8800 {
1109                         compatible = "qcom,ipq806x-usb-phy-hs";
1110                         reg = <0x110f8800 0x30>;
1111                         clocks = <&gcc USB30_1_UTMI_CLK>;
1112                         clock-names = "ref";
1113                         #phy-cells = <0>;
1114                 };
1115
1116                 ss_phy_1: phy@110f8830 {
1117                         compatible = "qcom,ipq806x-usb-phy-ss";
1118                         reg = <0x110f8830 0x30>;
1119                         clocks = <&gcc USB30_1_MASTER_CLK>;
1120                         clock-names = "ref";
1121                         #phy-cells = <0>;
1122                 };
1123
1124                 usb3_1: usb3@110f8800 {
1125                         compatible = "qcom,ipq8064-dwc3", "qcom,dwc3";
1126                         #address-cells = <1>;
1127                         #size-cells = <1>;
1128                         reg = <0x110f8800 0x8000>;
1129                         clocks = <&gcc USB30_1_MASTER_CLK>;
1130                         clock-names = "core";
1131
1132                         ranges;
1133
1134                         resets = <&gcc USB30_1_MASTER_RESET>;
1135                         reset-names = "master";
1136
1137                         status = "disabled";
1138
1139                         dwc3_1: dwc3@11000000 {
1140                                 compatible = "snps,dwc3";
1141                                 reg = <0x11000000 0xcd00>;
1142                                 interrupts = <GIC_SPI 110 IRQ_TYPE_LEVEL_HIGH>;
1143                                 phys = <&hs_phy_1>, <&ss_phy_1>;
1144                                 phy-names = "usb2-phy", "usb3-phy";
1145                                 dr_mode = "host";
1146                                 snps,dis_u3_susphy_quirk;
1147                         };
1148                 };
1149
1150                 vsdcc_fixed: vsdcc-regulator {
1151                         compatible = "regulator-fixed";
1152                         regulator-name = "SDCC Power";
1153                         regulator-min-microvolt = <3300000>;
1154                         regulator-max-microvolt = <3300000>;
1155                         regulator-always-on;
1156                 };
1157
1158                 sdcc1bam: dma@12402000 {
1159                         compatible = "qcom,bam-v1.3.0";
1160                         reg = <0x12402000 0x8000>;
1161                         interrupts = <GIC_SPI 98 IRQ_TYPE_LEVEL_HIGH>;
1162                         clocks = <&gcc SDC1_H_CLK>;
1163                         clock-names = "bam_clk";
1164                         #dma-cells = <1>;
1165                         qcom,ee = <0>;
1166                 };
1167
1168                 sdcc3bam: dma@12182000 {
1169                         compatible = "qcom,bam-v1.3.0";
1170                         reg = <0x12182000 0x8000>;
1171                         interrupts = <GIC_SPI 96 IRQ_TYPE_LEVEL_HIGH>;
1172                         clocks = <&gcc SDC3_H_CLK>;
1173                         clock-names = "bam_clk";
1174                         #dma-cells = <1>;
1175                         qcom,ee = <0>;
1176                 };
1177
1178                 amba: amba {
1179                         compatible = "simple-bus";
1180                         #address-cells = <1>;
1181                         #size-cells = <1>;
1182                         ranges;
1183
1184                         sdcc1: mmc@12400000 {
1185                                 status          = "disabled";
1186                                 compatible      = "arm,pl18x", "arm,primecell";
1187                                 arm,primecell-periphid = <0x00051180>;
1188                                 reg             = <0x12400000 0x2000>;
1189                                 interrupts      = <GIC_SPI 104 IRQ_TYPE_LEVEL_HIGH>;
1190                                 interrupt-names = "cmd_irq";
1191                                 clocks          = <&gcc SDC1_CLK>, <&gcc SDC1_H_CLK>;
1192                                 clock-names     = "mclk", "apb_pclk";
1193                                 bus-width       = <8>;
1194                                 max-frequency   = <96000000>;
1195                                 non-removable;
1196                                 cap-sd-highspeed;
1197                                 cap-mmc-highspeed;
1198                                 mmc-ddr-1_8v;
1199                                 vmmc-supply = <&vsdcc_fixed>;
1200                                 dmas = <&sdcc1bam 2>, <&sdcc1bam 1>;
1201                                 dma-names = "tx", "rx";
1202                         };
1203
1204                         sdcc3: mmc@12180000 {
1205                                 compatible      = "arm,pl18x", "arm,primecell";
1206                                 arm,primecell-periphid = <0x00051180>;
1207                                 status          = "disabled";
1208                                 reg             = <0x12180000 0x2000>;
1209                                 interrupts      = <GIC_SPI 102 IRQ_TYPE_LEVEL_HIGH>;
1210                                 interrupt-names = "cmd_irq";
1211                                 clocks          = <&gcc SDC3_CLK>, <&gcc SDC3_H_CLK>;
1212                                 clock-names     = "mclk", "apb_pclk";
1213                                 bus-width       = <8>;
1214                                 cap-sd-highspeed;
1215                                 cap-mmc-highspeed;
1216                                 max-frequency   = <192000000>;
1217                                 sd-uhs-sdr104;
1218                                 sd-uhs-ddr50;
1219                                 vqmmc-supply = <&vsdcc_fixed>;
1220                                 dmas = <&sdcc3bam 2>, <&sdcc3bam 1>;
1221                                 dma-names = "tx", "rx";
1222                         };
1223                 };
1224         };
1225 };