ARM: dts: bcm283x: Remove gpio line name NC
[platform/kernel/linux-starfive.git] / arch / arm / boot / dts / bcm2837-rpi-3-b.dts
1 // SPDX-License-Identifier: GPL-2.0
2 /dts-v1/;
3 #include "bcm2837.dtsi"
4 #include "bcm2836-rpi.dtsi"
5 #include "bcm283x-rpi-smsc9514.dtsi"
6 #include "bcm283x-rpi-usb-host.dtsi"
7 #include "bcm283x-rpi-wifi-bt.dtsi"
8
9 / {
10         compatible = "raspberrypi,3-model-b", "brcm,bcm2837";
11         model = "Raspberry Pi 3 Model B";
12
13         chosen {
14                 /* 8250 auxiliary UART instead of pl011 */
15                 stdout-path = "serial1:115200n8";
16         };
17
18         memory@0 {
19                 device_type = "memory";
20                 reg = <0 0x40000000>;
21         };
22
23         leds {
24                 led-act {
25                         gpios = <&expgpio 2 GPIO_ACTIVE_HIGH>;
26                 };
27         };
28 };
29
30 &bt {
31         shutdown-gpios = <&expgpio 0 GPIO_ACTIVE_HIGH>;
32 };
33
34 &firmware {
35         expgpio: gpio {
36                 compatible = "raspberrypi,firmware-gpio";
37                 gpio-controller;
38                 #gpio-cells = <2>;
39                 gpio-line-names = "BT_ON",
40                                   "WL_ON",
41                                   "STATUS_LED",
42                                   "LAN_RUN",
43                                   "HDMI_HPD_N",
44                                   "CAM_GPIO0",
45                                   "CAM_GPIO1",
46                                   "PWR_LOW_N";
47                 status = "okay";
48         };
49 };
50
51 &gpio {
52         /*
53          * Taken from rpi_SCH_3b_1p2_reduced.pdf and
54          * the official GPU firmware DT blob.
55          *
56          * Legend:
57          * "FOO" = GPIO line named "FOO" on the schematic
58          * "FOO_N" = GPIO line named "FOO" on schematic, active low
59          */
60         gpio-line-names = "ID_SDA",
61                           "ID_SCL",
62                           "SDA1",
63                           "SCL1",
64                           "GPIO_GCLK",
65                           "GPIO5",
66                           "GPIO6",
67                           "SPI_CE1_N",
68                           "SPI_CE0_N",
69                           "SPI_MISO",
70                           "SPI_MOSI",
71                           "SPI_SCLK",
72                           "GPIO12",
73                           "GPIO13",
74                           /* Serial port */
75                           "TXD1",
76                           "RXD1",
77                           "GPIO16",
78                           "GPIO17",
79                           "GPIO18",
80                           "GPIO19",
81                           "GPIO20",
82                           "GPIO21",
83                           "GPIO22",
84                           "GPIO23",
85                           "GPIO24",
86                           "GPIO25",
87                           "GPIO26",
88                           "GPIO27",
89                           "", /* GPIO 28 */
90                           "LAN_RUN_BOOT",
91                           /* Used by BT module */
92                           "CTS0",
93                           "RTS0",
94                           "TXD0",
95                           "RXD0",
96                           /* Used by Wifi */
97                           "SD1_CLK",
98                           "SD1_CMD",
99                           "SD1_DATA0",
100                           "SD1_DATA1",
101                           "SD1_DATA2",
102                           "SD1_DATA3",
103                           "PWM0_OUT",
104                           "PWM1_OUT",
105                           "ETHCLK",
106                           "WIFI_CLK",
107                           "SDA0",
108                           "SCL0",
109                           "SMPS_SCL",
110                           "SMPS_SDA",
111                           /* Used by SD Card */
112                           "SD_CLK_R",
113                           "SD_CMD_R",
114                           "SD_DATA0_R",
115                           "SD_DATA1_R",
116                           "SD_DATA2_R",
117                           "SD_DATA3_R";
118 };
119
120 &pwm {
121         pinctrl-names = "default";
122         pinctrl-0 = <&pwm0_gpio40 &pwm1_gpio41>;
123         status = "okay";
124 };
125
126 &hdmi {
127         hpd-gpios = <&expgpio 4 GPIO_ACTIVE_LOW>;
128         power-domains = <&power RPI_POWER_DOMAIN_HDMI>;
129         status = "okay";
130 };
131
132 /* uart0 communicates with the BT module */
133 &uart0 {
134         pinctrl-names = "default";
135         pinctrl-0 = <&uart0_gpio32 &gpclk2_gpio43>;
136 };
137
138 /* uart1 is mapped to the pin header */
139 &uart1 {
140         pinctrl-names = "default";
141         pinctrl-0 = <&uart1_gpio14>;
142         status = "okay";
143 };
144
145 /* SDHOST is used to drive the SD card */
146 &sdhost {
147         pinctrl-names = "default";
148         pinctrl-0 = <&sdhost_gpio48>;
149         status = "okay";
150         bus-width = <4>;
151 };
152
153 &wifi_pwrseq {
154         reset-gpios = <&expgpio 1 GPIO_ACTIVE_LOW>;
155 };