arch/arm/boot/dts/bcm2835-rpi-b.dts

   1 // SPDX-License-Identifier: GPL-2.0
   2 /dts-v1/;
   3 #include "bcm2835.dtsi"
   4 #include "bcm2835-rpi.dtsi"
   5 #include "bcm283x-rpi-smsc9512.dtsi"
   6 #include "bcm283x-rpi-usb-host.dtsi"
   7
   8 / {
   9         compatible = "raspberrypi,model-b", "brcm,bcm2835";
  10         model = "Raspberry Pi Model B";
  11
  12         memory@0 {
  13                 device_type = "memory";
  14                 reg = <0 0x10000000>;
  15         };
  16
  17         leds {
  18                 led-act {
  19                         gpios = <&gpio 16 GPIO_ACTIVE_LOW>;
  20                 };
  21         };
  22 };
  23
  24 &gpio {
  25         /*
  26          * Taken from Raspberry-Pi-Rev-1.0-Model-AB-Schematics.pdf
  27          * RPI00021 sheet 02
  28          *
  29          * Legend:
  30          * "NC" = not connected (no rail from the SoC)
  31          * "FOO" = GPIO line named "FOO" on the schematic
  32          * "FOO_N" = GPIO line named "FOO" on schematic, active low
  33          */
  34         gpio-line-names = "SDA0",
  35                           "SCL0",
  36                           "SDA1",
  37                           "SCL1",
  38                           "GPIO_GCLK",
  39                           "CAM_GPIO1",
  40                           "LAN_RUN",
  41                           "SPI_CE1_N",
  42                           "SPI_CE0_N",
  43                           "SPI_MISO",
  44                           "SPI_MOSI",
  45                           "SPI_SCLK",
  46                           "NC", /* GPIO12 */
  47                           "NC", /* GPIO13 */
  48                           /* Serial port */
  49                           "TXD0",
  50                           "RXD0",
  51                           "STATUS_LED_N",
  52                           "GPIO17",
  53                           "GPIO18",
  54                           "NC", /* GPIO19 */
  55                           "NC", /* GPIO20 */
  56                           "GPIO21",
  57                           "GPIO22",
  58                           "GPIO23",
  59                           "GPIO24",
  60                           "GPIO25",
  61                           "NC", /* GPIO26 */
  62                           "CAM_GPIO0",
  63                           /* Binary number representing build/revision */
  64                           "CONFIG0",
  65                           "CONFIG1",
  66                           "CONFIG2",
  67                           "CONFIG3",
  68                           "NC", /* GPIO32 */
  69                           "NC", /* GPIO33 */
  70                           "NC", /* GPIO34 */
  71                           "NC", /* GPIO35 */
  72                           "NC", /* GPIO36 */
  73                           "NC", /* GPIO37 */
  74                           "NC", /* GPIO38 */
  75                           "NC", /* GPIO39 */
  76                           "PWM0_OUT",
  77                           "NC", /* GPIO41 */
  78                           "NC", /* GPIO42 */
  79                           "NC", /* GPIO43 */
  80                           "NC", /* GPIO44 */
  81                           "PWM1_OUT",
  82                           "HDMI_HPD_P",
  83                           "SD_CARD_DET",
  84                           /* Used by SD Card */
  85                           "SD_CLK_R",
  86                           "SD_CMD_R",
  87                           "SD_DATA0_R",
  88                           "SD_DATA1_R",
  89                           "SD_DATA2_R",
  90                           "SD_DATA3_R";
  91
  92         pinctrl-0 = <&gpioout &alt0>;
  93 };
  94
  95 &hdmi {
  96         hpd-gpios = <&gpio 46 GPIO_ACTIVE_HIGH>;
  97         power-domains = <&power RPI_POWER_DOMAIN_HDMI>;
  98         status = "okay";
  99 };
 100
 101 &pwm {
 102         pinctrl-names = "default";
 103         pinctrl-0 = <&pwm0_gpio40 &pwm1_gpio45>;
 104         status = "okay";
 105 };
 106
 107 &sdhost {
 108         pinctrl-names = "default";
 109         pinctrl-0 = <&sdhost_gpio48>;
 110         bus-width = <4>;
 111         status = "okay";
 112 };
 113
 114 &uart0 {
 115         pinctrl-names = "default";
 116         pinctrl-0 = <&uart0_gpio14>;
 117         status = "okay";
 118 };