1 menu "ARM architecture"
10 select SYS_CACHE_SHIFT_6
13 config POSITION_INDEPENDENT
14 bool "Generate position-independent pre-relocation code"
15 select INIT_SP_RELATIVE
17 U-Boot expects to be linked to a specific hard-coded address, and to
18 be loaded to and run from that address. This option lifts that
19 restriction, thus allowing the code to be loaded to and executed from
20 almost any 4K aligned address. This logic relies on the relocation
21 information that is embedded in the binary to support U-Boot
22 relocating itself to the top-of-RAM later during execution.
24 config INIT_SP_RELATIVE
25 bool "Specify the early stack pointer relative to the .bss section"
27 U-Boot typically uses a hard-coded value for the stack pointer
28 before relocation. Enable this option to instead calculate the
29 initial SP at run-time. This is useful to avoid hard-coding addresses
30 into U-Boot, so that it can be loaded and executed at arbitrary
31 addresses and thus avoid using arbitrary addresses at runtime.
33 If this option is enabled, the early stack pointer is set to
34 &_bss_start with a offset value added. The offset is specified by
35 SYS_INIT_SP_BSS_OFFSET.
37 config SYS_INIT_SP_BSS_OFFSET
38 int "Early stack offset from the .bss base address"
39 depends on INIT_SP_RELATIVE
42 This option's value is the offset added to &_bss_start in order to
43 calculate the stack pointer. This offset should be large enough so
44 that the early malloc region, global data (gd), and early stack usage
45 do not overlap any appended DTB.
47 config LINUX_KERNEL_IMAGE_HEADER
50 Place a Linux kernel image header at the start of the U-Boot binary.
51 The format of the header is described in the Linux kernel source at
52 Documentation/arm64/booting.txt. This feature is useful since the
53 image header reports the amount of memory (BSS and similar) that
54 U-Boot needs to use, but which isn't part of the binary.
56 if LINUX_KERNEL_IMAGE_HEADER
57 config LNX_KRNL_IMG_TEXT_OFFSET_BASE
60 The value subtracted from CONFIG_SYS_TEXT_BASE to calculate the
61 TEXT_OFFSET value written to the Linux kernel image header.
70 ARM GICV3 Interrupt translation service (ITS).
71 Basic support for programming locality specific peripheral
72 interrupts (LPI) configuration tables and enable LPI tables.
73 LPI configuration table can be used by u-boot or Linux.
74 ARM GICV3 has limitation, once the LPI table is enabled, LPI
75 configuration table can not be re-programmed, unless GICV3 reset.
79 default y if ARM64 && !POSITION_INDEPENDENT
81 config DMA_ADDR_T_64BIT
91 # Used for compatibility with asm files copied from the kernel
92 config ARM_ASM_UNIFIED
96 # Used for compatibility with asm files copied from the kernel
100 config SYS_ICACHE_OFF
101 bool "Do not enable icache"
104 Do not enable instruction cache in U-Boot.
106 config SPL_SYS_ICACHE_OFF
107 bool "Do not enable icache in SPL"
109 default SYS_ICACHE_OFF
111 Do not enable instruction cache in SPL.
113 config SYS_DCACHE_OFF
114 bool "Do not enable dcache"
117 Do not enable data cache in U-Boot.
119 config SPL_SYS_DCACHE_OFF
120 bool "Do not enable dcache in SPL"
122 default SYS_DCACHE_OFF
124 Do not enable data cache in SPL.
126 config SYS_ARM_CACHE_CP15
127 bool "CP15 based cache enabling support"
129 Select this if your processor suports enabling caches by using
133 bool "MMU-based Paged Memory Management Support"
134 select SYS_ARM_CACHE_CP15
136 Select if you want MMU-based virtualised addressing space
137 support via paged memory management.
140 bool 'Use the ARM v7 PMSA Compliant MPU'
142 Some ARM systems without an MMU have instead a Memory Protection
143 Unit (MPU) that defines the type and permissions for regions of
145 If your CPU has an MPU then you should choose 'y' here unless you
146 know that you do not want to use the MPU.
148 # If set, the workarounds for these ARM errata are applied early during U-Boot
149 # startup. Note that in general these options force the workarounds to be
150 # applied; no CPU-type/version detection exists, unlike the similar options in
151 # the Linux kernel. Do not set these options unless they apply! Also note that
152 # the following can be machine-specific errata. These do have ability to
153 # provide rudimentary version and machine-specific checks, but expect no
155 # CONFIG_ARM_ERRATA_430973
156 # CONFIG_ARM_ERRATA_454179
157 # CONFIG_ARM_ERRATA_621766
158 # CONFIG_ARM_ERRATA_798870
159 # CONFIG_ARM_ERRATA_801819
160 # CONFIG_ARM_CORTEX_A8_CVE_2017_5715
161 # CONFIG_ARM_CORTEX_A15_CVE_2017_5715
163 config ARM_ERRATA_430973
166 config ARM_ERRATA_454179
169 config ARM_ERRATA_621766
172 config ARM_ERRATA_716044
175 config ARM_ERRATA_725233
178 config ARM_ERRATA_742230
181 config ARM_ERRATA_743622
184 config ARM_ERRATA_751472
187 config ARM_ERRATA_761320
190 config ARM_ERRATA_773022
193 config ARM_ERRATA_774769
196 config ARM_ERRATA_794072
199 config ARM_ERRATA_798870
202 config ARM_ERRATA_801819
205 config ARM_ERRATA_826974
208 config ARM_ERRATA_828024
211 config ARM_ERRATA_829520
214 config ARM_ERRATA_833069
217 config ARM_ERRATA_833471
220 config ARM_ERRATA_845369
223 config ARM_ERRATA_852421
226 config ARM_ERRATA_852423
229 config ARM_ERRATA_855873
232 config ARM_CORTEX_A8_CVE_2017_5715
235 config ARM_CORTEX_A15_CVE_2017_5715
240 select SYS_CACHE_SHIFT_5
245 select SYS_CACHE_SHIFT_5
250 select SYS_CACHE_SHIFT_5
255 select SYS_CACHE_SHIFT_5
260 select SYS_CACHE_SHIFT_5
266 select SYS_CACHE_SHIFT_5
273 select SYS_CACHE_SHIFT_6
280 select SYS_CACHE_SHIFT_5
281 select SYS_THUMB_BUILD
287 select SYS_ARM_CACHE_CP15
289 select SYS_CACHE_SHIFT_6
293 select SYS_CACHE_SHIFT_5
298 select SYS_CACHE_SHIFT_5
302 default "arm720t" if CPU_ARM720T
303 default "arm920t" if CPU_ARM920T
304 default "arm926ejs" if CPU_ARM926EJS
305 default "arm946es" if CPU_ARM946ES
306 default "arm1136" if CPU_ARM1136
307 default "arm1176" if CPU_ARM1176
308 default "armv7" if CPU_V7A
309 default "armv7" if CPU_V7R
310 default "armv7m" if CPU_V7M
311 default "pxa" if CPU_PXA
312 default "sa1100" if CPU_SA1100
313 default "armv8" if ARM64
317 default 4 if CPU_ARM720T
318 default 4 if CPU_ARM920T
319 default 5 if CPU_ARM926EJS
320 default 5 if CPU_ARM946ES
321 default 6 if CPU_ARM1136
322 default 6 if CPU_ARM1176
327 default 4 if CPU_SA1100
330 config SYS_CACHE_SHIFT_5
333 config SYS_CACHE_SHIFT_6
336 config SYS_CACHE_SHIFT_7
339 config SYS_CACHELINE_SIZE
341 default 128 if SYS_CACHE_SHIFT_7
342 default 64 if SYS_CACHE_SHIFT_6
343 default 32 if SYS_CACHE_SHIFT_5
346 prompt "Select the ARM data write cache policy"
347 default SYS_ARM_CACHE_WRITETHROUGH if TARGET_BCMCYGNUS || \
348 TARGET_BCMNSP || CPU_PXA || RZA1
349 default SYS_ARM_CACHE_WRITEBACK
351 config SYS_ARM_CACHE_WRITEBACK
352 bool "Write-back (WB)"
354 A write updates the cache only and marks the cache line as dirty.
355 External memory is updated only when the line is evicted or explicitly
358 config SYS_ARM_CACHE_WRITETHROUGH
359 bool "Write-through (WT)"
361 A write updates both the cache and the external memory system.
362 This does not mark the cache line as dirty.
364 config SYS_ARM_CACHE_WRITEALLOC
365 bool "Write allocation (WA)"
367 A cache line is allocated on a write miss. This means that executing a
368 store instruction on the processor might cause a burst read to occur.
369 There is a linefill to obtain the data for the cache line, before the
374 bool "Enable ARCH_CPU_INIT"
376 Some architectures require a call to arch_cpu_init().
377 Say Y here to enable it
379 config SYS_ARCH_TIMER
380 bool "ARM Generic Timer support"
381 depends on CPU_V7A || ARM64
384 The ARM Generic Timer (aka arch-timer) provides an architected
385 interface to a timer source on an SoC.
386 It is mandatory for ARMv8 implementation and widely available
390 bool "Support for ARM SMC Calling Convention (SMCCC)"
391 depends on CPU_V7A || ARM64
394 Say Y here if you want to enable ARM SMC Calling Convention.
395 This should be enabled if U-Boot needs to communicate with system
396 firmware (for example, PSCI) according to SMCCC.
399 bool "support boot from semihosting"
401 In emulated environments, semihosting is a way for
402 the hosted environment to call out to the emulator to
403 retrieve files from the host machine.
405 config SYS_THUMB_BUILD
406 bool "Build U-Boot using the Thumb instruction set"
409 Use this flag to build U-Boot using the Thumb instruction set for
410 ARM architectures. Thumb instruction set provides better code
411 density. For ARM architectures that support Thumb2 this flag will
412 result in Thumb2 code generated by GCC.
414 config SPL_SYS_THUMB_BUILD
415 bool "Build SPL using the Thumb instruction set"
416 default y if SYS_THUMB_BUILD
417 depends on !ARM64 && SPL
419 Use this flag to build SPL using the Thumb instruction set for
420 ARM architectures. Thumb instruction set provides better code
421 density. For ARM architectures that support Thumb2 this flag will
422 result in Thumb2 code generated by GCC.
424 config TPL_SYS_THUMB_BUILD
425 bool "Build TPL using the Thumb instruction set"
426 default y if SYS_THUMB_BUILD
427 depends on TPL && !ARM64
429 Use this flag to build TPL using the Thumb instruction set for
430 ARM architectures. Thumb instruction set provides better code
431 density. For ARM architectures that support Thumb2 this flag will
432 result in Thumb2 code generated by GCC.
435 config SYS_L2CACHE_OFF
438 If SoC does not support L2CACHE or one does not want to enable
439 L2CACHE, choose this option.
441 config ENABLE_ARM_SOC_BOOT0_HOOK
442 bool "prepare BOOT0 header"
444 If the SoC's BOOT0 requires a header area filled with (magic)
445 values, then choose this option, and create a file included as
446 <asm/arch/boot0.h> which contains the required assembler code.
448 config ARM_CORTEX_CPU_IS_UP
452 config USE_ARCH_MEMCPY
453 bool "Use an assembly optimized implementation of memcpy"
457 Enable the generation of an optimized version of memcpy.
458 Such an implementation may be faster under some conditions
459 but may increase the binary size.
461 config SPL_USE_ARCH_MEMCPY
462 bool "Use an assembly optimized implementation of memcpy for SPL"
463 default y if USE_ARCH_MEMCPY
464 depends on !ARM64 && SPL
466 Enable the generation of an optimized version of memcpy.
467 Such an implementation may be faster under some conditions
468 but may increase the binary size.
470 config TPL_USE_ARCH_MEMCPY
471 bool "Use an assembly optimized implementation of memcpy for TPL"
472 default y if USE_ARCH_MEMCPY
473 depends on !ARM64 && TPL
475 Enable the generation of an optimized version of memcpy.
476 Such an implementation may be faster under some conditions
477 but may increase the binary size.
479 config USE_ARCH_MEMSET
480 bool "Use an assembly optimized implementation of memset"
484 Enable the generation of an optimized version of memset.
485 Such an implementation may be faster under some conditions
486 but may increase the binary size.
488 config SPL_USE_ARCH_MEMSET
489 bool "Use an assembly optimized implementation of memset for SPL"
490 default y if USE_ARCH_MEMSET
491 depends on !ARM64 && SPL
493 Enable the generation of an optimized version of memset.
494 Such an implementation may be faster under some conditions
495 but may increase the binary size.
497 config TPL_USE_ARCH_MEMSET
498 bool "Use an assembly optimized implementation of memset for TPL"
499 default y if USE_ARCH_MEMSET
500 depends on !ARM64 && TPL
502 Enable the generation of an optimized version of memset.
503 Such an implementation may be faster under some conditions
504 but may increase the binary size.
506 config ARM64_SUPPORT_AARCH32
507 bool "ARM64 system support AArch32 execution state"
509 default y if !TARGET_THUNDERX_88XX
511 This ARM64 system supports AArch32 execution state.
514 prompt "Target select"
519 select SPL_BOARD_INIT if SPL && !TARGET_SMARTWEB
520 select SPL_SEPARATE_BSS if SPL
522 config TARGET_EDB93XX
523 bool "Support edb93xx"
527 config TARGET_ASPENITE
528 bool "Support aspenite"
532 bool "Support gplugd"
538 select SPL_DM_SPI if SPL
541 Support for TI's DaVinci platform.
544 bool "Marvell Kirkwood"
545 select ARCH_MISC_INIT
546 select BOARD_EARLY_INIT_F
550 bool "Marvell MVEBU family (Armada XP/375/38x/3700/7K/8K)"
556 select SPL_DM_SPI if SPL
557 select SPL_DM_SPI_FLASH if SPL
572 config TARGET_SPEAR300
573 bool "Support spear300"
574 select BOARD_EARLY_INIT_F
579 config TARGET_SPEAR310
580 bool "Support spear310"
581 select BOARD_EARLY_INIT_F
586 config TARGET_SPEAR320
587 bool "Support spear320"
588 select BOARD_EARLY_INIT_F
593 config TARGET_SPEAR600
594 bool "Support spear600"
595 select BOARD_EARLY_INIT_F
600 config TARGET_STV0991
601 bool "Support stv0991"
614 select BOARD_LATE_INIT
623 config TARGET_MX35PDK
624 bool "Support mx35pdk"
625 select BOARD_LATE_INIT
629 bool "Broadcom BCM283X family"
635 select SERIAL_SEARCH_ALL
640 bool "Broadcom BCM63158 family"
646 bool "Broadcom BCM68360 family"
652 bool "Broadcom BCM6858 family"
657 config TARGET_VEXPRESS_CA15_TC2
658 bool "Support vexpress_ca15_tc2"
660 select CPU_V7_HAS_NONSEC
661 select CPU_V7_HAS_VIRT
665 bool "Broadcom BCM7XXX family"
669 select OF_PRIOR_STAGE
672 This enables support for Broadcom ARM-based set-top box
673 chipsets, including the 7445 family of chips.
675 config TARGET_VEXPRESS_CA5X2
676 bool "Support vexpress_ca5x2"
680 config TARGET_VEXPRESS_CA9X4
681 bool "Support vexpress_ca9x4"
685 config TARGET_BCM23550_W1D
686 bool "Support bcm23550_w1d"
691 config TARGET_BCM28155_AP
692 bool "Support bcm28155_ap"
697 config TARGET_BCMCYGNUS
698 bool "Support bcmcygnus"
701 imply BCM_SF2_ETH_GMAC
709 bool "Support bcmnsp"
713 bool "Support Broadcom Northstar2"
716 Support for Broadcom Northstar 2 SoCs. NS2 is a quad-core 64-bit
717 ARMv8 Cortex-A57 processors targeting a broad range of networking
721 bool "Support Broadcom NS3"
723 select BOARD_LATE_INIT
725 Support for Broadcom Northstar 3 SoCs. NS3 is a octo-core 64-bit
726 ARMv8 Cortex-A72 processors targeting a broad range of networking
730 bool "Samsung EXYNOS"
739 imply SYS_THUMB_BUILD
744 bool "Samsung S5PC1XX"
753 bool "Calxeda Highbank"
757 config ARCH_INTEGRATOR
758 bool "ARM Ltd. Integrator family"
765 bool "Qualcomm IPQ40xx SoCs"
783 select SYS_ARCH_TIMER
784 select SYS_THUMB_BUILD
790 bool "Texas Instruments' K3 Architecture"
795 config ARCH_OMAP2PLUS
798 select SPL_BOARD_INIT if SPL
799 select SPL_STACK_R if SPL
805 imply DISTRO_DEFAULTS
808 Support for the Meson SoC family developed by Amlogic Inc.,
809 targeted at media players and tablet computers. We currently
810 support the S905 (GXBaby) 64-bit SoC.
817 select SPL_LIBCOMMON_SUPPORT if SPL
818 select SPL_LIBGENERIC_SUPPORT if SPL
819 select SPL_OF_CONTROL if SPL
822 Support for the MediaTek SoCs family developed by MediaTek Inc.
823 Please refer to doc/README.mediatek for more information.
826 bool "NXP LPC32xx platform"
836 bool "NXP i.MX8 platform"
840 select ENABLE_ARM_SOC_BOOT0_HOOK
843 bool "NXP i.MX8M platform"
850 bool "NXP i.MXRT platform"
858 bool "NXP i.MX23 family"
869 bool "NXP i.MX28 family"
875 bool "NXP i.MX31 family"
881 select ROM_UNIFIED_SECTIONS
883 imply SYS_THUMB_BUILD
887 select ARCH_MISC_INIT
889 select SYS_FSL_HAS_SEC if IMX_HAB
890 select SYS_FSL_SEC_COMPAT_4
891 select SYS_FSL_SEC_LE
892 imply BOARD_EARLY_INIT_F
894 imply SYS_THUMB_BUILD
899 select SYS_FSL_HAS_SEC
900 select SYS_FSL_SEC_COMPAT_4
901 select SYS_FSL_SEC_LE
903 imply SYS_THUMB_BUILD
907 default "arch/arm/mach-omap2/u-boot-spl.lds"
912 select BOARD_EARLY_INIT_F
917 bool "Nexell S5P4418/S5P6818 SoC"
918 select ENABLE_ARM_SOC_BOOT0_HOOK
922 bool "Actions Semi OWL SoCs"
930 select SYS_RELOC_GD_ENV_ADDR
934 bool "QEMU Virtual Platform"
935 select ARCH_SUPPORT_TFABOOT
945 bool "Renesas ARM SoCs"
946 select BOARD_EARLY_INIT_F if !RZA1
951 imply SYS_THUMB_BUILD
952 imply ARCH_MISC_INIT if DISPLAY_CPUINFO
954 config TARGET_S32V234EVB
955 bool "Support s32v234evb"
957 select SYS_FSL_ERRATUM_ESDHC111
959 config ARCH_SNAPDRAGON
960 bool "Qualcomm Snapdragon SoCs"
973 bool "Altera SOCFPGA family"
974 select ARCH_EARLY_INIT_R
975 select ARCH_MISC_INIT if !TARGET_SOCFPGA_ARRIA10
976 select ARM64 if TARGET_SOCFPGA_STRATIX10 || TARGET_SOCFPGA_AGILEX
977 select CPU_V7A if TARGET_SOCFPGA_GEN5 || TARGET_SOCFPGA_ARRIA10
980 select ENABLE_ARM_SOC_BOOT0_HOOK if TARGET_SOCFPGA_GEN5 || TARGET_SOCFPGA_ARRIA10
982 select SPL_DM_RESET if DM_RESET
984 select SPL_LIBCOMMON_SUPPORT
985 select SPL_LIBGENERIC_SUPPORT
986 select SPL_NAND_SUPPORT if SPL_NAND_DENALI
987 select SPL_OF_CONTROL
988 select SPL_SEPARATE_BSS if TARGET_SOCFPGA_STRATIX10 || TARGET_SOCFPGA_AGILEX
989 select SPL_SERIAL_SUPPORT
991 select SPL_WATCHDOG_SUPPORT
994 select SYS_THUMB_BUILD if TARGET_SOCFPGA_GEN5 || TARGET_SOCFPGA_ARRIA10
996 select SYSRESET_SOCFPGA if TARGET_SOCFPGA_GEN5 || TARGET_SOCFPGA_ARRIA10
997 select SYSRESET_SOCFPGA_S10 if TARGET_SOCFPGA_STRATIX10
1007 imply SPL_DM_SPI_FLASH
1008 imply SPL_LIBDISK_SUPPORT
1009 imply SPL_MMC_SUPPORT
1010 imply SYS_MMCSD_RAW_MODE_U_BOOT_USE_PARTITION
1011 imply SYS_MMCSD_RAW_MODE_U_BOOT_USE_PARTITION_TYPE
1012 imply SPL_SPI_FLASH_SUPPORT
1013 imply SPL_SPI_SUPPORT
1017 bool "Support sunxi (Allwinner) SoCs"
1020 select CMD_MMC if MMC
1021 select CMD_USB if DISTRO_DEFAULTS
1027 select DM_MMC if MMC
1028 select DM_SCSI if SCSI
1030 select DM_USB if DISTRO_DEFAULTS
1031 select OF_BOARD_SETUP
1034 select SPECIFY_CONSOLE_INDEX
1035 select SPL_STACK_R if SPL
1036 select SPL_SYS_MALLOC_SIMPLE if SPL
1037 select SPL_SYS_THUMB_BUILD if !ARM64
1040 select SYS_THUMB_BUILD if !ARM64
1041 select USB if DISTRO_DEFAULTS
1042 select USB_KEYBOARD if DISTRO_DEFAULTS
1043 select USB_STORAGE if DISTRO_DEFAULTS
1044 select SPL_USE_TINY_PRINTF
1046 select SYS_RELOC_GD_ENV_ADDR
1049 imply CMD_UBI if MTD_RAW_NAND
1050 imply DISTRO_DEFAULTS
1053 imply OF_LIBFDT_OVERLAY
1054 imply PRE_CONSOLE_BUFFER
1055 imply SPL_GPIO_SUPPORT
1056 imply SPL_LIBCOMMON_SUPPORT
1057 imply SPL_LIBGENERIC_SUPPORT
1058 imply SPL_MMC_SUPPORT if MMC
1059 imply SPL_POWER_SUPPORT
1060 imply SPL_SERIAL_SUPPORT
1064 bool "ST-Ericsson U8500 Series"
1068 select DM_MMC if MMC
1070 select DM_USB if USB
1074 imply ARM_PL180_MMCI
1076 imply NOMADIK_MTU_TIMER
1079 imply SYSRESET_SYSCON
1082 bool "Support Xilinx Versal Platform"
1086 select DM_ETH if NET
1087 select DM_MMC if MMC
1090 imply BOARD_LATE_INIT
1091 imply ENV_VARS_UBOOT_RUNTIME_CONFIG
1094 bool "Freescale Vybrid"
1096 select SYS_FSL_ERRATUM_ESDHC111
1101 bool "Xilinx Zynq based platform"
1106 select DM_ETH if NET
1107 select DM_MMC if MMC
1111 select DM_USB if USB
1114 select SPL_BOARD_INIT if SPL
1115 select SPL_CLK if SPL
1116 select SPL_DM if SPL
1117 select SPL_DM_SPI if SPL
1118 select SPL_DM_SPI_FLASH if SPL
1119 select SPL_OF_CONTROL if SPL
1120 select SPL_SEPARATE_BSS if SPL
1122 imply ARCH_EARLY_INIT_R
1123 imply BOARD_LATE_INIT
1127 imply ENV_VARS_UBOOT_RUNTIME_CONFIG
1130 config ARCH_ZYNQMP_R5
1131 bool "Xilinx ZynqMP R5 based platform"
1135 select DM_ETH if NET
1136 select DM_MMC if MMC
1143 bool "Xilinx ZynqMP based platform"
1147 select DM_ETH if NET
1149 select DM_MMC if MMC
1151 select DM_SPI if SPI
1152 select DM_SPI_FLASH if DM_SPI
1153 select DM_USB if USB
1156 select SPL_BOARD_INIT if SPL
1157 select SPL_CLK if SPL
1158 select SPL_DM if SPL
1159 select SPL_DM_SPI if SPI && SPL_DM
1160 select SPL_DM_SPI_FLASH if SPL_DM_SPI
1161 select SPL_DM_MAILBOX if SPL
1162 select SPL_FIRMWARE if SPL
1163 select SPL_SEPARATE_BSS if SPL
1166 imply BOARD_LATE_INIT
1168 imply ENV_VARS_UBOOT_RUNTIME_CONFIG
1175 imply DISTRO_DEFAULTS
1178 config TARGET_VEXPRESS64_AEMV8A
1179 bool "Support vexpress_aemv8a"
1183 config TARGET_VEXPRESS64_BASE_FVP
1184 bool "Support Versatile Express ARMv8a FVP BASE model"
1189 config TARGET_VEXPRESS64_JUNO
1190 bool "Support Versatile Express Juno Development Platform"
1205 config TARGET_TOTAL_COMPUTE
1206 bool "Support Total Compute Platform"
1214 config TARGET_LS2080A_EMU
1215 bool "Support ls2080a_emu"
1218 select ARMV8_MULTIENTRY
1219 select FSL_DDR_SYNC_REFRESH
1221 Support for Freescale LS2080A_EMU platform.
1222 The LS2080A Development System (EMULATOR) is a pre-silicon
1223 development platform that supports the QorIQ LS2080A
1224 Layerscape Architecture processor.
1226 config TARGET_LS2080A_SIMU
1227 bool "Support ls2080a_simu"
1230 select ARMV8_MULTIENTRY
1231 select BOARD_LATE_INIT
1233 Support for Freescale LS2080A_SIMU platform.
1234 The LS2080A Development System (QDS) is a pre silicon
1235 development platform that supports the QorIQ LS2080A
1236 Layerscape Architecture processor.
1238 config TARGET_LS1088AQDS
1239 bool "Support ls1088aqds"
1242 select ARMV8_MULTIENTRY
1243 select ARCH_SUPPORT_TFABOOT
1244 select BOARD_LATE_INIT
1246 select FSL_DDR_INTERACTIVE if !SD_BOOT
1248 Support for NXP LS1088AQDS platform.
1249 The LS1088A Development System (QDS) is a high-performance
1250 development platform that supports the QorIQ LS1088A
1251 Layerscape Architecture processor.
1253 config TARGET_LS2080AQDS
1254 bool "Support ls2080aqds"
1257 select ARMV8_MULTIENTRY
1258 select ARCH_SUPPORT_TFABOOT
1259 select BOARD_LATE_INIT
1264 select FSL_DDR_INTERACTIVE if !SPL
1266 Support for Freescale LS2080AQDS platform.
1267 The LS2080A Development System (QDS) is a high-performance
1268 development platform that supports the QorIQ LS2080A
1269 Layerscape Architecture processor.
1271 config TARGET_LS2080ARDB
1272 bool "Support ls2080ardb"
1275 select ARMV8_MULTIENTRY
1276 select ARCH_SUPPORT_TFABOOT
1277 select BOARD_LATE_INIT
1280 select FSL_DDR_INTERACTIVE if !SPL
1284 Support for Freescale LS2080ARDB platform.
1285 The LS2080A Reference design board (RDB) is a high-performance
1286 development platform that supports the QorIQ LS2080A
1287 Layerscape Architecture processor.
1289 config TARGET_LS2081ARDB
1290 bool "Support ls2081ardb"
1293 select ARMV8_MULTIENTRY
1294 select BOARD_LATE_INIT
1297 Support for Freescale LS2081ARDB platform.
1298 The LS2081A Reference design board (RDB) is a high-performance
1299 development platform that supports the QorIQ LS2081A/LS2041A
1300 Layerscape Architecture processor.
1302 config TARGET_LX2160ARDB
1303 bool "Support lx2160ardb"
1306 select ARMV8_MULTIENTRY
1307 select ARCH_SUPPORT_TFABOOT
1308 select BOARD_LATE_INIT
1310 Support for NXP LX2160ARDB platform.
1311 The lx2160ardb (LX2160A Reference design board (RDB)
1312 is a high-performance development platform that supports the
1313 QorIQ LX2160A/LX2120A/LX2080A Layerscape Architecture processor.
1315 config TARGET_LX2160AQDS
1316 bool "Support lx2160aqds"
1319 select ARMV8_MULTIENTRY
1320 select ARCH_SUPPORT_TFABOOT
1321 select BOARD_LATE_INIT
1323 Support for NXP LX2160AQDS platform.
1324 The lx2160aqds (LX2160A QorIQ Development System (QDS)
1325 is a high-performance development platform that supports the
1326 QorIQ LX2160A/LX2120A/LX2080A Layerscape Architecture processor.
1329 bool "Support HiKey 96boards Consumer Edition Platform"
1336 select SPECIFY_CONSOLE_INDEX
1339 Support for HiKey 96boards platform. It features a HI6220
1340 SoC, with 8xA53 CPU, mali450 gpu, and 1GB RAM.
1342 config TARGET_HIKEY960
1343 bool "Support HiKey960 96boards Consumer Edition Platform"
1351 Support for HiKey960 96boards platform. It features a HI3660
1352 SoC, with 4xA73 CPU, 4xA53 CPU, MALI-G71 GPU, and 3GB RAM.
1354 config TARGET_POPLAR
1355 bool "Support Poplar 96boards Enterprise Edition Platform"
1364 Support for Poplar 96boards EE platform. It features a HI3798cv200
1365 SoC, with 4xA53 CPU, 1GB RAM and the high performance Mali T720 GPU
1366 making it capable of running any commercial set-top solution based on
1369 config TARGET_LS1012AQDS
1370 bool "Support ls1012aqds"
1373 select ARCH_SUPPORT_TFABOOT
1374 select BOARD_LATE_INIT
1376 Support for Freescale LS1012AQDS platform.
1377 The LS1012A Development System (QDS) is a high-performance
1378 development platform that supports the QorIQ LS1012A
1379 Layerscape Architecture processor.
1381 config TARGET_LS1012ARDB
1382 bool "Support ls1012ardb"
1385 select ARCH_SUPPORT_TFABOOT
1386 select BOARD_LATE_INIT
1390 Support for Freescale LS1012ARDB platform.
1391 The LS1012A Reference design board (RDB) is a high-performance
1392 development platform that supports the QorIQ LS1012A
1393 Layerscape Architecture processor.
1395 config TARGET_LS1012A2G5RDB
1396 bool "Support ls1012a2g5rdb"
1399 select ARCH_SUPPORT_TFABOOT
1400 select BOARD_LATE_INIT
1403 Support for Freescale LS1012A2G5RDB platform.
1404 The LS1012A 2G5 Reference design board (RDB) is a high-performance
1405 development platform that supports the QorIQ LS1012A
1406 Layerscape Architecture processor.
1408 config TARGET_LS1012AFRWY
1409 bool "Support ls1012afrwy"
1412 select ARCH_SUPPORT_TFABOOT
1413 select BOARD_LATE_INIT
1417 Support for Freescale LS1012AFRWY platform.
1418 The LS1012A FRWY board (FRWY) is a high-performance
1419 development platform that supports the QorIQ LS1012A
1420 Layerscape Architecture processor.
1422 config TARGET_LS1012AFRDM
1423 bool "Support ls1012afrdm"
1426 select ARCH_SUPPORT_TFABOOT
1428 Support for Freescale LS1012AFRDM platform.
1429 The LS1012A Freedom board (FRDM) is a high-performance
1430 development platform that supports the QorIQ LS1012A
1431 Layerscape Architecture processor.
1433 config TARGET_LS1028AQDS
1434 bool "Support ls1028aqds"
1437 select ARMV8_MULTIENTRY
1438 select ARCH_SUPPORT_TFABOOT
1439 select BOARD_LATE_INIT
1441 Support for Freescale LS1028AQDS platform
1442 The LS1028A Development System (QDS) is a high-performance
1443 development platform that supports the QorIQ LS1028A
1444 Layerscape Architecture processor.
1446 config TARGET_LS1028ARDB
1447 bool "Support ls1028ardb"
1450 select ARMV8_MULTIENTRY
1451 select ARCH_SUPPORT_TFABOOT
1452 select BOARD_LATE_INIT
1454 Support for Freescale LS1028ARDB platform
1455 The LS1028A Development System (RDB) is a high-performance
1456 development platform that supports the QorIQ LS1028A
1457 Layerscape Architecture processor.
1459 config TARGET_LS1088ARDB
1460 bool "Support ls1088ardb"
1463 select ARMV8_MULTIENTRY
1464 select ARCH_SUPPORT_TFABOOT
1465 select BOARD_LATE_INIT
1467 select FSL_DDR_INTERACTIVE if !SD_BOOT
1469 Support for NXP LS1088ARDB platform.
1470 The LS1088A Reference design board (RDB) is a high-performance
1471 development platform that supports the QorIQ LS1088A
1472 Layerscape Architecture processor.
1474 config TARGET_LS1021AQDS
1475 bool "Support ls1021aqds"
1477 select ARCH_SUPPORT_PSCI
1478 select BOARD_EARLY_INIT_F
1479 select BOARD_LATE_INIT
1481 select CPU_V7_HAS_NONSEC
1482 select CPU_V7_HAS_VIRT
1483 select LS1_DEEP_SLEEP
1486 select FSL_DDR_INTERACTIVE
1487 select DM_SPI_FLASH if FSL_DSPI || FSL_QSPI
1488 select SPI_FLASH_DATAFLASH if FSL_DSPI || FSL_QSPI
1491 config TARGET_LS1021ATWR
1492 bool "Support ls1021atwr"
1494 select ARCH_SUPPORT_PSCI
1495 select BOARD_EARLY_INIT_F
1496 select BOARD_LATE_INIT
1498 select CPU_V7_HAS_NONSEC
1499 select CPU_V7_HAS_VIRT
1500 select LS1_DEEP_SLEEP
1502 select DM_SPI_FLASH if FSL_DSPI || FSL_QSPI
1505 config TARGET_LS1021ATSN
1506 bool "Support ls1021atsn"
1508 select ARCH_SUPPORT_PSCI
1509 select BOARD_EARLY_INIT_F
1510 select BOARD_LATE_INIT
1512 select CPU_V7_HAS_NONSEC
1513 select CPU_V7_HAS_VIRT
1514 select LS1_DEEP_SLEEP
1518 config TARGET_LS1021AIOT
1519 bool "Support ls1021aiot"
1521 select ARCH_SUPPORT_PSCI
1522 select BOARD_LATE_INIT
1524 select CPU_V7_HAS_NONSEC
1525 select CPU_V7_HAS_VIRT
1527 select DM_SPI_FLASH if FSL_DSPI || FSL_QSPI
1530 Support for Freescale LS1021AIOT platform.
1531 The LS1021A Freescale board (IOT) is a high-performance
1532 development platform that supports the QorIQ LS1021A
1533 Layerscape Architecture processor.
1535 config TARGET_LS1043AQDS
1536 bool "Support ls1043aqds"
1539 select ARMV8_MULTIENTRY
1540 select ARCH_SUPPORT_TFABOOT
1541 select BOARD_EARLY_INIT_F
1542 select BOARD_LATE_INIT
1544 select FSL_DDR_INTERACTIVE if !SPL
1545 select FSL_DSPI if !SPL_NO_DSPI
1546 select DM_SPI_FLASH if FSL_DSPI
1550 Support for Freescale LS1043AQDS platform.
1552 config TARGET_LS1043ARDB
1553 bool "Support ls1043ardb"
1556 select ARMV8_MULTIENTRY
1557 select ARCH_SUPPORT_TFABOOT
1558 select BOARD_EARLY_INIT_F
1559 select BOARD_LATE_INIT
1561 select FSL_DSPI if !SPL_NO_DSPI
1562 select DM_SPI_FLASH if FSL_DSPI
1564 Support for Freescale LS1043ARDB platform.
1566 config TARGET_LS1046AQDS
1567 bool "Support ls1046aqds"
1570 select ARMV8_MULTIENTRY
1571 select ARCH_SUPPORT_TFABOOT
1572 select BOARD_EARLY_INIT_F
1573 select BOARD_LATE_INIT
1574 select DM_SPI_FLASH if DM_SPI
1576 select FSL_DDR_BIST if !SPL
1577 select FSL_DDR_INTERACTIVE if !SPL
1578 select FSL_DDR_INTERACTIVE if !SPL
1581 Support for Freescale LS1046AQDS platform.
1582 The LS1046A Development System (QDS) is a high-performance
1583 development platform that supports the QorIQ LS1046A
1584 Layerscape Architecture processor.
1586 config TARGET_LS1046ARDB
1587 bool "Support ls1046ardb"
1590 select ARMV8_MULTIENTRY
1591 select ARCH_SUPPORT_TFABOOT
1592 select BOARD_EARLY_INIT_F
1593 select BOARD_LATE_INIT
1594 select DM_SPI_FLASH if DM_SPI
1595 select POWER_MC34VR500
1598 select FSL_DDR_INTERACTIVE if !SPL
1601 Support for Freescale LS1046ARDB platform.
1602 The LS1046A Reference Design Board (RDB) is a high-performance
1603 development platform that supports the QorIQ LS1046A
1604 Layerscape Architecture processor.
1606 config TARGET_LS1046AFRWY
1607 bool "Support ls1046afrwy"
1610 select ARMV8_MULTIENTRY
1611 select ARCH_SUPPORT_TFABOOT
1612 select BOARD_EARLY_INIT_F
1613 select BOARD_LATE_INIT
1614 select DM_SPI_FLASH if DM_SPI
1617 Support for Freescale LS1046AFRWY platform.
1618 The LS1046A Freeway Board (FRWY) is a high-performance
1619 development platform that supports the QorIQ LS1046A
1620 Layerscape Architecture processor.
1622 config TARGET_COLIBRI_PXA270
1623 bool "Support colibri_pxa270"
1626 config ARCH_UNIPHIER
1627 bool "Socionext UniPhier SoCs"
1628 select BOARD_LATE_INIT
1638 select OF_BOARD_SETUP
1642 select SPL_BOARD_INIT if SPL
1643 select SPL_DM if SPL
1644 select SPL_LIBCOMMON_SUPPORT if SPL
1645 select SPL_LIBGENERIC_SUPPORT if SPL
1646 select SPL_OF_CONTROL if SPL
1647 select SPL_PINCTRL if SPL
1650 imply DISTRO_DEFAULTS
1653 Support for UniPhier SoC family developed by Socionext Inc.
1654 (formerly, System LSI Business Division of Panasonic Corporation)
1657 bool "Support STMicroelectronics STM32 MCU with cortex M"
1664 bool "Support STMicrolectronics SoCs"
1673 Support for STMicroelectronics STiH407/10 SoC family.
1674 This SoC is used on Linaro 96Board STiH410-B2260
1677 bool "Support STMicroelectronics STM32MP Socs with cortex A"
1678 select ARCH_MISC_INIT
1679 select ARCH_SUPPORT_TFABOOT
1680 select BOARD_LATE_INIT
1689 select OF_SYSTEM_SETUP
1695 select SYS_THUMB_BUILD
1699 imply OF_LIBFDT_OVERLAY
1700 imply ENV_VARS_UBOOT_RUNTIME_CONFIG
1703 Support for STM32MP SoC family developed by STMicroelectronics,
1704 MPUs based on ARM cortex A core
1705 U-BOOT is running in DDR, loaded by the First Stage BootLoader (FSBL).
1706 FSBL can be TF-A: Trusted Firmware for Cortex A, for trusted boot
1708 SPL is the unsecure FSBL for the basic boot chain.
1710 config ARCH_ROCKCHIP
1711 bool "Support Rockchip SoCs"
1713 select BINMAN if !ARM64
1723 select DM_USB if USB
1724 select ENABLE_ARM_SOC_BOOT0_HOOK
1727 select SPL_DM if SPL
1728 select SPL_DM_SPI if SPL
1729 select SPL_DM_SPI_FLASH if SPL
1731 select SYS_THUMB_BUILD if !ARM64
1734 imply DEBUG_UART_BOARD_INIT
1735 imply DISTRO_DEFAULTS
1737 imply SARADC_ROCKCHIP
1739 imply SPL_SYS_MALLOC_SIMPLE
1742 imply USB_FUNCTION_FASTBOOT
1744 config ARCH_OCTEONTX
1745 bool "Support OcteonTX SoCs"
1750 select BOARD_LATE_INIT
1751 select SYS_CACHE_SHIFT_7
1753 config ARCH_OCTEONTX2
1754 bool "Support OcteonTX2 SoCs"
1759 select BOARD_LATE_INIT
1760 select SYS_CACHE_SHIFT_7
1762 config TARGET_THUNDERX_88XX
1763 bool "Support ThunderX 88xx"
1767 select SYS_CACHE_SHIFT_7
1770 bool "Support Aspeed SoCs"
1775 config TARGET_DURIAN
1776 bool "Support Phytium Durian Platform"
1779 Support for durian platform.
1780 It has 2GB Sdram, uart and pcie.
1782 config TARGET_PRESIDIO_ASIC
1783 bool "Support Cortina Presidio ASIC Platform"
1786 config TARGET_XENGUEST_ARM64
1787 bool "Xen guest ARM64"
1791 select LINUX_KERNEL_IMAGE_HEADER
1796 config ARCH_SUPPORT_TFABOOT
1800 bool "Support for booting from TF-A"
1801 depends on ARCH_SUPPORT_TFABOOT
1804 Enabling this will make a U-Boot binary that is capable of being
1805 booted via TF-A (Trusted Firmware for Cortex-A).
1807 config TI_SECURE_DEVICE
1808 bool "HS Device Type Support"
1809 depends on ARCH_KEYSTONE || ARCH_OMAP2PLUS || ARCH_K3
1811 If a high secure (HS) device type is being used, this config
1812 must be set. This option impacts various aspects of the
1813 build system (to create signed boot images that can be
1814 authenticated) and the code. See the doc/README.ti-secure
1815 file for further details.
1817 if AM43XX || AM33XX || OMAP54XX || ARCH_KEYSTONE
1818 config ISW_ENTRY_ADDR
1819 hex "Address in memory or XIP address of bootloader entry point"
1820 default 0x402F4000 if AM43XX
1821 default 0x402F0400 if AM33XX
1822 default 0x40301350 if OMAP54XX
1824 After any reset, the boot ROM searches the boot media for a valid
1825 boot image. For non-XIP devices, the ROM then copies the image into
1826 internal memory. For all boot modes, after the ROM processes the
1827 boot image it eventually computes the entry point address depending
1828 on the device type (secure/non-secure), boot media (xip/non-xip) and
1832 source "arch/arm/mach-aspeed/Kconfig"
1834 source "arch/arm/mach-at91/Kconfig"
1836 source "arch/arm/mach-bcm283x/Kconfig"
1838 source "arch/arm/mach-bcmstb/Kconfig"
1840 source "arch/arm/mach-davinci/Kconfig"
1842 source "arch/arm/mach-exynos/Kconfig"
1844 source "arch/arm/mach-highbank/Kconfig"
1846 source "arch/arm/mach-integrator/Kconfig"
1848 source "arch/arm/mach-ipq40xx/Kconfig"
1850 source "arch/arm/mach-k3/Kconfig"
1852 source "arch/arm/mach-keystone/Kconfig"
1854 source "arch/arm/mach-kirkwood/Kconfig"
1856 source "arch/arm/mach-lpc32xx/Kconfig"
1858 source "arch/arm/mach-mvebu/Kconfig"
1860 source "arch/arm/mach-octeontx/Kconfig"
1862 source "arch/arm/mach-octeontx2/Kconfig"
1864 source "arch/arm/cpu/armv7/ls102xa/Kconfig"
1866 source "arch/arm/mach-imx/mx2/Kconfig"
1868 source "arch/arm/mach-imx/mx3/Kconfig"
1870 source "arch/arm/mach-imx/mx5/Kconfig"
1872 source "arch/arm/mach-imx/mx6/Kconfig"
1874 source "arch/arm/mach-imx/mx7/Kconfig"
1876 source "arch/arm/mach-imx/mx7ulp/Kconfig"
1878 source "arch/arm/mach-imx/imx8/Kconfig"
1880 source "arch/arm/mach-imx/imx8m/Kconfig"
1882 source "arch/arm/mach-imx/imxrt/Kconfig"
1884 source "arch/arm/mach-imx/mxs/Kconfig"
1886 source "arch/arm/mach-omap2/Kconfig"
1888 source "arch/arm/cpu/armv8/fsl-layerscape/Kconfig"
1890 source "arch/arm/mach-orion5x/Kconfig"
1892 source "arch/arm/mach-owl/Kconfig"
1894 source "arch/arm/mach-rmobile/Kconfig"
1896 source "arch/arm/mach-meson/Kconfig"
1898 source "arch/arm/mach-mediatek/Kconfig"
1900 source "arch/arm/mach-qemu/Kconfig"
1902 source "arch/arm/mach-rockchip/Kconfig"
1904 source "arch/arm/mach-s5pc1xx/Kconfig"
1906 source "arch/arm/mach-snapdragon/Kconfig"
1908 source "arch/arm/mach-socfpga/Kconfig"
1910 source "arch/arm/mach-sti/Kconfig"
1912 source "arch/arm/mach-stm32/Kconfig"
1914 source "arch/arm/mach-stm32mp/Kconfig"
1916 source "arch/arm/mach-sunxi/Kconfig"
1918 source "arch/arm/mach-tegra/Kconfig"
1920 source "arch/arm/mach-u8500/Kconfig"
1922 source "arch/arm/mach-uniphier/Kconfig"
1924 source "arch/arm/cpu/armv7/vf610/Kconfig"
1926 source "arch/arm/mach-zynq/Kconfig"
1928 source "arch/arm/mach-zynqmp/Kconfig"
1930 source "arch/arm/mach-versal/Kconfig"
1932 source "arch/arm/mach-zynqmp-r5/Kconfig"
1934 source "arch/arm/cpu/armv7/Kconfig"
1936 source "arch/arm/cpu/armv8/Kconfig"
1938 source "arch/arm/mach-imx/Kconfig"
1940 source "arch/arm/mach-nexell/Kconfig"
1942 source "board/armltd/total_compute/Kconfig"
1944 source "board/bosch/shc/Kconfig"
1945 source "board/bosch/guardian/Kconfig"
1946 source "board/CarMediaLab/flea3/Kconfig"
1947 source "board/Marvell/aspenite/Kconfig"
1948 source "board/Marvell/gplugd/Kconfig"
1949 source "board/Marvell/octeontx/Kconfig"
1950 source "board/Marvell/octeontx2/Kconfig"
1951 source "board/armadeus/apf27/Kconfig"
1952 source "board/armltd/vexpress/Kconfig"
1953 source "board/armltd/vexpress64/Kconfig"
1954 source "board/cortina/presidio-asic/Kconfig"
1955 source "board/broadcom/bcm23550_w1d/Kconfig"
1956 source "board/broadcom/bcm28155_ap/Kconfig"
1957 source "board/broadcom/bcm963158/Kconfig"
1958 source "board/broadcom/bcm968360bg/Kconfig"
1959 source "board/broadcom/bcm968580xref/Kconfig"
1960 source "board/broadcom/bcmcygnus/Kconfig"
1961 source "board/broadcom/bcmnsp/Kconfig"
1962 source "board/broadcom/bcmns2/Kconfig"
1963 source "board/broadcom/bcmns3/Kconfig"
1964 source "board/cavium/thunderx/Kconfig"
1965 source "board/cirrus/edb93xx/Kconfig"
1966 source "board/eets/pdu001/Kconfig"
1967 source "board/emulation/qemu-arm/Kconfig"
1968 source "board/freescale/ls2080a/Kconfig"
1969 source "board/freescale/ls2080aqds/Kconfig"
1970 source "board/freescale/ls2080ardb/Kconfig"
1971 source "board/freescale/ls1088a/Kconfig"
1972 source "board/freescale/ls1028a/Kconfig"
1973 source "board/freescale/ls1021aqds/Kconfig"
1974 source "board/freescale/ls1043aqds/Kconfig"
1975 source "board/freescale/ls1021atwr/Kconfig"
1976 source "board/freescale/ls1021atsn/Kconfig"
1977 source "board/freescale/ls1021aiot/Kconfig"
1978 source "board/freescale/ls1046aqds/Kconfig"
1979 source "board/freescale/ls1043ardb/Kconfig"
1980 source "board/freescale/ls1046ardb/Kconfig"
1981 source "board/freescale/ls1046afrwy/Kconfig"
1982 source "board/freescale/ls1012aqds/Kconfig"
1983 source "board/freescale/ls1012ardb/Kconfig"
1984 source "board/freescale/ls1012afrdm/Kconfig"
1985 source "board/freescale/lx2160a/Kconfig"
1986 source "board/freescale/mx35pdk/Kconfig"
1987 source "board/freescale/s32v234evb/Kconfig"
1988 source "board/grinn/chiliboard/Kconfig"
1989 source "board/hisilicon/hikey/Kconfig"
1990 source "board/hisilicon/hikey960/Kconfig"
1991 source "board/hisilicon/poplar/Kconfig"
1992 source "board/isee/igep003x/Kconfig"
1993 source "board/myir/mys_6ulx/Kconfig"
1994 source "board/spear/spear300/Kconfig"
1995 source "board/spear/spear310/Kconfig"
1996 source "board/spear/spear320/Kconfig"
1997 source "board/spear/spear600/Kconfig"
1998 source "board/spear/x600/Kconfig"
1999 source "board/st/stv0991/Kconfig"
2000 source "board/tcl/sl50/Kconfig"
2001 source "board/toradex/colibri_pxa270/Kconfig"
2002 source "board/variscite/dart_6ul/Kconfig"
2003 source "board/vscom/baltos/Kconfig"
2004 source "board/phytium/durian/Kconfig"
2005 source "board/xen/xenguest_arm64/Kconfig"
2007 source "arch/arm/Kconfig.debug"
2012 default "arch/arm/cpu/arm926ejs/mxs/u-boot-spl.lds" if (ARCH_MX23 || ARCH_MX28) && !SPL_FRAMEWORK
2013 default "arch/arm/cpu/arm1136/u-boot-spl.lds" if CPU_ARM1136
2014 default "arch/arm/cpu/armv8/u-boot-spl.lds" if ARM64