2 # (C) Copyright 2000 - 2013
3 # Wolfgang Denk, DENX Software Engineering, wd@denx.de.
5 # SPDX-License-Identifier: GPL-2.0+
11 This directory contains the source code for U-Boot, a boot loader for
12 Embedded boards based on PowerPC, ARM, MIPS and several other
13 processors, which can be installed in a boot ROM and used to
14 initialize and test the hardware or to download and run application
17 The development of U-Boot is closely related to Linux: some parts of
18 the source code originate in the Linux source tree, we have some
19 header files in common, and special provision has been made to
20 support booting of Linux images.
22 Some attention has been paid to make this software easily
23 configurable and extendable. For instance, all monitor commands are
24 implemented with the same call interface, so that it's very easy to
25 add new commands. Also, instead of permanently adding rarely used
26 code (for instance hardware test utilities) to the monitor, you can
27 load and run it dynamically.
33 In general, all boards for which a configuration option exists in the
34 Makefile have been tested to some extent and can be considered
35 "working". In fact, many of them are used in production systems.
37 In case of problems see the CHANGELOG and CREDITS files to find out
38 who contributed the specific port. The boards.cfg file lists board
41 Note: There is no CHANGELOG file in the actual U-Boot source tree;
42 it can be created dynamically from the Git log using:
50 In case you have questions about, problems with or contributions for
51 U-Boot you should send a message to the U-Boot mailing list at
52 <u-boot@lists.denx.de>. There is also an archive of previous traffic
53 on the mailing list - please search the archive before asking FAQ's.
54 Please see http://lists.denx.de/pipermail/u-boot and
55 http://dir.gmane.org/gmane.comp.boot-loaders.u-boot
58 Where to get source code:
59 =========================
61 The U-Boot source code is maintained in the git repository at
62 git://www.denx.de/git/u-boot.git ; you can browse it online at
63 http://www.denx.de/cgi-bin/gitweb.cgi?p=u-boot.git;a=summary
65 The "snapshot" links on this page allow you to download tarballs of
66 any version you might be interested in. Official releases are also
67 available for FTP download from the ftp://ftp.denx.de/pub/u-boot/
70 Pre-built (and tested) images are available from
71 ftp://ftp.denx.de/pub/u-boot/images/
77 - start from 8xxrom sources
78 - create PPCBoot project (http://sourceforge.net/projects/ppcboot)
80 - make it easier to add custom boards
81 - make it possible to add other [PowerPC] CPUs
82 - extend functions, especially:
83 * Provide extended interface to Linux boot loader
86 * PCMCIA / CompactFlash / ATA disk / SCSI ... boot
87 - create ARMBoot project (http://sourceforge.net/projects/armboot)
88 - add other CPU families (starting with ARM)
89 - create U-Boot project (http://sourceforge.net/projects/u-boot)
90 - current project page: see http://www.denx.de/wiki/U-Boot
96 The "official" name of this project is "Das U-Boot". The spelling
97 "U-Boot" shall be used in all written text (documentation, comments
98 in source files etc.). Example:
100 This is the README file for the U-Boot project.
102 File names etc. shall be based on the string "u-boot". Examples:
104 include/asm-ppc/u-boot.h
106 #include <asm/u-boot.h>
108 Variable names, preprocessor constants etc. shall be either based on
109 the string "u_boot" or on "U_BOOT". Example:
111 U_BOOT_VERSION u_boot_logo
112 IH_OS_U_BOOT u_boot_hush_start
118 Starting with the release in October 2008, the names of the releases
119 were changed from numerical release numbers without deeper meaning
120 into a time stamp based numbering. Regular releases are identified by
121 names consisting of the calendar year and month of the release date.
122 Additional fields (if present) indicate release candidates or bug fix
123 releases in "stable" maintenance trees.
126 U-Boot v2009.11 - Release November 2009
127 U-Boot v2009.11.1 - Release 1 in version November 2009 stable tree
128 U-Boot v2010.09-rc1 - Release candiate 1 for September 2010 release
134 /arch Architecture specific files
135 /arc Files generic to ARC architecture
136 /cpu CPU specific files
137 /arc700 Files specific to ARC 700 CPUs
138 /lib Architecture specific library files
139 /arm Files generic to ARM architecture
140 /cpu CPU specific files
141 /arm720t Files specific to ARM 720 CPUs
142 /arm920t Files specific to ARM 920 CPUs
143 /at91 Files specific to Atmel AT91RM9200 CPU
144 /imx Files specific to Freescale MC9328 i.MX CPUs
145 /s3c24x0 Files specific to Samsung S3C24X0 CPUs
146 /arm926ejs Files specific to ARM 926 CPUs
147 /arm1136 Files specific to ARM 1136 CPUs
148 /pxa Files specific to Intel XScale PXA CPUs
149 /sa1100 Files specific to Intel StrongARM SA1100 CPUs
150 /lib Architecture specific library files
151 /avr32 Files generic to AVR32 architecture
152 /cpu CPU specific files
153 /lib Architecture specific library files
154 /blackfin Files generic to Analog Devices Blackfin architecture
155 /cpu CPU specific files
156 /lib Architecture specific library files
157 /m68k Files generic to m68k architecture
158 /cpu CPU specific files
159 /mcf52x2 Files specific to Freescale ColdFire MCF52x2 CPUs
160 /mcf5227x Files specific to Freescale ColdFire MCF5227x CPUs
161 /mcf532x Files specific to Freescale ColdFire MCF5329 CPUs
162 /mcf5445x Files specific to Freescale ColdFire MCF5445x CPUs
163 /mcf547x_8x Files specific to Freescale ColdFire MCF547x_8x CPUs
164 /lib Architecture specific library files
165 /microblaze Files generic to microblaze architecture
166 /cpu CPU specific files
167 /lib Architecture specific library files
168 /mips Files generic to MIPS architecture
169 /cpu CPU specific files
170 /mips32 Files specific to MIPS32 CPUs
171 /mips64 Files specific to MIPS64 CPUs
172 /lib Architecture specific library files
173 /nds32 Files generic to NDS32 architecture
174 /cpu CPU specific files
175 /n1213 Files specific to Andes Technology N1213 CPUs
176 /lib Architecture specific library files
177 /nios2 Files generic to Altera NIOS2 architecture
178 /cpu CPU specific files
179 /lib Architecture specific library files
180 /openrisc Files generic to OpenRISC architecture
181 /cpu CPU specific files
182 /lib Architecture specific library files
183 /powerpc Files generic to PowerPC architecture
184 /cpu CPU specific files
185 /74xx_7xx Files specific to Freescale MPC74xx and 7xx CPUs
186 /mpc5xx Files specific to Freescale MPC5xx CPUs
187 /mpc5xxx Files specific to Freescale MPC5xxx CPUs
188 /mpc8xx Files specific to Freescale MPC8xx CPUs
189 /mpc824x Files specific to Freescale MPC824x CPUs
190 /mpc8260 Files specific to Freescale MPC8260 CPUs
191 /mpc85xx Files specific to Freescale MPC85xx CPUs
192 /ppc4xx Files specific to AMCC PowerPC 4xx CPUs
193 /lib Architecture specific library files
194 /sh Files generic to SH architecture
195 /cpu CPU specific files
196 /sh2 Files specific to sh2 CPUs
197 /sh3 Files specific to sh3 CPUs
198 /sh4 Files specific to sh4 CPUs
199 /lib Architecture specific library files
200 /sparc Files generic to SPARC architecture
201 /cpu CPU specific files
202 /leon2 Files specific to Gaisler LEON2 SPARC CPU
203 /leon3 Files specific to Gaisler LEON3 SPARC CPU
204 /lib Architecture specific library files
205 /x86 Files generic to x86 architecture
206 /cpu CPU specific files
207 /lib Architecture specific library files
208 /api Machine/arch independent API for external apps
209 /board Board dependent files
210 /common Misc architecture independent functions
211 /disk Code for disk drive partition handling
212 /doc Documentation (don't expect too much)
213 /drivers Commonly used device drivers
214 /dts Contains Makefile for building internal U-Boot fdt.
215 /examples Example code for standalone applications, etc.
216 /fs Filesystem code (cramfs, ext2, jffs2, etc.)
217 /include Header Files
218 /lib Files generic to all architectures
219 /libfdt Library files to support flattened device trees
220 /lzma Library files to support LZMA decompression
221 /lzo Library files to support LZO decompression
223 /post Power On Self Test
224 /spl Secondary Program Loader framework
225 /tools Tools to build S-Record or U-Boot images, etc.
227 Software Configuration:
228 =======================
230 Configuration is usually done using C preprocessor defines; the
231 rationale behind that is to avoid dead code whenever possible.
233 There are two classes of configuration variables:
235 * Configuration _OPTIONS_:
236 These are selectable by the user and have names beginning with
239 * Configuration _SETTINGS_:
240 These depend on the hardware etc. and should not be meddled with if
241 you don't know what you're doing; they have names beginning with
244 Later we will add a configuration tool - probably similar to or even
245 identical to what's used for the Linux kernel. Right now, we have to
246 do the configuration by hand, which means creating some symbolic
247 links and editing some configuration files. We use the TQM8xxL boards
251 Selection of Processor Architecture and Board Type:
252 ---------------------------------------------------
254 For all supported boards there are ready-to-use default
255 configurations available; just type "make <board_name>_defconfig".
257 Example: For a TQM823L module type:
260 make TQM823L_defconfig
262 For the Cogent platform, you need to specify the CPU type as well;
263 e.g. "make cogent_mpc8xx_defconfig". And also configure the cogent
264 directory according to the instructions in cogent/README.
270 U-Boot can be built natively to run on a Linux host using the 'sandbox'
271 board. This allows feature development which is not board- or architecture-
272 specific to be undertaken on a native platform. The sandbox is also used to
273 run some of U-Boot's tests.
275 See board/sandbox/README.sandbox for more details.
278 Configuration Options:
279 ----------------------
281 Configuration depends on the combination of board and CPU type; all
282 such information is kept in a configuration file
283 "include/configs/<board_name>.h".
285 Example: For a TQM823L module, all configuration settings are in
286 "include/configs/TQM823L.h".
289 Many of the options are named exactly as the corresponding Linux
290 kernel configuration options. The intention is to make it easier to
291 build a config tool - later.
294 The following options need to be configured:
296 - CPU Type: Define exactly one, e.g. CONFIG_MPC85XX.
298 - Board Type: Define exactly one, e.g. CONFIG_MPC8540ADS.
300 - CPU Daughterboard Type: (if CONFIG_ATSTK1000 is defined)
301 Define exactly one, e.g. CONFIG_ATSTK1002
303 - CPU Module Type: (if CONFIG_COGENT is defined)
304 Define exactly one of
306 --- FIXME --- not tested yet:
307 CONFIG_CMA286_60, CONFIG_CMA286_21, CONFIG_CMA286_60P,
308 CONFIG_CMA287_23, CONFIG_CMA287_50
310 - Motherboard Type: (if CONFIG_COGENT is defined)
311 Define exactly one of
312 CONFIG_CMA101, CONFIG_CMA102
314 - Motherboard I/O Modules: (if CONFIG_COGENT is defined)
315 Define one or more of
318 - Motherboard Options: (if CONFIG_CMA101 or CONFIG_CMA102 are defined)
319 Define one or more of
320 CONFIG_LCD_HEARTBEAT - update a character position on
321 the LCD display every second with
324 - Marvell Family Member
325 CONFIG_SYS_MVFS - define it if you want to enable
326 multiple fs option at one time
327 for marvell soc family
329 - MPC824X Family Member (if CONFIG_MPC824X is defined)
330 Define exactly one of
331 CONFIG_MPC8240, CONFIG_MPC8245
333 - 8xx CPU Options: (if using an MPC8xx CPU)
334 CONFIG_8xx_GCLK_FREQ - deprecated: CPU clock if
335 get_gclk_freq() cannot work
336 e.g. if there is no 32KHz
337 reference PIT/RTC clock
338 CONFIG_8xx_OSCLK - PLL input clock (either EXTCLK
341 - 859/866/885 CPU options: (if using a MPC859 or MPC866 or MPC885 CPU):
342 CONFIG_SYS_8xx_CPUCLK_MIN
343 CONFIG_SYS_8xx_CPUCLK_MAX
344 CONFIG_8xx_CPUCLK_DEFAULT
345 See doc/README.MPC866
347 CONFIG_SYS_MEASURE_CPUCLK
349 Define this to measure the actual CPU clock instead
350 of relying on the correctness of the configured
351 values. Mostly useful for board bringup to make sure
352 the PLL is locked at the intended frequency. Note
353 that this requires a (stable) reference clock (32 kHz
354 RTC clock or CONFIG_SYS_8XX_XIN)
356 CONFIG_SYS_DELAYED_ICACHE
358 Define this option if you want to enable the
359 ICache only when Code runs from RAM.
364 Specifies that the core is a 64-bit PowerPC implementation (implements
365 the "64" category of the Power ISA). This is necessary for ePAPR
366 compliance, among other possible reasons.
368 CONFIG_SYS_FSL_TBCLK_DIV
370 Defines the core time base clock divider ratio compared to the
371 system clock. On most PQ3 devices this is 8, on newer QorIQ
372 devices it can be 16 or 32. The ratio varies from SoC to Soc.
374 CONFIG_SYS_FSL_PCIE_COMPAT
376 Defines the string to utilize when trying to match PCIe device
377 tree nodes for the given platform.
379 CONFIG_SYS_PPC_E500_DEBUG_TLB
381 Enables a temporary TLB entry to be used during boot to work
382 around limitations in e500v1 and e500v2 external debugger
383 support. This reduces the portions of the boot code where
384 breakpoints and single stepping do not work. The value of this
385 symbol should be set to the TLB1 entry to be used for this
388 CONFIG_SYS_FSL_ERRATUM_A004510
390 Enables a workaround for erratum A004510. If set,
391 then CONFIG_SYS_FSL_ERRATUM_A004510_SVR_REV and
392 CONFIG_SYS_FSL_CORENET_SNOOPVEC_COREONLY must be set.
394 CONFIG_SYS_FSL_ERRATUM_A004510_SVR_REV
395 CONFIG_SYS_FSL_ERRATUM_A004510_SVR_REV2 (optional)
397 Defines one or two SoC revisions (low 8 bits of SVR)
398 for which the A004510 workaround should be applied.
400 The rest of SVR is either not relevant to the decision
401 of whether the erratum is present (e.g. p2040 versus
402 p2041) or is implied by the build target, which controls
403 whether CONFIG_SYS_FSL_ERRATUM_A004510 is set.
405 See Freescale App Note 4493 for more information about
408 CONFIG_A003399_NOR_WORKAROUND
409 Enables a workaround for IFC erratum A003399. It is only
410 requred during NOR boot.
412 CONFIG_SYS_FSL_CORENET_SNOOPVEC_COREONLY
414 This is the value to write into CCSR offset 0x18600
415 according to the A004510 workaround.
417 CONFIG_SYS_FSL_DSP_DDR_ADDR
418 This value denotes start offset of DDR memory which is
419 connected exclusively to the DSP cores.
421 CONFIG_SYS_FSL_DSP_M2_RAM_ADDR
422 This value denotes start offset of M2 memory
423 which is directly connected to the DSP core.
425 CONFIG_SYS_FSL_DSP_M3_RAM_ADDR
426 This value denotes start offset of M3 memory which is directly
427 connected to the DSP core.
429 CONFIG_SYS_FSL_DSP_CCSRBAR_DEFAULT
430 This value denotes start offset of DSP CCSR space.
432 CONFIG_SYS_FSL_SINGLE_SOURCE_CLK
433 Single Source Clock is clocking mode present in some of FSL SoC's.
434 In this mode, a single differential clock is used to supply
435 clocks to the sysclock, ddrclock and usbclock.
437 CONFIG_SYS_CPC_REINIT_F
438 This CONFIG is defined when the CPC is configured as SRAM at the
439 time of U-boot entry and is required to be re-initialized.
442 Inidcates this SoC supports deep sleep feature. If deep sleep is
443 supported, core will start to execute uboot when wakes up.
445 - Generic CPU options:
446 CONFIG_SYS_GENERIC_GLOBAL_DATA
447 Defines global data is initialized in generic board board_init_f().
448 If this macro is defined, global data is created and cleared in
449 generic board board_init_f(). Without this macro, architecture/board
450 should initialize global data before calling board_init_f().
452 CONFIG_SYS_BIG_ENDIAN, CONFIG_SYS_LITTLE_ENDIAN
454 Defines the endianess of the CPU. Implementation of those
455 values is arch specific.
458 Freescale DDR driver in use. This type of DDR controller is
459 found in mpc83xx, mpc85xx, mpc86xx as well as some ARM core
462 CONFIG_SYS_FSL_DDR_ADDR
463 Freescale DDR memory-mapped register base.
465 CONFIG_SYS_FSL_DDR_EMU
466 Specify emulator support for DDR. Some DDR features such as
467 deskew training are not available.
469 CONFIG_SYS_FSL_DDRC_GEN1
470 Freescale DDR1 controller.
472 CONFIG_SYS_FSL_DDRC_GEN2
473 Freescale DDR2 controller.
475 CONFIG_SYS_FSL_DDRC_GEN3
476 Freescale DDR3 controller.
478 CONFIG_SYS_FSL_DDRC_GEN4
479 Freescale DDR4 controller.
481 CONFIG_SYS_FSL_DDRC_ARM_GEN3
482 Freescale DDR3 controller for ARM-based SoCs.
485 Board config to use DDR1. It can be enabled for SoCs with
486 Freescale DDR1 or DDR2 controllers, depending on the board
490 Board config to use DDR2. It can be eanbeld for SoCs with
491 Freescale DDR2 or DDR3 controllers, depending on the board
495 Board config to use DDR3. It can be enabled for SoCs with
496 Freescale DDR3 or DDR3L controllers.
499 Board config to use DDR3L. It can be enabled for SoCs with
503 Board config to use DDR4. It can be enabled for SoCs with
506 CONFIG_SYS_FSL_IFC_BE
507 Defines the IFC controller register space as Big Endian
509 CONFIG_SYS_FSL_IFC_LE
510 Defines the IFC controller register space as Little Endian
512 CONFIG_SYS_FSL_PBL_PBI
513 It enables addition of RCW (Power on reset configuration) in built image.
514 Please refer doc/README.pblimage for more details
516 CONFIG_SYS_FSL_PBL_RCW
517 It adds PBI(pre-boot instructions) commands in u-boot build image.
518 PBI commands can be used to configure SoC before it starts the execution.
519 Please refer doc/README.pblimage for more details
522 It adds a target to create boot binary having SPL binary in PBI format
523 concatenated with u-boot binary.
525 CONFIG_SYS_FSL_DDR_BE
526 Defines the DDR controller register space as Big Endian
528 CONFIG_SYS_FSL_DDR_LE
529 Defines the DDR controller register space as Little Endian
531 CONFIG_SYS_FSL_DDR_SDRAM_BASE_PHY
532 Physical address from the view of DDR controllers. It is the
533 same as CONFIG_SYS_DDR_SDRAM_BASE for all Power SoCs. But
534 it could be different for ARM SoCs.
536 CONFIG_SYS_FSL_DDR_INTLV_256B
537 DDR controller interleaving on 256-byte. This is a special
538 interleaving mode, handled by Dickens for Freescale layerscape
541 CONFIG_SYS_FSL_DDR_MAIN_NUM_CTRLS
542 Number of controllers used as main memory.
544 CONFIG_SYS_FSL_OTHER_DDR_NUM_CTRLS
545 Number of controllers used for other than main memory.
547 CONFIG_SYS_FSL_SEC_BE
548 Defines the SEC controller register space as Big Endian
550 CONFIG_SYS_FSL_SEC_LE
551 Defines the SEC controller register space as Little Endian
553 - Intel Monahans options:
554 CONFIG_SYS_MONAHANS_RUN_MODE_OSC_RATIO
556 Defines the Monahans run mode to oscillator
557 ratio. Valid values are 8, 16, 24, 31. The core
558 frequency is this value multiplied by 13 MHz.
560 CONFIG_SYS_MONAHANS_TURBO_RUN_MODE_RATIO
562 Defines the Monahans turbo mode to oscillator
563 ratio. Valid values are 1 (default if undefined) and
564 2. The core frequency as calculated above is multiplied
568 CONFIG_SYS_INIT_SP_OFFSET
570 Offset relative to CONFIG_SYS_SDRAM_BASE for initial stack
571 pointer. This is needed for the temporary stack before
574 CONFIG_SYS_MIPS_CACHE_MODE
576 Cache operation mode for the MIPS CPU.
577 See also arch/mips/include/asm/mipsregs.h.
579 CONF_CM_CACHABLE_NO_WA
582 CONF_CM_CACHABLE_NONCOHERENT
586 CONF_CM_CACHABLE_ACCELERATED
588 CONFIG_SYS_XWAY_EBU_BOOTCFG
590 Special option for Lantiq XWAY SoCs for booting from NOR flash.
591 See also arch/mips/cpu/mips32/start.S.
593 CONFIG_XWAY_SWAP_BYTES
595 Enable compilation of tools/xway-swap-bytes needed for Lantiq
596 XWAY SoCs for booting from NOR flash. The U-Boot image needs to
597 be swapped if a flash programmer is used.
600 CONFIG_SYS_EXCEPTION_VECTORS_HIGH
602 Select high exception vectors of the ARM core, e.g., do not
603 clear the V bit of the c1 register of CP15.
605 CONFIG_SYS_THUMB_BUILD
607 Use this flag to build U-Boot using the Thumb instruction
608 set for ARM architectures. Thumb instruction set provides
609 better code density. For ARM architectures that support
610 Thumb2 this flag will result in Thumb2 code generated by
613 CONFIG_ARM_ERRATA_716044
614 CONFIG_ARM_ERRATA_742230
615 CONFIG_ARM_ERRATA_743622
616 CONFIG_ARM_ERRATA_751472
617 CONFIG_ARM_ERRATA_794072
618 CONFIG_ARM_ERRATA_761320
620 If set, the workarounds for these ARM errata are applied early
621 during U-Boot startup. Note that these options force the
622 workarounds to be applied; no CPU-type/version detection
623 exists, unlike the similar options in the Linux kernel. Do not
624 set these options unless they apply!
626 - Linux Kernel Interface:
629 U-Boot stores all clock information in Hz
630 internally. For binary compatibility with older Linux
631 kernels (which expect the clocks passed in the
632 bd_info data to be in MHz) the environment variable
633 "clocks_in_mhz" can be defined so that U-Boot
634 converts clock data to MHZ before passing it to the
636 When CONFIG_CLOCKS_IN_MHZ is defined, a definition of
637 "clocks_in_mhz=1" is automatically included in the
640 CONFIG_MEMSIZE_IN_BYTES [relevant for MIPS only]
642 When transferring memsize parameter to linux, some versions
643 expect it to be in bytes, others in MB.
644 Define CONFIG_MEMSIZE_IN_BYTES to make it in bytes.
648 New kernel versions are expecting firmware settings to be
649 passed using flattened device trees (based on open firmware
653 * New libfdt-based support
654 * Adds the "fdt" command
655 * The bootm command automatically updates the fdt
657 OF_CPU - The proper name of the cpus node (only required for
658 MPC512X and MPC5xxx based boards).
659 OF_SOC - The proper name of the soc node (only required for
660 MPC512X and MPC5xxx based boards).
661 OF_TBCLK - The timebase frequency.
662 OF_STDOUT_PATH - The path to the console device
664 boards with QUICC Engines require OF_QE to set UCC MAC
667 CONFIG_OF_BOARD_SETUP
669 Board code has addition modification that it wants to make
670 to the flat device tree before handing it off to the kernel
674 This define fills in the correct boot CPU in the boot
675 param header, the default value is zero if undefined.
679 U-Boot can detect if an IDE device is present or not.
680 If not, and this new config option is activated, U-Boot
681 removes the ATA node from the DTS before booting Linux,
682 so the Linux IDE driver does not probe the device and
683 crash. This is needed for buggy hardware (uc101) where
684 no pull down resistor is connected to the signal IDE5V_DD7.
686 CONFIG_MACH_TYPE [relevant for ARM only][mandatory]
688 This setting is mandatory for all boards that have only one
689 machine type and must be used to specify the machine type
690 number as it appears in the ARM machine registry
691 (see http://www.arm.linux.org.uk/developer/machines/).
692 Only boards that have multiple machine types supported
693 in a single configuration file and the machine type is
694 runtime discoverable, do not have to use this setting.
696 - vxWorks boot parameters:
698 bootvx constructs a valid bootline using the following
699 environments variables: bootfile, ipaddr, serverip, hostname.
700 It loads the vxWorks image pointed bootfile.
702 CONFIG_SYS_VXWORKS_BOOT_DEVICE - The vxworks device name
703 CONFIG_SYS_VXWORKS_MAC_PTR - Ethernet 6 byte MA -address
704 CONFIG_SYS_VXWORKS_SERVERNAME - Name of the server
705 CONFIG_SYS_VXWORKS_BOOT_ADDR - Address of boot parameters
707 CONFIG_SYS_VXWORKS_ADD_PARAMS
709 Add it at the end of the bootline. E.g "u=username pw=secret"
711 Note: If a "bootargs" environment is defined, it will overwride
712 the defaults discussed just above.
714 - Cache Configuration:
715 CONFIG_SYS_ICACHE_OFF - Do not enable instruction cache in U-Boot
716 CONFIG_SYS_DCACHE_OFF - Do not enable data cache in U-Boot
717 CONFIG_SYS_L2CACHE_OFF- Do not enable L2 cache in U-Boot
719 - Cache Configuration for ARM:
720 CONFIG_SYS_L2_PL310 - Enable support for ARM PL310 L2 cache
722 CONFIG_SYS_PL310_BASE - Physical base address of PL310
723 controller register space
728 Define this if you want support for Amba PrimeCell PL010 UARTs.
732 Define this if you want support for Amba PrimeCell PL011 UARTs.
736 If you have Amba PrimeCell PL011 UARTs, set this variable to
737 the clock speed of the UARTs.
741 If you have Amba PrimeCell PL010 or PL011 UARTs on your board,
742 define this to a list of base addresses for each (supported)
743 port. See e.g. include/configs/versatile.h
745 CONFIG_PL011_SERIAL_RLCR
747 Some vendor versions of PL011 serial ports (e.g. ST-Ericsson U8500)
748 have separate receive and transmit line control registers. Set
749 this variable to initialize the extra register.
751 CONFIG_PL011_SERIAL_FLUSH_ON_INIT
753 On some platforms (e.g. U8500) U-Boot is loaded by a second stage
754 boot loader that has already initialized the UART. Define this
755 variable to flush the UART at init time.
757 CONFIG_SERIAL_HW_FLOW_CONTROL
759 Define this variable to enable hw flow control in serial driver.
760 Current user of this option is drivers/serial/nsl16550.c driver
763 Depending on board, define exactly one serial port
764 (like CONFIG_8xx_CONS_SMC1, CONFIG_8xx_CONS_SMC2,
765 CONFIG_8xx_CONS_SCC1, ...), or switch off the serial
766 console by defining CONFIG_8xx_CONS_NONE
768 Note: if CONFIG_8xx_CONS_NONE is defined, the serial
769 port routines must be defined elsewhere
770 (i.e. serial_init(), serial_getc(), ...)
773 Enables console device for a color framebuffer. Needs following
774 defines (cf. smiLynxEM, i8042)
775 VIDEO_FB_LITTLE_ENDIAN graphic memory organisation
777 VIDEO_HW_RECTFILL graphic chip supports
780 VIDEO_HW_BITBLT graphic chip supports
781 bit-blit (cf. smiLynxEM)
782 VIDEO_VISIBLE_COLS visible pixel columns
784 VIDEO_VISIBLE_ROWS visible pixel rows
785 VIDEO_PIXEL_SIZE bytes per pixel
786 VIDEO_DATA_FORMAT graphic data format
787 (0-5, cf. cfb_console.c)
788 VIDEO_FB_ADRS framebuffer address
789 VIDEO_KBD_INIT_FCT keyboard int fct
790 (i.e. i8042_kbd_init())
791 VIDEO_TSTC_FCT test char fct
793 VIDEO_GETC_FCT get char fct
795 CONFIG_CONSOLE_CURSOR cursor drawing on/off
796 (requires blink timer
798 CONFIG_SYS_CONSOLE_BLINK_COUNT blink interval (cf. i8042.c)
799 CONFIG_CONSOLE_TIME display time/date info in
801 (requires CONFIG_CMD_DATE)
802 CONFIG_VIDEO_LOGO display Linux logo in
804 CONFIG_VIDEO_BMP_LOGO use bmp_logo.h instead of
805 linux_logo.h for logo.
806 Requires CONFIG_VIDEO_LOGO
807 CONFIG_CONSOLE_EXTRA_INFO
808 additional board info beside
811 When CONFIG_CFB_CONSOLE_ANSI is defined, console will support
812 a limited number of ANSI escape sequences (cursor control,
813 erase functions and limited graphics rendition control).
815 When CONFIG_CFB_CONSOLE is defined, video console is
816 default i/o. Serial console can be forced with
817 environment 'console=serial'.
819 When CONFIG_SILENT_CONSOLE is defined, all console
820 messages (by U-Boot and Linux!) can be silenced with
821 the "silent" environment variable. See
822 doc/README.silent for more information.
824 CONFIG_SYS_CONSOLE_BG_COL: define the backgroundcolor, default
826 CONFIG_SYS_CONSOLE_FG_COL: define the foregroundcolor, default
830 CONFIG_BAUDRATE - in bps
831 Select one of the baudrates listed in
832 CONFIG_SYS_BAUDRATE_TABLE, see below.
833 CONFIG_SYS_BRGCLK_PRESCALE, baudrate prescale
835 - Console Rx buffer length
836 With CONFIG_SYS_SMC_RXBUFLEN it is possible to define
837 the maximum receive buffer length for the SMC.
838 This option is actual only for 82xx and 8xx possible.
839 If using CONFIG_SYS_SMC_RXBUFLEN also CONFIG_SYS_MAXIDLE
840 must be defined, to setup the maximum idle timeout for
843 - Pre-Console Buffer:
844 Prior to the console being initialised (i.e. serial UART
845 initialised etc) all console output is silently discarded.
846 Defining CONFIG_PRE_CONSOLE_BUFFER will cause U-Boot to
847 buffer any console messages prior to the console being
848 initialised to a buffer of size CONFIG_PRE_CON_BUF_SZ
849 bytes located at CONFIG_PRE_CON_BUF_ADDR. The buffer is
850 a circular buffer, so if more than CONFIG_PRE_CON_BUF_SZ
851 bytes are output before the console is initialised, the
852 earlier bytes are discarded.
854 'Sane' compilers will generate smaller code if
855 CONFIG_PRE_CON_BUF_SZ is a power of 2
857 - Safe printf() functions
858 Define CONFIG_SYS_VSNPRINTF to compile in safe versions of
859 the printf() functions. These are defined in
860 include/vsprintf.h and include snprintf(), vsnprintf() and
861 so on. Code size increase is approximately 300-500 bytes.
862 If this option is not given then these functions will
863 silently discard their buffer size argument - this means
864 you are not getting any overflow checking in this case.
866 - Boot Delay: CONFIG_BOOTDELAY - in seconds
867 Delay before automatically booting the default image;
868 set to -1 to disable autoboot.
869 set to -2 to autoboot with no delay and not check for abort
870 (even when CONFIG_ZERO_BOOTDELAY_CHECK is defined).
872 See doc/README.autoboot for these options that
873 work with CONFIG_BOOTDELAY. None are required.
874 CONFIG_BOOT_RETRY_TIME
875 CONFIG_BOOT_RETRY_MIN
876 CONFIG_AUTOBOOT_KEYED
877 CONFIG_AUTOBOOT_PROMPT
878 CONFIG_AUTOBOOT_DELAY_STR
879 CONFIG_AUTOBOOT_STOP_STR
880 CONFIG_AUTOBOOT_DELAY_STR2
881 CONFIG_AUTOBOOT_STOP_STR2
882 CONFIG_ZERO_BOOTDELAY_CHECK
883 CONFIG_RESET_TO_RETRY
887 Only needed when CONFIG_BOOTDELAY is enabled;
888 define a command string that is automatically executed
889 when no character is read on the console interface
890 within "Boot Delay" after reset.
893 This can be used to pass arguments to the bootm
894 command. The value of CONFIG_BOOTARGS goes into the
895 environment value "bootargs".
897 CONFIG_RAMBOOT and CONFIG_NFSBOOT
898 The value of these goes into the environment as
899 "ramboot" and "nfsboot" respectively, and can be used
900 as a convenience, when switching between booting from
904 CONFIG_BOOTCOUNT_LIMIT
905 Implements a mechanism for detecting a repeating reboot
907 http://www.denx.de/wiki/view/DULG/UBootBootCountLimit
910 If no softreset save registers are found on the hardware
911 "bootcount" is stored in the environment. To prevent a
912 saveenv on all reboots, the environment variable
913 "upgrade_available" is used. If "upgrade_available" is
914 0, "bootcount" is always 0, if "upgrade_available" is
915 1 "bootcount" is incremented in the environment.
916 So the Userspace Applikation must set the "upgrade_available"
917 and "bootcount" variable to 0, if a boot was successfully.
922 When this option is #defined, the existence of the
923 environment variable "preboot" will be checked
924 immediately before starting the CONFIG_BOOTDELAY
925 countdown and/or running the auto-boot command resp.
926 entering interactive mode.
928 This feature is especially useful when "preboot" is
929 automatically generated or modified. For an example
930 see the LWMON board specific code: here "preboot" is
931 modified when the user holds down a certain
932 combination of keys on the (special) keyboard when
935 - Serial Download Echo Mode:
937 If defined to 1, all characters received during a
938 serial download (using the "loads" command) are
939 echoed back. This might be needed by some terminal
940 emulations (like "cu"), but may as well just take
941 time on others. This setting #define's the initial
942 value of the "loads_echo" environment variable.
944 - Kgdb Serial Baudrate: (if CONFIG_CMD_KGDB is defined)
946 Select one of the baudrates listed in
947 CONFIG_SYS_BAUDRATE_TABLE, see below.
950 Monitor commands can be included or excluded
951 from the build by using the #include files
952 <config_cmd_all.h> and #undef'ing unwanted
953 commands, or using <config_cmd_default.h>
954 and augmenting with additional #define's
957 The default command configuration includes all commands
958 except those marked below with a "*".
960 CONFIG_CMD_AES AES 128 CBC encrypt/decrypt
961 CONFIG_CMD_ASKENV * ask for env variable
962 CONFIG_CMD_BDI bdinfo
963 CONFIG_CMD_BEDBUG * Include BedBug Debugger
964 CONFIG_CMD_BMP * BMP support
965 CONFIG_CMD_BSP * Board specific commands
966 CONFIG_CMD_BOOTD bootd
967 CONFIG_CMD_BOOTI * ARM64 Linux kernel Image support
968 CONFIG_CMD_CACHE * icache, dcache
969 CONFIG_CMD_CLK * clock command support
970 CONFIG_CMD_CONSOLE coninfo
971 CONFIG_CMD_CRC32 * crc32
972 CONFIG_CMD_DATE * support for RTC, date/time...
973 CONFIG_CMD_DHCP * DHCP support
974 CONFIG_CMD_DIAG * Diagnostics
975 CONFIG_CMD_DS4510 * ds4510 I2C gpio commands
976 CONFIG_CMD_DS4510_INFO * ds4510 I2C info command
977 CONFIG_CMD_DS4510_MEM * ds4510 I2C eeprom/sram commansd
978 CONFIG_CMD_DS4510_RST * ds4510 I2C rst command
979 CONFIG_CMD_DTT * Digital Therm and Thermostat
980 CONFIG_CMD_ECHO echo arguments
981 CONFIG_CMD_EDITENV edit env variable
982 CONFIG_CMD_EEPROM * EEPROM read/write support
983 CONFIG_CMD_ELF * bootelf, bootvx
984 CONFIG_CMD_ENV_CALLBACK * display details about env callbacks
985 CONFIG_CMD_ENV_FLAGS * display details about env flags
986 CONFIG_CMD_ENV_EXISTS * check existence of env variable
987 CONFIG_CMD_EXPORTENV * export the environment
988 CONFIG_CMD_EXT2 * ext2 command support
989 CONFIG_CMD_EXT4 * ext4 command support
990 CONFIG_CMD_FS_GENERIC * filesystem commands (e.g. load, ls)
991 that work for multiple fs types
992 CONFIG_CMD_SAVEENV saveenv
993 CONFIG_CMD_FDC * Floppy Disk Support
994 CONFIG_CMD_FAT * FAT command support
995 CONFIG_CMD_FLASH flinfo, erase, protect
996 CONFIG_CMD_FPGA FPGA device initialization support
997 CONFIG_CMD_FUSE * Device fuse support
998 CONFIG_CMD_GETTIME * Get time since boot
999 CONFIG_CMD_GO * the 'go' command (exec code)
1000 CONFIG_CMD_GREPENV * search environment
1001 CONFIG_CMD_HASH * calculate hash / digest
1002 CONFIG_CMD_HWFLOW * RTS/CTS hw flow control
1003 CONFIG_CMD_I2C * I2C serial bus support
1004 CONFIG_CMD_IDE * IDE harddisk support
1005 CONFIG_CMD_IMI iminfo
1006 CONFIG_CMD_IMLS List all images found in NOR flash
1007 CONFIG_CMD_IMLS_NAND * List all images found in NAND flash
1008 CONFIG_CMD_IMMAP * IMMR dump support
1009 CONFIG_CMD_IOTRACE * I/O tracing for debugging
1010 CONFIG_CMD_IMPORTENV * import an environment
1011 CONFIG_CMD_INI * import data from an ini file into the env
1012 CONFIG_CMD_IRQ * irqinfo
1013 CONFIG_CMD_ITEST Integer/string test of 2 values
1014 CONFIG_CMD_JFFS2 * JFFS2 Support
1015 CONFIG_CMD_KGDB * kgdb
1016 CONFIG_CMD_LDRINFO * ldrinfo (display Blackfin loader)
1017 CONFIG_CMD_LINK_LOCAL * link-local IP address auto-configuration
1019 CONFIG_CMD_LOADB loadb
1020 CONFIG_CMD_LOADS loads
1021 CONFIG_CMD_MD5SUM * print md5 message digest
1022 (requires CONFIG_CMD_MEMORY and CONFIG_MD5)
1023 CONFIG_CMD_MEMINFO * Display detailed memory information
1024 CONFIG_CMD_MEMORY md, mm, nm, mw, cp, cmp, crc, base,
1026 CONFIG_CMD_MEMTEST * mtest
1027 CONFIG_CMD_MISC Misc functions like sleep etc
1028 CONFIG_CMD_MMC * MMC memory mapped support
1029 CONFIG_CMD_MII * MII utility commands
1030 CONFIG_CMD_MTDPARTS * MTD partition support
1031 CONFIG_CMD_NAND * NAND support
1032 CONFIG_CMD_NET bootp, tftpboot, rarpboot
1033 CONFIG_CMD_NFS NFS support
1034 CONFIG_CMD_PCA953X * PCA953x I2C gpio commands
1035 CONFIG_CMD_PCA953X_INFO * PCA953x I2C gpio info command
1036 CONFIG_CMD_PCI * pciinfo
1037 CONFIG_CMD_PCMCIA * PCMCIA support
1038 CONFIG_CMD_PING * send ICMP ECHO_REQUEST to network
1040 CONFIG_CMD_PORTIO * Port I/O
1041 CONFIG_CMD_READ * Read raw data from partition
1042 CONFIG_CMD_REGINFO * Register dump
1043 CONFIG_CMD_RUN run command in env variable
1044 CONFIG_CMD_SANDBOX * sb command to access sandbox features
1045 CONFIG_CMD_SAVES * save S record dump
1046 CONFIG_CMD_SCSI * SCSI Support
1047 CONFIG_CMD_SDRAM * print SDRAM configuration information
1048 (requires CONFIG_CMD_I2C)
1049 CONFIG_CMD_SETGETDCR Support for DCR Register access
1051 CONFIG_CMD_SF * Read/write/erase SPI NOR flash
1052 CONFIG_CMD_SHA1SUM * print sha1 memory digest
1053 (requires CONFIG_CMD_MEMORY)
1054 CONFIG_CMD_SOFTSWITCH * Soft switch setting command for BF60x
1055 CONFIG_CMD_SOURCE "source" command Support
1056 CONFIG_CMD_SPI * SPI serial bus support
1057 CONFIG_CMD_TFTPSRV * TFTP transfer in server mode
1058 CONFIG_CMD_TFTPPUT * TFTP put command (upload)
1059 CONFIG_CMD_TIME * run command and report execution time (ARM specific)
1060 CONFIG_CMD_TIMER * access to the system tick timer
1061 CONFIG_CMD_USB * USB support
1062 CONFIG_CMD_CDP * Cisco Discover Protocol support
1063 CONFIG_CMD_MFSL * Microblaze FSL support
1064 CONFIG_CMD_XIMG Load part of Multi Image
1065 CONFIG_CMD_UUID * Generate random UUID or GUID string
1067 EXAMPLE: If you want all functions except of network
1068 support you can write:
1070 #include "config_cmd_all.h"
1071 #undef CONFIG_CMD_NET
1074 fdt (flattened device tree) command: CONFIG_OF_LIBFDT
1076 Note: Don't enable the "icache" and "dcache" commands
1077 (configuration option CONFIG_CMD_CACHE) unless you know
1078 what you (and your U-Boot users) are doing. Data
1079 cache cannot be enabled on systems like the 8xx or
1080 8260 (where accesses to the IMMR region must be
1081 uncached), and it cannot be disabled on all other
1082 systems where we (mis-) use the data cache to hold an
1083 initial stack and some data.
1086 XXX - this list needs to get updated!
1088 - Regular expression support:
1090 If this variable is defined, U-Boot is linked against
1091 the SLRE (Super Light Regular Expression) library,
1092 which adds regex support to some commands, as for
1093 example "env grep" and "setexpr".
1097 If this variable is defined, U-Boot will use a device tree
1098 to configure its devices, instead of relying on statically
1099 compiled #defines in the board file. This option is
1100 experimental and only available on a few boards. The device
1101 tree is available in the global data as gd->fdt_blob.
1103 U-Boot needs to get its device tree from somewhere. This can
1104 be done using one of the two options below:
1107 If this variable is defined, U-Boot will embed a device tree
1108 binary in its image. This device tree file should be in the
1109 board directory and called <soc>-<board>.dts. The binary file
1110 is then picked up in board_init_f() and made available through
1111 the global data structure as gd->blob.
1114 If this variable is defined, U-Boot will build a device tree
1115 binary. It will be called u-boot.dtb. Architecture-specific
1116 code will locate it at run-time. Generally this works by:
1118 cat u-boot.bin u-boot.dtb >image.bin
1120 and in fact, U-Boot does this for you, creating a file called
1121 u-boot-dtb.bin which is useful in the common case. You can
1122 still use the individual files if you need something more
1127 If this variable is defined, it enables watchdog
1128 support for the SoC. There must be support in the SoC
1129 specific code for a watchdog. For the 8xx and 8260
1130 CPUs, the SIU Watchdog feature is enabled in the SYPCR
1131 register. When supported for a specific SoC is
1132 available, then no further board specific code should
1133 be needed to use it.
1136 When using a watchdog circuitry external to the used
1137 SoC, then define this variable and provide board
1138 specific code for the "hw_watchdog_reset" function.
1141 CONFIG_VERSION_VARIABLE
1142 If this variable is defined, an environment variable
1143 named "ver" is created by U-Boot showing the U-Boot
1144 version as printed by the "version" command.
1145 Any change to this variable will be reverted at the
1150 When CONFIG_CMD_DATE is selected, the type of the RTC
1151 has to be selected, too. Define exactly one of the
1154 CONFIG_RTC_MPC8xx - use internal RTC of MPC8xx
1155 CONFIG_RTC_PCF8563 - use Philips PCF8563 RTC
1156 CONFIG_RTC_MC13XXX - use MC13783 or MC13892 RTC
1157 CONFIG_RTC_MC146818 - use MC146818 RTC
1158 CONFIG_RTC_DS1307 - use Maxim, Inc. DS1307 RTC
1159 CONFIG_RTC_DS1337 - use Maxim, Inc. DS1337 RTC
1160 CONFIG_RTC_DS1338 - use Maxim, Inc. DS1338 RTC
1161 CONFIG_RTC_DS1339 - use Maxim, Inc. DS1339 RTC
1162 CONFIG_RTC_DS164x - use Dallas DS164x RTC
1163 CONFIG_RTC_ISL1208 - use Intersil ISL1208 RTC
1164 CONFIG_RTC_MAX6900 - use Maxim, Inc. MAX6900 RTC
1165 CONFIG_SYS_RTC_DS1337_NOOSC - Turn off the OSC output for DS1337
1166 CONFIG_SYS_RV3029_TCR - enable trickle charger on
1169 Note that if the RTC uses I2C, then the I2C interface
1170 must also be configured. See I2C Support, below.
1173 CONFIG_PCA953X - use NXP's PCA953X series I2C GPIO
1175 The CONFIG_SYS_I2C_PCA953X_WIDTH option specifies a list of
1176 chip-ngpio pairs that tell the PCA953X driver the number of
1177 pins supported by a particular chip.
1179 Note that if the GPIO device uses I2C, then the I2C interface
1180 must also be configured. See I2C Support, below.
1183 When CONFIG_IO_TRACE is selected, U-Boot intercepts all I/O
1184 accesses and can checksum them or write a list of them out
1185 to memory. See the 'iotrace' command for details. This is
1186 useful for testing device drivers since it can confirm that
1187 the driver behaves the same way before and after a code
1188 change. Currently this is supported on sandbox and arm. To
1189 add support for your architecture, add '#include <iotrace.h>'
1190 to the bottom of arch/<arch>/include/asm/io.h and test.
1192 Example output from the 'iotrace stats' command is below.
1193 Note that if the trace buffer is exhausted, the checksum will
1194 still continue to operate.
1197 Start: 10000000 (buffer start address)
1198 Size: 00010000 (buffer size)
1199 Offset: 00000120 (current buffer offset)
1200 Output: 10000120 (start + offset)
1201 Count: 00000018 (number of trace records)
1202 CRC32: 9526fb66 (CRC32 of all trace records)
1204 - Timestamp Support:
1206 When CONFIG_TIMESTAMP is selected, the timestamp
1207 (date and time) of an image is printed by image
1208 commands like bootm or iminfo. This option is
1209 automatically enabled when you select CONFIG_CMD_DATE .
1211 - Partition Labels (disklabels) Supported:
1212 Zero or more of the following:
1213 CONFIG_MAC_PARTITION Apple's MacOS partition table.
1214 CONFIG_DOS_PARTITION MS Dos partition table, traditional on the
1215 Intel architecture, USB sticks, etc.
1216 CONFIG_ISO_PARTITION ISO partition table, used on CDROM etc.
1217 CONFIG_EFI_PARTITION GPT partition table, common when EFI is the
1218 bootloader. Note 2TB partition limit; see
1220 CONFIG_MTD_PARTITIONS Memory Technology Device partition table.
1222 If IDE or SCSI support is enabled (CONFIG_CMD_IDE or
1223 CONFIG_CMD_SCSI) you must configure support for at
1224 least one non-MTD partition type as well.
1227 CONFIG_IDE_RESET_ROUTINE - this is defined in several
1228 board configurations files but used nowhere!
1230 CONFIG_IDE_RESET - is this is defined, IDE Reset will
1231 be performed by calling the function
1232 ide_set_reset(int reset)
1233 which has to be defined in a board specific file
1238 Set this to enable ATAPI support.
1243 Set this to enable support for disks larger than 137GB
1244 Also look at CONFIG_SYS_64BIT_LBA.
1245 Whithout these , LBA48 support uses 32bit variables and will 'only'
1246 support disks up to 2.1TB.
1248 CONFIG_SYS_64BIT_LBA:
1249 When enabled, makes the IDE subsystem use 64bit sector addresses.
1253 At the moment only there is only support for the
1254 SYM53C8XX SCSI controller; define
1255 CONFIG_SCSI_SYM53C8XX to enable it.
1257 CONFIG_SYS_SCSI_MAX_LUN [8], CONFIG_SYS_SCSI_MAX_SCSI_ID [7] and
1258 CONFIG_SYS_SCSI_MAX_DEVICE [CONFIG_SYS_SCSI_MAX_SCSI_ID *
1259 CONFIG_SYS_SCSI_MAX_LUN] can be adjusted to define the
1260 maximum numbers of LUNs, SCSI ID's and target
1262 CONFIG_SYS_SCSI_SYM53C8XX_CCF to fix clock timing (80Mhz)
1264 The environment variable 'scsidevs' is set to the number of
1265 SCSI devices found during the last scan.
1267 - NETWORK Support (PCI):
1269 Support for Intel 8254x/8257x gigabit chips.
1272 Utility code for direct access to the SPI bus on Intel 8257x.
1273 This does not do anything useful unless you set at least one
1274 of CONFIG_CMD_E1000 or CONFIG_E1000_SPI_GENERIC.
1276 CONFIG_E1000_SPI_GENERIC
1277 Allow generic access to the SPI bus on the Intel 8257x, for
1278 example with the "sspi" command.
1281 Management command for E1000 devices. When used on devices
1282 with SPI support you can reprogram the EEPROM from U-Boot.
1284 CONFIG_E1000_FALLBACK_MAC
1285 default MAC for empty EEPROM after production.
1288 Support for Intel 82557/82559/82559ER chips.
1289 Optional CONFIG_EEPRO100_SROM_WRITE enables EEPROM
1290 write routine for first time initialisation.
1293 Support for Digital 2114x chips.
1294 Optional CONFIG_TULIP_SELECT_MEDIA for board specific
1295 modem chip initialisation (KS8761/QS6611).
1298 Support for National dp83815 chips.
1301 Support for National dp8382[01] gigabit chips.
1303 - NETWORK Support (other):
1305 CONFIG_DRIVER_AT91EMAC
1306 Support for AT91RM9200 EMAC.
1309 Define this to use reduced MII inteface
1311 CONFIG_DRIVER_AT91EMAC_QUIET
1312 If this defined, the driver is quiet.
1313 The driver doen't show link status messages.
1315 CONFIG_CALXEDA_XGMAC
1316 Support for the Calxeda XGMAC device
1319 Support for SMSC's LAN91C96 chips.
1321 CONFIG_LAN91C96_BASE
1322 Define this to hold the physical address
1323 of the LAN91C96's I/O space
1325 CONFIG_LAN91C96_USE_32_BIT
1326 Define this to enable 32 bit addressing
1329 Support for SMSC's LAN91C111 chip
1331 CONFIG_SMC91111_BASE
1332 Define this to hold the physical address
1333 of the device (I/O space)
1335 CONFIG_SMC_USE_32_BIT
1336 Define this if data bus is 32 bits
1338 CONFIG_SMC_USE_IOFUNCS
1339 Define this to use i/o functions instead of macros
1340 (some hardware wont work with macros)
1342 CONFIG_DRIVER_TI_EMAC
1343 Support for davinci emac
1345 CONFIG_SYS_DAVINCI_EMAC_PHY_COUNT
1346 Define this if you have more then 3 PHYs.
1349 Support for Faraday's FTGMAC100 Gigabit SoC Ethernet
1351 CONFIG_FTGMAC100_EGIGA
1352 Define this to use GE link update with gigabit PHY.
1353 Define this if FTGMAC100 is connected to gigabit PHY.
1354 If your system has 10/100 PHY only, it might not occur
1355 wrong behavior. Because PHY usually return timeout or
1356 useless data when polling gigabit status and gigabit
1357 control registers. This behavior won't affect the
1358 correctnessof 10/100 link speed update.
1361 Support for SMSC's LAN911x and LAN921x chips
1364 Define this to hold the physical address
1365 of the device (I/O space)
1367 CONFIG_SMC911X_32_BIT
1368 Define this if data bus is 32 bits
1370 CONFIG_SMC911X_16_BIT
1371 Define this if data bus is 16 bits. If your processor
1372 automatically converts one 32 bit word to two 16 bit
1373 words you may also try CONFIG_SMC911X_32_BIT.
1376 Support for Renesas on-chip Ethernet controller
1378 CONFIG_SH_ETHER_USE_PORT
1379 Define the number of ports to be used
1381 CONFIG_SH_ETHER_PHY_ADDR
1382 Define the ETH PHY's address
1384 CONFIG_SH_ETHER_CACHE_WRITEBACK
1385 If this option is set, the driver enables cache flush.
1389 Support for PWM modul on the imx6.
1393 Support TPM devices.
1396 Support for i2c bus TPM devices. Only one device
1397 per system is supported at this time.
1399 CONFIG_TPM_TIS_I2C_BUS_NUMBER
1400 Define the the i2c bus number for the TPM device
1402 CONFIG_TPM_TIS_I2C_SLAVE_ADDRESS
1403 Define the TPM's address on the i2c bus
1405 CONFIG_TPM_TIS_I2C_BURST_LIMITATION
1406 Define the burst count bytes upper limit
1408 CONFIG_TPM_ATMEL_TWI
1409 Support for Atmel TWI TPM device. Requires I2C support.
1412 Support for generic parallel port TPM devices. Only one device
1413 per system is supported at this time.
1415 CONFIG_TPM_TIS_BASE_ADDRESS
1416 Base address where the generic TPM device is mapped
1417 to. Contemporary x86 systems usually map it at
1421 Add tpm monitor functions.
1422 Requires CONFIG_TPM. If CONFIG_TPM_AUTH_SESSIONS is set, also
1423 provides monitor access to authorized functions.
1426 Define this to enable the TPM support library which provides
1427 functional interfaces to some TPM commands.
1428 Requires support for a TPM device.
1430 CONFIG_TPM_AUTH_SESSIONS
1431 Define this to enable authorized functions in the TPM library.
1432 Requires CONFIG_TPM and CONFIG_SHA1.
1435 At the moment only the UHCI host controller is
1436 supported (PIP405, MIP405, MPC5200); define
1437 CONFIG_USB_UHCI to enable it.
1438 define CONFIG_USB_KEYBOARD to enable the USB Keyboard
1439 and define CONFIG_USB_STORAGE to enable the USB
1442 Supported are USB Keyboards and USB Floppy drives
1444 MPC5200 USB requires additional defines:
1446 for 528 MHz Clock: 0x0001bbbb
1450 for differential drivers: 0x00001000
1451 for single ended drivers: 0x00005000
1452 for differential drivers on PSC3: 0x00000100
1453 for single ended drivers on PSC3: 0x00004100
1454 CONFIG_SYS_USB_EVENT_POLL
1455 May be defined to allow interrupt polling
1456 instead of using asynchronous interrupts
1458 CONFIG_USB_EHCI_TXFIFO_THRESH enables setting of the
1459 txfilltuning field in the EHCI controller on reset.
1461 CONFIG_USB_DWC2_REG_ADDR the physical CPU address of the DWC2
1462 HW module registers.
1465 Define the below if you wish to use the USB console.
1466 Once firmware is rebuilt from a serial console issue the
1467 command "setenv stdin usbtty; setenv stdout usbtty" and
1468 attach your USB cable. The Unix command "dmesg" should print
1469 it has found a new device. The environment variable usbtty
1470 can be set to gserial or cdc_acm to enable your device to
1471 appear to a USB host as a Linux gserial device or a
1472 Common Device Class Abstract Control Model serial device.
1473 If you select usbtty = gserial you should be able to enumerate
1475 # modprobe usbserial vendor=0xVendorID product=0xProductID
1476 else if using cdc_acm, simply setting the environment
1477 variable usbtty to be cdc_acm should suffice. The following
1478 might be defined in YourBoardName.h
1481 Define this to build a UDC device
1484 Define this to have a tty type of device available to
1485 talk to the UDC device
1488 Define this to enable the high speed support for usb
1489 device and usbtty. If this feature is enabled, a routine
1490 int is_usbd_high_speed(void)
1491 also needs to be defined by the driver to dynamically poll
1492 whether the enumeration has succeded at high speed or full
1495 CONFIG_SYS_CONSOLE_IS_IN_ENV
1496 Define this if you want stdin, stdout &/or stderr to
1500 CONFIG_SYS_USB_EXTC_CLK 0xBLAH
1501 Derive USB clock from external clock "blah"
1502 - CONFIG_SYS_USB_EXTC_CLK 0x02
1504 CONFIG_SYS_USB_BRG_CLK 0xBLAH
1505 Derive USB clock from brgclk
1506 - CONFIG_SYS_USB_BRG_CLK 0x04
1508 If you have a USB-IF assigned VendorID then you may wish to
1509 define your own vendor specific values either in BoardName.h
1510 or directly in usbd_vendor_info.h. If you don't define
1511 CONFIG_USBD_MANUFACTURER, CONFIG_USBD_PRODUCT_NAME,
1512 CONFIG_USBD_VENDORID and CONFIG_USBD_PRODUCTID, then U-Boot
1513 should pretend to be a Linux device to it's target host.
1515 CONFIG_USBD_MANUFACTURER
1516 Define this string as the name of your company for
1517 - CONFIG_USBD_MANUFACTURER "my company"
1519 CONFIG_USBD_PRODUCT_NAME
1520 Define this string as the name of your product
1521 - CONFIG_USBD_PRODUCT_NAME "acme usb device"
1523 CONFIG_USBD_VENDORID
1524 Define this as your assigned Vendor ID from the USB
1525 Implementors Forum. This *must* be a genuine Vendor ID
1526 to avoid polluting the USB namespace.
1527 - CONFIG_USBD_VENDORID 0xFFFF
1529 CONFIG_USBD_PRODUCTID
1530 Define this as the unique Product ID
1532 - CONFIG_USBD_PRODUCTID 0xFFFF
1534 - ULPI Layer Support:
1535 The ULPI (UTMI Low Pin (count) Interface) PHYs are supported via
1536 the generic ULPI layer. The generic layer accesses the ULPI PHY
1537 via the platform viewport, so you need both the genric layer and
1538 the viewport enabled. Currently only Chipidea/ARC based
1539 viewport is supported.
1540 To enable the ULPI layer support, define CONFIG_USB_ULPI and
1541 CONFIG_USB_ULPI_VIEWPORT in your board configuration file.
1542 If your ULPI phy needs a different reference clock than the
1543 standard 24 MHz then you have to define CONFIG_ULPI_REF_CLK to
1544 the appropriate value in Hz.
1547 The MMC controller on the Intel PXA is supported. To
1548 enable this define CONFIG_MMC. The MMC can be
1549 accessed from the boot prompt by mapping the device
1550 to physical memory similar to flash. Command line is
1551 enabled with CONFIG_CMD_MMC. The MMC driver also works with
1552 the FAT fs. This is enabled with CONFIG_CMD_FAT.
1555 Support for Renesas on-chip MMCIF controller
1557 CONFIG_SH_MMCIF_ADDR
1558 Define the base address of MMCIF registers
1561 Define the clock frequency for MMCIF
1564 Enable the generic MMC driver
1566 CONFIG_SUPPORT_EMMC_BOOT
1567 Enable some additional features of the eMMC boot partitions.
1569 CONFIG_SUPPORT_EMMC_RPMB
1570 Enable the commands for reading, writing and programming the
1571 key for the Replay Protection Memory Block partition in eMMC.
1573 - USB Device Firmware Update (DFU) class support:
1575 This enables the USB portion of the DFU USB class
1578 This enables the command "dfu" which is used to have
1579 U-Boot create a DFU class device via USB. This command
1580 requires that the "dfu_alt_info" environment variable be
1581 set and define the alt settings to expose to the host.
1584 This enables support for exposing (e)MMC devices via DFU.
1587 This enables support for exposing NAND devices via DFU.
1590 This enables support for exposing RAM via DFU.
1591 Note: DFU spec refer to non-volatile memory usage, but
1592 allow usages beyond the scope of spec - here RAM usage,
1593 one that would help mostly the developer.
1595 CONFIG_SYS_DFU_DATA_BUF_SIZE
1596 Dfu transfer uses a buffer before writing data to the
1597 raw storage device. Make the size (in bytes) of this buffer
1598 configurable. The size of this buffer is also configurable
1599 through the "dfu_bufsiz" environment variable.
1601 CONFIG_SYS_DFU_MAX_FILE_SIZE
1602 When updating files rather than the raw storage device,
1603 we use a static buffer to copy the file into and then write
1604 the buffer once we've been given the whole file. Define
1605 this to the maximum filesize (in bytes) for the buffer.
1606 Default is 4 MiB if undefined.
1608 DFU_DEFAULT_POLL_TIMEOUT
1609 Poll timeout [ms], is the timeout a device can send to the
1610 host. The host must wait for this timeout before sending
1611 a subsequent DFU_GET_STATUS request to the device.
1613 DFU_MANIFEST_POLL_TIMEOUT
1614 Poll timeout [ms], which the device sends to the host when
1615 entering dfuMANIFEST state. Host waits this timeout, before
1616 sending again an USB request to the device.
1618 - USB Device Android Fastboot support:
1620 This enables the command "fastboot" which enables the Android
1621 fastboot mode for the platform's USB device. Fastboot is a USB
1622 protocol for downloading images, flashing and device control
1623 used on Android devices.
1624 See doc/README.android-fastboot for more information.
1626 CONFIG_ANDROID_BOOT_IMAGE
1627 This enables support for booting images which use the Android
1628 image format header.
1630 CONFIG_USB_FASTBOOT_BUF_ADDR
1631 The fastboot protocol requires a large memory buffer for
1632 downloads. Define this to the starting RAM address to use for
1635 CONFIG_USB_FASTBOOT_BUF_SIZE
1636 The fastboot protocol requires a large memory buffer for
1637 downloads. This buffer should be as large as possible for a
1638 platform. Define this to the size available RAM for fastboot.
1640 CONFIG_FASTBOOT_FLASH
1641 The fastboot protocol includes a "flash" command for writing
1642 the downloaded image to a non-volatile storage device. Define
1643 this to enable the "fastboot flash" command.
1645 CONFIG_FASTBOOT_FLASH_MMC_DEV
1646 The fastboot "flash" command requires additional information
1647 regarding the non-volatile storage device. Define this to
1648 the eMMC device that fastboot should use to store the image.
1650 - Journaling Flash filesystem support:
1651 CONFIG_JFFS2_NAND, CONFIG_JFFS2_NAND_OFF, CONFIG_JFFS2_NAND_SIZE,
1652 CONFIG_JFFS2_NAND_DEV
1653 Define these for a default partition on a NAND device
1655 CONFIG_SYS_JFFS2_FIRST_SECTOR,
1656 CONFIG_SYS_JFFS2_FIRST_BANK, CONFIG_SYS_JFFS2_NUM_BANKS
1657 Define these for a default partition on a NOR device
1659 CONFIG_SYS_JFFS_CUSTOM_PART
1660 Define this to create an own partition. You have to provide a
1661 function struct part_info* jffs2_part_info(int part_num)
1663 If you define only one JFFS2 partition you may also want to
1664 #define CONFIG_SYS_JFFS_SINGLE_PART 1
1665 to disable the command chpart. This is the default when you
1666 have not defined a custom partition
1668 - FAT(File Allocation Table) filesystem write function support:
1671 Define this to enable support for saving memory data as a
1672 file in FAT formatted partition.
1674 This will also enable the command "fatwrite" enabling the
1675 user to write files to FAT.
1677 CBFS (Coreboot Filesystem) support
1680 Define this to enable support for reading from a Coreboot
1681 filesystem. Available commands are cbfsinit, cbfsinfo, cbfsls
1684 - FAT(File Allocation Table) filesystem cluster size:
1685 CONFIG_FS_FAT_MAX_CLUSTSIZE
1687 Define the max cluster size for fat operations else
1688 a default value of 65536 will be defined.
1693 Define this to enable standard (PC-Style) keyboard
1697 Standard PC keyboard driver with US (is default) and
1698 GERMAN key layout (switch via environment 'keymap=de') support.
1699 Export function i8042_kbd_init, i8042_tstc and i8042_getc
1700 for cfb_console. Supports cursor blinking.
1703 Enables a Chrome OS keyboard using the CROS_EC interface.
1704 This uses CROS_EC to communicate with a second microcontroller
1705 which provides key scans on request.
1710 Define this to enable video support (for output to
1713 CONFIG_VIDEO_CT69000
1715 Enable Chips & Technologies 69000 Video chip
1717 CONFIG_VIDEO_SMI_LYNXEM
1718 Enable Silicon Motion SMI 712/710/810 Video chip. The
1719 video output is selected via environment 'videoout'
1720 (1 = LCD and 2 = CRT). If videoout is undefined, CRT is
1723 For the CT69000 and SMI_LYNXEM drivers, videomode is
1724 selected via environment 'videomode'. Two different ways
1726 - "videomode=num" 'num' is a standard LiLo mode numbers.
1727 Following standard modes are supported (* is default):
1729 Colors 640x480 800x600 1024x768 1152x864 1280x1024
1730 -------------+---------------------------------------------
1731 8 bits | 0x301* 0x303 0x305 0x161 0x307
1732 15 bits | 0x310 0x313 0x316 0x162 0x319
1733 16 bits | 0x311 0x314 0x317 0x163 0x31A
1734 24 bits | 0x312 0x315 0x318 ? 0x31B
1735 -------------+---------------------------------------------
1736 (i.e. setenv videomode 317; saveenv; reset;)
1738 - "videomode=bootargs" all the video parameters are parsed
1739 from the bootargs. (See drivers/video/videomodes.c)
1742 CONFIG_VIDEO_SED13806
1743 Enable Epson SED13806 driver. This driver supports 8bpp
1744 and 16bpp modes defined by CONFIG_VIDEO_SED13806_8BPP
1745 or CONFIG_VIDEO_SED13806_16BPP
1748 Enable the Freescale DIU video driver. Reference boards for
1749 SOCs that have a DIU should define this macro to enable DIU
1750 support, and should also define these other macros:
1756 CONFIG_VIDEO_SW_CURSOR
1757 CONFIG_VGA_AS_SINGLE_DEVICE
1759 CONFIG_VIDEO_BMP_LOGO
1761 The DIU driver will look for the 'video-mode' environment
1762 variable, and if defined, enable the DIU as a console during
1763 boot. See the documentation file README.video for a
1764 description of this variable.
1768 Enable the VGA video / BIOS for x86. The alternative if you
1769 are using coreboot is to use the coreboot frame buffer
1776 Define this to enable a custom keyboard support.
1777 This simply calls drv_keyboard_init() which must be
1778 defined in your board-specific files.
1779 The only board using this so far is RBC823.
1781 - LCD Support: CONFIG_LCD
1783 Define this to enable LCD support (for output to LCD
1784 display); also select one of the supported displays
1785 by defining one of these:
1789 HITACHI TX09D70VM1CCA, 3.5", 240x320.
1791 CONFIG_NEC_NL6448AC33:
1793 NEC NL6448AC33-18. Active, color, single scan.
1795 CONFIG_NEC_NL6448BC20
1797 NEC NL6448BC20-08. 6.5", 640x480.
1798 Active, color, single scan.
1800 CONFIG_NEC_NL6448BC33_54
1802 NEC NL6448BC33-54. 10.4", 640x480.
1803 Active, color, single scan.
1807 Sharp 320x240. Active, color, single scan.
1808 It isn't 16x9, and I am not sure what it is.
1810 CONFIG_SHARP_LQ64D341
1812 Sharp LQ64D341 display, 640x480.
1813 Active, color, single scan.
1817 HLD1045 display, 640x480.
1818 Active, color, single scan.
1822 Optrex CBL50840-2 NF-FW 99 22 M5
1824 Hitachi LMG6912RPFC-00T
1828 320x240. Black & white.
1830 Normally display is black on white background; define
1831 CONFIG_SYS_WHITE_ON_BLACK to get it inverted.
1833 CONFIG_LCD_ALIGNMENT
1835 Normally the LCD is page-aligned (tyically 4KB). If this is
1836 defined then the LCD will be aligned to this value instead.
1837 For ARM it is sometimes useful to use MMU_SECTION_SIZE
1838 here, since it is cheaper to change data cache settings on
1839 a per-section basis.
1841 CONFIG_CONSOLE_SCROLL_LINES
1843 When the console need to be scrolled, this is the number of
1844 lines to scroll by. It defaults to 1. Increasing this makes
1845 the console jump but can help speed up operation when scrolling
1850 Support drawing of RLE8-compressed bitmaps on the LCD.
1854 Enables an 'i2c edid' command which can read EDID
1855 information over I2C from an attached LCD display.
1857 - Splash Screen Support: CONFIG_SPLASH_SCREEN
1859 If this option is set, the environment is checked for
1860 a variable "splashimage". If found, the usual display
1861 of logo, copyright and system information on the LCD
1862 is suppressed and the BMP image at the address
1863 specified in "splashimage" is loaded instead. The
1864 console is redirected to the "nulldev", too. This
1865 allows for a "silent" boot where a splash screen is
1866 loaded very quickly after power-on.
1868 CONFIG_SPLASHIMAGE_GUARD
1870 If this option is set, then U-Boot will prevent the environment
1871 variable "splashimage" from being set to a problematic address
1872 (see README.displaying-bmps).
1873 This option is useful for targets where, due to alignment
1874 restrictions, an improperly aligned BMP image will cause a data
1875 abort. If you think you will not have problems with unaligned
1876 accesses (for example because your toolchain prevents them)
1877 there is no need to set this option.
1879 CONFIG_SPLASH_SCREEN_ALIGN
1881 If this option is set the splash image can be freely positioned
1882 on the screen. Environment variable "splashpos" specifies the
1883 position as "x,y". If a positive number is given it is used as
1884 number of pixel from left/top. If a negative number is given it
1885 is used as number of pixel from right/bottom. You can also
1886 specify 'm' for centering the image.
1889 setenv splashpos m,m
1890 => image at center of screen
1892 setenv splashpos 30,20
1893 => image at x = 30 and y = 20
1895 setenv splashpos -10,m
1896 => vertically centered image
1897 at x = dspWidth - bmpWidth - 9
1899 - Gzip compressed BMP image support: CONFIG_VIDEO_BMP_GZIP
1901 If this option is set, additionally to standard BMP
1902 images, gzipped BMP images can be displayed via the
1903 splashscreen support or the bmp command.
1905 - Run length encoded BMP image (RLE8) support: CONFIG_VIDEO_BMP_RLE8
1907 If this option is set, 8-bit RLE compressed BMP images
1908 can be displayed via the splashscreen support or the
1911 - Do compresssing for memory range:
1914 If this option is set, it would use zlib deflate method
1915 to compress the specified memory at its best effort.
1917 - Compression support:
1920 Enabled by default to support gzip compressed images.
1924 If this option is set, support for bzip2 compressed
1925 images is included. If not, only uncompressed and gzip
1926 compressed images are supported.
1928 NOTE: the bzip2 algorithm requires a lot of RAM, so
1929 the malloc area (as defined by CONFIG_SYS_MALLOC_LEN) should
1934 If this option is set, support for lzma compressed
1937 Note: The LZMA algorithm adds between 2 and 4KB of code and it
1938 requires an amount of dynamic memory that is given by the
1941 (1846 + 768 << (lc + lp)) * sizeof(uint16)
1943 Where lc and lp stand for, respectively, Literal context bits
1944 and Literal pos bits.
1946 This value is upper-bounded by 14MB in the worst case. Anyway,
1947 for a ~4MB large kernel image, we have lc=3 and lp=0 for a
1948 total amount of (1846 + 768 << (3 + 0)) * 2 = ~41KB... that is
1949 a very small buffer.
1951 Use the lzmainfo tool to determinate the lc and lp values and
1952 then calculate the amount of needed dynamic memory (ensuring
1953 the appropriate CONFIG_SYS_MALLOC_LEN value).
1957 If this option is set, support for LZO compressed images
1963 The address of PHY on MII bus.
1965 CONFIG_PHY_CLOCK_FREQ (ppc4xx)
1967 The clock frequency of the MII bus
1971 If this option is set, support for speed/duplex
1972 detection of gigabit PHY is included.
1974 CONFIG_PHY_RESET_DELAY
1976 Some PHY like Intel LXT971A need extra delay after
1977 reset before any MII register access is possible.
1978 For such PHY, set this option to the usec delay
1979 required. (minimum 300usec for LXT971A)
1981 CONFIG_PHY_CMD_DELAY (ppc4xx)
1983 Some PHY like Intel LXT971A need extra delay after
1984 command issued before MII status register can be read
1994 Define a default value for Ethernet address to use
1995 for the respective Ethernet interface, in case this
1996 is not determined automatically.
2001 Define a default value for the IP address to use for
2002 the default Ethernet interface, in case this is not
2003 determined through e.g. bootp.
2004 (Environment variable "ipaddr")
2006 - Server IP address:
2009 Defines a default value for the IP address of a TFTP
2010 server to contact when using the "tftboot" command.
2011 (Environment variable "serverip")
2013 CONFIG_KEEP_SERVERADDR
2015 Keeps the server's MAC address, in the env 'serveraddr'
2016 for passing to bootargs (like Linux's netconsole option)
2018 - Gateway IP address:
2021 Defines a default value for the IP address of the
2022 default router where packets to other networks are
2024 (Environment variable "gatewayip")
2029 Defines a default value for the subnet mask (or
2030 routing prefix) which is used to determine if an IP
2031 address belongs to the local subnet or needs to be
2032 forwarded through a router.
2033 (Environment variable "netmask")
2035 - Multicast TFTP Mode:
2038 Defines whether you want to support multicast TFTP as per
2039 rfc-2090; for example to work with atftp. Lets lots of targets
2040 tftp down the same boot image concurrently. Note: the Ethernet
2041 driver in use must provide a function: mcast() to join/leave a
2044 - BOOTP Recovery Mode:
2045 CONFIG_BOOTP_RANDOM_DELAY
2047 If you have many targets in a network that try to
2048 boot using BOOTP, you may want to avoid that all
2049 systems send out BOOTP requests at precisely the same
2050 moment (which would happen for instance at recovery
2051 from a power failure, when all systems will try to
2052 boot, thus flooding the BOOTP server. Defining
2053 CONFIG_BOOTP_RANDOM_DELAY causes a random delay to be
2054 inserted before sending out BOOTP requests. The
2055 following delays are inserted then:
2057 1st BOOTP request: delay 0 ... 1 sec
2058 2nd BOOTP request: delay 0 ... 2 sec
2059 3rd BOOTP request: delay 0 ... 4 sec
2061 BOOTP requests: delay 0 ... 8 sec
2063 CONFIG_BOOTP_ID_CACHE_SIZE
2065 BOOTP packets are uniquely identified using a 32-bit ID. The
2066 server will copy the ID from client requests to responses and
2067 U-Boot will use this to determine if it is the destination of
2068 an incoming response. Some servers will check that addresses
2069 aren't in use before handing them out (usually using an ARP
2070 ping) and therefore take up to a few hundred milliseconds to
2071 respond. Network congestion may also influence the time it
2072 takes for a response to make it back to the client. If that
2073 time is too long, U-Boot will retransmit requests. In order
2074 to allow earlier responses to still be accepted after these
2075 retransmissions, U-Boot's BOOTP client keeps a small cache of
2076 IDs. The CONFIG_BOOTP_ID_CACHE_SIZE controls the size of this
2077 cache. The default is to keep IDs for up to four outstanding
2078 requests. Increasing this will allow U-Boot to accept offers
2079 from a BOOTP client in networks with unusually high latency.
2081 - DHCP Advanced Options:
2082 You can fine tune the DHCP functionality by defining
2083 CONFIG_BOOTP_* symbols:
2085 CONFIG_BOOTP_SUBNETMASK
2086 CONFIG_BOOTP_GATEWAY
2087 CONFIG_BOOTP_HOSTNAME
2088 CONFIG_BOOTP_NISDOMAIN
2089 CONFIG_BOOTP_BOOTPATH
2090 CONFIG_BOOTP_BOOTFILESIZE
2093 CONFIG_BOOTP_SEND_HOSTNAME
2094 CONFIG_BOOTP_NTPSERVER
2095 CONFIG_BOOTP_TIMEOFFSET
2096 CONFIG_BOOTP_VENDOREX
2097 CONFIG_BOOTP_MAY_FAIL
2099 CONFIG_BOOTP_SERVERIP - TFTP server will be the serverip
2100 environment variable, not the BOOTP server.
2102 CONFIG_BOOTP_MAY_FAIL - If the DHCP server is not found
2103 after the configured retry count, the call will fail
2104 instead of starting over. This can be used to fail over
2105 to Link-local IP address configuration if the DHCP server
2108 CONFIG_BOOTP_DNS2 - If a DHCP client requests the DNS
2109 serverip from a DHCP server, it is possible that more
2110 than one DNS serverip is offered to the client.
2111 If CONFIG_BOOTP_DNS2 is enabled, the secondary DNS
2112 serverip will be stored in the additional environment
2113 variable "dnsip2". The first DNS serverip is always
2114 stored in the variable "dnsip", when CONFIG_BOOTP_DNS
2117 CONFIG_BOOTP_SEND_HOSTNAME - Some DHCP servers are capable
2118 to do a dynamic update of a DNS server. To do this, they
2119 need the hostname of the DHCP requester.
2120 If CONFIG_BOOTP_SEND_HOSTNAME is defined, the content
2121 of the "hostname" environment variable is passed as
2122 option 12 to the DHCP server.
2124 CONFIG_BOOTP_DHCP_REQUEST_DELAY
2126 A 32bit value in microseconds for a delay between
2127 receiving a "DHCP Offer" and sending the "DHCP Request".
2128 This fixes a problem with certain DHCP servers that don't
2129 respond 100% of the time to a "DHCP request". E.g. On an
2130 AT91RM9200 processor running at 180MHz, this delay needed
2131 to be *at least* 15,000 usec before a Windows Server 2003
2132 DHCP server would reply 100% of the time. I recommend at
2133 least 50,000 usec to be safe. The alternative is to hope
2134 that one of the retries will be successful but note that
2135 the DHCP timeout and retry process takes a longer than
2138 - Link-local IP address negotiation:
2139 Negotiate with other link-local clients on the local network
2140 for an address that doesn't require explicit configuration.
2141 This is especially useful if a DHCP server cannot be guaranteed
2142 to exist in all environments that the device must operate.
2144 See doc/README.link-local for more information.
2147 CONFIG_CDP_DEVICE_ID
2149 The device id used in CDP trigger frames.
2151 CONFIG_CDP_DEVICE_ID_PREFIX
2153 A two character string which is prefixed to the MAC address
2158 A printf format string which contains the ascii name of
2159 the port. Normally is set to "eth%d" which sets
2160 eth0 for the first Ethernet, eth1 for the second etc.
2162 CONFIG_CDP_CAPABILITIES
2164 A 32bit integer which indicates the device capabilities;
2165 0x00000010 for a normal host which does not forwards.
2169 An ascii string containing the version of the software.
2173 An ascii string containing the name of the platform.
2177 A 32bit integer sent on the trigger.
2179 CONFIG_CDP_POWER_CONSUMPTION
2181 A 16bit integer containing the power consumption of the
2182 device in .1 of milliwatts.
2184 CONFIG_CDP_APPLIANCE_VLAN_TYPE
2186 A byte containing the id of the VLAN.
2188 - Status LED: CONFIG_STATUS_LED
2190 Several configurations allow to display the current
2191 status using a LED. For instance, the LED will blink
2192 fast while running U-Boot code, stop blinking as
2193 soon as a reply to a BOOTP request was received, and
2194 start blinking slow once the Linux kernel is running
2195 (supported by a status LED driver in the Linux
2196 kernel). Defining CONFIG_STATUS_LED enables this
2202 The status LED can be connected to a GPIO pin.
2203 In such cases, the gpio_led driver can be used as a
2204 status LED backend implementation. Define CONFIG_GPIO_LED
2205 to include the gpio_led driver in the U-Boot binary.
2207 CONFIG_GPIO_LED_INVERTED_TABLE
2208 Some GPIO connected LEDs may have inverted polarity in which
2209 case the GPIO high value corresponds to LED off state and
2210 GPIO low value corresponds to LED on state.
2211 In such cases CONFIG_GPIO_LED_INVERTED_TABLE may be defined
2212 with a list of GPIO LEDs that have inverted polarity.
2214 - CAN Support: CONFIG_CAN_DRIVER
2216 Defining CONFIG_CAN_DRIVER enables CAN driver support
2217 on those systems that support this (optional)
2218 feature, like the TQM8xxL modules.
2220 - I2C Support: CONFIG_SYS_I2C
2222 This enable the NEW i2c subsystem, and will allow you to use
2223 i2c commands at the u-boot command line (as long as you set
2224 CONFIG_CMD_I2C in CONFIG_COMMANDS) and communicate with i2c
2225 based realtime clock chips or other i2c devices. See
2226 common/cmd_i2c.c for a description of the command line
2229 ported i2c driver to the new framework:
2230 - drivers/i2c/soft_i2c.c:
2231 - activate first bus with CONFIG_SYS_I2C_SOFT define
2232 CONFIG_SYS_I2C_SOFT_SPEED and CONFIG_SYS_I2C_SOFT_SLAVE
2233 for defining speed and slave address
2234 - activate second bus with I2C_SOFT_DECLARATIONS2 define
2235 CONFIG_SYS_I2C_SOFT_SPEED_2 and CONFIG_SYS_I2C_SOFT_SLAVE_2
2236 for defining speed and slave address
2237 - activate third bus with I2C_SOFT_DECLARATIONS3 define
2238 CONFIG_SYS_I2C_SOFT_SPEED_3 and CONFIG_SYS_I2C_SOFT_SLAVE_3
2239 for defining speed and slave address
2240 - activate fourth bus with I2C_SOFT_DECLARATIONS4 define
2241 CONFIG_SYS_I2C_SOFT_SPEED_4 and CONFIG_SYS_I2C_SOFT_SLAVE_4
2242 for defining speed and slave address
2244 - drivers/i2c/fsl_i2c.c:
2245 - activate i2c driver with CONFIG_SYS_I2C_FSL
2246 define CONFIG_SYS_FSL_I2C_OFFSET for setting the register
2247 offset CONFIG_SYS_FSL_I2C_SPEED for the i2c speed and
2248 CONFIG_SYS_FSL_I2C_SLAVE for the slave addr of the first
2250 - If your board supports a second fsl i2c bus, define
2251 CONFIG_SYS_FSL_I2C2_OFFSET for the register offset
2252 CONFIG_SYS_FSL_I2C2_SPEED for the speed and
2253 CONFIG_SYS_FSL_I2C2_SLAVE for the slave address of the
2256 - drivers/i2c/tegra_i2c.c:
2257 - activate this driver with CONFIG_SYS_I2C_TEGRA
2258 - This driver adds 4 i2c buses with a fix speed from
2259 100000 and the slave addr 0!
2261 - drivers/i2c/ppc4xx_i2c.c
2262 - activate this driver with CONFIG_SYS_I2C_PPC4XX
2263 - CONFIG_SYS_I2C_PPC4XX_CH0 activate hardware channel 0
2264 - CONFIG_SYS_I2C_PPC4XX_CH1 activate hardware channel 1
2266 - drivers/i2c/i2c_mxc.c
2267 - activate this driver with CONFIG_SYS_I2C_MXC
2268 - define speed for bus 1 with CONFIG_SYS_MXC_I2C1_SPEED
2269 - define slave for bus 1 with CONFIG_SYS_MXC_I2C1_SLAVE
2270 - define speed for bus 2 with CONFIG_SYS_MXC_I2C2_SPEED
2271 - define slave for bus 2 with CONFIG_SYS_MXC_I2C2_SLAVE
2272 - define speed for bus 3 with CONFIG_SYS_MXC_I2C3_SPEED
2273 - define slave for bus 3 with CONFIG_SYS_MXC_I2C3_SLAVE
2274 If thoses defines are not set, default value is 100000
2275 for speed, and 0 for slave.
2277 - drivers/i2c/rcar_i2c.c:
2278 - activate this driver with CONFIG_SYS_I2C_RCAR
2279 - This driver adds 4 i2c buses
2281 - CONFIG_SYS_RCAR_I2C0_BASE for setting the register channel 0
2282 - CONFIG_SYS_RCAR_I2C0_SPEED for for the speed channel 0
2283 - CONFIG_SYS_RCAR_I2C1_BASE for setting the register channel 1
2284 - CONFIG_SYS_RCAR_I2C1_SPEED for for the speed channel 1
2285 - CONFIG_SYS_RCAR_I2C2_BASE for setting the register channel 2
2286 - CONFIG_SYS_RCAR_I2C2_SPEED for for the speed channel 2
2287 - CONFIG_SYS_RCAR_I2C3_BASE for setting the register channel 3
2288 - CONFIG_SYS_RCAR_I2C3_SPEED for for the speed channel 3
2289 - CONFIF_SYS_RCAR_I2C_NUM_CONTROLLERS for number of i2c buses
2291 - drivers/i2c/sh_i2c.c:
2292 - activate this driver with CONFIG_SYS_I2C_SH
2293 - This driver adds from 2 to 5 i2c buses
2295 - CONFIG_SYS_I2C_SH_BASE0 for setting the register channel 0
2296 - CONFIG_SYS_I2C_SH_SPEED0 for for the speed channel 0
2297 - CONFIG_SYS_I2C_SH_BASE1 for setting the register channel 1
2298 - CONFIG_SYS_I2C_SH_SPEED1 for for the speed channel 1
2299 - CONFIG_SYS_I2C_SH_BASE2 for setting the register channel 2
2300 - CONFIG_SYS_I2C_SH_SPEED2 for for the speed channel 2
2301 - CONFIG_SYS_I2C_SH_BASE3 for setting the register channel 3
2302 - CONFIG_SYS_I2C_SH_SPEED3 for for the speed channel 3
2303 - CONFIG_SYS_I2C_SH_BASE4 for setting the register channel 4
2304 - CONFIG_SYS_I2C_SH_SPEED4 for for the speed channel 4
2305 - CONFIG_SYS_I2C_SH_BASE5 for setting the register channel 5
2306 - CONFIG_SYS_I2C_SH_SPEED5 for for the speed channel 5
2307 - CONFIF_SYS_I2C_SH_NUM_CONTROLLERS for nummber of i2c buses
2309 - drivers/i2c/omap24xx_i2c.c
2310 - activate this driver with CONFIG_SYS_I2C_OMAP24XX
2311 - CONFIG_SYS_OMAP24_I2C_SPEED speed channel 0
2312 - CONFIG_SYS_OMAP24_I2C_SLAVE slave addr channel 0
2313 - CONFIG_SYS_OMAP24_I2C_SPEED1 speed channel 1
2314 - CONFIG_SYS_OMAP24_I2C_SLAVE1 slave addr channel 1
2315 - CONFIG_SYS_OMAP24_I2C_SPEED2 speed channel 2
2316 - CONFIG_SYS_OMAP24_I2C_SLAVE2 slave addr channel 2
2317 - CONFIG_SYS_OMAP24_I2C_SPEED3 speed channel 3
2318 - CONFIG_SYS_OMAP24_I2C_SLAVE3 slave addr channel 3
2319 - CONFIG_SYS_OMAP24_I2C_SPEED4 speed channel 4
2320 - CONFIG_SYS_OMAP24_I2C_SLAVE4 slave addr channel 4
2322 - drivers/i2c/zynq_i2c.c
2323 - activate this driver with CONFIG_SYS_I2C_ZYNQ
2324 - set CONFIG_SYS_I2C_ZYNQ_SPEED for speed setting
2325 - set CONFIG_SYS_I2C_ZYNQ_SLAVE for slave addr
2327 - drivers/i2c/s3c24x0_i2c.c:
2328 - activate this driver with CONFIG_SYS_I2C_S3C24X0
2329 - This driver adds i2c buses (11 for Exynos5250, Exynos5420
2330 9 i2c buses for Exynos4 and 1 for S3C24X0 SoCs from Samsung)
2331 with a fix speed from 100000 and the slave addr 0!
2333 - drivers/i2c/ihs_i2c.c
2334 - activate this driver with CONFIG_SYS_I2C_IHS
2335 - CONFIG_SYS_I2C_IHS_CH0 activate hardware channel 0
2336 - CONFIG_SYS_I2C_IHS_SPEED_0 speed channel 0
2337 - CONFIG_SYS_I2C_IHS_SLAVE_0 slave addr channel 0
2338 - CONFIG_SYS_I2C_IHS_CH1 activate hardware channel 1
2339 - CONFIG_SYS_I2C_IHS_SPEED_1 speed channel 1
2340 - CONFIG_SYS_I2C_IHS_SLAVE_1 slave addr channel 1
2341 - CONFIG_SYS_I2C_IHS_CH2 activate hardware channel 2
2342 - CONFIG_SYS_I2C_IHS_SPEED_2 speed channel 2
2343 - CONFIG_SYS_I2C_IHS_SLAVE_2 slave addr channel 2
2344 - CONFIG_SYS_I2C_IHS_CH3 activate hardware channel 3
2345 - CONFIG_SYS_I2C_IHS_SPEED_3 speed channel 3
2346 - CONFIG_SYS_I2C_IHS_SLAVE_3 slave addr channel 3
2350 CONFIG_SYS_NUM_I2C_BUSES
2351 Hold the number of i2c busses you want to use. If you
2352 don't use/have i2c muxes on your i2c bus, this
2353 is equal to CONFIG_SYS_NUM_I2C_ADAPTERS, and you can
2356 CONFIG_SYS_I2C_DIRECT_BUS
2357 define this, if you don't use i2c muxes on your hardware.
2358 if CONFIG_SYS_I2C_MAX_HOPS is not defined or == 0 you can
2361 CONFIG_SYS_I2C_MAX_HOPS
2362 define how many muxes are maximal consecutively connected
2363 on one i2c bus. If you not use i2c muxes, omit this
2366 CONFIG_SYS_I2C_BUSES
2367 hold a list of busses you want to use, only used if
2368 CONFIG_SYS_I2C_DIRECT_BUS is not defined, for example
2369 a board with CONFIG_SYS_I2C_MAX_HOPS = 1 and
2370 CONFIG_SYS_NUM_I2C_BUSES = 9:
2372 CONFIG_SYS_I2C_BUSES {{0, {I2C_NULL_HOP}}, \
2373 {0, {{I2C_MUX_PCA9547, 0x70, 1}}}, \
2374 {0, {{I2C_MUX_PCA9547, 0x70, 2}}}, \
2375 {0, {{I2C_MUX_PCA9547, 0x70, 3}}}, \
2376 {0, {{I2C_MUX_PCA9547, 0x70, 4}}}, \
2377 {0, {{I2C_MUX_PCA9547, 0x70, 5}}}, \
2378 {1, {I2C_NULL_HOP}}, \
2379 {1, {{I2C_MUX_PCA9544, 0x72, 1}}}, \
2380 {1, {{I2C_MUX_PCA9544, 0x72, 2}}}, \
2384 bus 0 on adapter 0 without a mux
2385 bus 1 on adapter 0 with a PCA9547 on address 0x70 port 1
2386 bus 2 on adapter 0 with a PCA9547 on address 0x70 port 2
2387 bus 3 on adapter 0 with a PCA9547 on address 0x70 port 3
2388 bus 4 on adapter 0 with a PCA9547 on address 0x70 port 4
2389 bus 5 on adapter 0 with a PCA9547 on address 0x70 port 5
2390 bus 6 on adapter 1 without a mux
2391 bus 7 on adapter 1 with a PCA9544 on address 0x72 port 1
2392 bus 8 on adapter 1 with a PCA9544 on address 0x72 port 2
2394 If you do not have i2c muxes on your board, omit this define.
2396 - Legacy I2C Support: CONFIG_HARD_I2C
2398 NOTE: It is intended to move drivers to CONFIG_SYS_I2C which
2399 provides the following compelling advantages:
2401 - more than one i2c adapter is usable
2402 - approved multibus support
2403 - better i2c mux support
2405 ** Please consider updating your I2C driver now. **
2407 These enable legacy I2C serial bus commands. Defining
2408 CONFIG_HARD_I2C will include the appropriate I2C driver
2409 for the selected CPU.
2411 This will allow you to use i2c commands at the u-boot
2412 command line (as long as you set CONFIG_CMD_I2C in
2413 CONFIG_COMMANDS) and communicate with i2c based realtime
2414 clock chips. See common/cmd_i2c.c for a description of the
2415 command line interface.
2417 CONFIG_HARD_I2C selects a hardware I2C controller.
2419 There are several other quantities that must also be
2420 defined when you define CONFIG_HARD_I2C.
2422 In both cases you will need to define CONFIG_SYS_I2C_SPEED
2423 to be the frequency (in Hz) at which you wish your i2c bus
2424 to run and CONFIG_SYS_I2C_SLAVE to be the address of this node (ie
2425 the CPU's i2c node address).
2427 Now, the u-boot i2c code for the mpc8xx
2428 (arch/powerpc/cpu/mpc8xx/i2c.c) sets the CPU up as a master node
2429 and so its address should therefore be cleared to 0 (See,
2430 eg, MPC823e User's Manual p.16-473). So, set
2431 CONFIG_SYS_I2C_SLAVE to 0.
2433 CONFIG_SYS_I2C_INIT_MPC5XXX
2435 When a board is reset during an i2c bus transfer
2436 chips might think that the current transfer is still
2437 in progress. Reset the slave devices by sending start
2438 commands until the slave device responds.
2440 That's all that's required for CONFIG_HARD_I2C.
2442 If you use the software i2c interface (CONFIG_SYS_I2C_SOFT)
2443 then the following macros need to be defined (examples are
2444 from include/configs/lwmon.h):
2448 (Optional). Any commands necessary to enable the I2C
2449 controller or configure ports.
2451 eg: #define I2C_INIT (immr->im_cpm.cp_pbdir |= PB_SCL)
2455 (Only for MPC8260 CPU). The I/O port to use (the code
2456 assumes both bits are on the same port). Valid values
2457 are 0..3 for ports A..D.
2461 The code necessary to make the I2C data line active
2462 (driven). If the data line is open collector, this
2465 eg: #define I2C_ACTIVE (immr->im_cpm.cp_pbdir |= PB_SDA)
2469 The code necessary to make the I2C data line tri-stated
2470 (inactive). If the data line is open collector, this
2473 eg: #define I2C_TRISTATE (immr->im_cpm.cp_pbdir &= ~PB_SDA)
2477 Code that returns true if the I2C data line is high,
2480 eg: #define I2C_READ ((immr->im_cpm.cp_pbdat & PB_SDA) != 0)
2484 If <bit> is true, sets the I2C data line high. If it
2485 is false, it clears it (low).
2487 eg: #define I2C_SDA(bit) \
2488 if(bit) immr->im_cpm.cp_pbdat |= PB_SDA; \
2489 else immr->im_cpm.cp_pbdat &= ~PB_SDA
2493 If <bit> is true, sets the I2C clock line high. If it
2494 is false, it clears it (low).
2496 eg: #define I2C_SCL(bit) \
2497 if(bit) immr->im_cpm.cp_pbdat |= PB_SCL; \
2498 else immr->im_cpm.cp_pbdat &= ~PB_SCL
2502 This delay is invoked four times per clock cycle so this
2503 controls the rate of data transfer. The data rate thus
2504 is 1 / (I2C_DELAY * 4). Often defined to be something
2507 #define I2C_DELAY udelay(2)
2509 CONFIG_SOFT_I2C_GPIO_SCL / CONFIG_SOFT_I2C_GPIO_SDA
2511 If your arch supports the generic GPIO framework (asm/gpio.h),
2512 then you may alternatively define the two GPIOs that are to be
2513 used as SCL / SDA. Any of the previous I2C_xxx macros will
2514 have GPIO-based defaults assigned to them as appropriate.
2516 You should define these to the GPIO value as given directly to
2517 the generic GPIO functions.
2519 CONFIG_SYS_I2C_INIT_BOARD
2521 When a board is reset during an i2c bus transfer
2522 chips might think that the current transfer is still
2523 in progress. On some boards it is possible to access
2524 the i2c SCLK line directly, either by using the
2525 processor pin as a GPIO or by having a second pin
2526 connected to the bus. If this option is defined a
2527 custom i2c_init_board() routine in boards/xxx/board.c
2528 is run early in the boot sequence.
2530 CONFIG_SYS_I2C_BOARD_LATE_INIT
2532 An alternative to CONFIG_SYS_I2C_INIT_BOARD. If this option is
2533 defined a custom i2c_board_late_init() routine in
2534 boards/xxx/board.c is run AFTER the operations in i2c_init()
2535 is completed. This callpoint can be used to unreset i2c bus
2536 using CPU i2c controller register accesses for CPUs whose i2c
2537 controller provide such a method. It is called at the end of
2538 i2c_init() to allow i2c_init operations to setup the i2c bus
2539 controller on the CPU (e.g. setting bus speed & slave address).
2541 CONFIG_I2CFAST (PPC405GP|PPC405EP only)
2543 This option enables configuration of bi_iic_fast[] flags
2544 in u-boot bd_info structure based on u-boot environment
2545 variable "i2cfast". (see also i2cfast)
2547 CONFIG_I2C_MULTI_BUS
2549 This option allows the use of multiple I2C buses, each of which
2550 must have a controller. At any point in time, only one bus is
2551 active. To switch to a different bus, use the 'i2c dev' command.
2552 Note that bus numbering is zero-based.
2554 CONFIG_SYS_I2C_NOPROBES
2556 This option specifies a list of I2C devices that will be skipped
2557 when the 'i2c probe' command is issued. If CONFIG_I2C_MULTI_BUS
2558 is set, specify a list of bus-device pairs. Otherwise, specify
2559 a 1D array of device addresses
2562 #undef CONFIG_I2C_MULTI_BUS
2563 #define CONFIG_SYS_I2C_NOPROBES {0x50,0x68}
2565 will skip addresses 0x50 and 0x68 on a board with one I2C bus
2567 #define CONFIG_I2C_MULTI_BUS
2568 #define CONFIG_SYS_I2C_MULTI_NOPROBES {{0,0x50},{0,0x68},{1,0x54}}
2570 will skip addresses 0x50 and 0x68 on bus 0 and address 0x54 on bus 1
2572 CONFIG_SYS_SPD_BUS_NUM
2574 If defined, then this indicates the I2C bus number for DDR SPD.
2575 If not defined, then U-Boot assumes that SPD is on I2C bus 0.
2577 CONFIG_SYS_RTC_BUS_NUM
2579 If defined, then this indicates the I2C bus number for the RTC.
2580 If not defined, then U-Boot assumes that RTC is on I2C bus 0.
2582 CONFIG_SYS_DTT_BUS_NUM
2584 If defined, then this indicates the I2C bus number for the DTT.
2585 If not defined, then U-Boot assumes that DTT is on I2C bus 0.
2587 CONFIG_SYS_I2C_DTT_ADDR:
2589 If defined, specifies the I2C address of the DTT device.
2590 If not defined, then U-Boot uses predefined value for
2591 specified DTT device.
2593 CONFIG_SOFT_I2C_READ_REPEATED_START
2595 defining this will force the i2c_read() function in
2596 the soft_i2c driver to perform an I2C repeated start
2597 between writing the address pointer and reading the
2598 data. If this define is omitted the default behaviour
2599 of doing a stop-start sequence will be used. Most I2C
2600 devices can use either method, but some require one or
2603 - SPI Support: CONFIG_SPI
2605 Enables SPI driver (so far only tested with
2606 SPI EEPROM, also an instance works with Crystal A/D and
2607 D/As on the SACSng board)
2611 Enables the driver for SPI controller on SuperH. Currently
2612 only SH7757 is supported.
2616 Enables extended (16-bit) SPI EEPROM addressing.
2617 (symmetrical to CONFIG_I2C_X)
2621 Enables a software (bit-bang) SPI driver rather than
2622 using hardware support. This is a general purpose
2623 driver that only requires three general I/O port pins
2624 (two outputs, one input) to function. If this is
2625 defined, the board configuration must define several
2626 SPI configuration items (port pins to use, etc). For
2627 an example, see include/configs/sacsng.h.
2631 Enables a hardware SPI driver for general-purpose reads
2632 and writes. As with CONFIG_SOFT_SPI, the board configuration
2633 must define a list of chip-select function pointers.
2634 Currently supported on some MPC8xxx processors. For an
2635 example, see include/configs/mpc8349emds.h.
2639 Enables the driver for the SPI controllers on i.MX and MXC
2640 SoCs. Currently i.MX31/35/51 are supported.
2642 CONFIG_SYS_SPI_MXC_WAIT
2643 Timeout for waiting until spi transfer completed.
2644 default: (CONFIG_SYS_HZ/100) /* 10 ms */
2646 - FPGA Support: CONFIG_FPGA
2648 Enables FPGA subsystem.
2650 CONFIG_FPGA_<vendor>
2652 Enables support for specific chip vendors.
2655 CONFIG_FPGA_<family>
2657 Enables support for FPGA family.
2658 (SPARTAN2, SPARTAN3, VIRTEX2, CYCLONE2, ACEX1K, ACEX)
2662 Specify the number of FPGA devices to support.
2664 CONFIG_CMD_FPGA_LOADMK
2666 Enable support for fpga loadmk command
2668 CONFIG_CMD_FPGA_LOADP
2670 Enable support for fpga loadp command - load partial bitstream
2672 CONFIG_CMD_FPGA_LOADBP
2674 Enable support for fpga loadbp command - load partial bitstream
2677 CONFIG_SYS_FPGA_PROG_FEEDBACK
2679 Enable printing of hash marks during FPGA configuration.
2681 CONFIG_SYS_FPGA_CHECK_BUSY
2683 Enable checks on FPGA configuration interface busy
2684 status by the configuration function. This option
2685 will require a board or device specific function to
2690 If defined, a function that provides delays in the FPGA
2691 configuration driver.
2693 CONFIG_SYS_FPGA_CHECK_CTRLC
2694 Allow Control-C to interrupt FPGA configuration
2696 CONFIG_SYS_FPGA_CHECK_ERROR
2698 Check for configuration errors during FPGA bitfile
2699 loading. For example, abort during Virtex II
2700 configuration if the INIT_B line goes low (which
2701 indicated a CRC error).
2703 CONFIG_SYS_FPGA_WAIT_INIT
2705 Maximum time to wait for the INIT_B line to deassert
2706 after PROB_B has been deasserted during a Virtex II
2707 FPGA configuration sequence. The default time is 500
2710 CONFIG_SYS_FPGA_WAIT_BUSY
2712 Maximum time to wait for BUSY to deassert during
2713 Virtex II FPGA configuration. The default is 5 ms.
2715 CONFIG_SYS_FPGA_WAIT_CONFIG
2717 Time to wait after FPGA configuration. The default is
2720 - Configuration Management:
2723 Some SoCs need special image types (e.g. U-Boot binary
2724 with a special header) as build targets. By defining
2725 CONFIG_BUILD_TARGET in the SoC / board header, this
2726 special image will be automatically built upon calling
2731 If defined, this string will be added to the U-Boot
2732 version information (U_BOOT_VERSION)
2734 - Vendor Parameter Protection:
2736 U-Boot considers the values of the environment
2737 variables "serial#" (Board Serial Number) and
2738 "ethaddr" (Ethernet Address) to be parameters that
2739 are set once by the board vendor / manufacturer, and
2740 protects these variables from casual modification by
2741 the user. Once set, these variables are read-only,
2742 and write or delete attempts are rejected. You can
2743 change this behaviour:
2745 If CONFIG_ENV_OVERWRITE is #defined in your config
2746 file, the write protection for vendor parameters is
2747 completely disabled. Anybody can change or delete
2750 Alternatively, if you #define _both_ CONFIG_ETHADDR
2751 _and_ CONFIG_OVERWRITE_ETHADDR_ONCE, a default
2752 Ethernet address is installed in the environment,
2753 which can be changed exactly ONCE by the user. [The
2754 serial# is unaffected by this, i. e. it remains
2757 The same can be accomplished in a more flexible way
2758 for any variable by configuring the type of access
2759 to allow for those variables in the ".flags" variable
2760 or define CONFIG_ENV_FLAGS_LIST_STATIC.
2765 Define this variable to enable the reservation of
2766 "protected RAM", i. e. RAM which is not overwritten
2767 by U-Boot. Define CONFIG_PRAM to hold the number of
2768 kB you want to reserve for pRAM. You can overwrite
2769 this default value by defining an environment
2770 variable "pram" to the number of kB you want to
2771 reserve. Note that the board info structure will
2772 still show the full amount of RAM. If pRAM is
2773 reserved, a new environment variable "mem" will
2774 automatically be defined to hold the amount of
2775 remaining RAM in a form that can be passed as boot
2776 argument to Linux, for instance like that:
2778 setenv bootargs ... mem=\${mem}
2781 This way you can tell Linux not to use this memory,
2782 either, which results in a memory region that will
2783 not be affected by reboots.
2785 *WARNING* If your board configuration uses automatic
2786 detection of the RAM size, you must make sure that
2787 this memory test is non-destructive. So far, the
2788 following board configurations are known to be
2791 IVMS8, IVML24, SPD8xx, TQM8xxL,
2792 HERMES, IP860, RPXlite, LWMON,
2795 - Access to physical memory region (> 4GB)
2796 Some basic support is provided for operations on memory not
2797 normally accessible to U-Boot - e.g. some architectures
2798 support access to more than 4GB of memory on 32-bit
2799 machines using physical address extension or similar.
2800 Define CONFIG_PHYSMEM to access this basic support, which
2801 currently only supports clearing the memory.
2806 Define this variable to stop the system in case of a
2807 fatal error, so that you have to reset it manually.
2808 This is probably NOT a good idea for an embedded
2809 system where you want the system to reboot
2810 automatically as fast as possible, but it may be
2811 useful during development since you can try to debug
2812 the conditions that lead to the situation.
2814 CONFIG_NET_RETRY_COUNT
2816 This variable defines the number of retries for
2817 network operations like ARP, RARP, TFTP, or BOOTP
2818 before giving up the operation. If not defined, a
2819 default value of 5 is used.
2823 Timeout waiting for an ARP reply in milliseconds.
2827 Timeout in milliseconds used in NFS protocol.
2828 If you encounter "ERROR: Cannot umount" in nfs command,
2829 try longer timeout such as
2830 #define CONFIG_NFS_TIMEOUT 10000UL
2832 - Command Interpreter:
2833 CONFIG_AUTO_COMPLETE
2835 Enable auto completion of commands using TAB.
2837 CONFIG_SYS_HUSH_PARSER
2839 Define this variable to enable the "hush" shell (from
2840 Busybox) as command line interpreter, thus enabling
2841 powerful command line syntax like
2842 if...then...else...fi conditionals or `&&' and '||'
2843 constructs ("shell scripts").
2845 If undefined, you get the old, much simpler behaviour
2846 with a somewhat smaller memory footprint.
2849 CONFIG_SYS_PROMPT_HUSH_PS2
2851 This defines the secondary prompt string, which is
2852 printed when the command interpreter needs more input
2853 to complete a command. Usually "> ".
2857 In the current implementation, the local variables
2858 space and global environment variables space are
2859 separated. Local variables are those you define by
2860 simply typing `name=value'. To access a local
2861 variable later on, you have write `$name' or
2862 `${name}'; to execute the contents of a variable
2863 directly type `$name' at the command prompt.
2865 Global environment variables are those you use
2866 setenv/printenv to work with. To run a command stored
2867 in such a variable, you need to use the run command,
2868 and you must not use the '$' sign to access them.
2870 To store commands and special characters in a
2871 variable, please use double quotation marks
2872 surrounding the whole text of the variable, instead
2873 of the backslashes before semicolons and special
2876 - Commandline Editing and History:
2877 CONFIG_CMDLINE_EDITING
2879 Enable editing and History functions for interactive
2880 commandline input operations
2882 - Default Environment:
2883 CONFIG_EXTRA_ENV_SETTINGS
2885 Define this to contain any number of null terminated
2886 strings (variable = value pairs) that will be part of
2887 the default environment compiled into the boot image.
2889 For example, place something like this in your
2890 board's config file:
2892 #define CONFIG_EXTRA_ENV_SETTINGS \
2896 Warning: This method is based on knowledge about the
2897 internal format how the environment is stored by the
2898 U-Boot code. This is NOT an official, exported
2899 interface! Although it is unlikely that this format
2900 will change soon, there is no guarantee either.
2901 You better know what you are doing here.
2903 Note: overly (ab)use of the default environment is
2904 discouraged. Make sure to check other ways to preset
2905 the environment like the "source" command or the
2908 CONFIG_ENV_VARS_UBOOT_CONFIG
2910 Define this in order to add variables describing the
2911 U-Boot build configuration to the default environment.
2912 These will be named arch, cpu, board, vendor, and soc.
2914 Enabling this option will cause the following to be defined:
2922 CONFIG_ENV_VARS_UBOOT_RUNTIME_CONFIG
2924 Define this in order to add variables describing certain
2925 run-time determined information about the hardware to the
2926 environment. These will be named board_name, board_rev.
2928 CONFIG_DELAY_ENVIRONMENT
2930 Normally the environment is loaded when the board is
2931 intialised so that it is available to U-Boot. This inhibits
2932 that so that the environment is not available until
2933 explicitly loaded later by U-Boot code. With CONFIG_OF_CONTROL
2934 this is instead controlled by the value of
2935 /config/load-environment.
2937 - DataFlash Support:
2938 CONFIG_HAS_DATAFLASH
2940 Defining this option enables DataFlash features and
2941 allows to read/write in Dataflash via the standard
2944 - Serial Flash support
2947 Defining this option enables SPI flash commands
2948 'sf probe/read/write/erase/update'.
2950 Usage requires an initial 'probe' to define the serial
2951 flash parameters, followed by read/write/erase/update
2954 The following defaults may be provided by the platform
2955 to handle the common case when only a single serial
2956 flash is present on the system.
2958 CONFIG_SF_DEFAULT_BUS Bus identifier
2959 CONFIG_SF_DEFAULT_CS Chip-select
2960 CONFIG_SF_DEFAULT_MODE (see include/spi.h)
2961 CONFIG_SF_DEFAULT_SPEED in Hz
2965 Define this option to include a destructive SPI flash
2968 CONFIG_SPI_FLASH_BAR Ban/Extended Addr Reg
2970 Define this option to use the Bank addr/Extended addr
2971 support on SPI flashes which has size > 16Mbytes.
2973 CONFIG_SF_DUAL_FLASH Dual flash memories
2975 Define this option to use dual flash support where two flash
2976 memories can be connected with a given cs line.
2977 currently Xilinx Zynq qspi support these type of connections.
2979 CONFIG_SYS_SPI_ST_ENABLE_WP_PIN
2980 enable the W#/Vpp signal to disable writing to the status
2981 register on ST MICRON flashes like the N25Q128.
2982 The status register write enable/disable bit, combined with
2983 the W#/VPP signal provides hardware data protection for the
2984 device as follows: When the enable/disable bit is set to 1,
2985 and the W#/VPP signal is driven LOW, the status register
2986 nonvolatile bits become read-only and the WRITE STATUS REGISTER
2987 operation will not execute. The only way to exit this
2988 hardware-protected mode is to drive W#/VPP HIGH.
2990 - SystemACE Support:
2993 Adding this option adds support for Xilinx SystemACE
2994 chips attached via some sort of local bus. The address
2995 of the chip must also be defined in the
2996 CONFIG_SYS_SYSTEMACE_BASE macro. For example:
2998 #define CONFIG_SYSTEMACE
2999 #define CONFIG_SYS_SYSTEMACE_BASE 0xf0000000
3001 When SystemACE support is added, the "ace" device type
3002 becomes available to the fat commands, i.e. fatls.
3004 - TFTP Fixed UDP Port:
3007 If this is defined, the environment variable tftpsrcp
3008 is used to supply the TFTP UDP source port value.
3009 If tftpsrcp isn't defined, the normal pseudo-random port
3010 number generator is used.
3012 Also, the environment variable tftpdstp is used to supply
3013 the TFTP UDP destination port value. If tftpdstp isn't
3014 defined, the normal port 69 is used.
3016 The purpose for tftpsrcp is to allow a TFTP server to
3017 blindly start the TFTP transfer using the pre-configured
3018 target IP address and UDP port. This has the effect of
3019 "punching through" the (Windows XP) firewall, allowing
3020 the remainder of the TFTP transfer to proceed normally.
3021 A better solution is to properly configure the firewall,
3022 but sometimes that is not allowed.
3027 This enables a generic 'hash' command which can produce
3028 hashes / digests from a few algorithms (e.g. SHA1, SHA256).
3032 Enable the hash verify command (hash -v). This adds to code
3035 CONFIG_SHA1 - support SHA1 hashing
3036 CONFIG_SHA256 - support SHA256 hashing
3038 Note: There is also a sha1sum command, which should perhaps
3039 be deprecated in favour of 'hash sha1'.
3041 - Freescale i.MX specific commands:
3042 CONFIG_CMD_HDMIDETECT
3043 This enables 'hdmidet' command which returns true if an
3044 HDMI monitor is detected. This command is i.MX 6 specific.
3047 This enables the 'bmode' (bootmode) command for forcing
3048 a boot from specific media.
3050 This is useful for forcing the ROM's usb downloader to
3051 activate upon a watchdog reset which is nice when iterating
3052 on U-Boot. Using the reset button or running bmode normal
3053 will set it back to normal. This command currently
3054 supports i.MX53 and i.MX6.
3059 This enables the RSA algorithm used for FIT image verification
3060 in U-Boot. See doc/uImage.FIT/signature.txt for more information.
3062 The signing part is build into mkimage regardless of this
3065 - bootcount support:
3066 CONFIG_BOOTCOUNT_LIMIT
3068 This enables the bootcounter support, see:
3069 http://www.denx.de/wiki/DULG/UBootBootCountLimit
3072 enable special bootcounter support on at91sam9xe based boards.
3074 enable special bootcounter support on blackfin based boards.
3076 enable special bootcounter support on da850 based boards.
3077 CONFIG_BOOTCOUNT_RAM
3078 enable support for the bootcounter in RAM
3079 CONFIG_BOOTCOUNT_I2C
3080 enable support for the bootcounter on an i2c (like RTC) device.
3081 CONFIG_SYS_I2C_RTC_ADDR = i2c chip address
3082 CONFIG_SYS_BOOTCOUNT_ADDR = i2c addr which is used for
3084 CONFIG_BOOTCOUNT_ALEN = address len
3086 - Show boot progress:
3087 CONFIG_SHOW_BOOT_PROGRESS
3089 Defining this option allows to add some board-
3090 specific code (calling a user-provided function
3091 "show_boot_progress(int)") that enables you to show
3092 the system's boot progress on some display (for
3093 example, some LED's) on your board. At the moment,
3094 the following checkpoints are implemented:
3096 - Detailed boot stage timing
3098 Define this option to get detailed timing of each stage
3099 of the boot process.
3101 CONFIG_BOOTSTAGE_USER_COUNT
3102 This is the number of available user bootstage records.
3103 Each time you call bootstage_mark(BOOTSTAGE_ID_ALLOC, ...)
3104 a new ID will be allocated from this stash. If you exceed
3105 the limit, recording will stop.
3107 CONFIG_BOOTSTAGE_REPORT
3108 Define this to print a report before boot, similar to this:
3110 Timer summary in microseconds:
3113 3,575,678 3,575,678 board_init_f start
3114 3,575,695 17 arch_cpu_init A9
3115 3,575,777 82 arch_cpu_init done
3116 3,659,598 83,821 board_init_r start
3117 3,910,375 250,777 main_loop
3118 29,916,167 26,005,792 bootm_start
3119 30,361,327 445,160 start_kernel
3121 CONFIG_CMD_BOOTSTAGE
3122 Add a 'bootstage' command which supports printing a report
3123 and un/stashing of bootstage data.
3125 CONFIG_BOOTSTAGE_FDT
3126 Stash the bootstage information in the FDT. A root 'bootstage'
3127 node is created with each bootstage id as a child. Each child
3128 has a 'name' property and either 'mark' containing the
3129 mark time in microsecond, or 'accum' containing the
3130 accumulated time for that bootstage id in microseconds.
3135 name = "board_init_f";
3144 Code in the Linux kernel can find this in /proc/devicetree.
3146 Legacy uImage format:
3149 1 common/cmd_bootm.c before attempting to boot an image
3150 -1 common/cmd_bootm.c Image header has bad magic number
3151 2 common/cmd_bootm.c Image header has correct magic number
3152 -2 common/cmd_bootm.c Image header has bad checksum
3153 3 common/cmd_bootm.c Image header has correct checksum
3154 -3 common/cmd_bootm.c Image data has bad checksum
3155 4 common/cmd_bootm.c Image data has correct checksum
3156 -4 common/cmd_bootm.c Image is for unsupported architecture
3157 5 common/cmd_bootm.c Architecture check OK
3158 -5 common/cmd_bootm.c Wrong Image Type (not kernel, multi)
3159 6 common/cmd_bootm.c Image Type check OK
3160 -6 common/cmd_bootm.c gunzip uncompression error
3161 -7 common/cmd_bootm.c Unimplemented compression type
3162 7 common/cmd_bootm.c Uncompression OK
3163 8 common/cmd_bootm.c No uncompress/copy overwrite error
3164 -9 common/cmd_bootm.c Unsupported OS (not Linux, BSD, VxWorks, QNX)
3166 9 common/image.c Start initial ramdisk verification
3167 -10 common/image.c Ramdisk header has bad magic number
3168 -11 common/image.c Ramdisk header has bad checksum
3169 10 common/image.c Ramdisk header is OK
3170 -12 common/image.c Ramdisk data has bad checksum
3171 11 common/image.c Ramdisk data has correct checksum
3172 12 common/image.c Ramdisk verification complete, start loading
3173 -13 common/image.c Wrong Image Type (not PPC Linux ramdisk)
3174 13 common/image.c Start multifile image verification
3175 14 common/image.c No initial ramdisk, no multifile, continue.
3177 15 arch/<arch>/lib/bootm.c All preparation done, transferring control to OS
3179 -30 arch/powerpc/lib/board.c Fatal error, hang the system
3180 -31 post/post.c POST test failed, detected by post_output_backlog()
3181 -32 post/post.c POST test failed, detected by post_run_single()
3183 34 common/cmd_doc.c before loading a Image from a DOC device
3184 -35 common/cmd_doc.c Bad usage of "doc" command
3185 35 common/cmd_doc.c correct usage of "doc" command
3186 -36 common/cmd_doc.c No boot device
3187 36 common/cmd_doc.c correct boot device
3188 -37 common/cmd_doc.c Unknown Chip ID on boot device
3189 37 common/cmd_doc.c correct chip ID found, device available
3190 -38 common/cmd_doc.c Read Error on boot device
3191 38 common/cmd_doc.c reading Image header from DOC device OK
3192 -39 common/cmd_doc.c Image header has bad magic number
3193 39 common/cmd_doc.c Image header has correct magic number
3194 -40 common/cmd_doc.c Error reading Image from DOC device
3195 40 common/cmd_doc.c Image header has correct magic number
3196 41 common/cmd_ide.c before loading a Image from a IDE device
3197 -42 common/cmd_ide.c Bad usage of "ide" command
3198 42 common/cmd_ide.c correct usage of "ide" command
3199 -43 common/cmd_ide.c No boot device
3200 43 common/cmd_ide.c boot device found
3201 -44 common/cmd_ide.c Device not available
3202 44 common/cmd_ide.c Device available
3203 -45 common/cmd_ide.c wrong partition selected
3204 45 common/cmd_ide.c partition selected
3205 -46 common/cmd_ide.c Unknown partition table
3206 46 common/cmd_ide.c valid partition table found
3207 -47 common/cmd_ide.c Invalid partition type
3208 47 common/cmd_ide.c correct partition type
3209 -48 common/cmd_ide.c Error reading Image Header on boot device
3210 48 common/cmd_ide.c reading Image Header from IDE device OK
3211 -49 common/cmd_ide.c Image header has bad magic number
3212 49 common/cmd_ide.c Image header has correct magic number
3213 -50 common/cmd_ide.c Image header has bad checksum
3214 50 common/cmd_ide.c Image header has correct checksum
3215 -51 common/cmd_ide.c Error reading Image from IDE device
3216 51 common/cmd_ide.c reading Image from IDE device OK
3217 52 common/cmd_nand.c before loading a Image from a NAND device
3218 -53 common/cmd_nand.c Bad usage of "nand" command
3219 53 common/cmd_nand.c correct usage of "nand" command
3220 -54 common/cmd_nand.c No boot device
3221 54 common/cmd_nand.c boot device found
3222 -55 common/cmd_nand.c Unknown Chip ID on boot device
3223 55 common/cmd_nand.c correct chip ID found, device available
3224 -56 common/cmd_nand.c Error reading Image Header on boot device
3225 56 common/cmd_nand.c reading Image Header from NAND device OK
3226 -57 common/cmd_nand.c Image header has bad magic number
3227 57 common/cmd_nand.c Image header has correct magic number
3228 -58 common/cmd_nand.c Error reading Image from NAND device
3229 58 common/cmd_nand.c reading Image from NAND device OK
3231 -60 common/env_common.c Environment has a bad CRC, using default
3233 64 net/eth.c starting with Ethernet configuration.
3234 -64 net/eth.c no Ethernet found.
3235 65 net/eth.c Ethernet found.
3237 -80 common/cmd_net.c usage wrong
3238 80 common/cmd_net.c before calling NetLoop()
3239 -81 common/cmd_net.c some error in NetLoop() occurred
3240 81 common/cmd_net.c NetLoop() back without error
3241 -82 common/cmd_net.c size == 0 (File with size 0 loaded)
3242 82 common/cmd_net.c trying automatic boot
3243 83 common/cmd_net.c running "source" command
3244 -83 common/cmd_net.c some error in automatic boot or "source" command
3245 84 common/cmd_net.c end without errors
3250 100 common/cmd_bootm.c Kernel FIT Image has correct format
3251 -100 common/cmd_bootm.c Kernel FIT Image has incorrect format
3252 101 common/cmd_bootm.c No Kernel subimage unit name, using configuration
3253 -101 common/cmd_bootm.c Can't get configuration for kernel subimage
3254 102 common/cmd_bootm.c Kernel unit name specified
3255 -103 common/cmd_bootm.c Can't get kernel subimage node offset
3256 103 common/cmd_bootm.c Found configuration node
3257 104 common/cmd_bootm.c Got kernel subimage node offset
3258 -104 common/cmd_bootm.c Kernel subimage hash verification failed
3259 105 common/cmd_bootm.c Kernel subimage hash verification OK
3260 -105 common/cmd_bootm.c Kernel subimage is for unsupported architecture
3261 106 common/cmd_bootm.c Architecture check OK
3262 -106 common/cmd_bootm.c Kernel subimage has wrong type
3263 107 common/cmd_bootm.c Kernel subimage type OK
3264 -107 common/cmd_bootm.c Can't get kernel subimage data/size
3265 108 common/cmd_bootm.c Got kernel subimage data/size
3266 -108 common/cmd_bootm.c Wrong image type (not legacy, FIT)
3267 -109 common/cmd_bootm.c Can't get kernel subimage type
3268 -110 common/cmd_bootm.c Can't get kernel subimage comp
3269 -111 common/cmd_bootm.c Can't get kernel subimage os
3270 -112 common/cmd_bootm.c Can't get kernel subimage load address
3271 -113 common/cmd_bootm.c Image uncompress/copy overwrite error
3273 120 common/image.c Start initial ramdisk verification
3274 -120 common/image.c Ramdisk FIT image has incorrect format
3275 121 common/image.c Ramdisk FIT image has correct format
3276 122 common/image.c No ramdisk subimage unit name, using configuration
3277 -122 common/image.c Can't get configuration for ramdisk subimage
3278 123 common/image.c Ramdisk unit name specified
3279 -124 common/image.c Can't get ramdisk subimage node offset
3280 125 common/image.c Got ramdisk subimage node offset
3281 -125 common/image.c Ramdisk subimage hash verification failed
3282 126 common/image.c Ramdisk subimage hash verification OK
3283 -126 common/image.c Ramdisk subimage for unsupported architecture
3284 127 common/image.c Architecture check OK
3285 -127 common/image.c Can't get ramdisk subimage data/size
3286 128 common/image.c Got ramdisk subimage data/size
3287 129 common/image.c Can't get ramdisk load address
3288 -129 common/image.c Got ramdisk load address
3290 -130 common/cmd_doc.c Incorrect FIT image format
3291 131 common/cmd_doc.c FIT image format OK
3293 -140 common/cmd_ide.c Incorrect FIT image format
3294 141 common/cmd_ide.c FIT image format OK
3296 -150 common/cmd_nand.c Incorrect FIT image format
3297 151 common/cmd_nand.c FIT image format OK
3299 - legacy image format:
3300 CONFIG_IMAGE_FORMAT_LEGACY
3301 enables the legacy image format support in U-Boot.
3304 enabled if CONFIG_FIT_SIGNATURE is not defined.
3306 CONFIG_DISABLE_IMAGE_LEGACY
3307 disable the legacy image format
3309 This define is introduced, as the legacy image format is
3310 enabled per default for backward compatibility.
3312 - FIT image support:
3314 Enable support for the FIT uImage format.
3316 CONFIG_FIT_BEST_MATCH
3317 When no configuration is explicitly selected, default to the
3318 one whose fdt's compatibility field best matches that of
3319 U-Boot itself. A match is considered "best" if it matches the
3320 most specific compatibility entry of U-Boot's fdt's root node.
3321 The order of entries in the configuration's fdt is ignored.
3323 CONFIG_FIT_SIGNATURE
3324 This option enables signature verification of FIT uImages,
3325 using a hash signed and verified using RSA. See
3326 doc/uImage.FIT/signature.txt for more details.
3328 WARNING: When relying on signed FIT images with required
3329 signature check the legacy image format is default
3330 disabled. If a board need legacy image format support
3331 enable this through CONFIG_IMAGE_FORMAT_LEGACY
3333 CONFIG_FIT_DISABLE_SHA256
3334 Supporting SHA256 hashes has quite an impact on binary size.
3335 For constrained systems sha256 hash support can be disabled
3338 - Standalone program support:
3339 CONFIG_STANDALONE_LOAD_ADDR
3341 This option defines a board specific value for the
3342 address where standalone program gets loaded, thus
3343 overwriting the architecture dependent default
3346 - Frame Buffer Address:
3349 Define CONFIG_FB_ADDR if you want to use specific
3350 address for frame buffer. This is typically the case
3351 when using a graphics controller has separate video
3352 memory. U-Boot will then place the frame buffer at
3353 the given address instead of dynamically reserving it
3354 in system RAM by calling lcd_setmem(), which grabs
3355 the memory for the frame buffer depending on the
3356 configured panel size.
3358 Please see board_init_f function.
3360 - Automatic software updates via TFTP server
3362 CONFIG_UPDATE_TFTP_CNT_MAX
3363 CONFIG_UPDATE_TFTP_MSEC_MAX
3365 These options enable and control the auto-update feature;
3366 for a more detailed description refer to doc/README.update.
3368 - MTD Support (mtdparts command, UBI support)
3371 Adds the MTD device infrastructure from the Linux kernel.
3372 Needed for mtdparts command support.
3374 CONFIG_MTD_PARTITIONS
3376 Adds the MTD partitioning infrastructure from the Linux
3377 kernel. Needed for UBI support.
3379 CONFIG_MTD_NAND_VERIFY_WRITE
3380 verify if the written data is correct reread.
3385 Adds commands for interacting with MTD partitions formatted
3386 with the UBI flash translation layer
3388 Requires also defining CONFIG_RBTREE
3390 CONFIG_UBI_SILENCE_MSG
3392 Make the verbose messages from UBI stop printing. This leaves
3393 warnings and errors enabled.
3396 CONFIG_MTD_UBI_WL_THRESHOLD
3397 This parameter defines the maximum difference between the highest
3398 erase counter value and the lowest erase counter value of eraseblocks
3399 of UBI devices. When this threshold is exceeded, UBI starts performing
3400 wear leveling by means of moving data from eraseblock with low erase
3401 counter to eraseblocks with high erase counter.
3403 The default value should be OK for SLC NAND flashes, NOR flashes and
3404 other flashes which have eraseblock life-cycle 100000 or more.
3405 However, in case of MLC NAND flashes which typically have eraseblock
3406 life-cycle less than 10000, the threshold should be lessened (e.g.,
3407 to 128 or 256, although it does not have to be power of 2).
3411 CONFIG_MTD_UBI_BEB_LIMIT
3412 This option specifies the maximum bad physical eraseblocks UBI
3413 expects on the MTD device (per 1024 eraseblocks). If the
3414 underlying flash does not admit of bad eraseblocks (e.g. NOR
3415 flash), this value is ignored.
3417 NAND datasheets often specify the minimum and maximum NVM
3418 (Number of Valid Blocks) for the flashes' endurance lifetime.
3419 The maximum expected bad eraseblocks per 1024 eraseblocks
3420 then can be calculated as "1024 * (1 - MinNVB / MaxNVB)",
3421 which gives 20 for most NANDs (MaxNVB is basically the total
3422 count of eraseblocks on the chip).
3424 To put it differently, if this value is 20, UBI will try to
3425 reserve about 1.9% of physical eraseblocks for bad blocks
3426 handling. And that will be 1.9% of eraseblocks on the entire
3427 NAND chip, not just the MTD partition UBI attaches. This means
3428 that if you have, say, a NAND flash chip admits maximum 40 bad
3429 eraseblocks, and it is split on two MTD partitions of the same
3430 size, UBI will reserve 40 eraseblocks when attaching a
3435 CONFIG_MTD_UBI_FASTMAP
3436 Fastmap is a mechanism which allows attaching an UBI device
3437 in nearly constant time. Instead of scanning the whole MTD device it
3438 only has to locate a checkpoint (called fastmap) on the device.
3439 The on-flash fastmap contains all information needed to attach
3440 the device. Using fastmap makes only sense on large devices where
3441 attaching by scanning takes long. UBI will not automatically install
3442 a fastmap on old images, but you can set the UBI parameter
3443 CONFIG_MTD_UBI_FASTMAP_AUTOCONVERT to 1 if you want so. Please note
3444 that fastmap-enabled images are still usable with UBI implementations
3445 without fastmap support. On typical flash devices the whole fastmap
3446 fits into one PEB. UBI will reserve PEBs to hold two fastmaps.
3448 CONFIG_MTD_UBI_FASTMAP_AUTOCONVERT
3449 Set this parameter to enable fastmap automatically on images
3456 Adds commands for interacting with UBI volumes formatted as
3457 UBIFS. UBIFS is read-only in u-boot.
3459 Requires UBI support as well as CONFIG_LZO
3461 CONFIG_UBIFS_SILENCE_MSG
3463 Make the verbose messages from UBIFS stop printing. This leaves
3464 warnings and errors enabled.
3468 Enable building of SPL globally.
3471 LDSCRIPT for linking the SPL binary.
3473 CONFIG_SPL_MAX_FOOTPRINT
3474 Maximum size in memory allocated to the SPL, BSS included.
3475 When defined, the linker checks that the actual memory
3476 used by SPL from _start to __bss_end does not exceed it.
3477 CONFIG_SPL_MAX_FOOTPRINT and CONFIG_SPL_BSS_MAX_SIZE
3478 must not be both defined at the same time.
3481 Maximum size of the SPL image (text, data, rodata, and
3482 linker lists sections), BSS excluded.
3483 When defined, the linker checks that the actual size does
3486 CONFIG_SPL_TEXT_BASE
3487 TEXT_BASE for linking the SPL binary.
3489 CONFIG_SPL_RELOC_TEXT_BASE
3490 Address to relocate to. If unspecified, this is equal to
3491 CONFIG_SPL_TEXT_BASE (i.e. no relocation is done).
3493 CONFIG_SPL_BSS_START_ADDR
3494 Link address for the BSS within the SPL binary.
3496 CONFIG_SPL_BSS_MAX_SIZE
3497 Maximum size in memory allocated to the SPL BSS.
3498 When defined, the linker checks that the actual memory used
3499 by SPL from __bss_start to __bss_end does not exceed it.
3500 CONFIG_SPL_MAX_FOOTPRINT and CONFIG_SPL_BSS_MAX_SIZE
3501 must not be both defined at the same time.
3504 Adress of the start of the stack SPL will use
3506 CONFIG_SPL_RELOC_STACK
3507 Adress of the start of the stack SPL will use after
3508 relocation. If unspecified, this is equal to
3511 CONFIG_SYS_SPL_MALLOC_START
3512 Starting address of the malloc pool used in SPL.
3514 CONFIG_SYS_SPL_MALLOC_SIZE
3515 The size of the malloc pool used in SPL.
3517 CONFIG_SPL_FRAMEWORK
3518 Enable the SPL framework under common/. This framework
3519 supports MMC, NAND and YMODEM loading of U-Boot and NAND
3520 NAND loading of the Linux Kernel.
3523 Enable booting directly to an OS from SPL.
3524 See also: doc/README.falcon
3526 CONFIG_SPL_DISPLAY_PRINT
3527 For ARM, enable an optional function to print more information
3528 about the running system.
3530 CONFIG_SPL_INIT_MINIMAL
3531 Arch init code should be built for a very small image
3533 CONFIG_SPL_LIBCOMMON_SUPPORT
3534 Support for common/libcommon.o in SPL binary
3536 CONFIG_SPL_LIBDISK_SUPPORT
3537 Support for disk/libdisk.o in SPL binary
3539 CONFIG_SPL_I2C_SUPPORT
3540 Support for drivers/i2c/libi2c.o in SPL binary
3542 CONFIG_SPL_GPIO_SUPPORT
3543 Support for drivers/gpio/libgpio.o in SPL binary
3545 CONFIG_SPL_MMC_SUPPORT
3546 Support for drivers/mmc/libmmc.o in SPL binary
3548 CONFIG_SYS_MMCSD_RAW_MODE_U_BOOT_SECTOR,
3549 CONFIG_SYS_U_BOOT_MAX_SIZE_SECTORS,
3550 CONFIG_SYS_MMC_SD_FS_BOOT_PARTITION
3551 Address, size and partition on the MMC to load U-Boot from
3552 when the MMC is being used in raw mode.
3554 CONFIG_SYS_MMCSD_RAW_MODE_KERNEL_SECTOR
3555 Sector to load kernel uImage from when MMC is being
3556 used in raw mode (for Falcon mode)
3558 CONFIG_SYS_MMCSD_RAW_MODE_ARGS_SECTOR,
3559 CONFIG_SYS_MMCSD_RAW_MODE_ARGS_SECTORS
3560 Sector and number of sectors to load kernel argument
3561 parameters from when MMC is being used in raw mode
3564 CONFIG_SPL_FAT_SUPPORT
3565 Support for fs/fat/libfat.o in SPL binary
3567 CONFIG_SPL_EXT_SUPPORT
3568 Support for EXT filesystem in SPL binary
3570 CONFIG_SPL_FS_LOAD_PAYLOAD_NAME
3571 Filename to read to load U-Boot when reading from filesystem
3573 CONFIG_SPL_FS_LOAD_KERNEL_NAME
3574 Filename to read to load kernel uImage when reading
3575 from filesystem (for Falcon mode)
3577 CONFIG_SPL_FS_LOAD_ARGS_NAME
3578 Filename to read to load kernel argument parameters
3579 when reading from filesystem (for Falcon mode)
3581 CONFIG_SPL_MPC83XX_WAIT_FOR_NAND
3582 Set this for NAND SPL on PPC mpc83xx targets, so that
3583 start.S waits for the rest of the SPL to load before
3584 continuing (the hardware starts execution after just
3585 loading the first page rather than the full 4K).
3587 CONFIG_SPL_SKIP_RELOCATE
3588 Avoid SPL relocation
3590 CONFIG_SPL_NAND_BASE
3591 Include nand_base.c in the SPL. Requires
3592 CONFIG_SPL_NAND_DRIVERS.
3594 CONFIG_SPL_NAND_DRIVERS
3595 SPL uses normal NAND drivers, not minimal drivers.
3598 Include standard software ECC in the SPL
3600 CONFIG_SPL_NAND_SIMPLE
3601 Support for NAND boot using simple NAND drivers that
3602 expose the cmd_ctrl() interface.
3604 CONFIG_SPL_MTD_SUPPORT
3605 Support for the MTD subsystem within SPL. Useful for
3606 environment on NAND support within SPL.
3608 CONFIG_SPL_NAND_RAW_ONLY
3609 Support to boot only raw u-boot.bin images. Use this only
3610 if you need to save space.
3612 CONFIG_SPL_MPC8XXX_INIT_DDR_SUPPORT
3613 Set for the SPL on PPC mpc8xxx targets, support for
3614 drivers/ddr/fsl/libddr.o in SPL binary.
3616 CONFIG_SPL_COMMON_INIT_DDR
3617 Set for common ddr init with serial presence detect in
3620 CONFIG_SYS_NAND_5_ADDR_CYCLE, CONFIG_SYS_NAND_PAGE_COUNT,
3621 CONFIG_SYS_NAND_PAGE_SIZE, CONFIG_SYS_NAND_OOBSIZE,
3622 CONFIG_SYS_NAND_BLOCK_SIZE, CONFIG_SYS_NAND_BAD_BLOCK_POS,
3623 CONFIG_SYS_NAND_ECCPOS, CONFIG_SYS_NAND_ECCSIZE,
3624 CONFIG_SYS_NAND_ECCBYTES
3625 Defines the size and behavior of the NAND that SPL uses
3628 CONFIG_SPL_NAND_BOOT
3629 Add support NAND boot
3631 CONFIG_SYS_NAND_U_BOOT_OFFS
3632 Location in NAND to read U-Boot from
3634 CONFIG_SYS_NAND_U_BOOT_DST
3635 Location in memory to load U-Boot to
3637 CONFIG_SYS_NAND_U_BOOT_SIZE
3638 Size of image to load
3640 CONFIG_SYS_NAND_U_BOOT_START
3641 Entry point in loaded image to jump to
3643 CONFIG_SYS_NAND_HW_ECC_OOBFIRST
3644 Define this if you need to first read the OOB and then the
3645 data. This is used for example on davinci plattforms.
3647 CONFIG_SPL_OMAP3_ID_NAND
3648 Support for an OMAP3-specific set of functions to return the
3649 ID and MFR of the first attached NAND chip, if present.
3651 CONFIG_SPL_SERIAL_SUPPORT
3652 Support for drivers/serial/libserial.o in SPL binary
3654 CONFIG_SPL_SPI_FLASH_SUPPORT
3655 Support for drivers/mtd/spi/libspi_flash.o in SPL binary
3657 CONFIG_SPL_SPI_SUPPORT
3658 Support for drivers/spi/libspi.o in SPL binary
3660 CONFIG_SPL_RAM_DEVICE
3661 Support for running image already present in ram, in SPL binary
3663 CONFIG_SPL_LIBGENERIC_SUPPORT
3664 Support for lib/libgeneric.o in SPL binary
3666 CONFIG_SPL_ENV_SUPPORT
3667 Support for the environment operating in SPL binary
3669 CONFIG_SPL_NET_SUPPORT
3670 Support for the net/libnet.o in SPL binary.
3671 It conflicts with SPL env from storage medium specified by
3672 CONFIG_ENV_IS_xxx but CONFIG_ENV_IS_NOWHERE
3675 Image offset to which the SPL should be padded before appending
3676 the SPL payload. By default, this is defined as
3677 CONFIG_SPL_MAX_SIZE, or 0 if CONFIG_SPL_MAX_SIZE is undefined.
3678 CONFIG_SPL_PAD_TO must be either 0, meaning to append the SPL
3679 payload without any padding, or >= CONFIG_SPL_MAX_SIZE.
3682 Final target image containing SPL and payload. Some SPLs
3683 use an arch-specific makefile fragment instead, for
3684 example if more than one image needs to be produced.
3686 CONFIG_FIT_SPL_PRINT
3687 Printing information about a FIT image adds quite a bit of
3688 code to SPL. So this is normally disabled in SPL. Use this
3689 option to re-enable it. This will affect the output of the
3690 bootm command when booting a FIT image.
3694 Enable building of TPL globally.
3697 Image offset to which the TPL should be padded before appending
3698 the TPL payload. By default, this is defined as
3699 CONFIG_SPL_MAX_SIZE, or 0 if CONFIG_SPL_MAX_SIZE is undefined.
3700 CONFIG_SPL_PAD_TO must be either 0, meaning to append the SPL
3701 payload without any padding, or >= CONFIG_SPL_MAX_SIZE.
3706 [so far only for SMDK2400 boards]
3708 - Modem support enable:
3709 CONFIG_MODEM_SUPPORT
3711 - RTS/CTS Flow control enable:
3714 - Modem debug support:
3715 CONFIG_MODEM_SUPPORT_DEBUG
3717 Enables debugging stuff (char screen[1024], dbg())
3718 for modem support. Useful only with BDI2000.
3720 - Interrupt support (PPC):
3722 There are common interrupt_init() and timer_interrupt()
3723 for all PPC archs. interrupt_init() calls interrupt_init_cpu()
3724 for CPU specific initialization. interrupt_init_cpu()
3725 should set decrementer_count to appropriate value. If
3726 CPU resets decrementer automatically after interrupt
3727 (ppc4xx) it should set decrementer_count to zero.
3728 timer_interrupt() calls timer_interrupt_cpu() for CPU
3729 specific handling. If board has watchdog / status_led
3730 / other_activity_monitor it works automatically from
3731 general timer_interrupt().
3735 In the target system modem support is enabled when a
3736 specific key (key combination) is pressed during
3737 power-on. Otherwise U-Boot will boot normally
3738 (autoboot). The key_pressed() function is called from
3739 board_init(). Currently key_pressed() is a dummy
3740 function, returning 1 and thus enabling modem
3743 If there are no modem init strings in the
3744 environment, U-Boot proceed to autoboot; the
3745 previous output (banner, info printfs) will be
3748 See also: doc/README.Modem
3750 Board initialization settings:
3751 ------------------------------
3753 During Initialization u-boot calls a number of board specific functions
3754 to allow the preparation of board specific prerequisites, e.g. pin setup
3755 before drivers are initialized. To enable these callbacks the
3756 following configuration macros have to be defined. Currently this is
3757 architecture specific, so please check arch/your_architecture/lib/board.c
3758 typically in board_init_f() and board_init_r().
3760 - CONFIG_BOARD_EARLY_INIT_F: Call board_early_init_f()
3761 - CONFIG_BOARD_EARLY_INIT_R: Call board_early_init_r()
3762 - CONFIG_BOARD_LATE_INIT: Call board_late_init()
3763 - CONFIG_BOARD_POSTCLK_INIT: Call board_postclk_init()
3765 Configuration Settings:
3766 -----------------------
3768 - CONFIG_SYS_SUPPORT_64BIT_DATA: Defined automatically if compiled as 64-bit.
3769 Optionally it can be defined to support 64-bit memory commands.
3771 - CONFIG_SYS_LONGHELP: Defined when you want long help messages included;
3772 undefine this when you're short of memory.
3774 - CONFIG_SYS_HELP_CMD_WIDTH: Defined when you want to override the default
3775 width of the commands listed in the 'help' command output.
3777 - CONFIG_SYS_PROMPT: This is what U-Boot prints on the console to
3778 prompt for user input.
3780 - CONFIG_SYS_CBSIZE: Buffer size for input from the Console
3782 - CONFIG_SYS_PBSIZE: Buffer size for Console output
3784 - CONFIG_SYS_MAXARGS: max. Number of arguments accepted for monitor commands
3786 - CONFIG_SYS_BARGSIZE: Buffer size for Boot Arguments which are passed to
3787 the application (usually a Linux kernel) when it is
3790 - CONFIG_SYS_BAUDRATE_TABLE:
3791 List of legal baudrate settings for this board.
3793 - CONFIG_SYS_CONSOLE_INFO_QUIET
3794 Suppress display of console information at boot.
3796 - CONFIG_SYS_CONSOLE_IS_IN_ENV
3797 If the board specific function
3798 extern int overwrite_console (void);
3799 returns 1, the stdin, stderr and stdout are switched to the
3800 serial port, else the settings in the environment are used.
3802 - CONFIG_SYS_CONSOLE_OVERWRITE_ROUTINE
3803 Enable the call to overwrite_console().
3805 - CONFIG_SYS_CONSOLE_ENV_OVERWRITE
3806 Enable overwrite of previous console environment settings.
3808 - CONFIG_SYS_MEMTEST_START, CONFIG_SYS_MEMTEST_END:
3809 Begin and End addresses of the area used by the
3812 - CONFIG_SYS_ALT_MEMTEST:
3813 Enable an alternate, more extensive memory test.
3815 - CONFIG_SYS_MEMTEST_SCRATCH:
3816 Scratch address used by the alternate memory test
3817 You only need to set this if address zero isn't writeable
3819 - CONFIG_SYS_MEM_TOP_HIDE (PPC only):
3820 If CONFIG_SYS_MEM_TOP_HIDE is defined in the board config header,
3821 this specified memory area will get subtracted from the top
3822 (end) of RAM and won't get "touched" at all by U-Boot. By
3823 fixing up gd->ram_size the Linux kernel should gets passed
3824 the now "corrected" memory size and won't touch it either.
3825 This should work for arch/ppc and arch/powerpc. Only Linux
3826 board ports in arch/powerpc with bootwrapper support that
3827 recalculate the memory size from the SDRAM controller setup
3828 will have to get fixed in Linux additionally.
3830 This option can be used as a workaround for the 440EPx/GRx
3831 CHIP 11 errata where the last 256 bytes in SDRAM shouldn't
3834 WARNING: Please make sure that this value is a multiple of
3835 the Linux page size (normally 4k). If this is not the case,
3836 then the end address of the Linux memory will be located at a
3837 non page size aligned address and this could cause major
3840 - CONFIG_SYS_LOADS_BAUD_CHANGE:
3841 Enable temporary baudrate change while serial download
3843 - CONFIG_SYS_SDRAM_BASE:
3844 Physical start address of SDRAM. _Must_ be 0 here.
3846 - CONFIG_SYS_MBIO_BASE:
3847 Physical start address of Motherboard I/O (if using a
3850 - CONFIG_SYS_FLASH_BASE:
3851 Physical start address of Flash memory.
3853 - CONFIG_SYS_MONITOR_BASE:
3854 Physical start address of boot monitor code (set by
3855 make config files to be same as the text base address
3856 (CONFIG_SYS_TEXT_BASE) used when linking) - same as
3857 CONFIG_SYS_FLASH_BASE when booting from flash.
3859 - CONFIG_SYS_MONITOR_LEN:
3860 Size of memory reserved for monitor code, used to
3861 determine _at_compile_time_ (!) if the environment is
3862 embedded within the U-Boot image, or in a separate
3865 - CONFIG_SYS_MALLOC_LEN:
3866 Size of DRAM reserved for malloc() use.
3868 - CONFIG_SYS_MALLOC_F_LEN
3869 Size of the malloc() pool for use before relocation. If
3870 this is defined, then a very simple malloc() implementation
3871 will become available before relocation. The address is just
3872 below the global data, and the stack is moved down to make
3875 This feature allocates regions with increasing addresses
3876 within the region. calloc() is supported, but realloc()
3877 is not available. free() is supported but does nothing.
3878 The memory will be freed (or in fact just forgotton) when
3879 U-Boot relocates itself.
3881 Pre-relocation malloc() is only supported on ARM and sandbox
3882 at present but is fairly easy to enable for other archs.
3884 - CONFIG_SYS_BOOTM_LEN:
3885 Normally compressed uImages are limited to an
3886 uncompressed size of 8 MBytes. If this is not enough,
3887 you can define CONFIG_SYS_BOOTM_LEN in your board config file
3888 to adjust this setting to your needs.
3890 - CONFIG_SYS_BOOTMAPSZ:
3891 Maximum size of memory mapped by the startup code of
3892 the Linux kernel; all data that must be processed by
3893 the Linux kernel (bd_info, boot arguments, FDT blob if
3894 used) must be put below this limit, unless "bootm_low"
3895 environment variable is defined and non-zero. In such case
3896 all data for the Linux kernel must be between "bootm_low"
3897 and "bootm_low" + CONFIG_SYS_BOOTMAPSZ. The environment
3898 variable "bootm_mapsize" will override the value of
3899 CONFIG_SYS_BOOTMAPSZ. If CONFIG_SYS_BOOTMAPSZ is undefined,
3900 then the value in "bootm_size" will be used instead.
3902 - CONFIG_SYS_BOOT_RAMDISK_HIGH:
3903 Enable initrd_high functionality. If defined then the
3904 initrd_high feature is enabled and the bootm ramdisk subcommand
3907 - CONFIG_SYS_BOOT_GET_CMDLINE:
3908 Enables allocating and saving kernel cmdline in space between
3909 "bootm_low" and "bootm_low" + BOOTMAPSZ.
3911 - CONFIG_SYS_BOOT_GET_KBD:
3912 Enables allocating and saving a kernel copy of the bd_info in
3913 space between "bootm_low" and "bootm_low" + BOOTMAPSZ.
3915 - CONFIG_SYS_MAX_FLASH_BANKS:
3916 Max number of Flash memory banks
3918 - CONFIG_SYS_MAX_FLASH_SECT:
3919 Max number of sectors on a Flash chip
3921 - CONFIG_SYS_FLASH_ERASE_TOUT:
3922 Timeout for Flash erase operations (in ms)
3924 - CONFIG_SYS_FLASH_WRITE_TOUT:
3925 Timeout for Flash write operations (in ms)
3927 - CONFIG_SYS_FLASH_LOCK_TOUT
3928 Timeout for Flash set sector lock bit operation (in ms)
3930 - CONFIG_SYS_FLASH_UNLOCK_TOUT
3931 Timeout for Flash clear lock bits operation (in ms)
3933 - CONFIG_SYS_FLASH_PROTECTION
3934 If defined, hardware flash sectors protection is used
3935 instead of U-Boot software protection.
3937 - CONFIG_SYS_DIRECT_FLASH_TFTP:
3939 Enable TFTP transfers directly to flash memory;
3940 without this option such a download has to be
3941 performed in two steps: (1) download to RAM, and (2)
3942 copy from RAM to flash.
3944 The two-step approach is usually more reliable, since
3945 you can check if the download worked before you erase
3946 the flash, but in some situations (when system RAM is
3947 too limited to allow for a temporary copy of the
3948 downloaded image) this option may be very useful.
3950 - CONFIG_SYS_FLASH_CFI:
3951 Define if the flash driver uses extra elements in the
3952 common flash structure for storing flash geometry.
3954 - CONFIG_FLASH_CFI_DRIVER
3955 This option also enables the building of the cfi_flash driver
3956 in the drivers directory
3958 - CONFIG_FLASH_CFI_MTD
3959 This option enables the building of the cfi_mtd driver
3960 in the drivers directory. The driver exports CFI flash
3963 - CONFIG_SYS_FLASH_USE_BUFFER_WRITE
3964 Use buffered writes to flash.
3966 - CONFIG_FLASH_SPANSION_S29WS_N
3967 s29ws-n MirrorBit flash has non-standard addresses for buffered
3970 - CONFIG_SYS_FLASH_QUIET_TEST
3971 If this option is defined, the common CFI flash doesn't
3972 print it's warning upon not recognized FLASH banks. This
3973 is useful, if some of the configured banks are only
3974 optionally available.
3976 - CONFIG_FLASH_SHOW_PROGRESS
3977 If defined (must be an integer), print out countdown
3978 digits and dots. Recommended value: 45 (9..1) for 80
3979 column displays, 15 (3..1) for 40 column displays.
3981 - CONFIG_FLASH_VERIFY
3982 If defined, the content of the flash (destination) is compared
3983 against the source after the write operation. An error message
3984 will be printed when the contents are not identical.
3985 Please note that this option is useless in nearly all cases,
3986 since such flash programming errors usually are detected earlier
3987 while unprotecting/erasing/programming. Please only enable
3988 this option if you really know what you are doing.
3990 - CONFIG_SYS_RX_ETH_BUFFER:
3991 Defines the number of Ethernet receive buffers. On some
3992 Ethernet controllers it is recommended to set this value
3993 to 8 or even higher (EEPRO100 or 405 EMAC), since all
3994 buffers can be full shortly after enabling the interface
3995 on high Ethernet traffic.
3996 Defaults to 4 if not defined.
3998 - CONFIG_ENV_MAX_ENTRIES
4000 Maximum number of entries in the hash table that is used
4001 internally to store the environment settings. The default
4002 setting is supposed to be generous and should work in most
4003 cases. This setting can be used to tune behaviour; see
4004 lib/hashtable.c for details.
4006 - CONFIG_ENV_FLAGS_LIST_DEFAULT
4007 - CONFIG_ENV_FLAGS_LIST_STATIC
4008 Enable validation of the values given to environment variables when
4009 calling env set. Variables can be restricted to only decimal,
4010 hexadecimal, or boolean. If CONFIG_CMD_NET is also defined,
4011 the variables can also be restricted to IP address or MAC address.
4013 The format of the list is:
4014 type_attribute = [s|d|x|b|i|m]
4015 access_atribute = [a|r|o|c]
4016 attributes = type_attribute[access_atribute]
4017 entry = variable_name[:attributes]
4020 The type attributes are:
4021 s - String (default)
4024 b - Boolean ([1yYtT|0nNfF])
4028 The access attributes are:
4034 - CONFIG_ENV_FLAGS_LIST_DEFAULT
4035 Define this to a list (string) to define the ".flags"
4036 envirnoment variable in the default or embedded environment.
4038 - CONFIG_ENV_FLAGS_LIST_STATIC
4039 Define this to a list (string) to define validation that
4040 should be done if an entry is not found in the ".flags"
4041 environment variable. To override a setting in the static
4042 list, simply add an entry for the same variable name to the
4045 - CONFIG_ENV_ACCESS_IGNORE_FORCE
4046 If defined, don't allow the -f switch to env set override variable
4049 - CONFIG_SYS_GENERIC_BOARD
4050 This selects the architecture-generic board system instead of the
4051 architecture-specific board files. It is intended to move boards
4052 to this new framework over time. Defining this will disable the
4053 arch/foo/lib/board.c file and use common/board_f.c and
4054 common/board_r.c instead. To use this option your architecture
4055 must support it (i.e. must define __HAVE_ARCH_GENERIC_BOARD in
4056 its config.mk file). If you find problems enabling this option on
4057 your board please report the problem and send patches!
4059 - CONFIG_OMAP_PLATFORM_RESET_TIME_MAX_USEC (OMAP only)
4060 This is set by OMAP boards for the max time that reset should
4061 be asserted. See doc/README.omap-reset-time for details on how
4062 the value can be calulated on a given board.
4065 If stdint.h is available with your toolchain you can define this
4066 option to enable it. You can provide option 'USE_STDINT=1' when
4067 building U-Boot to enable this.
4069 The following definitions that deal with the placement and management
4070 of environment data (variable area); in general, we support the
4071 following configurations:
4073 - CONFIG_BUILD_ENVCRC:
4075 Builds up envcrc with the target environment so that external utils
4076 may easily extract it and embed it in final U-Boot images.
4078 - CONFIG_ENV_IS_IN_FLASH:
4080 Define this if the environment is in flash memory.
4082 a) The environment occupies one whole flash sector, which is
4083 "embedded" in the text segment with the U-Boot code. This
4084 happens usually with "bottom boot sector" or "top boot
4085 sector" type flash chips, which have several smaller
4086 sectors at the start or the end. For instance, such a
4087 layout can have sector sizes of 8, 2x4, 16, Nx32 kB. In
4088 such a case you would place the environment in one of the
4089 4 kB sectors - with U-Boot code before and after it. With
4090 "top boot sector" type flash chips, you would put the
4091 environment in one of the last sectors, leaving a gap
4092 between U-Boot and the environment.
4094 - CONFIG_ENV_OFFSET:
4096 Offset of environment data (variable area) to the
4097 beginning of flash memory; for instance, with bottom boot
4098 type flash chips the second sector can be used: the offset
4099 for this sector is given here.
4101 CONFIG_ENV_OFFSET is used relative to CONFIG_SYS_FLASH_BASE.
4105 This is just another way to specify the start address of
4106 the flash sector containing the environment (instead of
4109 - CONFIG_ENV_SECT_SIZE:
4111 Size of the sector containing the environment.
4114 b) Sometimes flash chips have few, equal sized, BIG sectors.
4115 In such a case you don't want to spend a whole sector for
4120 If you use this in combination with CONFIG_ENV_IS_IN_FLASH
4121 and CONFIG_ENV_SECT_SIZE, you can specify to use only a part
4122 of this flash sector for the environment. This saves
4123 memory for the RAM copy of the environment.
4125 It may also save flash memory if you decide to use this
4126 when your environment is "embedded" within U-Boot code,
4127 since then the remainder of the flash sector could be used
4128 for U-Boot code. It should be pointed out that this is
4129 STRONGLY DISCOURAGED from a robustness point of view:
4130 updating the environment in flash makes it always
4131 necessary to erase the WHOLE sector. If something goes
4132 wrong before the contents has been restored from a copy in
4133 RAM, your target system will be dead.
4135 - CONFIG_ENV_ADDR_REDUND
4136 CONFIG_ENV_SIZE_REDUND
4138 These settings describe a second storage area used to hold
4139 a redundant copy of the environment data, so that there is
4140 a valid backup copy in case there is a power failure during
4141 a "saveenv" operation.
4143 BE CAREFUL! Any changes to the flash layout, and some changes to the
4144 source code will make it necessary to adapt <board>/u-boot.lds*
4148 - CONFIG_ENV_IS_IN_NVRAM:
4150 Define this if you have some non-volatile memory device
4151 (NVRAM, battery buffered SRAM) which you want to use for the
4157 These two #defines are used to determine the memory area you
4158 want to use for environment. It is assumed that this memory
4159 can just be read and written to, without any special
4162 BE CAREFUL! The first access to the environment happens quite early
4163 in U-Boot initalization (when we try to get the setting of for the
4164 console baudrate). You *MUST* have mapped your NVRAM area then, or
4167 Please note that even with NVRAM we still use a copy of the
4168 environment in RAM: we could work on NVRAM directly, but we want to
4169 keep settings there always unmodified except somebody uses "saveenv"
4170 to save the current settings.
4173 - CONFIG_ENV_IS_IN_EEPROM:
4175 Use this if you have an EEPROM or similar serial access
4176 device and a driver for it.
4178 - CONFIG_ENV_OFFSET:
4181 These two #defines specify the offset and size of the
4182 environment area within the total memory of your EEPROM.
4184 - CONFIG_SYS_I2C_EEPROM_ADDR:
4185 If defined, specified the chip address of the EEPROM device.
4186 The default address is zero.
4188 - CONFIG_SYS_EEPROM_PAGE_WRITE_BITS:
4189 If defined, the number of bits used to address bytes in a
4190 single page in the EEPROM device. A 64 byte page, for example
4191 would require six bits.
4193 - CONFIG_SYS_EEPROM_PAGE_WRITE_DELAY_MS:
4194 If defined, the number of milliseconds to delay between
4195 page writes. The default is zero milliseconds.
4197 - CONFIG_SYS_I2C_EEPROM_ADDR_LEN:
4198 The length in bytes of the EEPROM memory array address. Note
4199 that this is NOT the chip address length!
4201 - CONFIG_SYS_I2C_EEPROM_ADDR_OVERFLOW:
4202 EEPROM chips that implement "address overflow" are ones
4203 like Catalyst 24WC04/08/16 which has 9/10/11 bits of
4204 address and the extra bits end up in the "chip address" bit
4205 slots. This makes a 24WC08 (1Kbyte) chip look like four 256
4208 Note that we consider the length of the address field to
4209 still be one byte because the extra address bits are hidden
4210 in the chip address.
4212 - CONFIG_SYS_EEPROM_SIZE:
4213 The size in bytes of the EEPROM device.
4215 - CONFIG_ENV_EEPROM_IS_ON_I2C
4216 define this, if you have I2C and SPI activated, and your
4217 EEPROM, which holds the environment, is on the I2C bus.
4219 - CONFIG_I2C_ENV_EEPROM_BUS
4220 if you have an Environment on an EEPROM reached over
4221 I2C muxes, you can define here, how to reach this
4222 EEPROM. For example:
4224 #define CONFIG_I2C_ENV_EEPROM_BUS 1
4226 EEPROM which holds the environment, is reached over
4227 a pca9547 i2c mux with address 0x70, channel 3.
4229 - CONFIG_ENV_IS_IN_DATAFLASH:
4231 Define this if you have a DataFlash memory device which you
4232 want to use for the environment.
4234 - CONFIG_ENV_OFFSET:
4238 These three #defines specify the offset and size of the
4239 environment area within the total memory of your DataFlash placed
4240 at the specified address.
4242 - CONFIG_ENV_IS_IN_SPI_FLASH:
4244 Define this if you have a SPI Flash memory device which you
4245 want to use for the environment.
4247 - CONFIG_ENV_OFFSET:
4250 These two #defines specify the offset and size of the
4251 environment area within the SPI Flash. CONFIG_ENV_OFFSET must be
4252 aligned to an erase sector boundary.
4254 - CONFIG_ENV_SECT_SIZE:
4256 Define the SPI flash's sector size.
4258 - CONFIG_ENV_OFFSET_REDUND (optional):
4260 This setting describes a second storage area of CONFIG_ENV_SIZE
4261 size used to hold a redundant copy of the environment data, so
4262 that there is a valid backup copy in case there is a power failure
4263 during a "saveenv" operation. CONFIG_ENV_OFFSET_RENDUND must be
4264 aligned to an erase sector boundary.
4266 - CONFIG_ENV_SPI_BUS (optional):
4267 - CONFIG_ENV_SPI_CS (optional):
4269 Define the SPI bus and chip select. If not defined they will be 0.
4271 - CONFIG_ENV_SPI_MAX_HZ (optional):
4273 Define the SPI max work clock. If not defined then use 1MHz.
4275 - CONFIG_ENV_SPI_MODE (optional):
4277 Define the SPI work mode. If not defined then use SPI_MODE_3.
4279 - CONFIG_ENV_IS_IN_REMOTE:
4281 Define this if you have a remote memory space which you
4282 want to use for the local device's environment.
4287 These two #defines specify the address and size of the
4288 environment area within the remote memory space. The
4289 local device can get the environment from remote memory
4290 space by SRIO or PCIE links.
4292 BE CAREFUL! For some special cases, the local device can not use
4293 "saveenv" command. For example, the local device will get the
4294 environment stored in a remote NOR flash by SRIO or PCIE link,
4295 but it can not erase, write this NOR flash by SRIO or PCIE interface.
4297 - CONFIG_ENV_IS_IN_NAND:
4299 Define this if you have a NAND device which you want to use
4300 for the environment.
4302 - CONFIG_ENV_OFFSET:
4305 These two #defines specify the offset and size of the environment
4306 area within the first NAND device. CONFIG_ENV_OFFSET must be
4307 aligned to an erase block boundary.
4309 - CONFIG_ENV_OFFSET_REDUND (optional):
4311 This setting describes a second storage area of CONFIG_ENV_SIZE
4312 size used to hold a redundant copy of the environment data, so
4313 that there is a valid backup copy in case there is a power failure
4314 during a "saveenv" operation. CONFIG_ENV_OFFSET_RENDUND must be
4315 aligned to an erase block boundary.
4317 - CONFIG_ENV_RANGE (optional):
4319 Specifies the length of the region in which the environment
4320 can be written. This should be a multiple of the NAND device's
4321 block size. Specifying a range with more erase blocks than
4322 are needed to hold CONFIG_ENV_SIZE allows bad blocks within
4323 the range to be avoided.
4325 - CONFIG_ENV_OFFSET_OOB (optional):
4327 Enables support for dynamically retrieving the offset of the
4328 environment from block zero's out-of-band data. The
4329 "nand env.oob" command can be used to record this offset.
4330 Currently, CONFIG_ENV_OFFSET_REDUND is not supported when
4331 using CONFIG_ENV_OFFSET_OOB.
4333 - CONFIG_NAND_ENV_DST
4335 Defines address in RAM to which the nand_spl code should copy the
4336 environment. If redundant environment is used, it will be copied to
4337 CONFIG_NAND_ENV_DST + CONFIG_ENV_SIZE.
4339 - CONFIG_ENV_IS_IN_UBI:
4341 Define this if you have an UBI volume that you want to use for the
4342 environment. This has the benefit of wear-leveling the environment
4343 accesses, which is important on NAND.
4345 - CONFIG_ENV_UBI_PART:
4347 Define this to a string that is the mtd partition containing the UBI.
4349 - CONFIG_ENV_UBI_VOLUME:
4351 Define this to the name of the volume that you want to store the
4354 - CONFIG_ENV_UBI_VOLUME_REDUND:
4356 Define this to the name of another volume to store a second copy of
4357 the environment in. This will enable redundant environments in UBI.
4358 It is assumed that both volumes are in the same MTD partition.
4360 - CONFIG_UBI_SILENCE_MSG
4361 - CONFIG_UBIFS_SILENCE_MSG
4363 You will probably want to define these to avoid a really noisy system
4364 when storing the env in UBI.
4366 - CONFIG_ENV_IS_IN_FAT:
4367 Define this if you want to use the FAT file system for the environment.
4369 - FAT_ENV_INTERFACE:
4371 Define this to a string that is the name of the block device.
4373 - FAT_ENV_DEV_AND_PART:
4375 Define this to a string to specify the partition of the device. It can
4378 "D:P", "D:0", "D", "D:" or "D:auto" (D, P are integers. And P >= 1)
4379 - "D:P": device D partition P. Error occurs if device D has no
4382 - "D" or "D:": device D partition 1 if device D has partition
4383 table, or the whole device D if has no partition
4385 - "D:auto": first partition in device D with bootable flag set.
4386 If none, first valid paratition in device D. If no
4387 partition table then means device D.
4391 It's a string of the FAT file name. This file use to store the
4395 This should be defined. Otherwise it cannot save the envrionment file.
4397 - CONFIG_ENV_IS_IN_MMC:
4399 Define this if you have an MMC device which you want to use for the
4402 - CONFIG_SYS_MMC_ENV_DEV:
4404 Specifies which MMC device the environment is stored in.
4406 - CONFIG_SYS_MMC_ENV_PART (optional):
4408 Specifies which MMC partition the environment is stored in. If not
4409 set, defaults to partition 0, the user area. Common values might be
4410 1 (first MMC boot partition), 2 (second MMC boot partition).
4412 - CONFIG_ENV_OFFSET:
4415 These two #defines specify the offset and size of the environment
4416 area within the specified MMC device.
4418 If offset is positive (the usual case), it is treated as relative to
4419 the start of the MMC partition. If offset is negative, it is treated
4420 as relative to the end of the MMC partition. This can be useful if
4421 your board may be fitted with different MMC devices, which have
4422 different sizes for the MMC partitions, and you always want the
4423 environment placed at the very end of the partition, to leave the
4424 maximum possible space before it, to store other data.
4426 These two values are in units of bytes, but must be aligned to an
4427 MMC sector boundary.
4429 - CONFIG_ENV_OFFSET_REDUND (optional):
4431 Specifies a second storage area, of CONFIG_ENV_SIZE size, used to
4432 hold a redundant copy of the environment data. This provides a
4433 valid backup copy in case the other copy is corrupted, e.g. due
4434 to a power failure during a "saveenv" operation.
4436 This value may also be positive or negative; this is handled in the
4437 same way as CONFIG_ENV_OFFSET.
4439 This value is also in units of bytes, but must also be aligned to
4440 an MMC sector boundary.
4442 - CONFIG_ENV_SIZE_REDUND (optional):
4444 This value need not be set, even when CONFIG_ENV_OFFSET_REDUND is
4445 set. If this value is set, it must be set to the same value as
4448 - CONFIG_SYS_SPI_INIT_OFFSET
4450 Defines offset to the initial SPI buffer area in DPRAM. The
4451 area is used at an early stage (ROM part) if the environment
4452 is configured to reside in the SPI EEPROM: We need a 520 byte
4453 scratch DPRAM area. It is used between the two initialization
4454 calls (spi_init_f() and spi_init_r()). A value of 0xB00 seems
4455 to be a good choice since it makes it far enough from the
4456 start of the data area as well as from the stack pointer.
4458 Please note that the environment is read-only until the monitor
4459 has been relocated to RAM and a RAM copy of the environment has been
4460 created; also, when using EEPROM you will have to use getenv_f()
4461 until then to read environment variables.
4463 The environment is protected by a CRC32 checksum. Before the monitor
4464 is relocated into RAM, as a result of a bad CRC you will be working
4465 with the compiled-in default environment - *silently*!!! [This is
4466 necessary, because the first environment variable we need is the
4467 "baudrate" setting for the console - if we have a bad CRC, we don't
4468 have any device yet where we could complain.]
4470 Note: once the monitor has been relocated, then it will complain if
4471 the default environment is used; a new CRC is computed as soon as you
4472 use the "saveenv" command to store a valid environment.
4474 - CONFIG_SYS_FAULT_ECHO_LINK_DOWN:
4475 Echo the inverted Ethernet link state to the fault LED.
4477 Note: If this option is active, then CONFIG_SYS_FAULT_MII_ADDR
4478 also needs to be defined.
4480 - CONFIG_SYS_FAULT_MII_ADDR:
4481 MII address of the PHY to check for the Ethernet link state.
4483 - CONFIG_NS16550_MIN_FUNCTIONS:
4484 Define this if you desire to only have use of the NS16550_init
4485 and NS16550_putc functions for the serial driver located at
4486 drivers/serial/ns16550.c. This option is useful for saving
4487 space for already greatly restricted images, including but not
4488 limited to NAND_SPL configurations.
4490 - CONFIG_DISPLAY_BOARDINFO
4491 Display information about the board that U-Boot is running on
4492 when U-Boot starts up. The board function checkboard() is called
4495 - CONFIG_DISPLAY_BOARDINFO_LATE
4496 Similar to the previous option, but display this information
4497 later, once stdio is running and output goes to the LCD, if
4500 - CONFIG_BOARD_SIZE_LIMIT:
4501 Maximum size of the U-Boot image. When defined, the
4502 build system checks that the actual size does not
4505 Low Level (hardware related) configuration options:
4506 ---------------------------------------------------
4508 - CONFIG_SYS_CACHELINE_SIZE:
4509 Cache Line Size of the CPU.
4511 - CONFIG_SYS_DEFAULT_IMMR:
4512 Default address of the IMMR after system reset.
4514 Needed on some 8260 systems (MPC8260ADS, PQ2FADS-ZU,
4515 and RPXsuper) to be able to adjust the position of
4516 the IMMR register after a reset.
4518 - CONFIG_SYS_CCSRBAR_DEFAULT:
4519 Default (power-on reset) physical address of CCSR on Freescale
4522 - CONFIG_SYS_CCSRBAR:
4523 Virtual address of CCSR. On a 32-bit build, this is typically
4524 the same value as CONFIG_SYS_CCSRBAR_DEFAULT.
4526 CONFIG_SYS_DEFAULT_IMMR must also be set to this value,
4527 for cross-platform code that uses that macro instead.
4529 - CONFIG_SYS_CCSRBAR_PHYS:
4530 Physical address of CCSR. CCSR can be relocated to a new
4531 physical address, if desired. In this case, this macro should
4532 be set to that address. Otherwise, it should be set to the
4533 same value as CONFIG_SYS_CCSRBAR_DEFAULT. For example, CCSR
4534 is typically relocated on 36-bit builds. It is recommended
4535 that this macro be defined via the _HIGH and _LOW macros:
4537 #define CONFIG_SYS_CCSRBAR_PHYS ((CONFIG_SYS_CCSRBAR_PHYS_HIGH
4538 * 1ull) << 32 | CONFIG_SYS_CCSRBAR_PHYS_LOW)
4540 - CONFIG_SYS_CCSRBAR_PHYS_HIGH:
4541 Bits 33-36 of CONFIG_SYS_CCSRBAR_PHYS. This value is typically
4542 either 0 (32-bit build) or 0xF (36-bit build). This macro is
4543 used in assembly code, so it must not contain typecasts or
4544 integer size suffixes (e.g. "ULL").
4546 - CONFIG_SYS_CCSRBAR_PHYS_LOW:
4547 Lower 32-bits of CONFIG_SYS_CCSRBAR_PHYS. This macro is
4548 used in assembly code, so it must not contain typecasts or
4549 integer size suffixes (e.g. "ULL").
4551 - CONFIG_SYS_CCSR_DO_NOT_RELOCATE:
4552 If this macro is defined, then CONFIG_SYS_CCSRBAR_PHYS will be
4553 forced to a value that ensures that CCSR is not relocated.
4555 - Floppy Disk Support:
4556 CONFIG_SYS_FDC_DRIVE_NUMBER
4558 the default drive number (default value 0)
4560 CONFIG_SYS_ISA_IO_STRIDE
4562 defines the spacing between FDC chipset registers
4565 CONFIG_SYS_ISA_IO_OFFSET
4567 defines the offset of register from address. It
4568 depends on which part of the data bus is connected to
4569 the FDC chipset. (default value 0)
4571 If CONFIG_SYS_ISA_IO_STRIDE CONFIG_SYS_ISA_IO_OFFSET and
4572 CONFIG_SYS_FDC_DRIVE_NUMBER are undefined, they take their
4575 if CONFIG_SYS_FDC_HW_INIT is defined, then the function
4576 fdc_hw_init() is called at the beginning of the FDC
4577 setup. fdc_hw_init() must be provided by the board
4578 source code. It is used to make hardware dependant
4582 Most IDE controllers were designed to be connected with PCI
4583 interface. Only few of them were designed for AHB interface.
4584 When software is doing ATA command and data transfer to
4585 IDE devices through IDE-AHB controller, some additional
4586 registers accessing to these kind of IDE-AHB controller
4589 - CONFIG_SYS_IMMR: Physical address of the Internal Memory.
4590 DO NOT CHANGE unless you know exactly what you're
4591 doing! (11-4) [MPC8xx/82xx systems only]
4593 - CONFIG_SYS_INIT_RAM_ADDR:
4595 Start address of memory area that can be used for
4596 initial data and stack; please note that this must be
4597 writable memory that is working WITHOUT special
4598 initialization, i. e. you CANNOT use normal RAM which
4599 will become available only after programming the
4600 memory controller and running certain initialization
4603 U-Boot uses the following memory types:
4604 - MPC8xx and MPC8260: IMMR (internal memory of the CPU)
4605 - MPC824X: data cache
4606 - PPC4xx: data cache
4608 - CONFIG_SYS_GBL_DATA_OFFSET:
4610 Offset of the initial data structure in the memory
4611 area defined by CONFIG_SYS_INIT_RAM_ADDR. Usually
4612 CONFIG_SYS_GBL_DATA_OFFSET is chosen such that the initial
4613 data is located at the end of the available space
4614 (sometimes written as (CONFIG_SYS_INIT_RAM_SIZE -
4615 CONFIG_SYS_INIT_DATA_SIZE), and the initial stack is just
4616 below that area (growing from (CONFIG_SYS_INIT_RAM_ADDR +
4617 CONFIG_SYS_GBL_DATA_OFFSET) downward.
4620 On the MPC824X (or other systems that use the data
4621 cache for initial memory) the address chosen for
4622 CONFIG_SYS_INIT_RAM_ADDR is basically arbitrary - it must
4623 point to an otherwise UNUSED address space between
4624 the top of RAM and the start of the PCI space.
4626 - CONFIG_SYS_SIUMCR: SIU Module Configuration (11-6)
4628 - CONFIG_SYS_SYPCR: System Protection Control (11-9)
4630 - CONFIG_SYS_TBSCR: Time Base Status and Control (11-26)
4632 - CONFIG_SYS_PISCR: Periodic Interrupt Status and Control (11-31)
4634 - CONFIG_SYS_PLPRCR: PLL, Low-Power, and Reset Control Register (15-30)
4636 - CONFIG_SYS_SCCR: System Clock and reset Control Register (15-27)
4638 - CONFIG_SYS_OR_TIMING_SDRAM:
4641 - CONFIG_SYS_MAMR_PTA:
4642 periodic timer for refresh
4644 - CONFIG_SYS_DER: Debug Event Register (37-47)
4646 - FLASH_BASE0_PRELIM, FLASH_BASE1_PRELIM, CONFIG_SYS_REMAP_OR_AM,
4647 CONFIG_SYS_PRELIM_OR_AM, CONFIG_SYS_OR_TIMING_FLASH, CONFIG_SYS_OR0_REMAP,
4648 CONFIG_SYS_OR0_PRELIM, CONFIG_SYS_BR0_PRELIM, CONFIG_SYS_OR1_REMAP, CONFIG_SYS_OR1_PRELIM,
4649 CONFIG_SYS_BR1_PRELIM:
4650 Memory Controller Definitions: BR0/1 and OR0/1 (FLASH)
4652 - SDRAM_BASE2_PRELIM, SDRAM_BASE3_PRELIM, SDRAM_MAX_SIZE,
4653 CONFIG_SYS_OR_TIMING_SDRAM, CONFIG_SYS_OR2_PRELIM, CONFIG_SYS_BR2_PRELIM,
4654 CONFIG_SYS_OR3_PRELIM, CONFIG_SYS_BR3_PRELIM:
4655 Memory Controller Definitions: BR2/3 and OR2/3 (SDRAM)
4657 - CONFIG_SYS_MAMR_PTA, CONFIG_SYS_MPTPR_2BK_4K, CONFIG_SYS_MPTPR_1BK_4K, CONFIG_SYS_MPTPR_2BK_8K,
4658 CONFIG_SYS_MPTPR_1BK_8K, CONFIG_SYS_MAMR_8COL, CONFIG_SYS_MAMR_9COL:
4659 Machine Mode Register and Memory Periodic Timer
4660 Prescaler definitions (SDRAM timing)
4662 - CONFIG_SYS_I2C_UCODE_PATCH, CONFIG_SYS_I2C_DPMEM_OFFSET [0x1FC0]:
4663 enable I2C microcode relocation patch (MPC8xx);
4664 define relocation offset in DPRAM [DSP2]
4666 - CONFIG_SYS_SMC_UCODE_PATCH, CONFIG_SYS_SMC_DPMEM_OFFSET [0x1FC0]:
4667 enable SMC microcode relocation patch (MPC8xx);
4668 define relocation offset in DPRAM [SMC1]
4670 - CONFIG_SYS_SPI_UCODE_PATCH, CONFIG_SYS_SPI_DPMEM_OFFSET [0x1FC0]:
4671 enable SPI microcode relocation patch (MPC8xx);
4672 define relocation offset in DPRAM [SCC4]
4674 - CONFIG_SYS_USE_OSCCLK:
4675 Use OSCM clock mode on MBX8xx board. Be careful,
4676 wrong setting might damage your board. Read
4677 doc/README.MBX before setting this variable!
4679 - CONFIG_SYS_CPM_POST_WORD_ADDR: (MPC8xx, MPC8260 only)
4680 Offset of the bootmode word in DPRAM used by post
4681 (Power On Self Tests). This definition overrides
4682 #define'd default value in commproc.h resp.
4685 - CONFIG_SYS_PCI_SLV_MEM_LOCAL, CONFIG_SYS_PCI_SLV_MEM_BUS, CONFIG_SYS_PICMR0_MASK_ATTRIB,
4686 CONFIG_SYS_PCI_MSTR0_LOCAL, CONFIG_SYS_PCIMSK0_MASK, CONFIG_SYS_PCI_MSTR1_LOCAL,
4687 CONFIG_SYS_PCIMSK1_MASK, CONFIG_SYS_PCI_MSTR_MEM_LOCAL, CONFIG_SYS_PCI_MSTR_MEM_BUS,
4688 CONFIG_SYS_CPU_PCI_MEM_START, CONFIG_SYS_PCI_MSTR_MEM_SIZE, CONFIG_SYS_POCMR0_MASK_ATTRIB,
4689 CONFIG_SYS_PCI_MSTR_MEMIO_LOCAL, CONFIG_SYS_PCI_MSTR_MEMIO_BUS, CPU_PCI_MEMIO_START,
4690 CONFIG_SYS_PCI_MSTR_MEMIO_SIZE, CONFIG_SYS_POCMR1_MASK_ATTRIB, CONFIG_SYS_PCI_MSTR_IO_LOCAL,
4691 CONFIG_SYS_PCI_MSTR_IO_BUS, CONFIG_SYS_CPU_PCI_IO_START, CONFIG_SYS_PCI_MSTR_IO_SIZE,
4692 CONFIG_SYS_POCMR2_MASK_ATTRIB: (MPC826x only)
4693 Overrides the default PCI memory map in arch/powerpc/cpu/mpc8260/pci.c if set.
4695 - CONFIG_PCI_DISABLE_PCIE:
4696 Disable PCI-Express on systems where it is supported but not
4699 - CONFIG_PCI_ENUM_ONLY
4700 Only scan through and get the devices on the busses.
4701 Don't do any setup work, presumably because someone or
4702 something has already done it, and we don't need to do it
4703 a second time. Useful for platforms that are pre-booted
4704 by coreboot or similar.
4706 - CONFIG_PCI_INDIRECT_BRIDGE:
4707 Enable support for indirect PCI bridges.
4710 Chip has SRIO or not
4713 Board has SRIO 1 port available
4716 Board has SRIO 2 port available
4718 - CONFIG_SRIO_PCIE_BOOT_MASTER
4719 Board can support master function for Boot from SRIO and PCIE
4721 - CONFIG_SYS_SRIOn_MEM_VIRT:
4722 Virtual Address of SRIO port 'n' memory region
4724 - CONFIG_SYS_SRIOn_MEM_PHYS:
4725 Physical Address of SRIO port 'n' memory region
4727 - CONFIG_SYS_SRIOn_MEM_SIZE:
4728 Size of SRIO port 'n' memory region
4730 - CONFIG_SYS_NAND_BUSWIDTH_16BIT
4731 Defined to tell the NAND controller that the NAND chip is using
4733 Not all NAND drivers use this symbol.
4734 Example of drivers that use it:
4735 - drivers/mtd/nand/ndfc.c
4736 - drivers/mtd/nand/mxc_nand.c
4738 - CONFIG_SYS_NDFC_EBC0_CFG
4739 Sets the EBC0_CFG register for the NDFC. If not defined
4740 a default value will be used.
4743 Get DDR timing information from an I2C EEPROM. Common
4744 with pluggable memory modules such as SODIMMs
4747 I2C address of the SPD EEPROM
4749 - CONFIG_SYS_SPD_BUS_NUM
4750 If SPD EEPROM is on an I2C bus other than the first
4751 one, specify here. Note that the value must resolve
4752 to something your driver can deal with.
4754 - CONFIG_SYS_DDR_RAW_TIMING
4755 Get DDR timing information from other than SPD. Common with
4756 soldered DDR chips onboard without SPD. DDR raw timing
4757 parameters are extracted from datasheet and hard-coded into
4758 header files or board specific files.
4760 - CONFIG_FSL_DDR_INTERACTIVE
4761 Enable interactive DDR debugging. See doc/README.fsl-ddr.
4763 - CONFIG_SYS_83XX_DDR_USES_CS0
4764 Only for 83xx systems. If specified, then DDR should
4765 be configured using CS0 and CS1 instead of CS2 and CS3.
4767 - CONFIG_ETHER_ON_FEC[12]
4768 Define to enable FEC[12] on a 8xx series processor.
4770 - CONFIG_FEC[12]_PHY
4771 Define to the hardcoded PHY address which corresponds
4772 to the given FEC; i. e.
4773 #define CONFIG_FEC1_PHY 4
4774 means that the PHY with address 4 is connected to FEC1
4776 When set to -1, means to probe for first available.
4778 - CONFIG_FEC[12]_PHY_NORXERR
4779 The PHY does not have a RXERR line (RMII only).
4780 (so program the FEC to ignore it).
4783 Enable RMII mode for all FECs.
4784 Note that this is a global option, we can't
4785 have one FEC in standard MII mode and another in RMII mode.
4787 - CONFIG_CRC32_VERIFY
4788 Add a verify option to the crc32 command.
4791 => crc32 -v <address> <count> <crc32>
4793 Where address/count indicate a memory area
4794 and crc32 is the correct crc32 which the
4798 Add the "loopw" memory command. This only takes effect if
4799 the memory commands are activated globally (CONFIG_CMD_MEM).
4802 Add the "mdc" and "mwc" memory commands. These are cyclic
4807 This command will print 4 bytes (10,11,12,13) each 500 ms.
4809 => mwc.l 100 12345678 10
4810 This command will write 12345678 to address 100 all 10 ms.
4812 This only takes effect if the memory commands are activated
4813 globally (CONFIG_CMD_MEM).
4815 - CONFIG_SKIP_LOWLEVEL_INIT
4816 [ARM, NDS32, MIPS only] If this variable is defined, then certain
4817 low level initializations (like setting up the memory
4818 controller) are omitted and/or U-Boot does not
4819 relocate itself into RAM.
4821 Normally this variable MUST NOT be defined. The only
4822 exception is when U-Boot is loaded (to RAM) by some
4823 other boot loader or by a debugger which performs
4824 these initializations itself.
4827 Modifies the behaviour of start.S when compiling a loader
4828 that is executed before the actual U-Boot. E.g. when
4829 compiling a NAND SPL.
4832 Modifies the behaviour of start.S when compiling a loader
4833 that is executed after the SPL and before the actual U-Boot.
4834 It is loaded by the SPL.
4836 - CONFIG_SYS_MPC85XX_NO_RESETVEC
4837 Only for 85xx systems. If this variable is specified, the section
4838 .resetvec is not kept and the section .bootpg is placed in the
4839 previous 4k of the .text section.
4841 - CONFIG_ARCH_MAP_SYSMEM
4842 Generally U-Boot (and in particular the md command) uses
4843 effective address. It is therefore not necessary to regard
4844 U-Boot address as virtual addresses that need to be translated
4845 to physical addresses. However, sandbox requires this, since
4846 it maintains its own little RAM buffer which contains all
4847 addressable memory. This option causes some memory accesses
4848 to be mapped through map_sysmem() / unmap_sysmem().
4850 - CONFIG_USE_ARCH_MEMCPY
4851 CONFIG_USE_ARCH_MEMSET
4852 If these options are used a optimized version of memcpy/memset will
4853 be used if available. These functions may be faster under some
4854 conditions but may increase the binary size.
4856 - CONFIG_X86_RESET_VECTOR
4857 If defined, the x86 reset vector code is included. This is not
4858 needed when U-Boot is running from Coreboot.
4861 Defines the MPU clock speed (in MHz).
4863 NOTE : currently only supported on AM335x platforms.
4865 - CONFIG_SPL_AM33XX_ENABLE_RTC32K_OSC:
4866 Enables the RTC32K OSC on AM33xx based plattforms
4868 - CONFIG_SYS_NAND_NO_SUBPAGE_WRITE
4869 Option to disable subpage write in NAND driver
4870 driver that uses this:
4871 drivers/mtd/nand/davinci_nand.c
4873 Freescale QE/FMAN Firmware Support:
4874 -----------------------------------
4876 The Freescale QUICCEngine (QE) and Frame Manager (FMAN) both support the
4877 loading of "firmware", which is encoded in the QE firmware binary format.
4878 This firmware often needs to be loaded during U-Boot booting, so macros
4879 are used to identify the storage device (NOR flash, SPI, etc) and the address
4882 - CONFIG_SYS_FMAN_FW_ADDR
4883 The address in the storage device where the FMAN microcode is located. The
4884 meaning of this address depends on which CONFIG_SYS_QE_FW_IN_xxx macro
4887 - CONFIG_SYS_QE_FW_ADDR
4888 The address in the storage device where the QE microcode is located. The
4889 meaning of this address depends on which CONFIG_SYS_QE_FW_IN_xxx macro
4892 - CONFIG_SYS_QE_FMAN_FW_LENGTH
4893 The maximum possible size of the firmware. The firmware binary format
4894 has a field that specifies the actual size of the firmware, but it
4895 might not be possible to read any part of the firmware unless some
4896 local storage is allocated to hold the entire firmware first.
4898 - CONFIG_SYS_QE_FMAN_FW_IN_NOR
4899 Specifies that QE/FMAN firmware is located in NOR flash, mapped as
4900 normal addressable memory via the LBC. CONFIG_SYS_FMAN_FW_ADDR is the
4901 virtual address in NOR flash.
4903 - CONFIG_SYS_QE_FMAN_FW_IN_NAND
4904 Specifies that QE/FMAN firmware is located in NAND flash.
4905 CONFIG_SYS_FMAN_FW_ADDR is the offset within NAND flash.
4907 - CONFIG_SYS_QE_FMAN_FW_IN_MMC
4908 Specifies that QE/FMAN firmware is located on the primary SD/MMC
4909 device. CONFIG_SYS_FMAN_FW_ADDR is the byte offset on that device.
4911 - CONFIG_SYS_QE_FMAN_FW_IN_SPIFLASH
4912 Specifies that QE/FMAN firmware is located on the primary SPI
4913 device. CONFIG_SYS_FMAN_FW_ADDR is the byte offset on that device.
4915 - CONFIG_SYS_QE_FMAN_FW_IN_REMOTE
4916 Specifies that QE/FMAN firmware is located in the remote (master)
4917 memory space. CONFIG_SYS_FMAN_FW_ADDR is a virtual address which
4918 can be mapped from slave TLB->slave LAW->slave SRIO or PCIE outbound
4919 window->master inbound window->master LAW->the ucode address in
4920 master's memory space.
4922 Freescale Layerscape Management Complex Firmware Support:
4923 ---------------------------------------------------------
4924 The Freescale Layerscape Management Complex (MC) supports the loading of
4926 This firmware often needs to be loaded during U-Boot booting, so macros
4927 are used to identify the storage device (NOR flash, SPI, etc) and the address
4930 - CONFIG_FSL_MC_ENET
4931 Enable the MC driver for Layerscape SoCs.
4933 - CONFIG_SYS_LS_MC_FW_ADDR
4934 The address in the storage device where the firmware is located. The
4935 meaning of this address depends on which CONFIG_SYS_LS_MC_FW_IN_xxx macro
4938 - CONFIG_SYS_LS_MC_FW_LENGTH
4939 The maximum possible size of the firmware. The firmware binary format
4940 has a field that specifies the actual size of the firmware, but it
4941 might not be possible to read any part of the firmware unless some
4942 local storage is allocated to hold the entire firmware first.
4944 - CONFIG_SYS_LS_MC_FW_IN_NOR
4945 Specifies that MC firmware is located in NOR flash, mapped as
4946 normal addressable memory via the LBC. CONFIG_SYS_LS_MC_FW_ADDR is the
4947 virtual address in NOR flash.
4949 Building the Software:
4950 ======================
4952 Building U-Boot has been tested in several native build environments
4953 and in many different cross environments. Of course we cannot support
4954 all possibly existing versions of cross development tools in all
4955 (potentially obsolete) versions. In case of tool chain problems we
4956 recommend to use the ELDK (see http://www.denx.de/wiki/DULG/ELDK)
4957 which is extensively used to build and test U-Boot.
4959 If you are not using a native environment, it is assumed that you
4960 have GNU cross compiling tools available in your path. In this case,
4961 you must set the environment variable CROSS_COMPILE in your shell.
4962 Note that no changes to the Makefile or any other source files are
4963 necessary. For example using the ELDK on a 4xx CPU, please enter:
4965 $ CROSS_COMPILE=ppc_4xx-
4966 $ export CROSS_COMPILE
4968 Note: If you wish to generate Windows versions of the utilities in
4969 the tools directory you can use the MinGW toolchain
4970 (http://www.mingw.org). Set your HOST tools to the MinGW
4971 toolchain and execute 'make tools'. For example:
4973 $ make HOSTCC=i586-mingw32msvc-gcc HOSTSTRIP=i586-mingw32msvc-strip tools
4975 Binaries such as tools/mkimage.exe will be created which can
4976 be executed on computers running Windows.
4978 U-Boot is intended to be simple to build. After installing the
4979 sources you must configure U-Boot for one specific board type. This
4984 where "NAME_defconfig" is the name of one of the existing configu-
4985 rations; see boards.cfg for supported names.
4987 Note: for some board special configuration names may exist; check if
4988 additional information is available from the board vendor; for
4989 instance, the TQM823L systems are available without (standard)
4990 or with LCD support. You can select such additional "features"
4991 when choosing the configuration, i. e.
4993 make TQM823L_defconfig
4994 - will configure for a plain TQM823L, i. e. no LCD support
4996 make TQM823L_LCD_defconfig
4997 - will configure for a TQM823L with U-Boot console on LCD
5002 Finally, type "make all", and you should get some working U-Boot
5003 images ready for download to / installation on your system:
5005 - "u-boot.bin" is a raw binary image
5006 - "u-boot" is an image in ELF binary format
5007 - "u-boot.srec" is in Motorola S-Record format
5009 By default the build is performed locally and the objects are saved
5010 in the source directory. One of the two methods can be used to change
5011 this behavior and build U-Boot to some external directory:
5013 1. Add O= to the make command line invocations:
5015 make O=/tmp/build distclean
5016 make O=/tmp/build NAME_defconfig
5017 make O=/tmp/build all
5019 2. Set environment variable KBUILD_OUTPUT to point to the desired location:
5021 export KBUILD_OUTPUT=/tmp/build
5026 Note that the command line "O=" setting overrides the KBUILD_OUTPUT environment
5030 Please be aware that the Makefiles assume you are using GNU make, so
5031 for instance on NetBSD you might need to use "gmake" instead of
5035 If the system board that you have is not listed, then you will need
5036 to port U-Boot to your hardware platform. To do this, follow these
5039 1. Add a new configuration option for your board to the toplevel
5040 "boards.cfg" file, using the existing entries as examples.
5041 Follow the instructions there to keep the boards in order.
5042 2. Create a new directory to hold your board specific code. Add any
5043 files you need. In your board directory, you will need at least
5044 the "Makefile", a "<board>.c", "flash.c" and "u-boot.lds".
5045 3. Create a new configuration file "include/configs/<board>.h" for
5047 3. If you're porting U-Boot to a new CPU, then also create a new
5048 directory to hold your CPU specific code. Add any files you need.
5049 4. Run "make <board>_defconfig" with your new name.
5050 5. Type "make", and you should get a working "u-boot.srec" file
5051 to be installed on your target system.
5052 6. Debug and solve any problems that might arise.
5053 [Of course, this last step is much harder than it sounds.]
5056 Testing of U-Boot Modifications, Ports to New Hardware, etc.:
5057 ==============================================================
5059 If you have modified U-Boot sources (for instance added a new board
5060 or support for new devices, a new CPU, etc.) you are expected to
5061 provide feedback to the other developers. The feedback normally takes
5062 the form of a "patch", i. e. a context diff against a certain (latest
5063 official or latest in the git repository) version of U-Boot sources.
5065 But before you submit such a patch, please verify that your modifi-
5066 cation did not break existing code. At least make sure that *ALL* of
5067 the supported boards compile WITHOUT ANY compiler warnings. To do so,
5068 just run the "MAKEALL" script, which will configure and build U-Boot
5069 for ALL supported system. Be warned, this will take a while. You can
5070 select which (cross) compiler to use by passing a `CROSS_COMPILE'
5071 environment variable to the script, i. e. to use the ELDK cross tools
5074 CROSS_COMPILE=ppc_8xx- MAKEALL
5076 or to build on a native PowerPC system you can type
5078 CROSS_COMPILE=' ' MAKEALL
5080 When using the MAKEALL script, the default behaviour is to build
5081 U-Boot in the source directory. This location can be changed by
5082 setting the BUILD_DIR environment variable. Also, for each target
5083 built, the MAKEALL script saves two log files (<target>.ERR and
5084 <target>.MAKEALL) in the <source dir>/LOG directory. This default
5085 location can be changed by setting the MAKEALL_LOGDIR environment
5086 variable. For example:
5088 export BUILD_DIR=/tmp/build
5089 export MAKEALL_LOGDIR=/tmp/log
5090 CROSS_COMPILE=ppc_8xx- MAKEALL
5092 With the above settings build objects are saved in the /tmp/build,
5093 log files are saved in the /tmp/log and the source tree remains clean
5094 during the whole build process.
5097 See also "U-Boot Porting Guide" below.
5100 Monitor Commands - Overview:
5101 ============================
5103 go - start application at address 'addr'
5104 run - run commands in an environment variable
5105 bootm - boot application image from memory
5106 bootp - boot image via network using BootP/TFTP protocol
5107 bootz - boot zImage from memory
5108 tftpboot- boot image via network using TFTP protocol
5109 and env variables "ipaddr" and "serverip"
5110 (and eventually "gatewayip")
5111 tftpput - upload a file via network using TFTP protocol
5112 rarpboot- boot image via network using RARP/TFTP protocol
5113 diskboot- boot from IDE devicebootd - boot default, i.e., run 'bootcmd'
5114 loads - load S-Record file over serial line
5115 loadb - load binary file over serial line (kermit mode)
5117 mm - memory modify (auto-incrementing)
5118 nm - memory modify (constant address)
5119 mw - memory write (fill)
5121 cmp - memory compare
5122 crc32 - checksum calculation
5123 i2c - I2C sub-system
5124 sspi - SPI utility commands
5125 base - print or set address offset
5126 printenv- print environment variables
5127 setenv - set environment variables
5128 saveenv - save environment variables to persistent storage
5129 protect - enable or disable FLASH write protection
5130 erase - erase FLASH memory
5131 flinfo - print FLASH memory information
5132 nand - NAND memory operations (see doc/README.nand)
5133 bdinfo - print Board Info structure
5134 iminfo - print header information for application image
5135 coninfo - print console devices and informations
5136 ide - IDE sub-system
5137 loop - infinite loop on address range
5138 loopw - infinite write loop on address range
5139 mtest - simple RAM test
5140 icache - enable or disable instruction cache
5141 dcache - enable or disable data cache
5142 reset - Perform RESET of the CPU
5143 echo - echo args to console
5144 version - print monitor version
5145 help - print online help
5146 ? - alias for 'help'
5149 Monitor Commands - Detailed Description:
5150 ========================================
5154 For now: just type "help <command>".
5157 Environment Variables:
5158 ======================
5160 U-Boot supports user configuration using Environment Variables which
5161 can be made persistent by saving to Flash memory.
5163 Environment Variables are set using "setenv", printed using
5164 "printenv", and saved to Flash using "saveenv". Using "setenv"
5165 without a value can be used to delete a variable from the
5166 environment. As long as you don't save the environment you are
5167 working with an in-memory copy. In case the Flash area containing the
5168 environment is erased by accident, a default environment is provided.
5170 Some configuration options can be set using Environment Variables.
5172 List of environment variables (most likely not complete):
5174 baudrate - see CONFIG_BAUDRATE
5176 bootdelay - see CONFIG_BOOTDELAY
5178 bootcmd - see CONFIG_BOOTCOMMAND
5180 bootargs - Boot arguments when booting an RTOS image
5182 bootfile - Name of the image to load with TFTP
5184 bootm_low - Memory range available for image processing in the bootm
5185 command can be restricted. This variable is given as
5186 a hexadecimal number and defines lowest address allowed
5187 for use by the bootm command. See also "bootm_size"
5188 environment variable. Address defined by "bootm_low" is
5189 also the base of the initial memory mapping for the Linux
5190 kernel -- see the description of CONFIG_SYS_BOOTMAPSZ and
5193 bootm_mapsize - Size of the initial memory mapping for the Linux kernel.
5194 This variable is given as a hexadecimal number and it
5195 defines the size of the memory region starting at base
5196 address bootm_low that is accessible by the Linux kernel
5197 during early boot. If unset, CONFIG_SYS_BOOTMAPSZ is used
5198 as the default value if it is defined, and bootm_size is
5201 bootm_size - Memory range available for image processing in the bootm
5202 command can be restricted. This variable is given as
5203 a hexadecimal number and defines the size of the region
5204 allowed for use by the bootm command. See also "bootm_low"
5205 environment variable.
5207 updatefile - Location of the software update file on a TFTP server, used
5208 by the automatic software update feature. Please refer to
5209 documentation in doc/README.update for more details.
5211 autoload - if set to "no" (any string beginning with 'n'),
5212 "bootp" will just load perform a lookup of the
5213 configuration from the BOOTP server, but not try to
5214 load any image using TFTP
5216 autostart - if set to "yes", an image loaded using the "bootp",
5217 "rarpboot", "tftpboot" or "diskboot" commands will
5218 be automatically started (by internally calling
5221 If set to "no", a standalone image passed to the
5222 "bootm" command will be copied to the load address
5223 (and eventually uncompressed), but NOT be started.
5224 This can be used to load and uncompress arbitrary
5227 fdt_high - if set this restricts the maximum address that the
5228 flattened device tree will be copied into upon boot.
5229 For example, if you have a system with 1 GB memory
5230 at physical address 0x10000000, while Linux kernel
5231 only recognizes the first 704 MB as low memory, you
5232 may need to set fdt_high as 0x3C000000 to have the
5233 device tree blob be copied to the maximum address
5234 of the 704 MB low memory, so that Linux kernel can
5235 access it during the boot procedure.
5237 If this is set to the special value 0xFFFFFFFF then
5238 the fdt will not be copied at all on boot. For this
5239 to work it must reside in writable memory, have
5240 sufficient padding on the end of it for u-boot to
5241 add the information it needs into it, and the memory
5242 must be accessible by the kernel.
5244 fdtcontroladdr- if set this is the address of the control flattened
5245 device tree used by U-Boot when CONFIG_OF_CONTROL is
5248 i2cfast - (PPC405GP|PPC405EP only)
5249 if set to 'y' configures Linux I2C driver for fast
5250 mode (400kHZ). This environment variable is used in
5251 initialization code. So, for changes to be effective
5252 it must be saved and board must be reset.
5254 initrd_high - restrict positioning of initrd images:
5255 If this variable is not set, initrd images will be
5256 copied to the highest possible address in RAM; this
5257 is usually what you want since it allows for
5258 maximum initrd size. If for some reason you want to
5259 make sure that the initrd image is loaded below the
5260 CONFIG_SYS_BOOTMAPSZ limit, you can set this environment
5261 variable to a value of "no" or "off" or "0".
5262 Alternatively, you can set it to a maximum upper
5263 address to use (U-Boot will still check that it
5264 does not overwrite the U-Boot stack and data).
5266 For instance, when you have a system with 16 MB
5267 RAM, and want to reserve 4 MB from use by Linux,
5268 you can do this by adding "mem=12M" to the value of
5269 the "bootargs" variable. However, now you must make
5270 sure that the initrd image is placed in the first
5271 12 MB as well - this can be done with
5273 setenv initrd_high 00c00000
5275 If you set initrd_high to 0xFFFFFFFF, this is an
5276 indication to U-Boot that all addresses are legal
5277 for the Linux kernel, including addresses in flash
5278 memory. In this case U-Boot will NOT COPY the
5279 ramdisk at all. This may be useful to reduce the
5280 boot time on your system, but requires that this
5281 feature is supported by your Linux kernel.
5283 ipaddr - IP address; needed for tftpboot command
5285 loadaddr - Default load address for commands like "bootp",
5286 "rarpboot", "tftpboot", "loadb" or "diskboot"
5288 loads_echo - see CONFIG_LOADS_ECHO
5290 serverip - TFTP server IP address; needed for tftpboot command
5292 bootretry - see CONFIG_BOOT_RETRY_TIME
5294 bootdelaykey - see CONFIG_AUTOBOOT_DELAY_STR
5296 bootstopkey - see CONFIG_AUTOBOOT_STOP_STR
5298 ethprime - controls which interface is used first.
5300 ethact - controls which interface is currently active.
5301 For example you can do the following
5303 => setenv ethact FEC
5304 => ping 192.168.0.1 # traffic sent on FEC
5305 => setenv ethact SCC
5306 => ping 10.0.0.1 # traffic sent on SCC
5308 ethrotate - When set to "no" U-Boot does not go through all
5309 available network interfaces.
5310 It just stays at the currently selected interface.
5312 netretry - When set to "no" each network operation will
5313 either succeed or fail without retrying.
5314 When set to "once" the network operation will
5315 fail when all the available network interfaces
5316 are tried once without success.
5317 Useful on scripts which control the retry operation
5320 npe_ucode - set load address for the NPE microcode
5322 silent_linux - If set then linux will be told to boot silently, by
5323 changing the console to be empty. If "yes" it will be
5324 made silent. If "no" it will not be made silent. If
5325 unset, then it will be made silent if the U-Boot console
5328 tftpsrcport - If this is set, the value is used for TFTP's
5331 tftpdstport - If this is set, the value is used for TFTP's UDP
5332 destination port instead of the Well Know Port 69.
5334 tftpblocksize - Block size to use for TFTP transfers; if not set,
5335 we use the TFTP server's default block size
5337 tftptimeout - Retransmission timeout for TFTP packets (in milli-
5338 seconds, minimum value is 1000 = 1 second). Defines
5339 when a packet is considered to be lost so it has to
5340 be retransmitted. The default is 5000 = 5 seconds.
5341 Lowering this value may make downloads succeed
5342 faster in networks with high packet loss rates or
5343 with unreliable TFTP servers.
5345 vlan - When set to a value < 4095 the traffic over
5346 Ethernet is encapsulated/received over 802.1q
5349 The following image location variables contain the location of images
5350 used in booting. The "Image" column gives the role of the image and is
5351 not an environment variable name. The other columns are environment
5352 variable names. "File Name" gives the name of the file on a TFTP
5353 server, "RAM Address" gives the location in RAM the image will be
5354 loaded to, and "Flash Location" gives the image's address in NOR
5355 flash or offset in NAND flash.
5357 *Note* - these variables don't have to be defined for all boards, some
5358 boards currenlty use other variables for these purposes, and some
5359 boards use these variables for other purposes.
5361 Image File Name RAM Address Flash Location
5362 ----- --------- ----------- --------------
5363 u-boot u-boot u-boot_addr_r u-boot_addr
5364 Linux kernel bootfile kernel_addr_r kernel_addr
5365 device tree blob fdtfile fdt_addr_r fdt_addr
5366 ramdisk ramdiskfile ramdisk_addr_r ramdisk_addr
5368 The following environment variables may be used and automatically
5369 updated by the network boot commands ("bootp" and "rarpboot"),
5370 depending the information provided by your boot server:
5372 bootfile - see above
5373 dnsip - IP address of your Domain Name Server
5374 dnsip2 - IP address of your secondary Domain Name Server
5375 gatewayip - IP address of the Gateway (Router) to use
5376 hostname - Target hostname
5378 netmask - Subnet Mask
5379 rootpath - Pathname of the root filesystem on the NFS server
5380 serverip - see above
5383 There are two special Environment Variables:
5385 serial# - contains hardware identification information such
5386 as type string and/or serial number
5387 ethaddr - Ethernet address
5389 These variables can be set only once (usually during manufacturing of
5390 the board). U-Boot refuses to delete or overwrite these variables
5391 once they have been set once.
5394 Further special Environment Variables:
5396 ver - Contains the U-Boot version string as printed
5397 with the "version" command. This variable is
5398 readonly (see CONFIG_VERSION_VARIABLE).
5401 Please note that changes to some configuration parameters may take
5402 only effect after the next boot (yes, that's just like Windoze :-).
5405 Callback functions for environment variables:
5406 ---------------------------------------------
5408 For some environment variables, the behavior of u-boot needs to change
5409 when their values are changed. This functionailty allows functions to
5410 be associated with arbitrary variables. On creation, overwrite, or
5411 deletion, the callback will provide the opportunity for some side
5412 effect to happen or for the change to be rejected.
5414 The callbacks are named and associated with a function using the
5415 U_BOOT_ENV_CALLBACK macro in your board or driver code.
5417 These callbacks are associated with variables in one of two ways. The
5418 static list can be added to by defining CONFIG_ENV_CALLBACK_LIST_STATIC
5419 in the board configuration to a string that defines a list of
5420 associations. The list must be in the following format:
5422 entry = variable_name[:callback_name]
5425 If the callback name is not specified, then the callback is deleted.
5426 Spaces are also allowed anywhere in the list.
5428 Callbacks can also be associated by defining the ".callbacks" variable
5429 with the same list format above. Any association in ".callbacks" will
5430 override any association in the static list. You can define
5431 CONFIG_ENV_CALLBACK_LIST_DEFAULT to a list (string) to define the
5432 ".callbacks" envirnoment variable in the default or embedded environment.
5435 Command Line Parsing:
5436 =====================
5438 There are two different command line parsers available with U-Boot:
5439 the old "simple" one, and the much more powerful "hush" shell:
5441 Old, simple command line parser:
5442 --------------------------------
5444 - supports environment variables (through setenv / saveenv commands)
5445 - several commands on one line, separated by ';'
5446 - variable substitution using "... ${name} ..." syntax
5447 - special characters ('$', ';') can be escaped by prefixing with '\',
5449 setenv bootcmd bootm \${address}
5450 - You can also escape text by enclosing in single apostrophes, for example:
5451 setenv addip 'setenv bootargs $bootargs ip=$ipaddr:$serverip:$gatewayip:$netmask:$hostname::off'
5456 - similar to Bourne shell, with control structures like
5457 if...then...else...fi, for...do...done; while...do...done,
5458 until...do...done, ...
5459 - supports environment ("global") variables (through setenv / saveenv
5460 commands) and local shell variables (through standard shell syntax
5461 "name=value"); only environment variables can be used with "run"
5467 (1) If a command line (or an environment variable executed by a "run"
5468 command) contains several commands separated by semicolon, and
5469 one of these commands fails, then the remaining commands will be
5472 (2) If you execute several variables with one call to run (i. e.
5473 calling run with a list of variables as arguments), any failing
5474 command will cause "run" to terminate, i. e. the remaining
5475 variables are not executed.
5477 Note for Redundant Ethernet Interfaces:
5478 =======================================
5480 Some boards come with redundant Ethernet interfaces; U-Boot supports
5481 such configurations and is capable of automatic selection of a
5482 "working" interface when needed. MAC assignment works as follows:
5484 Network interfaces are numbered eth0, eth1, eth2, ... Corresponding
5485 MAC addresses can be stored in the environment as "ethaddr" (=>eth0),
5486 "eth1addr" (=>eth1), "eth2addr", ...
5488 If the network interface stores some valid MAC address (for instance
5489 in SROM), this is used as default address if there is NO correspon-
5490 ding setting in the environment; if the corresponding environment
5491 variable is set, this overrides the settings in the card; that means:
5493 o If the SROM has a valid MAC address, and there is no address in the
5494 environment, the SROM's address is used.
5496 o If there is no valid address in the SROM, and a definition in the
5497 environment exists, then the value from the environment variable is
5500 o If both the SROM and the environment contain a MAC address, and
5501 both addresses are the same, this MAC address is used.
5503 o If both the SROM and the environment contain a MAC address, and the
5504 addresses differ, the value from the environment is used and a
5507 o If neither SROM nor the environment contain a MAC address, an error
5510 If Ethernet drivers implement the 'write_hwaddr' function, valid MAC addresses
5511 will be programmed into hardware as part of the initialization process. This
5512 may be skipped by setting the appropriate 'ethmacskip' environment variable.
5513 The naming convention is as follows:
5514 "ethmacskip" (=>eth0), "eth1macskip" (=>eth1) etc.
5519 U-Boot is capable of booting (and performing other auxiliary operations on)
5520 images in two formats:
5522 New uImage format (FIT)
5523 -----------------------
5525 Flexible and powerful format based on Flattened Image Tree -- FIT (similar
5526 to Flattened Device Tree). It allows the use of images with multiple
5527 components (several kernels, ramdisks, etc.), with contents protected by
5528 SHA1, MD5 or CRC32. More details are found in the doc/uImage.FIT directory.
5534 Old image format is based on binary files which can be basically anything,
5535 preceded by a special header; see the definitions in include/image.h for
5536 details; basically, the header defines the following image properties:
5538 * Target Operating System (Provisions for OpenBSD, NetBSD, FreeBSD,
5539 4.4BSD, Linux, SVR4, Esix, Solaris, Irix, SCO, Dell, NCR, VxWorks,
5540 LynxOS, pSOS, QNX, RTEMS, INTEGRITY;
5541 Currently supported: Linux, NetBSD, VxWorks, QNX, RTEMS, LynxOS,
5543 * Target CPU Architecture (Provisions for Alpha, ARM, AVR32, Intel x86,
5544 IA64, MIPS, NDS32, Nios II, PowerPC, IBM S390, SuperH, Sparc, Sparc 64 Bit;
5545 Currently supported: ARM, AVR32, Intel x86, MIPS, NDS32, Nios II, PowerPC).
5546 * Compression Type (uncompressed, gzip, bzip2)
5552 The header is marked by a special Magic Number, and both the header
5553 and the data portions of the image are secured against corruption by
5560 Although U-Boot should support any OS or standalone application
5561 easily, the main focus has always been on Linux during the design of
5564 U-Boot includes many features that so far have been part of some
5565 special "boot loader" code within the Linux kernel. Also, any
5566 "initrd" images to be used are no longer part of one big Linux image;
5567 instead, kernel and "initrd" are separate images. This implementation
5568 serves several purposes:
5570 - the same features can be used for other OS or standalone
5571 applications (for instance: using compressed images to reduce the
5572 Flash memory footprint)
5574 - it becomes much easier to port new Linux kernel versions because
5575 lots of low-level, hardware dependent stuff are done by U-Boot
5577 - the same Linux kernel image can now be used with different "initrd"
5578 images; of course this also means that different kernel images can
5579 be run with the same "initrd". This makes testing easier (you don't
5580 have to build a new "zImage.initrd" Linux image when you just
5581 change a file in your "initrd"). Also, a field-upgrade of the
5582 software is easier now.
5588 Porting Linux to U-Boot based systems:
5589 ---------------------------------------
5591 U-Boot cannot save you from doing all the necessary modifications to
5592 configure the Linux device drivers for use with your target hardware
5593 (no, we don't intend to provide a full virtual machine interface to
5596 But now you can ignore ALL boot loader code (in arch/powerpc/mbxboot).
5598 Just make sure your machine specific header file (for instance
5599 include/asm-ppc/tqm8xx.h) includes the same definition of the Board
5600 Information structure as we define in include/asm-<arch>/u-boot.h,
5601 and make sure that your definition of IMAP_ADDR uses the same value
5602 as your U-Boot configuration in CONFIG_SYS_IMMR.
5604 Note that U-Boot now has a driver model, a unified model for drivers.
5605 If you are adding a new driver, plumb it into driver model. If there
5606 is no uclass available, you are encouraged to create one. See
5610 Configuring the Linux kernel:
5611 -----------------------------
5613 No specific requirements for U-Boot. Make sure you have some root
5614 device (initial ramdisk, NFS) for your target system.
5617 Building a Linux Image:
5618 -----------------------
5620 With U-Boot, "normal" build targets like "zImage" or "bzImage" are
5621 not used. If you use recent kernel source, a new build target
5622 "uImage" will exist which automatically builds an image usable by
5623 U-Boot. Most older kernels also have support for a "pImage" target,
5624 which was introduced for our predecessor project PPCBoot and uses a
5625 100% compatible format.
5629 make TQM850L_defconfig
5634 The "uImage" build target uses a special tool (in 'tools/mkimage') to
5635 encapsulate a compressed Linux kernel image with header information,
5636 CRC32 checksum etc. for use with U-Boot. This is what we are doing:
5638 * build a standard "vmlinux" kernel image (in ELF binary format):
5640 * convert the kernel into a raw binary image:
5642 ${CROSS_COMPILE}-objcopy -O binary \
5643 -R .note -R .comment \
5644 -S vmlinux linux.bin
5646 * compress the binary image:
5650 * package compressed binary image for U-Boot:
5652 mkimage -A ppc -O linux -T kernel -C gzip \
5653 -a 0 -e 0 -n "Linux Kernel Image" \
5654 -d linux.bin.gz uImage
5657 The "mkimage" tool can also be used to create ramdisk images for use
5658 with U-Boot, either separated from the Linux kernel image, or
5659 combined into one file. "mkimage" encapsulates the images with a 64
5660 byte header containing information about target architecture,
5661 operating system, image type, compression method, entry points, time
5662 stamp, CRC32 checksums, etc.
5664 "mkimage" can be called in two ways: to verify existing images and
5665 print the header information, or to build new images.
5667 In the first form (with "-l" option) mkimage lists the information
5668 contained in the header of an existing U-Boot image; this includes
5669 checksum verification:
5671 tools/mkimage -l image
5672 -l ==> list image header information
5674 The second form (with "-d" option) is used to build a U-Boot image
5675 from a "data file" which is used as image payload:
5677 tools/mkimage -A arch -O os -T type -C comp -a addr -e ep \
5678 -n name -d data_file image
5679 -A ==> set architecture to 'arch'
5680 -O ==> set operating system to 'os'
5681 -T ==> set image type to 'type'
5682 -C ==> set compression type 'comp'
5683 -a ==> set load address to 'addr' (hex)
5684 -e ==> set entry point to 'ep' (hex)
5685 -n ==> set image name to 'name'
5686 -d ==> use image data from 'datafile'
5688 Right now, all Linux kernels for PowerPC systems use the same load
5689 address (0x00000000), but the entry point address depends on the
5692 - 2.2.x kernels have the entry point at 0x0000000C,
5693 - 2.3.x and later kernels have the entry point at 0x00000000.
5695 So a typical call to build a U-Boot image would read:
5697 -> tools/mkimage -n '2.4.4 kernel for TQM850L' \
5698 > -A ppc -O linux -T kernel -C gzip -a 0 -e 0 \
5699 > -d /opt/elsk/ppc_8xx/usr/src/linux-2.4.4/arch/powerpc/coffboot/vmlinux.gz \
5700 > examples/uImage.TQM850L
5701 Image Name: 2.4.4 kernel for TQM850L
5702 Created: Wed Jul 19 02:34:59 2000
5703 Image Type: PowerPC Linux Kernel Image (gzip compressed)
5704 Data Size: 335725 Bytes = 327.86 kB = 0.32 MB
5705 Load Address: 0x00000000
5706 Entry Point: 0x00000000
5708 To verify the contents of the image (or check for corruption):
5710 -> tools/mkimage -l examples/uImage.TQM850L
5711 Image Name: 2.4.4 kernel for TQM850L
5712 Created: Wed Jul 19 02:34:59 2000
5713 Image Type: PowerPC Linux Kernel Image (gzip compressed)
5714 Data Size: 335725 Bytes = 327.86 kB = 0.32 MB
5715 Load Address: 0x00000000
5716 Entry Point: 0x00000000
5718 NOTE: for embedded systems where boot time is critical you can trade
5719 speed for memory and install an UNCOMPRESSED image instead: this
5720 needs more space in Flash, but boots much faster since it does not
5721 need to be uncompressed:
5723 -> gunzip /opt/elsk/ppc_8xx/usr/src/linux-2.4.4/arch/powerpc/coffboot/vmlinux.gz
5724 -> tools/mkimage -n '2.4.4 kernel for TQM850L' \
5725 > -A ppc -O linux -T kernel -C none -a 0 -e 0 \
5726 > -d /opt/elsk/ppc_8xx/usr/src/linux-2.4.4/arch/powerpc/coffboot/vmlinux \
5727 > examples/uImage.TQM850L-uncompressed
5728 Image Name: 2.4.4 kernel for TQM850L
5729 Created: Wed Jul 19 02:34:59 2000
5730 Image Type: PowerPC Linux Kernel Image (uncompressed)
5731 Data Size: 792160 Bytes = 773.59 kB = 0.76 MB
5732 Load Address: 0x00000000
5733 Entry Point: 0x00000000
5736 Similar you can build U-Boot images from a 'ramdisk.image.gz' file
5737 when your kernel is intended to use an initial ramdisk:
5739 -> tools/mkimage -n 'Simple Ramdisk Image' \
5740 > -A ppc -O linux -T ramdisk -C gzip \
5741 > -d /LinuxPPC/images/SIMPLE-ramdisk.image.gz examples/simple-initrd
5742 Image Name: Simple Ramdisk Image
5743 Created: Wed Jan 12 14:01:50 2000
5744 Image Type: PowerPC Linux RAMDisk Image (gzip compressed)
5745 Data Size: 566530 Bytes = 553.25 kB = 0.54 MB
5746 Load Address: 0x00000000
5747 Entry Point: 0x00000000
5749 The "dumpimage" is a tool to disassemble images built by mkimage. Its "-i"
5750 option performs the converse operation of the mkimage's second form (the "-d"
5751 option). Given an image built by mkimage, the dumpimage extracts a "data file"
5754 tools/dumpimage -i image -p position data_file
5755 -i ==> extract from the 'image' a specific 'data_file', \
5756 indexed by 'position'
5759 Installing a Linux Image:
5760 -------------------------
5762 To downloading a U-Boot image over the serial (console) interface,
5763 you must convert the image to S-Record format:
5765 objcopy -I binary -O srec examples/image examples/image.srec
5767 The 'objcopy' does not understand the information in the U-Boot
5768 image header, so the resulting S-Record file will be relative to
5769 address 0x00000000. To load it to a given address, you need to
5770 specify the target address as 'offset' parameter with the 'loads'
5773 Example: install the image to address 0x40100000 (which on the
5774 TQM8xxL is in the first Flash bank):
5776 => erase 40100000 401FFFFF
5782 ## Ready for S-Record download ...
5783 ~>examples/image.srec
5784 1 2 3 4 5 6 7 8 9 10 11 12 13 ...
5786 15989 15990 15991 15992
5787 [file transfer complete]
5789 ## Start Addr = 0x00000000
5792 You can check the success of the download using the 'iminfo' command;
5793 this includes a checksum verification so you can be sure no data
5794 corruption happened:
5798 ## Checking Image at 40100000 ...
5799 Image Name: 2.2.13 for initrd on TQM850L
5800 Image Type: PowerPC Linux Kernel Image (gzip compressed)
5801 Data Size: 335725 Bytes = 327 kB = 0 MB
5802 Load Address: 00000000
5803 Entry Point: 0000000c
5804 Verifying Checksum ... OK
5810 The "bootm" command is used to boot an application that is stored in
5811 memory (RAM or Flash). In case of a Linux kernel image, the contents
5812 of the "bootargs" environment variable is passed to the kernel as
5813 parameters. You can check and modify this variable using the
5814 "printenv" and "setenv" commands:
5817 => printenv bootargs
5818 bootargs=root=/dev/ram
5820 => setenv bootargs root=/dev/nfs rw nfsroot=10.0.0.2:/LinuxPPC nfsaddrs=10.0.0.99:10.0.0.2
5822 => printenv bootargs
5823 bootargs=root=/dev/nfs rw nfsroot=10.0.0.2:/LinuxPPC nfsaddrs=10.0.0.99:10.0.0.2
5826 ## Booting Linux kernel at 40020000 ...
5827 Image Name: 2.2.13 for NFS on TQM850L
5828 Image Type: PowerPC Linux Kernel Image (gzip compressed)
5829 Data Size: 381681 Bytes = 372 kB = 0 MB
5830 Load Address: 00000000
5831 Entry Point: 0000000c
5832 Verifying Checksum ... OK
5833 Uncompressing Kernel Image ... OK
5834 Linux version 2.2.13 (wd@denx.local.net) (gcc version 2.95.2 19991024 (release)) #1 Wed Jul 19 02:35:17 MEST 2000
5835 Boot arguments: root=/dev/nfs rw nfsroot=10.0.0.2:/LinuxPPC nfsaddrs=10.0.0.99:10.0.0.2
5836 time_init: decrementer frequency = 187500000/60
5837 Calibrating delay loop... 49.77 BogoMIPS
5838 Memory: 15208k available (700k kernel code, 444k data, 32k init) [c0000000,c1000000]
5841 If you want to boot a Linux kernel with initial RAM disk, you pass
5842 the memory addresses of both the kernel and the initrd image (PPBCOOT
5843 format!) to the "bootm" command:
5845 => imi 40100000 40200000
5847 ## Checking Image at 40100000 ...
5848 Image Name: 2.2.13 for initrd on TQM850L
5849 Image Type: PowerPC Linux Kernel Image (gzip compressed)
5850 Data Size: 335725 Bytes = 327 kB = 0 MB
5851 Load Address: 00000000
5852 Entry Point: 0000000c
5853 Verifying Checksum ... OK
5855 ## Checking Image at 40200000 ...
5856 Image Name: Simple Ramdisk Image
5857 Image Type: PowerPC Linux RAMDisk Image (gzip compressed)
5858 Data Size: 566530 Bytes = 553 kB = 0 MB
5859 Load Address: 00000000
5860 Entry Point: 00000000
5861 Verifying Checksum ... OK
5863 => bootm 40100000 40200000
5864 ## Booting Linux kernel at 40100000 ...
5865 Image Name: 2.2.13 for initrd on TQM850L
5866 Image Type: PowerPC Linux Kernel Image (gzip compressed)
5867 Data Size: 335725 Bytes = 327 kB = 0 MB
5868 Load Address: 00000000
5869 Entry Point: 0000000c
5870 Verifying Checksum ... OK
5871 Uncompressing Kernel Image ... OK
5872 ## Loading RAMDisk Image at 40200000 ...
5873 Image Name: Simple Ramdisk Image
5874 Image Type: PowerPC Linux RAMDisk Image (gzip compressed)
5875 Data Size: 566530 Bytes = 553 kB = 0 MB
5876 Load Address: 00000000
5877 Entry Point: 00000000
5878 Verifying Checksum ... OK
5879 Loading Ramdisk ... OK
5880 Linux version 2.2.13 (wd@denx.local.net) (gcc version 2.95.2 19991024 (release)) #1 Wed Jul 19 02:32:08 MEST 2000
5881 Boot arguments: root=/dev/ram
5882 time_init: decrementer frequency = 187500000/60
5883 Calibrating delay loop... 49.77 BogoMIPS
5885 RAMDISK: Compressed image found at block 0
5886 VFS: Mounted root (ext2 filesystem).
5890 Boot Linux and pass a flat device tree:
5893 First, U-Boot must be compiled with the appropriate defines. See the section
5894 titled "Linux Kernel Interface" above for a more in depth explanation. The
5895 following is an example of how to start a kernel and pass an updated
5901 oft=oftrees/mpc8540ads.dtb
5902 => tftp $oftaddr $oft
5903 Speed: 1000, full duplex
5905 TFTP from server 192.168.1.1; our IP address is 192.168.1.101
5906 Filename 'oftrees/mpc8540ads.dtb'.
5907 Load address: 0x300000
5910 Bytes transferred = 4106 (100a hex)
5911 => tftp $loadaddr $bootfile
5912 Speed: 1000, full duplex
5914 TFTP from server 192.168.1.1; our IP address is 192.168.1.2
5916 Load address: 0x200000
5917 Loading:############
5919 Bytes transferred = 1029407 (fb51f hex)
5924 => bootm $loadaddr - $oftaddr
5925 ## Booting image at 00200000 ...
5926 Image Name: Linux-2.6.17-dirty
5927 Image Type: PowerPC Linux Kernel Image (gzip compressed)
5928 Data Size: 1029343 Bytes = 1005.2 kB
5929 Load Address: 00000000
5930 Entry Point: 00000000
5931 Verifying Checksum ... OK
5932 Uncompressing Kernel Image ... OK
5933 Booting using flat device tree at 0x300000
5934 Using MPC85xx ADS machine description
5935 Memory CAM mapping: CAM0=256Mb, CAM1=256Mb, CAM2=0Mb residual: 0Mb
5939 More About U-Boot Image Types:
5940 ------------------------------
5942 U-Boot supports the following image types:
5944 "Standalone Programs" are directly runnable in the environment
5945 provided by U-Boot; it is expected that (if they behave
5946 well) you can continue to work in U-Boot after return from
5947 the Standalone Program.
5948 "OS Kernel Images" are usually images of some Embedded OS which
5949 will take over control completely. Usually these programs
5950 will install their own set of exception handlers, device
5951 drivers, set up the MMU, etc. - this means, that you cannot
5952 expect to re-enter U-Boot except by resetting the CPU.
5953 "RAMDisk Images" are more or less just data blocks, and their
5954 parameters (address, size) are passed to an OS kernel that is
5956 "Multi-File Images" contain several images, typically an OS
5957 (Linux) kernel image and one or more data images like
5958 RAMDisks. This construct is useful for instance when you want
5959 to boot over the network using BOOTP etc., where the boot
5960 server provides just a single image file, but you want to get
5961 for instance an OS kernel and a RAMDisk image.
5963 "Multi-File Images" start with a list of image sizes, each
5964 image size (in bytes) specified by an "uint32_t" in network
5965 byte order. This list is terminated by an "(uint32_t)0".
5966 Immediately after the terminating 0 follow the images, one by
5967 one, all aligned on "uint32_t" boundaries (size rounded up to
5968 a multiple of 4 bytes).
5970 "Firmware Images" are binary images containing firmware (like
5971 U-Boot or FPGA images) which usually will be programmed to
5974 "Script files" are command sequences that will be executed by
5975 U-Boot's command interpreter; this feature is especially
5976 useful when you configure U-Boot to use a real shell (hush)
5977 as command interpreter.
5979 Booting the Linux zImage:
5980 -------------------------
5982 On some platforms, it's possible to boot Linux zImage. This is done
5983 using the "bootz" command. The syntax of "bootz" command is the same
5984 as the syntax of "bootm" command.
5986 Note, defining the CONFIG_SUPPORT_RAW_INITRD allows user to supply
5987 kernel with raw initrd images. The syntax is slightly different, the
5988 address of the initrd must be augmented by it's size, in the following
5989 format: "<initrd addres>:<initrd size>".
5995 One of the features of U-Boot is that you can dynamically load and
5996 run "standalone" applications, which can use some resources of
5997 U-Boot like console I/O functions or interrupt services.
5999 Two simple examples are included with the sources:
6004 'examples/hello_world.c' contains a small "Hello World" Demo
6005 application; it is automatically compiled when you build U-Boot.
6006 It's configured to run at address 0x00040004, so you can play with it
6010 ## Ready for S-Record download ...
6011 ~>examples/hello_world.srec
6012 1 2 3 4 5 6 7 8 9 10 11 ...
6013 [file transfer complete]
6015 ## Start Addr = 0x00040004
6017 => go 40004 Hello World! This is a test.
6018 ## Starting application at 0x00040004 ...
6029 Hit any key to exit ...
6031 ## Application terminated, rc = 0x0
6033 Another example, which demonstrates how to register a CPM interrupt
6034 handler with the U-Boot code, can be found in 'examples/timer.c'.
6035 Here, a CPM timer is set up to generate an interrupt every second.
6036 The interrupt service routine is trivial, just printing a '.'
6037 character, but this is just a demo program. The application can be
6038 controlled by the following keys:
6040 ? - print current values og the CPM Timer registers
6041 b - enable interrupts and start timer
6042 e - stop timer and disable interrupts
6043 q - quit application
6046 ## Ready for S-Record download ...
6047 ~>examples/timer.srec
6048 1 2 3 4 5 6 7 8 9 10 11 ...
6049 [file transfer complete]
6051 ## Start Addr = 0x00040004
6054 ## Starting application at 0x00040004 ...
6057 tgcr @ 0xfff00980, tmr @ 0xfff00990, trr @ 0xfff00994, tcr @ 0xfff00998, tcn @ 0xfff0099c, ter @ 0xfff009b0
6060 [q, b, e, ?] Set interval 1000000 us
6063 [q, b, e, ?] ........
6064 tgcr=0x1, tmr=0xff1c, trr=0x3d09, tcr=0x0, tcn=0xef6, ter=0x0
6067 tgcr=0x1, tmr=0xff1c, trr=0x3d09, tcr=0x0, tcn=0x2ad4, ter=0x0
6070 tgcr=0x1, tmr=0xff1c, trr=0x3d09, tcr=0x0, tcn=0x1efc, ter=0x0
6073 tgcr=0x1, tmr=0xff1c, trr=0x3d09, tcr=0x0, tcn=0x169d, ter=0x0
6075 [q, b, e, ?] ...Stopping timer
6077 [q, b, e, ?] ## Application terminated, rc = 0x0
6083 Over time, many people have reported problems when trying to use the
6084 "minicom" terminal emulation program for serial download. I (wd)
6085 consider minicom to be broken, and recommend not to use it. Under
6086 Unix, I recommend to use C-Kermit for general purpose use (and
6087 especially for kermit binary protocol download ("loadb" command), and
6088 use "cu" for S-Record download ("loads" command). See
6089 http://www.denx.de/wiki/view/DULG/SystemSetup#Section_4.3.
6090 for help with kermit.
6093 Nevertheless, if you absolutely want to use it try adding this
6094 configuration to your "File transfer protocols" section:
6096 Name Program Name U/D FullScr IO-Red. Multi
6097 X kermit /usr/bin/kermit -i -l %l -s Y U Y N N
6098 Y kermit /usr/bin/kermit -i -l %l -r N D Y N N
6104 Starting at version 0.9.2, U-Boot supports NetBSD both as host
6105 (build U-Boot) and target system (boots NetBSD/mpc8xx).
6107 Building requires a cross environment; it is known to work on
6108 NetBSD/i386 with the cross-powerpc-netbsd-1.3 package (you will also
6109 need gmake since the Makefiles are not compatible with BSD make).
6110 Note that the cross-powerpc package does not install include files;
6111 attempting to build U-Boot will fail because <machine/ansi.h> is
6112 missing. This file has to be installed and patched manually:
6114 # cd /usr/pkg/cross/powerpc-netbsd/include
6116 # ln -s powerpc machine
6117 # cp /usr/src/sys/arch/powerpc/include/ansi.h powerpc/ansi.h
6118 # ${EDIT} powerpc/ansi.h ## must remove __va_list, _BSD_VA_LIST
6120 Native builds *don't* work due to incompatibilities between native
6121 and U-Boot include files.
6123 Booting assumes that (the first part of) the image booted is a
6124 stage-2 loader which in turn loads and then invokes the kernel
6125 proper. Loader sources will eventually appear in the NetBSD source
6126 tree (probably in sys/arc/mpc8xx/stand/u-boot_stage2/); in the
6127 meantime, see ftp://ftp.denx.de/pub/u-boot/ppcboot_stage2.tar.gz
6130 Implementation Internals:
6131 =========================
6133 The following is not intended to be a complete description of every
6134 implementation detail. However, it should help to understand the
6135 inner workings of U-Boot and make it easier to port it to custom
6139 Initial Stack, Global Data:
6140 ---------------------------
6142 The implementation of U-Boot is complicated by the fact that U-Boot
6143 starts running out of ROM (flash memory), usually without access to
6144 system RAM (because the memory controller is not initialized yet).
6145 This means that we don't have writable Data or BSS segments, and BSS
6146 is not initialized as zero. To be able to get a C environment working
6147 at all, we have to allocate at least a minimal stack. Implementation
6148 options for this are defined and restricted by the CPU used: Some CPU
6149 models provide on-chip memory (like the IMMR area on MPC8xx and
6150 MPC826x processors), on others (parts of) the data cache can be
6151 locked as (mis-) used as memory, etc.
6153 Chris Hallinan posted a good summary of these issues to the
6154 U-Boot mailing list:
6156 Subject: RE: [U-Boot-Users] RE: More On Memory Bank x (nothingness)?
6157 From: "Chris Hallinan" <clh@net1plus.com>
6158 Date: Mon, 10 Feb 2003 16:43:46 -0500 (22:43 MET)
6161 Correct me if I'm wrong, folks, but the way I understand it
6162 is this: Using DCACHE as initial RAM for Stack, etc, does not
6163 require any physical RAM backing up the cache. The cleverness
6164 is that the cache is being used as a temporary supply of
6165 necessary storage before the SDRAM controller is setup. It's
6166 beyond the scope of this list to explain the details, but you
6167 can see how this works by studying the cache architecture and
6168 operation in the architecture and processor-specific manuals.
6170 OCM is On Chip Memory, which I believe the 405GP has 4K. It
6171 is another option for the system designer to use as an
6172 initial stack/RAM area prior to SDRAM being available. Either
6173 option should work for you. Using CS 4 should be fine if your
6174 board designers haven't used it for something that would
6175 cause you grief during the initial boot! It is frequently not
6178 CONFIG_SYS_INIT_RAM_ADDR should be somewhere that won't interfere
6179 with your processor/board/system design. The default value
6180 you will find in any recent u-boot distribution in
6181 walnut.h should work for you. I'd set it to a value larger
6182 than your SDRAM module. If you have a 64MB SDRAM module, set
6183 it above 400_0000. Just make sure your board has no resources
6184 that are supposed to respond to that address! That code in
6185 start.S has been around a while and should work as is when
6186 you get the config right.
6191 It is essential to remember this, since it has some impact on the C
6192 code for the initialization procedures:
6194 * Initialized global data (data segment) is read-only. Do not attempt
6197 * Do not use any uninitialized global data (or implicitely initialized
6198 as zero data - BSS segment) at all - this is undefined, initiali-
6199 zation is performed later (when relocating to RAM).
6201 * Stack space is very limited. Avoid big data buffers or things like
6204 Having only the stack as writable memory limits means we cannot use
6205 normal global data to share information beween the code. But it
6206 turned out that the implementation of U-Boot can be greatly
6207 simplified by making a global data structure (gd_t) available to all
6208 functions. We could pass a pointer to this data as argument to _all_
6209 functions, but this would bloat the code. Instead we use a feature of
6210 the GCC compiler (Global Register Variables) to share the data: we
6211 place a pointer (gd) to the global data into a register which we
6212 reserve for this purpose.
6214 When choosing a register for such a purpose we are restricted by the
6215 relevant (E)ABI specifications for the current architecture, and by
6216 GCC's implementation.
6218 For PowerPC, the following registers have specific use:
6220 R2: reserved for system use
6221 R3-R4: parameter passing and return values
6222 R5-R10: parameter passing
6223 R13: small data area pointer
6227 (U-Boot also uses R12 as internal GOT pointer. r12
6228 is a volatile register so r12 needs to be reset when
6229 going back and forth between asm and C)
6231 ==> U-Boot will use R2 to hold a pointer to the global data
6233 Note: on PPC, we could use a static initializer (since the
6234 address of the global data structure is known at compile time),
6235 but it turned out that reserving a register results in somewhat
6236 smaller code - although the code savings are not that big (on
6237 average for all boards 752 bytes for the whole U-Boot image,
6238 624 text + 127 data).
6240 On Blackfin, the normal C ABI (except for P3) is followed as documented here:
6241 http://docs.blackfin.uclinux.org/doku.php?id=application_binary_interface
6243 ==> U-Boot will use P3 to hold a pointer to the global data
6245 On ARM, the following registers are used:
6247 R0: function argument word/integer result
6248 R1-R3: function argument word
6249 R9: platform specific
6250 R10: stack limit (used only if stack checking is enabled)
6251 R11: argument (frame) pointer
6252 R12: temporary workspace
6255 R15: program counter
6257 ==> U-Boot will use R9 to hold a pointer to the global data
6259 Note: on ARM, only R_ARM_RELATIVE relocations are supported.
6261 On Nios II, the ABI is documented here:
6262 http://www.altera.com/literature/hb/nios2/n2cpu_nii51016.pdf
6264 ==> U-Boot will use gp to hold a pointer to the global data
6266 Note: on Nios II, we give "-G0" option to gcc and don't use gp
6267 to access small data sections, so gp is free.
6269 On NDS32, the following registers are used:
6271 R0-R1: argument/return
6273 R15: temporary register for assembler
6274 R16: trampoline register
6275 R28: frame pointer (FP)
6276 R29: global pointer (GP)
6277 R30: link register (LP)
6278 R31: stack pointer (SP)
6279 PC: program counter (PC)
6281 ==> U-Boot will use R10 to hold a pointer to the global data
6283 NOTE: DECLARE_GLOBAL_DATA_PTR must be used with file-global scope,
6284 or current versions of GCC may "optimize" the code too much.
6289 U-Boot runs in system state and uses physical addresses, i.e. the
6290 MMU is not used either for address mapping nor for memory protection.
6292 The available memory is mapped to fixed addresses using the memory
6293 controller. In this process, a contiguous block is formed for each
6294 memory type (Flash, SDRAM, SRAM), even when it consists of several
6295 physical memory banks.
6297 U-Boot is installed in the first 128 kB of the first Flash bank (on
6298 TQM8xxL modules this is the range 0x40000000 ... 0x4001FFFF). After
6299 booting and sizing and initializing DRAM, the code relocates itself
6300 to the upper end of DRAM. Immediately below the U-Boot code some
6301 memory is reserved for use by malloc() [see CONFIG_SYS_MALLOC_LEN
6302 configuration setting]. Below that, a structure with global Board
6303 Info data is placed, followed by the stack (growing downward).
6305 Additionally, some exception handler code is copied to the low 8 kB
6306 of DRAM (0x00000000 ... 0x00001FFF).
6308 So a typical memory configuration with 16 MB of DRAM could look like
6311 0x0000 0000 Exception Vector code
6314 0x0000 2000 Free for Application Use
6320 0x00FB FF20 Monitor Stack (Growing downward)
6321 0x00FB FFAC Board Info Data and permanent copy of global data
6322 0x00FC 0000 Malloc Arena
6325 0x00FE 0000 RAM Copy of Monitor Code
6326 ... eventually: LCD or video framebuffer
6327 ... eventually: pRAM (Protected RAM - unchanged by reset)
6328 0x00FF FFFF [End of RAM]
6331 System Initialization:
6332 ----------------------
6334 In the reset configuration, U-Boot starts at the reset entry point
6335 (on most PowerPC systems at address 0x00000100). Because of the reset
6336 configuration for CS0# this is a mirror of the onboard Flash memory.
6337 To be able to re-map memory U-Boot then jumps to its link address.
6338 To be able to implement the initialization code in C, a (small!)
6339 initial stack is set up in the internal Dual Ported RAM (in case CPUs
6340 which provide such a feature like MPC8xx or MPC8260), or in a locked
6341 part of the data cache. After that, U-Boot initializes the CPU core,
6342 the caches and the SIU.
6344 Next, all (potentially) available memory banks are mapped using a
6345 preliminary mapping. For example, we put them on 512 MB boundaries
6346 (multiples of 0x20000000: SDRAM on 0x00000000 and 0x20000000, Flash
6347 on 0x40000000 and 0x60000000, SRAM on 0x80000000). Then UPM A is
6348 programmed for SDRAM access. Using the temporary configuration, a
6349 simple memory test is run that determines the size of the SDRAM
6352 When there is more than one SDRAM bank, and the banks are of
6353 different size, the largest is mapped first. For equal size, the first
6354 bank (CS2#) is mapped first. The first mapping is always for address
6355 0x00000000, with any additional banks following immediately to create
6356 contiguous memory starting from 0.
6358 Then, the monitor installs itself at the upper end of the SDRAM area
6359 and allocates memory for use by malloc() and for the global Board
6360 Info data; also, the exception vector code is copied to the low RAM
6361 pages, and the final stack is set up.
6363 Only after this relocation will you have a "normal" C environment;
6364 until that you are restricted in several ways, mostly because you are
6365 running from ROM, and because the code will have to be relocated to a
6369 U-Boot Porting Guide:
6370 ----------------------
6372 [Based on messages by Jerry Van Baren in the U-Boot-Users mailing
6376 int main(int argc, char *argv[])
6378 sighandler_t no_more_time;
6380 signal(SIGALRM, no_more_time);
6381 alarm(PROJECT_DEADLINE - toSec (3 * WEEK));
6383 if (available_money > available_manpower) {
6384 Pay consultant to port U-Boot;
6388 Download latest U-Boot source;
6390 Subscribe to u-boot mailing list;
6393 email("Hi, I am new to U-Boot, how do I get started?");
6396 Read the README file in the top level directory;
6397 Read http://www.denx.de/twiki/bin/view/DULG/Manual;
6398 Read applicable doc/*.README;
6399 Read the source, Luke;
6400 /* find . -name "*.[chS]" | xargs grep -i <keyword> */
6403 if (available_money > toLocalCurrency ($2500))
6406 Add a lot of aggravation and time;
6408 if (a similar board exists) { /* hopefully... */
6409 cp -a board/<similar> board/<myboard>
6410 cp include/configs/<similar>.h include/configs/<myboard>.h
6412 Create your own board support subdirectory;
6413 Create your own board include/configs/<myboard>.h file;
6415 Edit new board/<myboard> files
6416 Edit new include/configs/<myboard>.h
6421 Add / modify source code;
6425 email("Hi, I am having problems...");
6427 Send patch file to the U-Boot email list;
6428 if (reasonable critiques)
6429 Incorporate improvements from email list code review;
6431 Defend code as written;
6437 void no_more_time (int sig)
6446 All contributions to U-Boot should conform to the Linux kernel
6447 coding style; see the file "Documentation/CodingStyle" and the script
6448 "scripts/Lindent" in your Linux kernel source directory.
6450 Source files originating from a different project (for example the
6451 MTD subsystem) are generally exempt from these guidelines and are not
6452 reformated to ease subsequent migration to newer versions of those
6455 Please note that U-Boot is implemented in C (and to some small parts in
6456 Assembler); no C++ is used, so please do not use C++ style comments (//)
6459 Please also stick to the following formatting rules:
6460 - remove any trailing white space
6461 - use TAB characters for indentation and vertical alignment, not spaces
6462 - make sure NOT to use DOS '\r\n' line feeds
6463 - do not add more than 2 consecutive empty lines to source files
6464 - do not add trailing empty lines to source files
6466 Submissions which do not conform to the standards may be returned
6467 with a request to reformat the changes.
6473 Since the number of patches for U-Boot is growing, we need to
6474 establish some rules. Submissions which do not conform to these rules
6475 may be rejected, even when they contain important and valuable stuff.
6477 Please see http://www.denx.de/wiki/U-Boot/Patches for details.
6479 Patches shall be sent to the u-boot mailing list <u-boot@lists.denx.de>;
6480 see http://lists.denx.de/mailman/listinfo/u-boot
6482 When you send a patch, please include the following information with
6485 * For bug fixes: a description of the bug and how your patch fixes
6486 this bug. Please try to include a way of demonstrating that the
6487 patch actually fixes something.
6489 * For new features: a description of the feature and your
6492 * A CHANGELOG entry as plaintext (separate from the patch)
6494 * For major contributions, your entry to the CREDITS file
6496 * When you add support for a new board, don't forget to add a
6497 maintainer e-mail address to the boards.cfg file, too.
6499 * If your patch adds new configuration options, don't forget to
6500 document these in the README file.
6502 * The patch itself. If you are using git (which is *strongly*
6503 recommended) you can easily generate the patch using the
6504 "git format-patch". If you then use "git send-email" to send it to
6505 the U-Boot mailing list, you will avoid most of the common problems
6506 with some other mail clients.
6508 If you cannot use git, use "diff -purN OLD NEW". If your version of
6509 diff does not support these options, then get the latest version of
6512 The current directory when running this command shall be the parent
6513 directory of the U-Boot source tree (i. e. please make sure that
6514 your patch includes sufficient directory information for the
6517 We prefer patches as plain text. MIME attachments are discouraged,
6518 and compressed attachments must not be used.
6520 * If one logical set of modifications affects or creates several
6521 files, all these changes shall be submitted in a SINGLE patch file.
6523 * Changesets that contain different, unrelated modifications shall be
6524 submitted as SEPARATE patches, one patch per changeset.
6529 * Before sending the patch, run the MAKEALL script on your patched
6530 source tree and make sure that no errors or warnings are reported
6531 for any of the boards.
6533 * Keep your modifications to the necessary minimum: A patch
6534 containing several unrelated changes or arbitrary reformats will be
6535 returned with a request to re-formatting / split it.
6537 * If you modify existing code, make sure that your new code does not
6538 add to the memory footprint of the code ;-) Small is beautiful!
6539 When adding new features, these should compile conditionally only
6540 (using #ifdef), and the resulting code with the new feature
6541 disabled must not need more memory than the old code without your
6544 * Remember that there is a size limit of 100 kB per message on the
6545 u-boot mailing list. Bigger patches will be moderated. If they are
6546 reasonable and not too big, they will be acknowledged. But patches
6547 bigger than the size limit should be avoided.
projects / platform / kernel / u-boot.git / blob