2 # (C) Copyright 2000 - 2012
3 # Wolfgang Denk, DENX Software Engineering, wd@denx.de.
5 # See file CREDITS for list of people who contributed to this
8 # This program is free software; you can redistribute it and/or
9 # modify it under the terms of the GNU General Public License as
10 # published by the Free Software Foundation; either version 2 of
11 # the License, or (at your option) any later version.
13 # This program is distributed in the hope that it will be useful,
14 # but WITHOUT ANY WARRANTY; without even the implied warranty of
15 # MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the
16 # GNU General Public License for more details.
18 # You should have received a copy of the GNU General Public License
19 # along with this program; if not, write to the Free Software
20 # Foundation, Inc., 59 Temple Place, Suite 330, Boston,
27 This directory contains the source code for U-Boot, a boot loader for
28 Embedded boards based on PowerPC, ARM, MIPS and several other
29 processors, which can be installed in a boot ROM and used to
30 initialize and test the hardware or to download and run application
33 The development of U-Boot is closely related to Linux: some parts of
34 the source code originate in the Linux source tree, we have some
35 header files in common, and special provision has been made to
36 support booting of Linux images.
38 Some attention has been paid to make this software easily
39 configurable and extendable. For instance, all monitor commands are
40 implemented with the same call interface, so that it's very easy to
41 add new commands. Also, instead of permanently adding rarely used
42 code (for instance hardware test utilities) to the monitor, you can
43 load and run it dynamically.
49 In general, all boards for which a configuration option exists in the
50 Makefile have been tested to some extent and can be considered
51 "working". In fact, many of them are used in production systems.
53 In case of problems see the CHANGELOG and CREDITS files to find out
54 who contributed the specific port. The MAINTAINERS file lists board
57 Note: There is no CHANGELOG file in the actual U-Boot source tree;
58 it can be created dynamically from the Git log using:
66 In case you have questions about, problems with or contributions for
67 U-Boot you should send a message to the U-Boot mailing list at
68 <u-boot@lists.denx.de>. There is also an archive of previous traffic
69 on the mailing list - please search the archive before asking FAQ's.
70 Please see http://lists.denx.de/pipermail/u-boot and
71 http://dir.gmane.org/gmane.comp.boot-loaders.u-boot
74 Where to get source code:
75 =========================
77 The U-Boot source code is maintained in the git repository at
78 git://www.denx.de/git/u-boot.git ; you can browse it online at
79 http://www.denx.de/cgi-bin/gitweb.cgi?p=u-boot.git;a=summary
81 The "snapshot" links on this page allow you to download tarballs of
82 any version you might be interested in. Official releases are also
83 available for FTP download from the ftp://ftp.denx.de/pub/u-boot/
86 Pre-built (and tested) images are available from
87 ftp://ftp.denx.de/pub/u-boot/images/
93 - start from 8xxrom sources
94 - create PPCBoot project (http://sourceforge.net/projects/ppcboot)
96 - make it easier to add custom boards
97 - make it possible to add other [PowerPC] CPUs
98 - extend functions, especially:
99 * Provide extended interface to Linux boot loader
102 * PCMCIA / CompactFlash / ATA disk / SCSI ... boot
103 - create ARMBoot project (http://sourceforge.net/projects/armboot)
104 - add other CPU families (starting with ARM)
105 - create U-Boot project (http://sourceforge.net/projects/u-boot)
106 - current project page: see http://www.denx.de/wiki/U-Boot
112 The "official" name of this project is "Das U-Boot". The spelling
113 "U-Boot" shall be used in all written text (documentation, comments
114 in source files etc.). Example:
116 This is the README file for the U-Boot project.
118 File names etc. shall be based on the string "u-boot". Examples:
120 include/asm-ppc/u-boot.h
122 #include <asm/u-boot.h>
124 Variable names, preprocessor constants etc. shall be either based on
125 the string "u_boot" or on "U_BOOT". Example:
127 U_BOOT_VERSION u_boot_logo
128 IH_OS_U_BOOT u_boot_hush_start
134 Starting with the release in October 2008, the names of the releases
135 were changed from numerical release numbers without deeper meaning
136 into a time stamp based numbering. Regular releases are identified by
137 names consisting of the calendar year and month of the release date.
138 Additional fields (if present) indicate release candidates or bug fix
139 releases in "stable" maintenance trees.
142 U-Boot v2009.11 - Release November 2009
143 U-Boot v2009.11.1 - Release 1 in version November 2009 stable tree
144 U-Boot v2010.09-rc1 - Release candiate 1 for September 2010 release
150 /arch Architecture specific files
151 /arm Files generic to ARM architecture
152 /cpu CPU specific files
153 /arm720t Files specific to ARM 720 CPUs
154 /arm920t Files specific to ARM 920 CPUs
155 /at91 Files specific to Atmel AT91RM9200 CPU
156 /imx Files specific to Freescale MC9328 i.MX CPUs
157 /s3c24x0 Files specific to Samsung S3C24X0 CPUs
158 /arm925t Files specific to ARM 925 CPUs
159 /arm926ejs Files specific to ARM 926 CPUs
160 /arm1136 Files specific to ARM 1136 CPUs
161 /ixp Files specific to Intel XScale IXP CPUs
162 /pxa Files specific to Intel XScale PXA CPUs
163 /s3c44b0 Files specific to Samsung S3C44B0 CPUs
164 /sa1100 Files specific to Intel StrongARM SA1100 CPUs
165 /lib Architecture specific library files
166 /avr32 Files generic to AVR32 architecture
167 /cpu CPU specific files
168 /lib Architecture specific library files
169 /blackfin Files generic to Analog Devices Blackfin architecture
170 /cpu CPU specific files
171 /lib Architecture specific library files
172 /x86 Files generic to x86 architecture
173 /cpu CPU specific files
174 /lib Architecture specific library files
175 /m68k Files generic to m68k architecture
176 /cpu CPU specific files
177 /mcf52x2 Files specific to Freescale ColdFire MCF52x2 CPUs
178 /mcf5227x Files specific to Freescale ColdFire MCF5227x CPUs
179 /mcf532x Files specific to Freescale ColdFire MCF5329 CPUs
180 /mcf5445x Files specific to Freescale ColdFire MCF5445x CPUs
181 /mcf547x_8x Files specific to Freescale ColdFire MCF547x_8x CPUs
182 /lib Architecture specific library files
183 /microblaze Files generic to microblaze architecture
184 /cpu CPU specific files
185 /lib Architecture specific library files
186 /mips Files generic to MIPS architecture
187 /cpu CPU specific files
188 /mips32 Files specific to MIPS32 CPUs
189 /xburst Files specific to Ingenic XBurst CPUs
190 /lib Architecture specific library files
191 /nds32 Files generic to NDS32 architecture
192 /cpu CPU specific files
193 /n1213 Files specific to Andes Technology N1213 CPUs
194 /lib Architecture specific library files
195 /nios2 Files generic to Altera NIOS2 architecture
196 /cpu CPU specific files
197 /lib Architecture specific library files
198 /powerpc Files generic to PowerPC architecture
199 /cpu CPU specific files
200 /74xx_7xx Files specific to Freescale MPC74xx and 7xx CPUs
201 /mpc5xx Files specific to Freescale MPC5xx CPUs
202 /mpc5xxx Files specific to Freescale MPC5xxx CPUs
203 /mpc8xx Files specific to Freescale MPC8xx CPUs
204 /mpc8220 Files specific to Freescale MPC8220 CPUs
205 /mpc824x Files specific to Freescale MPC824x CPUs
206 /mpc8260 Files specific to Freescale MPC8260 CPUs
207 /mpc85xx Files specific to Freescale MPC85xx CPUs
208 /ppc4xx Files specific to AMCC PowerPC 4xx CPUs
209 /lib Architecture specific library files
210 /sh Files generic to SH architecture
211 /cpu CPU specific files
212 /sh2 Files specific to sh2 CPUs
213 /sh3 Files specific to sh3 CPUs
214 /sh4 Files specific to sh4 CPUs
215 /lib Architecture specific library files
216 /sparc Files generic to SPARC architecture
217 /cpu CPU specific files
218 /leon2 Files specific to Gaisler LEON2 SPARC CPU
219 /leon3 Files specific to Gaisler LEON3 SPARC CPU
220 /lib Architecture specific library files
221 /api Machine/arch independent API for external apps
222 /board Board dependent files
223 /common Misc architecture independent functions
224 /disk Code for disk drive partition handling
225 /doc Documentation (don't expect too much)
226 /drivers Commonly used device drivers
227 /examples Example code for standalone applications, etc.
228 /fs Filesystem code (cramfs, ext2, jffs2, etc.)
229 /include Header Files
230 /lib Files generic to all architectures
231 /libfdt Library files to support flattened device trees
232 /lzma Library files to support LZMA decompression
233 /lzo Library files to support LZO decompression
235 /post Power On Self Test
236 /rtc Real Time Clock drivers
237 /tools Tools to build S-Record or U-Boot images, etc.
239 Software Configuration:
240 =======================
242 Configuration is usually done using C preprocessor defines; the
243 rationale behind that is to avoid dead code whenever possible.
245 There are two classes of configuration variables:
247 * Configuration _OPTIONS_:
248 These are selectable by the user and have names beginning with
251 * Configuration _SETTINGS_:
252 These depend on the hardware etc. and should not be meddled with if
253 you don't know what you're doing; they have names beginning with
256 Later we will add a configuration tool - probably similar to or even
257 identical to what's used for the Linux kernel. Right now, we have to
258 do the configuration by hand, which means creating some symbolic
259 links and editing some configuration files. We use the TQM8xxL boards
263 Selection of Processor Architecture and Board Type:
264 ---------------------------------------------------
266 For all supported boards there are ready-to-use default
267 configurations available; just type "make <board_name>_config".
269 Example: For a TQM823L module type:
274 For the Cogent platform, you need to specify the CPU type as well;
275 e.g. "make cogent_mpc8xx_config". And also configure the cogent
276 directory according to the instructions in cogent/README.
279 Configuration Options:
280 ----------------------
282 Configuration depends on the combination of board and CPU type; all
283 such information is kept in a configuration file
284 "include/configs/<board_name>.h".
286 Example: For a TQM823L module, all configuration settings are in
287 "include/configs/TQM823L.h".
290 Many of the options are named exactly as the corresponding Linux
291 kernel configuration options. The intention is to make it easier to
292 build a config tool - later.
295 The following options need to be configured:
297 - CPU Type: Define exactly one, e.g. CONFIG_MPC85XX.
299 - Board Type: Define exactly one, e.g. CONFIG_MPC8540ADS.
301 - CPU Daughterboard Type: (if CONFIG_ATSTK1000 is defined)
302 Define exactly one, e.g. CONFIG_ATSTK1002
304 - CPU Module Type: (if CONFIG_COGENT is defined)
305 Define exactly one of
307 --- FIXME --- not tested yet:
308 CONFIG_CMA286_60, CONFIG_CMA286_21, CONFIG_CMA286_60P,
309 CONFIG_CMA287_23, CONFIG_CMA287_50
311 - Motherboard Type: (if CONFIG_COGENT is defined)
312 Define exactly one of
313 CONFIG_CMA101, CONFIG_CMA102
315 - Motherboard I/O Modules: (if CONFIG_COGENT is defined)
316 Define one or more of
319 - Motherboard Options: (if CONFIG_CMA101 or CONFIG_CMA102 are defined)
320 Define one or more of
321 CONFIG_LCD_HEARTBEAT - update a character position on
322 the LCD display every second with
325 - Board flavour: (if CONFIG_MPC8260ADS is defined)
328 CONFIG_SYS_8260ADS - original MPC8260ADS
329 CONFIG_SYS_8266ADS - MPC8266ADS
330 CONFIG_SYS_PQ2FADS - PQ2FADS-ZU or PQ2FADS-VR
331 CONFIG_SYS_8272ADS - MPC8272ADS
333 - Marvell Family Member
334 CONFIG_SYS_MVFS - define it if you want to enable
335 multiple fs option at one time
336 for marvell soc family
338 - MPC824X Family Member (if CONFIG_MPC824X is defined)
339 Define exactly one of
340 CONFIG_MPC8240, CONFIG_MPC8245
342 - 8xx CPU Options: (if using an MPC8xx CPU)
343 CONFIG_8xx_GCLK_FREQ - deprecated: CPU clock if
344 get_gclk_freq() cannot work
345 e.g. if there is no 32KHz
346 reference PIT/RTC clock
347 CONFIG_8xx_OSCLK - PLL input clock (either EXTCLK
350 - 859/866/885 CPU options: (if using a MPC859 or MPC866 or MPC885 CPU):
351 CONFIG_SYS_8xx_CPUCLK_MIN
352 CONFIG_SYS_8xx_CPUCLK_MAX
353 CONFIG_8xx_CPUCLK_DEFAULT
354 See doc/README.MPC866
356 CONFIG_SYS_MEASURE_CPUCLK
358 Define this to measure the actual CPU clock instead
359 of relying on the correctness of the configured
360 values. Mostly useful for board bringup to make sure
361 the PLL is locked at the intended frequency. Note
362 that this requires a (stable) reference clock (32 kHz
363 RTC clock or CONFIG_SYS_8XX_XIN)
365 CONFIG_SYS_DELAYED_ICACHE
367 Define this option if you want to enable the
368 ICache only when Code runs from RAM.
373 Specifies that the core is a 64-bit PowerPC implementation (implements
374 the "64" category of the Power ISA). This is necessary for ePAPR
375 compliance, among other possible reasons.
377 CONFIG_SYS_FSL_TBCLK_DIV
379 Defines the core time base clock divider ratio compared to the
380 system clock. On most PQ3 devices this is 8, on newer QorIQ
381 devices it can be 16 or 32. The ratio varies from SoC to Soc.
383 CONFIG_SYS_FSL_PCIE_COMPAT
385 Defines the string to utilize when trying to match PCIe device
386 tree nodes for the given platform.
388 CONFIG_SYS_PPC_E500_DEBUG_TLB
390 Enables a temporary TLB entry to be used during boot to work
391 around limitations in e500v1 and e500v2 external debugger
392 support. This reduces the portions of the boot code where
393 breakpoints and single stepping do not work. The value of this
394 symbol should be set to the TLB1 entry to be used for this
397 CONFIG_SYS_FSL_ERRATUM_A004510
399 Enables a workaround for erratum A004510. If set,
400 then CONFIG_SYS_FSL_ERRATUM_A004510_SVR_REV and
401 CONFIG_SYS_FSL_CORENET_SNOOPVEC_COREONLY must be set.
403 CONFIG_SYS_FSL_ERRATUM_A004510_SVR_REV
404 CONFIG_SYS_FSL_ERRATUM_A004510_SVR_REV2 (optional)
406 Defines one or two SoC revisions (low 8 bits of SVR)
407 for which the A004510 workaround should be applied.
409 The rest of SVR is either not relevant to the decision
410 of whether the erratum is present (e.g. p2040 versus
411 p2041) or is implied by the build target, which controls
412 whether CONFIG_SYS_FSL_ERRATUM_A004510 is set.
414 See Freescale App Note 4493 for more information about
417 CONFIG_SYS_FSL_CORENET_SNOOPVEC_COREONLY
419 This is the value to write into CCSR offset 0x18600
420 according to the A004510 workaround.
422 - Generic CPU options:
423 CONFIG_SYS_BIG_ENDIAN, CONFIG_SYS_LITTLE_ENDIAN
425 Defines the endianess of the CPU. Implementation of those
426 values is arch specific.
428 - Intel Monahans options:
429 CONFIG_SYS_MONAHANS_RUN_MODE_OSC_RATIO
431 Defines the Monahans run mode to oscillator
432 ratio. Valid values are 8, 16, 24, 31. The core
433 frequency is this value multiplied by 13 MHz.
435 CONFIG_SYS_MONAHANS_TURBO_RUN_MODE_RATIO
437 Defines the Monahans turbo mode to oscillator
438 ratio. Valid values are 1 (default if undefined) and
439 2. The core frequency as calculated above is multiplied
443 CONFIG_SYS_INIT_SP_OFFSET
445 Offset relative to CONFIG_SYS_SDRAM_BASE for initial stack
446 pointer. This is needed for the temporary stack before
449 CONFIG_SYS_MIPS_CACHE_MODE
451 Cache operation mode for the MIPS CPU.
452 See also arch/mips/include/asm/mipsregs.h.
454 CONF_CM_CACHABLE_NO_WA
457 CONF_CM_CACHABLE_NONCOHERENT
461 CONF_CM_CACHABLE_ACCELERATED
463 CONFIG_SYS_XWAY_EBU_BOOTCFG
465 Special option for Lantiq XWAY SoCs for booting from NOR flash.
466 See also arch/mips/cpu/mips32/start.S.
468 CONFIG_XWAY_SWAP_BYTES
470 Enable compilation of tools/xway-swap-bytes needed for Lantiq
471 XWAY SoCs for booting from NOR flash. The U-Boot image needs to
472 be swapped if a flash programmer is used.
475 CONFIG_SYS_EXCEPTION_VECTORS_HIGH
477 Select high exception vectors of the ARM core, e.g., do not
478 clear the V bit of the c1 register of CP15.
480 CONFIG_SYS_THUMB_BUILD
482 Use this flag to build U-Boot using the Thumb instruction
483 set for ARM architectures. Thumb instruction set provides
484 better code density. For ARM architectures that support
485 Thumb2 this flag will result in Thumb2 code generated by
488 CONFIG_ARM_ERRATA_716044
489 CONFIG_ARM_ERRATA_742230
490 CONFIG_ARM_ERRATA_743622
491 CONFIG_ARM_ERRATA_751472
493 If set, the workarounds for these ARM errata are applied early
494 during U-Boot startup. Note that these options force the
495 workarounds to be applied; no CPU-type/version detection
496 exists, unlike the similar options in the Linux kernel. Do not
497 set these options unless they apply!
502 The frequency of the timer returned by get_timer().
503 get_timer() must operate in milliseconds and this CONFIG
504 option must be set to 1000.
506 - Linux Kernel Interface:
509 U-Boot stores all clock information in Hz
510 internally. For binary compatibility with older Linux
511 kernels (which expect the clocks passed in the
512 bd_info data to be in MHz) the environment variable
513 "clocks_in_mhz" can be defined so that U-Boot
514 converts clock data to MHZ before passing it to the
516 When CONFIG_CLOCKS_IN_MHZ is defined, a definition of
517 "clocks_in_mhz=1" is automatically included in the
520 CONFIG_MEMSIZE_IN_BYTES [relevant for MIPS only]
522 When transferring memsize parameter to linux, some versions
523 expect it to be in bytes, others in MB.
524 Define CONFIG_MEMSIZE_IN_BYTES to make it in bytes.
528 New kernel versions are expecting firmware settings to be
529 passed using flattened device trees (based on open firmware
533 * New libfdt-based support
534 * Adds the "fdt" command
535 * The bootm command automatically updates the fdt
537 OF_CPU - The proper name of the cpus node (only required for
538 MPC512X and MPC5xxx based boards).
539 OF_SOC - The proper name of the soc node (only required for
540 MPC512X and MPC5xxx based boards).
541 OF_TBCLK - The timebase frequency.
542 OF_STDOUT_PATH - The path to the console device
544 boards with QUICC Engines require OF_QE to set UCC MAC
547 CONFIG_OF_BOARD_SETUP
549 Board code has addition modification that it wants to make
550 to the flat device tree before handing it off to the kernel
554 This define fills in the correct boot CPU in the boot
555 param header, the default value is zero if undefined.
559 U-Boot can detect if an IDE device is present or not.
560 If not, and this new config option is activated, U-Boot
561 removes the ATA node from the DTS before booting Linux,
562 so the Linux IDE driver does not probe the device and
563 crash. This is needed for buggy hardware (uc101) where
564 no pull down resistor is connected to the signal IDE5V_DD7.
566 CONFIG_MACH_TYPE [relevant for ARM only][mandatory]
568 This setting is mandatory for all boards that have only one
569 machine type and must be used to specify the machine type
570 number as it appears in the ARM machine registry
571 (see http://www.arm.linux.org.uk/developer/machines/).
572 Only boards that have multiple machine types supported
573 in a single configuration file and the machine type is
574 runtime discoverable, do not have to use this setting.
576 - vxWorks boot parameters:
578 bootvx constructs a valid bootline using the following
579 environments variables: bootfile, ipaddr, serverip, hostname.
580 It loads the vxWorks image pointed bootfile.
582 CONFIG_SYS_VXWORKS_BOOT_DEVICE - The vxworks device name
583 CONFIG_SYS_VXWORKS_MAC_PTR - Ethernet 6 byte MA -address
584 CONFIG_SYS_VXWORKS_SERVERNAME - Name of the server
585 CONFIG_SYS_VXWORKS_BOOT_ADDR - Address of boot parameters
587 CONFIG_SYS_VXWORKS_ADD_PARAMS
589 Add it at the end of the bootline. E.g "u=username pw=secret"
591 Note: If a "bootargs" environment is defined, it will overwride
592 the defaults discussed just above.
594 - Cache Configuration:
595 CONFIG_SYS_ICACHE_OFF - Do not enable instruction cache in U-Boot
596 CONFIG_SYS_DCACHE_OFF - Do not enable data cache in U-Boot
597 CONFIG_SYS_L2CACHE_OFF- Do not enable L2 cache in U-Boot
599 - Cache Configuration for ARM:
600 CONFIG_SYS_L2_PL310 - Enable support for ARM PL310 L2 cache
602 CONFIG_SYS_PL310_BASE - Physical base address of PL310
603 controller register space
608 Define this if you want support for Amba PrimeCell PL010 UARTs.
612 Define this if you want support for Amba PrimeCell PL011 UARTs.
616 If you have Amba PrimeCell PL011 UARTs, set this variable to
617 the clock speed of the UARTs.
621 If you have Amba PrimeCell PL010 or PL011 UARTs on your board,
622 define this to a list of base addresses for each (supported)
623 port. See e.g. include/configs/versatile.h
625 CONFIG_PL011_SERIAL_RLCR
627 Some vendor versions of PL011 serial ports (e.g. ST-Ericsson U8500)
628 have separate receive and transmit line control registers. Set
629 this variable to initialize the extra register.
631 CONFIG_PL011_SERIAL_FLUSH_ON_INIT
633 On some platforms (e.g. U8500) U-Boot is loaded by a second stage
634 boot loader that has already initialized the UART. Define this
635 variable to flush the UART at init time.
637 CONFIG_SYS_NS16550_BROKEN_TEMT
639 16550 UART set the Transmitter Empty (TEMT) Bit when all output
640 has finished and the transmitter is totally empty. U-Boot waits
641 for this bit to be set to initialize the serial console. On some
642 broken platforms this bit is not set in SPL making U-Boot to
643 hang while waiting for TEMT. Define this option to avoid it.
647 Depending on board, define exactly one serial port
648 (like CONFIG_8xx_CONS_SMC1, CONFIG_8xx_CONS_SMC2,
649 CONFIG_8xx_CONS_SCC1, ...), or switch off the serial
650 console by defining CONFIG_8xx_CONS_NONE
652 Note: if CONFIG_8xx_CONS_NONE is defined, the serial
653 port routines must be defined elsewhere
654 (i.e. serial_init(), serial_getc(), ...)
657 Enables console device for a color framebuffer. Needs following
658 defines (cf. smiLynxEM, i8042)
659 VIDEO_FB_LITTLE_ENDIAN graphic memory organisation
661 VIDEO_HW_RECTFILL graphic chip supports
664 VIDEO_HW_BITBLT graphic chip supports
665 bit-blit (cf. smiLynxEM)
666 VIDEO_VISIBLE_COLS visible pixel columns
668 VIDEO_VISIBLE_ROWS visible pixel rows
669 VIDEO_PIXEL_SIZE bytes per pixel
670 VIDEO_DATA_FORMAT graphic data format
671 (0-5, cf. cfb_console.c)
672 VIDEO_FB_ADRS framebuffer address
673 VIDEO_KBD_INIT_FCT keyboard int fct
674 (i.e. i8042_kbd_init())
675 VIDEO_TSTC_FCT test char fct
677 VIDEO_GETC_FCT get char fct
679 CONFIG_CONSOLE_CURSOR cursor drawing on/off
680 (requires blink timer
682 CONFIG_SYS_CONSOLE_BLINK_COUNT blink interval (cf. i8042.c)
683 CONFIG_CONSOLE_TIME display time/date info in
685 (requires CONFIG_CMD_DATE)
686 CONFIG_VIDEO_LOGO display Linux logo in
688 CONFIG_VIDEO_BMP_LOGO use bmp_logo.h instead of
689 linux_logo.h for logo.
690 Requires CONFIG_VIDEO_LOGO
691 CONFIG_CONSOLE_EXTRA_INFO
692 additional board info beside
695 When CONFIG_CFB_CONSOLE_ANSI is defined, console will support
696 a limited number of ANSI escape sequences (cursor control,
697 erase functions and limited graphics rendition control).
699 When CONFIG_CFB_CONSOLE is defined, video console is
700 default i/o. Serial console can be forced with
701 environment 'console=serial'.
703 When CONFIG_SILENT_CONSOLE is defined, all console
704 messages (by U-Boot and Linux!) can be silenced with
705 the "silent" environment variable. See
706 doc/README.silent for more information.
709 CONFIG_BAUDRATE - in bps
710 Select one of the baudrates listed in
711 CONFIG_SYS_BAUDRATE_TABLE, see below.
712 CONFIG_SYS_BRGCLK_PRESCALE, baudrate prescale
714 - Console Rx buffer length
715 With CONFIG_SYS_SMC_RXBUFLEN it is possible to define
716 the maximum receive buffer length for the SMC.
717 This option is actual only for 82xx and 8xx possible.
718 If using CONFIG_SYS_SMC_RXBUFLEN also CONFIG_SYS_MAXIDLE
719 must be defined, to setup the maximum idle timeout for
722 - Pre-Console Buffer:
723 Prior to the console being initialised (i.e. serial UART
724 initialised etc) all console output is silently discarded.
725 Defining CONFIG_PRE_CONSOLE_BUFFER will cause U-Boot to
726 buffer any console messages prior to the console being
727 initialised to a buffer of size CONFIG_PRE_CON_BUF_SZ
728 bytes located at CONFIG_PRE_CON_BUF_ADDR. The buffer is
729 a circular buffer, so if more than CONFIG_PRE_CON_BUF_SZ
730 bytes are output before the console is initialised, the
731 earlier bytes are discarded.
733 'Sane' compilers will generate smaller code if
734 CONFIG_PRE_CON_BUF_SZ is a power of 2
736 - Safe printf() functions
737 Define CONFIG_SYS_VSNPRINTF to compile in safe versions of
738 the printf() functions. These are defined in
739 include/vsprintf.h and include snprintf(), vsnprintf() and
740 so on. Code size increase is approximately 300-500 bytes.
741 If this option is not given then these functions will
742 silently discard their buffer size argument - this means
743 you are not getting any overflow checking in this case.
745 - Boot Delay: CONFIG_BOOTDELAY - in seconds
746 Delay before automatically booting the default image;
747 set to -1 to disable autoboot.
748 set to -2 to autoboot with no delay and not check for abort
749 (even when CONFIG_ZERO_BOOTDELAY_CHECK is defined).
751 See doc/README.autoboot for these options that
752 work with CONFIG_BOOTDELAY. None are required.
753 CONFIG_BOOT_RETRY_TIME
754 CONFIG_BOOT_RETRY_MIN
755 CONFIG_AUTOBOOT_KEYED
756 CONFIG_AUTOBOOT_PROMPT
757 CONFIG_AUTOBOOT_DELAY_STR
758 CONFIG_AUTOBOOT_STOP_STR
759 CONFIG_AUTOBOOT_DELAY_STR2
760 CONFIG_AUTOBOOT_STOP_STR2
761 CONFIG_ZERO_BOOTDELAY_CHECK
762 CONFIG_RESET_TO_RETRY
766 Only needed when CONFIG_BOOTDELAY is enabled;
767 define a command string that is automatically executed
768 when no character is read on the console interface
769 within "Boot Delay" after reset.
772 This can be used to pass arguments to the bootm
773 command. The value of CONFIG_BOOTARGS goes into the
774 environment value "bootargs".
776 CONFIG_RAMBOOT and CONFIG_NFSBOOT
777 The value of these goes into the environment as
778 "ramboot" and "nfsboot" respectively, and can be used
779 as a convenience, when switching between booting from
785 When this option is #defined, the existence of the
786 environment variable "preboot" will be checked
787 immediately before starting the CONFIG_BOOTDELAY
788 countdown and/or running the auto-boot command resp.
789 entering interactive mode.
791 This feature is especially useful when "preboot" is
792 automatically generated or modified. For an example
793 see the LWMON board specific code: here "preboot" is
794 modified when the user holds down a certain
795 combination of keys on the (special) keyboard when
798 - Serial Download Echo Mode:
800 If defined to 1, all characters received during a
801 serial download (using the "loads" command) are
802 echoed back. This might be needed by some terminal
803 emulations (like "cu"), but may as well just take
804 time on others. This setting #define's the initial
805 value of the "loads_echo" environment variable.
807 - Kgdb Serial Baudrate: (if CONFIG_CMD_KGDB is defined)
809 Select one of the baudrates listed in
810 CONFIG_SYS_BAUDRATE_TABLE, see below.
813 Monitor commands can be included or excluded
814 from the build by using the #include files
815 <config_cmd_all.h> and #undef'ing unwanted
816 commands, or using <config_cmd_default.h>
817 and augmenting with additional #define's
820 The default command configuration includes all commands
821 except those marked below with a "*".
823 CONFIG_CMD_ASKENV * ask for env variable
824 CONFIG_CMD_BDI bdinfo
825 CONFIG_CMD_BEDBUG * Include BedBug Debugger
826 CONFIG_CMD_BMP * BMP support
827 CONFIG_CMD_BSP * Board specific commands
828 CONFIG_CMD_BOOTD bootd
829 CONFIG_CMD_CACHE * icache, dcache
830 CONFIG_CMD_CONSOLE coninfo
831 CONFIG_CMD_CRC32 * crc32
832 CONFIG_CMD_DATE * support for RTC, date/time...
833 CONFIG_CMD_DHCP * DHCP support
834 CONFIG_CMD_DIAG * Diagnostics
835 CONFIG_CMD_DS4510 * ds4510 I2C gpio commands
836 CONFIG_CMD_DS4510_INFO * ds4510 I2C info command
837 CONFIG_CMD_DS4510_MEM * ds4510 I2C eeprom/sram commansd
838 CONFIG_CMD_DS4510_RST * ds4510 I2C rst command
839 CONFIG_CMD_DTT * Digital Therm and Thermostat
840 CONFIG_CMD_ECHO echo arguments
841 CONFIG_CMD_EDITENV edit env variable
842 CONFIG_CMD_EEPROM * EEPROM read/write support
843 CONFIG_CMD_ELF * bootelf, bootvx
844 CONFIG_CMD_ENV_CALLBACK * display details about env callbacks
845 CONFIG_CMD_ENV_FLAGS * display details about env flags
846 CONFIG_CMD_EXPORTENV * export the environment
847 CONFIG_CMD_EXT2 * ext2 command support
848 CONFIG_CMD_EXT4 * ext4 command support
849 CONFIG_CMD_SAVEENV saveenv
850 CONFIG_CMD_FDC * Floppy Disk Support
851 CONFIG_CMD_FAT * FAT command support
852 CONFIG_CMD_FDOS * Dos diskette Support
853 CONFIG_CMD_FLASH flinfo, erase, protect
854 CONFIG_CMD_FPGA FPGA device initialization support
855 CONFIG_CMD_GETTIME * Get time since boot
856 CONFIG_CMD_GO * the 'go' command (exec code)
857 CONFIG_CMD_GREPENV * search environment
858 CONFIG_CMD_HASH * calculate hash / digest
859 CONFIG_CMD_HWFLOW * RTS/CTS hw flow control
860 CONFIG_CMD_I2C * I2C serial bus support
861 CONFIG_CMD_IDE * IDE harddisk support
862 CONFIG_CMD_IMI iminfo
863 CONFIG_CMD_IMLS List all images found in NOR flash
864 CONFIG_CMD_IMLS_NAND List all images found in NAND flash
865 CONFIG_CMD_IMMAP * IMMR dump support
866 CONFIG_CMD_IMPORTENV * import an environment
867 CONFIG_CMD_INI * import data from an ini file into the env
868 CONFIG_CMD_IRQ * irqinfo
869 CONFIG_CMD_ITEST Integer/string test of 2 values
870 CONFIG_CMD_JFFS2 * JFFS2 Support
871 CONFIG_CMD_KGDB * kgdb
872 CONFIG_CMD_LDRINFO ldrinfo (display Blackfin loader)
873 CONFIG_CMD_LINK_LOCAL * link-local IP address auto-configuration
875 CONFIG_CMD_LOADB loadb
876 CONFIG_CMD_LOADS loads
877 CONFIG_CMD_MD5SUM print md5 message digest
878 (requires CONFIG_CMD_MEMORY and CONFIG_MD5)
879 CONFIG_CMD_MEMINFO * Display detailed memory information
880 CONFIG_CMD_MEMORY md, mm, nm, mw, cp, cmp, crc, base,
882 CONFIG_CMD_MEMTEST mtest
883 CONFIG_CMD_MISC Misc functions like sleep etc
884 CONFIG_CMD_MMC * MMC memory mapped support
885 CONFIG_CMD_MII * MII utility commands
886 CONFIG_CMD_MTDPARTS * MTD partition support
887 CONFIG_CMD_NAND * NAND support
888 CONFIG_CMD_NET bootp, tftpboot, rarpboot
889 CONFIG_CMD_PCA953X * PCA953x I2C gpio commands
890 CONFIG_CMD_PCA953X_INFO * PCA953x I2C gpio info command
891 CONFIG_CMD_PCI * pciinfo
892 CONFIG_CMD_PCMCIA * PCMCIA support
893 CONFIG_CMD_PING * send ICMP ECHO_REQUEST to network
895 CONFIG_CMD_PORTIO * Port I/O
896 CONFIG_CMD_READ * Read raw data from partition
897 CONFIG_CMD_REGINFO * Register dump
898 CONFIG_CMD_RUN run command in env variable
899 CONFIG_CMD_SANDBOX * sb command to access sandbox features
900 CONFIG_CMD_SAVES * save S record dump
901 CONFIG_CMD_SCSI * SCSI Support
902 CONFIG_CMD_SDRAM * print SDRAM configuration information
903 (requires CONFIG_CMD_I2C)
904 CONFIG_CMD_SETGETDCR Support for DCR Register access
906 CONFIG_CMD_SF * Read/write/erase SPI NOR flash
907 CONFIG_CMD_SHA1SUM print sha1 memory digest
908 (requires CONFIG_CMD_MEMORY)
909 CONFIG_CMD_SOURCE "source" command Support
910 CONFIG_CMD_SPI * SPI serial bus support
911 CONFIG_CMD_TFTPSRV * TFTP transfer in server mode
912 CONFIG_CMD_TFTPPUT * TFTP put command (upload)
913 CONFIG_CMD_TIME * run command and report execution time (ARM specific)
914 CONFIG_CMD_TIMER * access to the system tick timer
915 CONFIG_CMD_USB * USB support
916 CONFIG_CMD_CDP * Cisco Discover Protocol support
917 CONFIG_CMD_MFSL * Microblaze FSL support
920 EXAMPLE: If you want all functions except of network
921 support you can write:
923 #include "config_cmd_all.h"
924 #undef CONFIG_CMD_NET
927 fdt (flattened device tree) command: CONFIG_OF_LIBFDT
929 Note: Don't enable the "icache" and "dcache" commands
930 (configuration option CONFIG_CMD_CACHE) unless you know
931 what you (and your U-Boot users) are doing. Data
932 cache cannot be enabled on systems like the 8xx or
933 8260 (where accesses to the IMMR region must be
934 uncached), and it cannot be disabled on all other
935 systems where we (mis-) use the data cache to hold an
936 initial stack and some data.
939 XXX - this list needs to get updated!
943 If this variable is defined, U-Boot will use a device tree
944 to configure its devices, instead of relying on statically
945 compiled #defines in the board file. This option is
946 experimental and only available on a few boards. The device
947 tree is available in the global data as gd->fdt_blob.
949 U-Boot needs to get its device tree from somewhere. This can
950 be done using one of the two options below:
953 If this variable is defined, U-Boot will embed a device tree
954 binary in its image. This device tree file should be in the
955 board directory and called <soc>-<board>.dts. The binary file
956 is then picked up in board_init_f() and made available through
957 the global data structure as gd->blob.
960 If this variable is defined, U-Boot will build a device tree
961 binary. It will be called u-boot.dtb. Architecture-specific
962 code will locate it at run-time. Generally this works by:
964 cat u-boot.bin u-boot.dtb >image.bin
966 and in fact, U-Boot does this for you, creating a file called
967 u-boot-dtb.bin which is useful in the common case. You can
968 still use the individual files if you need something more
973 If this variable is defined, it enables watchdog
974 support for the SoC. There must be support in the SoC
975 specific code for a watchdog. For the 8xx and 8260
976 CPUs, the SIU Watchdog feature is enabled in the SYPCR
977 register. When supported for a specific SoC is
978 available, then no further board specific code should
982 When using a watchdog circuitry external to the used
983 SoC, then define this variable and provide board
984 specific code for the "hw_watchdog_reset" function.
987 CONFIG_VERSION_VARIABLE
988 If this variable is defined, an environment variable
989 named "ver" is created by U-Boot showing the U-Boot
990 version as printed by the "version" command.
991 Any change to this variable will be reverted at the
996 When CONFIG_CMD_DATE is selected, the type of the RTC
997 has to be selected, too. Define exactly one of the
1000 CONFIG_RTC_MPC8xx - use internal RTC of MPC8xx
1001 CONFIG_RTC_PCF8563 - use Philips PCF8563 RTC
1002 CONFIG_RTC_MC13XXX - use MC13783 or MC13892 RTC
1003 CONFIG_RTC_MC146818 - use MC146818 RTC
1004 CONFIG_RTC_DS1307 - use Maxim, Inc. DS1307 RTC
1005 CONFIG_RTC_DS1337 - use Maxim, Inc. DS1337 RTC
1006 CONFIG_RTC_DS1338 - use Maxim, Inc. DS1338 RTC
1007 CONFIG_RTC_DS164x - use Dallas DS164x RTC
1008 CONFIG_RTC_ISL1208 - use Intersil ISL1208 RTC
1009 CONFIG_RTC_MAX6900 - use Maxim, Inc. MAX6900 RTC
1010 CONFIG_SYS_RTC_DS1337_NOOSC - Turn off the OSC output for DS1337
1011 CONFIG_SYS_RV3029_TCR - enable trickle charger on
1014 Note that if the RTC uses I2C, then the I2C interface
1015 must also be configured. See I2C Support, below.
1018 CONFIG_PCA953X - use NXP's PCA953X series I2C GPIO
1019 CONFIG_PCA953X_INFO - enable pca953x info command
1021 The CONFIG_SYS_I2C_PCA953X_WIDTH option specifies a list of
1022 chip-ngpio pairs that tell the PCA953X driver the number of
1023 pins supported by a particular chip.
1025 Note that if the GPIO device uses I2C, then the I2C interface
1026 must also be configured. See I2C Support, below.
1028 - Timestamp Support:
1030 When CONFIG_TIMESTAMP is selected, the timestamp
1031 (date and time) of an image is printed by image
1032 commands like bootm or iminfo. This option is
1033 automatically enabled when you select CONFIG_CMD_DATE .
1035 - Partition Labels (disklabels) Supported:
1036 Zero or more of the following:
1037 CONFIG_MAC_PARTITION Apple's MacOS partition table.
1038 CONFIG_DOS_PARTITION MS Dos partition table, traditional on the
1039 Intel architecture, USB sticks, etc.
1040 CONFIG_ISO_PARTITION ISO partition table, used on CDROM etc.
1041 CONFIG_EFI_PARTITION GPT partition table, common when EFI is the
1042 bootloader. Note 2TB partition limit; see
1044 CONFIG_MTD_PARTITIONS Memory Technology Device partition table.
1046 If IDE or SCSI support is enabled (CONFIG_CMD_IDE or
1047 CONFIG_CMD_SCSI) you must configure support for at
1048 least one non-MTD partition type as well.
1051 CONFIG_IDE_RESET_ROUTINE - this is defined in several
1052 board configurations files but used nowhere!
1054 CONFIG_IDE_RESET - is this is defined, IDE Reset will
1055 be performed by calling the function
1056 ide_set_reset(int reset)
1057 which has to be defined in a board specific file
1062 Set this to enable ATAPI support.
1067 Set this to enable support for disks larger than 137GB
1068 Also look at CONFIG_SYS_64BIT_LBA.
1069 Whithout these , LBA48 support uses 32bit variables and will 'only'
1070 support disks up to 2.1TB.
1072 CONFIG_SYS_64BIT_LBA:
1073 When enabled, makes the IDE subsystem use 64bit sector addresses.
1077 At the moment only there is only support for the
1078 SYM53C8XX SCSI controller; define
1079 CONFIG_SCSI_SYM53C8XX to enable it.
1081 CONFIG_SYS_SCSI_MAX_LUN [8], CONFIG_SYS_SCSI_MAX_SCSI_ID [7] and
1082 CONFIG_SYS_SCSI_MAX_DEVICE [CONFIG_SYS_SCSI_MAX_SCSI_ID *
1083 CONFIG_SYS_SCSI_MAX_LUN] can be adjusted to define the
1084 maximum numbers of LUNs, SCSI ID's and target
1086 CONFIG_SYS_SCSI_SYM53C8XX_CCF to fix clock timing (80Mhz)
1088 The environment variable 'scsidevs' is set to the number of
1089 SCSI devices found during the last scan.
1091 - NETWORK Support (PCI):
1093 Support for Intel 8254x/8257x gigabit chips.
1096 Utility code for direct access to the SPI bus on Intel 8257x.
1097 This does not do anything useful unless you set at least one
1098 of CONFIG_CMD_E1000 or CONFIG_E1000_SPI_GENERIC.
1100 CONFIG_E1000_SPI_GENERIC
1101 Allow generic access to the SPI bus on the Intel 8257x, for
1102 example with the "sspi" command.
1105 Management command for E1000 devices. When used on devices
1106 with SPI support you can reprogram the EEPROM from U-Boot.
1108 CONFIG_E1000_FALLBACK_MAC
1109 default MAC for empty EEPROM after production.
1112 Support for Intel 82557/82559/82559ER chips.
1113 Optional CONFIG_EEPRO100_SROM_WRITE enables EEPROM
1114 write routine for first time initialisation.
1117 Support for Digital 2114x chips.
1118 Optional CONFIG_TULIP_SELECT_MEDIA for board specific
1119 modem chip initialisation (KS8761/QS6611).
1122 Support for National dp83815 chips.
1125 Support for National dp8382[01] gigabit chips.
1127 - NETWORK Support (other):
1129 CONFIG_DRIVER_AT91EMAC
1130 Support for AT91RM9200 EMAC.
1133 Define this to use reduced MII inteface
1135 CONFIG_DRIVER_AT91EMAC_QUIET
1136 If this defined, the driver is quiet.
1137 The driver doen't show link status messages.
1139 CONFIG_CALXEDA_XGMAC
1140 Support for the Calxeda XGMAC device
1143 Support for SMSC's LAN91C96 chips.
1145 CONFIG_LAN91C96_BASE
1146 Define this to hold the physical address
1147 of the LAN91C96's I/O space
1149 CONFIG_LAN91C96_USE_32_BIT
1150 Define this to enable 32 bit addressing
1153 Support for SMSC's LAN91C111 chip
1155 CONFIG_SMC91111_BASE
1156 Define this to hold the physical address
1157 of the device (I/O space)
1159 CONFIG_SMC_USE_32_BIT
1160 Define this if data bus is 32 bits
1162 CONFIG_SMC_USE_IOFUNCS
1163 Define this to use i/o functions instead of macros
1164 (some hardware wont work with macros)
1166 CONFIG_DRIVER_TI_EMAC
1167 Support for davinci emac
1169 CONFIG_SYS_DAVINCI_EMAC_PHY_COUNT
1170 Define this if you have more then 3 PHYs.
1173 Support for Faraday's FTGMAC100 Gigabit SoC Ethernet
1175 CONFIG_FTGMAC100_EGIGA
1176 Define this to use GE link update with gigabit PHY.
1177 Define this if FTGMAC100 is connected to gigabit PHY.
1178 If your system has 10/100 PHY only, it might not occur
1179 wrong behavior. Because PHY usually return timeout or
1180 useless data when polling gigabit status and gigabit
1181 control registers. This behavior won't affect the
1182 correctnessof 10/100 link speed update.
1185 Support for SMSC's LAN911x and LAN921x chips
1188 Define this to hold the physical address
1189 of the device (I/O space)
1191 CONFIG_SMC911X_32_BIT
1192 Define this if data bus is 32 bits
1194 CONFIG_SMC911X_16_BIT
1195 Define this if data bus is 16 bits. If your processor
1196 automatically converts one 32 bit word to two 16 bit
1197 words you may also try CONFIG_SMC911X_32_BIT.
1200 Support for Renesas on-chip Ethernet controller
1202 CONFIG_SH_ETHER_USE_PORT
1203 Define the number of ports to be used
1205 CONFIG_SH_ETHER_PHY_ADDR
1206 Define the ETH PHY's address
1208 CONFIG_SH_ETHER_CACHE_WRITEBACK
1209 If this option is set, the driver enables cache flush.
1212 CONFIG_GENERIC_LPC_TPM
1213 Support for generic parallel port TPM devices. Only one device
1214 per system is supported at this time.
1216 CONFIG_TPM_TIS_BASE_ADDRESS
1217 Base address where the generic TPM device is mapped
1218 to. Contemporary x86 systems usually map it at
1222 At the moment only the UHCI host controller is
1223 supported (PIP405, MIP405, MPC5200); define
1224 CONFIG_USB_UHCI to enable it.
1225 define CONFIG_USB_KEYBOARD to enable the USB Keyboard
1226 and define CONFIG_USB_STORAGE to enable the USB
1229 Supported are USB Keyboards and USB Floppy drives
1231 MPC5200 USB requires additional defines:
1233 for 528 MHz Clock: 0x0001bbbb
1237 for differential drivers: 0x00001000
1238 for single ended drivers: 0x00005000
1239 for differential drivers on PSC3: 0x00000100
1240 for single ended drivers on PSC3: 0x00004100
1241 CONFIG_SYS_USB_EVENT_POLL
1242 May be defined to allow interrupt polling
1243 instead of using asynchronous interrupts
1245 CONFIG_USB_EHCI_TXFIFO_THRESH enables setting of the
1246 txfilltuning field in the EHCI controller on reset.
1249 Define the below if you wish to use the USB console.
1250 Once firmware is rebuilt from a serial console issue the
1251 command "setenv stdin usbtty; setenv stdout usbtty" and
1252 attach your USB cable. The Unix command "dmesg" should print
1253 it has found a new device. The environment variable usbtty
1254 can be set to gserial or cdc_acm to enable your device to
1255 appear to a USB host as a Linux gserial device or a
1256 Common Device Class Abstract Control Model serial device.
1257 If you select usbtty = gserial you should be able to enumerate
1259 # modprobe usbserial vendor=0xVendorID product=0xProductID
1260 else if using cdc_acm, simply setting the environment
1261 variable usbtty to be cdc_acm should suffice. The following
1262 might be defined in YourBoardName.h
1265 Define this to build a UDC device
1268 Define this to have a tty type of device available to
1269 talk to the UDC device
1272 Define this to enable the high speed support for usb
1273 device and usbtty. If this feature is enabled, a routine
1274 int is_usbd_high_speed(void)
1275 also needs to be defined by the driver to dynamically poll
1276 whether the enumeration has succeded at high speed or full
1279 CONFIG_SYS_CONSOLE_IS_IN_ENV
1280 Define this if you want stdin, stdout &/or stderr to
1284 CONFIG_SYS_USB_EXTC_CLK 0xBLAH
1285 Derive USB clock from external clock "blah"
1286 - CONFIG_SYS_USB_EXTC_CLK 0x02
1288 CONFIG_SYS_USB_BRG_CLK 0xBLAH
1289 Derive USB clock from brgclk
1290 - CONFIG_SYS_USB_BRG_CLK 0x04
1292 If you have a USB-IF assigned VendorID then you may wish to
1293 define your own vendor specific values either in BoardName.h
1294 or directly in usbd_vendor_info.h. If you don't define
1295 CONFIG_USBD_MANUFACTURER, CONFIG_USBD_PRODUCT_NAME,
1296 CONFIG_USBD_VENDORID and CONFIG_USBD_PRODUCTID, then U-Boot
1297 should pretend to be a Linux device to it's target host.
1299 CONFIG_USBD_MANUFACTURER
1300 Define this string as the name of your company for
1301 - CONFIG_USBD_MANUFACTURER "my company"
1303 CONFIG_USBD_PRODUCT_NAME
1304 Define this string as the name of your product
1305 - CONFIG_USBD_PRODUCT_NAME "acme usb device"
1307 CONFIG_USBD_VENDORID
1308 Define this as your assigned Vendor ID from the USB
1309 Implementors Forum. This *must* be a genuine Vendor ID
1310 to avoid polluting the USB namespace.
1311 - CONFIG_USBD_VENDORID 0xFFFF
1313 CONFIG_USBD_PRODUCTID
1314 Define this as the unique Product ID
1316 - CONFIG_USBD_PRODUCTID 0xFFFF
1318 - ULPI Layer Support:
1319 The ULPI (UTMI Low Pin (count) Interface) PHYs are supported via
1320 the generic ULPI layer. The generic layer accesses the ULPI PHY
1321 via the platform viewport, so you need both the genric layer and
1322 the viewport enabled. Currently only Chipidea/ARC based
1323 viewport is supported.
1324 To enable the ULPI layer support, define CONFIG_USB_ULPI and
1325 CONFIG_USB_ULPI_VIEWPORT in your board configuration file.
1326 If your ULPI phy needs a different reference clock than the
1327 standard 24 MHz then you have to define CONFIG_ULPI_REF_CLK to
1328 the appropriate value in Hz.
1331 The MMC controller on the Intel PXA is supported. To
1332 enable this define CONFIG_MMC. The MMC can be
1333 accessed from the boot prompt by mapping the device
1334 to physical memory similar to flash. Command line is
1335 enabled with CONFIG_CMD_MMC. The MMC driver also works with
1336 the FAT fs. This is enabled with CONFIG_CMD_FAT.
1339 Support for Renesas on-chip MMCIF controller
1341 CONFIG_SH_MMCIF_ADDR
1342 Define the base address of MMCIF registers
1345 Define the clock frequency for MMCIF
1347 - Journaling Flash filesystem support:
1348 CONFIG_JFFS2_NAND, CONFIG_JFFS2_NAND_OFF, CONFIG_JFFS2_NAND_SIZE,
1349 CONFIG_JFFS2_NAND_DEV
1350 Define these for a default partition on a NAND device
1352 CONFIG_SYS_JFFS2_FIRST_SECTOR,
1353 CONFIG_SYS_JFFS2_FIRST_BANK, CONFIG_SYS_JFFS2_NUM_BANKS
1354 Define these for a default partition on a NOR device
1356 CONFIG_SYS_JFFS_CUSTOM_PART
1357 Define this to create an own partition. You have to provide a
1358 function struct part_info* jffs2_part_info(int part_num)
1360 If you define only one JFFS2 partition you may also want to
1361 #define CONFIG_SYS_JFFS_SINGLE_PART 1
1362 to disable the command chpart. This is the default when you
1363 have not defined a custom partition
1365 - FAT(File Allocation Table) filesystem write function support:
1368 Define this to enable support for saving memory data as a
1369 file in FAT formatted partition.
1371 This will also enable the command "fatwrite" enabling the
1372 user to write files to FAT.
1374 CBFS (Coreboot Filesystem) support
1377 Define this to enable support for reading from a Coreboot
1378 filesystem. Available commands are cbfsinit, cbfsinfo, cbfsls
1384 Define this to enable standard (PC-Style) keyboard
1388 Standard PC keyboard driver with US (is default) and
1389 GERMAN key layout (switch via environment 'keymap=de') support.
1390 Export function i8042_kbd_init, i8042_tstc and i8042_getc
1391 for cfb_console. Supports cursor blinking.
1396 Define this to enable video support (for output to
1399 CONFIG_VIDEO_CT69000
1401 Enable Chips & Technologies 69000 Video chip
1403 CONFIG_VIDEO_SMI_LYNXEM
1404 Enable Silicon Motion SMI 712/710/810 Video chip. The
1405 video output is selected via environment 'videoout'
1406 (1 = LCD and 2 = CRT). If videoout is undefined, CRT is
1409 For the CT69000 and SMI_LYNXEM drivers, videomode is
1410 selected via environment 'videomode'. Two different ways
1412 - "videomode=num" 'num' is a standard LiLo mode numbers.
1413 Following standard modes are supported (* is default):
1415 Colors 640x480 800x600 1024x768 1152x864 1280x1024
1416 -------------+---------------------------------------------
1417 8 bits | 0x301* 0x303 0x305 0x161 0x307
1418 15 bits | 0x310 0x313 0x316 0x162 0x319
1419 16 bits | 0x311 0x314 0x317 0x163 0x31A
1420 24 bits | 0x312 0x315 0x318 ? 0x31B
1421 -------------+---------------------------------------------
1422 (i.e. setenv videomode 317; saveenv; reset;)
1424 - "videomode=bootargs" all the video parameters are parsed
1425 from the bootargs. (See drivers/video/videomodes.c)
1428 CONFIG_VIDEO_SED13806
1429 Enable Epson SED13806 driver. This driver supports 8bpp
1430 and 16bpp modes defined by CONFIG_VIDEO_SED13806_8BPP
1431 or CONFIG_VIDEO_SED13806_16BPP
1434 Enable the Freescale DIU video driver. Reference boards for
1435 SOCs that have a DIU should define this macro to enable DIU
1436 support, and should also define these other macros:
1442 CONFIG_VIDEO_SW_CURSOR
1443 CONFIG_VGA_AS_SINGLE_DEVICE
1445 CONFIG_VIDEO_BMP_LOGO
1447 The DIU driver will look for the 'video-mode' environment
1448 variable, and if defined, enable the DIU as a console during
1449 boot. See the documentation file README.video for a
1450 description of this variable.
1454 Enable the VGA video / BIOS for x86. The alternative if you
1455 are using coreboot is to use the coreboot frame buffer
1462 Define this to enable a custom keyboard support.
1463 This simply calls drv_keyboard_init() which must be
1464 defined in your board-specific files.
1465 The only board using this so far is RBC823.
1467 - LCD Support: CONFIG_LCD
1469 Define this to enable LCD support (for output to LCD
1470 display); also select one of the supported displays
1471 by defining one of these:
1475 HITACHI TX09D70VM1CCA, 3.5", 240x320.
1477 CONFIG_NEC_NL6448AC33:
1479 NEC NL6448AC33-18. Active, color, single scan.
1481 CONFIG_NEC_NL6448BC20
1483 NEC NL6448BC20-08. 6.5", 640x480.
1484 Active, color, single scan.
1486 CONFIG_NEC_NL6448BC33_54
1488 NEC NL6448BC33-54. 10.4", 640x480.
1489 Active, color, single scan.
1493 Sharp 320x240. Active, color, single scan.
1494 It isn't 16x9, and I am not sure what it is.
1496 CONFIG_SHARP_LQ64D341
1498 Sharp LQ64D341 display, 640x480.
1499 Active, color, single scan.
1503 HLD1045 display, 640x480.
1504 Active, color, single scan.
1508 Optrex CBL50840-2 NF-FW 99 22 M5
1510 Hitachi LMG6912RPFC-00T
1514 320x240. Black & white.
1516 Normally display is black on white background; define
1517 CONFIG_SYS_WHITE_ON_BLACK to get it inverted.
1519 CONFIG_LCD_ALIGNMENT
1521 Normally the LCD is page-aligned (tyically 4KB). If this is
1522 defined then the LCD will be aligned to this value instead.
1523 For ARM it is sometimes useful to use MMU_SECTION_SIZE
1524 here, since it is cheaper to change data cache settings on
1525 a per-section basis.
1527 CONFIG_CONSOLE_SCROLL_LINES
1529 When the console need to be scrolled, this is the number of
1530 lines to scroll by. It defaults to 1. Increasing this makes
1531 the console jump but can help speed up operation when scrolling
1536 Support drawing of RLE8-compressed bitmaps on the LCD.
1540 Enables an 'i2c edid' command which can read EDID
1541 information over I2C from an attached LCD display.
1543 - Splash Screen Support: CONFIG_SPLASH_SCREEN
1545 If this option is set, the environment is checked for
1546 a variable "splashimage". If found, the usual display
1547 of logo, copyright and system information on the LCD
1548 is suppressed and the BMP image at the address
1549 specified in "splashimage" is loaded instead. The
1550 console is redirected to the "nulldev", too. This
1551 allows for a "silent" boot where a splash screen is
1552 loaded very quickly after power-on.
1554 CONFIG_SPLASHIMAGE_GUARD
1556 If this option is set, then U-Boot will prevent the environment
1557 variable "splashimage" from being set to a problematic address
1558 (see README.displaying-bmps and README.arm-unaligned-accesses).
1559 This option is useful for targets where, due to alignment
1560 restrictions, an improperly aligned BMP image will cause a data
1561 abort. If you think you will not have problems with unaligned
1562 accesses (for example because your toolchain prevents them)
1563 there is no need to set this option.
1565 CONFIG_SPLASH_SCREEN_ALIGN
1567 If this option is set the splash image can be freely positioned
1568 on the screen. Environment variable "splashpos" specifies the
1569 position as "x,y". If a positive number is given it is used as
1570 number of pixel from left/top. If a negative number is given it
1571 is used as number of pixel from right/bottom. You can also
1572 specify 'm' for centering the image.
1575 setenv splashpos m,m
1576 => image at center of screen
1578 setenv splashpos 30,20
1579 => image at x = 30 and y = 20
1581 setenv splashpos -10,m
1582 => vertically centered image
1583 at x = dspWidth - bmpWidth - 9
1585 CONFIG_SPLASH_SCREEN_PREPARE
1587 If this option is set then the board_splash_screen_prepare()
1588 function, which must be defined in your code, is called as part
1589 of the splash screen display sequence. It gives the board an
1590 opportunity to prepare the splash image data before it is
1591 processed and sent to the frame buffer by U-Boot.
1593 - Gzip compressed BMP image support: CONFIG_VIDEO_BMP_GZIP
1595 If this option is set, additionally to standard BMP
1596 images, gzipped BMP images can be displayed via the
1597 splashscreen support or the bmp command.
1599 - Run length encoded BMP image (RLE8) support: CONFIG_VIDEO_BMP_RLE8
1601 If this option is set, 8-bit RLE compressed BMP images
1602 can be displayed via the splashscreen support or the
1605 - Do compresssing for memory range:
1608 If this option is set, it would use zlib deflate method
1609 to compress the specified memory at its best effort.
1611 - Compression support:
1614 If this option is set, support for bzip2 compressed
1615 images is included. If not, only uncompressed and gzip
1616 compressed images are supported.
1618 NOTE: the bzip2 algorithm requires a lot of RAM, so
1619 the malloc area (as defined by CONFIG_SYS_MALLOC_LEN) should
1624 If this option is set, support for lzma compressed
1627 Note: The LZMA algorithm adds between 2 and 4KB of code and it
1628 requires an amount of dynamic memory that is given by the
1631 (1846 + 768 << (lc + lp)) * sizeof(uint16)
1633 Where lc and lp stand for, respectively, Literal context bits
1634 and Literal pos bits.
1636 This value is upper-bounded by 14MB in the worst case. Anyway,
1637 for a ~4MB large kernel image, we have lc=3 and lp=0 for a
1638 total amount of (1846 + 768 << (3 + 0)) * 2 = ~41KB... that is
1639 a very small buffer.
1641 Use the lzmainfo tool to determinate the lc and lp values and
1642 then calculate the amount of needed dynamic memory (ensuring
1643 the appropriate CONFIG_SYS_MALLOC_LEN value).
1648 The address of PHY on MII bus.
1650 CONFIG_PHY_CLOCK_FREQ (ppc4xx)
1652 The clock frequency of the MII bus
1656 If this option is set, support for speed/duplex
1657 detection of gigabit PHY is included.
1659 CONFIG_PHY_RESET_DELAY
1661 Some PHY like Intel LXT971A need extra delay after
1662 reset before any MII register access is possible.
1663 For such PHY, set this option to the usec delay
1664 required. (minimum 300usec for LXT971A)
1666 CONFIG_PHY_CMD_DELAY (ppc4xx)
1668 Some PHY like Intel LXT971A need extra delay after
1669 command issued before MII status register can be read
1679 Define a default value for Ethernet address to use
1680 for the respective Ethernet interface, in case this
1681 is not determined automatically.
1686 Define a default value for the IP address to use for
1687 the default Ethernet interface, in case this is not
1688 determined through e.g. bootp.
1689 (Environment variable "ipaddr")
1691 - Server IP address:
1694 Defines a default value for the IP address of a TFTP
1695 server to contact when using the "tftboot" command.
1696 (Environment variable "serverip")
1698 CONFIG_KEEP_SERVERADDR
1700 Keeps the server's MAC address, in the env 'serveraddr'
1701 for passing to bootargs (like Linux's netconsole option)
1703 - Gateway IP address:
1706 Defines a default value for the IP address of the
1707 default router where packets to other networks are
1709 (Environment variable "gatewayip")
1714 Defines a default value for the subnet mask (or
1715 routing prefix) which is used to determine if an IP
1716 address belongs to the local subnet or needs to be
1717 forwarded through a router.
1718 (Environment variable "netmask")
1720 - Multicast TFTP Mode:
1723 Defines whether you want to support multicast TFTP as per
1724 rfc-2090; for example to work with atftp. Lets lots of targets
1725 tftp down the same boot image concurrently. Note: the Ethernet
1726 driver in use must provide a function: mcast() to join/leave a
1729 - BOOTP Recovery Mode:
1730 CONFIG_BOOTP_RANDOM_DELAY
1732 If you have many targets in a network that try to
1733 boot using BOOTP, you may want to avoid that all
1734 systems send out BOOTP requests at precisely the same
1735 moment (which would happen for instance at recovery
1736 from a power failure, when all systems will try to
1737 boot, thus flooding the BOOTP server. Defining
1738 CONFIG_BOOTP_RANDOM_DELAY causes a random delay to be
1739 inserted before sending out BOOTP requests. The
1740 following delays are inserted then:
1742 1st BOOTP request: delay 0 ... 1 sec
1743 2nd BOOTP request: delay 0 ... 2 sec
1744 3rd BOOTP request: delay 0 ... 4 sec
1746 BOOTP requests: delay 0 ... 8 sec
1748 - DHCP Advanced Options:
1749 You can fine tune the DHCP functionality by defining
1750 CONFIG_BOOTP_* symbols:
1752 CONFIG_BOOTP_SUBNETMASK
1753 CONFIG_BOOTP_GATEWAY
1754 CONFIG_BOOTP_HOSTNAME
1755 CONFIG_BOOTP_NISDOMAIN
1756 CONFIG_BOOTP_BOOTPATH
1757 CONFIG_BOOTP_BOOTFILESIZE
1760 CONFIG_BOOTP_SEND_HOSTNAME
1761 CONFIG_BOOTP_NTPSERVER
1762 CONFIG_BOOTP_TIMEOFFSET
1763 CONFIG_BOOTP_VENDOREX
1764 CONFIG_BOOTP_MAY_FAIL
1766 CONFIG_BOOTP_SERVERIP - TFTP server will be the serverip
1767 environment variable, not the BOOTP server.
1769 CONFIG_BOOTP_MAY_FAIL - If the DHCP server is not found
1770 after the configured retry count, the call will fail
1771 instead of starting over. This can be used to fail over
1772 to Link-local IP address configuration if the DHCP server
1775 CONFIG_BOOTP_DNS2 - If a DHCP client requests the DNS
1776 serverip from a DHCP server, it is possible that more
1777 than one DNS serverip is offered to the client.
1778 If CONFIG_BOOTP_DNS2 is enabled, the secondary DNS
1779 serverip will be stored in the additional environment
1780 variable "dnsip2". The first DNS serverip is always
1781 stored in the variable "dnsip", when CONFIG_BOOTP_DNS
1784 CONFIG_BOOTP_SEND_HOSTNAME - Some DHCP servers are capable
1785 to do a dynamic update of a DNS server. To do this, they
1786 need the hostname of the DHCP requester.
1787 If CONFIG_BOOTP_SEND_HOSTNAME is defined, the content
1788 of the "hostname" environment variable is passed as
1789 option 12 to the DHCP server.
1791 CONFIG_BOOTP_DHCP_REQUEST_DELAY
1793 A 32bit value in microseconds for a delay between
1794 receiving a "DHCP Offer" and sending the "DHCP Request".
1795 This fixes a problem with certain DHCP servers that don't
1796 respond 100% of the time to a "DHCP request". E.g. On an
1797 AT91RM9200 processor running at 180MHz, this delay needed
1798 to be *at least* 15,000 usec before a Windows Server 2003
1799 DHCP server would reply 100% of the time. I recommend at
1800 least 50,000 usec to be safe. The alternative is to hope
1801 that one of the retries will be successful but note that
1802 the DHCP timeout and retry process takes a longer than
1805 - Link-local IP address negotiation:
1806 Negotiate with other link-local clients on the local network
1807 for an address that doesn't require explicit configuration.
1808 This is especially useful if a DHCP server cannot be guaranteed
1809 to exist in all environments that the device must operate.
1811 See doc/README.link-local for more information.
1814 CONFIG_CDP_DEVICE_ID
1816 The device id used in CDP trigger frames.
1818 CONFIG_CDP_DEVICE_ID_PREFIX
1820 A two character string which is prefixed to the MAC address
1825 A printf format string which contains the ascii name of
1826 the port. Normally is set to "eth%d" which sets
1827 eth0 for the first Ethernet, eth1 for the second etc.
1829 CONFIG_CDP_CAPABILITIES
1831 A 32bit integer which indicates the device capabilities;
1832 0x00000010 for a normal host which does not forwards.
1836 An ascii string containing the version of the software.
1840 An ascii string containing the name of the platform.
1844 A 32bit integer sent on the trigger.
1846 CONFIG_CDP_POWER_CONSUMPTION
1848 A 16bit integer containing the power consumption of the
1849 device in .1 of milliwatts.
1851 CONFIG_CDP_APPLIANCE_VLAN_TYPE
1853 A byte containing the id of the VLAN.
1855 - Status LED: CONFIG_STATUS_LED
1857 Several configurations allow to display the current
1858 status using a LED. For instance, the LED will blink
1859 fast while running U-Boot code, stop blinking as
1860 soon as a reply to a BOOTP request was received, and
1861 start blinking slow once the Linux kernel is running
1862 (supported by a status LED driver in the Linux
1863 kernel). Defining CONFIG_STATUS_LED enables this
1866 - CAN Support: CONFIG_CAN_DRIVER
1868 Defining CONFIG_CAN_DRIVER enables CAN driver support
1869 on those systems that support this (optional)
1870 feature, like the TQM8xxL modules.
1872 - I2C Support: CONFIG_HARD_I2C | CONFIG_SOFT_I2C
1874 These enable I2C serial bus commands. Defining either of
1875 (but not both of) CONFIG_HARD_I2C or CONFIG_SOFT_I2C will
1876 include the appropriate I2C driver for the selected CPU.
1878 This will allow you to use i2c commands at the u-boot
1879 command line (as long as you set CONFIG_CMD_I2C in
1880 CONFIG_COMMANDS) and communicate with i2c based realtime
1881 clock chips. See common/cmd_i2c.c for a description of the
1882 command line interface.
1884 CONFIG_HARD_I2C selects a hardware I2C controller.
1886 CONFIG_SOFT_I2C configures u-boot to use a software (aka
1887 bit-banging) driver instead of CPM or similar hardware
1890 There are several other quantities that must also be
1891 defined when you define CONFIG_HARD_I2C or CONFIG_SOFT_I2C.
1893 In both cases you will need to define CONFIG_SYS_I2C_SPEED
1894 to be the frequency (in Hz) at which you wish your i2c bus
1895 to run and CONFIG_SYS_I2C_SLAVE to be the address of this node (ie
1896 the CPU's i2c node address).
1898 Now, the u-boot i2c code for the mpc8xx
1899 (arch/powerpc/cpu/mpc8xx/i2c.c) sets the CPU up as a master node
1900 and so its address should therefore be cleared to 0 (See,
1901 eg, MPC823e User's Manual p.16-473). So, set
1902 CONFIG_SYS_I2C_SLAVE to 0.
1904 CONFIG_SYS_I2C_INIT_MPC5XXX
1906 When a board is reset during an i2c bus transfer
1907 chips might think that the current transfer is still
1908 in progress. Reset the slave devices by sending start
1909 commands until the slave device responds.
1911 That's all that's required for CONFIG_HARD_I2C.
1913 If you use the software i2c interface (CONFIG_SOFT_I2C)
1914 then the following macros need to be defined (examples are
1915 from include/configs/lwmon.h):
1919 (Optional). Any commands necessary to enable the I2C
1920 controller or configure ports.
1922 eg: #define I2C_INIT (immr->im_cpm.cp_pbdir |= PB_SCL)
1926 (Only for MPC8260 CPU). The I/O port to use (the code
1927 assumes both bits are on the same port). Valid values
1928 are 0..3 for ports A..D.
1932 The code necessary to make the I2C data line active
1933 (driven). If the data line is open collector, this
1936 eg: #define I2C_ACTIVE (immr->im_cpm.cp_pbdir |= PB_SDA)
1940 The code necessary to make the I2C data line tri-stated
1941 (inactive). If the data line is open collector, this
1944 eg: #define I2C_TRISTATE (immr->im_cpm.cp_pbdir &= ~PB_SDA)
1948 Code that returns true if the I2C data line is high,
1951 eg: #define I2C_READ ((immr->im_cpm.cp_pbdat & PB_SDA) != 0)
1955 If <bit> is true, sets the I2C data line high. If it
1956 is false, it clears it (low).
1958 eg: #define I2C_SDA(bit) \
1959 if(bit) immr->im_cpm.cp_pbdat |= PB_SDA; \
1960 else immr->im_cpm.cp_pbdat &= ~PB_SDA
1964 If <bit> is true, sets the I2C clock line high. If it
1965 is false, it clears it (low).
1967 eg: #define I2C_SCL(bit) \
1968 if(bit) immr->im_cpm.cp_pbdat |= PB_SCL; \
1969 else immr->im_cpm.cp_pbdat &= ~PB_SCL
1973 This delay is invoked four times per clock cycle so this
1974 controls the rate of data transfer. The data rate thus
1975 is 1 / (I2C_DELAY * 4). Often defined to be something
1978 #define I2C_DELAY udelay(2)
1980 CONFIG_SOFT_I2C_GPIO_SCL / CONFIG_SOFT_I2C_GPIO_SDA
1982 If your arch supports the generic GPIO framework (asm/gpio.h),
1983 then you may alternatively define the two GPIOs that are to be
1984 used as SCL / SDA. Any of the previous I2C_xxx macros will
1985 have GPIO-based defaults assigned to them as appropriate.
1987 You should define these to the GPIO value as given directly to
1988 the generic GPIO functions.
1990 CONFIG_SYS_I2C_INIT_BOARD
1992 When a board is reset during an i2c bus transfer
1993 chips might think that the current transfer is still
1994 in progress. On some boards it is possible to access
1995 the i2c SCLK line directly, either by using the
1996 processor pin as a GPIO or by having a second pin
1997 connected to the bus. If this option is defined a
1998 custom i2c_init_board() routine in boards/xxx/board.c
1999 is run early in the boot sequence.
2001 CONFIG_SYS_I2C_BOARD_LATE_INIT
2003 An alternative to CONFIG_SYS_I2C_INIT_BOARD. If this option is
2004 defined a custom i2c_board_late_init() routine in
2005 boards/xxx/board.c is run AFTER the operations in i2c_init()
2006 is completed. This callpoint can be used to unreset i2c bus
2007 using CPU i2c controller register accesses for CPUs whose i2c
2008 controller provide such a method. It is called at the end of
2009 i2c_init() to allow i2c_init operations to setup the i2c bus
2010 controller on the CPU (e.g. setting bus speed & slave address).
2012 CONFIG_I2CFAST (PPC405GP|PPC405EP only)
2014 This option enables configuration of bi_iic_fast[] flags
2015 in u-boot bd_info structure based on u-boot environment
2016 variable "i2cfast". (see also i2cfast)
2018 CONFIG_I2C_MULTI_BUS
2020 This option allows the use of multiple I2C buses, each of which
2021 must have a controller. At any point in time, only one bus is
2022 active. To switch to a different bus, use the 'i2c dev' command.
2023 Note that bus numbering is zero-based.
2025 CONFIG_SYS_I2C_NOPROBES
2027 This option specifies a list of I2C devices that will be skipped
2028 when the 'i2c probe' command is issued. If CONFIG_I2C_MULTI_BUS
2029 is set, specify a list of bus-device pairs. Otherwise, specify
2030 a 1D array of device addresses
2033 #undef CONFIG_I2C_MULTI_BUS
2034 #define CONFIG_SYS_I2C_NOPROBES {0x50,0x68}
2036 will skip addresses 0x50 and 0x68 on a board with one I2C bus
2038 #define CONFIG_I2C_MULTI_BUS
2039 #define CONFIG_SYS_I2C_MULTI_NOPROBES {{0,0x50},{0,0x68},{1,0x54}}
2041 will skip addresses 0x50 and 0x68 on bus 0 and address 0x54 on bus 1
2043 CONFIG_SYS_SPD_BUS_NUM
2045 If defined, then this indicates the I2C bus number for DDR SPD.
2046 If not defined, then U-Boot assumes that SPD is on I2C bus 0.
2048 CONFIG_SYS_RTC_BUS_NUM
2050 If defined, then this indicates the I2C bus number for the RTC.
2051 If not defined, then U-Boot assumes that RTC is on I2C bus 0.
2053 CONFIG_SYS_DTT_BUS_NUM
2055 If defined, then this indicates the I2C bus number for the DTT.
2056 If not defined, then U-Boot assumes that DTT is on I2C bus 0.
2058 CONFIG_SYS_I2C_DTT_ADDR:
2060 If defined, specifies the I2C address of the DTT device.
2061 If not defined, then U-Boot uses predefined value for
2062 specified DTT device.
2066 Define this option if you want to use Freescale's I2C driver in
2067 drivers/i2c/fsl_i2c.c.
2071 Define this option if you have I2C devices reached over 1 .. n
2072 I2C Muxes like the pca9544a. This option addes a new I2C
2073 Command "i2c bus [muxtype:muxaddr:muxchannel]" which adds a
2074 new I2C Bus to the existing I2C Busses. If you select the
2075 new Bus with "i2c dev", u-bbot sends first the commandos for
2076 the muxes to activate this new "bus".
2078 CONFIG_I2C_MULTI_BUS must be also defined, to use this
2082 Adding a new I2C Bus reached over 2 pca9544a muxes
2083 The First mux with address 70 and channel 6
2084 The Second mux with address 71 and channel 4
2086 => i2c bus pca9544a:70:6:pca9544a:71:4
2088 Use the "i2c bus" command without parameter, to get a list
2089 of I2C Busses with muxes:
2092 Busses reached over muxes:
2094 reached over Mux(es):
2097 reached over Mux(es):
2102 If you now switch to the new I2C Bus 3 with "i2c dev 3"
2103 u-boot first sends the command to the mux@70 to enable
2104 channel 6, and then the command to the mux@71 to enable
2107 After that, you can use the "normal" i2c commands as
2108 usual to communicate with your I2C devices behind
2111 This option is actually implemented for the bitbanging
2112 algorithm in common/soft_i2c.c and for the Hardware I2C
2113 Bus on the MPC8260. But it should be not so difficult
2114 to add this option to other architectures.
2116 CONFIG_SOFT_I2C_READ_REPEATED_START
2118 defining this will force the i2c_read() function in
2119 the soft_i2c driver to perform an I2C repeated start
2120 between writing the address pointer and reading the
2121 data. If this define is omitted the default behaviour
2122 of doing a stop-start sequence will be used. Most I2C
2123 devices can use either method, but some require one or
2126 - SPI Support: CONFIG_SPI
2128 Enables SPI driver (so far only tested with
2129 SPI EEPROM, also an instance works with Crystal A/D and
2130 D/As on the SACSng board)
2134 Enables the driver for SPI controller on SuperH. Currently
2135 only SH7757 is supported.
2139 Enables extended (16-bit) SPI EEPROM addressing.
2140 (symmetrical to CONFIG_I2C_X)
2144 Enables a software (bit-bang) SPI driver rather than
2145 using hardware support. This is a general purpose
2146 driver that only requires three general I/O port pins
2147 (two outputs, one input) to function. If this is
2148 defined, the board configuration must define several
2149 SPI configuration items (port pins to use, etc). For
2150 an example, see include/configs/sacsng.h.
2154 Enables a hardware SPI driver for general-purpose reads
2155 and writes. As with CONFIG_SOFT_SPI, the board configuration
2156 must define a list of chip-select function pointers.
2157 Currently supported on some MPC8xxx processors. For an
2158 example, see include/configs/mpc8349emds.h.
2162 Enables the driver for the SPI controllers on i.MX and MXC
2163 SoCs. Currently i.MX31/35/51 are supported.
2165 - FPGA Support: CONFIG_FPGA
2167 Enables FPGA subsystem.
2169 CONFIG_FPGA_<vendor>
2171 Enables support for specific chip vendors.
2174 CONFIG_FPGA_<family>
2176 Enables support for FPGA family.
2177 (SPARTAN2, SPARTAN3, VIRTEX2, CYCLONE2, ACEX1K, ACEX)
2181 Specify the number of FPGA devices to support.
2183 CONFIG_SYS_FPGA_PROG_FEEDBACK
2185 Enable printing of hash marks during FPGA configuration.
2187 CONFIG_SYS_FPGA_CHECK_BUSY
2189 Enable checks on FPGA configuration interface busy
2190 status by the configuration function. This option
2191 will require a board or device specific function to
2196 If defined, a function that provides delays in the FPGA
2197 configuration driver.
2199 CONFIG_SYS_FPGA_CHECK_CTRLC
2200 Allow Control-C to interrupt FPGA configuration
2202 CONFIG_SYS_FPGA_CHECK_ERROR
2204 Check for configuration errors during FPGA bitfile
2205 loading. For example, abort during Virtex II
2206 configuration if the INIT_B line goes low (which
2207 indicated a CRC error).
2209 CONFIG_SYS_FPGA_WAIT_INIT
2211 Maximum time to wait for the INIT_B line to deassert
2212 after PROB_B has been deasserted during a Virtex II
2213 FPGA configuration sequence. The default time is 500
2216 CONFIG_SYS_FPGA_WAIT_BUSY
2218 Maximum time to wait for BUSY to deassert during
2219 Virtex II FPGA configuration. The default is 5 ms.
2221 CONFIG_SYS_FPGA_WAIT_CONFIG
2223 Time to wait after FPGA configuration. The default is
2226 - Configuration Management:
2229 If defined, this string will be added to the U-Boot
2230 version information (U_BOOT_VERSION)
2232 - Vendor Parameter Protection:
2234 U-Boot considers the values of the environment
2235 variables "serial#" (Board Serial Number) and
2236 "ethaddr" (Ethernet Address) to be parameters that
2237 are set once by the board vendor / manufacturer, and
2238 protects these variables from casual modification by
2239 the user. Once set, these variables are read-only,
2240 and write or delete attempts are rejected. You can
2241 change this behaviour:
2243 If CONFIG_ENV_OVERWRITE is #defined in your config
2244 file, the write protection for vendor parameters is
2245 completely disabled. Anybody can change or delete
2248 Alternatively, if you #define _both_ CONFIG_ETHADDR
2249 _and_ CONFIG_OVERWRITE_ETHADDR_ONCE, a default
2250 Ethernet address is installed in the environment,
2251 which can be changed exactly ONCE by the user. [The
2252 serial# is unaffected by this, i. e. it remains
2255 The same can be accomplished in a more flexible way
2256 for any variable by configuring the type of access
2257 to allow for those variables in the ".flags" variable
2258 or define CONFIG_ENV_FLAGS_LIST_STATIC.
2263 Define this variable to enable the reservation of
2264 "protected RAM", i. e. RAM which is not overwritten
2265 by U-Boot. Define CONFIG_PRAM to hold the number of
2266 kB you want to reserve for pRAM. You can overwrite
2267 this default value by defining an environment
2268 variable "pram" to the number of kB you want to
2269 reserve. Note that the board info structure will
2270 still show the full amount of RAM. If pRAM is
2271 reserved, a new environment variable "mem" will
2272 automatically be defined to hold the amount of
2273 remaining RAM in a form that can be passed as boot
2274 argument to Linux, for instance like that:
2276 setenv bootargs ... mem=\${mem}
2279 This way you can tell Linux not to use this memory,
2280 either, which results in a memory region that will
2281 not be affected by reboots.
2283 *WARNING* If your board configuration uses automatic
2284 detection of the RAM size, you must make sure that
2285 this memory test is non-destructive. So far, the
2286 following board configurations are known to be
2289 IVMS8, IVML24, SPD8xx, TQM8xxL,
2290 HERMES, IP860, RPXlite, LWMON,
2293 - Access to physical memory region (> 4GB)
2294 Some basic support is provided for operations on memory not
2295 normally accessible to U-Boot - e.g. some architectures
2296 support access to more than 4GB of memory on 32-bit
2297 machines using physical address extension or similar.
2298 Define CONFIG_PHYSMEM to access this basic support, which
2299 currently only supports clearing the memory.
2304 Define this variable to stop the system in case of a
2305 fatal error, so that you have to reset it manually.
2306 This is probably NOT a good idea for an embedded
2307 system where you want the system to reboot
2308 automatically as fast as possible, but it may be
2309 useful during development since you can try to debug
2310 the conditions that lead to the situation.
2312 CONFIG_NET_RETRY_COUNT
2314 This variable defines the number of retries for
2315 network operations like ARP, RARP, TFTP, or BOOTP
2316 before giving up the operation. If not defined, a
2317 default value of 5 is used.
2321 Timeout waiting for an ARP reply in milliseconds.
2325 Timeout in milliseconds used in NFS protocol.
2326 If you encounter "ERROR: Cannot umount" in nfs command,
2327 try longer timeout such as
2328 #define CONFIG_NFS_TIMEOUT 10000UL
2330 - Command Interpreter:
2331 CONFIG_AUTO_COMPLETE
2333 Enable auto completion of commands using TAB.
2335 Note that this feature has NOT been implemented yet
2336 for the "hush" shell.
2339 CONFIG_SYS_HUSH_PARSER
2341 Define this variable to enable the "hush" shell (from
2342 Busybox) as command line interpreter, thus enabling
2343 powerful command line syntax like
2344 if...then...else...fi conditionals or `&&' and '||'
2345 constructs ("shell scripts").
2347 If undefined, you get the old, much simpler behaviour
2348 with a somewhat smaller memory footprint.
2351 CONFIG_SYS_PROMPT_HUSH_PS2
2353 This defines the secondary prompt string, which is
2354 printed when the command interpreter needs more input
2355 to complete a command. Usually "> ".
2359 In the current implementation, the local variables
2360 space and global environment variables space are
2361 separated. Local variables are those you define by
2362 simply typing `name=value'. To access a local
2363 variable later on, you have write `$name' or
2364 `${name}'; to execute the contents of a variable
2365 directly type `$name' at the command prompt.
2367 Global environment variables are those you use
2368 setenv/printenv to work with. To run a command stored
2369 in such a variable, you need to use the run command,
2370 and you must not use the '$' sign to access them.
2372 To store commands and special characters in a
2373 variable, please use double quotation marks
2374 surrounding the whole text of the variable, instead
2375 of the backslashes before semicolons and special
2378 - Commandline Editing and History:
2379 CONFIG_CMDLINE_EDITING
2381 Enable editing and History functions for interactive
2382 commandline input operations
2384 - Default Environment:
2385 CONFIG_EXTRA_ENV_SETTINGS
2387 Define this to contain any number of null terminated
2388 strings (variable = value pairs) that will be part of
2389 the default environment compiled into the boot image.
2391 For example, place something like this in your
2392 board's config file:
2394 #define CONFIG_EXTRA_ENV_SETTINGS \
2398 Warning: This method is based on knowledge about the
2399 internal format how the environment is stored by the
2400 U-Boot code. This is NOT an official, exported
2401 interface! Although it is unlikely that this format
2402 will change soon, there is no guarantee either.
2403 You better know what you are doing here.
2405 Note: overly (ab)use of the default environment is
2406 discouraged. Make sure to check other ways to preset
2407 the environment like the "source" command or the
2410 CONFIG_ENV_VARS_UBOOT_CONFIG
2412 Define this in order to add variables describing the
2413 U-Boot build configuration to the default environment.
2414 These will be named arch, cpu, board, vendor, and soc.
2416 Enabling this option will cause the following to be defined:
2424 CONFIG_ENV_VARS_UBOOT_RUNTIME_CONFIG
2426 Define this in order to add variables describing certain
2427 run-time determined information about the hardware to the
2428 environment. These will be named board_name, board_rev.
2430 CONFIG_DELAY_ENVIRONMENT
2432 Normally the environment is loaded when the board is
2433 intialised so that it is available to U-Boot. This inhibits
2434 that so that the environment is not available until
2435 explicitly loaded later by U-Boot code. With CONFIG_OF_CONTROL
2436 this is instead controlled by the value of
2437 /config/load-environment.
2439 - DataFlash Support:
2440 CONFIG_HAS_DATAFLASH
2442 Defining this option enables DataFlash features and
2443 allows to read/write in Dataflash via the standard
2446 - Serial Flash support
2449 Defining this option enables SPI flash commands
2450 'sf probe/read/write/erase/update'.
2452 Usage requires an initial 'probe' to define the serial
2453 flash parameters, followed by read/write/erase/update
2456 The following defaults may be provided by the platform
2457 to handle the common case when only a single serial
2458 flash is present on the system.
2460 CONFIG_SF_DEFAULT_BUS Bus identifier
2461 CONFIG_SF_DEFAULT_CS Chip-select
2462 CONFIG_SF_DEFAULT_MODE (see include/spi.h)
2463 CONFIG_SF_DEFAULT_SPEED in Hz
2467 Define this option to include a destructive SPI flash
2470 - SystemACE Support:
2473 Adding this option adds support for Xilinx SystemACE
2474 chips attached via some sort of local bus. The address
2475 of the chip must also be defined in the
2476 CONFIG_SYS_SYSTEMACE_BASE macro. For example:
2478 #define CONFIG_SYSTEMACE
2479 #define CONFIG_SYS_SYSTEMACE_BASE 0xf0000000
2481 When SystemACE support is added, the "ace" device type
2482 becomes available to the fat commands, i.e. fatls.
2484 - TFTP Fixed UDP Port:
2487 If this is defined, the environment variable tftpsrcp
2488 is used to supply the TFTP UDP source port value.
2489 If tftpsrcp isn't defined, the normal pseudo-random port
2490 number generator is used.
2492 Also, the environment variable tftpdstp is used to supply
2493 the TFTP UDP destination port value. If tftpdstp isn't
2494 defined, the normal port 69 is used.
2496 The purpose for tftpsrcp is to allow a TFTP server to
2497 blindly start the TFTP transfer using the pre-configured
2498 target IP address and UDP port. This has the effect of
2499 "punching through" the (Windows XP) firewall, allowing
2500 the remainder of the TFTP transfer to proceed normally.
2501 A better solution is to properly configure the firewall,
2502 but sometimes that is not allowed.
2507 This enables a generic 'hash' command which can produce
2508 hashes / digests from a few algorithms (e.g. SHA1, SHA256).
2512 Enable the hash verify command (hash -v). This adds to code
2515 CONFIG_SHA1 - support SHA1 hashing
2516 CONFIG_SHA256 - support SHA256 hashing
2518 Note: There is also a sha1sum command, which should perhaps
2519 be deprecated in favour of 'hash sha1'.
2521 - Show boot progress:
2522 CONFIG_SHOW_BOOT_PROGRESS
2524 Defining this option allows to add some board-
2525 specific code (calling a user-provided function
2526 "show_boot_progress(int)") that enables you to show
2527 the system's boot progress on some display (for
2528 example, some LED's) on your board. At the moment,
2529 the following checkpoints are implemented:
2531 - Detailed boot stage timing
2533 Define this option to get detailed timing of each stage
2534 of the boot process.
2536 CONFIG_BOOTSTAGE_USER_COUNT
2537 This is the number of available user bootstage records.
2538 Each time you call bootstage_mark(BOOTSTAGE_ID_ALLOC, ...)
2539 a new ID will be allocated from this stash. If you exceed
2540 the limit, recording will stop.
2542 CONFIG_BOOTSTAGE_REPORT
2543 Define this to print a report before boot, similar to this:
2545 Timer summary in microseconds:
2548 3,575,678 3,575,678 board_init_f start
2549 3,575,695 17 arch_cpu_init A9
2550 3,575,777 82 arch_cpu_init done
2551 3,659,598 83,821 board_init_r start
2552 3,910,375 250,777 main_loop
2553 29,916,167 26,005,792 bootm_start
2554 30,361,327 445,160 start_kernel
2556 CONFIG_CMD_BOOTSTAGE
2557 Add a 'bootstage' command which supports printing a report
2558 and un/stashing of bootstage data.
2560 CONFIG_BOOTSTAGE_FDT
2561 Stash the bootstage information in the FDT. A root 'bootstage'
2562 node is created with each bootstage id as a child. Each child
2563 has a 'name' property and either 'mark' containing the
2564 mark time in microsecond, or 'accum' containing the
2565 accumulated time for that bootstage id in microseconds.
2570 name = "board_init_f";
2579 Code in the Linux kernel can find this in /proc/devicetree.
2581 Legacy uImage format:
2584 1 common/cmd_bootm.c before attempting to boot an image
2585 -1 common/cmd_bootm.c Image header has bad magic number
2586 2 common/cmd_bootm.c Image header has correct magic number
2587 -2 common/cmd_bootm.c Image header has bad checksum
2588 3 common/cmd_bootm.c Image header has correct checksum
2589 -3 common/cmd_bootm.c Image data has bad checksum
2590 4 common/cmd_bootm.c Image data has correct checksum
2591 -4 common/cmd_bootm.c Image is for unsupported architecture
2592 5 common/cmd_bootm.c Architecture check OK
2593 -5 common/cmd_bootm.c Wrong Image Type (not kernel, multi)
2594 6 common/cmd_bootm.c Image Type check OK
2595 -6 common/cmd_bootm.c gunzip uncompression error
2596 -7 common/cmd_bootm.c Unimplemented compression type
2597 7 common/cmd_bootm.c Uncompression OK
2598 8 common/cmd_bootm.c No uncompress/copy overwrite error
2599 -9 common/cmd_bootm.c Unsupported OS (not Linux, BSD, VxWorks, QNX)
2601 9 common/image.c Start initial ramdisk verification
2602 -10 common/image.c Ramdisk header has bad magic number
2603 -11 common/image.c Ramdisk header has bad checksum
2604 10 common/image.c Ramdisk header is OK
2605 -12 common/image.c Ramdisk data has bad checksum
2606 11 common/image.c Ramdisk data has correct checksum
2607 12 common/image.c Ramdisk verification complete, start loading
2608 -13 common/image.c Wrong Image Type (not PPC Linux ramdisk)
2609 13 common/image.c Start multifile image verification
2610 14 common/image.c No initial ramdisk, no multifile, continue.
2612 15 arch/<arch>/lib/bootm.c All preparation done, transferring control to OS
2614 -30 arch/powerpc/lib/board.c Fatal error, hang the system
2615 -31 post/post.c POST test failed, detected by post_output_backlog()
2616 -32 post/post.c POST test failed, detected by post_run_single()
2618 34 common/cmd_doc.c before loading a Image from a DOC device
2619 -35 common/cmd_doc.c Bad usage of "doc" command
2620 35 common/cmd_doc.c correct usage of "doc" command
2621 -36 common/cmd_doc.c No boot device
2622 36 common/cmd_doc.c correct boot device
2623 -37 common/cmd_doc.c Unknown Chip ID on boot device
2624 37 common/cmd_doc.c correct chip ID found, device available
2625 -38 common/cmd_doc.c Read Error on boot device
2626 38 common/cmd_doc.c reading Image header from DOC device OK
2627 -39 common/cmd_doc.c Image header has bad magic number
2628 39 common/cmd_doc.c Image header has correct magic number
2629 -40 common/cmd_doc.c Error reading Image from DOC device
2630 40 common/cmd_doc.c Image header has correct magic number
2631 41 common/cmd_ide.c before loading a Image from a IDE device
2632 -42 common/cmd_ide.c Bad usage of "ide" command
2633 42 common/cmd_ide.c correct usage of "ide" command
2634 -43 common/cmd_ide.c No boot device
2635 43 common/cmd_ide.c boot device found
2636 -44 common/cmd_ide.c Device not available
2637 44 common/cmd_ide.c Device available
2638 -45 common/cmd_ide.c wrong partition selected
2639 45 common/cmd_ide.c partition selected
2640 -46 common/cmd_ide.c Unknown partition table
2641 46 common/cmd_ide.c valid partition table found
2642 -47 common/cmd_ide.c Invalid partition type
2643 47 common/cmd_ide.c correct partition type
2644 -48 common/cmd_ide.c Error reading Image Header on boot device
2645 48 common/cmd_ide.c reading Image Header from IDE device OK
2646 -49 common/cmd_ide.c Image header has bad magic number
2647 49 common/cmd_ide.c Image header has correct magic number
2648 -50 common/cmd_ide.c Image header has bad checksum
2649 50 common/cmd_ide.c Image header has correct checksum
2650 -51 common/cmd_ide.c Error reading Image from IDE device
2651 51 common/cmd_ide.c reading Image from IDE device OK
2652 52 common/cmd_nand.c before loading a Image from a NAND device
2653 -53 common/cmd_nand.c Bad usage of "nand" command
2654 53 common/cmd_nand.c correct usage of "nand" command
2655 -54 common/cmd_nand.c No boot device
2656 54 common/cmd_nand.c boot device found
2657 -55 common/cmd_nand.c Unknown Chip ID on boot device
2658 55 common/cmd_nand.c correct chip ID found, device available
2659 -56 common/cmd_nand.c Error reading Image Header on boot device
2660 56 common/cmd_nand.c reading Image Header from NAND device OK
2661 -57 common/cmd_nand.c Image header has bad magic number
2662 57 common/cmd_nand.c Image header has correct magic number
2663 -58 common/cmd_nand.c Error reading Image from NAND device
2664 58 common/cmd_nand.c reading Image from NAND device OK
2666 -60 common/env_common.c Environment has a bad CRC, using default
2668 64 net/eth.c starting with Ethernet configuration.
2669 -64 net/eth.c no Ethernet found.
2670 65 net/eth.c Ethernet found.
2672 -80 common/cmd_net.c usage wrong
2673 80 common/cmd_net.c before calling NetLoop()
2674 -81 common/cmd_net.c some error in NetLoop() occurred
2675 81 common/cmd_net.c NetLoop() back without error
2676 -82 common/cmd_net.c size == 0 (File with size 0 loaded)
2677 82 common/cmd_net.c trying automatic boot
2678 83 common/cmd_net.c running "source" command
2679 -83 common/cmd_net.c some error in automatic boot or "source" command
2680 84 common/cmd_net.c end without errors
2685 100 common/cmd_bootm.c Kernel FIT Image has correct format
2686 -100 common/cmd_bootm.c Kernel FIT Image has incorrect format
2687 101 common/cmd_bootm.c No Kernel subimage unit name, using configuration
2688 -101 common/cmd_bootm.c Can't get configuration for kernel subimage
2689 102 common/cmd_bootm.c Kernel unit name specified
2690 -103 common/cmd_bootm.c Can't get kernel subimage node offset
2691 103 common/cmd_bootm.c Found configuration node
2692 104 common/cmd_bootm.c Got kernel subimage node offset
2693 -104 common/cmd_bootm.c Kernel subimage hash verification failed
2694 105 common/cmd_bootm.c Kernel subimage hash verification OK
2695 -105 common/cmd_bootm.c Kernel subimage is for unsupported architecture
2696 106 common/cmd_bootm.c Architecture check OK
2697 -106 common/cmd_bootm.c Kernel subimage has wrong type
2698 107 common/cmd_bootm.c Kernel subimage type OK
2699 -107 common/cmd_bootm.c Can't get kernel subimage data/size
2700 108 common/cmd_bootm.c Got kernel subimage data/size
2701 -108 common/cmd_bootm.c Wrong image type (not legacy, FIT)
2702 -109 common/cmd_bootm.c Can't get kernel subimage type
2703 -110 common/cmd_bootm.c Can't get kernel subimage comp
2704 -111 common/cmd_bootm.c Can't get kernel subimage os
2705 -112 common/cmd_bootm.c Can't get kernel subimage load address
2706 -113 common/cmd_bootm.c Image uncompress/copy overwrite error
2708 120 common/image.c Start initial ramdisk verification
2709 -120 common/image.c Ramdisk FIT image has incorrect format
2710 121 common/image.c Ramdisk FIT image has correct format
2711 122 common/image.c No ramdisk subimage unit name, using configuration
2712 -122 common/image.c Can't get configuration for ramdisk subimage
2713 123 common/image.c Ramdisk unit name specified
2714 -124 common/image.c Can't get ramdisk subimage node offset
2715 125 common/image.c Got ramdisk subimage node offset
2716 -125 common/image.c Ramdisk subimage hash verification failed
2717 126 common/image.c Ramdisk subimage hash verification OK
2718 -126 common/image.c Ramdisk subimage for unsupported architecture
2719 127 common/image.c Architecture check OK
2720 -127 common/image.c Can't get ramdisk subimage data/size
2721 128 common/image.c Got ramdisk subimage data/size
2722 129 common/image.c Can't get ramdisk load address
2723 -129 common/image.c Got ramdisk load address
2725 -130 common/cmd_doc.c Incorrect FIT image format
2726 131 common/cmd_doc.c FIT image format OK
2728 -140 common/cmd_ide.c Incorrect FIT image format
2729 141 common/cmd_ide.c FIT image format OK
2731 -150 common/cmd_nand.c Incorrect FIT image format
2732 151 common/cmd_nand.c FIT image format OK
2734 - FIT image support:
2736 Enable support for the FIT uImage format.
2738 CONFIG_FIT_BEST_MATCH
2739 When no configuration is explicitly selected, default to the
2740 one whose fdt's compatibility field best matches that of
2741 U-Boot itself. A match is considered "best" if it matches the
2742 most specific compatibility entry of U-Boot's fdt's root node.
2743 The order of entries in the configuration's fdt is ignored.
2745 - Standalone program support:
2746 CONFIG_STANDALONE_LOAD_ADDR
2748 This option defines a board specific value for the
2749 address where standalone program gets loaded, thus
2750 overwriting the architecture dependent default
2753 - Frame Buffer Address:
2756 Define CONFIG_FB_ADDR if you want to use specific
2757 address for frame buffer. This is typically the case
2758 when using a graphics controller has separate video
2759 memory. U-Boot will then place the frame buffer at
2760 the given address instead of dynamically reserving it
2761 in system RAM by calling lcd_setmem(), which grabs
2762 the memory for the frame buffer depending on the
2763 configured panel size.
2765 Please see board_init_f function.
2767 - Automatic software updates via TFTP server
2769 CONFIG_UPDATE_TFTP_CNT_MAX
2770 CONFIG_UPDATE_TFTP_MSEC_MAX
2772 These options enable and control the auto-update feature;
2773 for a more detailed description refer to doc/README.update.
2775 - MTD Support (mtdparts command, UBI support)
2778 Adds the MTD device infrastructure from the Linux kernel.
2779 Needed for mtdparts command support.
2781 CONFIG_MTD_PARTITIONS
2783 Adds the MTD partitioning infrastructure from the Linux
2784 kernel. Needed for UBI support.
2788 Enable building of SPL globally.
2791 LDSCRIPT for linking the SPL binary.
2794 Maximum binary size (text, data and rodata) of the SPL binary.
2796 CONFIG_SPL_TEXT_BASE
2797 TEXT_BASE for linking the SPL binary.
2799 CONFIG_SPL_RELOC_TEXT_BASE
2800 Address to relocate to. If unspecified, this is equal to
2801 CONFIG_SPL_TEXT_BASE (i.e. no relocation is done).
2803 CONFIG_SPL_BSS_START_ADDR
2804 Link address for the BSS within the SPL binary.
2806 CONFIG_SPL_BSS_MAX_SIZE
2807 Maximum binary size of the BSS section of the SPL binary.
2810 Adress of the start of the stack SPL will use
2812 CONFIG_SPL_RELOC_STACK
2813 Adress of the start of the stack SPL will use after
2814 relocation. If unspecified, this is equal to
2817 CONFIG_SYS_SPL_MALLOC_START
2818 Starting address of the malloc pool used in SPL.
2820 CONFIG_SYS_SPL_MALLOC_SIZE
2821 The size of the malloc pool used in SPL.
2823 CONFIG_SPL_FRAMEWORK
2824 Enable the SPL framework under common/. This framework
2825 supports MMC, NAND and YMODEM loading of U-Boot and NAND
2826 NAND loading of the Linux Kernel.
2828 CONFIG_SPL_DISPLAY_PRINT
2829 For ARM, enable an optional function to print more information
2830 about the running system.
2832 CONFIG_SPL_INIT_MINIMAL
2833 Arch init code should be built for a very small image
2835 CONFIG_SPL_LIBCOMMON_SUPPORT
2836 Support for common/libcommon.o in SPL binary
2838 CONFIG_SPL_LIBDISK_SUPPORT
2839 Support for disk/libdisk.o in SPL binary
2841 CONFIG_SPL_I2C_SUPPORT
2842 Support for drivers/i2c/libi2c.o in SPL binary
2844 CONFIG_SPL_GPIO_SUPPORT
2845 Support for drivers/gpio/libgpio.o in SPL binary
2847 CONFIG_SPL_MMC_SUPPORT
2848 Support for drivers/mmc/libmmc.o in SPL binary
2850 CONFIG_SYS_MMCSD_RAW_MODE_U_BOOT_SECTOR,
2851 CONFIG_SYS_U_BOOT_MAX_SIZE_SECTORS,
2852 CONFIG_SYS_MMC_SD_FAT_BOOT_PARTITION
2853 Address, size and partition on the MMC to load U-Boot from
2854 when the MMC is being used in raw mode.
2856 CONFIG_SPL_FAT_SUPPORT
2857 Support for fs/fat/libfat.o in SPL binary
2859 CONFIG_SPL_FAT_LOAD_PAYLOAD_NAME
2860 Filename to read to load U-Boot when reading from FAT
2862 CONFIG_SPL_MPC83XX_WAIT_FOR_NAND
2863 Set this for NAND SPL on PPC mpc83xx targets, so that
2864 start.S waits for the rest of the SPL to load before
2865 continuing (the hardware starts execution after just
2866 loading the first page rather than the full 4K).
2868 CONFIG_SPL_NAND_BASE
2869 Include nand_base.c in the SPL. Requires
2870 CONFIG_SPL_NAND_DRIVERS.
2872 CONFIG_SPL_NAND_DRIVERS
2873 SPL uses normal NAND drivers, not minimal drivers.
2876 Include standard software ECC in the SPL
2878 CONFIG_SPL_NAND_SIMPLE
2879 Support for NAND boot using simple NAND drivers that
2880 expose the cmd_ctrl() interface.
2882 CONFIG_SYS_NAND_5_ADDR_CYCLE, CONFIG_SYS_NAND_PAGE_COUNT,
2883 CONFIG_SYS_NAND_PAGE_SIZE, CONFIG_SYS_NAND_OOBSIZE,
2884 CONFIG_SYS_NAND_BLOCK_SIZE, CONFIG_SYS_NAND_BAD_BLOCK_POS,
2885 CONFIG_SYS_NAND_ECCPOS, CONFIG_SYS_NAND_ECCSIZE,
2886 CONFIG_SYS_NAND_ECCBYTES
2887 Defines the size and behavior of the NAND that SPL uses
2890 CONFIG_SYS_NAND_U_BOOT_OFFS
2891 Location in NAND to read U-Boot from
2893 CONFIG_SYS_NAND_U_BOOT_DST
2894 Location in memory to load U-Boot to
2896 CONFIG_SYS_NAND_U_BOOT_SIZE
2897 Size of image to load
2899 CONFIG_SYS_NAND_U_BOOT_START
2900 Entry point in loaded image to jump to
2902 CONFIG_SYS_NAND_HW_ECC_OOBFIRST
2903 Define this if you need to first read the OOB and then the
2904 data. This is used for example on davinci plattforms.
2906 CONFIG_SPL_OMAP3_ID_NAND
2907 Support for an OMAP3-specific set of functions to return the
2908 ID and MFR of the first attached NAND chip, if present.
2910 CONFIG_SPL_SERIAL_SUPPORT
2911 Support for drivers/serial/libserial.o in SPL binary
2913 CONFIG_SPL_SPI_FLASH_SUPPORT
2914 Support for drivers/mtd/spi/libspi_flash.o in SPL binary
2916 CONFIG_SPL_SPI_SUPPORT
2917 Support for drivers/spi/libspi.o in SPL binary
2919 CONFIG_SPL_RAM_DEVICE
2920 Support for running image already present in ram, in SPL binary
2922 CONFIG_SPL_LIBGENERIC_SUPPORT
2923 Support for lib/libgeneric.o in SPL binary
2926 Linker address to which the SPL should be padded before
2927 appending the SPL payload.
2930 Final target image containing SPL and payload. Some SPLs
2931 use an arch-specific makefile fragment instead, for
2932 example if more than one image needs to be produced.
2937 [so far only for SMDK2400 boards]
2939 - Modem support enable:
2940 CONFIG_MODEM_SUPPORT
2942 - RTS/CTS Flow control enable:
2945 - Modem debug support:
2946 CONFIG_MODEM_SUPPORT_DEBUG
2948 Enables debugging stuff (char screen[1024], dbg())
2949 for modem support. Useful only with BDI2000.
2951 - Interrupt support (PPC):
2953 There are common interrupt_init() and timer_interrupt()
2954 for all PPC archs. interrupt_init() calls interrupt_init_cpu()
2955 for CPU specific initialization. interrupt_init_cpu()
2956 should set decrementer_count to appropriate value. If
2957 CPU resets decrementer automatically after interrupt
2958 (ppc4xx) it should set decrementer_count to zero.
2959 timer_interrupt() calls timer_interrupt_cpu() for CPU
2960 specific handling. If board has watchdog / status_led
2961 / other_activity_monitor it works automatically from
2962 general timer_interrupt().
2966 In the target system modem support is enabled when a
2967 specific key (key combination) is pressed during
2968 power-on. Otherwise U-Boot will boot normally
2969 (autoboot). The key_pressed() function is called from
2970 board_init(). Currently key_pressed() is a dummy
2971 function, returning 1 and thus enabling modem
2974 If there are no modem init strings in the
2975 environment, U-Boot proceed to autoboot; the
2976 previous output (banner, info printfs) will be
2979 See also: doc/README.Modem
2981 Board initialization settings:
2982 ------------------------------
2984 During Initialization u-boot calls a number of board specific functions
2985 to allow the preparation of board specific prerequisites, e.g. pin setup
2986 before drivers are initialized. To enable these callbacks the
2987 following configuration macros have to be defined. Currently this is
2988 architecture specific, so please check arch/your_architecture/lib/board.c
2989 typically in board_init_f() and board_init_r().
2991 - CONFIG_BOARD_EARLY_INIT_F: Call board_early_init_f()
2992 - CONFIG_BOARD_EARLY_INIT_R: Call board_early_init_r()
2993 - CONFIG_BOARD_LATE_INIT: Call board_late_init()
2994 - CONFIG_BOARD_POSTCLK_INIT: Call board_postclk_init()
2996 Configuration Settings:
2997 -----------------------
2999 - CONFIG_SYS_LONGHELP: Defined when you want long help messages included;
3000 undefine this when you're short of memory.
3002 - CONFIG_SYS_HELP_CMD_WIDTH: Defined when you want to override the default
3003 width of the commands listed in the 'help' command output.
3005 - CONFIG_SYS_PROMPT: This is what U-Boot prints on the console to
3006 prompt for user input.
3008 - CONFIG_SYS_CBSIZE: Buffer size for input from the Console
3010 - CONFIG_SYS_PBSIZE: Buffer size for Console output
3012 - CONFIG_SYS_MAXARGS: max. Number of arguments accepted for monitor commands
3014 - CONFIG_SYS_BARGSIZE: Buffer size for Boot Arguments which are passed to
3015 the application (usually a Linux kernel) when it is
3018 - CONFIG_SYS_BAUDRATE_TABLE:
3019 List of legal baudrate settings for this board.
3021 - CONFIG_SYS_CONSOLE_INFO_QUIET
3022 Suppress display of console information at boot.
3024 - CONFIG_SYS_CONSOLE_IS_IN_ENV
3025 If the board specific function
3026 extern int overwrite_console (void);
3027 returns 1, the stdin, stderr and stdout are switched to the
3028 serial port, else the settings in the environment are used.
3030 - CONFIG_SYS_CONSOLE_OVERWRITE_ROUTINE
3031 Enable the call to overwrite_console().
3033 - CONFIG_SYS_CONSOLE_ENV_OVERWRITE
3034 Enable overwrite of previous console environment settings.
3036 - CONFIG_SYS_MEMTEST_START, CONFIG_SYS_MEMTEST_END:
3037 Begin and End addresses of the area used by the
3040 - CONFIG_SYS_ALT_MEMTEST:
3041 Enable an alternate, more extensive memory test.
3043 - CONFIG_SYS_MEMTEST_SCRATCH:
3044 Scratch address used by the alternate memory test
3045 You only need to set this if address zero isn't writeable
3047 - CONFIG_SYS_MEM_TOP_HIDE (PPC only):
3048 If CONFIG_SYS_MEM_TOP_HIDE is defined in the board config header,
3049 this specified memory area will get subtracted from the top
3050 (end) of RAM and won't get "touched" at all by U-Boot. By
3051 fixing up gd->ram_size the Linux kernel should gets passed
3052 the now "corrected" memory size and won't touch it either.
3053 This should work for arch/ppc and arch/powerpc. Only Linux
3054 board ports in arch/powerpc with bootwrapper support that
3055 recalculate the memory size from the SDRAM controller setup
3056 will have to get fixed in Linux additionally.
3058 This option can be used as a workaround for the 440EPx/GRx
3059 CHIP 11 errata where the last 256 bytes in SDRAM shouldn't
3062 WARNING: Please make sure that this value is a multiple of
3063 the Linux page size (normally 4k). If this is not the case,
3064 then the end address of the Linux memory will be located at a
3065 non page size aligned address and this could cause major
3068 - CONFIG_SYS_LOADS_BAUD_CHANGE:
3069 Enable temporary baudrate change while serial download
3071 - CONFIG_SYS_SDRAM_BASE:
3072 Physical start address of SDRAM. _Must_ be 0 here.
3074 - CONFIG_SYS_MBIO_BASE:
3075 Physical start address of Motherboard I/O (if using a
3078 - CONFIG_SYS_FLASH_BASE:
3079 Physical start address of Flash memory.
3081 - CONFIG_SYS_MONITOR_BASE:
3082 Physical start address of boot monitor code (set by
3083 make config files to be same as the text base address
3084 (CONFIG_SYS_TEXT_BASE) used when linking) - same as
3085 CONFIG_SYS_FLASH_BASE when booting from flash.
3087 - CONFIG_SYS_MONITOR_LEN:
3088 Size of memory reserved for monitor code, used to
3089 determine _at_compile_time_ (!) if the environment is
3090 embedded within the U-Boot image, or in a separate
3093 - CONFIG_SYS_MALLOC_LEN:
3094 Size of DRAM reserved for malloc() use.
3096 - CONFIG_SYS_BOOTM_LEN:
3097 Normally compressed uImages are limited to an
3098 uncompressed size of 8 MBytes. If this is not enough,
3099 you can define CONFIG_SYS_BOOTM_LEN in your board config file
3100 to adjust this setting to your needs.
3102 - CONFIG_SYS_BOOTMAPSZ:
3103 Maximum size of memory mapped by the startup code of
3104 the Linux kernel; all data that must be processed by
3105 the Linux kernel (bd_info, boot arguments, FDT blob if
3106 used) must be put below this limit, unless "bootm_low"
3107 enviroment variable is defined and non-zero. In such case
3108 all data for the Linux kernel must be between "bootm_low"
3109 and "bootm_low" + CONFIG_SYS_BOOTMAPSZ. The environment
3110 variable "bootm_mapsize" will override the value of
3111 CONFIG_SYS_BOOTMAPSZ. If CONFIG_SYS_BOOTMAPSZ is undefined,
3112 then the value in "bootm_size" will be used instead.
3114 - CONFIG_SYS_BOOT_RAMDISK_HIGH:
3115 Enable initrd_high functionality. If defined then the
3116 initrd_high feature is enabled and the bootm ramdisk subcommand
3119 - CONFIG_SYS_BOOT_GET_CMDLINE:
3120 Enables allocating and saving kernel cmdline in space between
3121 "bootm_low" and "bootm_low" + BOOTMAPSZ.
3123 - CONFIG_SYS_BOOT_GET_KBD:
3124 Enables allocating and saving a kernel copy of the bd_info in
3125 space between "bootm_low" and "bootm_low" + BOOTMAPSZ.
3127 - CONFIG_SYS_MAX_FLASH_BANKS:
3128 Max number of Flash memory banks
3130 - CONFIG_SYS_MAX_FLASH_SECT:
3131 Max number of sectors on a Flash chip
3133 - CONFIG_SYS_FLASH_ERASE_TOUT:
3134 Timeout for Flash erase operations (in ms)
3136 - CONFIG_SYS_FLASH_WRITE_TOUT:
3137 Timeout for Flash write operations (in ms)
3139 - CONFIG_SYS_FLASH_LOCK_TOUT
3140 Timeout for Flash set sector lock bit operation (in ms)
3142 - CONFIG_SYS_FLASH_UNLOCK_TOUT
3143 Timeout for Flash clear lock bits operation (in ms)
3145 - CONFIG_SYS_FLASH_PROTECTION
3146 If defined, hardware flash sectors protection is used
3147 instead of U-Boot software protection.
3149 - CONFIG_SYS_DIRECT_FLASH_TFTP:
3151 Enable TFTP transfers directly to flash memory;
3152 without this option such a download has to be
3153 performed in two steps: (1) download to RAM, and (2)
3154 copy from RAM to flash.
3156 The two-step approach is usually more reliable, since
3157 you can check if the download worked before you erase
3158 the flash, but in some situations (when system RAM is
3159 too limited to allow for a temporary copy of the
3160 downloaded image) this option may be very useful.
3162 - CONFIG_SYS_FLASH_CFI:
3163 Define if the flash driver uses extra elements in the
3164 common flash structure for storing flash geometry.
3166 - CONFIG_FLASH_CFI_DRIVER
3167 This option also enables the building of the cfi_flash driver
3168 in the drivers directory
3170 - CONFIG_FLASH_CFI_MTD
3171 This option enables the building of the cfi_mtd driver
3172 in the drivers directory. The driver exports CFI flash
3175 - CONFIG_SYS_FLASH_USE_BUFFER_WRITE
3176 Use buffered writes to flash.
3178 - CONFIG_FLASH_SPANSION_S29WS_N
3179 s29ws-n MirrorBit flash has non-standard addresses for buffered
3182 - CONFIG_SYS_FLASH_QUIET_TEST
3183 If this option is defined, the common CFI flash doesn't
3184 print it's warning upon not recognized FLASH banks. This
3185 is useful, if some of the configured banks are only
3186 optionally available.
3188 - CONFIG_FLASH_SHOW_PROGRESS
3189 If defined (must be an integer), print out countdown
3190 digits and dots. Recommended value: 45 (9..1) for 80
3191 column displays, 15 (3..1) for 40 column displays.
3193 - CONFIG_SYS_RX_ETH_BUFFER:
3194 Defines the number of Ethernet receive buffers. On some
3195 Ethernet controllers it is recommended to set this value
3196 to 8 or even higher (EEPRO100 or 405 EMAC), since all
3197 buffers can be full shortly after enabling the interface
3198 on high Ethernet traffic.
3199 Defaults to 4 if not defined.
3201 - CONFIG_ENV_MAX_ENTRIES
3203 Maximum number of entries in the hash table that is used
3204 internally to store the environment settings. The default
3205 setting is supposed to be generous and should work in most
3206 cases. This setting can be used to tune behaviour; see
3207 lib/hashtable.c for details.
3209 - CONFIG_ENV_FLAGS_LIST_DEFAULT
3210 - CONFIG_ENV_FLAGS_LIST_STATIC
3211 Enable validation of the values given to enviroment variables when
3212 calling env set. Variables can be restricted to only decimal,
3213 hexadecimal, or boolean. If CONFIG_CMD_NET is also defined,
3214 the variables can also be restricted to IP address or MAC address.
3216 The format of the list is:
3217 type_attribute = [s|d|x|b|i|m]
3218 access_atribute = [a|r|o|c]
3219 attributes = type_attribute[access_atribute]
3220 entry = variable_name[:attributes]
3223 The type attributes are:
3224 s - String (default)
3227 b - Boolean ([1yYtT|0nNfF])
3231 The access attributes are:
3237 - CONFIG_ENV_FLAGS_LIST_DEFAULT
3238 Define this to a list (string) to define the ".flags"
3239 envirnoment variable in the default or embedded environment.
3241 - CONFIG_ENV_FLAGS_LIST_STATIC
3242 Define this to a list (string) to define validation that
3243 should be done if an entry is not found in the ".flags"
3244 environment variable. To override a setting in the static
3245 list, simply add an entry for the same variable name to the
3248 - CONFIG_ENV_ACCESS_IGNORE_FORCE
3249 If defined, don't allow the -f switch to env set override variable
3252 - CONFIG_SYS_GENERIC_BOARD
3253 This selects the architecture-generic board system instead of the
3254 architecture-specific board files. It is intended to move boards
3255 to this new framework over time. Defining this will disable the
3256 arch/foo/lib/board.c file and use common/board_f.c and
3257 common/board_r.c instead. To use this option your architecture
3258 must support it (i.e. must define __HAVE_ARCH_GENERIC_BOARD in
3259 its config.mk file). If you find problems enabling this option on
3260 your board please report the problem and send patches!
3262 - CONFIG_SYS_SYM_OFFSETS
3263 This is set by architectures that use offsets for link symbols
3264 instead of absolute values. So bss_start is obtained using an
3265 offset _bss_start_ofs from CONFIG_SYS_TEXT_BASE, rather than
3266 directly. You should not need to touch this setting.
3269 The following definitions that deal with the placement and management
3270 of environment data (variable area); in general, we support the
3271 following configurations:
3273 - CONFIG_BUILD_ENVCRC:
3275 Builds up envcrc with the target environment so that external utils
3276 may easily extract it and embed it in final U-Boot images.
3278 - CONFIG_ENV_IS_IN_FLASH:
3280 Define this if the environment is in flash memory.
3282 a) The environment occupies one whole flash sector, which is
3283 "embedded" in the text segment with the U-Boot code. This
3284 happens usually with "bottom boot sector" or "top boot
3285 sector" type flash chips, which have several smaller
3286 sectors at the start or the end. For instance, such a
3287 layout can have sector sizes of 8, 2x4, 16, Nx32 kB. In
3288 such a case you would place the environment in one of the
3289 4 kB sectors - with U-Boot code before and after it. With
3290 "top boot sector" type flash chips, you would put the
3291 environment in one of the last sectors, leaving a gap
3292 between U-Boot and the environment.
3294 - CONFIG_ENV_OFFSET:
3296 Offset of environment data (variable area) to the
3297 beginning of flash memory; for instance, with bottom boot
3298 type flash chips the second sector can be used: the offset
3299 for this sector is given here.
3301 CONFIG_ENV_OFFSET is used relative to CONFIG_SYS_FLASH_BASE.
3305 This is just another way to specify the start address of
3306 the flash sector containing the environment (instead of
3309 - CONFIG_ENV_SECT_SIZE:
3311 Size of the sector containing the environment.
3314 b) Sometimes flash chips have few, equal sized, BIG sectors.
3315 In such a case you don't want to spend a whole sector for
3320 If you use this in combination with CONFIG_ENV_IS_IN_FLASH
3321 and CONFIG_ENV_SECT_SIZE, you can specify to use only a part
3322 of this flash sector for the environment. This saves
3323 memory for the RAM copy of the environment.
3325 It may also save flash memory if you decide to use this
3326 when your environment is "embedded" within U-Boot code,
3327 since then the remainder of the flash sector could be used
3328 for U-Boot code. It should be pointed out that this is
3329 STRONGLY DISCOURAGED from a robustness point of view:
3330 updating the environment in flash makes it always
3331 necessary to erase the WHOLE sector. If something goes
3332 wrong before the contents has been restored from a copy in
3333 RAM, your target system will be dead.
3335 - CONFIG_ENV_ADDR_REDUND
3336 CONFIG_ENV_SIZE_REDUND
3338 These settings describe a second storage area used to hold
3339 a redundant copy of the environment data, so that there is
3340 a valid backup copy in case there is a power failure during
3341 a "saveenv" operation.
3343 BE CAREFUL! Any changes to the flash layout, and some changes to the
3344 source code will make it necessary to adapt <board>/u-boot.lds*
3348 - CONFIG_ENV_IS_IN_NVRAM:
3350 Define this if you have some non-volatile memory device
3351 (NVRAM, battery buffered SRAM) which you want to use for the
3357 These two #defines are used to determine the memory area you
3358 want to use for environment. It is assumed that this memory
3359 can just be read and written to, without any special
3362 BE CAREFUL! The first access to the environment happens quite early
3363 in U-Boot initalization (when we try to get the setting of for the
3364 console baudrate). You *MUST* have mapped your NVRAM area then, or
3367 Please note that even with NVRAM we still use a copy of the
3368 environment in RAM: we could work on NVRAM directly, but we want to
3369 keep settings there always unmodified except somebody uses "saveenv"
3370 to save the current settings.
3373 - CONFIG_ENV_IS_IN_EEPROM:
3375 Use this if you have an EEPROM or similar serial access
3376 device and a driver for it.
3378 - CONFIG_ENV_OFFSET:
3381 These two #defines specify the offset and size of the
3382 environment area within the total memory of your EEPROM.
3384 - CONFIG_SYS_I2C_EEPROM_ADDR:
3385 If defined, specified the chip address of the EEPROM device.
3386 The default address is zero.
3388 - CONFIG_SYS_EEPROM_PAGE_WRITE_BITS:
3389 If defined, the number of bits used to address bytes in a
3390 single page in the EEPROM device. A 64 byte page, for example
3391 would require six bits.
3393 - CONFIG_SYS_EEPROM_PAGE_WRITE_DELAY_MS:
3394 If defined, the number of milliseconds to delay between
3395 page writes. The default is zero milliseconds.
3397 - CONFIG_SYS_I2C_EEPROM_ADDR_LEN:
3398 The length in bytes of the EEPROM memory array address. Note
3399 that this is NOT the chip address length!
3401 - CONFIG_SYS_I2C_EEPROM_ADDR_OVERFLOW:
3402 EEPROM chips that implement "address overflow" are ones
3403 like Catalyst 24WC04/08/16 which has 9/10/11 bits of
3404 address and the extra bits end up in the "chip address" bit
3405 slots. This makes a 24WC08 (1Kbyte) chip look like four 256
3408 Note that we consider the length of the address field to
3409 still be one byte because the extra address bits are hidden
3410 in the chip address.
3412 - CONFIG_SYS_EEPROM_SIZE:
3413 The size in bytes of the EEPROM device.
3415 - CONFIG_ENV_EEPROM_IS_ON_I2C
3416 define this, if you have I2C and SPI activated, and your
3417 EEPROM, which holds the environment, is on the I2C bus.
3419 - CONFIG_I2C_ENV_EEPROM_BUS
3420 if you have an Environment on an EEPROM reached over
3421 I2C muxes, you can define here, how to reach this
3422 EEPROM. For example:
3424 #define CONFIG_I2C_ENV_EEPROM_BUS "pca9547:70:d\0"
3426 EEPROM which holds the environment, is reached over
3427 a pca9547 i2c mux with address 0x70, channel 3.
3429 - CONFIG_ENV_IS_IN_DATAFLASH:
3431 Define this if you have a DataFlash memory device which you
3432 want to use for the environment.
3434 - CONFIG_ENV_OFFSET:
3438 These three #defines specify the offset and size of the
3439 environment area within the total memory of your DataFlash placed
3440 at the specified address.
3442 - CONFIG_ENV_IS_IN_REMOTE:
3444 Define this if you have a remote memory space which you
3445 want to use for the local device's environment.
3450 These two #defines specify the address and size of the
3451 environment area within the remote memory space. The
3452 local device can get the environment from remote memory
3453 space by SRIO or PCIE links.
3455 BE CAREFUL! For some special cases, the local device can not use
3456 "saveenv" command. For example, the local device will get the
3457 environment stored in a remote NOR flash by SRIO or PCIE link,
3458 but it can not erase, write this NOR flash by SRIO or PCIE interface.
3460 - CONFIG_ENV_IS_IN_NAND:
3462 Define this if you have a NAND device which you want to use
3463 for the environment.
3465 - CONFIG_ENV_OFFSET:
3468 These two #defines specify the offset and size of the environment
3469 area within the first NAND device. CONFIG_ENV_OFFSET must be
3470 aligned to an erase block boundary.
3472 - CONFIG_ENV_OFFSET_REDUND (optional):
3474 This setting describes a second storage area of CONFIG_ENV_SIZE
3475 size used to hold a redundant copy of the environment data, so
3476 that there is a valid backup copy in case there is a power failure
3477 during a "saveenv" operation. CONFIG_ENV_OFFSET_RENDUND must be
3478 aligned to an erase block boundary.
3480 - CONFIG_ENV_RANGE (optional):
3482 Specifies the length of the region in which the environment
3483 can be written. This should be a multiple of the NAND device's
3484 block size. Specifying a range with more erase blocks than
3485 are needed to hold CONFIG_ENV_SIZE allows bad blocks within
3486 the range to be avoided.
3488 - CONFIG_ENV_OFFSET_OOB (optional):
3490 Enables support for dynamically retrieving the offset of the
3491 environment from block zero's out-of-band data. The
3492 "nand env.oob" command can be used to record this offset.
3493 Currently, CONFIG_ENV_OFFSET_REDUND is not supported when
3494 using CONFIG_ENV_OFFSET_OOB.
3496 - CONFIG_NAND_ENV_DST
3498 Defines address in RAM to which the nand_spl code should copy the
3499 environment. If redundant environment is used, it will be copied to
3500 CONFIG_NAND_ENV_DST + CONFIG_ENV_SIZE.
3502 - CONFIG_SYS_SPI_INIT_OFFSET
3504 Defines offset to the initial SPI buffer area in DPRAM. The
3505 area is used at an early stage (ROM part) if the environment
3506 is configured to reside in the SPI EEPROM: We need a 520 byte
3507 scratch DPRAM area. It is used between the two initialization
3508 calls (spi_init_f() and spi_init_r()). A value of 0xB00 seems
3509 to be a good choice since it makes it far enough from the
3510 start of the data area as well as from the stack pointer.
3512 Please note that the environment is read-only until the monitor
3513 has been relocated to RAM and a RAM copy of the environment has been
3514 created; also, when using EEPROM you will have to use getenv_f()
3515 until then to read environment variables.
3517 The environment is protected by a CRC32 checksum. Before the monitor
3518 is relocated into RAM, as a result of a bad CRC you will be working
3519 with the compiled-in default environment - *silently*!!! [This is
3520 necessary, because the first environment variable we need is the
3521 "baudrate" setting for the console - if we have a bad CRC, we don't
3522 have any device yet where we could complain.]
3524 Note: once the monitor has been relocated, then it will complain if
3525 the default environment is used; a new CRC is computed as soon as you
3526 use the "saveenv" command to store a valid environment.
3528 - CONFIG_SYS_FAULT_ECHO_LINK_DOWN:
3529 Echo the inverted Ethernet link state to the fault LED.
3531 Note: If this option is active, then CONFIG_SYS_FAULT_MII_ADDR
3532 also needs to be defined.
3534 - CONFIG_SYS_FAULT_MII_ADDR:
3535 MII address of the PHY to check for the Ethernet link state.
3537 - CONFIG_NS16550_MIN_FUNCTIONS:
3538 Define this if you desire to only have use of the NS16550_init
3539 and NS16550_putc functions for the serial driver located at
3540 drivers/serial/ns16550.c. This option is useful for saving
3541 space for already greatly restricted images, including but not
3542 limited to NAND_SPL configurations.
3544 - CONFIG_DISPLAY_BOARDINFO
3545 Display information about the board that U-Boot is running on
3546 when U-Boot starts up. The board function checkboard() is called
3549 - CONFIG_DISPLAY_BOARDINFO_LATE
3550 Similar to the previous option, but display this information
3551 later, once stdio is running and output goes to the LCD, if
3554 Low Level (hardware related) configuration options:
3555 ---------------------------------------------------
3557 - CONFIG_SYS_CACHELINE_SIZE:
3558 Cache Line Size of the CPU.
3560 - CONFIG_SYS_DEFAULT_IMMR:
3561 Default address of the IMMR after system reset.
3563 Needed on some 8260 systems (MPC8260ADS, PQ2FADS-ZU,
3564 and RPXsuper) to be able to adjust the position of
3565 the IMMR register after a reset.
3567 - CONFIG_SYS_CCSRBAR_DEFAULT:
3568 Default (power-on reset) physical address of CCSR on Freescale
3571 - CONFIG_SYS_CCSRBAR:
3572 Virtual address of CCSR. On a 32-bit build, this is typically
3573 the same value as CONFIG_SYS_CCSRBAR_DEFAULT.
3575 CONFIG_SYS_DEFAULT_IMMR must also be set to this value,
3576 for cross-platform code that uses that macro instead.
3578 - CONFIG_SYS_CCSRBAR_PHYS:
3579 Physical address of CCSR. CCSR can be relocated to a new
3580 physical address, if desired. In this case, this macro should
3581 be set to that address. Otherwise, it should be set to the
3582 same value as CONFIG_SYS_CCSRBAR_DEFAULT. For example, CCSR
3583 is typically relocated on 36-bit builds. It is recommended
3584 that this macro be defined via the _HIGH and _LOW macros:
3586 #define CONFIG_SYS_CCSRBAR_PHYS ((CONFIG_SYS_CCSRBAR_PHYS_HIGH
3587 * 1ull) << 32 | CONFIG_SYS_CCSRBAR_PHYS_LOW)
3589 - CONFIG_SYS_CCSRBAR_PHYS_HIGH:
3590 Bits 33-36 of CONFIG_SYS_CCSRBAR_PHYS. This value is typically
3591 either 0 (32-bit build) or 0xF (36-bit build). This macro is
3592 used in assembly code, so it must not contain typecasts or
3593 integer size suffixes (e.g. "ULL").
3595 - CONFIG_SYS_CCSRBAR_PHYS_LOW:
3596 Lower 32-bits of CONFIG_SYS_CCSRBAR_PHYS. This macro is
3597 used in assembly code, so it must not contain typecasts or
3598 integer size suffixes (e.g. "ULL").
3600 - CONFIG_SYS_CCSR_DO_NOT_RELOCATE:
3601 If this macro is defined, then CONFIG_SYS_CCSRBAR_PHYS will be
3602 forced to a value that ensures that CCSR is not relocated.
3604 - Floppy Disk Support:
3605 CONFIG_SYS_FDC_DRIVE_NUMBER
3607 the default drive number (default value 0)
3609 CONFIG_SYS_ISA_IO_STRIDE
3611 defines the spacing between FDC chipset registers
3614 CONFIG_SYS_ISA_IO_OFFSET
3616 defines the offset of register from address. It
3617 depends on which part of the data bus is connected to
3618 the FDC chipset. (default value 0)
3620 If CONFIG_SYS_ISA_IO_STRIDE CONFIG_SYS_ISA_IO_OFFSET and
3621 CONFIG_SYS_FDC_DRIVE_NUMBER are undefined, they take their
3624 if CONFIG_SYS_FDC_HW_INIT is defined, then the function
3625 fdc_hw_init() is called at the beginning of the FDC
3626 setup. fdc_hw_init() must be provided by the board
3627 source code. It is used to make hardware dependant
3631 Most IDE controllers were designed to be connected with PCI
3632 interface. Only few of them were designed for AHB interface.
3633 When software is doing ATA command and data transfer to
3634 IDE devices through IDE-AHB controller, some additional
3635 registers accessing to these kind of IDE-AHB controller
3638 - CONFIG_SYS_IMMR: Physical address of the Internal Memory.
3639 DO NOT CHANGE unless you know exactly what you're
3640 doing! (11-4) [MPC8xx/82xx systems only]
3642 - CONFIG_SYS_INIT_RAM_ADDR:
3644 Start address of memory area that can be used for
3645 initial data and stack; please note that this must be
3646 writable memory that is working WITHOUT special
3647 initialization, i. e. you CANNOT use normal RAM which
3648 will become available only after programming the
3649 memory controller and running certain initialization
3652 U-Boot uses the following memory types:
3653 - MPC8xx and MPC8260: IMMR (internal memory of the CPU)
3654 - MPC824X: data cache
3655 - PPC4xx: data cache
3657 - CONFIG_SYS_GBL_DATA_OFFSET:
3659 Offset of the initial data structure in the memory
3660 area defined by CONFIG_SYS_INIT_RAM_ADDR. Usually
3661 CONFIG_SYS_GBL_DATA_OFFSET is chosen such that the initial
3662 data is located at the end of the available space
3663 (sometimes written as (CONFIG_SYS_INIT_RAM_SIZE -
3664 CONFIG_SYS_INIT_DATA_SIZE), and the initial stack is just
3665 below that area (growing from (CONFIG_SYS_INIT_RAM_ADDR +
3666 CONFIG_SYS_GBL_DATA_OFFSET) downward.
3669 On the MPC824X (or other systems that use the data
3670 cache for initial memory) the address chosen for
3671 CONFIG_SYS_INIT_RAM_ADDR is basically arbitrary - it must
3672 point to an otherwise UNUSED address space between
3673 the top of RAM and the start of the PCI space.
3675 - CONFIG_SYS_SIUMCR: SIU Module Configuration (11-6)
3677 - CONFIG_SYS_SYPCR: System Protection Control (11-9)
3679 - CONFIG_SYS_TBSCR: Time Base Status and Control (11-26)
3681 - CONFIG_SYS_PISCR: Periodic Interrupt Status and Control (11-31)
3683 - CONFIG_SYS_PLPRCR: PLL, Low-Power, and Reset Control Register (15-30)
3685 - CONFIG_SYS_SCCR: System Clock and reset Control Register (15-27)
3687 - CONFIG_SYS_OR_TIMING_SDRAM:
3690 - CONFIG_SYS_MAMR_PTA:
3691 periodic timer for refresh
3693 - CONFIG_SYS_DER: Debug Event Register (37-47)
3695 - FLASH_BASE0_PRELIM, FLASH_BASE1_PRELIM, CONFIG_SYS_REMAP_OR_AM,
3696 CONFIG_SYS_PRELIM_OR_AM, CONFIG_SYS_OR_TIMING_FLASH, CONFIG_SYS_OR0_REMAP,
3697 CONFIG_SYS_OR0_PRELIM, CONFIG_SYS_BR0_PRELIM, CONFIG_SYS_OR1_REMAP, CONFIG_SYS_OR1_PRELIM,
3698 CONFIG_SYS_BR1_PRELIM:
3699 Memory Controller Definitions: BR0/1 and OR0/1 (FLASH)
3701 - SDRAM_BASE2_PRELIM, SDRAM_BASE3_PRELIM, SDRAM_MAX_SIZE,
3702 CONFIG_SYS_OR_TIMING_SDRAM, CONFIG_SYS_OR2_PRELIM, CONFIG_SYS_BR2_PRELIM,
3703 CONFIG_SYS_OR3_PRELIM, CONFIG_SYS_BR3_PRELIM:
3704 Memory Controller Definitions: BR2/3 and OR2/3 (SDRAM)
3706 - CONFIG_SYS_MAMR_PTA, CONFIG_SYS_MPTPR_2BK_4K, CONFIG_SYS_MPTPR_1BK_4K, CONFIG_SYS_MPTPR_2BK_8K,
3707 CONFIG_SYS_MPTPR_1BK_8K, CONFIG_SYS_MAMR_8COL, CONFIG_SYS_MAMR_9COL:
3708 Machine Mode Register and Memory Periodic Timer
3709 Prescaler definitions (SDRAM timing)
3711 - CONFIG_SYS_I2C_UCODE_PATCH, CONFIG_SYS_I2C_DPMEM_OFFSET [0x1FC0]:
3712 enable I2C microcode relocation patch (MPC8xx);
3713 define relocation offset in DPRAM [DSP2]
3715 - CONFIG_SYS_SMC_UCODE_PATCH, CONFIG_SYS_SMC_DPMEM_OFFSET [0x1FC0]:
3716 enable SMC microcode relocation patch (MPC8xx);
3717 define relocation offset in DPRAM [SMC1]
3719 - CONFIG_SYS_SPI_UCODE_PATCH, CONFIG_SYS_SPI_DPMEM_OFFSET [0x1FC0]:
3720 enable SPI microcode relocation patch (MPC8xx);
3721 define relocation offset in DPRAM [SCC4]
3723 - CONFIG_SYS_USE_OSCCLK:
3724 Use OSCM clock mode on MBX8xx board. Be careful,
3725 wrong setting might damage your board. Read
3726 doc/README.MBX before setting this variable!
3728 - CONFIG_SYS_CPM_POST_WORD_ADDR: (MPC8xx, MPC8260 only)
3729 Offset of the bootmode word in DPRAM used by post
3730 (Power On Self Tests). This definition overrides
3731 #define'd default value in commproc.h resp.
3734 - CONFIG_SYS_PCI_SLV_MEM_LOCAL, CONFIG_SYS_PCI_SLV_MEM_BUS, CONFIG_SYS_PICMR0_MASK_ATTRIB,
3735 CONFIG_SYS_PCI_MSTR0_LOCAL, CONFIG_SYS_PCIMSK0_MASK, CONFIG_SYS_PCI_MSTR1_LOCAL,
3736 CONFIG_SYS_PCIMSK1_MASK, CONFIG_SYS_PCI_MSTR_MEM_LOCAL, CONFIG_SYS_PCI_MSTR_MEM_BUS,
3737 CONFIG_SYS_CPU_PCI_MEM_START, CONFIG_SYS_PCI_MSTR_MEM_SIZE, CONFIG_SYS_POCMR0_MASK_ATTRIB,
3738 CONFIG_SYS_PCI_MSTR_MEMIO_LOCAL, CONFIG_SYS_PCI_MSTR_MEMIO_BUS, CPU_PCI_MEMIO_START,
3739 CONFIG_SYS_PCI_MSTR_MEMIO_SIZE, CONFIG_SYS_POCMR1_MASK_ATTRIB, CONFIG_SYS_PCI_MSTR_IO_LOCAL,
3740 CONFIG_SYS_PCI_MSTR_IO_BUS, CONFIG_SYS_CPU_PCI_IO_START, CONFIG_SYS_PCI_MSTR_IO_SIZE,
3741 CONFIG_SYS_POCMR2_MASK_ATTRIB: (MPC826x only)
3742 Overrides the default PCI memory map in arch/powerpc/cpu/mpc8260/pci.c if set.
3744 - CONFIG_PCI_DISABLE_PCIE:
3745 Disable PCI-Express on systems where it is supported but not
3748 - CONFIG_PCI_ENUM_ONLY
3749 Only scan through and get the devices on the busses.
3750 Don't do any setup work, presumably because someone or
3751 something has already done it, and we don't need to do it
3752 a second time. Useful for platforms that are pre-booted
3753 by coreboot or similar.
3756 Chip has SRIO or not
3759 Board has SRIO 1 port available
3762 Board has SRIO 2 port available
3764 - CONFIG_SYS_SRIOn_MEM_VIRT:
3765 Virtual Address of SRIO port 'n' memory region
3767 - CONFIG_SYS_SRIOn_MEM_PHYS:
3768 Physical Address of SRIO port 'n' memory region
3770 - CONFIG_SYS_SRIOn_MEM_SIZE:
3771 Size of SRIO port 'n' memory region
3773 - CONFIG_SYS_NDFC_16
3774 Defined to tell the NDFC that the NAND chip is using a
3777 - CONFIG_SYS_NDFC_EBC0_CFG
3778 Sets the EBC0_CFG register for the NDFC. If not defined
3779 a default value will be used.
3782 Get DDR timing information from an I2C EEPROM. Common
3783 with pluggable memory modules such as SODIMMs
3786 I2C address of the SPD EEPROM
3788 - CONFIG_SYS_SPD_BUS_NUM
3789 If SPD EEPROM is on an I2C bus other than the first
3790 one, specify here. Note that the value must resolve
3791 to something your driver can deal with.
3793 - CONFIG_SYS_DDR_RAW_TIMING
3794 Get DDR timing information from other than SPD. Common with
3795 soldered DDR chips onboard without SPD. DDR raw timing
3796 parameters are extracted from datasheet and hard-coded into
3797 header files or board specific files.
3799 - CONFIG_FSL_DDR_INTERACTIVE
3800 Enable interactive DDR debugging. See doc/README.fsl-ddr.
3802 - CONFIG_SYS_83XX_DDR_USES_CS0
3803 Only for 83xx systems. If specified, then DDR should
3804 be configured using CS0 and CS1 instead of CS2 and CS3.
3806 - CONFIG_ETHER_ON_FEC[12]
3807 Define to enable FEC[12] on a 8xx series processor.
3809 - CONFIG_FEC[12]_PHY
3810 Define to the hardcoded PHY address which corresponds
3811 to the given FEC; i. e.
3812 #define CONFIG_FEC1_PHY 4
3813 means that the PHY with address 4 is connected to FEC1
3815 When set to -1, means to probe for first available.
3817 - CONFIG_FEC[12]_PHY_NORXERR
3818 The PHY does not have a RXERR line (RMII only).
3819 (so program the FEC to ignore it).
3822 Enable RMII mode for all FECs.
3823 Note that this is a global option, we can't
3824 have one FEC in standard MII mode and another in RMII mode.
3826 - CONFIG_CRC32_VERIFY
3827 Add a verify option to the crc32 command.
3830 => crc32 -v <address> <count> <crc32>
3832 Where address/count indicate a memory area
3833 and crc32 is the correct crc32 which the
3837 Add the "loopw" memory command. This only takes effect if
3838 the memory commands are activated globally (CONFIG_CMD_MEM).
3841 Add the "mdc" and "mwc" memory commands. These are cyclic
3846 This command will print 4 bytes (10,11,12,13) each 500 ms.
3848 => mwc.l 100 12345678 10
3849 This command will write 12345678 to address 100 all 10 ms.
3851 This only takes effect if the memory commands are activated
3852 globally (CONFIG_CMD_MEM).
3854 - CONFIG_SKIP_LOWLEVEL_INIT
3855 [ARM, NDS32, MIPS only] If this variable is defined, then certain
3856 low level initializations (like setting up the memory
3857 controller) are omitted and/or U-Boot does not
3858 relocate itself into RAM.
3860 Normally this variable MUST NOT be defined. The only
3861 exception is when U-Boot is loaded (to RAM) by some
3862 other boot loader or by a debugger which performs
3863 these initializations itself.
3866 Modifies the behaviour of start.S when compiling a loader
3867 that is executed before the actual U-Boot. E.g. when
3868 compiling a NAND SPL.
3870 - CONFIG_ARCH_MAP_SYSMEM
3871 Generally U-Boot (and in particular the md command) uses
3872 effective address. It is therefore not necessary to regard
3873 U-Boot address as virtual addresses that need to be translated
3874 to physical addresses. However, sandbox requires this, since
3875 it maintains its own little RAM buffer which contains all
3876 addressable memory. This option causes some memory accesses
3877 to be mapped through map_sysmem() / unmap_sysmem().
3879 - CONFIG_USE_ARCH_MEMCPY
3880 CONFIG_USE_ARCH_MEMSET
3881 If these options are used a optimized version of memcpy/memset will
3882 be used if available. These functions may be faster under some
3883 conditions but may increase the binary size.
3885 - CONFIG_X86_RESET_VECTOR
3886 If defined, the x86 reset vector code is included. This is not
3887 needed when U-Boot is running from Coreboot.
3890 Defines the MPU clock speed (in MHz).
3892 NOTE : currently only supported on AM335x platforms.
3894 Freescale QE/FMAN Firmware Support:
3895 -----------------------------------
3897 The Freescale QUICCEngine (QE) and Frame Manager (FMAN) both support the
3898 loading of "firmware", which is encoded in the QE firmware binary format.
3899 This firmware often needs to be loaded during U-Boot booting, so macros
3900 are used to identify the storage device (NOR flash, SPI, etc) and the address
3903 - CONFIG_SYS_QE_FMAN_FW_ADDR
3904 The address in the storage device where the firmware is located. The
3905 meaning of this address depends on which CONFIG_SYS_QE_FW_IN_xxx macro
3908 - CONFIG_SYS_QE_FMAN_FW_LENGTH
3909 The maximum possible size of the firmware. The firmware binary format
3910 has a field that specifies the actual size of the firmware, but it
3911 might not be possible to read any part of the firmware unless some
3912 local storage is allocated to hold the entire firmware first.
3914 - CONFIG_SYS_QE_FMAN_FW_IN_NOR
3915 Specifies that QE/FMAN firmware is located in NOR flash, mapped as
3916 normal addressable memory via the LBC. CONFIG_SYS_FMAN_FW_ADDR is the
3917 virtual address in NOR flash.
3919 - CONFIG_SYS_QE_FMAN_FW_IN_NAND
3920 Specifies that QE/FMAN firmware is located in NAND flash.
3921 CONFIG_SYS_FMAN_FW_ADDR is the offset within NAND flash.
3923 - CONFIG_SYS_QE_FMAN_FW_IN_MMC
3924 Specifies that QE/FMAN firmware is located on the primary SD/MMC
3925 device. CONFIG_SYS_FMAN_FW_ADDR is the byte offset on that device.
3927 - CONFIG_SYS_QE_FMAN_FW_IN_SPIFLASH
3928 Specifies that QE/FMAN firmware is located on the primary SPI
3929 device. CONFIG_SYS_FMAN_FW_ADDR is the byte offset on that device.
3931 - CONFIG_SYS_QE_FMAN_FW_IN_REMOTE
3932 Specifies that QE/FMAN firmware is located in the remote (master)
3933 memory space. CONFIG_SYS_FMAN_FW_ADDR is a virtual address which
3934 can be mapped from slave TLB->slave LAW->slave SRIO or PCIE outbound
3935 window->master inbound window->master LAW->the ucode address in
3936 master's memory space.
3938 Building the Software:
3939 ======================
3941 Building U-Boot has been tested in several native build environments
3942 and in many different cross environments. Of course we cannot support
3943 all possibly existing versions of cross development tools in all
3944 (potentially obsolete) versions. In case of tool chain problems we
3945 recommend to use the ELDK (see http://www.denx.de/wiki/DULG/ELDK)
3946 which is extensively used to build and test U-Boot.
3948 If you are not using a native environment, it is assumed that you
3949 have GNU cross compiling tools available in your path. In this case,
3950 you must set the environment variable CROSS_COMPILE in your shell.
3951 Note that no changes to the Makefile or any other source files are
3952 necessary. For example using the ELDK on a 4xx CPU, please enter:
3954 $ CROSS_COMPILE=ppc_4xx-
3955 $ export CROSS_COMPILE
3957 Note: If you wish to generate Windows versions of the utilities in
3958 the tools directory you can use the MinGW toolchain
3959 (http://www.mingw.org). Set your HOST tools to the MinGW
3960 toolchain and execute 'make tools'. For example:
3962 $ make HOSTCC=i586-mingw32msvc-gcc HOSTSTRIP=i586-mingw32msvc-strip tools
3964 Binaries such as tools/mkimage.exe will be created which can
3965 be executed on computers running Windows.
3967 U-Boot is intended to be simple to build. After installing the
3968 sources you must configure U-Boot for one specific board type. This
3973 where "NAME_config" is the name of one of the existing configu-
3974 rations; see boards.cfg for supported names.
3976 Note: for some board special configuration names may exist; check if
3977 additional information is available from the board vendor; for
3978 instance, the TQM823L systems are available without (standard)
3979 or with LCD support. You can select such additional "features"
3980 when choosing the configuration, i. e.
3983 - will configure for a plain TQM823L, i. e. no LCD support
3985 make TQM823L_LCD_config
3986 - will configure for a TQM823L with U-Boot console on LCD
3991 Finally, type "make all", and you should get some working U-Boot
3992 images ready for download to / installation on your system:
3994 - "u-boot.bin" is a raw binary image
3995 - "u-boot" is an image in ELF binary format
3996 - "u-boot.srec" is in Motorola S-Record format
3998 By default the build is performed locally and the objects are saved
3999 in the source directory. One of the two methods can be used to change
4000 this behavior and build U-Boot to some external directory:
4002 1. Add O= to the make command line invocations:
4004 make O=/tmp/build distclean
4005 make O=/tmp/build NAME_config
4006 make O=/tmp/build all
4008 2. Set environment variable BUILD_DIR to point to the desired location:
4010 export BUILD_DIR=/tmp/build
4015 Note that the command line "O=" setting overrides the BUILD_DIR environment
4019 Please be aware that the Makefiles assume you are using GNU make, so
4020 for instance on NetBSD you might need to use "gmake" instead of
4024 If the system board that you have is not listed, then you will need
4025 to port U-Boot to your hardware platform. To do this, follow these
4028 1. Add a new configuration option for your board to the toplevel
4029 "boards.cfg" file, using the existing entries as examples.
4030 Follow the instructions there to keep the boards in order.
4031 2. Create a new directory to hold your board specific code. Add any
4032 files you need. In your board directory, you will need at least
4033 the "Makefile", a "<board>.c", "flash.c" and "u-boot.lds".
4034 3. Create a new configuration file "include/configs/<board>.h" for
4036 3. If you're porting U-Boot to a new CPU, then also create a new
4037 directory to hold your CPU specific code. Add any files you need.
4038 4. Run "make <board>_config" with your new name.
4039 5. Type "make", and you should get a working "u-boot.srec" file
4040 to be installed on your target system.
4041 6. Debug and solve any problems that might arise.
4042 [Of course, this last step is much harder than it sounds.]
4045 Testing of U-Boot Modifications, Ports to New Hardware, etc.:
4046 ==============================================================
4048 If you have modified U-Boot sources (for instance added a new board
4049 or support for new devices, a new CPU, etc.) you are expected to
4050 provide feedback to the other developers. The feedback normally takes
4051 the form of a "patch", i. e. a context diff against a certain (latest
4052 official or latest in the git repository) version of U-Boot sources.
4054 But before you submit such a patch, please verify that your modifi-
4055 cation did not break existing code. At least make sure that *ALL* of
4056 the supported boards compile WITHOUT ANY compiler warnings. To do so,
4057 just run the "MAKEALL" script, which will configure and build U-Boot
4058 for ALL supported system. Be warned, this will take a while. You can
4059 select which (cross) compiler to use by passing a `CROSS_COMPILE'
4060 environment variable to the script, i. e. to use the ELDK cross tools
4063 CROSS_COMPILE=ppc_8xx- MAKEALL
4065 or to build on a native PowerPC system you can type
4067 CROSS_COMPILE=' ' MAKEALL
4069 When using the MAKEALL script, the default behaviour is to build
4070 U-Boot in the source directory. This location can be changed by
4071 setting the BUILD_DIR environment variable. Also, for each target
4072 built, the MAKEALL script saves two log files (<target>.ERR and
4073 <target>.MAKEALL) in the <source dir>/LOG directory. This default
4074 location can be changed by setting the MAKEALL_LOGDIR environment
4075 variable. For example:
4077 export BUILD_DIR=/tmp/build
4078 export MAKEALL_LOGDIR=/tmp/log
4079 CROSS_COMPILE=ppc_8xx- MAKEALL
4081 With the above settings build objects are saved in the /tmp/build,
4082 log files are saved in the /tmp/log and the source tree remains clean
4083 during the whole build process.
4086 See also "U-Boot Porting Guide" below.
4089 Monitor Commands - Overview:
4090 ============================
4092 go - start application at address 'addr'
4093 run - run commands in an environment variable
4094 bootm - boot application image from memory
4095 bootp - boot image via network using BootP/TFTP protocol
4096 bootz - boot zImage from memory
4097 tftpboot- boot image via network using TFTP protocol
4098 and env variables "ipaddr" and "serverip"
4099 (and eventually "gatewayip")
4100 tftpput - upload a file via network using TFTP protocol
4101 rarpboot- boot image via network using RARP/TFTP protocol
4102 diskboot- boot from IDE devicebootd - boot default, i.e., run 'bootcmd'
4103 loads - load S-Record file over serial line
4104 loadb - load binary file over serial line (kermit mode)
4106 mm - memory modify (auto-incrementing)
4107 nm - memory modify (constant address)
4108 mw - memory write (fill)
4110 cmp - memory compare
4111 crc32 - checksum calculation
4112 i2c - I2C sub-system
4113 sspi - SPI utility commands
4114 base - print or set address offset
4115 printenv- print environment variables
4116 setenv - set environment variables
4117 saveenv - save environment variables to persistent storage
4118 protect - enable or disable FLASH write protection
4119 erase - erase FLASH memory
4120 flinfo - print FLASH memory information
4121 nand - NAND memory operations (see doc/README.nand)
4122 bdinfo - print Board Info structure
4123 iminfo - print header information for application image
4124 coninfo - print console devices and informations
4125 ide - IDE sub-system
4126 loop - infinite loop on address range
4127 loopw - infinite write loop on address range
4128 mtest - simple RAM test
4129 icache - enable or disable instruction cache
4130 dcache - enable or disable data cache
4131 reset - Perform RESET of the CPU
4132 echo - echo args to console
4133 version - print monitor version
4134 help - print online help
4135 ? - alias for 'help'
4138 Monitor Commands - Detailed Description:
4139 ========================================
4143 For now: just type "help <command>".
4146 Environment Variables:
4147 ======================
4149 U-Boot supports user configuration using Environment Variables which
4150 can be made persistent by saving to Flash memory.
4152 Environment Variables are set using "setenv", printed using
4153 "printenv", and saved to Flash using "saveenv". Using "setenv"
4154 without a value can be used to delete a variable from the
4155 environment. As long as you don't save the environment you are
4156 working with an in-memory copy. In case the Flash area containing the
4157 environment is erased by accident, a default environment is provided.
4159 Some configuration options can be set using Environment Variables.
4161 List of environment variables (most likely not complete):
4163 baudrate - see CONFIG_BAUDRATE
4165 bootdelay - see CONFIG_BOOTDELAY
4167 bootcmd - see CONFIG_BOOTCOMMAND
4169 bootargs - Boot arguments when booting an RTOS image
4171 bootfile - Name of the image to load with TFTP
4173 bootm_low - Memory range available for image processing in the bootm
4174 command can be restricted. This variable is given as
4175 a hexadecimal number and defines lowest address allowed
4176 for use by the bootm command. See also "bootm_size"
4177 environment variable. Address defined by "bootm_low" is
4178 also the base of the initial memory mapping for the Linux
4179 kernel -- see the description of CONFIG_SYS_BOOTMAPSZ and
4182 bootm_mapsize - Size of the initial memory mapping for the Linux kernel.
4183 This variable is given as a hexadecimal number and it
4184 defines the size of the memory region starting at base
4185 address bootm_low that is accessible by the Linux kernel
4186 during early boot. If unset, CONFIG_SYS_BOOTMAPSZ is used
4187 as the default value if it is defined, and bootm_size is
4190 bootm_size - Memory range available for image processing in the bootm
4191 command can be restricted. This variable is given as
4192 a hexadecimal number and defines the size of the region
4193 allowed for use by the bootm command. See also "bootm_low"
4194 environment variable.
4196 updatefile - Location of the software update file on a TFTP server, used
4197 by the automatic software update feature. Please refer to
4198 documentation in doc/README.update for more details.
4200 autoload - if set to "no" (any string beginning with 'n'),
4201 "bootp" will just load perform a lookup of the
4202 configuration from the BOOTP server, but not try to
4203 load any image using TFTP
4205 autostart - if set to "yes", an image loaded using the "bootp",
4206 "rarpboot", "tftpboot" or "diskboot" commands will
4207 be automatically started (by internally calling
4210 If set to "no", a standalone image passed to the
4211 "bootm" command will be copied to the load address
4212 (and eventually uncompressed), but NOT be started.
4213 This can be used to load and uncompress arbitrary
4216 fdt_high - if set this restricts the maximum address that the
4217 flattened device tree will be copied into upon boot.
4218 For example, if you have a system with 1 GB memory
4219 at physical address 0x10000000, while Linux kernel
4220 only recognizes the first 704 MB as low memory, you
4221 may need to set fdt_high as 0x3C000000 to have the
4222 device tree blob be copied to the maximum address
4223 of the 704 MB low memory, so that Linux kernel can
4224 access it during the boot procedure.
4226 If this is set to the special value 0xFFFFFFFF then
4227 the fdt will not be copied at all on boot. For this
4228 to work it must reside in writable memory, have
4229 sufficient padding on the end of it for u-boot to
4230 add the information it needs into it, and the memory
4231 must be accessible by the kernel.
4233 fdtcontroladdr- if set this is the address of the control flattened
4234 device tree used by U-Boot when CONFIG_OF_CONTROL is
4237 i2cfast - (PPC405GP|PPC405EP only)
4238 if set to 'y' configures Linux I2C driver for fast
4239 mode (400kHZ). This environment variable is used in
4240 initialization code. So, for changes to be effective
4241 it must be saved and board must be reset.
4243 initrd_high - restrict positioning of initrd images:
4244 If this variable is not set, initrd images will be
4245 copied to the highest possible address in RAM; this
4246 is usually what you want since it allows for
4247 maximum initrd size. If for some reason you want to
4248 make sure that the initrd image is loaded below the
4249 CONFIG_SYS_BOOTMAPSZ limit, you can set this environment
4250 variable to a value of "no" or "off" or "0".
4251 Alternatively, you can set it to a maximum upper
4252 address to use (U-Boot will still check that it
4253 does not overwrite the U-Boot stack and data).
4255 For instance, when you have a system with 16 MB
4256 RAM, and want to reserve 4 MB from use by Linux,
4257 you can do this by adding "mem=12M" to the value of
4258 the "bootargs" variable. However, now you must make
4259 sure that the initrd image is placed in the first
4260 12 MB as well - this can be done with
4262 setenv initrd_high 00c00000
4264 If you set initrd_high to 0xFFFFFFFF, this is an
4265 indication to U-Boot that all addresses are legal
4266 for the Linux kernel, including addresses in flash
4267 memory. In this case U-Boot will NOT COPY the
4268 ramdisk at all. This may be useful to reduce the
4269 boot time on your system, but requires that this
4270 feature is supported by your Linux kernel.
4272 ipaddr - IP address; needed for tftpboot command
4274 loadaddr - Default load address for commands like "bootp",
4275 "rarpboot", "tftpboot", "loadb" or "diskboot"
4277 loads_echo - see CONFIG_LOADS_ECHO
4279 serverip - TFTP server IP address; needed for tftpboot command
4281 bootretry - see CONFIG_BOOT_RETRY_TIME
4283 bootdelaykey - see CONFIG_AUTOBOOT_DELAY_STR
4285 bootstopkey - see CONFIG_AUTOBOOT_STOP_STR
4287 ethprime - controls which interface is used first.
4289 ethact - controls which interface is currently active.
4290 For example you can do the following
4292 => setenv ethact FEC
4293 => ping 192.168.0.1 # traffic sent on FEC
4294 => setenv ethact SCC
4295 => ping 10.0.0.1 # traffic sent on SCC
4297 ethrotate - When set to "no" U-Boot does not go through all
4298 available network interfaces.
4299 It just stays at the currently selected interface.
4301 netretry - When set to "no" each network operation will
4302 either succeed or fail without retrying.
4303 When set to "once" the network operation will
4304 fail when all the available network interfaces
4305 are tried once without success.
4306 Useful on scripts which control the retry operation
4309 npe_ucode - set load address for the NPE microcode
4311 tftpsrcport - If this is set, the value is used for TFTP's
4314 tftpdstport - If this is set, the value is used for TFTP's UDP
4315 destination port instead of the Well Know Port 69.
4317 tftpblocksize - Block size to use for TFTP transfers; if not set,
4318 we use the TFTP server's default block size
4320 tftptimeout - Retransmission timeout for TFTP packets (in milli-
4321 seconds, minimum value is 1000 = 1 second). Defines
4322 when a packet is considered to be lost so it has to
4323 be retransmitted. The default is 5000 = 5 seconds.
4324 Lowering this value may make downloads succeed
4325 faster in networks with high packet loss rates or
4326 with unreliable TFTP servers.
4328 vlan - When set to a value < 4095 the traffic over
4329 Ethernet is encapsulated/received over 802.1q
4332 The following image location variables contain the location of images
4333 used in booting. The "Image" column gives the role of the image and is
4334 not an environment variable name. The other columns are environment
4335 variable names. "File Name" gives the name of the file on a TFTP
4336 server, "RAM Address" gives the location in RAM the image will be
4337 loaded to, and "Flash Location" gives the image's address in NOR
4338 flash or offset in NAND flash.
4340 *Note* - these variables don't have to be defined for all boards, some
4341 boards currenlty use other variables for these purposes, and some
4342 boards use these variables for other purposes.
4344 Image File Name RAM Address Flash Location
4345 ----- --------- ----------- --------------
4346 u-boot u-boot u-boot_addr_r u-boot_addr
4347 Linux kernel bootfile kernel_addr_r kernel_addr
4348 device tree blob fdtfile fdt_addr_r fdt_addr
4349 ramdisk ramdiskfile ramdisk_addr_r ramdisk_addr
4351 The following environment variables may be used and automatically
4352 updated by the network boot commands ("bootp" and "rarpboot"),
4353 depending the information provided by your boot server:
4355 bootfile - see above
4356 dnsip - IP address of your Domain Name Server
4357 dnsip2 - IP address of your secondary Domain Name Server
4358 gatewayip - IP address of the Gateway (Router) to use
4359 hostname - Target hostname
4361 netmask - Subnet Mask
4362 rootpath - Pathname of the root filesystem on the NFS server
4363 serverip - see above
4366 There are two special Environment Variables:
4368 serial# - contains hardware identification information such
4369 as type string and/or serial number
4370 ethaddr - Ethernet address
4372 These variables can be set only once (usually during manufacturing of
4373 the board). U-Boot refuses to delete or overwrite these variables
4374 once they have been set once.
4377 Further special Environment Variables:
4379 ver - Contains the U-Boot version string as printed
4380 with the "version" command. This variable is
4381 readonly (see CONFIG_VERSION_VARIABLE).
4384 Please note that changes to some configuration parameters may take
4385 only effect after the next boot (yes, that's just like Windoze :-).
4388 Callback functions for environment variables:
4389 ---------------------------------------------
4391 For some environment variables, the behavior of u-boot needs to change
4392 when their values are changed. This functionailty allows functions to
4393 be associated with arbitrary variables. On creation, overwrite, or
4394 deletion, the callback will provide the opportunity for some side
4395 effect to happen or for the change to be rejected.
4397 The callbacks are named and associated with a function using the
4398 U_BOOT_ENV_CALLBACK macro in your board or driver code.
4400 These callbacks are associated with variables in one of two ways. The
4401 static list can be added to by defining CONFIG_ENV_CALLBACK_LIST_STATIC
4402 in the board configuration to a string that defines a list of
4403 associations. The list must be in the following format:
4405 entry = variable_name[:callback_name]
4408 If the callback name is not specified, then the callback is deleted.
4409 Spaces are also allowed anywhere in the list.
4411 Callbacks can also be associated by defining the ".callbacks" variable
4412 with the same list format above. Any association in ".callbacks" will
4413 override any association in the static list. You can define
4414 CONFIG_ENV_CALLBACK_LIST_DEFAULT to a list (string) to define the
4415 ".callbacks" envirnoment variable in the default or embedded environment.
4418 Command Line Parsing:
4419 =====================
4421 There are two different command line parsers available with U-Boot:
4422 the old "simple" one, and the much more powerful "hush" shell:
4424 Old, simple command line parser:
4425 --------------------------------
4427 - supports environment variables (through setenv / saveenv commands)
4428 - several commands on one line, separated by ';'
4429 - variable substitution using "... ${name} ..." syntax
4430 - special characters ('$', ';') can be escaped by prefixing with '\',
4432 setenv bootcmd bootm \${address}
4433 - You can also escape text by enclosing in single apostrophes, for example:
4434 setenv addip 'setenv bootargs $bootargs ip=$ipaddr:$serverip:$gatewayip:$netmask:$hostname::off'
4439 - similar to Bourne shell, with control structures like
4440 if...then...else...fi, for...do...done; while...do...done,
4441 until...do...done, ...
4442 - supports environment ("global") variables (through setenv / saveenv
4443 commands) and local shell variables (through standard shell syntax
4444 "name=value"); only environment variables can be used with "run"
4450 (1) If a command line (or an environment variable executed by a "run"
4451 command) contains several commands separated by semicolon, and
4452 one of these commands fails, then the remaining commands will be
4455 (2) If you execute several variables with one call to run (i. e.
4456 calling run with a list of variables as arguments), any failing
4457 command will cause "run" to terminate, i. e. the remaining
4458 variables are not executed.
4460 Note for Redundant Ethernet Interfaces:
4461 =======================================
4463 Some boards come with redundant Ethernet interfaces; U-Boot supports
4464 such configurations and is capable of automatic selection of a
4465 "working" interface when needed. MAC assignment works as follows:
4467 Network interfaces are numbered eth0, eth1, eth2, ... Corresponding
4468 MAC addresses can be stored in the environment as "ethaddr" (=>eth0),
4469 "eth1addr" (=>eth1), "eth2addr", ...
4471 If the network interface stores some valid MAC address (for instance
4472 in SROM), this is used as default address if there is NO correspon-
4473 ding setting in the environment; if the corresponding environment
4474 variable is set, this overrides the settings in the card; that means:
4476 o If the SROM has a valid MAC address, and there is no address in the
4477 environment, the SROM's address is used.
4479 o If there is no valid address in the SROM, and a definition in the
4480 environment exists, then the value from the environment variable is
4483 o If both the SROM and the environment contain a MAC address, and
4484 both addresses are the same, this MAC address is used.
4486 o If both the SROM and the environment contain a MAC address, and the
4487 addresses differ, the value from the environment is used and a
4490 o If neither SROM nor the environment contain a MAC address, an error
4493 If Ethernet drivers implement the 'write_hwaddr' function, valid MAC addresses
4494 will be programmed into hardware as part of the initialization process. This
4495 may be skipped by setting the appropriate 'ethmacskip' environment variable.
4496 The naming convention is as follows:
4497 "ethmacskip" (=>eth0), "eth1macskip" (=>eth1) etc.
4502 U-Boot is capable of booting (and performing other auxiliary operations on)
4503 images in two formats:
4505 New uImage format (FIT)
4506 -----------------------
4508 Flexible and powerful format based on Flattened Image Tree -- FIT (similar
4509 to Flattened Device Tree). It allows the use of images with multiple
4510 components (several kernels, ramdisks, etc.), with contents protected by
4511 SHA1, MD5 or CRC32. More details are found in the doc/uImage.FIT directory.
4517 Old image format is based on binary files which can be basically anything,
4518 preceded by a special header; see the definitions in include/image.h for
4519 details; basically, the header defines the following image properties:
4521 * Target Operating System (Provisions for OpenBSD, NetBSD, FreeBSD,
4522 4.4BSD, Linux, SVR4, Esix, Solaris, Irix, SCO, Dell, NCR, VxWorks,
4523 LynxOS, pSOS, QNX, RTEMS, INTEGRITY;
4524 Currently supported: Linux, NetBSD, VxWorks, QNX, RTEMS, LynxOS,
4526 * Target CPU Architecture (Provisions for Alpha, ARM, AVR32, Intel x86,
4527 IA64, MIPS, NDS32, Nios II, PowerPC, IBM S390, SuperH, Sparc, Sparc 64 Bit;
4528 Currently supported: ARM, AVR32, Intel x86, MIPS, NDS32, Nios II, PowerPC).
4529 * Compression Type (uncompressed, gzip, bzip2)
4535 The header is marked by a special Magic Number, and both the header
4536 and the data portions of the image are secured against corruption by
4543 Although U-Boot should support any OS or standalone application
4544 easily, the main focus has always been on Linux during the design of
4547 U-Boot includes many features that so far have been part of some
4548 special "boot loader" code within the Linux kernel. Also, any
4549 "initrd" images to be used are no longer part of one big Linux image;
4550 instead, kernel and "initrd" are separate images. This implementation
4551 serves several purposes:
4553 - the same features can be used for other OS or standalone
4554 applications (for instance: using compressed images to reduce the
4555 Flash memory footprint)
4557 - it becomes much easier to port new Linux kernel versions because
4558 lots of low-level, hardware dependent stuff are done by U-Boot
4560 - the same Linux kernel image can now be used with different "initrd"
4561 images; of course this also means that different kernel images can
4562 be run with the same "initrd". This makes testing easier (you don't
4563 have to build a new "zImage.initrd" Linux image when you just
4564 change a file in your "initrd"). Also, a field-upgrade of the
4565 software is easier now.
4571 Porting Linux to U-Boot based systems:
4572 ---------------------------------------
4574 U-Boot cannot save you from doing all the necessary modifications to
4575 configure the Linux device drivers for use with your target hardware
4576 (no, we don't intend to provide a full virtual machine interface to
4579 But now you can ignore ALL boot loader code (in arch/powerpc/mbxboot).
4581 Just make sure your machine specific header file (for instance
4582 include/asm-ppc/tqm8xx.h) includes the same definition of the Board
4583 Information structure as we define in include/asm-<arch>/u-boot.h,
4584 and make sure that your definition of IMAP_ADDR uses the same value
4585 as your U-Boot configuration in CONFIG_SYS_IMMR.
4588 Configuring the Linux kernel:
4589 -----------------------------
4591 No specific requirements for U-Boot. Make sure you have some root
4592 device (initial ramdisk, NFS) for your target system.
4595 Building a Linux Image:
4596 -----------------------
4598 With U-Boot, "normal" build targets like "zImage" or "bzImage" are
4599 not used. If you use recent kernel source, a new build target
4600 "uImage" will exist which automatically builds an image usable by
4601 U-Boot. Most older kernels also have support for a "pImage" target,
4602 which was introduced for our predecessor project PPCBoot and uses a
4603 100% compatible format.
4612 The "uImage" build target uses a special tool (in 'tools/mkimage') to
4613 encapsulate a compressed Linux kernel image with header information,
4614 CRC32 checksum etc. for use with U-Boot. This is what we are doing:
4616 * build a standard "vmlinux" kernel image (in ELF binary format):
4618 * convert the kernel into a raw binary image:
4620 ${CROSS_COMPILE}-objcopy -O binary \
4621 -R .note -R .comment \
4622 -S vmlinux linux.bin
4624 * compress the binary image:
4628 * package compressed binary image for U-Boot:
4630 mkimage -A ppc -O linux -T kernel -C gzip \
4631 -a 0 -e 0 -n "Linux Kernel Image" \
4632 -d linux.bin.gz uImage
4635 The "mkimage" tool can also be used to create ramdisk images for use
4636 with U-Boot, either separated from the Linux kernel image, or
4637 combined into one file. "mkimage" encapsulates the images with a 64
4638 byte header containing information about target architecture,
4639 operating system, image type, compression method, entry points, time
4640 stamp, CRC32 checksums, etc.
4642 "mkimage" can be called in two ways: to verify existing images and
4643 print the header information, or to build new images.
4645 In the first form (with "-l" option) mkimage lists the information
4646 contained in the header of an existing U-Boot image; this includes
4647 checksum verification:
4649 tools/mkimage -l image
4650 -l ==> list image header information
4652 The second form (with "-d" option) is used to build a U-Boot image
4653 from a "data file" which is used as image payload:
4655 tools/mkimage -A arch -O os -T type -C comp -a addr -e ep \
4656 -n name -d data_file image
4657 -A ==> set architecture to 'arch'
4658 -O ==> set operating system to 'os'
4659 -T ==> set image type to 'type'
4660 -C ==> set compression type 'comp'
4661 -a ==> set load address to 'addr' (hex)
4662 -e ==> set entry point to 'ep' (hex)
4663 -n ==> set image name to 'name'
4664 -d ==> use image data from 'datafile'
4666 Right now, all Linux kernels for PowerPC systems use the same load
4667 address (0x00000000), but the entry point address depends on the
4670 - 2.2.x kernels have the entry point at 0x0000000C,
4671 - 2.3.x and later kernels have the entry point at 0x00000000.
4673 So a typical call to build a U-Boot image would read:
4675 -> tools/mkimage -n '2.4.4 kernel for TQM850L' \
4676 > -A ppc -O linux -T kernel -C gzip -a 0 -e 0 \
4677 > -d /opt/elsk/ppc_8xx/usr/src/linux-2.4.4/arch/powerpc/coffboot/vmlinux.gz \
4678 > examples/uImage.TQM850L
4679 Image Name: 2.4.4 kernel for TQM850L
4680 Created: Wed Jul 19 02:34:59 2000
4681 Image Type: PowerPC Linux Kernel Image (gzip compressed)
4682 Data Size: 335725 Bytes = 327.86 kB = 0.32 MB
4683 Load Address: 0x00000000
4684 Entry Point: 0x00000000
4686 To verify the contents of the image (or check for corruption):
4688 -> tools/mkimage -l examples/uImage.TQM850L
4689 Image Name: 2.4.4 kernel for TQM850L
4690 Created: Wed Jul 19 02:34:59 2000
4691 Image Type: PowerPC Linux Kernel Image (gzip compressed)
4692 Data Size: 335725 Bytes = 327.86 kB = 0.32 MB
4693 Load Address: 0x00000000
4694 Entry Point: 0x00000000
4696 NOTE: for embedded systems where boot time is critical you can trade
4697 speed for memory and install an UNCOMPRESSED image instead: this
4698 needs more space in Flash, but boots much faster since it does not
4699 need to be uncompressed:
4701 -> gunzip /opt/elsk/ppc_8xx/usr/src/linux-2.4.4/arch/powerpc/coffboot/vmlinux.gz
4702 -> tools/mkimage -n '2.4.4 kernel for TQM850L' \
4703 > -A ppc -O linux -T kernel -C none -a 0 -e 0 \
4704 > -d /opt/elsk/ppc_8xx/usr/src/linux-2.4.4/arch/powerpc/coffboot/vmlinux \
4705 > examples/uImage.TQM850L-uncompressed
4706 Image Name: 2.4.4 kernel for TQM850L
4707 Created: Wed Jul 19 02:34:59 2000
4708 Image Type: PowerPC Linux Kernel Image (uncompressed)
4709 Data Size: 792160 Bytes = 773.59 kB = 0.76 MB
4710 Load Address: 0x00000000
4711 Entry Point: 0x00000000
4714 Similar you can build U-Boot images from a 'ramdisk.image.gz' file
4715 when your kernel is intended to use an initial ramdisk:
4717 -> tools/mkimage -n 'Simple Ramdisk Image' \
4718 > -A ppc -O linux -T ramdisk -C gzip \
4719 > -d /LinuxPPC/images/SIMPLE-ramdisk.image.gz examples/simple-initrd
4720 Image Name: Simple Ramdisk Image
4721 Created: Wed Jan 12 14:01:50 2000
4722 Image Type: PowerPC Linux RAMDisk Image (gzip compressed)
4723 Data Size: 566530 Bytes = 553.25 kB = 0.54 MB
4724 Load Address: 0x00000000
4725 Entry Point: 0x00000000
4728 Installing a Linux Image:
4729 -------------------------
4731 To downloading a U-Boot image over the serial (console) interface,
4732 you must convert the image to S-Record format:
4734 objcopy -I binary -O srec examples/image examples/image.srec
4736 The 'objcopy' does not understand the information in the U-Boot
4737 image header, so the resulting S-Record file will be relative to
4738 address 0x00000000. To load it to a given address, you need to
4739 specify the target address as 'offset' parameter with the 'loads'
4742 Example: install the image to address 0x40100000 (which on the
4743 TQM8xxL is in the first Flash bank):
4745 => erase 40100000 401FFFFF
4751 ## Ready for S-Record download ...
4752 ~>examples/image.srec
4753 1 2 3 4 5 6 7 8 9 10 11 12 13 ...
4755 15989 15990 15991 15992
4756 [file transfer complete]
4758 ## Start Addr = 0x00000000
4761 You can check the success of the download using the 'iminfo' command;
4762 this includes a checksum verification so you can be sure no data
4763 corruption happened:
4767 ## Checking Image at 40100000 ...
4768 Image Name: 2.2.13 for initrd on TQM850L
4769 Image Type: PowerPC Linux Kernel Image (gzip compressed)
4770 Data Size: 335725 Bytes = 327 kB = 0 MB
4771 Load Address: 00000000
4772 Entry Point: 0000000c
4773 Verifying Checksum ... OK
4779 The "bootm" command is used to boot an application that is stored in
4780 memory (RAM or Flash). In case of a Linux kernel image, the contents
4781 of the "bootargs" environment variable is passed to the kernel as
4782 parameters. You can check and modify this variable using the
4783 "printenv" and "setenv" commands:
4786 => printenv bootargs
4787 bootargs=root=/dev/ram
4789 => setenv bootargs root=/dev/nfs rw nfsroot=10.0.0.2:/LinuxPPC nfsaddrs=10.0.0.99:10.0.0.2
4791 => printenv bootargs
4792 bootargs=root=/dev/nfs rw nfsroot=10.0.0.2:/LinuxPPC nfsaddrs=10.0.0.99:10.0.0.2
4795 ## Booting Linux kernel at 40020000 ...
4796 Image Name: 2.2.13 for NFS on TQM850L
4797 Image Type: PowerPC Linux Kernel Image (gzip compressed)
4798 Data Size: 381681 Bytes = 372 kB = 0 MB
4799 Load Address: 00000000
4800 Entry Point: 0000000c
4801 Verifying Checksum ... OK
4802 Uncompressing Kernel Image ... OK
4803 Linux version 2.2.13 (wd@denx.local.net) (gcc version 2.95.2 19991024 (release)) #1 Wed Jul 19 02:35:17 MEST 2000
4804 Boot arguments: root=/dev/nfs rw nfsroot=10.0.0.2:/LinuxPPC nfsaddrs=10.0.0.99:10.0.0.2
4805 time_init: decrementer frequency = 187500000/60
4806 Calibrating delay loop... 49.77 BogoMIPS
4807 Memory: 15208k available (700k kernel code, 444k data, 32k init) [c0000000,c1000000]
4810 If you want to boot a Linux kernel with initial RAM disk, you pass
4811 the memory addresses of both the kernel and the initrd image (PPBCOOT
4812 format!) to the "bootm" command:
4814 => imi 40100000 40200000
4816 ## Checking Image at 40100000 ...
4817 Image Name: 2.2.13 for initrd on TQM850L
4818 Image Type: PowerPC Linux Kernel Image (gzip compressed)
4819 Data Size: 335725 Bytes = 327 kB = 0 MB
4820 Load Address: 00000000
4821 Entry Point: 0000000c
4822 Verifying Checksum ... OK
4824 ## Checking Image at 40200000 ...
4825 Image Name: Simple Ramdisk Image
4826 Image Type: PowerPC Linux RAMDisk Image (gzip compressed)
4827 Data Size: 566530 Bytes = 553 kB = 0 MB
4828 Load Address: 00000000
4829 Entry Point: 00000000
4830 Verifying Checksum ... OK
4832 => bootm 40100000 40200000
4833 ## Booting Linux kernel at 40100000 ...
4834 Image Name: 2.2.13 for initrd on TQM850L
4835 Image Type: PowerPC Linux Kernel Image (gzip compressed)
4836 Data Size: 335725 Bytes = 327 kB = 0 MB
4837 Load Address: 00000000
4838 Entry Point: 0000000c
4839 Verifying Checksum ... OK
4840 Uncompressing Kernel Image ... OK
4841 ## Loading RAMDisk Image at 40200000 ...
4842 Image Name: Simple Ramdisk Image
4843 Image Type: PowerPC Linux RAMDisk Image (gzip compressed)
4844 Data Size: 566530 Bytes = 553 kB = 0 MB
4845 Load Address: 00000000
4846 Entry Point: 00000000
4847 Verifying Checksum ... OK
4848 Loading Ramdisk ... OK
4849 Linux version 2.2.13 (wd@denx.local.net) (gcc version 2.95.2 19991024 (release)) #1 Wed Jul 19 02:32:08 MEST 2000
4850 Boot arguments: root=/dev/ram
4851 time_init: decrementer frequency = 187500000/60
4852 Calibrating delay loop... 49.77 BogoMIPS
4854 RAMDISK: Compressed image found at block 0
4855 VFS: Mounted root (ext2 filesystem).
4859 Boot Linux and pass a flat device tree:
4862 First, U-Boot must be compiled with the appropriate defines. See the section
4863 titled "Linux Kernel Interface" above for a more in depth explanation. The
4864 following is an example of how to start a kernel and pass an updated
4870 oft=oftrees/mpc8540ads.dtb
4871 => tftp $oftaddr $oft
4872 Speed: 1000, full duplex
4874 TFTP from server 192.168.1.1; our IP address is 192.168.1.101
4875 Filename 'oftrees/mpc8540ads.dtb'.
4876 Load address: 0x300000
4879 Bytes transferred = 4106 (100a hex)
4880 => tftp $loadaddr $bootfile
4881 Speed: 1000, full duplex
4883 TFTP from server 192.168.1.1; our IP address is 192.168.1.2
4885 Load address: 0x200000
4886 Loading:############
4888 Bytes transferred = 1029407 (fb51f hex)
4893 => bootm $loadaddr - $oftaddr
4894 ## Booting image at 00200000 ...
4895 Image Name: Linux-2.6.17-dirty
4896 Image Type: PowerPC Linux Kernel Image (gzip compressed)
4897 Data Size: 1029343 Bytes = 1005.2 kB
4898 Load Address: 00000000
4899 Entry Point: 00000000
4900 Verifying Checksum ... OK
4901 Uncompressing Kernel Image ... OK
4902 Booting using flat device tree at 0x300000
4903 Using MPC85xx ADS machine description
4904 Memory CAM mapping: CAM0=256Mb, CAM1=256Mb, CAM2=0Mb residual: 0Mb
4908 More About U-Boot Image Types:
4909 ------------------------------
4911 U-Boot supports the following image types:
4913 "Standalone Programs" are directly runnable in the environment
4914 provided by U-Boot; it is expected that (if they behave
4915 well) you can continue to work in U-Boot after return from
4916 the Standalone Program.
4917 "OS Kernel Images" are usually images of some Embedded OS which
4918 will take over control completely. Usually these programs
4919 will install their own set of exception handlers, device
4920 drivers, set up the MMU, etc. - this means, that you cannot
4921 expect to re-enter U-Boot except by resetting the CPU.
4922 "RAMDisk Images" are more or less just data blocks, and their
4923 parameters (address, size) are passed to an OS kernel that is
4925 "Multi-File Images" contain several images, typically an OS
4926 (Linux) kernel image and one or more data images like
4927 RAMDisks. This construct is useful for instance when you want
4928 to boot over the network using BOOTP etc., where the boot
4929 server provides just a single image file, but you want to get
4930 for instance an OS kernel and a RAMDisk image.
4932 "Multi-File Images" start with a list of image sizes, each
4933 image size (in bytes) specified by an "uint32_t" in network
4934 byte order. This list is terminated by an "(uint32_t)0".
4935 Immediately after the terminating 0 follow the images, one by
4936 one, all aligned on "uint32_t" boundaries (size rounded up to
4937 a multiple of 4 bytes).
4939 "Firmware Images" are binary images containing firmware (like
4940 U-Boot or FPGA images) which usually will be programmed to
4943 "Script files" are command sequences that will be executed by
4944 U-Boot's command interpreter; this feature is especially
4945 useful when you configure U-Boot to use a real shell (hush)
4946 as command interpreter.
4948 Booting the Linux zImage:
4949 -------------------------
4951 On some platforms, it's possible to boot Linux zImage. This is done
4952 using the "bootz" command. The syntax of "bootz" command is the same
4953 as the syntax of "bootm" command.
4955 Note, defining the CONFIG_SUPPORT_INITRD_RAW allows user to supply
4956 kernel with raw initrd images. The syntax is slightly different, the
4957 address of the initrd must be augmented by it's size, in the following
4958 format: "<initrd addres>:<initrd size>".
4964 One of the features of U-Boot is that you can dynamically load and
4965 run "standalone" applications, which can use some resources of
4966 U-Boot like console I/O functions or interrupt services.
4968 Two simple examples are included with the sources:
4973 'examples/hello_world.c' contains a small "Hello World" Demo
4974 application; it is automatically compiled when you build U-Boot.
4975 It's configured to run at address 0x00040004, so you can play with it
4979 ## Ready for S-Record download ...
4980 ~>examples/hello_world.srec
4981 1 2 3 4 5 6 7 8 9 10 11 ...
4982 [file transfer complete]
4984 ## Start Addr = 0x00040004
4986 => go 40004 Hello World! This is a test.
4987 ## Starting application at 0x00040004 ...
4998 Hit any key to exit ...
5000 ## Application terminated, rc = 0x0
5002 Another example, which demonstrates how to register a CPM interrupt
5003 handler with the U-Boot code, can be found in 'examples/timer.c'.
5004 Here, a CPM timer is set up to generate an interrupt every second.
5005 The interrupt service routine is trivial, just printing a '.'
5006 character, but this is just a demo program. The application can be
5007 controlled by the following keys:
5009 ? - print current values og the CPM Timer registers
5010 b - enable interrupts and start timer
5011 e - stop timer and disable interrupts
5012 q - quit application
5015 ## Ready for S-Record download ...
5016 ~>examples/timer.srec
5017 1 2 3 4 5 6 7 8 9 10 11 ...
5018 [file transfer complete]
5020 ## Start Addr = 0x00040004
5023 ## Starting application at 0x00040004 ...
5026 tgcr @ 0xfff00980, tmr @ 0xfff00990, trr @ 0xfff00994, tcr @ 0xfff00998, tcn @ 0xfff0099c, ter @ 0xfff009b0
5029 [q, b, e, ?] Set interval 1000000 us
5032 [q, b, e, ?] ........
5033 tgcr=0x1, tmr=0xff1c, trr=0x3d09, tcr=0x0, tcn=0xef6, ter=0x0
5036 tgcr=0x1, tmr=0xff1c, trr=0x3d09, tcr=0x0, tcn=0x2ad4, ter=0x0
5039 tgcr=0x1, tmr=0xff1c, trr=0x3d09, tcr=0x0, tcn=0x1efc, ter=0x0
5042 tgcr=0x1, tmr=0xff1c, trr=0x3d09, tcr=0x0, tcn=0x169d, ter=0x0
5044 [q, b, e, ?] ...Stopping timer
5046 [q, b, e, ?] ## Application terminated, rc = 0x0
5052 Over time, many people have reported problems when trying to use the
5053 "minicom" terminal emulation program for serial download. I (wd)
5054 consider minicom to be broken, and recommend not to use it. Under
5055 Unix, I recommend to use C-Kermit for general purpose use (and
5056 especially for kermit binary protocol download ("loadb" command), and
5057 use "cu" for S-Record download ("loads" command). See
5058 http://www.denx.de/wiki/view/DULG/SystemSetup#Section_4.3.
5059 for help with kermit.
5062 Nevertheless, if you absolutely want to use it try adding this
5063 configuration to your "File transfer protocols" section:
5065 Name Program Name U/D FullScr IO-Red. Multi
5066 X kermit /usr/bin/kermit -i -l %l -s Y U Y N N
5067 Y kermit /usr/bin/kermit -i -l %l -r N D Y N N
5073 Starting at version 0.9.2, U-Boot supports NetBSD both as host
5074 (build U-Boot) and target system (boots NetBSD/mpc8xx).
5076 Building requires a cross environment; it is known to work on
5077 NetBSD/i386 with the cross-powerpc-netbsd-1.3 package (you will also
5078 need gmake since the Makefiles are not compatible with BSD make).
5079 Note that the cross-powerpc package does not install include files;
5080 attempting to build U-Boot will fail because <machine/ansi.h> is
5081 missing. This file has to be installed and patched manually:
5083 # cd /usr/pkg/cross/powerpc-netbsd/include
5085 # ln -s powerpc machine
5086 # cp /usr/src/sys/arch/powerpc/include/ansi.h powerpc/ansi.h
5087 # ${EDIT} powerpc/ansi.h ## must remove __va_list, _BSD_VA_LIST
5089 Native builds *don't* work due to incompatibilities between native
5090 and U-Boot include files.
5092 Booting assumes that (the first part of) the image booted is a
5093 stage-2 loader which in turn loads and then invokes the kernel
5094 proper. Loader sources will eventually appear in the NetBSD source
5095 tree (probably in sys/arc/mpc8xx/stand/u-boot_stage2/); in the
5096 meantime, see ftp://ftp.denx.de/pub/u-boot/ppcboot_stage2.tar.gz
5099 Implementation Internals:
5100 =========================
5102 The following is not intended to be a complete description of every
5103 implementation detail. However, it should help to understand the
5104 inner workings of U-Boot and make it easier to port it to custom
5108 Initial Stack, Global Data:
5109 ---------------------------
5111 The implementation of U-Boot is complicated by the fact that U-Boot
5112 starts running out of ROM (flash memory), usually without access to
5113 system RAM (because the memory controller is not initialized yet).
5114 This means that we don't have writable Data or BSS segments, and BSS
5115 is not initialized as zero. To be able to get a C environment working
5116 at all, we have to allocate at least a minimal stack. Implementation
5117 options for this are defined and restricted by the CPU used: Some CPU
5118 models provide on-chip memory (like the IMMR area on MPC8xx and
5119 MPC826x processors), on others (parts of) the data cache can be
5120 locked as (mis-) used as memory, etc.
5122 Chris Hallinan posted a good summary of these issues to the
5123 U-Boot mailing list:
5125 Subject: RE: [U-Boot-Users] RE: More On Memory Bank x (nothingness)?
5126 From: "Chris Hallinan" <clh@net1plus.com>
5127 Date: Mon, 10 Feb 2003 16:43:46 -0500 (22:43 MET)
5130 Correct me if I'm wrong, folks, but the way I understand it
5131 is this: Using DCACHE as initial RAM for Stack, etc, does not
5132 require any physical RAM backing up the cache. The cleverness
5133 is that the cache is being used as a temporary supply of
5134 necessary storage before the SDRAM controller is setup. It's
5135 beyond the scope of this list to explain the details, but you
5136 can see how this works by studying the cache architecture and
5137 operation in the architecture and processor-specific manuals.
5139 OCM is On Chip Memory, which I believe the 405GP has 4K. It
5140 is another option for the system designer to use as an
5141 initial stack/RAM area prior to SDRAM being available. Either
5142 option should work for you. Using CS 4 should be fine if your
5143 board designers haven't used it for something that would
5144 cause you grief during the initial boot! It is frequently not
5147 CONFIG_SYS_INIT_RAM_ADDR should be somewhere that won't interfere
5148 with your processor/board/system design. The default value
5149 you will find in any recent u-boot distribution in
5150 walnut.h should work for you. I'd set it to a value larger
5151 than your SDRAM module. If you have a 64MB SDRAM module, set
5152 it above 400_0000. Just make sure your board has no resources
5153 that are supposed to respond to that address! That code in
5154 start.S has been around a while and should work as is when
5155 you get the config right.
5160 It is essential to remember this, since it has some impact on the C
5161 code for the initialization procedures:
5163 * Initialized global data (data segment) is read-only. Do not attempt
5166 * Do not use any uninitialized global data (or implicitely initialized
5167 as zero data - BSS segment) at all - this is undefined, initiali-
5168 zation is performed later (when relocating to RAM).
5170 * Stack space is very limited. Avoid big data buffers or things like
5173 Having only the stack as writable memory limits means we cannot use
5174 normal global data to share information beween the code. But it
5175 turned out that the implementation of U-Boot can be greatly
5176 simplified by making a global data structure (gd_t) available to all
5177 functions. We could pass a pointer to this data as argument to _all_
5178 functions, but this would bloat the code. Instead we use a feature of
5179 the GCC compiler (Global Register Variables) to share the data: we
5180 place a pointer (gd) to the global data into a register which we
5181 reserve for this purpose.
5183 When choosing a register for such a purpose we are restricted by the
5184 relevant (E)ABI specifications for the current architecture, and by
5185 GCC's implementation.
5187 For PowerPC, the following registers have specific use:
5189 R2: reserved for system use
5190 R3-R4: parameter passing and return values
5191 R5-R10: parameter passing
5192 R13: small data area pointer
5196 (U-Boot also uses R12 as internal GOT pointer. r12
5197 is a volatile register so r12 needs to be reset when
5198 going back and forth between asm and C)
5200 ==> U-Boot will use R2 to hold a pointer to the global data
5202 Note: on PPC, we could use a static initializer (since the
5203 address of the global data structure is known at compile time),
5204 but it turned out that reserving a register results in somewhat
5205 smaller code - although the code savings are not that big (on
5206 average for all boards 752 bytes for the whole U-Boot image,
5207 624 text + 127 data).
5209 On Blackfin, the normal C ABI (except for P3) is followed as documented here:
5210 http://docs.blackfin.uclinux.org/doku.php?id=application_binary_interface
5212 ==> U-Boot will use P3 to hold a pointer to the global data
5214 On ARM, the following registers are used:
5216 R0: function argument word/integer result
5217 R1-R3: function argument word
5219 R10: stack limit (used only if stack checking if enabled)
5220 R11: argument (frame) pointer
5221 R12: temporary workspace
5224 R15: program counter
5226 ==> U-Boot will use R8 to hold a pointer to the global data
5228 On Nios II, the ABI is documented here:
5229 http://www.altera.com/literature/hb/nios2/n2cpu_nii51016.pdf
5231 ==> U-Boot will use gp to hold a pointer to the global data
5233 Note: on Nios II, we give "-G0" option to gcc and don't use gp
5234 to access small data sections, so gp is free.
5236 On NDS32, the following registers are used:
5238 R0-R1: argument/return
5240 R15: temporary register for assembler
5241 R16: trampoline register
5242 R28: frame pointer (FP)
5243 R29: global pointer (GP)
5244 R30: link register (LP)
5245 R31: stack pointer (SP)
5246 PC: program counter (PC)
5248 ==> U-Boot will use R10 to hold a pointer to the global data
5250 NOTE: DECLARE_GLOBAL_DATA_PTR must be used with file-global scope,
5251 or current versions of GCC may "optimize" the code too much.
5256 U-Boot runs in system state and uses physical addresses, i.e. the
5257 MMU is not used either for address mapping nor for memory protection.
5259 The available memory is mapped to fixed addresses using the memory
5260 controller. In this process, a contiguous block is formed for each
5261 memory type (Flash, SDRAM, SRAM), even when it consists of several
5262 physical memory banks.
5264 U-Boot is installed in the first 128 kB of the first Flash bank (on
5265 TQM8xxL modules this is the range 0x40000000 ... 0x4001FFFF). After
5266 booting and sizing and initializing DRAM, the code relocates itself
5267 to the upper end of DRAM. Immediately below the U-Boot code some
5268 memory is reserved for use by malloc() [see CONFIG_SYS_MALLOC_LEN
5269 configuration setting]. Below that, a structure with global Board
5270 Info data is placed, followed by the stack (growing downward).
5272 Additionally, some exception handler code is copied to the low 8 kB
5273 of DRAM (0x00000000 ... 0x00001FFF).
5275 So a typical memory configuration with 16 MB of DRAM could look like
5278 0x0000 0000 Exception Vector code
5281 0x0000 2000 Free for Application Use
5287 0x00FB FF20 Monitor Stack (Growing downward)
5288 0x00FB FFAC Board Info Data and permanent copy of global data
5289 0x00FC 0000 Malloc Arena
5292 0x00FE 0000 RAM Copy of Monitor Code
5293 ... eventually: LCD or video framebuffer
5294 ... eventually: pRAM (Protected RAM - unchanged by reset)
5295 0x00FF FFFF [End of RAM]
5298 System Initialization:
5299 ----------------------
5301 In the reset configuration, U-Boot starts at the reset entry point
5302 (on most PowerPC systems at address 0x00000100). Because of the reset
5303 configuration for CS0# this is a mirror of the onboard Flash memory.
5304 To be able to re-map memory U-Boot then jumps to its link address.
5305 To be able to implement the initialization code in C, a (small!)
5306 initial stack is set up in the internal Dual Ported RAM (in case CPUs
5307 which provide such a feature like MPC8xx or MPC8260), or in a locked
5308 part of the data cache. After that, U-Boot initializes the CPU core,
5309 the caches and the SIU.
5311 Next, all (potentially) available memory banks are mapped using a
5312 preliminary mapping. For example, we put them on 512 MB boundaries
5313 (multiples of 0x20000000: SDRAM on 0x00000000 and 0x20000000, Flash
5314 on 0x40000000 and 0x60000000, SRAM on 0x80000000). Then UPM A is
5315 programmed for SDRAM access. Using the temporary configuration, a
5316 simple memory test is run that determines the size of the SDRAM
5319 When there is more than one SDRAM bank, and the banks are of
5320 different size, the largest is mapped first. For equal size, the first
5321 bank (CS2#) is mapped first. The first mapping is always for address
5322 0x00000000, with any additional banks following immediately to create
5323 contiguous memory starting from 0.
5325 Then, the monitor installs itself at the upper end of the SDRAM area
5326 and allocates memory for use by malloc() and for the global Board
5327 Info data; also, the exception vector code is copied to the low RAM
5328 pages, and the final stack is set up.
5330 Only after this relocation will you have a "normal" C environment;
5331 until that you are restricted in several ways, mostly because you are
5332 running from ROM, and because the code will have to be relocated to a
5336 U-Boot Porting Guide:
5337 ----------------------
5339 [Based on messages by Jerry Van Baren in the U-Boot-Users mailing
5343 int main(int argc, char *argv[])
5345 sighandler_t no_more_time;
5347 signal(SIGALRM, no_more_time);
5348 alarm(PROJECT_DEADLINE - toSec (3 * WEEK));
5350 if (available_money > available_manpower) {
5351 Pay consultant to port U-Boot;
5355 Download latest U-Boot source;
5357 Subscribe to u-boot mailing list;
5360 email("Hi, I am new to U-Boot, how do I get started?");
5363 Read the README file in the top level directory;
5364 Read http://www.denx.de/twiki/bin/view/DULG/Manual;
5365 Read applicable doc/*.README;
5366 Read the source, Luke;
5367 /* find . -name "*.[chS]" | xargs grep -i <keyword> */
5370 if (available_money > toLocalCurrency ($2500))
5373 Add a lot of aggravation and time;
5375 if (a similar board exists) { /* hopefully... */
5376 cp -a board/<similar> board/<myboard>
5377 cp include/configs/<similar>.h include/configs/<myboard>.h
5379 Create your own board support subdirectory;
5380 Create your own board include/configs/<myboard>.h file;
5382 Edit new board/<myboard> files
5383 Edit new include/configs/<myboard>.h
5388 Add / modify source code;
5392 email("Hi, I am having problems...");
5394 Send patch file to the U-Boot email list;
5395 if (reasonable critiques)
5396 Incorporate improvements from email list code review;
5398 Defend code as written;
5404 void no_more_time (int sig)
5413 All contributions to U-Boot should conform to the Linux kernel
5414 coding style; see the file "Documentation/CodingStyle" and the script
5415 "scripts/Lindent" in your Linux kernel source directory.
5417 Source files originating from a different project (for example the
5418 MTD subsystem) are generally exempt from these guidelines and are not
5419 reformated to ease subsequent migration to newer versions of those
5422 Please note that U-Boot is implemented in C (and to some small parts in
5423 Assembler); no C++ is used, so please do not use C++ style comments (//)
5426 Please also stick to the following formatting rules:
5427 - remove any trailing white space
5428 - use TAB characters for indentation and vertical alignment, not spaces
5429 - make sure NOT to use DOS '\r\n' line feeds
5430 - do not add more than 2 consecutive empty lines to source files
5431 - do not add trailing empty lines to source files
5433 Submissions which do not conform to the standards may be returned
5434 with a request to reformat the changes.
5440 Since the number of patches for U-Boot is growing, we need to
5441 establish some rules. Submissions which do not conform to these rules
5442 may be rejected, even when they contain important and valuable stuff.
5444 Please see http://www.denx.de/wiki/U-Boot/Patches for details.
5446 Patches shall be sent to the u-boot mailing list <u-boot@lists.denx.de>;
5447 see http://lists.denx.de/mailman/listinfo/u-boot
5449 When you send a patch, please include the following information with
5452 * For bug fixes: a description of the bug and how your patch fixes
5453 this bug. Please try to include a way of demonstrating that the
5454 patch actually fixes something.
5456 * For new features: a description of the feature and your
5459 * A CHANGELOG entry as plaintext (separate from the patch)
5461 * For major contributions, your entry to the CREDITS file
5463 * When you add support for a new board, don't forget to add this
5464 board to the MAINTAINERS file, too.
5466 * If your patch adds new configuration options, don't forget to
5467 document these in the README file.
5469 * The patch itself. If you are using git (which is *strongly*
5470 recommended) you can easily generate the patch using the
5471 "git format-patch". If you then use "git send-email" to send it to
5472 the U-Boot mailing list, you will avoid most of the common problems
5473 with some other mail clients.
5475 If you cannot use git, use "diff -purN OLD NEW". If your version of
5476 diff does not support these options, then get the latest version of
5479 The current directory when running this command shall be the parent
5480 directory of the U-Boot source tree (i. e. please make sure that
5481 your patch includes sufficient directory information for the
5484 We prefer patches as plain text. MIME attachments are discouraged,
5485 and compressed attachments must not be used.
5487 * If one logical set of modifications affects or creates several
5488 files, all these changes shall be submitted in a SINGLE patch file.
5490 * Changesets that contain different, unrelated modifications shall be
5491 submitted as SEPARATE patches, one patch per changeset.
5496 * Before sending the patch, run the MAKEALL script on your patched
5497 source tree and make sure that no errors or warnings are reported
5498 for any of the boards.
5500 * Keep your modifications to the necessary minimum: A patch
5501 containing several unrelated changes or arbitrary reformats will be
5502 returned with a request to re-formatting / split it.
5504 * If you modify existing code, make sure that your new code does not
5505 add to the memory footprint of the code ;-) Small is beautiful!
5506 When adding new features, these should compile conditionally only
5507 (using #ifdef), and the resulting code with the new feature
5508 disabled must not need more memory than the old code without your
5511 * Remember that there is a size limit of 100 kB per message on the
5512 u-boot mailing list. Bigger patches will be moderated. If they are
5513 reasonable and not too big, they will be acknowledged. But patches
5514 bigger than the size limit should be avoided.