2 # (C) Copyright 2000 - 2012
3 # Wolfgang Denk, DENX Software Engineering, wd@denx.de.
5 # See file CREDITS for list of people who contributed to this
8 # This program is free software; you can redistribute it and/or
9 # modify it under the terms of the GNU General Public License as
10 # published by the Free Software Foundation; either version 2 of
11 # the License, or (at your option) any later version.
13 # This program is distributed in the hope that it will be useful,
14 # but WITHOUT ANY WARRANTY; without even the implied warranty of
15 # MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the
16 # GNU General Public License for more details.
18 # You should have received a copy of the GNU General Public License
19 # along with this program; if not, write to the Free Software
20 # Foundation, Inc., 59 Temple Place, Suite 330, Boston,
27 This directory contains the source code for U-Boot, a boot loader for
28 Embedded boards based on PowerPC, ARM, MIPS and several other
29 processors, which can be installed in a boot ROM and used to
30 initialize and test the hardware or to download and run application
33 The development of U-Boot is closely related to Linux: some parts of
34 the source code originate in the Linux source tree, we have some
35 header files in common, and special provision has been made to
36 support booting of Linux images.
38 Some attention has been paid to make this software easily
39 configurable and extendable. For instance, all monitor commands are
40 implemented with the same call interface, so that it's very easy to
41 add new commands. Also, instead of permanently adding rarely used
42 code (for instance hardware test utilities) to the monitor, you can
43 load and run it dynamically.
49 In general, all boards for which a configuration option exists in the
50 Makefile have been tested to some extent and can be considered
51 "working". In fact, many of them are used in production systems.
53 In case of problems see the CHANGELOG and CREDITS files to find out
54 who contributed the specific port. The MAINTAINERS file lists board
57 Note: There is no CHANGELOG file in the actual U-Boot source tree;
58 it can be created dynamically from the Git log using:
66 In case you have questions about, problems with or contributions for
67 U-Boot you should send a message to the U-Boot mailing list at
68 <u-boot@lists.denx.de>. There is also an archive of previous traffic
69 on the mailing list - please search the archive before asking FAQ's.
70 Please see http://lists.denx.de/pipermail/u-boot and
71 http://dir.gmane.org/gmane.comp.boot-loaders.u-boot
74 Where to get source code:
75 =========================
77 The U-Boot source code is maintained in the git repository at
78 git://www.denx.de/git/u-boot.git ; you can browse it online at
79 http://www.denx.de/cgi-bin/gitweb.cgi?p=u-boot.git;a=summary
81 The "snapshot" links on this page allow you to download tarballs of
82 any version you might be interested in. Official releases are also
83 available for FTP download from the ftp://ftp.denx.de/pub/u-boot/
86 Pre-built (and tested) images are available from
87 ftp://ftp.denx.de/pub/u-boot/images/
93 - start from 8xxrom sources
94 - create PPCBoot project (http://sourceforge.net/projects/ppcboot)
96 - make it easier to add custom boards
97 - make it possible to add other [PowerPC] CPUs
98 - extend functions, especially:
99 * Provide extended interface to Linux boot loader
102 * PCMCIA / CompactFlash / ATA disk / SCSI ... boot
103 - create ARMBoot project (http://sourceforge.net/projects/armboot)
104 - add other CPU families (starting with ARM)
105 - create U-Boot project (http://sourceforge.net/projects/u-boot)
106 - current project page: see http://www.denx.de/wiki/U-Boot
112 The "official" name of this project is "Das U-Boot". The spelling
113 "U-Boot" shall be used in all written text (documentation, comments
114 in source files etc.). Example:
116 This is the README file for the U-Boot project.
118 File names etc. shall be based on the string "u-boot". Examples:
120 include/asm-ppc/u-boot.h
122 #include <asm/u-boot.h>
124 Variable names, preprocessor constants etc. shall be either based on
125 the string "u_boot" or on "U_BOOT". Example:
127 U_BOOT_VERSION u_boot_logo
128 IH_OS_U_BOOT u_boot_hush_start
134 Starting with the release in October 2008, the names of the releases
135 were changed from numerical release numbers without deeper meaning
136 into a time stamp based numbering. Regular releases are identified by
137 names consisting of the calendar year and month of the release date.
138 Additional fields (if present) indicate release candidates or bug fix
139 releases in "stable" maintenance trees.
142 U-Boot v2009.11 - Release November 2009
143 U-Boot v2009.11.1 - Release 1 in version November 2009 stable tree
144 U-Boot v2010.09-rc1 - Release candiate 1 for September 2010 release
150 /arch Architecture specific files
151 /arm Files generic to ARM architecture
152 /cpu CPU specific files
153 /arm720t Files specific to ARM 720 CPUs
154 /arm920t Files specific to ARM 920 CPUs
155 /at91 Files specific to Atmel AT91RM9200 CPU
156 /imx Files specific to Freescale MC9328 i.MX CPUs
157 /s3c24x0 Files specific to Samsung S3C24X0 CPUs
158 /arm925t Files specific to ARM 925 CPUs
159 /arm926ejs Files specific to ARM 926 CPUs
160 /arm1136 Files specific to ARM 1136 CPUs
161 /ixp Files specific to Intel XScale IXP CPUs
162 /pxa Files specific to Intel XScale PXA CPUs
163 /s3c44b0 Files specific to Samsung S3C44B0 CPUs
164 /sa1100 Files specific to Intel StrongARM SA1100 CPUs
165 /lib Architecture specific library files
166 /avr32 Files generic to AVR32 architecture
167 /cpu CPU specific files
168 /lib Architecture specific library files
169 /blackfin Files generic to Analog Devices Blackfin architecture
170 /cpu CPU specific files
171 /lib Architecture specific library files
172 /x86 Files generic to x86 architecture
173 /cpu CPU specific files
174 /lib Architecture specific library files
175 /m68k Files generic to m68k architecture
176 /cpu CPU specific files
177 /mcf52x2 Files specific to Freescale ColdFire MCF52x2 CPUs
178 /mcf5227x Files specific to Freescale ColdFire MCF5227x CPUs
179 /mcf532x Files specific to Freescale ColdFire MCF5329 CPUs
180 /mcf5445x Files specific to Freescale ColdFire MCF5445x CPUs
181 /mcf547x_8x Files specific to Freescale ColdFire MCF547x_8x CPUs
182 /lib Architecture specific library files
183 /microblaze Files generic to microblaze architecture
184 /cpu CPU specific files
185 /lib Architecture specific library files
186 /mips Files generic to MIPS architecture
187 /cpu CPU specific files
188 /mips32 Files specific to MIPS32 CPUs
189 /xburst Files specific to Ingenic XBurst CPUs
190 /lib Architecture specific library files
191 /nds32 Files generic to NDS32 architecture
192 /cpu CPU specific files
193 /n1213 Files specific to Andes Technology N1213 CPUs
194 /lib Architecture specific library files
195 /nios2 Files generic to Altera NIOS2 architecture
196 /cpu CPU specific files
197 /lib Architecture specific library files
198 /powerpc Files generic to PowerPC architecture
199 /cpu CPU specific files
200 /74xx_7xx Files specific to Freescale MPC74xx and 7xx CPUs
201 /mpc5xx Files specific to Freescale MPC5xx CPUs
202 /mpc5xxx Files specific to Freescale MPC5xxx CPUs
203 /mpc8xx Files specific to Freescale MPC8xx CPUs
204 /mpc8220 Files specific to Freescale MPC8220 CPUs
205 /mpc824x Files specific to Freescale MPC824x CPUs
206 /mpc8260 Files specific to Freescale MPC8260 CPUs
207 /mpc85xx Files specific to Freescale MPC85xx CPUs
208 /ppc4xx Files specific to AMCC PowerPC 4xx CPUs
209 /lib Architecture specific library files
210 /sh Files generic to SH architecture
211 /cpu CPU specific files
212 /sh2 Files specific to sh2 CPUs
213 /sh3 Files specific to sh3 CPUs
214 /sh4 Files specific to sh4 CPUs
215 /lib Architecture specific library files
216 /sparc Files generic to SPARC architecture
217 /cpu CPU specific files
218 /leon2 Files specific to Gaisler LEON2 SPARC CPU
219 /leon3 Files specific to Gaisler LEON3 SPARC CPU
220 /lib Architecture specific library files
221 /api Machine/arch independent API for external apps
222 /board Board dependent files
223 /common Misc architecture independent functions
224 /disk Code for disk drive partition handling
225 /doc Documentation (don't expect too much)
226 /drivers Commonly used device drivers
227 /examples Example code for standalone applications, etc.
228 /fs Filesystem code (cramfs, ext2, jffs2, etc.)
229 /include Header Files
230 /lib Files generic to all architectures
231 /libfdt Library files to support flattened device trees
232 /lzma Library files to support LZMA decompression
233 /lzo Library files to support LZO decompression
235 /post Power On Self Test
236 /rtc Real Time Clock drivers
237 /tools Tools to build S-Record or U-Boot images, etc.
239 Software Configuration:
240 =======================
242 Configuration is usually done using C preprocessor defines; the
243 rationale behind that is to avoid dead code whenever possible.
245 There are two classes of configuration variables:
247 * Configuration _OPTIONS_:
248 These are selectable by the user and have names beginning with
251 * Configuration _SETTINGS_:
252 These depend on the hardware etc. and should not be meddled with if
253 you don't know what you're doing; they have names beginning with
256 Later we will add a configuration tool - probably similar to or even
257 identical to what's used for the Linux kernel. Right now, we have to
258 do the configuration by hand, which means creating some symbolic
259 links and editing some configuration files. We use the TQM8xxL boards
263 Selection of Processor Architecture and Board Type:
264 ---------------------------------------------------
266 For all supported boards there are ready-to-use default
267 configurations available; just type "make <board_name>_config".
269 Example: For a TQM823L module type:
274 For the Cogent platform, you need to specify the CPU type as well;
275 e.g. "make cogent_mpc8xx_config". And also configure the cogent
276 directory according to the instructions in cogent/README.
279 Configuration Options:
280 ----------------------
282 Configuration depends on the combination of board and CPU type; all
283 such information is kept in a configuration file
284 "include/configs/<board_name>.h".
286 Example: For a TQM823L module, all configuration settings are in
287 "include/configs/TQM823L.h".
290 Many of the options are named exactly as the corresponding Linux
291 kernel configuration options. The intention is to make it easier to
292 build a config tool - later.
295 The following options need to be configured:
297 - CPU Type: Define exactly one, e.g. CONFIG_MPC85XX.
299 - Board Type: Define exactly one, e.g. CONFIG_MPC8540ADS.
301 - CPU Daughterboard Type: (if CONFIG_ATSTK1000 is defined)
302 Define exactly one, e.g. CONFIG_ATSTK1002
304 - CPU Module Type: (if CONFIG_COGENT is defined)
305 Define exactly one of
307 --- FIXME --- not tested yet:
308 CONFIG_CMA286_60, CONFIG_CMA286_21, CONFIG_CMA286_60P,
309 CONFIG_CMA287_23, CONFIG_CMA287_50
311 - Motherboard Type: (if CONFIG_COGENT is defined)
312 Define exactly one of
313 CONFIG_CMA101, CONFIG_CMA102
315 - Motherboard I/O Modules: (if CONFIG_COGENT is defined)
316 Define one or more of
319 - Motherboard Options: (if CONFIG_CMA101 or CONFIG_CMA102 are defined)
320 Define one or more of
321 CONFIG_LCD_HEARTBEAT - update a character position on
322 the LCD display every second with
325 - Board flavour: (if CONFIG_MPC8260ADS is defined)
328 CONFIG_SYS_8260ADS - original MPC8260ADS
329 CONFIG_SYS_8266ADS - MPC8266ADS
330 CONFIG_SYS_PQ2FADS - PQ2FADS-ZU or PQ2FADS-VR
331 CONFIG_SYS_8272ADS - MPC8272ADS
333 - Marvell Family Member
334 CONFIG_SYS_MVFS - define it if you want to enable
335 multiple fs option at one time
336 for marvell soc family
338 - MPC824X Family Member (if CONFIG_MPC824X is defined)
339 Define exactly one of
340 CONFIG_MPC8240, CONFIG_MPC8245
342 - 8xx CPU Options: (if using an MPC8xx CPU)
343 CONFIG_8xx_GCLK_FREQ - deprecated: CPU clock if
344 get_gclk_freq() cannot work
345 e.g. if there is no 32KHz
346 reference PIT/RTC clock
347 CONFIG_8xx_OSCLK - PLL input clock (either EXTCLK
350 - 859/866/885 CPU options: (if using a MPC859 or MPC866 or MPC885 CPU):
351 CONFIG_SYS_8xx_CPUCLK_MIN
352 CONFIG_SYS_8xx_CPUCLK_MAX
353 CONFIG_8xx_CPUCLK_DEFAULT
354 See doc/README.MPC866
356 CONFIG_SYS_MEASURE_CPUCLK
358 Define this to measure the actual CPU clock instead
359 of relying on the correctness of the configured
360 values. Mostly useful for board bringup to make sure
361 the PLL is locked at the intended frequency. Note
362 that this requires a (stable) reference clock (32 kHz
363 RTC clock or CONFIG_SYS_8XX_XIN)
365 CONFIG_SYS_DELAYED_ICACHE
367 Define this option if you want to enable the
368 ICache only when Code runs from RAM.
373 Specifies that the core is a 64-bit PowerPC implementation (implements
374 the "64" category of the Power ISA). This is necessary for ePAPR
375 compliance, among other possible reasons.
377 CONFIG_SYS_FSL_TBCLK_DIV
379 Defines the core time base clock divider ratio compared to the
380 system clock. On most PQ3 devices this is 8, on newer QorIQ
381 devices it can be 16 or 32. The ratio varies from SoC to Soc.
383 CONFIG_SYS_FSL_PCIE_COMPAT
385 Defines the string to utilize when trying to match PCIe device
386 tree nodes for the given platform.
388 CONFIG_SYS_PPC_E500_DEBUG_TLB
390 Enables a temporary TLB entry to be used during boot to work
391 around limitations in e500v1 and e500v2 external debugger
392 support. This reduces the portions of the boot code where
393 breakpoints and single stepping do not work. The value of this
394 symbol should be set to the TLB1 entry to be used for this
397 CONFIG_SYS_FSL_ERRATUM_A004510
399 Enables a workaround for erratum A004510. If set,
400 then CONFIG_SYS_FSL_ERRATUM_A004510_SVR_REV and
401 CONFIG_SYS_FSL_CORENET_SNOOPVEC_COREONLY must be set.
403 CONFIG_SYS_FSL_ERRATUM_A004510_SVR_REV
404 CONFIG_SYS_FSL_ERRATUM_A004510_SVR_REV2 (optional)
406 Defines one or two SoC revisions (low 8 bits of SVR)
407 for which the A004510 workaround should be applied.
409 The rest of SVR is either not relevant to the decision
410 of whether the erratum is present (e.g. p2040 versus
411 p2041) or is implied by the build target, which controls
412 whether CONFIG_SYS_FSL_ERRATUM_A004510 is set.
414 See Freescale App Note 4493 for more information about
417 CONFIG_SYS_FSL_CORENET_SNOOPVEC_COREONLY
419 This is the value to write into CCSR offset 0x18600
420 according to the A004510 workaround.
422 - Generic CPU options:
423 CONFIG_SYS_BIG_ENDIAN, CONFIG_SYS_LITTLE_ENDIAN
425 Defines the endianess of the CPU. Implementation of those
426 values is arch specific.
428 - Intel Monahans options:
429 CONFIG_SYS_MONAHANS_RUN_MODE_OSC_RATIO
431 Defines the Monahans run mode to oscillator
432 ratio. Valid values are 8, 16, 24, 31. The core
433 frequency is this value multiplied by 13 MHz.
435 CONFIG_SYS_MONAHANS_TURBO_RUN_MODE_RATIO
437 Defines the Monahans turbo mode to oscillator
438 ratio. Valid values are 1 (default if undefined) and
439 2. The core frequency as calculated above is multiplied
443 CONFIG_SYS_INIT_SP_OFFSET
445 Offset relative to CONFIG_SYS_SDRAM_BASE for initial stack
446 pointer. This is needed for the temporary stack before
449 CONFIG_SYS_MIPS_CACHE_MODE
451 Cache operation mode for the MIPS CPU.
452 See also arch/mips/include/asm/mipsregs.h.
454 CONF_CM_CACHABLE_NO_WA
457 CONF_CM_CACHABLE_NONCOHERENT
461 CONF_CM_CACHABLE_ACCELERATED
463 CONFIG_SYS_XWAY_EBU_BOOTCFG
465 Special option for Lantiq XWAY SoCs for booting from NOR flash.
466 See also arch/mips/cpu/mips32/start.S.
468 CONFIG_XWAY_SWAP_BYTES
470 Enable compilation of tools/xway-swap-bytes needed for Lantiq
471 XWAY SoCs for booting from NOR flash. The U-Boot image needs to
472 be swapped if a flash programmer is used.
475 CONFIG_SYS_EXCEPTION_VECTORS_HIGH
477 Select high exception vectors of the ARM core, e.g., do not
478 clear the V bit of the c1 register of CP15.
480 CONFIG_SYS_THUMB_BUILD
482 Use this flag to build U-Boot using the Thumb instruction
483 set for ARM architectures. Thumb instruction set provides
484 better code density. For ARM architectures that support
485 Thumb2 this flag will result in Thumb2 code generated by
488 CONFIG_ARM_ERRATA_716044
489 CONFIG_ARM_ERRATA_742230
490 CONFIG_ARM_ERRATA_743622
491 CONFIG_ARM_ERRATA_751472
493 If set, the workarounds for these ARM errata are applied early
494 during U-Boot startup. Note that these options force the
495 workarounds to be applied; no CPU-type/version detection
496 exists, unlike the similar options in the Linux kernel. Do not
497 set these options unless they apply!
502 The frequency of the timer returned by get_timer().
503 get_timer() must operate in milliseconds and this CONFIG
504 option must be set to 1000.
506 - Linux Kernel Interface:
509 U-Boot stores all clock information in Hz
510 internally. For binary compatibility with older Linux
511 kernels (which expect the clocks passed in the
512 bd_info data to be in MHz) the environment variable
513 "clocks_in_mhz" can be defined so that U-Boot
514 converts clock data to MHZ before passing it to the
516 When CONFIG_CLOCKS_IN_MHZ is defined, a definition of
517 "clocks_in_mhz=1" is automatically included in the
520 CONFIG_MEMSIZE_IN_BYTES [relevant for MIPS only]
522 When transferring memsize parameter to linux, some versions
523 expect it to be in bytes, others in MB.
524 Define CONFIG_MEMSIZE_IN_BYTES to make it in bytes.
528 New kernel versions are expecting firmware settings to be
529 passed using flattened device trees (based on open firmware
533 * New libfdt-based support
534 * Adds the "fdt" command
535 * The bootm command automatically updates the fdt
537 OF_CPU - The proper name of the cpus node (only required for
538 MPC512X and MPC5xxx based boards).
539 OF_SOC - The proper name of the soc node (only required for
540 MPC512X and MPC5xxx based boards).
541 OF_TBCLK - The timebase frequency.
542 OF_STDOUT_PATH - The path to the console device
544 boards with QUICC Engines require OF_QE to set UCC MAC
547 CONFIG_OF_BOARD_SETUP
549 Board code has addition modification that it wants to make
550 to the flat device tree before handing it off to the kernel
554 This define fills in the correct boot CPU in the boot
555 param header, the default value is zero if undefined.
559 U-Boot can detect if an IDE device is present or not.
560 If not, and this new config option is activated, U-Boot
561 removes the ATA node from the DTS before booting Linux,
562 so the Linux IDE driver does not probe the device and
563 crash. This is needed for buggy hardware (uc101) where
564 no pull down resistor is connected to the signal IDE5V_DD7.
566 CONFIG_MACH_TYPE [relevant for ARM only][mandatory]
568 This setting is mandatory for all boards that have only one
569 machine type and must be used to specify the machine type
570 number as it appears in the ARM machine registry
571 (see http://www.arm.linux.org.uk/developer/machines/).
572 Only boards that have multiple machine types supported
573 in a single configuration file and the machine type is
574 runtime discoverable, do not have to use this setting.
576 - vxWorks boot parameters:
578 bootvx constructs a valid bootline using the following
579 environments variables: bootfile, ipaddr, serverip, hostname.
580 It loads the vxWorks image pointed bootfile.
582 CONFIG_SYS_VXWORKS_BOOT_DEVICE - The vxworks device name
583 CONFIG_SYS_VXWORKS_MAC_PTR - Ethernet 6 byte MA -address
584 CONFIG_SYS_VXWORKS_SERVERNAME - Name of the server
585 CONFIG_SYS_VXWORKS_BOOT_ADDR - Address of boot parameters
587 CONFIG_SYS_VXWORKS_ADD_PARAMS
589 Add it at the end of the bootline. E.g "u=username pw=secret"
591 Note: If a "bootargs" environment is defined, it will overwride
592 the defaults discussed just above.
594 - Cache Configuration:
595 CONFIG_SYS_ICACHE_OFF - Do not enable instruction cache in U-Boot
596 CONFIG_SYS_DCACHE_OFF - Do not enable data cache in U-Boot
597 CONFIG_SYS_L2CACHE_OFF- Do not enable L2 cache in U-Boot
599 - Cache Configuration for ARM:
600 CONFIG_SYS_L2_PL310 - Enable support for ARM PL310 L2 cache
602 CONFIG_SYS_PL310_BASE - Physical base address of PL310
603 controller register space
608 Define this if you want support for Amba PrimeCell PL010 UARTs.
612 Define this if you want support for Amba PrimeCell PL011 UARTs.
616 If you have Amba PrimeCell PL011 UARTs, set this variable to
617 the clock speed of the UARTs.
621 If you have Amba PrimeCell PL010 or PL011 UARTs on your board,
622 define this to a list of base addresses for each (supported)
623 port. See e.g. include/configs/versatile.h
625 CONFIG_PL011_SERIAL_RLCR
627 Some vendor versions of PL011 serial ports (e.g. ST-Ericsson U8500)
628 have separate receive and transmit line control registers. Set
629 this variable to initialize the extra register.
631 CONFIG_PL011_SERIAL_FLUSH_ON_INIT
633 On some platforms (e.g. U8500) U-Boot is loaded by a second stage
634 boot loader that has already initialized the UART. Define this
635 variable to flush the UART at init time.
637 CONFIG_SYS_NS16550_BROKEN_TEMT
639 16550 UART set the Transmitter Empty (TEMT) Bit when all output
640 has finished and the transmitter is totally empty. U-Boot waits
641 for this bit to be set to initialize the serial console. On some
642 broken platforms this bit is not set in SPL making U-Boot to
643 hang while waiting for TEMT. Define this option to avoid it.
647 Depending on board, define exactly one serial port
648 (like CONFIG_8xx_CONS_SMC1, CONFIG_8xx_CONS_SMC2,
649 CONFIG_8xx_CONS_SCC1, ...), or switch off the serial
650 console by defining CONFIG_8xx_CONS_NONE
652 Note: if CONFIG_8xx_CONS_NONE is defined, the serial
653 port routines must be defined elsewhere
654 (i.e. serial_init(), serial_getc(), ...)
657 Enables console device for a color framebuffer. Needs following
658 defines (cf. smiLynxEM, i8042)
659 VIDEO_FB_LITTLE_ENDIAN graphic memory organisation
661 VIDEO_HW_RECTFILL graphic chip supports
664 VIDEO_HW_BITBLT graphic chip supports
665 bit-blit (cf. smiLynxEM)
666 VIDEO_VISIBLE_COLS visible pixel columns
668 VIDEO_VISIBLE_ROWS visible pixel rows
669 VIDEO_PIXEL_SIZE bytes per pixel
670 VIDEO_DATA_FORMAT graphic data format
671 (0-5, cf. cfb_console.c)
672 VIDEO_FB_ADRS framebuffer address
673 VIDEO_KBD_INIT_FCT keyboard int fct
674 (i.e. i8042_kbd_init())
675 VIDEO_TSTC_FCT test char fct
677 VIDEO_GETC_FCT get char fct
679 CONFIG_CONSOLE_CURSOR cursor drawing on/off
680 (requires blink timer
682 CONFIG_SYS_CONSOLE_BLINK_COUNT blink interval (cf. i8042.c)
683 CONFIG_CONSOLE_TIME display time/date info in
685 (requires CONFIG_CMD_DATE)
686 CONFIG_VIDEO_LOGO display Linux logo in
688 CONFIG_VIDEO_BMP_LOGO use bmp_logo.h instead of
689 linux_logo.h for logo.
690 Requires CONFIG_VIDEO_LOGO
691 CONFIG_CONSOLE_EXTRA_INFO
692 additional board info beside
695 When CONFIG_CFB_CONSOLE_ANSI is defined, console will support
696 a limited number of ANSI escape sequences (cursor control,
697 erase functions and limited graphics rendition control).
699 When CONFIG_CFB_CONSOLE is defined, video console is
700 default i/o. Serial console can be forced with
701 environment 'console=serial'.
703 When CONFIG_SILENT_CONSOLE is defined, all console
704 messages (by U-Boot and Linux!) can be silenced with
705 the "silent" environment variable. See
706 doc/README.silent for more information.
709 CONFIG_BAUDRATE - in bps
710 Select one of the baudrates listed in
711 CONFIG_SYS_BAUDRATE_TABLE, see below.
712 CONFIG_SYS_BRGCLK_PRESCALE, baudrate prescale
714 - Console Rx buffer length
715 With CONFIG_SYS_SMC_RXBUFLEN it is possible to define
716 the maximum receive buffer length for the SMC.
717 This option is actual only for 82xx and 8xx possible.
718 If using CONFIG_SYS_SMC_RXBUFLEN also CONFIG_SYS_MAXIDLE
719 must be defined, to setup the maximum idle timeout for
722 - Pre-Console Buffer:
723 Prior to the console being initialised (i.e. serial UART
724 initialised etc) all console output is silently discarded.
725 Defining CONFIG_PRE_CONSOLE_BUFFER will cause U-Boot to
726 buffer any console messages prior to the console being
727 initialised to a buffer of size CONFIG_PRE_CON_BUF_SZ
728 bytes located at CONFIG_PRE_CON_BUF_ADDR. The buffer is
729 a circular buffer, so if more than CONFIG_PRE_CON_BUF_SZ
730 bytes are output before the console is initialised, the
731 earlier bytes are discarded.
733 'Sane' compilers will generate smaller code if
734 CONFIG_PRE_CON_BUF_SZ is a power of 2
736 - Safe printf() functions
737 Define CONFIG_SYS_VSNPRINTF to compile in safe versions of
738 the printf() functions. These are defined in
739 include/vsprintf.h and include snprintf(), vsnprintf() and
740 so on. Code size increase is approximately 300-500 bytes.
741 If this option is not given then these functions will
742 silently discard their buffer size argument - this means
743 you are not getting any overflow checking in this case.
745 - Boot Delay: CONFIG_BOOTDELAY - in seconds
746 Delay before automatically booting the default image;
747 set to -1 to disable autoboot.
748 set to -2 to autoboot with no delay and not check for abort
749 (even when CONFIG_ZERO_BOOTDELAY_CHECK is defined).
751 See doc/README.autoboot for these options that
752 work with CONFIG_BOOTDELAY. None are required.
753 CONFIG_BOOT_RETRY_TIME
754 CONFIG_BOOT_RETRY_MIN
755 CONFIG_AUTOBOOT_KEYED
756 CONFIG_AUTOBOOT_PROMPT
757 CONFIG_AUTOBOOT_DELAY_STR
758 CONFIG_AUTOBOOT_STOP_STR
759 CONFIG_AUTOBOOT_DELAY_STR2
760 CONFIG_AUTOBOOT_STOP_STR2
761 CONFIG_ZERO_BOOTDELAY_CHECK
762 CONFIG_RESET_TO_RETRY
766 Only needed when CONFIG_BOOTDELAY is enabled;
767 define a command string that is automatically executed
768 when no character is read on the console interface
769 within "Boot Delay" after reset.
772 This can be used to pass arguments to the bootm
773 command. The value of CONFIG_BOOTARGS goes into the
774 environment value "bootargs".
776 CONFIG_RAMBOOT and CONFIG_NFSBOOT
777 The value of these goes into the environment as
778 "ramboot" and "nfsboot" respectively, and can be used
779 as a convenience, when switching between booting from
785 When this option is #defined, the existence of the
786 environment variable "preboot" will be checked
787 immediately before starting the CONFIG_BOOTDELAY
788 countdown and/or running the auto-boot command resp.
789 entering interactive mode.
791 This feature is especially useful when "preboot" is
792 automatically generated or modified. For an example
793 see the LWMON board specific code: here "preboot" is
794 modified when the user holds down a certain
795 combination of keys on the (special) keyboard when
798 - Serial Download Echo Mode:
800 If defined to 1, all characters received during a
801 serial download (using the "loads" command) are
802 echoed back. This might be needed by some terminal
803 emulations (like "cu"), but may as well just take
804 time on others. This setting #define's the initial
805 value of the "loads_echo" environment variable.
807 - Kgdb Serial Baudrate: (if CONFIG_CMD_KGDB is defined)
809 Select one of the baudrates listed in
810 CONFIG_SYS_BAUDRATE_TABLE, see below.
813 Monitor commands can be included or excluded
814 from the build by using the #include files
815 <config_cmd_all.h> and #undef'ing unwanted
816 commands, or using <config_cmd_default.h>
817 and augmenting with additional #define's
820 The default command configuration includes all commands
821 except those marked below with a "*".
823 CONFIG_CMD_ASKENV * ask for env variable
824 CONFIG_CMD_BDI bdinfo
825 CONFIG_CMD_BEDBUG * Include BedBug Debugger
826 CONFIG_CMD_BMP * BMP support
827 CONFIG_CMD_BSP * Board specific commands
828 CONFIG_CMD_BOOTD bootd
829 CONFIG_CMD_CACHE * icache, dcache
830 CONFIG_CMD_CONSOLE coninfo
831 CONFIG_CMD_CRC32 * crc32
832 CONFIG_CMD_DATE * support for RTC, date/time...
833 CONFIG_CMD_DHCP * DHCP support
834 CONFIG_CMD_DIAG * Diagnostics
835 CONFIG_CMD_DS4510 * ds4510 I2C gpio commands
836 CONFIG_CMD_DS4510_INFO * ds4510 I2C info command
837 CONFIG_CMD_DS4510_MEM * ds4510 I2C eeprom/sram commansd
838 CONFIG_CMD_DS4510_RST * ds4510 I2C rst command
839 CONFIG_CMD_DTT * Digital Therm and Thermostat
840 CONFIG_CMD_ECHO echo arguments
841 CONFIG_CMD_EDITENV edit env variable
842 CONFIG_CMD_EEPROM * EEPROM read/write support
843 CONFIG_CMD_ELF * bootelf, bootvx
844 CONFIG_CMD_ENV_CALLBACK * display details about env callbacks
845 CONFIG_CMD_ENV_FLAGS * display details about env flags
846 CONFIG_CMD_EXPORTENV * export the environment
847 CONFIG_CMD_EXT2 * ext2 command support
848 CONFIG_CMD_EXT4 * ext4 command support
849 CONFIG_CMD_SAVEENV saveenv
850 CONFIG_CMD_FDC * Floppy Disk Support
851 CONFIG_CMD_FAT * FAT command support
852 CONFIG_CMD_FDOS * Dos diskette Support
853 CONFIG_CMD_FLASH flinfo, erase, protect
854 CONFIG_CMD_FPGA FPGA device initialization support
855 CONFIG_CMD_GETTIME * Get time since boot
856 CONFIG_CMD_GO * the 'go' command (exec code)
857 CONFIG_CMD_GREPENV * search environment
858 CONFIG_CMD_HASH * calculate hash / digest
859 CONFIG_CMD_HWFLOW * RTS/CTS hw flow control
860 CONFIG_CMD_I2C * I2C serial bus support
861 CONFIG_CMD_IDE * IDE harddisk support
862 CONFIG_CMD_IMI iminfo
863 CONFIG_CMD_IMLS List all images found in NOR flash
864 CONFIG_CMD_IMLS_NAND List all images found in NAND flash
865 CONFIG_CMD_IMMAP * IMMR dump support
866 CONFIG_CMD_IMPORTENV * import an environment
867 CONFIG_CMD_INI * import data from an ini file into the env
868 CONFIG_CMD_IRQ * irqinfo
869 CONFIG_CMD_ITEST Integer/string test of 2 values
870 CONFIG_CMD_JFFS2 * JFFS2 Support
871 CONFIG_CMD_KGDB * kgdb
872 CONFIG_CMD_LDRINFO ldrinfo (display Blackfin loader)
873 CONFIG_CMD_LINK_LOCAL * link-local IP address auto-configuration
875 CONFIG_CMD_LOADB loadb
876 CONFIG_CMD_LOADS loads
877 CONFIG_CMD_MD5SUM print md5 message digest
878 (requires CONFIG_CMD_MEMORY and CONFIG_MD5)
879 CONFIG_CMD_MEMINFO * Display detailed memory information
880 CONFIG_CMD_MEMORY md, mm, nm, mw, cp, cmp, crc, base,
882 CONFIG_CMD_MEMTEST mtest
883 CONFIG_CMD_MISC Misc functions like sleep etc
884 CONFIG_CMD_MMC * MMC memory mapped support
885 CONFIG_CMD_MII * MII utility commands
886 CONFIG_CMD_MTDPARTS * MTD partition support
887 CONFIG_CMD_NAND * NAND support
888 CONFIG_CMD_NET bootp, tftpboot, rarpboot
889 CONFIG_CMD_PCA953X * PCA953x I2C gpio commands
890 CONFIG_CMD_PCA953X_INFO * PCA953x I2C gpio info command
891 CONFIG_CMD_PCI * pciinfo
892 CONFIG_CMD_PCMCIA * PCMCIA support
893 CONFIG_CMD_PING * send ICMP ECHO_REQUEST to network
895 CONFIG_CMD_PORTIO * Port I/O
896 CONFIG_CMD_READ * Read raw data from partition
897 CONFIG_CMD_REGINFO * Register dump
898 CONFIG_CMD_RUN run command in env variable
899 CONFIG_CMD_SANDBOX * sb command to access sandbox features
900 CONFIG_CMD_SAVES * save S record dump
901 CONFIG_CMD_SCSI * SCSI Support
902 CONFIG_CMD_SDRAM * print SDRAM configuration information
903 (requires CONFIG_CMD_I2C)
904 CONFIG_CMD_SETGETDCR Support for DCR Register access
906 CONFIG_CMD_SF * Read/write/erase SPI NOR flash
907 CONFIG_CMD_SHA1SUM print sha1 memory digest
908 (requires CONFIG_CMD_MEMORY)
909 CONFIG_CMD_SOURCE "source" command Support
910 CONFIG_CMD_SPI * SPI serial bus support
911 CONFIG_CMD_TFTPSRV * TFTP transfer in server mode
912 CONFIG_CMD_TFTPPUT * TFTP put command (upload)
913 CONFIG_CMD_TIME * run command and report execution time (ARM specific)
914 CONFIG_CMD_TIMER * access to the system tick timer
915 CONFIG_CMD_USB * USB support
916 CONFIG_CMD_CDP * Cisco Discover Protocol support
917 CONFIG_CMD_MFSL * Microblaze FSL support
920 EXAMPLE: If you want all functions except of network
921 support you can write:
923 #include "config_cmd_all.h"
924 #undef CONFIG_CMD_NET
927 fdt (flattened device tree) command: CONFIG_OF_LIBFDT
929 Note: Don't enable the "icache" and "dcache" commands
930 (configuration option CONFIG_CMD_CACHE) unless you know
931 what you (and your U-Boot users) are doing. Data
932 cache cannot be enabled on systems like the 8xx or
933 8260 (where accesses to the IMMR region must be
934 uncached), and it cannot be disabled on all other
935 systems where we (mis-) use the data cache to hold an
936 initial stack and some data.
939 XXX - this list needs to get updated!
943 If this variable is defined, U-Boot will use a device tree
944 to configure its devices, instead of relying on statically
945 compiled #defines in the board file. This option is
946 experimental and only available on a few boards. The device
947 tree is available in the global data as gd->fdt_blob.
949 U-Boot needs to get its device tree from somewhere. This can
950 be done using one of the two options below:
953 If this variable is defined, U-Boot will embed a device tree
954 binary in its image. This device tree file should be in the
955 board directory and called <soc>-<board>.dts. The binary file
956 is then picked up in board_init_f() and made available through
957 the global data structure as gd->blob.
960 If this variable is defined, U-Boot will build a device tree
961 binary. It will be called u-boot.dtb. Architecture-specific
962 code will locate it at run-time. Generally this works by:
964 cat u-boot.bin u-boot.dtb >image.bin
966 and in fact, U-Boot does this for you, creating a file called
967 u-boot-dtb.bin which is useful in the common case. You can
968 still use the individual files if you need something more
973 If this variable is defined, it enables watchdog
974 support for the SoC. There must be support in the SoC
975 specific code for a watchdog. For the 8xx and 8260
976 CPUs, the SIU Watchdog feature is enabled in the SYPCR
977 register. When supported for a specific SoC is
978 available, then no further board specific code should
982 When using a watchdog circuitry external to the used
983 SoC, then define this variable and provide board
984 specific code for the "hw_watchdog_reset" function.
987 CONFIG_VERSION_VARIABLE
988 If this variable is defined, an environment variable
989 named "ver" is created by U-Boot showing the U-Boot
990 version as printed by the "version" command.
991 Any change to this variable will be reverted at the
996 When CONFIG_CMD_DATE is selected, the type of the RTC
997 has to be selected, too. Define exactly one of the
1000 CONFIG_RTC_MPC8xx - use internal RTC of MPC8xx
1001 CONFIG_RTC_PCF8563 - use Philips PCF8563 RTC
1002 CONFIG_RTC_MC13XXX - use MC13783 or MC13892 RTC
1003 CONFIG_RTC_MC146818 - use MC146818 RTC
1004 CONFIG_RTC_DS1307 - use Maxim, Inc. DS1307 RTC
1005 CONFIG_RTC_DS1337 - use Maxim, Inc. DS1337 RTC
1006 CONFIG_RTC_DS1338 - use Maxim, Inc. DS1338 RTC
1007 CONFIG_RTC_DS164x - use Dallas DS164x RTC
1008 CONFIG_RTC_ISL1208 - use Intersil ISL1208 RTC
1009 CONFIG_RTC_MAX6900 - use Maxim, Inc. MAX6900 RTC
1010 CONFIG_SYS_RTC_DS1337_NOOSC - Turn off the OSC output for DS1337
1011 CONFIG_SYS_RV3029_TCR - enable trickle charger on
1014 Note that if the RTC uses I2C, then the I2C interface
1015 must also be configured. See I2C Support, below.
1018 CONFIG_PCA953X - use NXP's PCA953X series I2C GPIO
1019 CONFIG_PCA953X_INFO - enable pca953x info command
1021 The CONFIG_SYS_I2C_PCA953X_WIDTH option specifies a list of
1022 chip-ngpio pairs that tell the PCA953X driver the number of
1023 pins supported by a particular chip.
1025 Note that if the GPIO device uses I2C, then the I2C interface
1026 must also be configured. See I2C Support, below.
1028 - Timestamp Support:
1030 When CONFIG_TIMESTAMP is selected, the timestamp
1031 (date and time) of an image is printed by image
1032 commands like bootm or iminfo. This option is
1033 automatically enabled when you select CONFIG_CMD_DATE .
1035 - Partition Labels (disklabels) Supported:
1036 Zero or more of the following:
1037 CONFIG_MAC_PARTITION Apple's MacOS partition table.
1038 CONFIG_DOS_PARTITION MS Dos partition table, traditional on the
1039 Intel architecture, USB sticks, etc.
1040 CONFIG_ISO_PARTITION ISO partition table, used on CDROM etc.
1041 CONFIG_EFI_PARTITION GPT partition table, common when EFI is the
1042 bootloader. Note 2TB partition limit; see
1044 CONFIG_MTD_PARTITIONS Memory Technology Device partition table.
1046 If IDE or SCSI support is enabled (CONFIG_CMD_IDE or
1047 CONFIG_CMD_SCSI) you must configure support for at
1048 least one non-MTD partition type as well.
1051 CONFIG_IDE_RESET_ROUTINE - this is defined in several
1052 board configurations files but used nowhere!
1054 CONFIG_IDE_RESET - is this is defined, IDE Reset will
1055 be performed by calling the function
1056 ide_set_reset(int reset)
1057 which has to be defined in a board specific file
1062 Set this to enable ATAPI support.
1067 Set this to enable support for disks larger than 137GB
1068 Also look at CONFIG_SYS_64BIT_LBA.
1069 Whithout these , LBA48 support uses 32bit variables and will 'only'
1070 support disks up to 2.1TB.
1072 CONFIG_SYS_64BIT_LBA:
1073 When enabled, makes the IDE subsystem use 64bit sector addresses.
1077 At the moment only there is only support for the
1078 SYM53C8XX SCSI controller; define
1079 CONFIG_SCSI_SYM53C8XX to enable it.
1081 CONFIG_SYS_SCSI_MAX_LUN [8], CONFIG_SYS_SCSI_MAX_SCSI_ID [7] and
1082 CONFIG_SYS_SCSI_MAX_DEVICE [CONFIG_SYS_SCSI_MAX_SCSI_ID *
1083 CONFIG_SYS_SCSI_MAX_LUN] can be adjusted to define the
1084 maximum numbers of LUNs, SCSI ID's and target
1086 CONFIG_SYS_SCSI_SYM53C8XX_CCF to fix clock timing (80Mhz)
1088 The environment variable 'scsidevs' is set to the number of
1089 SCSI devices found during the last scan.
1091 - NETWORK Support (PCI):
1093 Support for Intel 8254x/8257x gigabit chips.
1096 Utility code for direct access to the SPI bus on Intel 8257x.
1097 This does not do anything useful unless you set at least one
1098 of CONFIG_CMD_E1000 or CONFIG_E1000_SPI_GENERIC.
1100 CONFIG_E1000_SPI_GENERIC
1101 Allow generic access to the SPI bus on the Intel 8257x, for
1102 example with the "sspi" command.
1105 Management command for E1000 devices. When used on devices
1106 with SPI support you can reprogram the EEPROM from U-Boot.
1108 CONFIG_E1000_FALLBACK_MAC
1109 default MAC for empty EEPROM after production.
1112 Support for Intel 82557/82559/82559ER chips.
1113 Optional CONFIG_EEPRO100_SROM_WRITE enables EEPROM
1114 write routine for first time initialisation.
1117 Support for Digital 2114x chips.
1118 Optional CONFIG_TULIP_SELECT_MEDIA for board specific
1119 modem chip initialisation (KS8761/QS6611).
1122 Support for National dp83815 chips.
1125 Support for National dp8382[01] gigabit chips.
1127 - NETWORK Support (other):
1129 CONFIG_DRIVER_AT91EMAC
1130 Support for AT91RM9200 EMAC.
1133 Define this to use reduced MII inteface
1135 CONFIG_DRIVER_AT91EMAC_QUIET
1136 If this defined, the driver is quiet.
1137 The driver doen't show link status messages.
1139 CONFIG_CALXEDA_XGMAC
1140 Support for the Calxeda XGMAC device
1143 Support for SMSC's LAN91C96 chips.
1145 CONFIG_LAN91C96_BASE
1146 Define this to hold the physical address
1147 of the LAN91C96's I/O space
1149 CONFIG_LAN91C96_USE_32_BIT
1150 Define this to enable 32 bit addressing
1153 Support for SMSC's LAN91C111 chip
1155 CONFIG_SMC91111_BASE
1156 Define this to hold the physical address
1157 of the device (I/O space)
1159 CONFIG_SMC_USE_32_BIT
1160 Define this if data bus is 32 bits
1162 CONFIG_SMC_USE_IOFUNCS
1163 Define this to use i/o functions instead of macros
1164 (some hardware wont work with macros)
1166 CONFIG_DRIVER_TI_EMAC
1167 Support for davinci emac
1169 CONFIG_SYS_DAVINCI_EMAC_PHY_COUNT
1170 Define this if you have more then 3 PHYs.
1173 Support for Faraday's FTGMAC100 Gigabit SoC Ethernet
1175 CONFIG_FTGMAC100_EGIGA
1176 Define this to use GE link update with gigabit PHY.
1177 Define this if FTGMAC100 is connected to gigabit PHY.
1178 If your system has 10/100 PHY only, it might not occur
1179 wrong behavior. Because PHY usually return timeout or
1180 useless data when polling gigabit status and gigabit
1181 control registers. This behavior won't affect the
1182 correctnessof 10/100 link speed update.
1185 Support for SMSC's LAN911x and LAN921x chips
1188 Define this to hold the physical address
1189 of the device (I/O space)
1191 CONFIG_SMC911X_32_BIT
1192 Define this if data bus is 32 bits
1194 CONFIG_SMC911X_16_BIT
1195 Define this if data bus is 16 bits. If your processor
1196 automatically converts one 32 bit word to two 16 bit
1197 words you may also try CONFIG_SMC911X_32_BIT.
1200 Support for Renesas on-chip Ethernet controller
1202 CONFIG_SH_ETHER_USE_PORT
1203 Define the number of ports to be used
1205 CONFIG_SH_ETHER_PHY_ADDR
1206 Define the ETH PHY's address
1208 CONFIG_SH_ETHER_CACHE_WRITEBACK
1209 If this option is set, the driver enables cache flush.
1212 CONFIG_GENERIC_LPC_TPM
1213 Support for generic parallel port TPM devices. Only one device
1214 per system is supported at this time.
1216 CONFIG_TPM_TIS_BASE_ADDRESS
1217 Base address where the generic TPM device is mapped
1218 to. Contemporary x86 systems usually map it at
1222 At the moment only the UHCI host controller is
1223 supported (PIP405, MIP405, MPC5200); define
1224 CONFIG_USB_UHCI to enable it.
1225 define CONFIG_USB_KEYBOARD to enable the USB Keyboard
1226 and define CONFIG_USB_STORAGE to enable the USB
1229 Supported are USB Keyboards and USB Floppy drives
1231 MPC5200 USB requires additional defines:
1233 for 528 MHz Clock: 0x0001bbbb
1237 for differential drivers: 0x00001000
1238 for single ended drivers: 0x00005000
1239 for differential drivers on PSC3: 0x00000100
1240 for single ended drivers on PSC3: 0x00004100
1241 CONFIG_SYS_USB_EVENT_POLL
1242 May be defined to allow interrupt polling
1243 instead of using asynchronous interrupts
1245 CONFIG_USB_EHCI_TXFIFO_THRESH enables setting of the
1246 txfilltuning field in the EHCI controller on reset.
1249 Define the below if you wish to use the USB console.
1250 Once firmware is rebuilt from a serial console issue the
1251 command "setenv stdin usbtty; setenv stdout usbtty" and
1252 attach your USB cable. The Unix command "dmesg" should print
1253 it has found a new device. The environment variable usbtty
1254 can be set to gserial or cdc_acm to enable your device to
1255 appear to a USB host as a Linux gserial device or a
1256 Common Device Class Abstract Control Model serial device.
1257 If you select usbtty = gserial you should be able to enumerate
1259 # modprobe usbserial vendor=0xVendorID product=0xProductID
1260 else if using cdc_acm, simply setting the environment
1261 variable usbtty to be cdc_acm should suffice. The following
1262 might be defined in YourBoardName.h
1265 Define this to build a UDC device
1268 Define this to have a tty type of device available to
1269 talk to the UDC device
1272 Define this to enable the high speed support for usb
1273 device and usbtty. If this feature is enabled, a routine
1274 int is_usbd_high_speed(void)
1275 also needs to be defined by the driver to dynamically poll
1276 whether the enumeration has succeded at high speed or full
1279 CONFIG_SYS_CONSOLE_IS_IN_ENV
1280 Define this if you want stdin, stdout &/or stderr to
1284 CONFIG_SYS_USB_EXTC_CLK 0xBLAH
1285 Derive USB clock from external clock "blah"
1286 - CONFIG_SYS_USB_EXTC_CLK 0x02
1288 CONFIG_SYS_USB_BRG_CLK 0xBLAH
1289 Derive USB clock from brgclk
1290 - CONFIG_SYS_USB_BRG_CLK 0x04
1292 If you have a USB-IF assigned VendorID then you may wish to
1293 define your own vendor specific values either in BoardName.h
1294 or directly in usbd_vendor_info.h. If you don't define
1295 CONFIG_USBD_MANUFACTURER, CONFIG_USBD_PRODUCT_NAME,
1296 CONFIG_USBD_VENDORID and CONFIG_USBD_PRODUCTID, then U-Boot
1297 should pretend to be a Linux device to it's target host.
1299 CONFIG_USBD_MANUFACTURER
1300 Define this string as the name of your company for
1301 - CONFIG_USBD_MANUFACTURER "my company"
1303 CONFIG_USBD_PRODUCT_NAME
1304 Define this string as the name of your product
1305 - CONFIG_USBD_PRODUCT_NAME "acme usb device"
1307 CONFIG_USBD_VENDORID
1308 Define this as your assigned Vendor ID from the USB
1309 Implementors Forum. This *must* be a genuine Vendor ID
1310 to avoid polluting the USB namespace.
1311 - CONFIG_USBD_VENDORID 0xFFFF
1313 CONFIG_USBD_PRODUCTID
1314 Define this as the unique Product ID
1316 - CONFIG_USBD_PRODUCTID 0xFFFF
1318 - ULPI Layer Support:
1319 The ULPI (UTMI Low Pin (count) Interface) PHYs are supported via
1320 the generic ULPI layer. The generic layer accesses the ULPI PHY
1321 via the platform viewport, so you need both the genric layer and
1322 the viewport enabled. Currently only Chipidea/ARC based
1323 viewport is supported.
1324 To enable the ULPI layer support, define CONFIG_USB_ULPI and
1325 CONFIG_USB_ULPI_VIEWPORT in your board configuration file.
1326 If your ULPI phy needs a different reference clock than the
1327 standard 24 MHz then you have to define CONFIG_ULPI_REF_CLK to
1328 the appropriate value in Hz.
1331 The MMC controller on the Intel PXA is supported. To
1332 enable this define CONFIG_MMC. The MMC can be
1333 accessed from the boot prompt by mapping the device
1334 to physical memory similar to flash. Command line is
1335 enabled with CONFIG_CMD_MMC. The MMC driver also works with
1336 the FAT fs. This is enabled with CONFIG_CMD_FAT.
1339 Support for Renesas on-chip MMCIF controller
1341 CONFIG_SH_MMCIF_ADDR
1342 Define the base address of MMCIF registers
1345 Define the clock frequency for MMCIF
1347 - USB Device Firmware Update (DFU) class support:
1349 This enables the USB portion of the DFU USB class
1352 This enables the command "dfu" which is used to have
1353 U-Boot create a DFU class device via USB. This command
1354 requires that the "dfu_alt_info" environment variable be
1355 set and define the alt settings to expose to the host.
1358 This enables support for exposing (e)MMC devices via DFU.
1361 This enables support for exposing NAND devices via DFU.
1363 CONFIG_SYS_DFU_MAX_FILE_SIZE
1364 When updating files rather than the raw storage device,
1365 we use a static buffer to copy the file into and then write
1366 the buffer once we've been given the whole file. Define
1367 this to the maximum filesize (in bytes) for the buffer.
1368 Default is 4 MiB if undefined.
1370 - Journaling Flash filesystem support:
1371 CONFIG_JFFS2_NAND, CONFIG_JFFS2_NAND_OFF, CONFIG_JFFS2_NAND_SIZE,
1372 CONFIG_JFFS2_NAND_DEV
1373 Define these for a default partition on a NAND device
1375 CONFIG_SYS_JFFS2_FIRST_SECTOR,
1376 CONFIG_SYS_JFFS2_FIRST_BANK, CONFIG_SYS_JFFS2_NUM_BANKS
1377 Define these for a default partition on a NOR device
1379 CONFIG_SYS_JFFS_CUSTOM_PART
1380 Define this to create an own partition. You have to provide a
1381 function struct part_info* jffs2_part_info(int part_num)
1383 If you define only one JFFS2 partition you may also want to
1384 #define CONFIG_SYS_JFFS_SINGLE_PART 1
1385 to disable the command chpart. This is the default when you
1386 have not defined a custom partition
1388 - FAT(File Allocation Table) filesystem write function support:
1391 Define this to enable support for saving memory data as a
1392 file in FAT formatted partition.
1394 This will also enable the command "fatwrite" enabling the
1395 user to write files to FAT.
1397 CBFS (Coreboot Filesystem) support
1400 Define this to enable support for reading from a Coreboot
1401 filesystem. Available commands are cbfsinit, cbfsinfo, cbfsls
1407 Define this to enable standard (PC-Style) keyboard
1411 Standard PC keyboard driver with US (is default) and
1412 GERMAN key layout (switch via environment 'keymap=de') support.
1413 Export function i8042_kbd_init, i8042_tstc and i8042_getc
1414 for cfb_console. Supports cursor blinking.
1419 Define this to enable video support (for output to
1422 CONFIG_VIDEO_CT69000
1424 Enable Chips & Technologies 69000 Video chip
1426 CONFIG_VIDEO_SMI_LYNXEM
1427 Enable Silicon Motion SMI 712/710/810 Video chip. The
1428 video output is selected via environment 'videoout'
1429 (1 = LCD and 2 = CRT). If videoout is undefined, CRT is
1432 For the CT69000 and SMI_LYNXEM drivers, videomode is
1433 selected via environment 'videomode'. Two different ways
1435 - "videomode=num" 'num' is a standard LiLo mode numbers.
1436 Following standard modes are supported (* is default):
1438 Colors 640x480 800x600 1024x768 1152x864 1280x1024
1439 -------------+---------------------------------------------
1440 8 bits | 0x301* 0x303 0x305 0x161 0x307
1441 15 bits | 0x310 0x313 0x316 0x162 0x319
1442 16 bits | 0x311 0x314 0x317 0x163 0x31A
1443 24 bits | 0x312 0x315 0x318 ? 0x31B
1444 -------------+---------------------------------------------
1445 (i.e. setenv videomode 317; saveenv; reset;)
1447 - "videomode=bootargs" all the video parameters are parsed
1448 from the bootargs. (See drivers/video/videomodes.c)
1451 CONFIG_VIDEO_SED13806
1452 Enable Epson SED13806 driver. This driver supports 8bpp
1453 and 16bpp modes defined by CONFIG_VIDEO_SED13806_8BPP
1454 or CONFIG_VIDEO_SED13806_16BPP
1457 Enable the Freescale DIU video driver. Reference boards for
1458 SOCs that have a DIU should define this macro to enable DIU
1459 support, and should also define these other macros:
1465 CONFIG_VIDEO_SW_CURSOR
1466 CONFIG_VGA_AS_SINGLE_DEVICE
1468 CONFIG_VIDEO_BMP_LOGO
1470 The DIU driver will look for the 'video-mode' environment
1471 variable, and if defined, enable the DIU as a console during
1472 boot. See the documentation file README.video for a
1473 description of this variable.
1477 Enable the VGA video / BIOS for x86. The alternative if you
1478 are using coreboot is to use the coreboot frame buffer
1485 Define this to enable a custom keyboard support.
1486 This simply calls drv_keyboard_init() which must be
1487 defined in your board-specific files.
1488 The only board using this so far is RBC823.
1490 - LCD Support: CONFIG_LCD
1492 Define this to enable LCD support (for output to LCD
1493 display); also select one of the supported displays
1494 by defining one of these:
1498 HITACHI TX09D70VM1CCA, 3.5", 240x320.
1500 CONFIG_NEC_NL6448AC33:
1502 NEC NL6448AC33-18. Active, color, single scan.
1504 CONFIG_NEC_NL6448BC20
1506 NEC NL6448BC20-08. 6.5", 640x480.
1507 Active, color, single scan.
1509 CONFIG_NEC_NL6448BC33_54
1511 NEC NL6448BC33-54. 10.4", 640x480.
1512 Active, color, single scan.
1516 Sharp 320x240. Active, color, single scan.
1517 It isn't 16x9, and I am not sure what it is.
1519 CONFIG_SHARP_LQ64D341
1521 Sharp LQ64D341 display, 640x480.
1522 Active, color, single scan.
1526 HLD1045 display, 640x480.
1527 Active, color, single scan.
1531 Optrex CBL50840-2 NF-FW 99 22 M5
1533 Hitachi LMG6912RPFC-00T
1537 320x240. Black & white.
1539 Normally display is black on white background; define
1540 CONFIG_SYS_WHITE_ON_BLACK to get it inverted.
1542 CONFIG_LCD_ALIGNMENT
1544 Normally the LCD is page-aligned (tyically 4KB). If this is
1545 defined then the LCD will be aligned to this value instead.
1546 For ARM it is sometimes useful to use MMU_SECTION_SIZE
1547 here, since it is cheaper to change data cache settings on
1548 a per-section basis.
1550 CONFIG_CONSOLE_SCROLL_LINES
1552 When the console need to be scrolled, this is the number of
1553 lines to scroll by. It defaults to 1. Increasing this makes
1554 the console jump but can help speed up operation when scrolling
1559 Support drawing of RLE8-compressed bitmaps on the LCD.
1563 Enables an 'i2c edid' command which can read EDID
1564 information over I2C from an attached LCD display.
1566 - Splash Screen Support: CONFIG_SPLASH_SCREEN
1568 If this option is set, the environment is checked for
1569 a variable "splashimage". If found, the usual display
1570 of logo, copyright and system information on the LCD
1571 is suppressed and the BMP image at the address
1572 specified in "splashimage" is loaded instead. The
1573 console is redirected to the "nulldev", too. This
1574 allows for a "silent" boot where a splash screen is
1575 loaded very quickly after power-on.
1577 CONFIG_SPLASHIMAGE_GUARD
1579 If this option is set, then U-Boot will prevent the environment
1580 variable "splashimage" from being set to a problematic address
1581 (see README.displaying-bmps and README.arm-unaligned-accesses).
1582 This option is useful for targets where, due to alignment
1583 restrictions, an improperly aligned BMP image will cause a data
1584 abort. If you think you will not have problems with unaligned
1585 accesses (for example because your toolchain prevents them)
1586 there is no need to set this option.
1588 CONFIG_SPLASH_SCREEN_ALIGN
1590 If this option is set the splash image can be freely positioned
1591 on the screen. Environment variable "splashpos" specifies the
1592 position as "x,y". If a positive number is given it is used as
1593 number of pixel from left/top. If a negative number is given it
1594 is used as number of pixel from right/bottom. You can also
1595 specify 'm' for centering the image.
1598 setenv splashpos m,m
1599 => image at center of screen
1601 setenv splashpos 30,20
1602 => image at x = 30 and y = 20
1604 setenv splashpos -10,m
1605 => vertically centered image
1606 at x = dspWidth - bmpWidth - 9
1608 CONFIG_SPLASH_SCREEN_PREPARE
1610 If this option is set then the board_splash_screen_prepare()
1611 function, which must be defined in your code, is called as part
1612 of the splash screen display sequence. It gives the board an
1613 opportunity to prepare the splash image data before it is
1614 processed and sent to the frame buffer by U-Boot.
1616 - Gzip compressed BMP image support: CONFIG_VIDEO_BMP_GZIP
1618 If this option is set, additionally to standard BMP
1619 images, gzipped BMP images can be displayed via the
1620 splashscreen support or the bmp command.
1622 - Run length encoded BMP image (RLE8) support: CONFIG_VIDEO_BMP_RLE8
1624 If this option is set, 8-bit RLE compressed BMP images
1625 can be displayed via the splashscreen support or the
1628 - Do compresssing for memory range:
1631 If this option is set, it would use zlib deflate method
1632 to compress the specified memory at its best effort.
1634 - Compression support:
1637 If this option is set, support for bzip2 compressed
1638 images is included. If not, only uncompressed and gzip
1639 compressed images are supported.
1641 NOTE: the bzip2 algorithm requires a lot of RAM, so
1642 the malloc area (as defined by CONFIG_SYS_MALLOC_LEN) should
1647 If this option is set, support for lzma compressed
1650 Note: The LZMA algorithm adds between 2 and 4KB of code and it
1651 requires an amount of dynamic memory that is given by the
1654 (1846 + 768 << (lc + lp)) * sizeof(uint16)
1656 Where lc and lp stand for, respectively, Literal context bits
1657 and Literal pos bits.
1659 This value is upper-bounded by 14MB in the worst case. Anyway,
1660 for a ~4MB large kernel image, we have lc=3 and lp=0 for a
1661 total amount of (1846 + 768 << (3 + 0)) * 2 = ~41KB... that is
1662 a very small buffer.
1664 Use the lzmainfo tool to determinate the lc and lp values and
1665 then calculate the amount of needed dynamic memory (ensuring
1666 the appropriate CONFIG_SYS_MALLOC_LEN value).
1671 The address of PHY on MII bus.
1673 CONFIG_PHY_CLOCK_FREQ (ppc4xx)
1675 The clock frequency of the MII bus
1679 If this option is set, support for speed/duplex
1680 detection of gigabit PHY is included.
1682 CONFIG_PHY_RESET_DELAY
1684 Some PHY like Intel LXT971A need extra delay after
1685 reset before any MII register access is possible.
1686 For such PHY, set this option to the usec delay
1687 required. (minimum 300usec for LXT971A)
1689 CONFIG_PHY_CMD_DELAY (ppc4xx)
1691 Some PHY like Intel LXT971A need extra delay after
1692 command issued before MII status register can be read
1702 Define a default value for Ethernet address to use
1703 for the respective Ethernet interface, in case this
1704 is not determined automatically.
1709 Define a default value for the IP address to use for
1710 the default Ethernet interface, in case this is not
1711 determined through e.g. bootp.
1712 (Environment variable "ipaddr")
1714 - Server IP address:
1717 Defines a default value for the IP address of a TFTP
1718 server to contact when using the "tftboot" command.
1719 (Environment variable "serverip")
1721 CONFIG_KEEP_SERVERADDR
1723 Keeps the server's MAC address, in the env 'serveraddr'
1724 for passing to bootargs (like Linux's netconsole option)
1726 - Gateway IP address:
1729 Defines a default value for the IP address of the
1730 default router where packets to other networks are
1732 (Environment variable "gatewayip")
1737 Defines a default value for the subnet mask (or
1738 routing prefix) which is used to determine if an IP
1739 address belongs to the local subnet or needs to be
1740 forwarded through a router.
1741 (Environment variable "netmask")
1743 - Multicast TFTP Mode:
1746 Defines whether you want to support multicast TFTP as per
1747 rfc-2090; for example to work with atftp. Lets lots of targets
1748 tftp down the same boot image concurrently. Note: the Ethernet
1749 driver in use must provide a function: mcast() to join/leave a
1752 - BOOTP Recovery Mode:
1753 CONFIG_BOOTP_RANDOM_DELAY
1755 If you have many targets in a network that try to
1756 boot using BOOTP, you may want to avoid that all
1757 systems send out BOOTP requests at precisely the same
1758 moment (which would happen for instance at recovery
1759 from a power failure, when all systems will try to
1760 boot, thus flooding the BOOTP server. Defining
1761 CONFIG_BOOTP_RANDOM_DELAY causes a random delay to be
1762 inserted before sending out BOOTP requests. The
1763 following delays are inserted then:
1765 1st BOOTP request: delay 0 ... 1 sec
1766 2nd BOOTP request: delay 0 ... 2 sec
1767 3rd BOOTP request: delay 0 ... 4 sec
1769 BOOTP requests: delay 0 ... 8 sec
1771 - DHCP Advanced Options:
1772 You can fine tune the DHCP functionality by defining
1773 CONFIG_BOOTP_* symbols:
1775 CONFIG_BOOTP_SUBNETMASK
1776 CONFIG_BOOTP_GATEWAY
1777 CONFIG_BOOTP_HOSTNAME
1778 CONFIG_BOOTP_NISDOMAIN
1779 CONFIG_BOOTP_BOOTPATH
1780 CONFIG_BOOTP_BOOTFILESIZE
1783 CONFIG_BOOTP_SEND_HOSTNAME
1784 CONFIG_BOOTP_NTPSERVER
1785 CONFIG_BOOTP_TIMEOFFSET
1786 CONFIG_BOOTP_VENDOREX
1787 CONFIG_BOOTP_MAY_FAIL
1789 CONFIG_BOOTP_SERVERIP - TFTP server will be the serverip
1790 environment variable, not the BOOTP server.
1792 CONFIG_BOOTP_MAY_FAIL - If the DHCP server is not found
1793 after the configured retry count, the call will fail
1794 instead of starting over. This can be used to fail over
1795 to Link-local IP address configuration if the DHCP server
1798 CONFIG_BOOTP_DNS2 - If a DHCP client requests the DNS
1799 serverip from a DHCP server, it is possible that more
1800 than one DNS serverip is offered to the client.
1801 If CONFIG_BOOTP_DNS2 is enabled, the secondary DNS
1802 serverip will be stored in the additional environment
1803 variable "dnsip2". The first DNS serverip is always
1804 stored in the variable "dnsip", when CONFIG_BOOTP_DNS
1807 CONFIG_BOOTP_SEND_HOSTNAME - Some DHCP servers are capable
1808 to do a dynamic update of a DNS server. To do this, they
1809 need the hostname of the DHCP requester.
1810 If CONFIG_BOOTP_SEND_HOSTNAME is defined, the content
1811 of the "hostname" environment variable is passed as
1812 option 12 to the DHCP server.
1814 CONFIG_BOOTP_DHCP_REQUEST_DELAY
1816 A 32bit value in microseconds for a delay between
1817 receiving a "DHCP Offer" and sending the "DHCP Request".
1818 This fixes a problem with certain DHCP servers that don't
1819 respond 100% of the time to a "DHCP request". E.g. On an
1820 AT91RM9200 processor running at 180MHz, this delay needed
1821 to be *at least* 15,000 usec before a Windows Server 2003
1822 DHCP server would reply 100% of the time. I recommend at
1823 least 50,000 usec to be safe. The alternative is to hope
1824 that one of the retries will be successful but note that
1825 the DHCP timeout and retry process takes a longer than
1828 - Link-local IP address negotiation:
1829 Negotiate with other link-local clients on the local network
1830 for an address that doesn't require explicit configuration.
1831 This is especially useful if a DHCP server cannot be guaranteed
1832 to exist in all environments that the device must operate.
1834 See doc/README.link-local for more information.
1837 CONFIG_CDP_DEVICE_ID
1839 The device id used in CDP trigger frames.
1841 CONFIG_CDP_DEVICE_ID_PREFIX
1843 A two character string which is prefixed to the MAC address
1848 A printf format string which contains the ascii name of
1849 the port. Normally is set to "eth%d" which sets
1850 eth0 for the first Ethernet, eth1 for the second etc.
1852 CONFIG_CDP_CAPABILITIES
1854 A 32bit integer which indicates the device capabilities;
1855 0x00000010 for a normal host which does not forwards.
1859 An ascii string containing the version of the software.
1863 An ascii string containing the name of the platform.
1867 A 32bit integer sent on the trigger.
1869 CONFIG_CDP_POWER_CONSUMPTION
1871 A 16bit integer containing the power consumption of the
1872 device in .1 of milliwatts.
1874 CONFIG_CDP_APPLIANCE_VLAN_TYPE
1876 A byte containing the id of the VLAN.
1878 - Status LED: CONFIG_STATUS_LED
1880 Several configurations allow to display the current
1881 status using a LED. For instance, the LED will blink
1882 fast while running U-Boot code, stop blinking as
1883 soon as a reply to a BOOTP request was received, and
1884 start blinking slow once the Linux kernel is running
1885 (supported by a status LED driver in the Linux
1886 kernel). Defining CONFIG_STATUS_LED enables this
1889 - CAN Support: CONFIG_CAN_DRIVER
1891 Defining CONFIG_CAN_DRIVER enables CAN driver support
1892 on those systems that support this (optional)
1893 feature, like the TQM8xxL modules.
1895 - I2C Support: CONFIG_HARD_I2C | CONFIG_SOFT_I2C
1897 These enable I2C serial bus commands. Defining either of
1898 (but not both of) CONFIG_HARD_I2C or CONFIG_SOFT_I2C will
1899 include the appropriate I2C driver for the selected CPU.
1901 This will allow you to use i2c commands at the u-boot
1902 command line (as long as you set CONFIG_CMD_I2C in
1903 CONFIG_COMMANDS) and communicate with i2c based realtime
1904 clock chips. See common/cmd_i2c.c for a description of the
1905 command line interface.
1907 CONFIG_HARD_I2C selects a hardware I2C controller.
1909 CONFIG_SOFT_I2C configures u-boot to use a software (aka
1910 bit-banging) driver instead of CPM or similar hardware
1913 There are several other quantities that must also be
1914 defined when you define CONFIG_HARD_I2C or CONFIG_SOFT_I2C.
1916 In both cases you will need to define CONFIG_SYS_I2C_SPEED
1917 to be the frequency (in Hz) at which you wish your i2c bus
1918 to run and CONFIG_SYS_I2C_SLAVE to be the address of this node (ie
1919 the CPU's i2c node address).
1921 Now, the u-boot i2c code for the mpc8xx
1922 (arch/powerpc/cpu/mpc8xx/i2c.c) sets the CPU up as a master node
1923 and so its address should therefore be cleared to 0 (See,
1924 eg, MPC823e User's Manual p.16-473). So, set
1925 CONFIG_SYS_I2C_SLAVE to 0.
1927 CONFIG_SYS_I2C_INIT_MPC5XXX
1929 When a board is reset during an i2c bus transfer
1930 chips might think that the current transfer is still
1931 in progress. Reset the slave devices by sending start
1932 commands until the slave device responds.
1934 That's all that's required for CONFIG_HARD_I2C.
1936 If you use the software i2c interface (CONFIG_SOFT_I2C)
1937 then the following macros need to be defined (examples are
1938 from include/configs/lwmon.h):
1942 (Optional). Any commands necessary to enable the I2C
1943 controller or configure ports.
1945 eg: #define I2C_INIT (immr->im_cpm.cp_pbdir |= PB_SCL)
1949 (Only for MPC8260 CPU). The I/O port to use (the code
1950 assumes both bits are on the same port). Valid values
1951 are 0..3 for ports A..D.
1955 The code necessary to make the I2C data line active
1956 (driven). If the data line is open collector, this
1959 eg: #define I2C_ACTIVE (immr->im_cpm.cp_pbdir |= PB_SDA)
1963 The code necessary to make the I2C data line tri-stated
1964 (inactive). If the data line is open collector, this
1967 eg: #define I2C_TRISTATE (immr->im_cpm.cp_pbdir &= ~PB_SDA)
1971 Code that returns true if the I2C data line is high,
1974 eg: #define I2C_READ ((immr->im_cpm.cp_pbdat & PB_SDA) != 0)
1978 If <bit> is true, sets the I2C data line high. If it
1979 is false, it clears it (low).
1981 eg: #define I2C_SDA(bit) \
1982 if(bit) immr->im_cpm.cp_pbdat |= PB_SDA; \
1983 else immr->im_cpm.cp_pbdat &= ~PB_SDA
1987 If <bit> is true, sets the I2C clock line high. If it
1988 is false, it clears it (low).
1990 eg: #define I2C_SCL(bit) \
1991 if(bit) immr->im_cpm.cp_pbdat |= PB_SCL; \
1992 else immr->im_cpm.cp_pbdat &= ~PB_SCL
1996 This delay is invoked four times per clock cycle so this
1997 controls the rate of data transfer. The data rate thus
1998 is 1 / (I2C_DELAY * 4). Often defined to be something
2001 #define I2C_DELAY udelay(2)
2003 CONFIG_SOFT_I2C_GPIO_SCL / CONFIG_SOFT_I2C_GPIO_SDA
2005 If your arch supports the generic GPIO framework (asm/gpio.h),
2006 then you may alternatively define the two GPIOs that are to be
2007 used as SCL / SDA. Any of the previous I2C_xxx macros will
2008 have GPIO-based defaults assigned to them as appropriate.
2010 You should define these to the GPIO value as given directly to
2011 the generic GPIO functions.
2013 CONFIG_SYS_I2C_INIT_BOARD
2015 When a board is reset during an i2c bus transfer
2016 chips might think that the current transfer is still
2017 in progress. On some boards it is possible to access
2018 the i2c SCLK line directly, either by using the
2019 processor pin as a GPIO or by having a second pin
2020 connected to the bus. If this option is defined a
2021 custom i2c_init_board() routine in boards/xxx/board.c
2022 is run early in the boot sequence.
2024 CONFIG_SYS_I2C_BOARD_LATE_INIT
2026 An alternative to CONFIG_SYS_I2C_INIT_BOARD. If this option is
2027 defined a custom i2c_board_late_init() routine in
2028 boards/xxx/board.c is run AFTER the operations in i2c_init()
2029 is completed. This callpoint can be used to unreset i2c bus
2030 using CPU i2c controller register accesses for CPUs whose i2c
2031 controller provide such a method. It is called at the end of
2032 i2c_init() to allow i2c_init operations to setup the i2c bus
2033 controller on the CPU (e.g. setting bus speed & slave address).
2035 CONFIG_I2CFAST (PPC405GP|PPC405EP only)
2037 This option enables configuration of bi_iic_fast[] flags
2038 in u-boot bd_info structure based on u-boot environment
2039 variable "i2cfast". (see also i2cfast)
2041 CONFIG_I2C_MULTI_BUS
2043 This option allows the use of multiple I2C buses, each of which
2044 must have a controller. At any point in time, only one bus is
2045 active. To switch to a different bus, use the 'i2c dev' command.
2046 Note that bus numbering is zero-based.
2048 CONFIG_SYS_I2C_NOPROBES
2050 This option specifies a list of I2C devices that will be skipped
2051 when the 'i2c probe' command is issued. If CONFIG_I2C_MULTI_BUS
2052 is set, specify a list of bus-device pairs. Otherwise, specify
2053 a 1D array of device addresses
2056 #undef CONFIG_I2C_MULTI_BUS
2057 #define CONFIG_SYS_I2C_NOPROBES {0x50,0x68}
2059 will skip addresses 0x50 and 0x68 on a board with one I2C bus
2061 #define CONFIG_I2C_MULTI_BUS
2062 #define CONFIG_SYS_I2C_MULTI_NOPROBES {{0,0x50},{0,0x68},{1,0x54}}
2064 will skip addresses 0x50 and 0x68 on bus 0 and address 0x54 on bus 1
2066 CONFIG_SYS_SPD_BUS_NUM
2068 If defined, then this indicates the I2C bus number for DDR SPD.
2069 If not defined, then U-Boot assumes that SPD is on I2C bus 0.
2071 CONFIG_SYS_RTC_BUS_NUM
2073 If defined, then this indicates the I2C bus number for the RTC.
2074 If not defined, then U-Boot assumes that RTC is on I2C bus 0.
2076 CONFIG_SYS_DTT_BUS_NUM
2078 If defined, then this indicates the I2C bus number for the DTT.
2079 If not defined, then U-Boot assumes that DTT is on I2C bus 0.
2081 CONFIG_SYS_I2C_DTT_ADDR:
2083 If defined, specifies the I2C address of the DTT device.
2084 If not defined, then U-Boot uses predefined value for
2085 specified DTT device.
2089 Define this option if you want to use Freescale's I2C driver in
2090 drivers/i2c/fsl_i2c.c.
2094 Define this option if you have I2C devices reached over 1 .. n
2095 I2C Muxes like the pca9544a. This option addes a new I2C
2096 Command "i2c bus [muxtype:muxaddr:muxchannel]" which adds a
2097 new I2C Bus to the existing I2C Busses. If you select the
2098 new Bus with "i2c dev", u-bbot sends first the commandos for
2099 the muxes to activate this new "bus".
2101 CONFIG_I2C_MULTI_BUS must be also defined, to use this
2105 Adding a new I2C Bus reached over 2 pca9544a muxes
2106 The First mux with address 70 and channel 6
2107 The Second mux with address 71 and channel 4
2109 => i2c bus pca9544a:70:6:pca9544a:71:4
2111 Use the "i2c bus" command without parameter, to get a list
2112 of I2C Busses with muxes:
2115 Busses reached over muxes:
2117 reached over Mux(es):
2120 reached over Mux(es):
2125 If you now switch to the new I2C Bus 3 with "i2c dev 3"
2126 u-boot first sends the command to the mux@70 to enable
2127 channel 6, and then the command to the mux@71 to enable
2130 After that, you can use the "normal" i2c commands as
2131 usual to communicate with your I2C devices behind
2134 This option is actually implemented for the bitbanging
2135 algorithm in common/soft_i2c.c and for the Hardware I2C
2136 Bus on the MPC8260. But it should be not so difficult
2137 to add this option to other architectures.
2139 CONFIG_SOFT_I2C_READ_REPEATED_START
2141 defining this will force the i2c_read() function in
2142 the soft_i2c driver to perform an I2C repeated start
2143 between writing the address pointer and reading the
2144 data. If this define is omitted the default behaviour
2145 of doing a stop-start sequence will be used. Most I2C
2146 devices can use either method, but some require one or
2149 - SPI Support: CONFIG_SPI
2151 Enables SPI driver (so far only tested with
2152 SPI EEPROM, also an instance works with Crystal A/D and
2153 D/As on the SACSng board)
2157 Enables the driver for SPI controller on SuperH. Currently
2158 only SH7757 is supported.
2162 Enables extended (16-bit) SPI EEPROM addressing.
2163 (symmetrical to CONFIG_I2C_X)
2167 Enables a software (bit-bang) SPI driver rather than
2168 using hardware support. This is a general purpose
2169 driver that only requires three general I/O port pins
2170 (two outputs, one input) to function. If this is
2171 defined, the board configuration must define several
2172 SPI configuration items (port pins to use, etc). For
2173 an example, see include/configs/sacsng.h.
2177 Enables a hardware SPI driver for general-purpose reads
2178 and writes. As with CONFIG_SOFT_SPI, the board configuration
2179 must define a list of chip-select function pointers.
2180 Currently supported on some MPC8xxx processors. For an
2181 example, see include/configs/mpc8349emds.h.
2185 Enables the driver for the SPI controllers on i.MX and MXC
2186 SoCs. Currently i.MX31/35/51 are supported.
2188 - FPGA Support: CONFIG_FPGA
2190 Enables FPGA subsystem.
2192 CONFIG_FPGA_<vendor>
2194 Enables support for specific chip vendors.
2197 CONFIG_FPGA_<family>
2199 Enables support for FPGA family.
2200 (SPARTAN2, SPARTAN3, VIRTEX2, CYCLONE2, ACEX1K, ACEX)
2204 Specify the number of FPGA devices to support.
2206 CONFIG_SYS_FPGA_PROG_FEEDBACK
2208 Enable printing of hash marks during FPGA configuration.
2210 CONFIG_SYS_FPGA_CHECK_BUSY
2212 Enable checks on FPGA configuration interface busy
2213 status by the configuration function. This option
2214 will require a board or device specific function to
2219 If defined, a function that provides delays in the FPGA
2220 configuration driver.
2222 CONFIG_SYS_FPGA_CHECK_CTRLC
2223 Allow Control-C to interrupt FPGA configuration
2225 CONFIG_SYS_FPGA_CHECK_ERROR
2227 Check for configuration errors during FPGA bitfile
2228 loading. For example, abort during Virtex II
2229 configuration if the INIT_B line goes low (which
2230 indicated a CRC error).
2232 CONFIG_SYS_FPGA_WAIT_INIT
2234 Maximum time to wait for the INIT_B line to deassert
2235 after PROB_B has been deasserted during a Virtex II
2236 FPGA configuration sequence. The default time is 500
2239 CONFIG_SYS_FPGA_WAIT_BUSY
2241 Maximum time to wait for BUSY to deassert during
2242 Virtex II FPGA configuration. The default is 5 ms.
2244 CONFIG_SYS_FPGA_WAIT_CONFIG
2246 Time to wait after FPGA configuration. The default is
2249 - Configuration Management:
2252 If defined, this string will be added to the U-Boot
2253 version information (U_BOOT_VERSION)
2255 - Vendor Parameter Protection:
2257 U-Boot considers the values of the environment
2258 variables "serial#" (Board Serial Number) and
2259 "ethaddr" (Ethernet Address) to be parameters that
2260 are set once by the board vendor / manufacturer, and
2261 protects these variables from casual modification by
2262 the user. Once set, these variables are read-only,
2263 and write or delete attempts are rejected. You can
2264 change this behaviour:
2266 If CONFIG_ENV_OVERWRITE is #defined in your config
2267 file, the write protection for vendor parameters is
2268 completely disabled. Anybody can change or delete
2271 Alternatively, if you #define _both_ CONFIG_ETHADDR
2272 _and_ CONFIG_OVERWRITE_ETHADDR_ONCE, a default
2273 Ethernet address is installed in the environment,
2274 which can be changed exactly ONCE by the user. [The
2275 serial# is unaffected by this, i. e. it remains
2278 The same can be accomplished in a more flexible way
2279 for any variable by configuring the type of access
2280 to allow for those variables in the ".flags" variable
2281 or define CONFIG_ENV_FLAGS_LIST_STATIC.
2286 Define this variable to enable the reservation of
2287 "protected RAM", i. e. RAM which is not overwritten
2288 by U-Boot. Define CONFIG_PRAM to hold the number of
2289 kB you want to reserve for pRAM. You can overwrite
2290 this default value by defining an environment
2291 variable "pram" to the number of kB you want to
2292 reserve. Note that the board info structure will
2293 still show the full amount of RAM. If pRAM is
2294 reserved, a new environment variable "mem" will
2295 automatically be defined to hold the amount of
2296 remaining RAM in a form that can be passed as boot
2297 argument to Linux, for instance like that:
2299 setenv bootargs ... mem=\${mem}
2302 This way you can tell Linux not to use this memory,
2303 either, which results in a memory region that will
2304 not be affected by reboots.
2306 *WARNING* If your board configuration uses automatic
2307 detection of the RAM size, you must make sure that
2308 this memory test is non-destructive. So far, the
2309 following board configurations are known to be
2312 IVMS8, IVML24, SPD8xx, TQM8xxL,
2313 HERMES, IP860, RPXlite, LWMON,
2316 - Access to physical memory region (> 4GB)
2317 Some basic support is provided for operations on memory not
2318 normally accessible to U-Boot - e.g. some architectures
2319 support access to more than 4GB of memory on 32-bit
2320 machines using physical address extension or similar.
2321 Define CONFIG_PHYSMEM to access this basic support, which
2322 currently only supports clearing the memory.
2327 Define this variable to stop the system in case of a
2328 fatal error, so that you have to reset it manually.
2329 This is probably NOT a good idea for an embedded
2330 system where you want the system to reboot
2331 automatically as fast as possible, but it may be
2332 useful during development since you can try to debug
2333 the conditions that lead to the situation.
2335 CONFIG_NET_RETRY_COUNT
2337 This variable defines the number of retries for
2338 network operations like ARP, RARP, TFTP, or BOOTP
2339 before giving up the operation. If not defined, a
2340 default value of 5 is used.
2344 Timeout waiting for an ARP reply in milliseconds.
2348 Timeout in milliseconds used in NFS protocol.
2349 If you encounter "ERROR: Cannot umount" in nfs command,
2350 try longer timeout such as
2351 #define CONFIG_NFS_TIMEOUT 10000UL
2353 - Command Interpreter:
2354 CONFIG_AUTO_COMPLETE
2356 Enable auto completion of commands using TAB.
2358 Note that this feature has NOT been implemented yet
2359 for the "hush" shell.
2362 CONFIG_SYS_HUSH_PARSER
2364 Define this variable to enable the "hush" shell (from
2365 Busybox) as command line interpreter, thus enabling
2366 powerful command line syntax like
2367 if...then...else...fi conditionals or `&&' and '||'
2368 constructs ("shell scripts").
2370 If undefined, you get the old, much simpler behaviour
2371 with a somewhat smaller memory footprint.
2374 CONFIG_SYS_PROMPT_HUSH_PS2
2376 This defines the secondary prompt string, which is
2377 printed when the command interpreter needs more input
2378 to complete a command. Usually "> ".
2382 In the current implementation, the local variables
2383 space and global environment variables space are
2384 separated. Local variables are those you define by
2385 simply typing `name=value'. To access a local
2386 variable later on, you have write `$name' or
2387 `${name}'; to execute the contents of a variable
2388 directly type `$name' at the command prompt.
2390 Global environment variables are those you use
2391 setenv/printenv to work with. To run a command stored
2392 in such a variable, you need to use the run command,
2393 and you must not use the '$' sign to access them.
2395 To store commands and special characters in a
2396 variable, please use double quotation marks
2397 surrounding the whole text of the variable, instead
2398 of the backslashes before semicolons and special
2401 - Commandline Editing and History:
2402 CONFIG_CMDLINE_EDITING
2404 Enable editing and History functions for interactive
2405 commandline input operations
2407 - Default Environment:
2408 CONFIG_EXTRA_ENV_SETTINGS
2410 Define this to contain any number of null terminated
2411 strings (variable = value pairs) that will be part of
2412 the default environment compiled into the boot image.
2414 For example, place something like this in your
2415 board's config file:
2417 #define CONFIG_EXTRA_ENV_SETTINGS \
2421 Warning: This method is based on knowledge about the
2422 internal format how the environment is stored by the
2423 U-Boot code. This is NOT an official, exported
2424 interface! Although it is unlikely that this format
2425 will change soon, there is no guarantee either.
2426 You better know what you are doing here.
2428 Note: overly (ab)use of the default environment is
2429 discouraged. Make sure to check other ways to preset
2430 the environment like the "source" command or the
2433 CONFIG_ENV_VARS_UBOOT_CONFIG
2435 Define this in order to add variables describing the
2436 U-Boot build configuration to the default environment.
2437 These will be named arch, cpu, board, vendor, and soc.
2439 Enabling this option will cause the following to be defined:
2447 CONFIG_ENV_VARS_UBOOT_RUNTIME_CONFIG
2449 Define this in order to add variables describing certain
2450 run-time determined information about the hardware to the
2451 environment. These will be named board_name, board_rev.
2453 CONFIG_DELAY_ENVIRONMENT
2455 Normally the environment is loaded when the board is
2456 intialised so that it is available to U-Boot. This inhibits
2457 that so that the environment is not available until
2458 explicitly loaded later by U-Boot code. With CONFIG_OF_CONTROL
2459 this is instead controlled by the value of
2460 /config/load-environment.
2462 - DataFlash Support:
2463 CONFIG_HAS_DATAFLASH
2465 Defining this option enables DataFlash features and
2466 allows to read/write in Dataflash via the standard
2469 - Serial Flash support
2472 Defining this option enables SPI flash commands
2473 'sf probe/read/write/erase/update'.
2475 Usage requires an initial 'probe' to define the serial
2476 flash parameters, followed by read/write/erase/update
2479 The following defaults may be provided by the platform
2480 to handle the common case when only a single serial
2481 flash is present on the system.
2483 CONFIG_SF_DEFAULT_BUS Bus identifier
2484 CONFIG_SF_DEFAULT_CS Chip-select
2485 CONFIG_SF_DEFAULT_MODE (see include/spi.h)
2486 CONFIG_SF_DEFAULT_SPEED in Hz
2490 Define this option to include a destructive SPI flash
2493 - SystemACE Support:
2496 Adding this option adds support for Xilinx SystemACE
2497 chips attached via some sort of local bus. The address
2498 of the chip must also be defined in the
2499 CONFIG_SYS_SYSTEMACE_BASE macro. For example:
2501 #define CONFIG_SYSTEMACE
2502 #define CONFIG_SYS_SYSTEMACE_BASE 0xf0000000
2504 When SystemACE support is added, the "ace" device type
2505 becomes available to the fat commands, i.e. fatls.
2507 - TFTP Fixed UDP Port:
2510 If this is defined, the environment variable tftpsrcp
2511 is used to supply the TFTP UDP source port value.
2512 If tftpsrcp isn't defined, the normal pseudo-random port
2513 number generator is used.
2515 Also, the environment variable tftpdstp is used to supply
2516 the TFTP UDP destination port value. If tftpdstp isn't
2517 defined, the normal port 69 is used.
2519 The purpose for tftpsrcp is to allow a TFTP server to
2520 blindly start the TFTP transfer using the pre-configured
2521 target IP address and UDP port. This has the effect of
2522 "punching through" the (Windows XP) firewall, allowing
2523 the remainder of the TFTP transfer to proceed normally.
2524 A better solution is to properly configure the firewall,
2525 but sometimes that is not allowed.
2530 This enables a generic 'hash' command which can produce
2531 hashes / digests from a few algorithms (e.g. SHA1, SHA256).
2535 Enable the hash verify command (hash -v). This adds to code
2538 CONFIG_SHA1 - support SHA1 hashing
2539 CONFIG_SHA256 - support SHA256 hashing
2541 Note: There is also a sha1sum command, which should perhaps
2542 be deprecated in favour of 'hash sha1'.
2544 - Show boot progress:
2545 CONFIG_SHOW_BOOT_PROGRESS
2547 Defining this option allows to add some board-
2548 specific code (calling a user-provided function
2549 "show_boot_progress(int)") that enables you to show
2550 the system's boot progress on some display (for
2551 example, some LED's) on your board. At the moment,
2552 the following checkpoints are implemented:
2554 - Detailed boot stage timing
2556 Define this option to get detailed timing of each stage
2557 of the boot process.
2559 CONFIG_BOOTSTAGE_USER_COUNT
2560 This is the number of available user bootstage records.
2561 Each time you call bootstage_mark(BOOTSTAGE_ID_ALLOC, ...)
2562 a new ID will be allocated from this stash. If you exceed
2563 the limit, recording will stop.
2565 CONFIG_BOOTSTAGE_REPORT
2566 Define this to print a report before boot, similar to this:
2568 Timer summary in microseconds:
2571 3,575,678 3,575,678 board_init_f start
2572 3,575,695 17 arch_cpu_init A9
2573 3,575,777 82 arch_cpu_init done
2574 3,659,598 83,821 board_init_r start
2575 3,910,375 250,777 main_loop
2576 29,916,167 26,005,792 bootm_start
2577 30,361,327 445,160 start_kernel
2579 CONFIG_CMD_BOOTSTAGE
2580 Add a 'bootstage' command which supports printing a report
2581 and un/stashing of bootstage data.
2583 CONFIG_BOOTSTAGE_FDT
2584 Stash the bootstage information in the FDT. A root 'bootstage'
2585 node is created with each bootstage id as a child. Each child
2586 has a 'name' property and either 'mark' containing the
2587 mark time in microsecond, or 'accum' containing the
2588 accumulated time for that bootstage id in microseconds.
2593 name = "board_init_f";
2602 Code in the Linux kernel can find this in /proc/devicetree.
2604 Legacy uImage format:
2607 1 common/cmd_bootm.c before attempting to boot an image
2608 -1 common/cmd_bootm.c Image header has bad magic number
2609 2 common/cmd_bootm.c Image header has correct magic number
2610 -2 common/cmd_bootm.c Image header has bad checksum
2611 3 common/cmd_bootm.c Image header has correct checksum
2612 -3 common/cmd_bootm.c Image data has bad checksum
2613 4 common/cmd_bootm.c Image data has correct checksum
2614 -4 common/cmd_bootm.c Image is for unsupported architecture
2615 5 common/cmd_bootm.c Architecture check OK
2616 -5 common/cmd_bootm.c Wrong Image Type (not kernel, multi)
2617 6 common/cmd_bootm.c Image Type check OK
2618 -6 common/cmd_bootm.c gunzip uncompression error
2619 -7 common/cmd_bootm.c Unimplemented compression type
2620 7 common/cmd_bootm.c Uncompression OK
2621 8 common/cmd_bootm.c No uncompress/copy overwrite error
2622 -9 common/cmd_bootm.c Unsupported OS (not Linux, BSD, VxWorks, QNX)
2624 9 common/image.c Start initial ramdisk verification
2625 -10 common/image.c Ramdisk header has bad magic number
2626 -11 common/image.c Ramdisk header has bad checksum
2627 10 common/image.c Ramdisk header is OK
2628 -12 common/image.c Ramdisk data has bad checksum
2629 11 common/image.c Ramdisk data has correct checksum
2630 12 common/image.c Ramdisk verification complete, start loading
2631 -13 common/image.c Wrong Image Type (not PPC Linux ramdisk)
2632 13 common/image.c Start multifile image verification
2633 14 common/image.c No initial ramdisk, no multifile, continue.
2635 15 arch/<arch>/lib/bootm.c All preparation done, transferring control to OS
2637 -30 arch/powerpc/lib/board.c Fatal error, hang the system
2638 -31 post/post.c POST test failed, detected by post_output_backlog()
2639 -32 post/post.c POST test failed, detected by post_run_single()
2641 34 common/cmd_doc.c before loading a Image from a DOC device
2642 -35 common/cmd_doc.c Bad usage of "doc" command
2643 35 common/cmd_doc.c correct usage of "doc" command
2644 -36 common/cmd_doc.c No boot device
2645 36 common/cmd_doc.c correct boot device
2646 -37 common/cmd_doc.c Unknown Chip ID on boot device
2647 37 common/cmd_doc.c correct chip ID found, device available
2648 -38 common/cmd_doc.c Read Error on boot device
2649 38 common/cmd_doc.c reading Image header from DOC device OK
2650 -39 common/cmd_doc.c Image header has bad magic number
2651 39 common/cmd_doc.c Image header has correct magic number
2652 -40 common/cmd_doc.c Error reading Image from DOC device
2653 40 common/cmd_doc.c Image header has correct magic number
2654 41 common/cmd_ide.c before loading a Image from a IDE device
2655 -42 common/cmd_ide.c Bad usage of "ide" command
2656 42 common/cmd_ide.c correct usage of "ide" command
2657 -43 common/cmd_ide.c No boot device
2658 43 common/cmd_ide.c boot device found
2659 -44 common/cmd_ide.c Device not available
2660 44 common/cmd_ide.c Device available
2661 -45 common/cmd_ide.c wrong partition selected
2662 45 common/cmd_ide.c partition selected
2663 -46 common/cmd_ide.c Unknown partition table
2664 46 common/cmd_ide.c valid partition table found
2665 -47 common/cmd_ide.c Invalid partition type
2666 47 common/cmd_ide.c correct partition type
2667 -48 common/cmd_ide.c Error reading Image Header on boot device
2668 48 common/cmd_ide.c reading Image Header from IDE device OK
2669 -49 common/cmd_ide.c Image header has bad magic number
2670 49 common/cmd_ide.c Image header has correct magic number
2671 -50 common/cmd_ide.c Image header has bad checksum
2672 50 common/cmd_ide.c Image header has correct checksum
2673 -51 common/cmd_ide.c Error reading Image from IDE device
2674 51 common/cmd_ide.c reading Image from IDE device OK
2675 52 common/cmd_nand.c before loading a Image from a NAND device
2676 -53 common/cmd_nand.c Bad usage of "nand" command
2677 53 common/cmd_nand.c correct usage of "nand" command
2678 -54 common/cmd_nand.c No boot device
2679 54 common/cmd_nand.c boot device found
2680 -55 common/cmd_nand.c Unknown Chip ID on boot device
2681 55 common/cmd_nand.c correct chip ID found, device available
2682 -56 common/cmd_nand.c Error reading Image Header on boot device
2683 56 common/cmd_nand.c reading Image Header from NAND device OK
2684 -57 common/cmd_nand.c Image header has bad magic number
2685 57 common/cmd_nand.c Image header has correct magic number
2686 -58 common/cmd_nand.c Error reading Image from NAND device
2687 58 common/cmd_nand.c reading Image from NAND device OK
2689 -60 common/env_common.c Environment has a bad CRC, using default
2691 64 net/eth.c starting with Ethernet configuration.
2692 -64 net/eth.c no Ethernet found.
2693 65 net/eth.c Ethernet found.
2695 -80 common/cmd_net.c usage wrong
2696 80 common/cmd_net.c before calling NetLoop()
2697 -81 common/cmd_net.c some error in NetLoop() occurred
2698 81 common/cmd_net.c NetLoop() back without error
2699 -82 common/cmd_net.c size == 0 (File with size 0 loaded)
2700 82 common/cmd_net.c trying automatic boot
2701 83 common/cmd_net.c running "source" command
2702 -83 common/cmd_net.c some error in automatic boot or "source" command
2703 84 common/cmd_net.c end without errors
2708 100 common/cmd_bootm.c Kernel FIT Image has correct format
2709 -100 common/cmd_bootm.c Kernel FIT Image has incorrect format
2710 101 common/cmd_bootm.c No Kernel subimage unit name, using configuration
2711 -101 common/cmd_bootm.c Can't get configuration for kernel subimage
2712 102 common/cmd_bootm.c Kernel unit name specified
2713 -103 common/cmd_bootm.c Can't get kernel subimage node offset
2714 103 common/cmd_bootm.c Found configuration node
2715 104 common/cmd_bootm.c Got kernel subimage node offset
2716 -104 common/cmd_bootm.c Kernel subimage hash verification failed
2717 105 common/cmd_bootm.c Kernel subimage hash verification OK
2718 -105 common/cmd_bootm.c Kernel subimage is for unsupported architecture
2719 106 common/cmd_bootm.c Architecture check OK
2720 -106 common/cmd_bootm.c Kernel subimage has wrong type
2721 107 common/cmd_bootm.c Kernel subimage type OK
2722 -107 common/cmd_bootm.c Can't get kernel subimage data/size
2723 108 common/cmd_bootm.c Got kernel subimage data/size
2724 -108 common/cmd_bootm.c Wrong image type (not legacy, FIT)
2725 -109 common/cmd_bootm.c Can't get kernel subimage type
2726 -110 common/cmd_bootm.c Can't get kernel subimage comp
2727 -111 common/cmd_bootm.c Can't get kernel subimage os
2728 -112 common/cmd_bootm.c Can't get kernel subimage load address
2729 -113 common/cmd_bootm.c Image uncompress/copy overwrite error
2731 120 common/image.c Start initial ramdisk verification
2732 -120 common/image.c Ramdisk FIT image has incorrect format
2733 121 common/image.c Ramdisk FIT image has correct format
2734 122 common/image.c No ramdisk subimage unit name, using configuration
2735 -122 common/image.c Can't get configuration for ramdisk subimage
2736 123 common/image.c Ramdisk unit name specified
2737 -124 common/image.c Can't get ramdisk subimage node offset
2738 125 common/image.c Got ramdisk subimage node offset
2739 -125 common/image.c Ramdisk subimage hash verification failed
2740 126 common/image.c Ramdisk subimage hash verification OK
2741 -126 common/image.c Ramdisk subimage for unsupported architecture
2742 127 common/image.c Architecture check OK
2743 -127 common/image.c Can't get ramdisk subimage data/size
2744 128 common/image.c Got ramdisk subimage data/size
2745 129 common/image.c Can't get ramdisk load address
2746 -129 common/image.c Got ramdisk load address
2748 -130 common/cmd_doc.c Incorrect FIT image format
2749 131 common/cmd_doc.c FIT image format OK
2751 -140 common/cmd_ide.c Incorrect FIT image format
2752 141 common/cmd_ide.c FIT image format OK
2754 -150 common/cmd_nand.c Incorrect FIT image format
2755 151 common/cmd_nand.c FIT image format OK
2757 - FIT image support:
2759 Enable support for the FIT uImage format.
2761 CONFIG_FIT_BEST_MATCH
2762 When no configuration is explicitly selected, default to the
2763 one whose fdt's compatibility field best matches that of
2764 U-Boot itself. A match is considered "best" if it matches the
2765 most specific compatibility entry of U-Boot's fdt's root node.
2766 The order of entries in the configuration's fdt is ignored.
2768 - Standalone program support:
2769 CONFIG_STANDALONE_LOAD_ADDR
2771 This option defines a board specific value for the
2772 address where standalone program gets loaded, thus
2773 overwriting the architecture dependent default
2776 - Frame Buffer Address:
2779 Define CONFIG_FB_ADDR if you want to use specific
2780 address for frame buffer. This is typically the case
2781 when using a graphics controller has separate video
2782 memory. U-Boot will then place the frame buffer at
2783 the given address instead of dynamically reserving it
2784 in system RAM by calling lcd_setmem(), which grabs
2785 the memory for the frame buffer depending on the
2786 configured panel size.
2788 Please see board_init_f function.
2790 - Automatic software updates via TFTP server
2792 CONFIG_UPDATE_TFTP_CNT_MAX
2793 CONFIG_UPDATE_TFTP_MSEC_MAX
2795 These options enable and control the auto-update feature;
2796 for a more detailed description refer to doc/README.update.
2798 - MTD Support (mtdparts command, UBI support)
2801 Adds the MTD device infrastructure from the Linux kernel.
2802 Needed for mtdparts command support.
2804 CONFIG_MTD_PARTITIONS
2806 Adds the MTD partitioning infrastructure from the Linux
2807 kernel. Needed for UBI support.
2812 Adds commands for interacting with MTD partitions formatted
2813 with the UBI flash translation layer
2815 Requires also defining CONFIG_RBTREE
2817 CONFIG_UBI_SILENCE_MSG
2819 Make the verbose messages from UBI stop printing. This leaves
2820 warnings and errors enabled.
2825 Adds commands for interacting with UBI volumes formatted as
2826 UBIFS. UBIFS is read-only in u-boot.
2828 Requires UBI support as well as CONFIG_LZO
2830 CONFIG_UBIFS_SILENCE_MSG
2832 Make the verbose messages from UBIFS stop printing. This leaves
2833 warnings and errors enabled.
2837 Enable building of SPL globally.
2840 LDSCRIPT for linking the SPL binary.
2843 Maximum binary size (text, data and rodata) of the SPL binary.
2845 CONFIG_SPL_TEXT_BASE
2846 TEXT_BASE for linking the SPL binary.
2848 CONFIG_SPL_RELOC_TEXT_BASE
2849 Address to relocate to. If unspecified, this is equal to
2850 CONFIG_SPL_TEXT_BASE (i.e. no relocation is done).
2852 CONFIG_SPL_BSS_START_ADDR
2853 Link address for the BSS within the SPL binary.
2855 CONFIG_SPL_BSS_MAX_SIZE
2856 Maximum binary size of the BSS section of the SPL binary.
2859 Adress of the start of the stack SPL will use
2861 CONFIG_SPL_RELOC_STACK
2862 Adress of the start of the stack SPL will use after
2863 relocation. If unspecified, this is equal to
2866 CONFIG_SYS_SPL_MALLOC_START
2867 Starting address of the malloc pool used in SPL.
2869 CONFIG_SYS_SPL_MALLOC_SIZE
2870 The size of the malloc pool used in SPL.
2872 CONFIG_SPL_FRAMEWORK
2873 Enable the SPL framework under common/. This framework
2874 supports MMC, NAND and YMODEM loading of U-Boot and NAND
2875 NAND loading of the Linux Kernel.
2877 CONFIG_SPL_DISPLAY_PRINT
2878 For ARM, enable an optional function to print more information
2879 about the running system.
2881 CONFIG_SPL_INIT_MINIMAL
2882 Arch init code should be built for a very small image
2884 CONFIG_SPL_LIBCOMMON_SUPPORT
2885 Support for common/libcommon.o in SPL binary
2887 CONFIG_SPL_LIBDISK_SUPPORT
2888 Support for disk/libdisk.o in SPL binary
2890 CONFIG_SPL_I2C_SUPPORT
2891 Support for drivers/i2c/libi2c.o in SPL binary
2893 CONFIG_SPL_GPIO_SUPPORT
2894 Support for drivers/gpio/libgpio.o in SPL binary
2896 CONFIG_SPL_MMC_SUPPORT
2897 Support for drivers/mmc/libmmc.o in SPL binary
2899 CONFIG_SYS_MMCSD_RAW_MODE_U_BOOT_SECTOR,
2900 CONFIG_SYS_U_BOOT_MAX_SIZE_SECTORS,
2901 CONFIG_SYS_MMC_SD_FAT_BOOT_PARTITION
2902 Address, size and partition on the MMC to load U-Boot from
2903 when the MMC is being used in raw mode.
2905 CONFIG_SPL_FAT_SUPPORT
2906 Support for fs/fat/libfat.o in SPL binary
2908 CONFIG_SPL_FAT_LOAD_PAYLOAD_NAME
2909 Filename to read to load U-Boot when reading from FAT
2911 CONFIG_SPL_MPC83XX_WAIT_FOR_NAND
2912 Set this for NAND SPL on PPC mpc83xx targets, so that
2913 start.S waits for the rest of the SPL to load before
2914 continuing (the hardware starts execution after just
2915 loading the first page rather than the full 4K).
2917 CONFIG_SPL_NAND_BASE
2918 Include nand_base.c in the SPL. Requires
2919 CONFIG_SPL_NAND_DRIVERS.
2921 CONFIG_SPL_NAND_DRIVERS
2922 SPL uses normal NAND drivers, not minimal drivers.
2925 Include standard software ECC in the SPL
2927 CONFIG_SPL_NAND_SIMPLE
2928 Support for NAND boot using simple NAND drivers that
2929 expose the cmd_ctrl() interface.
2931 CONFIG_SYS_NAND_5_ADDR_CYCLE, CONFIG_SYS_NAND_PAGE_COUNT,
2932 CONFIG_SYS_NAND_PAGE_SIZE, CONFIG_SYS_NAND_OOBSIZE,
2933 CONFIG_SYS_NAND_BLOCK_SIZE, CONFIG_SYS_NAND_BAD_BLOCK_POS,
2934 CONFIG_SYS_NAND_ECCPOS, CONFIG_SYS_NAND_ECCSIZE,
2935 CONFIG_SYS_NAND_ECCBYTES
2936 Defines the size and behavior of the NAND that SPL uses
2939 CONFIG_SYS_NAND_U_BOOT_OFFS
2940 Location in NAND to read U-Boot from
2942 CONFIG_SYS_NAND_U_BOOT_DST
2943 Location in memory to load U-Boot to
2945 CONFIG_SYS_NAND_U_BOOT_SIZE
2946 Size of image to load
2948 CONFIG_SYS_NAND_U_BOOT_START
2949 Entry point in loaded image to jump to
2951 CONFIG_SYS_NAND_HW_ECC_OOBFIRST
2952 Define this if you need to first read the OOB and then the
2953 data. This is used for example on davinci plattforms.
2955 CONFIG_SPL_OMAP3_ID_NAND
2956 Support for an OMAP3-specific set of functions to return the
2957 ID and MFR of the first attached NAND chip, if present.
2959 CONFIG_SPL_SERIAL_SUPPORT
2960 Support for drivers/serial/libserial.o in SPL binary
2962 CONFIG_SPL_SPI_FLASH_SUPPORT
2963 Support for drivers/mtd/spi/libspi_flash.o in SPL binary
2965 CONFIG_SPL_SPI_SUPPORT
2966 Support for drivers/spi/libspi.o in SPL binary
2968 CONFIG_SPL_RAM_DEVICE
2969 Support for running image already present in ram, in SPL binary
2971 CONFIG_SPL_LIBGENERIC_SUPPORT
2972 Support for lib/libgeneric.o in SPL binary
2975 Linker address to which the SPL should be padded before
2976 appending the SPL payload.
2979 Final target image containing SPL and payload. Some SPLs
2980 use an arch-specific makefile fragment instead, for
2981 example if more than one image needs to be produced.
2986 [so far only for SMDK2400 boards]
2988 - Modem support enable:
2989 CONFIG_MODEM_SUPPORT
2991 - RTS/CTS Flow control enable:
2994 - Modem debug support:
2995 CONFIG_MODEM_SUPPORT_DEBUG
2997 Enables debugging stuff (char screen[1024], dbg())
2998 for modem support. Useful only with BDI2000.
3000 - Interrupt support (PPC):
3002 There are common interrupt_init() and timer_interrupt()
3003 for all PPC archs. interrupt_init() calls interrupt_init_cpu()
3004 for CPU specific initialization. interrupt_init_cpu()
3005 should set decrementer_count to appropriate value. If
3006 CPU resets decrementer automatically after interrupt
3007 (ppc4xx) it should set decrementer_count to zero.
3008 timer_interrupt() calls timer_interrupt_cpu() for CPU
3009 specific handling. If board has watchdog / status_led
3010 / other_activity_monitor it works automatically from
3011 general timer_interrupt().
3015 In the target system modem support is enabled when a
3016 specific key (key combination) is pressed during
3017 power-on. Otherwise U-Boot will boot normally
3018 (autoboot). The key_pressed() function is called from
3019 board_init(). Currently key_pressed() is a dummy
3020 function, returning 1 and thus enabling modem
3023 If there are no modem init strings in the
3024 environment, U-Boot proceed to autoboot; the
3025 previous output (banner, info printfs) will be
3028 See also: doc/README.Modem
3030 Board initialization settings:
3031 ------------------------------
3033 During Initialization u-boot calls a number of board specific functions
3034 to allow the preparation of board specific prerequisites, e.g. pin setup
3035 before drivers are initialized. To enable these callbacks the
3036 following configuration macros have to be defined. Currently this is
3037 architecture specific, so please check arch/your_architecture/lib/board.c
3038 typically in board_init_f() and board_init_r().
3040 - CONFIG_BOARD_EARLY_INIT_F: Call board_early_init_f()
3041 - CONFIG_BOARD_EARLY_INIT_R: Call board_early_init_r()
3042 - CONFIG_BOARD_LATE_INIT: Call board_late_init()
3043 - CONFIG_BOARD_POSTCLK_INIT: Call board_postclk_init()
3045 Configuration Settings:
3046 -----------------------
3048 - CONFIG_SYS_LONGHELP: Defined when you want long help messages included;
3049 undefine this when you're short of memory.
3051 - CONFIG_SYS_HELP_CMD_WIDTH: Defined when you want to override the default
3052 width of the commands listed in the 'help' command output.
3054 - CONFIG_SYS_PROMPT: This is what U-Boot prints on the console to
3055 prompt for user input.
3057 - CONFIG_SYS_CBSIZE: Buffer size for input from the Console
3059 - CONFIG_SYS_PBSIZE: Buffer size for Console output
3061 - CONFIG_SYS_MAXARGS: max. Number of arguments accepted for monitor commands
3063 - CONFIG_SYS_BARGSIZE: Buffer size for Boot Arguments which are passed to
3064 the application (usually a Linux kernel) when it is
3067 - CONFIG_SYS_BAUDRATE_TABLE:
3068 List of legal baudrate settings for this board.
3070 - CONFIG_SYS_CONSOLE_INFO_QUIET
3071 Suppress display of console information at boot.
3073 - CONFIG_SYS_CONSOLE_IS_IN_ENV
3074 If the board specific function
3075 extern int overwrite_console (void);
3076 returns 1, the stdin, stderr and stdout are switched to the
3077 serial port, else the settings in the environment are used.
3079 - CONFIG_SYS_CONSOLE_OVERWRITE_ROUTINE
3080 Enable the call to overwrite_console().
3082 - CONFIG_SYS_CONSOLE_ENV_OVERWRITE
3083 Enable overwrite of previous console environment settings.
3085 - CONFIG_SYS_MEMTEST_START, CONFIG_SYS_MEMTEST_END:
3086 Begin and End addresses of the area used by the
3089 - CONFIG_SYS_ALT_MEMTEST:
3090 Enable an alternate, more extensive memory test.
3092 - CONFIG_SYS_MEMTEST_SCRATCH:
3093 Scratch address used by the alternate memory test
3094 You only need to set this if address zero isn't writeable
3096 - CONFIG_SYS_MEM_TOP_HIDE (PPC only):
3097 If CONFIG_SYS_MEM_TOP_HIDE is defined in the board config header,
3098 this specified memory area will get subtracted from the top
3099 (end) of RAM and won't get "touched" at all by U-Boot. By
3100 fixing up gd->ram_size the Linux kernel should gets passed
3101 the now "corrected" memory size and won't touch it either.
3102 This should work for arch/ppc and arch/powerpc. Only Linux
3103 board ports in arch/powerpc with bootwrapper support that
3104 recalculate the memory size from the SDRAM controller setup
3105 will have to get fixed in Linux additionally.
3107 This option can be used as a workaround for the 440EPx/GRx
3108 CHIP 11 errata where the last 256 bytes in SDRAM shouldn't
3111 WARNING: Please make sure that this value is a multiple of
3112 the Linux page size (normally 4k). If this is not the case,
3113 then the end address of the Linux memory will be located at a
3114 non page size aligned address and this could cause major
3117 - CONFIG_SYS_LOADS_BAUD_CHANGE:
3118 Enable temporary baudrate change while serial download
3120 - CONFIG_SYS_SDRAM_BASE:
3121 Physical start address of SDRAM. _Must_ be 0 here.
3123 - CONFIG_SYS_MBIO_BASE:
3124 Physical start address of Motherboard I/O (if using a
3127 - CONFIG_SYS_FLASH_BASE:
3128 Physical start address of Flash memory.
3130 - CONFIG_SYS_MONITOR_BASE:
3131 Physical start address of boot monitor code (set by
3132 make config files to be same as the text base address
3133 (CONFIG_SYS_TEXT_BASE) used when linking) - same as
3134 CONFIG_SYS_FLASH_BASE when booting from flash.
3136 - CONFIG_SYS_MONITOR_LEN:
3137 Size of memory reserved for monitor code, used to
3138 determine _at_compile_time_ (!) if the environment is
3139 embedded within the U-Boot image, or in a separate
3142 - CONFIG_SYS_MALLOC_LEN:
3143 Size of DRAM reserved for malloc() use.
3145 - CONFIG_SYS_BOOTM_LEN:
3146 Normally compressed uImages are limited to an
3147 uncompressed size of 8 MBytes. If this is not enough,
3148 you can define CONFIG_SYS_BOOTM_LEN in your board config file
3149 to adjust this setting to your needs.
3151 - CONFIG_SYS_BOOTMAPSZ:
3152 Maximum size of memory mapped by the startup code of
3153 the Linux kernel; all data that must be processed by
3154 the Linux kernel (bd_info, boot arguments, FDT blob if
3155 used) must be put below this limit, unless "bootm_low"
3156 enviroment variable is defined and non-zero. In such case
3157 all data for the Linux kernel must be between "bootm_low"
3158 and "bootm_low" + CONFIG_SYS_BOOTMAPSZ. The environment
3159 variable "bootm_mapsize" will override the value of
3160 CONFIG_SYS_BOOTMAPSZ. If CONFIG_SYS_BOOTMAPSZ is undefined,
3161 then the value in "bootm_size" will be used instead.
3163 - CONFIG_SYS_BOOT_RAMDISK_HIGH:
3164 Enable initrd_high functionality. If defined then the
3165 initrd_high feature is enabled and the bootm ramdisk subcommand
3168 - CONFIG_SYS_BOOT_GET_CMDLINE:
3169 Enables allocating and saving kernel cmdline in space between
3170 "bootm_low" and "bootm_low" + BOOTMAPSZ.
3172 - CONFIG_SYS_BOOT_GET_KBD:
3173 Enables allocating and saving a kernel copy of the bd_info in
3174 space between "bootm_low" and "bootm_low" + BOOTMAPSZ.
3176 - CONFIG_SYS_MAX_FLASH_BANKS:
3177 Max number of Flash memory banks
3179 - CONFIG_SYS_MAX_FLASH_SECT:
3180 Max number of sectors on a Flash chip
3182 - CONFIG_SYS_FLASH_ERASE_TOUT:
3183 Timeout for Flash erase operations (in ms)
3185 - CONFIG_SYS_FLASH_WRITE_TOUT:
3186 Timeout for Flash write operations (in ms)
3188 - CONFIG_SYS_FLASH_LOCK_TOUT
3189 Timeout for Flash set sector lock bit operation (in ms)
3191 - CONFIG_SYS_FLASH_UNLOCK_TOUT
3192 Timeout for Flash clear lock bits operation (in ms)
3194 - CONFIG_SYS_FLASH_PROTECTION
3195 If defined, hardware flash sectors protection is used
3196 instead of U-Boot software protection.
3198 - CONFIG_SYS_DIRECT_FLASH_TFTP:
3200 Enable TFTP transfers directly to flash memory;
3201 without this option such a download has to be
3202 performed in two steps: (1) download to RAM, and (2)
3203 copy from RAM to flash.
3205 The two-step approach is usually more reliable, since
3206 you can check if the download worked before you erase
3207 the flash, but in some situations (when system RAM is
3208 too limited to allow for a temporary copy of the
3209 downloaded image) this option may be very useful.
3211 - CONFIG_SYS_FLASH_CFI:
3212 Define if the flash driver uses extra elements in the
3213 common flash structure for storing flash geometry.
3215 - CONFIG_FLASH_CFI_DRIVER
3216 This option also enables the building of the cfi_flash driver
3217 in the drivers directory
3219 - CONFIG_FLASH_CFI_MTD
3220 This option enables the building of the cfi_mtd driver
3221 in the drivers directory. The driver exports CFI flash
3224 - CONFIG_SYS_FLASH_USE_BUFFER_WRITE
3225 Use buffered writes to flash.
3227 - CONFIG_FLASH_SPANSION_S29WS_N
3228 s29ws-n MirrorBit flash has non-standard addresses for buffered
3231 - CONFIG_SYS_FLASH_QUIET_TEST
3232 If this option is defined, the common CFI flash doesn't
3233 print it's warning upon not recognized FLASH banks. This
3234 is useful, if some of the configured banks are only
3235 optionally available.
3237 - CONFIG_FLASH_SHOW_PROGRESS
3238 If defined (must be an integer), print out countdown
3239 digits and dots. Recommended value: 45 (9..1) for 80
3240 column displays, 15 (3..1) for 40 column displays.
3242 - CONFIG_SYS_RX_ETH_BUFFER:
3243 Defines the number of Ethernet receive buffers. On some
3244 Ethernet controllers it is recommended to set this value
3245 to 8 or even higher (EEPRO100 or 405 EMAC), since all
3246 buffers can be full shortly after enabling the interface
3247 on high Ethernet traffic.
3248 Defaults to 4 if not defined.
3250 - CONFIG_ENV_MAX_ENTRIES
3252 Maximum number of entries in the hash table that is used
3253 internally to store the environment settings. The default
3254 setting is supposed to be generous and should work in most
3255 cases. This setting can be used to tune behaviour; see
3256 lib/hashtable.c for details.
3258 - CONFIG_ENV_FLAGS_LIST_DEFAULT
3259 - CONFIG_ENV_FLAGS_LIST_STATIC
3260 Enable validation of the values given to enviroment variables when
3261 calling env set. Variables can be restricted to only decimal,
3262 hexadecimal, or boolean. If CONFIG_CMD_NET is also defined,
3263 the variables can also be restricted to IP address or MAC address.
3265 The format of the list is:
3266 type_attribute = [s|d|x|b|i|m]
3267 access_atribute = [a|r|o|c]
3268 attributes = type_attribute[access_atribute]
3269 entry = variable_name[:attributes]
3272 The type attributes are:
3273 s - String (default)
3276 b - Boolean ([1yYtT|0nNfF])
3280 The access attributes are:
3286 - CONFIG_ENV_FLAGS_LIST_DEFAULT
3287 Define this to a list (string) to define the ".flags"
3288 envirnoment variable in the default or embedded environment.
3290 - CONFIG_ENV_FLAGS_LIST_STATIC
3291 Define this to a list (string) to define validation that
3292 should be done if an entry is not found in the ".flags"
3293 environment variable. To override a setting in the static
3294 list, simply add an entry for the same variable name to the
3297 - CONFIG_ENV_ACCESS_IGNORE_FORCE
3298 If defined, don't allow the -f switch to env set override variable
3301 - CONFIG_SYS_GENERIC_BOARD
3302 This selects the architecture-generic board system instead of the
3303 architecture-specific board files. It is intended to move boards
3304 to this new framework over time. Defining this will disable the
3305 arch/foo/lib/board.c file and use common/board_f.c and
3306 common/board_r.c instead. To use this option your architecture
3307 must support it (i.e. must define __HAVE_ARCH_GENERIC_BOARD in
3308 its config.mk file). If you find problems enabling this option on
3309 your board please report the problem and send patches!
3311 - CONFIG_SYS_SYM_OFFSETS
3312 This is set by architectures that use offsets for link symbols
3313 instead of absolute values. So bss_start is obtained using an
3314 offset _bss_start_ofs from CONFIG_SYS_TEXT_BASE, rather than
3315 directly. You should not need to touch this setting.
3318 The following definitions that deal with the placement and management
3319 of environment data (variable area); in general, we support the
3320 following configurations:
3322 - CONFIG_BUILD_ENVCRC:
3324 Builds up envcrc with the target environment so that external utils
3325 may easily extract it and embed it in final U-Boot images.
3327 - CONFIG_ENV_IS_IN_FLASH:
3329 Define this if the environment is in flash memory.
3331 a) The environment occupies one whole flash sector, which is
3332 "embedded" in the text segment with the U-Boot code. This
3333 happens usually with "bottom boot sector" or "top boot
3334 sector" type flash chips, which have several smaller
3335 sectors at the start or the end. For instance, such a
3336 layout can have sector sizes of 8, 2x4, 16, Nx32 kB. In
3337 such a case you would place the environment in one of the
3338 4 kB sectors - with U-Boot code before and after it. With
3339 "top boot sector" type flash chips, you would put the
3340 environment in one of the last sectors, leaving a gap
3341 between U-Boot and the environment.
3343 - CONFIG_ENV_OFFSET:
3345 Offset of environment data (variable area) to the
3346 beginning of flash memory; for instance, with bottom boot
3347 type flash chips the second sector can be used: the offset
3348 for this sector is given here.
3350 CONFIG_ENV_OFFSET is used relative to CONFIG_SYS_FLASH_BASE.
3354 This is just another way to specify the start address of
3355 the flash sector containing the environment (instead of
3358 - CONFIG_ENV_SECT_SIZE:
3360 Size of the sector containing the environment.
3363 b) Sometimes flash chips have few, equal sized, BIG sectors.
3364 In such a case you don't want to spend a whole sector for
3369 If you use this in combination with CONFIG_ENV_IS_IN_FLASH
3370 and CONFIG_ENV_SECT_SIZE, you can specify to use only a part
3371 of this flash sector for the environment. This saves
3372 memory for the RAM copy of the environment.
3374 It may also save flash memory if you decide to use this
3375 when your environment is "embedded" within U-Boot code,
3376 since then the remainder of the flash sector could be used
3377 for U-Boot code. It should be pointed out that this is
3378 STRONGLY DISCOURAGED from a robustness point of view:
3379 updating the environment in flash makes it always
3380 necessary to erase the WHOLE sector. If something goes
3381 wrong before the contents has been restored from a copy in
3382 RAM, your target system will be dead.
3384 - CONFIG_ENV_ADDR_REDUND
3385 CONFIG_ENV_SIZE_REDUND
3387 These settings describe a second storage area used to hold
3388 a redundant copy of the environment data, so that there is
3389 a valid backup copy in case there is a power failure during
3390 a "saveenv" operation.
3392 BE CAREFUL! Any changes to the flash layout, and some changes to the
3393 source code will make it necessary to adapt <board>/u-boot.lds*
3397 - CONFIG_ENV_IS_IN_NVRAM:
3399 Define this if you have some non-volatile memory device
3400 (NVRAM, battery buffered SRAM) which you want to use for the
3406 These two #defines are used to determine the memory area you
3407 want to use for environment. It is assumed that this memory
3408 can just be read and written to, without any special
3411 BE CAREFUL! The first access to the environment happens quite early
3412 in U-Boot initalization (when we try to get the setting of for the
3413 console baudrate). You *MUST* have mapped your NVRAM area then, or
3416 Please note that even with NVRAM we still use a copy of the
3417 environment in RAM: we could work on NVRAM directly, but we want to
3418 keep settings there always unmodified except somebody uses "saveenv"
3419 to save the current settings.
3422 - CONFIG_ENV_IS_IN_EEPROM:
3424 Use this if you have an EEPROM or similar serial access
3425 device and a driver for it.
3427 - CONFIG_ENV_OFFSET:
3430 These two #defines specify the offset and size of the
3431 environment area within the total memory of your EEPROM.
3433 - CONFIG_SYS_I2C_EEPROM_ADDR:
3434 If defined, specified the chip address of the EEPROM device.
3435 The default address is zero.
3437 - CONFIG_SYS_EEPROM_PAGE_WRITE_BITS:
3438 If defined, the number of bits used to address bytes in a
3439 single page in the EEPROM device. A 64 byte page, for example
3440 would require six bits.
3442 - CONFIG_SYS_EEPROM_PAGE_WRITE_DELAY_MS:
3443 If defined, the number of milliseconds to delay between
3444 page writes. The default is zero milliseconds.
3446 - CONFIG_SYS_I2C_EEPROM_ADDR_LEN:
3447 The length in bytes of the EEPROM memory array address. Note
3448 that this is NOT the chip address length!
3450 - CONFIG_SYS_I2C_EEPROM_ADDR_OVERFLOW:
3451 EEPROM chips that implement "address overflow" are ones
3452 like Catalyst 24WC04/08/16 which has 9/10/11 bits of
3453 address and the extra bits end up in the "chip address" bit
3454 slots. This makes a 24WC08 (1Kbyte) chip look like four 256
3457 Note that we consider the length of the address field to
3458 still be one byte because the extra address bits are hidden
3459 in the chip address.
3461 - CONFIG_SYS_EEPROM_SIZE:
3462 The size in bytes of the EEPROM device.
3464 - CONFIG_ENV_EEPROM_IS_ON_I2C
3465 define this, if you have I2C and SPI activated, and your
3466 EEPROM, which holds the environment, is on the I2C bus.
3468 - CONFIG_I2C_ENV_EEPROM_BUS
3469 if you have an Environment on an EEPROM reached over
3470 I2C muxes, you can define here, how to reach this
3471 EEPROM. For example:
3473 #define CONFIG_I2C_ENV_EEPROM_BUS "pca9547:70:d\0"
3475 EEPROM which holds the environment, is reached over
3476 a pca9547 i2c mux with address 0x70, channel 3.
3478 - CONFIG_ENV_IS_IN_DATAFLASH:
3480 Define this if you have a DataFlash memory device which you
3481 want to use for the environment.
3483 - CONFIG_ENV_OFFSET:
3487 These three #defines specify the offset and size of the
3488 environment area within the total memory of your DataFlash placed
3489 at the specified address.
3491 - CONFIG_ENV_IS_IN_REMOTE:
3493 Define this if you have a remote memory space which you
3494 want to use for the local device's environment.
3499 These two #defines specify the address and size of the
3500 environment area within the remote memory space. The
3501 local device can get the environment from remote memory
3502 space by SRIO or PCIE links.
3504 BE CAREFUL! For some special cases, the local device can not use
3505 "saveenv" command. For example, the local device will get the
3506 environment stored in a remote NOR flash by SRIO or PCIE link,
3507 but it can not erase, write this NOR flash by SRIO or PCIE interface.
3509 - CONFIG_ENV_IS_IN_NAND:
3511 Define this if you have a NAND device which you want to use
3512 for the environment.
3514 - CONFIG_ENV_OFFSET:
3517 These two #defines specify the offset and size of the environment
3518 area within the first NAND device. CONFIG_ENV_OFFSET must be
3519 aligned to an erase block boundary.
3521 - CONFIG_ENV_OFFSET_REDUND (optional):
3523 This setting describes a second storage area of CONFIG_ENV_SIZE
3524 size used to hold a redundant copy of the environment data, so
3525 that there is a valid backup copy in case there is a power failure
3526 during a "saveenv" operation. CONFIG_ENV_OFFSET_RENDUND must be
3527 aligned to an erase block boundary.
3529 - CONFIG_ENV_RANGE (optional):
3531 Specifies the length of the region in which the environment
3532 can be written. This should be a multiple of the NAND device's
3533 block size. Specifying a range with more erase blocks than
3534 are needed to hold CONFIG_ENV_SIZE allows bad blocks within
3535 the range to be avoided.
3537 - CONFIG_ENV_OFFSET_OOB (optional):
3539 Enables support for dynamically retrieving the offset of the
3540 environment from block zero's out-of-band data. The
3541 "nand env.oob" command can be used to record this offset.
3542 Currently, CONFIG_ENV_OFFSET_REDUND is not supported when
3543 using CONFIG_ENV_OFFSET_OOB.
3545 - CONFIG_NAND_ENV_DST
3547 Defines address in RAM to which the nand_spl code should copy the
3548 environment. If redundant environment is used, it will be copied to
3549 CONFIG_NAND_ENV_DST + CONFIG_ENV_SIZE.
3551 - CONFIG_ENV_IS_IN_UBI:
3553 Define this if you have an UBI volume that you want to use for the
3554 environment. This has the benefit of wear-leveling the environment
3555 accesses, which is important on NAND.
3557 - CONFIG_ENV_UBI_PART:
3559 Define this to a string that is the mtd partition containing the UBI.
3561 - CONFIG_ENV_UBI_VOLUME:
3563 Define this to the name of the volume that you want to store the
3566 - CONFIG_ENV_UBI_VOLUME_REDUND:
3568 Define this to the name of another volume to store a second copy of
3569 the environment in. This will enable redundant environments in UBI.
3570 It is assumed that both volumes are in the same MTD partition.
3572 - CONFIG_UBI_SILENCE_MSG
3573 - CONFIG_UBIFS_SILENCE_MSG
3575 You will probably want to define these to avoid a really noisy system
3576 when storing the env in UBI.
3578 - CONFIG_SYS_SPI_INIT_OFFSET
3580 Defines offset to the initial SPI buffer area in DPRAM. The
3581 area is used at an early stage (ROM part) if the environment
3582 is configured to reside in the SPI EEPROM: We need a 520 byte
3583 scratch DPRAM area. It is used between the two initialization
3584 calls (spi_init_f() and spi_init_r()). A value of 0xB00 seems
3585 to be a good choice since it makes it far enough from the
3586 start of the data area as well as from the stack pointer.
3588 Please note that the environment is read-only until the monitor
3589 has been relocated to RAM and a RAM copy of the environment has been
3590 created; also, when using EEPROM you will have to use getenv_f()
3591 until then to read environment variables.
3593 The environment is protected by a CRC32 checksum. Before the monitor
3594 is relocated into RAM, as a result of a bad CRC you will be working
3595 with the compiled-in default environment - *silently*!!! [This is
3596 necessary, because the first environment variable we need is the
3597 "baudrate" setting for the console - if we have a bad CRC, we don't
3598 have any device yet where we could complain.]
3600 Note: once the monitor has been relocated, then it will complain if
3601 the default environment is used; a new CRC is computed as soon as you
3602 use the "saveenv" command to store a valid environment.
3604 - CONFIG_SYS_FAULT_ECHO_LINK_DOWN:
3605 Echo the inverted Ethernet link state to the fault LED.
3607 Note: If this option is active, then CONFIG_SYS_FAULT_MII_ADDR
3608 also needs to be defined.
3610 - CONFIG_SYS_FAULT_MII_ADDR:
3611 MII address of the PHY to check for the Ethernet link state.
3613 - CONFIG_NS16550_MIN_FUNCTIONS:
3614 Define this if you desire to only have use of the NS16550_init
3615 and NS16550_putc functions for the serial driver located at
3616 drivers/serial/ns16550.c. This option is useful for saving
3617 space for already greatly restricted images, including but not
3618 limited to NAND_SPL configurations.
3620 - CONFIG_DISPLAY_BOARDINFO
3621 Display information about the board that U-Boot is running on
3622 when U-Boot starts up. The board function checkboard() is called
3625 - CONFIG_DISPLAY_BOARDINFO_LATE
3626 Similar to the previous option, but display this information
3627 later, once stdio is running and output goes to the LCD, if
3630 Low Level (hardware related) configuration options:
3631 ---------------------------------------------------
3633 - CONFIG_SYS_CACHELINE_SIZE:
3634 Cache Line Size of the CPU.
3636 - CONFIG_SYS_DEFAULT_IMMR:
3637 Default address of the IMMR after system reset.
3639 Needed on some 8260 systems (MPC8260ADS, PQ2FADS-ZU,
3640 and RPXsuper) to be able to adjust the position of
3641 the IMMR register after a reset.
3643 - CONFIG_SYS_CCSRBAR_DEFAULT:
3644 Default (power-on reset) physical address of CCSR on Freescale
3647 - CONFIG_SYS_CCSRBAR:
3648 Virtual address of CCSR. On a 32-bit build, this is typically
3649 the same value as CONFIG_SYS_CCSRBAR_DEFAULT.
3651 CONFIG_SYS_DEFAULT_IMMR must also be set to this value,
3652 for cross-platform code that uses that macro instead.
3654 - CONFIG_SYS_CCSRBAR_PHYS:
3655 Physical address of CCSR. CCSR can be relocated to a new
3656 physical address, if desired. In this case, this macro should
3657 be set to that address. Otherwise, it should be set to the
3658 same value as CONFIG_SYS_CCSRBAR_DEFAULT. For example, CCSR
3659 is typically relocated on 36-bit builds. It is recommended
3660 that this macro be defined via the _HIGH and _LOW macros:
3662 #define CONFIG_SYS_CCSRBAR_PHYS ((CONFIG_SYS_CCSRBAR_PHYS_HIGH
3663 * 1ull) << 32 | CONFIG_SYS_CCSRBAR_PHYS_LOW)
3665 - CONFIG_SYS_CCSRBAR_PHYS_HIGH:
3666 Bits 33-36 of CONFIG_SYS_CCSRBAR_PHYS. This value is typically
3667 either 0 (32-bit build) or 0xF (36-bit build). This macro is
3668 used in assembly code, so it must not contain typecasts or
3669 integer size suffixes (e.g. "ULL").
3671 - CONFIG_SYS_CCSRBAR_PHYS_LOW:
3672 Lower 32-bits of CONFIG_SYS_CCSRBAR_PHYS. This macro is
3673 used in assembly code, so it must not contain typecasts or
3674 integer size suffixes (e.g. "ULL").
3676 - CONFIG_SYS_CCSR_DO_NOT_RELOCATE:
3677 If this macro is defined, then CONFIG_SYS_CCSRBAR_PHYS will be
3678 forced to a value that ensures that CCSR is not relocated.
3680 - Floppy Disk Support:
3681 CONFIG_SYS_FDC_DRIVE_NUMBER
3683 the default drive number (default value 0)
3685 CONFIG_SYS_ISA_IO_STRIDE
3687 defines the spacing between FDC chipset registers
3690 CONFIG_SYS_ISA_IO_OFFSET
3692 defines the offset of register from address. It
3693 depends on which part of the data bus is connected to
3694 the FDC chipset. (default value 0)
3696 If CONFIG_SYS_ISA_IO_STRIDE CONFIG_SYS_ISA_IO_OFFSET and
3697 CONFIG_SYS_FDC_DRIVE_NUMBER are undefined, they take their
3700 if CONFIG_SYS_FDC_HW_INIT is defined, then the function
3701 fdc_hw_init() is called at the beginning of the FDC
3702 setup. fdc_hw_init() must be provided by the board
3703 source code. It is used to make hardware dependant
3707 Most IDE controllers were designed to be connected with PCI
3708 interface. Only few of them were designed for AHB interface.
3709 When software is doing ATA command and data transfer to
3710 IDE devices through IDE-AHB controller, some additional
3711 registers accessing to these kind of IDE-AHB controller
3714 - CONFIG_SYS_IMMR: Physical address of the Internal Memory.
3715 DO NOT CHANGE unless you know exactly what you're
3716 doing! (11-4) [MPC8xx/82xx systems only]
3718 - CONFIG_SYS_INIT_RAM_ADDR:
3720 Start address of memory area that can be used for
3721 initial data and stack; please note that this must be
3722 writable memory that is working WITHOUT special
3723 initialization, i. e. you CANNOT use normal RAM which
3724 will become available only after programming the
3725 memory controller and running certain initialization
3728 U-Boot uses the following memory types:
3729 - MPC8xx and MPC8260: IMMR (internal memory of the CPU)
3730 - MPC824X: data cache
3731 - PPC4xx: data cache
3733 - CONFIG_SYS_GBL_DATA_OFFSET:
3735 Offset of the initial data structure in the memory
3736 area defined by CONFIG_SYS_INIT_RAM_ADDR. Usually
3737 CONFIG_SYS_GBL_DATA_OFFSET is chosen such that the initial
3738 data is located at the end of the available space
3739 (sometimes written as (CONFIG_SYS_INIT_RAM_SIZE -
3740 CONFIG_SYS_INIT_DATA_SIZE), and the initial stack is just
3741 below that area (growing from (CONFIG_SYS_INIT_RAM_ADDR +
3742 CONFIG_SYS_GBL_DATA_OFFSET) downward.
3745 On the MPC824X (or other systems that use the data
3746 cache for initial memory) the address chosen for
3747 CONFIG_SYS_INIT_RAM_ADDR is basically arbitrary - it must
3748 point to an otherwise UNUSED address space between
3749 the top of RAM and the start of the PCI space.
3751 - CONFIG_SYS_SIUMCR: SIU Module Configuration (11-6)
3753 - CONFIG_SYS_SYPCR: System Protection Control (11-9)
3755 - CONFIG_SYS_TBSCR: Time Base Status and Control (11-26)
3757 - CONFIG_SYS_PISCR: Periodic Interrupt Status and Control (11-31)
3759 - CONFIG_SYS_PLPRCR: PLL, Low-Power, and Reset Control Register (15-30)
3761 - CONFIG_SYS_SCCR: System Clock and reset Control Register (15-27)
3763 - CONFIG_SYS_OR_TIMING_SDRAM:
3766 - CONFIG_SYS_MAMR_PTA:
3767 periodic timer for refresh
3769 - CONFIG_SYS_DER: Debug Event Register (37-47)
3771 - FLASH_BASE0_PRELIM, FLASH_BASE1_PRELIM, CONFIG_SYS_REMAP_OR_AM,
3772 CONFIG_SYS_PRELIM_OR_AM, CONFIG_SYS_OR_TIMING_FLASH, CONFIG_SYS_OR0_REMAP,
3773 CONFIG_SYS_OR0_PRELIM, CONFIG_SYS_BR0_PRELIM, CONFIG_SYS_OR1_REMAP, CONFIG_SYS_OR1_PRELIM,
3774 CONFIG_SYS_BR1_PRELIM:
3775 Memory Controller Definitions: BR0/1 and OR0/1 (FLASH)
3777 - SDRAM_BASE2_PRELIM, SDRAM_BASE3_PRELIM, SDRAM_MAX_SIZE,
3778 CONFIG_SYS_OR_TIMING_SDRAM, CONFIG_SYS_OR2_PRELIM, CONFIG_SYS_BR2_PRELIM,
3779 CONFIG_SYS_OR3_PRELIM, CONFIG_SYS_BR3_PRELIM:
3780 Memory Controller Definitions: BR2/3 and OR2/3 (SDRAM)
3782 - CONFIG_SYS_MAMR_PTA, CONFIG_SYS_MPTPR_2BK_4K, CONFIG_SYS_MPTPR_1BK_4K, CONFIG_SYS_MPTPR_2BK_8K,
3783 CONFIG_SYS_MPTPR_1BK_8K, CONFIG_SYS_MAMR_8COL, CONFIG_SYS_MAMR_9COL:
3784 Machine Mode Register and Memory Periodic Timer
3785 Prescaler definitions (SDRAM timing)
3787 - CONFIG_SYS_I2C_UCODE_PATCH, CONFIG_SYS_I2C_DPMEM_OFFSET [0x1FC0]:
3788 enable I2C microcode relocation patch (MPC8xx);
3789 define relocation offset in DPRAM [DSP2]
3791 - CONFIG_SYS_SMC_UCODE_PATCH, CONFIG_SYS_SMC_DPMEM_OFFSET [0x1FC0]:
3792 enable SMC microcode relocation patch (MPC8xx);
3793 define relocation offset in DPRAM [SMC1]
3795 - CONFIG_SYS_SPI_UCODE_PATCH, CONFIG_SYS_SPI_DPMEM_OFFSET [0x1FC0]:
3796 enable SPI microcode relocation patch (MPC8xx);
3797 define relocation offset in DPRAM [SCC4]
3799 - CONFIG_SYS_USE_OSCCLK:
3800 Use OSCM clock mode on MBX8xx board. Be careful,
3801 wrong setting might damage your board. Read
3802 doc/README.MBX before setting this variable!
3804 - CONFIG_SYS_CPM_POST_WORD_ADDR: (MPC8xx, MPC8260 only)
3805 Offset of the bootmode word in DPRAM used by post
3806 (Power On Self Tests). This definition overrides
3807 #define'd default value in commproc.h resp.
3810 - CONFIG_SYS_PCI_SLV_MEM_LOCAL, CONFIG_SYS_PCI_SLV_MEM_BUS, CONFIG_SYS_PICMR0_MASK_ATTRIB,
3811 CONFIG_SYS_PCI_MSTR0_LOCAL, CONFIG_SYS_PCIMSK0_MASK, CONFIG_SYS_PCI_MSTR1_LOCAL,
3812 CONFIG_SYS_PCIMSK1_MASK, CONFIG_SYS_PCI_MSTR_MEM_LOCAL, CONFIG_SYS_PCI_MSTR_MEM_BUS,
3813 CONFIG_SYS_CPU_PCI_MEM_START, CONFIG_SYS_PCI_MSTR_MEM_SIZE, CONFIG_SYS_POCMR0_MASK_ATTRIB,
3814 CONFIG_SYS_PCI_MSTR_MEMIO_LOCAL, CONFIG_SYS_PCI_MSTR_MEMIO_BUS, CPU_PCI_MEMIO_START,
3815 CONFIG_SYS_PCI_MSTR_MEMIO_SIZE, CONFIG_SYS_POCMR1_MASK_ATTRIB, CONFIG_SYS_PCI_MSTR_IO_LOCAL,
3816 CONFIG_SYS_PCI_MSTR_IO_BUS, CONFIG_SYS_CPU_PCI_IO_START, CONFIG_SYS_PCI_MSTR_IO_SIZE,
3817 CONFIG_SYS_POCMR2_MASK_ATTRIB: (MPC826x only)
3818 Overrides the default PCI memory map in arch/powerpc/cpu/mpc8260/pci.c if set.
3820 - CONFIG_PCI_DISABLE_PCIE:
3821 Disable PCI-Express on systems where it is supported but not
3824 - CONFIG_PCI_ENUM_ONLY
3825 Only scan through and get the devices on the busses.
3826 Don't do any setup work, presumably because someone or
3827 something has already done it, and we don't need to do it
3828 a second time. Useful for platforms that are pre-booted
3829 by coreboot or similar.
3832 Chip has SRIO or not
3835 Board has SRIO 1 port available
3838 Board has SRIO 2 port available
3840 - CONFIG_SYS_SRIOn_MEM_VIRT:
3841 Virtual Address of SRIO port 'n' memory region
3843 - CONFIG_SYS_SRIOn_MEM_PHYS:
3844 Physical Address of SRIO port 'n' memory region
3846 - CONFIG_SYS_SRIOn_MEM_SIZE:
3847 Size of SRIO port 'n' memory region
3849 - CONFIG_SYS_NDFC_16
3850 Defined to tell the NDFC that the NAND chip is using a
3853 - CONFIG_SYS_NDFC_EBC0_CFG
3854 Sets the EBC0_CFG register for the NDFC. If not defined
3855 a default value will be used.
3858 Get DDR timing information from an I2C EEPROM. Common
3859 with pluggable memory modules such as SODIMMs
3862 I2C address of the SPD EEPROM
3864 - CONFIG_SYS_SPD_BUS_NUM
3865 If SPD EEPROM is on an I2C bus other than the first
3866 one, specify here. Note that the value must resolve
3867 to something your driver can deal with.
3869 - CONFIG_SYS_DDR_RAW_TIMING
3870 Get DDR timing information from other than SPD. Common with
3871 soldered DDR chips onboard without SPD. DDR raw timing
3872 parameters are extracted from datasheet and hard-coded into
3873 header files or board specific files.
3875 - CONFIG_FSL_DDR_INTERACTIVE
3876 Enable interactive DDR debugging. See doc/README.fsl-ddr.
3878 - CONFIG_SYS_83XX_DDR_USES_CS0
3879 Only for 83xx systems. If specified, then DDR should
3880 be configured using CS0 and CS1 instead of CS2 and CS3.
3882 - CONFIG_ETHER_ON_FEC[12]
3883 Define to enable FEC[12] on a 8xx series processor.
3885 - CONFIG_FEC[12]_PHY
3886 Define to the hardcoded PHY address which corresponds
3887 to the given FEC; i. e.
3888 #define CONFIG_FEC1_PHY 4
3889 means that the PHY with address 4 is connected to FEC1
3891 When set to -1, means to probe for first available.
3893 - CONFIG_FEC[12]_PHY_NORXERR
3894 The PHY does not have a RXERR line (RMII only).
3895 (so program the FEC to ignore it).
3898 Enable RMII mode for all FECs.
3899 Note that this is a global option, we can't
3900 have one FEC in standard MII mode and another in RMII mode.
3902 - CONFIG_CRC32_VERIFY
3903 Add a verify option to the crc32 command.
3906 => crc32 -v <address> <count> <crc32>
3908 Where address/count indicate a memory area
3909 and crc32 is the correct crc32 which the
3913 Add the "loopw" memory command. This only takes effect if
3914 the memory commands are activated globally (CONFIG_CMD_MEM).
3917 Add the "mdc" and "mwc" memory commands. These are cyclic
3922 This command will print 4 bytes (10,11,12,13) each 500 ms.
3924 => mwc.l 100 12345678 10
3925 This command will write 12345678 to address 100 all 10 ms.
3927 This only takes effect if the memory commands are activated
3928 globally (CONFIG_CMD_MEM).
3930 - CONFIG_SKIP_LOWLEVEL_INIT
3931 [ARM, NDS32, MIPS only] If this variable is defined, then certain
3932 low level initializations (like setting up the memory
3933 controller) are omitted and/or U-Boot does not
3934 relocate itself into RAM.
3936 Normally this variable MUST NOT be defined. The only
3937 exception is when U-Boot is loaded (to RAM) by some
3938 other boot loader or by a debugger which performs
3939 these initializations itself.
3942 Modifies the behaviour of start.S when compiling a loader
3943 that is executed before the actual U-Boot. E.g. when
3944 compiling a NAND SPL.
3946 - CONFIG_ARCH_MAP_SYSMEM
3947 Generally U-Boot (and in particular the md command) uses
3948 effective address. It is therefore not necessary to regard
3949 U-Boot address as virtual addresses that need to be translated
3950 to physical addresses. However, sandbox requires this, since
3951 it maintains its own little RAM buffer which contains all
3952 addressable memory. This option causes some memory accesses
3953 to be mapped through map_sysmem() / unmap_sysmem().
3955 - CONFIG_USE_ARCH_MEMCPY
3956 CONFIG_USE_ARCH_MEMSET
3957 If these options are used a optimized version of memcpy/memset will
3958 be used if available. These functions may be faster under some
3959 conditions but may increase the binary size.
3961 - CONFIG_X86_RESET_VECTOR
3962 If defined, the x86 reset vector code is included. This is not
3963 needed when U-Boot is running from Coreboot.
3966 Defines the MPU clock speed (in MHz).
3968 NOTE : currently only supported on AM335x platforms.
3970 Freescale QE/FMAN Firmware Support:
3971 -----------------------------------
3973 The Freescale QUICCEngine (QE) and Frame Manager (FMAN) both support the
3974 loading of "firmware", which is encoded in the QE firmware binary format.
3975 This firmware often needs to be loaded during U-Boot booting, so macros
3976 are used to identify the storage device (NOR flash, SPI, etc) and the address
3979 - CONFIG_SYS_QE_FMAN_FW_ADDR
3980 The address in the storage device where the firmware is located. The
3981 meaning of this address depends on which CONFIG_SYS_QE_FW_IN_xxx macro
3984 - CONFIG_SYS_QE_FMAN_FW_LENGTH
3985 The maximum possible size of the firmware. The firmware binary format
3986 has a field that specifies the actual size of the firmware, but it
3987 might not be possible to read any part of the firmware unless some
3988 local storage is allocated to hold the entire firmware first.
3990 - CONFIG_SYS_QE_FMAN_FW_IN_NOR
3991 Specifies that QE/FMAN firmware is located in NOR flash, mapped as
3992 normal addressable memory via the LBC. CONFIG_SYS_FMAN_FW_ADDR is the
3993 virtual address in NOR flash.
3995 - CONFIG_SYS_QE_FMAN_FW_IN_NAND
3996 Specifies that QE/FMAN firmware is located in NAND flash.
3997 CONFIG_SYS_FMAN_FW_ADDR is the offset within NAND flash.
3999 - CONFIG_SYS_QE_FMAN_FW_IN_MMC
4000 Specifies that QE/FMAN firmware is located on the primary SD/MMC
4001 device. CONFIG_SYS_FMAN_FW_ADDR is the byte offset on that device.
4003 - CONFIG_SYS_QE_FMAN_FW_IN_SPIFLASH
4004 Specifies that QE/FMAN firmware is located on the primary SPI
4005 device. CONFIG_SYS_FMAN_FW_ADDR is the byte offset on that device.
4007 - CONFIG_SYS_QE_FMAN_FW_IN_REMOTE
4008 Specifies that QE/FMAN firmware is located in the remote (master)
4009 memory space. CONFIG_SYS_FMAN_FW_ADDR is a virtual address which
4010 can be mapped from slave TLB->slave LAW->slave SRIO or PCIE outbound
4011 window->master inbound window->master LAW->the ucode address in
4012 master's memory space.
4014 Building the Software:
4015 ======================
4017 Building U-Boot has been tested in several native build environments
4018 and in many different cross environments. Of course we cannot support
4019 all possibly existing versions of cross development tools in all
4020 (potentially obsolete) versions. In case of tool chain problems we
4021 recommend to use the ELDK (see http://www.denx.de/wiki/DULG/ELDK)
4022 which is extensively used to build and test U-Boot.
4024 If you are not using a native environment, it is assumed that you
4025 have GNU cross compiling tools available in your path. In this case,
4026 you must set the environment variable CROSS_COMPILE in your shell.
4027 Note that no changes to the Makefile or any other source files are
4028 necessary. For example using the ELDK on a 4xx CPU, please enter:
4030 $ CROSS_COMPILE=ppc_4xx-
4031 $ export CROSS_COMPILE
4033 Note: If you wish to generate Windows versions of the utilities in
4034 the tools directory you can use the MinGW toolchain
4035 (http://www.mingw.org). Set your HOST tools to the MinGW
4036 toolchain and execute 'make tools'. For example:
4038 $ make HOSTCC=i586-mingw32msvc-gcc HOSTSTRIP=i586-mingw32msvc-strip tools
4040 Binaries such as tools/mkimage.exe will be created which can
4041 be executed on computers running Windows.
4043 U-Boot is intended to be simple to build. After installing the
4044 sources you must configure U-Boot for one specific board type. This
4049 where "NAME_config" is the name of one of the existing configu-
4050 rations; see boards.cfg for supported names.
4052 Note: for some board special configuration names may exist; check if
4053 additional information is available from the board vendor; for
4054 instance, the TQM823L systems are available without (standard)
4055 or with LCD support. You can select such additional "features"
4056 when choosing the configuration, i. e.
4059 - will configure for a plain TQM823L, i. e. no LCD support
4061 make TQM823L_LCD_config
4062 - will configure for a TQM823L with U-Boot console on LCD
4067 Finally, type "make all", and you should get some working U-Boot
4068 images ready for download to / installation on your system:
4070 - "u-boot.bin" is a raw binary image
4071 - "u-boot" is an image in ELF binary format
4072 - "u-boot.srec" is in Motorola S-Record format
4074 By default the build is performed locally and the objects are saved
4075 in the source directory. One of the two methods can be used to change
4076 this behavior and build U-Boot to some external directory:
4078 1. Add O= to the make command line invocations:
4080 make O=/tmp/build distclean
4081 make O=/tmp/build NAME_config
4082 make O=/tmp/build all
4084 2. Set environment variable BUILD_DIR to point to the desired location:
4086 export BUILD_DIR=/tmp/build
4091 Note that the command line "O=" setting overrides the BUILD_DIR environment
4095 Please be aware that the Makefiles assume you are using GNU make, so
4096 for instance on NetBSD you might need to use "gmake" instead of
4100 If the system board that you have is not listed, then you will need
4101 to port U-Boot to your hardware platform. To do this, follow these
4104 1. Add a new configuration option for your board to the toplevel
4105 "boards.cfg" file, using the existing entries as examples.
4106 Follow the instructions there to keep the boards in order.
4107 2. Create a new directory to hold your board specific code. Add any
4108 files you need. In your board directory, you will need at least
4109 the "Makefile", a "<board>.c", "flash.c" and "u-boot.lds".
4110 3. Create a new configuration file "include/configs/<board>.h" for
4112 3. If you're porting U-Boot to a new CPU, then also create a new
4113 directory to hold your CPU specific code. Add any files you need.
4114 4. Run "make <board>_config" with your new name.
4115 5. Type "make", and you should get a working "u-boot.srec" file
4116 to be installed on your target system.
4117 6. Debug and solve any problems that might arise.
4118 [Of course, this last step is much harder than it sounds.]
4121 Testing of U-Boot Modifications, Ports to New Hardware, etc.:
4122 ==============================================================
4124 If you have modified U-Boot sources (for instance added a new board
4125 or support for new devices, a new CPU, etc.) you are expected to
4126 provide feedback to the other developers. The feedback normally takes
4127 the form of a "patch", i. e. a context diff against a certain (latest
4128 official or latest in the git repository) version of U-Boot sources.
4130 But before you submit such a patch, please verify that your modifi-
4131 cation did not break existing code. At least make sure that *ALL* of
4132 the supported boards compile WITHOUT ANY compiler warnings. To do so,
4133 just run the "MAKEALL" script, which will configure and build U-Boot
4134 for ALL supported system. Be warned, this will take a while. You can
4135 select which (cross) compiler to use by passing a `CROSS_COMPILE'
4136 environment variable to the script, i. e. to use the ELDK cross tools
4139 CROSS_COMPILE=ppc_8xx- MAKEALL
4141 or to build on a native PowerPC system you can type
4143 CROSS_COMPILE=' ' MAKEALL
4145 When using the MAKEALL script, the default behaviour is to build
4146 U-Boot in the source directory. This location can be changed by
4147 setting the BUILD_DIR environment variable. Also, for each target
4148 built, the MAKEALL script saves two log files (<target>.ERR and
4149 <target>.MAKEALL) in the <source dir>/LOG directory. This default
4150 location can be changed by setting the MAKEALL_LOGDIR environment
4151 variable. For example:
4153 export BUILD_DIR=/tmp/build
4154 export MAKEALL_LOGDIR=/tmp/log
4155 CROSS_COMPILE=ppc_8xx- MAKEALL
4157 With the above settings build objects are saved in the /tmp/build,
4158 log files are saved in the /tmp/log and the source tree remains clean
4159 during the whole build process.
4162 See also "U-Boot Porting Guide" below.
4165 Monitor Commands - Overview:
4166 ============================
4168 go - start application at address 'addr'
4169 run - run commands in an environment variable
4170 bootm - boot application image from memory
4171 bootp - boot image via network using BootP/TFTP protocol
4172 bootz - boot zImage from memory
4173 tftpboot- boot image via network using TFTP protocol
4174 and env variables "ipaddr" and "serverip"
4175 (and eventually "gatewayip")
4176 tftpput - upload a file via network using TFTP protocol
4177 rarpboot- boot image via network using RARP/TFTP protocol
4178 diskboot- boot from IDE devicebootd - boot default, i.e., run 'bootcmd'
4179 loads - load S-Record file over serial line
4180 loadb - load binary file over serial line (kermit mode)
4182 mm - memory modify (auto-incrementing)
4183 nm - memory modify (constant address)
4184 mw - memory write (fill)
4186 cmp - memory compare
4187 crc32 - checksum calculation
4188 i2c - I2C sub-system
4189 sspi - SPI utility commands
4190 base - print or set address offset
4191 printenv- print environment variables
4192 setenv - set environment variables
4193 saveenv - save environment variables to persistent storage
4194 protect - enable or disable FLASH write protection
4195 erase - erase FLASH memory
4196 flinfo - print FLASH memory information
4197 nand - NAND memory operations (see doc/README.nand)
4198 bdinfo - print Board Info structure
4199 iminfo - print header information for application image
4200 coninfo - print console devices and informations
4201 ide - IDE sub-system
4202 loop - infinite loop on address range
4203 loopw - infinite write loop on address range
4204 mtest - simple RAM test
4205 icache - enable or disable instruction cache
4206 dcache - enable or disable data cache
4207 reset - Perform RESET of the CPU
4208 echo - echo args to console
4209 version - print monitor version
4210 help - print online help
4211 ? - alias for 'help'
4214 Monitor Commands - Detailed Description:
4215 ========================================
4219 For now: just type "help <command>".
4222 Environment Variables:
4223 ======================
4225 U-Boot supports user configuration using Environment Variables which
4226 can be made persistent by saving to Flash memory.
4228 Environment Variables are set using "setenv", printed using
4229 "printenv", and saved to Flash using "saveenv". Using "setenv"
4230 without a value can be used to delete a variable from the
4231 environment. As long as you don't save the environment you are
4232 working with an in-memory copy. In case the Flash area containing the
4233 environment is erased by accident, a default environment is provided.
4235 Some configuration options can be set using Environment Variables.
4237 List of environment variables (most likely not complete):
4239 baudrate - see CONFIG_BAUDRATE
4241 bootdelay - see CONFIG_BOOTDELAY
4243 bootcmd - see CONFIG_BOOTCOMMAND
4245 bootargs - Boot arguments when booting an RTOS image
4247 bootfile - Name of the image to load with TFTP
4249 bootm_low - Memory range available for image processing in the bootm
4250 command can be restricted. This variable is given as
4251 a hexadecimal number and defines lowest address allowed
4252 for use by the bootm command. See also "bootm_size"
4253 environment variable. Address defined by "bootm_low" is
4254 also the base of the initial memory mapping for the Linux
4255 kernel -- see the description of CONFIG_SYS_BOOTMAPSZ and
4258 bootm_mapsize - Size of the initial memory mapping for the Linux kernel.
4259 This variable is given as a hexadecimal number and it
4260 defines the size of the memory region starting at base
4261 address bootm_low that is accessible by the Linux kernel
4262 during early boot. If unset, CONFIG_SYS_BOOTMAPSZ is used
4263 as the default value if it is defined, and bootm_size is
4266 bootm_size - Memory range available for image processing in the bootm
4267 command can be restricted. This variable is given as
4268 a hexadecimal number and defines the size of the region
4269 allowed for use by the bootm command. See also "bootm_low"
4270 environment variable.
4272 updatefile - Location of the software update file on a TFTP server, used
4273 by the automatic software update feature. Please refer to
4274 documentation in doc/README.update for more details.
4276 autoload - if set to "no" (any string beginning with 'n'),
4277 "bootp" will just load perform a lookup of the
4278 configuration from the BOOTP server, but not try to
4279 load any image using TFTP
4281 autostart - if set to "yes", an image loaded using the "bootp",
4282 "rarpboot", "tftpboot" or "diskboot" commands will
4283 be automatically started (by internally calling
4286 If set to "no", a standalone image passed to the
4287 "bootm" command will be copied to the load address
4288 (and eventually uncompressed), but NOT be started.
4289 This can be used to load and uncompress arbitrary
4292 fdt_high - if set this restricts the maximum address that the
4293 flattened device tree will be copied into upon boot.
4294 For example, if you have a system with 1 GB memory
4295 at physical address 0x10000000, while Linux kernel
4296 only recognizes the first 704 MB as low memory, you
4297 may need to set fdt_high as 0x3C000000 to have the
4298 device tree blob be copied to the maximum address
4299 of the 704 MB low memory, so that Linux kernel can
4300 access it during the boot procedure.
4302 If this is set to the special value 0xFFFFFFFF then
4303 the fdt will not be copied at all on boot. For this
4304 to work it must reside in writable memory, have
4305 sufficient padding on the end of it for u-boot to
4306 add the information it needs into it, and the memory
4307 must be accessible by the kernel.
4309 fdtcontroladdr- if set this is the address of the control flattened
4310 device tree used by U-Boot when CONFIG_OF_CONTROL is
4313 i2cfast - (PPC405GP|PPC405EP only)
4314 if set to 'y' configures Linux I2C driver for fast
4315 mode (400kHZ). This environment variable is used in
4316 initialization code. So, for changes to be effective
4317 it must be saved and board must be reset.
4319 initrd_high - restrict positioning of initrd images:
4320 If this variable is not set, initrd images will be
4321 copied to the highest possible address in RAM; this
4322 is usually what you want since it allows for
4323 maximum initrd size. If for some reason you want to
4324 make sure that the initrd image is loaded below the
4325 CONFIG_SYS_BOOTMAPSZ limit, you can set this environment
4326 variable to a value of "no" or "off" or "0".
4327 Alternatively, you can set it to a maximum upper
4328 address to use (U-Boot will still check that it
4329 does not overwrite the U-Boot stack and data).
4331 For instance, when you have a system with 16 MB
4332 RAM, and want to reserve 4 MB from use by Linux,
4333 you can do this by adding "mem=12M" to the value of
4334 the "bootargs" variable. However, now you must make
4335 sure that the initrd image is placed in the first
4336 12 MB as well - this can be done with
4338 setenv initrd_high 00c00000
4340 If you set initrd_high to 0xFFFFFFFF, this is an
4341 indication to U-Boot that all addresses are legal
4342 for the Linux kernel, including addresses in flash
4343 memory. In this case U-Boot will NOT COPY the
4344 ramdisk at all. This may be useful to reduce the
4345 boot time on your system, but requires that this
4346 feature is supported by your Linux kernel.
4348 ipaddr - IP address; needed for tftpboot command
4350 loadaddr - Default load address for commands like "bootp",
4351 "rarpboot", "tftpboot", "loadb" or "diskboot"
4353 loads_echo - see CONFIG_LOADS_ECHO
4355 serverip - TFTP server IP address; needed for tftpboot command
4357 bootretry - see CONFIG_BOOT_RETRY_TIME
4359 bootdelaykey - see CONFIG_AUTOBOOT_DELAY_STR
4361 bootstopkey - see CONFIG_AUTOBOOT_STOP_STR
4363 ethprime - controls which interface is used first.
4365 ethact - controls which interface is currently active.
4366 For example you can do the following
4368 => setenv ethact FEC
4369 => ping 192.168.0.1 # traffic sent on FEC
4370 => setenv ethact SCC
4371 => ping 10.0.0.1 # traffic sent on SCC
4373 ethrotate - When set to "no" U-Boot does not go through all
4374 available network interfaces.
4375 It just stays at the currently selected interface.
4377 netretry - When set to "no" each network operation will
4378 either succeed or fail without retrying.
4379 When set to "once" the network operation will
4380 fail when all the available network interfaces
4381 are tried once without success.
4382 Useful on scripts which control the retry operation
4385 npe_ucode - set load address for the NPE microcode
4387 tftpsrcport - If this is set, the value is used for TFTP's
4390 tftpdstport - If this is set, the value is used for TFTP's UDP
4391 destination port instead of the Well Know Port 69.
4393 tftpblocksize - Block size to use for TFTP transfers; if not set,
4394 we use the TFTP server's default block size
4396 tftptimeout - Retransmission timeout for TFTP packets (in milli-
4397 seconds, minimum value is 1000 = 1 second). Defines
4398 when a packet is considered to be lost so it has to
4399 be retransmitted. The default is 5000 = 5 seconds.
4400 Lowering this value may make downloads succeed
4401 faster in networks with high packet loss rates or
4402 with unreliable TFTP servers.
4404 vlan - When set to a value < 4095 the traffic over
4405 Ethernet is encapsulated/received over 802.1q
4408 The following image location variables contain the location of images
4409 used in booting. The "Image" column gives the role of the image and is
4410 not an environment variable name. The other columns are environment
4411 variable names. "File Name" gives the name of the file on a TFTP
4412 server, "RAM Address" gives the location in RAM the image will be
4413 loaded to, and "Flash Location" gives the image's address in NOR
4414 flash or offset in NAND flash.
4416 *Note* - these variables don't have to be defined for all boards, some
4417 boards currenlty use other variables for these purposes, and some
4418 boards use these variables for other purposes.
4420 Image File Name RAM Address Flash Location
4421 ----- --------- ----------- --------------
4422 u-boot u-boot u-boot_addr_r u-boot_addr
4423 Linux kernel bootfile kernel_addr_r kernel_addr
4424 device tree blob fdtfile fdt_addr_r fdt_addr
4425 ramdisk ramdiskfile ramdisk_addr_r ramdisk_addr
4427 The following environment variables may be used and automatically
4428 updated by the network boot commands ("bootp" and "rarpboot"),
4429 depending the information provided by your boot server:
4431 bootfile - see above
4432 dnsip - IP address of your Domain Name Server
4433 dnsip2 - IP address of your secondary Domain Name Server
4434 gatewayip - IP address of the Gateway (Router) to use
4435 hostname - Target hostname
4437 netmask - Subnet Mask
4438 rootpath - Pathname of the root filesystem on the NFS server
4439 serverip - see above
4442 There are two special Environment Variables:
4444 serial# - contains hardware identification information such
4445 as type string and/or serial number
4446 ethaddr - Ethernet address
4448 These variables can be set only once (usually during manufacturing of
4449 the board). U-Boot refuses to delete or overwrite these variables
4450 once they have been set once.
4453 Further special Environment Variables:
4455 ver - Contains the U-Boot version string as printed
4456 with the "version" command. This variable is
4457 readonly (see CONFIG_VERSION_VARIABLE).
4460 Please note that changes to some configuration parameters may take
4461 only effect after the next boot (yes, that's just like Windoze :-).
4464 Callback functions for environment variables:
4465 ---------------------------------------------
4467 For some environment variables, the behavior of u-boot needs to change
4468 when their values are changed. This functionailty allows functions to
4469 be associated with arbitrary variables. On creation, overwrite, or
4470 deletion, the callback will provide the opportunity for some side
4471 effect to happen or for the change to be rejected.
4473 The callbacks are named and associated with a function using the
4474 U_BOOT_ENV_CALLBACK macro in your board or driver code.
4476 These callbacks are associated with variables in one of two ways. The
4477 static list can be added to by defining CONFIG_ENV_CALLBACK_LIST_STATIC
4478 in the board configuration to a string that defines a list of
4479 associations. The list must be in the following format:
4481 entry = variable_name[:callback_name]
4484 If the callback name is not specified, then the callback is deleted.
4485 Spaces are also allowed anywhere in the list.
4487 Callbacks can also be associated by defining the ".callbacks" variable
4488 with the same list format above. Any association in ".callbacks" will
4489 override any association in the static list. You can define
4490 CONFIG_ENV_CALLBACK_LIST_DEFAULT to a list (string) to define the
4491 ".callbacks" envirnoment variable in the default or embedded environment.
4494 Command Line Parsing:
4495 =====================
4497 There are two different command line parsers available with U-Boot:
4498 the old "simple" one, and the much more powerful "hush" shell:
4500 Old, simple command line parser:
4501 --------------------------------
4503 - supports environment variables (through setenv / saveenv commands)
4504 - several commands on one line, separated by ';'
4505 - variable substitution using "... ${name} ..." syntax
4506 - special characters ('$', ';') can be escaped by prefixing with '\',
4508 setenv bootcmd bootm \${address}
4509 - You can also escape text by enclosing in single apostrophes, for example:
4510 setenv addip 'setenv bootargs $bootargs ip=$ipaddr:$serverip:$gatewayip:$netmask:$hostname::off'
4515 - similar to Bourne shell, with control structures like
4516 if...then...else...fi, for...do...done; while...do...done,
4517 until...do...done, ...
4518 - supports environment ("global") variables (through setenv / saveenv
4519 commands) and local shell variables (through standard shell syntax
4520 "name=value"); only environment variables can be used with "run"
4526 (1) If a command line (or an environment variable executed by a "run"
4527 command) contains several commands separated by semicolon, and
4528 one of these commands fails, then the remaining commands will be
4531 (2) If you execute several variables with one call to run (i. e.
4532 calling run with a list of variables as arguments), any failing
4533 command will cause "run" to terminate, i. e. the remaining
4534 variables are not executed.
4536 Note for Redundant Ethernet Interfaces:
4537 =======================================
4539 Some boards come with redundant Ethernet interfaces; U-Boot supports
4540 such configurations and is capable of automatic selection of a
4541 "working" interface when needed. MAC assignment works as follows:
4543 Network interfaces are numbered eth0, eth1, eth2, ... Corresponding
4544 MAC addresses can be stored in the environment as "ethaddr" (=>eth0),
4545 "eth1addr" (=>eth1), "eth2addr", ...
4547 If the network interface stores some valid MAC address (for instance
4548 in SROM), this is used as default address if there is NO correspon-
4549 ding setting in the environment; if the corresponding environment
4550 variable is set, this overrides the settings in the card; that means:
4552 o If the SROM has a valid MAC address, and there is no address in the
4553 environment, the SROM's address is used.
4555 o If there is no valid address in the SROM, and a definition in the
4556 environment exists, then the value from the environment variable is
4559 o If both the SROM and the environment contain a MAC address, and
4560 both addresses are the same, this MAC address is used.
4562 o If both the SROM and the environment contain a MAC address, and the
4563 addresses differ, the value from the environment is used and a
4566 o If neither SROM nor the environment contain a MAC address, an error
4569 If Ethernet drivers implement the 'write_hwaddr' function, valid MAC addresses
4570 will be programmed into hardware as part of the initialization process. This
4571 may be skipped by setting the appropriate 'ethmacskip' environment variable.
4572 The naming convention is as follows:
4573 "ethmacskip" (=>eth0), "eth1macskip" (=>eth1) etc.
4578 U-Boot is capable of booting (and performing other auxiliary operations on)
4579 images in two formats:
4581 New uImage format (FIT)
4582 -----------------------
4584 Flexible and powerful format based on Flattened Image Tree -- FIT (similar
4585 to Flattened Device Tree). It allows the use of images with multiple
4586 components (several kernels, ramdisks, etc.), with contents protected by
4587 SHA1, MD5 or CRC32. More details are found in the doc/uImage.FIT directory.
4593 Old image format is based on binary files which can be basically anything,
4594 preceded by a special header; see the definitions in include/image.h for
4595 details; basically, the header defines the following image properties:
4597 * Target Operating System (Provisions for OpenBSD, NetBSD, FreeBSD,
4598 4.4BSD, Linux, SVR4, Esix, Solaris, Irix, SCO, Dell, NCR, VxWorks,
4599 LynxOS, pSOS, QNX, RTEMS, INTEGRITY;
4600 Currently supported: Linux, NetBSD, VxWorks, QNX, RTEMS, LynxOS,
4602 * Target CPU Architecture (Provisions for Alpha, ARM, AVR32, Intel x86,
4603 IA64, MIPS, NDS32, Nios II, PowerPC, IBM S390, SuperH, Sparc, Sparc 64 Bit;
4604 Currently supported: ARM, AVR32, Intel x86, MIPS, NDS32, Nios II, PowerPC).
4605 * Compression Type (uncompressed, gzip, bzip2)
4611 The header is marked by a special Magic Number, and both the header
4612 and the data portions of the image are secured against corruption by
4619 Although U-Boot should support any OS or standalone application
4620 easily, the main focus has always been on Linux during the design of
4623 U-Boot includes many features that so far have been part of some
4624 special "boot loader" code within the Linux kernel. Also, any
4625 "initrd" images to be used are no longer part of one big Linux image;
4626 instead, kernel and "initrd" are separate images. This implementation
4627 serves several purposes:
4629 - the same features can be used for other OS or standalone
4630 applications (for instance: using compressed images to reduce the
4631 Flash memory footprint)
4633 - it becomes much easier to port new Linux kernel versions because
4634 lots of low-level, hardware dependent stuff are done by U-Boot
4636 - the same Linux kernel image can now be used with different "initrd"
4637 images; of course this also means that different kernel images can
4638 be run with the same "initrd". This makes testing easier (you don't
4639 have to build a new "zImage.initrd" Linux image when you just
4640 change a file in your "initrd"). Also, a field-upgrade of the
4641 software is easier now.
4647 Porting Linux to U-Boot based systems:
4648 ---------------------------------------
4650 U-Boot cannot save you from doing all the necessary modifications to
4651 configure the Linux device drivers for use with your target hardware
4652 (no, we don't intend to provide a full virtual machine interface to
4655 But now you can ignore ALL boot loader code (in arch/powerpc/mbxboot).
4657 Just make sure your machine specific header file (for instance
4658 include/asm-ppc/tqm8xx.h) includes the same definition of the Board
4659 Information structure as we define in include/asm-<arch>/u-boot.h,
4660 and make sure that your definition of IMAP_ADDR uses the same value
4661 as your U-Boot configuration in CONFIG_SYS_IMMR.
4664 Configuring the Linux kernel:
4665 -----------------------------
4667 No specific requirements for U-Boot. Make sure you have some root
4668 device (initial ramdisk, NFS) for your target system.
4671 Building a Linux Image:
4672 -----------------------
4674 With U-Boot, "normal" build targets like "zImage" or "bzImage" are
4675 not used. If you use recent kernel source, a new build target
4676 "uImage" will exist which automatically builds an image usable by
4677 U-Boot. Most older kernels also have support for a "pImage" target,
4678 which was introduced for our predecessor project PPCBoot and uses a
4679 100% compatible format.
4688 The "uImage" build target uses a special tool (in 'tools/mkimage') to
4689 encapsulate a compressed Linux kernel image with header information,
4690 CRC32 checksum etc. for use with U-Boot. This is what we are doing:
4692 * build a standard "vmlinux" kernel image (in ELF binary format):
4694 * convert the kernel into a raw binary image:
4696 ${CROSS_COMPILE}-objcopy -O binary \
4697 -R .note -R .comment \
4698 -S vmlinux linux.bin
4700 * compress the binary image:
4704 * package compressed binary image for U-Boot:
4706 mkimage -A ppc -O linux -T kernel -C gzip \
4707 -a 0 -e 0 -n "Linux Kernel Image" \
4708 -d linux.bin.gz uImage
4711 The "mkimage" tool can also be used to create ramdisk images for use
4712 with U-Boot, either separated from the Linux kernel image, or
4713 combined into one file. "mkimage" encapsulates the images with a 64
4714 byte header containing information about target architecture,
4715 operating system, image type, compression method, entry points, time
4716 stamp, CRC32 checksums, etc.
4718 "mkimage" can be called in two ways: to verify existing images and
4719 print the header information, or to build new images.
4721 In the first form (with "-l" option) mkimage lists the information
4722 contained in the header of an existing U-Boot image; this includes
4723 checksum verification:
4725 tools/mkimage -l image
4726 -l ==> list image header information
4728 The second form (with "-d" option) is used to build a U-Boot image
4729 from a "data file" which is used as image payload:
4731 tools/mkimage -A arch -O os -T type -C comp -a addr -e ep \
4732 -n name -d data_file image
4733 -A ==> set architecture to 'arch'
4734 -O ==> set operating system to 'os'
4735 -T ==> set image type to 'type'
4736 -C ==> set compression type 'comp'
4737 -a ==> set load address to 'addr' (hex)
4738 -e ==> set entry point to 'ep' (hex)
4739 -n ==> set image name to 'name'
4740 -d ==> use image data from 'datafile'
4742 Right now, all Linux kernels for PowerPC systems use the same load
4743 address (0x00000000), but the entry point address depends on the
4746 - 2.2.x kernels have the entry point at 0x0000000C,
4747 - 2.3.x and later kernels have the entry point at 0x00000000.
4749 So a typical call to build a U-Boot image would read:
4751 -> tools/mkimage -n '2.4.4 kernel for TQM850L' \
4752 > -A ppc -O linux -T kernel -C gzip -a 0 -e 0 \
4753 > -d /opt/elsk/ppc_8xx/usr/src/linux-2.4.4/arch/powerpc/coffboot/vmlinux.gz \
4754 > examples/uImage.TQM850L
4755 Image Name: 2.4.4 kernel for TQM850L
4756 Created: Wed Jul 19 02:34:59 2000
4757 Image Type: PowerPC Linux Kernel Image (gzip compressed)
4758 Data Size: 335725 Bytes = 327.86 kB = 0.32 MB
4759 Load Address: 0x00000000
4760 Entry Point: 0x00000000
4762 To verify the contents of the image (or check for corruption):
4764 -> tools/mkimage -l examples/uImage.TQM850L
4765 Image Name: 2.4.4 kernel for TQM850L
4766 Created: Wed Jul 19 02:34:59 2000
4767 Image Type: PowerPC Linux Kernel Image (gzip compressed)
4768 Data Size: 335725 Bytes = 327.86 kB = 0.32 MB
4769 Load Address: 0x00000000
4770 Entry Point: 0x00000000
4772 NOTE: for embedded systems where boot time is critical you can trade
4773 speed for memory and install an UNCOMPRESSED image instead: this
4774 needs more space in Flash, but boots much faster since it does not
4775 need to be uncompressed:
4777 -> gunzip /opt/elsk/ppc_8xx/usr/src/linux-2.4.4/arch/powerpc/coffboot/vmlinux.gz
4778 -> tools/mkimage -n '2.4.4 kernel for TQM850L' \
4779 > -A ppc -O linux -T kernel -C none -a 0 -e 0 \
4780 > -d /opt/elsk/ppc_8xx/usr/src/linux-2.4.4/arch/powerpc/coffboot/vmlinux \
4781 > examples/uImage.TQM850L-uncompressed
4782 Image Name: 2.4.4 kernel for TQM850L
4783 Created: Wed Jul 19 02:34:59 2000
4784 Image Type: PowerPC Linux Kernel Image (uncompressed)
4785 Data Size: 792160 Bytes = 773.59 kB = 0.76 MB
4786 Load Address: 0x00000000
4787 Entry Point: 0x00000000
4790 Similar you can build U-Boot images from a 'ramdisk.image.gz' file
4791 when your kernel is intended to use an initial ramdisk:
4793 -> tools/mkimage -n 'Simple Ramdisk Image' \
4794 > -A ppc -O linux -T ramdisk -C gzip \
4795 > -d /LinuxPPC/images/SIMPLE-ramdisk.image.gz examples/simple-initrd
4796 Image Name: Simple Ramdisk Image
4797 Created: Wed Jan 12 14:01:50 2000
4798 Image Type: PowerPC Linux RAMDisk Image (gzip compressed)
4799 Data Size: 566530 Bytes = 553.25 kB = 0.54 MB
4800 Load Address: 0x00000000
4801 Entry Point: 0x00000000
4804 Installing a Linux Image:
4805 -------------------------
4807 To downloading a U-Boot image over the serial (console) interface,
4808 you must convert the image to S-Record format:
4810 objcopy -I binary -O srec examples/image examples/image.srec
4812 The 'objcopy' does not understand the information in the U-Boot
4813 image header, so the resulting S-Record file will be relative to
4814 address 0x00000000. To load it to a given address, you need to
4815 specify the target address as 'offset' parameter with the 'loads'
4818 Example: install the image to address 0x40100000 (which on the
4819 TQM8xxL is in the first Flash bank):
4821 => erase 40100000 401FFFFF
4827 ## Ready for S-Record download ...
4828 ~>examples/image.srec
4829 1 2 3 4 5 6 7 8 9 10 11 12 13 ...
4831 15989 15990 15991 15992
4832 [file transfer complete]
4834 ## Start Addr = 0x00000000
4837 You can check the success of the download using the 'iminfo' command;
4838 this includes a checksum verification so you can be sure no data
4839 corruption happened:
4843 ## Checking Image at 40100000 ...
4844 Image Name: 2.2.13 for initrd on TQM850L
4845 Image Type: PowerPC Linux Kernel Image (gzip compressed)
4846 Data Size: 335725 Bytes = 327 kB = 0 MB
4847 Load Address: 00000000
4848 Entry Point: 0000000c
4849 Verifying Checksum ... OK
4855 The "bootm" command is used to boot an application that is stored in
4856 memory (RAM or Flash). In case of a Linux kernel image, the contents
4857 of the "bootargs" environment variable is passed to the kernel as
4858 parameters. You can check and modify this variable using the
4859 "printenv" and "setenv" commands:
4862 => printenv bootargs
4863 bootargs=root=/dev/ram
4865 => setenv bootargs root=/dev/nfs rw nfsroot=10.0.0.2:/LinuxPPC nfsaddrs=10.0.0.99:10.0.0.2
4867 => printenv bootargs
4868 bootargs=root=/dev/nfs rw nfsroot=10.0.0.2:/LinuxPPC nfsaddrs=10.0.0.99:10.0.0.2
4871 ## Booting Linux kernel at 40020000 ...
4872 Image Name: 2.2.13 for NFS on TQM850L
4873 Image Type: PowerPC Linux Kernel Image (gzip compressed)
4874 Data Size: 381681 Bytes = 372 kB = 0 MB
4875 Load Address: 00000000
4876 Entry Point: 0000000c
4877 Verifying Checksum ... OK
4878 Uncompressing Kernel Image ... OK
4879 Linux version 2.2.13 (wd@denx.local.net) (gcc version 2.95.2 19991024 (release)) #1 Wed Jul 19 02:35:17 MEST 2000
4880 Boot arguments: root=/dev/nfs rw nfsroot=10.0.0.2:/LinuxPPC nfsaddrs=10.0.0.99:10.0.0.2
4881 time_init: decrementer frequency = 187500000/60
4882 Calibrating delay loop... 49.77 BogoMIPS
4883 Memory: 15208k available (700k kernel code, 444k data, 32k init) [c0000000,c1000000]
4886 If you want to boot a Linux kernel with initial RAM disk, you pass
4887 the memory addresses of both the kernel and the initrd image (PPBCOOT
4888 format!) to the "bootm" command:
4890 => imi 40100000 40200000
4892 ## Checking Image at 40100000 ...
4893 Image Name: 2.2.13 for initrd on TQM850L
4894 Image Type: PowerPC Linux Kernel Image (gzip compressed)
4895 Data Size: 335725 Bytes = 327 kB = 0 MB
4896 Load Address: 00000000
4897 Entry Point: 0000000c
4898 Verifying Checksum ... OK
4900 ## Checking Image at 40200000 ...
4901 Image Name: Simple Ramdisk Image
4902 Image Type: PowerPC Linux RAMDisk Image (gzip compressed)
4903 Data Size: 566530 Bytes = 553 kB = 0 MB
4904 Load Address: 00000000
4905 Entry Point: 00000000
4906 Verifying Checksum ... OK
4908 => bootm 40100000 40200000
4909 ## Booting Linux kernel at 40100000 ...
4910 Image Name: 2.2.13 for initrd on TQM850L
4911 Image Type: PowerPC Linux Kernel Image (gzip compressed)
4912 Data Size: 335725 Bytes = 327 kB = 0 MB
4913 Load Address: 00000000
4914 Entry Point: 0000000c
4915 Verifying Checksum ... OK
4916 Uncompressing Kernel Image ... OK
4917 ## Loading RAMDisk Image at 40200000 ...
4918 Image Name: Simple Ramdisk Image
4919 Image Type: PowerPC Linux RAMDisk Image (gzip compressed)
4920 Data Size: 566530 Bytes = 553 kB = 0 MB
4921 Load Address: 00000000
4922 Entry Point: 00000000
4923 Verifying Checksum ... OK
4924 Loading Ramdisk ... OK
4925 Linux version 2.2.13 (wd@denx.local.net) (gcc version 2.95.2 19991024 (release)) #1 Wed Jul 19 02:32:08 MEST 2000
4926 Boot arguments: root=/dev/ram
4927 time_init: decrementer frequency = 187500000/60
4928 Calibrating delay loop... 49.77 BogoMIPS
4930 RAMDISK: Compressed image found at block 0
4931 VFS: Mounted root (ext2 filesystem).
4935 Boot Linux and pass a flat device tree:
4938 First, U-Boot must be compiled with the appropriate defines. See the section
4939 titled "Linux Kernel Interface" above for a more in depth explanation. The
4940 following is an example of how to start a kernel and pass an updated
4946 oft=oftrees/mpc8540ads.dtb
4947 => tftp $oftaddr $oft
4948 Speed: 1000, full duplex
4950 TFTP from server 192.168.1.1; our IP address is 192.168.1.101
4951 Filename 'oftrees/mpc8540ads.dtb'.
4952 Load address: 0x300000
4955 Bytes transferred = 4106 (100a hex)
4956 => tftp $loadaddr $bootfile
4957 Speed: 1000, full duplex
4959 TFTP from server 192.168.1.1; our IP address is 192.168.1.2
4961 Load address: 0x200000
4962 Loading:############
4964 Bytes transferred = 1029407 (fb51f hex)
4969 => bootm $loadaddr - $oftaddr
4970 ## Booting image at 00200000 ...
4971 Image Name: Linux-2.6.17-dirty
4972 Image Type: PowerPC Linux Kernel Image (gzip compressed)
4973 Data Size: 1029343 Bytes = 1005.2 kB
4974 Load Address: 00000000
4975 Entry Point: 00000000
4976 Verifying Checksum ... OK
4977 Uncompressing Kernel Image ... OK
4978 Booting using flat device tree at 0x300000
4979 Using MPC85xx ADS machine description
4980 Memory CAM mapping: CAM0=256Mb, CAM1=256Mb, CAM2=0Mb residual: 0Mb
4984 More About U-Boot Image Types:
4985 ------------------------------
4987 U-Boot supports the following image types:
4989 "Standalone Programs" are directly runnable in the environment
4990 provided by U-Boot; it is expected that (if they behave
4991 well) you can continue to work in U-Boot after return from
4992 the Standalone Program.
4993 "OS Kernel Images" are usually images of some Embedded OS which
4994 will take over control completely. Usually these programs
4995 will install their own set of exception handlers, device
4996 drivers, set up the MMU, etc. - this means, that you cannot
4997 expect to re-enter U-Boot except by resetting the CPU.
4998 "RAMDisk Images" are more or less just data blocks, and their
4999 parameters (address, size) are passed to an OS kernel that is
5001 "Multi-File Images" contain several images, typically an OS
5002 (Linux) kernel image and one or more data images like
5003 RAMDisks. This construct is useful for instance when you want
5004 to boot over the network using BOOTP etc., where the boot
5005 server provides just a single image file, but you want to get
5006 for instance an OS kernel and a RAMDisk image.
5008 "Multi-File Images" start with a list of image sizes, each
5009 image size (in bytes) specified by an "uint32_t" in network
5010 byte order. This list is terminated by an "(uint32_t)0".
5011 Immediately after the terminating 0 follow the images, one by
5012 one, all aligned on "uint32_t" boundaries (size rounded up to
5013 a multiple of 4 bytes).
5015 "Firmware Images" are binary images containing firmware (like
5016 U-Boot or FPGA images) which usually will be programmed to
5019 "Script files" are command sequences that will be executed by
5020 U-Boot's command interpreter; this feature is especially
5021 useful when you configure U-Boot to use a real shell (hush)
5022 as command interpreter.
5024 Booting the Linux zImage:
5025 -------------------------
5027 On some platforms, it's possible to boot Linux zImage. This is done
5028 using the "bootz" command. The syntax of "bootz" command is the same
5029 as the syntax of "bootm" command.
5031 Note, defining the CONFIG_SUPPORT_INITRD_RAW allows user to supply
5032 kernel with raw initrd images. The syntax is slightly different, the
5033 address of the initrd must be augmented by it's size, in the following
5034 format: "<initrd addres>:<initrd size>".
5040 One of the features of U-Boot is that you can dynamically load and
5041 run "standalone" applications, which can use some resources of
5042 U-Boot like console I/O functions or interrupt services.
5044 Two simple examples are included with the sources:
5049 'examples/hello_world.c' contains a small "Hello World" Demo
5050 application; it is automatically compiled when you build U-Boot.
5051 It's configured to run at address 0x00040004, so you can play with it
5055 ## Ready for S-Record download ...
5056 ~>examples/hello_world.srec
5057 1 2 3 4 5 6 7 8 9 10 11 ...
5058 [file transfer complete]
5060 ## Start Addr = 0x00040004
5062 => go 40004 Hello World! This is a test.
5063 ## Starting application at 0x00040004 ...
5074 Hit any key to exit ...
5076 ## Application terminated, rc = 0x0
5078 Another example, which demonstrates how to register a CPM interrupt
5079 handler with the U-Boot code, can be found in 'examples/timer.c'.
5080 Here, a CPM timer is set up to generate an interrupt every second.
5081 The interrupt service routine is trivial, just printing a '.'
5082 character, but this is just a demo program. The application can be
5083 controlled by the following keys:
5085 ? - print current values og the CPM Timer registers
5086 b - enable interrupts and start timer
5087 e - stop timer and disable interrupts
5088 q - quit application
5091 ## Ready for S-Record download ...
5092 ~>examples/timer.srec
5093 1 2 3 4 5 6 7 8 9 10 11 ...
5094 [file transfer complete]
5096 ## Start Addr = 0x00040004
5099 ## Starting application at 0x00040004 ...
5102 tgcr @ 0xfff00980, tmr @ 0xfff00990, trr @ 0xfff00994, tcr @ 0xfff00998, tcn @ 0xfff0099c, ter @ 0xfff009b0
5105 [q, b, e, ?] Set interval 1000000 us
5108 [q, b, e, ?] ........
5109 tgcr=0x1, tmr=0xff1c, trr=0x3d09, tcr=0x0, tcn=0xef6, ter=0x0
5112 tgcr=0x1, tmr=0xff1c, trr=0x3d09, tcr=0x0, tcn=0x2ad4, ter=0x0
5115 tgcr=0x1, tmr=0xff1c, trr=0x3d09, tcr=0x0, tcn=0x1efc, ter=0x0
5118 tgcr=0x1, tmr=0xff1c, trr=0x3d09, tcr=0x0, tcn=0x169d, ter=0x0
5120 [q, b, e, ?] ...Stopping timer
5122 [q, b, e, ?] ## Application terminated, rc = 0x0
5128 Over time, many people have reported problems when trying to use the
5129 "minicom" terminal emulation program for serial download. I (wd)
5130 consider minicom to be broken, and recommend not to use it. Under
5131 Unix, I recommend to use C-Kermit for general purpose use (and
5132 especially for kermit binary protocol download ("loadb" command), and
5133 use "cu" for S-Record download ("loads" command). See
5134 http://www.denx.de/wiki/view/DULG/SystemSetup#Section_4.3.
5135 for help with kermit.
5138 Nevertheless, if you absolutely want to use it try adding this
5139 configuration to your "File transfer protocols" section:
5141 Name Program Name U/D FullScr IO-Red. Multi
5142 X kermit /usr/bin/kermit -i -l %l -s Y U Y N N
5143 Y kermit /usr/bin/kermit -i -l %l -r N D Y N N
5149 Starting at version 0.9.2, U-Boot supports NetBSD both as host
5150 (build U-Boot) and target system (boots NetBSD/mpc8xx).
5152 Building requires a cross environment; it is known to work on
5153 NetBSD/i386 with the cross-powerpc-netbsd-1.3 package (you will also
5154 need gmake since the Makefiles are not compatible with BSD make).
5155 Note that the cross-powerpc package does not install include files;
5156 attempting to build U-Boot will fail because <machine/ansi.h> is
5157 missing. This file has to be installed and patched manually:
5159 # cd /usr/pkg/cross/powerpc-netbsd/include
5161 # ln -s powerpc machine
5162 # cp /usr/src/sys/arch/powerpc/include/ansi.h powerpc/ansi.h
5163 # ${EDIT} powerpc/ansi.h ## must remove __va_list, _BSD_VA_LIST
5165 Native builds *don't* work due to incompatibilities between native
5166 and U-Boot include files.
5168 Booting assumes that (the first part of) the image booted is a
5169 stage-2 loader which in turn loads and then invokes the kernel
5170 proper. Loader sources will eventually appear in the NetBSD source
5171 tree (probably in sys/arc/mpc8xx/stand/u-boot_stage2/); in the
5172 meantime, see ftp://ftp.denx.de/pub/u-boot/ppcboot_stage2.tar.gz
5175 Implementation Internals:
5176 =========================
5178 The following is not intended to be a complete description of every
5179 implementation detail. However, it should help to understand the
5180 inner workings of U-Boot and make it easier to port it to custom
5184 Initial Stack, Global Data:
5185 ---------------------------
5187 The implementation of U-Boot is complicated by the fact that U-Boot
5188 starts running out of ROM (flash memory), usually without access to
5189 system RAM (because the memory controller is not initialized yet).
5190 This means that we don't have writable Data or BSS segments, and BSS
5191 is not initialized as zero. To be able to get a C environment working
5192 at all, we have to allocate at least a minimal stack. Implementation
5193 options for this are defined and restricted by the CPU used: Some CPU
5194 models provide on-chip memory (like the IMMR area on MPC8xx and
5195 MPC826x processors), on others (parts of) the data cache can be
5196 locked as (mis-) used as memory, etc.
5198 Chris Hallinan posted a good summary of these issues to the
5199 U-Boot mailing list:
5201 Subject: RE: [U-Boot-Users] RE: More On Memory Bank x (nothingness)?
5202 From: "Chris Hallinan" <clh@net1plus.com>
5203 Date: Mon, 10 Feb 2003 16:43:46 -0500 (22:43 MET)
5206 Correct me if I'm wrong, folks, but the way I understand it
5207 is this: Using DCACHE as initial RAM for Stack, etc, does not
5208 require any physical RAM backing up the cache. The cleverness
5209 is that the cache is being used as a temporary supply of
5210 necessary storage before the SDRAM controller is setup. It's
5211 beyond the scope of this list to explain the details, but you
5212 can see how this works by studying the cache architecture and
5213 operation in the architecture and processor-specific manuals.
5215 OCM is On Chip Memory, which I believe the 405GP has 4K. It
5216 is another option for the system designer to use as an
5217 initial stack/RAM area prior to SDRAM being available. Either
5218 option should work for you. Using CS 4 should be fine if your
5219 board designers haven't used it for something that would
5220 cause you grief during the initial boot! It is frequently not
5223 CONFIG_SYS_INIT_RAM_ADDR should be somewhere that won't interfere
5224 with your processor/board/system design. The default value
5225 you will find in any recent u-boot distribution in
5226 walnut.h should work for you. I'd set it to a value larger
5227 than your SDRAM module. If you have a 64MB SDRAM module, set
5228 it above 400_0000. Just make sure your board has no resources
5229 that are supposed to respond to that address! That code in
5230 start.S has been around a while and should work as is when
5231 you get the config right.
5236 It is essential to remember this, since it has some impact on the C
5237 code for the initialization procedures:
5239 * Initialized global data (data segment) is read-only. Do not attempt
5242 * Do not use any uninitialized global data (or implicitely initialized
5243 as zero data - BSS segment) at all - this is undefined, initiali-
5244 zation is performed later (when relocating to RAM).
5246 * Stack space is very limited. Avoid big data buffers or things like
5249 Having only the stack as writable memory limits means we cannot use
5250 normal global data to share information beween the code. But it
5251 turned out that the implementation of U-Boot can be greatly
5252 simplified by making a global data structure (gd_t) available to all
5253 functions. We could pass a pointer to this data as argument to _all_
5254 functions, but this would bloat the code. Instead we use a feature of
5255 the GCC compiler (Global Register Variables) to share the data: we
5256 place a pointer (gd) to the global data into a register which we
5257 reserve for this purpose.
5259 When choosing a register for such a purpose we are restricted by the
5260 relevant (E)ABI specifications for the current architecture, and by
5261 GCC's implementation.
5263 For PowerPC, the following registers have specific use:
5265 R2: reserved for system use
5266 R3-R4: parameter passing and return values
5267 R5-R10: parameter passing
5268 R13: small data area pointer
5272 (U-Boot also uses R12 as internal GOT pointer. r12
5273 is a volatile register so r12 needs to be reset when
5274 going back and forth between asm and C)
5276 ==> U-Boot will use R2 to hold a pointer to the global data
5278 Note: on PPC, we could use a static initializer (since the
5279 address of the global data structure is known at compile time),
5280 but it turned out that reserving a register results in somewhat
5281 smaller code - although the code savings are not that big (on
5282 average for all boards 752 bytes for the whole U-Boot image,
5283 624 text + 127 data).
5285 On Blackfin, the normal C ABI (except for P3) is followed as documented here:
5286 http://docs.blackfin.uclinux.org/doku.php?id=application_binary_interface
5288 ==> U-Boot will use P3 to hold a pointer to the global data
5290 On ARM, the following registers are used:
5292 R0: function argument word/integer result
5293 R1-R3: function argument word
5295 R10: stack limit (used only if stack checking if enabled)
5296 R11: argument (frame) pointer
5297 R12: temporary workspace
5300 R15: program counter
5302 ==> U-Boot will use R8 to hold a pointer to the global data
5304 On Nios II, the ABI is documented here:
5305 http://www.altera.com/literature/hb/nios2/n2cpu_nii51016.pdf
5307 ==> U-Boot will use gp to hold a pointer to the global data
5309 Note: on Nios II, we give "-G0" option to gcc and don't use gp
5310 to access small data sections, so gp is free.
5312 On NDS32, the following registers are used:
5314 R0-R1: argument/return
5316 R15: temporary register for assembler
5317 R16: trampoline register
5318 R28: frame pointer (FP)
5319 R29: global pointer (GP)
5320 R30: link register (LP)
5321 R31: stack pointer (SP)
5322 PC: program counter (PC)
5324 ==> U-Boot will use R10 to hold a pointer to the global data
5326 NOTE: DECLARE_GLOBAL_DATA_PTR must be used with file-global scope,
5327 or current versions of GCC may "optimize" the code too much.
5332 U-Boot runs in system state and uses physical addresses, i.e. the
5333 MMU is not used either for address mapping nor for memory protection.
5335 The available memory is mapped to fixed addresses using the memory
5336 controller. In this process, a contiguous block is formed for each
5337 memory type (Flash, SDRAM, SRAM), even when it consists of several
5338 physical memory banks.
5340 U-Boot is installed in the first 128 kB of the first Flash bank (on
5341 TQM8xxL modules this is the range 0x40000000 ... 0x4001FFFF). After
5342 booting and sizing and initializing DRAM, the code relocates itself
5343 to the upper end of DRAM. Immediately below the U-Boot code some
5344 memory is reserved for use by malloc() [see CONFIG_SYS_MALLOC_LEN
5345 configuration setting]. Below that, a structure with global Board
5346 Info data is placed, followed by the stack (growing downward).
5348 Additionally, some exception handler code is copied to the low 8 kB
5349 of DRAM (0x00000000 ... 0x00001FFF).
5351 So a typical memory configuration with 16 MB of DRAM could look like
5354 0x0000 0000 Exception Vector code
5357 0x0000 2000 Free for Application Use
5363 0x00FB FF20 Monitor Stack (Growing downward)
5364 0x00FB FFAC Board Info Data and permanent copy of global data
5365 0x00FC 0000 Malloc Arena
5368 0x00FE 0000 RAM Copy of Monitor Code
5369 ... eventually: LCD or video framebuffer
5370 ... eventually: pRAM (Protected RAM - unchanged by reset)
5371 0x00FF FFFF [End of RAM]
5374 System Initialization:
5375 ----------------------
5377 In the reset configuration, U-Boot starts at the reset entry point
5378 (on most PowerPC systems at address 0x00000100). Because of the reset
5379 configuration for CS0# this is a mirror of the onboard Flash memory.
5380 To be able to re-map memory U-Boot then jumps to its link address.
5381 To be able to implement the initialization code in C, a (small!)
5382 initial stack is set up in the internal Dual Ported RAM (in case CPUs
5383 which provide such a feature like MPC8xx or MPC8260), or in a locked
5384 part of the data cache. After that, U-Boot initializes the CPU core,
5385 the caches and the SIU.
5387 Next, all (potentially) available memory banks are mapped using a
5388 preliminary mapping. For example, we put them on 512 MB boundaries
5389 (multiples of 0x20000000: SDRAM on 0x00000000 and 0x20000000, Flash
5390 on 0x40000000 and 0x60000000, SRAM on 0x80000000). Then UPM A is
5391 programmed for SDRAM access. Using the temporary configuration, a
5392 simple memory test is run that determines the size of the SDRAM
5395 When there is more than one SDRAM bank, and the banks are of
5396 different size, the largest is mapped first. For equal size, the first
5397 bank (CS2#) is mapped first. The first mapping is always for address
5398 0x00000000, with any additional banks following immediately to create
5399 contiguous memory starting from 0.
5401 Then, the monitor installs itself at the upper end of the SDRAM area
5402 and allocates memory for use by malloc() and for the global Board
5403 Info data; also, the exception vector code is copied to the low RAM
5404 pages, and the final stack is set up.
5406 Only after this relocation will you have a "normal" C environment;
5407 until that you are restricted in several ways, mostly because you are
5408 running from ROM, and because the code will have to be relocated to a
5412 U-Boot Porting Guide:
5413 ----------------------
5415 [Based on messages by Jerry Van Baren in the U-Boot-Users mailing
5419 int main(int argc, char *argv[])
5421 sighandler_t no_more_time;
5423 signal(SIGALRM, no_more_time);
5424 alarm(PROJECT_DEADLINE - toSec (3 * WEEK));
5426 if (available_money > available_manpower) {
5427 Pay consultant to port U-Boot;
5431 Download latest U-Boot source;
5433 Subscribe to u-boot mailing list;
5436 email("Hi, I am new to U-Boot, how do I get started?");
5439 Read the README file in the top level directory;
5440 Read http://www.denx.de/twiki/bin/view/DULG/Manual;
5441 Read applicable doc/*.README;
5442 Read the source, Luke;
5443 /* find . -name "*.[chS]" | xargs grep -i <keyword> */
5446 if (available_money > toLocalCurrency ($2500))
5449 Add a lot of aggravation and time;
5451 if (a similar board exists) { /* hopefully... */
5452 cp -a board/<similar> board/<myboard>
5453 cp include/configs/<similar>.h include/configs/<myboard>.h
5455 Create your own board support subdirectory;
5456 Create your own board include/configs/<myboard>.h file;
5458 Edit new board/<myboard> files
5459 Edit new include/configs/<myboard>.h
5464 Add / modify source code;
5468 email("Hi, I am having problems...");
5470 Send patch file to the U-Boot email list;
5471 if (reasonable critiques)
5472 Incorporate improvements from email list code review;
5474 Defend code as written;
5480 void no_more_time (int sig)
5489 All contributions to U-Boot should conform to the Linux kernel
5490 coding style; see the file "Documentation/CodingStyle" and the script
5491 "scripts/Lindent" in your Linux kernel source directory.
5493 Source files originating from a different project (for example the
5494 MTD subsystem) are generally exempt from these guidelines and are not
5495 reformated to ease subsequent migration to newer versions of those
5498 Please note that U-Boot is implemented in C (and to some small parts in
5499 Assembler); no C++ is used, so please do not use C++ style comments (//)
5502 Please also stick to the following formatting rules:
5503 - remove any trailing white space
5504 - use TAB characters for indentation and vertical alignment, not spaces
5505 - make sure NOT to use DOS '\r\n' line feeds
5506 - do not add more than 2 consecutive empty lines to source files
5507 - do not add trailing empty lines to source files
5509 Submissions which do not conform to the standards may be returned
5510 with a request to reformat the changes.
5516 Since the number of patches for U-Boot is growing, we need to
5517 establish some rules. Submissions which do not conform to these rules
5518 may be rejected, even when they contain important and valuable stuff.
5520 Please see http://www.denx.de/wiki/U-Boot/Patches for details.
5522 Patches shall be sent to the u-boot mailing list <u-boot@lists.denx.de>;
5523 see http://lists.denx.de/mailman/listinfo/u-boot
5525 When you send a patch, please include the following information with
5528 * For bug fixes: a description of the bug and how your patch fixes
5529 this bug. Please try to include a way of demonstrating that the
5530 patch actually fixes something.
5532 * For new features: a description of the feature and your
5535 * A CHANGELOG entry as plaintext (separate from the patch)
5537 * For major contributions, your entry to the CREDITS file
5539 * When you add support for a new board, don't forget to add this
5540 board to the MAINTAINERS file, too.
5542 * If your patch adds new configuration options, don't forget to
5543 document these in the README file.
5545 * The patch itself. If you are using git (which is *strongly*
5546 recommended) you can easily generate the patch using the
5547 "git format-patch". If you then use "git send-email" to send it to
5548 the U-Boot mailing list, you will avoid most of the common problems
5549 with some other mail clients.
5551 If you cannot use git, use "diff -purN OLD NEW". If your version of
5552 diff does not support these options, then get the latest version of
5555 The current directory when running this command shall be the parent
5556 directory of the U-Boot source tree (i. e. please make sure that
5557 your patch includes sufficient directory information for the
5560 We prefer patches as plain text. MIME attachments are discouraged,
5561 and compressed attachments must not be used.
5563 * If one logical set of modifications affects or creates several
5564 files, all these changes shall be submitted in a SINGLE patch file.
5566 * Changesets that contain different, unrelated modifications shall be
5567 submitted as SEPARATE patches, one patch per changeset.
5572 * Before sending the patch, run the MAKEALL script on your patched
5573 source tree and make sure that no errors or warnings are reported
5574 for any of the boards.
5576 * Keep your modifications to the necessary minimum: A patch
5577 containing several unrelated changes or arbitrary reformats will be
5578 returned with a request to re-formatting / split it.
5580 * If you modify existing code, make sure that your new code does not
5581 add to the memory footprint of the code ;-) Small is beautiful!
5582 When adding new features, these should compile conditionally only
5583 (using #ifdef), and the resulting code with the new feature
5584 disabled must not need more memory than the old code without your
5587 * Remember that there is a size limit of 100 kB per message on the
5588 u-boot mailing list. Bigger patches will be moderated. If they are
5589 reasonable and not too big, they will be acknowledged. But patches
5590 bigger than the size limit should be avoided.
projects / platform / kernel / u-boot.git / blob