2 # (C) Copyright 2000 - 2004
3 # Wolfgang Denk, DENX Software Engineering, wd@denx.de.
5 # See file CREDITS for list of people who contributed to this
8 # This program is free software; you can redistribute it and/or
9 # modify it under the terms of the GNU General Public License as
10 # published by the Free Software Foundation; either version 2 of
11 # the License, or (at your option) any later version.
13 # This program is distributed in the hope that it will be useful,
14 # but WITHOUT ANY WARRANTY; without even the implied warranty of
15 # MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the
16 # GNU General Public License for more details.
18 # You should have received a copy of the GNU General Public License
19 # along with this program; if not, write to the Free Software
20 # Foundation, Inc., 59 Temple Place, Suite 330, Boston,
27 This directory contains the source code for U-Boot, a boot loader for
28 Embedded boards based on PowerPC and ARM processors, which can be
29 installed in a boot ROM and used to initialize and test the hardware
30 or to download and run application code.
32 The development of U-Boot is closely related to Linux: some parts of
33 the source code originate in the Linux source tree, we have some
34 header files in common, and special provision has been made to
35 support booting of Linux images.
37 Some attention has been paid to make this software easily
38 configurable and extendable. For instance, all monitor commands are
39 implemented with the same call interface, so that it's very easy to
40 add new commands. Also, instead of permanently adding rarely used
41 code (for instance hardware test utilities) to the monitor, you can
42 load and run it dynamically.
48 In general, all boards for which a configuration option exists in the
49 Makefile have been tested to some extent and can be considered
50 "working". In fact, many of them are used in production systems.
52 In case of problems see the CHANGELOG and CREDITS files to find out
53 who contributed the specific port.
59 In case you have questions about, problems with or contributions for
60 U-Boot you should send a message to the U-Boot mailing list at
61 <u-boot-users@lists.sourceforge.net>. There is also an archive of
62 previous traffic on the mailing list - please search the archive
63 before asking FAQ's. Please see
64 http://lists.sourceforge.net/lists/listinfo/u-boot-users/
70 - start from 8xxrom sources
71 - create PPCBoot project (http://sourceforge.net/projects/ppcboot)
73 - make it easier to add custom boards
74 - make it possible to add other [PowerPC] CPUs
75 - extend functions, especially:
76 * Provide extended interface to Linux boot loader
79 * PCMCIA / CompactFLash / ATA disk / SCSI ... boot
80 - create ARMBoot project (http://sourceforge.net/projects/armboot)
81 - add other CPU families (starting with ARM)
82 - create U-Boot project (http://sourceforge.net/projects/u-boot)
88 The "official" name of this project is "Das U-Boot". The spelling
89 "U-Boot" shall be used in all written text (documentation, comments
90 in source files etc.). Example:
92 This is the README file for the U-Boot project.
94 File names etc. shall be based on the string "u-boot". Examples:
96 include/asm-ppc/u-boot.h
98 #include <asm/u-boot.h>
100 Variable names, preprocessor constants etc. shall be either based on
101 the string "u_boot" or on "U_BOOT". Example:
103 U_BOOT_VERSION u_boot_logo
104 IH_OS_U_BOOT u_boot_hush_start
110 U-Boot uses a 3 level version number containing a version, a
111 sub-version, and a patchlevel: "U-Boot-2.34.5" means version "2",
112 sub-version "34", and patchlevel "4".
114 The patchlevel is used to indicate certain stages of development
115 between released versions, i. e. officially released versions of
116 U-Boot will always have a patchlevel of "0".
122 - board Board dependent files
123 - common Misc architecture independent functions
124 - cpu CPU specific files
125 - 74xx_7xx Files specific to Motorola MPC74xx and 7xx CPUs
126 - arm720t Files specific to ARM 720 CPUs
127 - arm920t Files specific to ARM 920 CPUs
128 - imx Files specific to Motorola MC9328 i.MX CPUs
129 - s3c24x0 Files specific to Samsung S3C24X0 CPUs
130 - arm925t Files specific to ARM 925 CPUs
131 - arm926ejs Files specific to ARM 926 CPUs
132 - at91rm9200 Files specific to Atmel AT91RM9200 CPUs
133 - i386 Files specific to i386 CPUs
134 - ixp Files specific to Intel XScale IXP CPUs
135 - mcf52x2 Files specific to Motorola ColdFire MCF52x2 CPUs
136 - mips Files specific to MIPS CPUs
137 - mpc5xx Files specific to Motorola MPC5xx CPUs
138 - mpc5xxx Files specific to Motorola MPC5xxx CPUs
139 - mpc8xx Files specific to Motorola MPC8xx CPUs
140 - mpc824x Files specific to Motorola MPC824x CPUs
141 - mpc8260 Files specific to Motorola MPC8260 CPUs
142 - mpc85xx Files specific to Motorola MPC85xx CPUs
143 - nios Files specific to Altera NIOS CPUs
144 - ppc4xx Files specific to IBM PowerPC 4xx CPUs
145 - pxa Files specific to Intel XScale PXA CPUs
146 - s3c44b0 Files specific to Samsung S3C44B0 CPUs
147 - sa1100 Files specific to Intel StrongARM SA1100 CPUs
148 - disk Code for disk drive partition handling
149 - doc Documentation (don't expect too much)
150 - drivers Commonly used device drivers
151 - dtt Digital Thermometer and Thermostat drivers
152 - examples Example code for standalone applications, etc.
153 - include Header Files
154 - lib_arm Files generic to ARM architecture
155 - lib_generic Files generic to all architectures
156 - lib_i386 Files generic to i386 architecture
157 - lib_m68k Files generic to m68k architecture
158 - lib_mips Files generic to MIPS architecture
159 - lib_nios Files generic to NIOS architecture
160 - lib_ppc Files generic to PowerPC architecture
161 - net Networking code
162 - post Power On Self Test
163 - rtc Real Time Clock drivers
164 - tools Tools to build S-Record or U-Boot images, etc.
166 Software Configuration:
167 =======================
169 Configuration is usually done using C preprocessor defines; the
170 rationale behind that is to avoid dead code whenever possible.
172 There are two classes of configuration variables:
174 * Configuration _OPTIONS_:
175 These are selectable by the user and have names beginning with
178 * Configuration _SETTINGS_:
179 These depend on the hardware etc. and should not be meddled with if
180 you don't know what you're doing; they have names beginning with
183 Later we will add a configuration tool - probably similar to or even
184 identical to what's used for the Linux kernel. Right now, we have to
185 do the configuration by hand, which means creating some symbolic
186 links and editing some configuration files. We use the TQM8xxL boards
190 Selection of Processor Architecture and Board Type:
191 ---------------------------------------------------
193 For all supported boards there are ready-to-use default
194 configurations available; just type "make <board_name>_config".
196 Example: For a TQM823L module type:
201 For the Cogent platform, you need to specify the cpu type as well;
202 e.g. "make cogent_mpc8xx_config". And also configure the cogent
203 directory according to the instructions in cogent/README.
206 Configuration Options:
207 ----------------------
209 Configuration depends on the combination of board and CPU type; all
210 such information is kept in a configuration file
211 "include/configs/<board_name>.h".
213 Example: For a TQM823L module, all configuration settings are in
214 "include/configs/TQM823L.h".
217 Many of the options are named exactly as the corresponding Linux
218 kernel configuration options. The intention is to make it easier to
219 build a config tool - later.
222 The following options need to be configured:
224 - CPU Type: Define exactly one of
228 CONFIG_MPC823, CONFIG_MPC850, CONFIG_MPC855, CONFIG_MPC860
230 or CONFIG_MPC824X, CONFIG_MPC8260
245 MicroBlaze based CPUs:
246 ----------------------
250 - Board Type: Define exactly one of
252 PowerPC based boards:
253 ---------------------
255 CONFIG_ADCIOP CONFIG_GEN860T CONFIG_PCI405
256 CONFIG_ADS860 CONFIG_GENIETV CONFIG_PCIPPC2
257 CONFIG_AMX860 CONFIG_GTH CONFIG_PCIPPC6
258 CONFIG_AR405 CONFIG_gw8260 CONFIG_pcu_e
259 CONFIG_BAB7xx CONFIG_hermes CONFIG_PIP405
260 CONFIG_c2mon CONFIG_hymod CONFIG_PM826
261 CONFIG_CANBT CONFIG_IAD210 CONFIG_ppmc8260
262 CONFIG_CCM CONFIG_ICU862 CONFIG_QS823
263 CONFIG_CMI CONFIG_IP860 CONFIG_QS850
264 CONFIG_cogent_mpc8260 CONFIG_IPHASE4539 CONFIG_QS860T
265 CONFIG_cogent_mpc8xx CONFIG_IVML24 CONFIG_RBC823
266 CONFIG_CPCI405 CONFIG_IVML24_128 CONFIG_RPXClassic
267 CONFIG_CPCI4052 CONFIG_IVML24_256 CONFIG_RPXlite
268 CONFIG_CPCIISER4 CONFIG_IVMS8 CONFIG_RPXsuper
269 CONFIG_CPU86 CONFIG_IVMS8_128 CONFIG_rsdproto
270 CONFIG_CRAYL1 CONFIG_IVMS8_256 CONFIG_sacsng
271 CONFIG_CSB272 CONFIG_JSE CONFIG_Sandpoint8240
272 CONFIG_CU824 CONFIG_LANTEC CONFIG_Sandpoint8245
273 CONFIG_DASA_SIM CONFIG_lwmon CONFIG_sbc8260
274 CONFIG_DB64360 CONFIG_MBX CONFIG_sbc8560
275 CONFIG_DB64460 CONFIG_MBX860T CONFIG_SM850
276 CONFIG_DU405 CONFIG_MHPC CONFIG_SPD823TS
277 CONFIG_DUET_ADS CONFIG_MIP405 CONFIG_STXGP3
278 CONFIG_EBONY CONFIG_MOUSSE CONFIG_SXNI855T
279 CONFIG_ELPPC CONFIG_MPC8260ADS CONFIG_TQM823L
280 CONFIG_ELPT860 CONFIG_MPC8540ADS CONFIG_TQM8260
281 CONFIG_ep8260 CONFIG_MPC8560ADS CONFIG_TQM850L
282 CONFIG_ERIC CONFIG_MUSENKI CONFIG_TQM855L
283 CONFIG_ESTEEM192E CONFIG_MVS1 CONFIG_TQM860L
284 CONFIG_ETX094 CONFIG_NETPHONE CONFIG_TTTech
285 CONFIG_EVB64260 CONFIG_NETTA CONFIG_UTX8245
286 CONFIG_FADS823 CONFIG_NETVIA CONFIG_V37
287 CONFIG_FADS850SAR CONFIG_NX823 CONFIG_W7OLMC
288 CONFIG_FADS860T CONFIG_OCRTC CONFIG_W7OLMG
289 CONFIG_FLAGADM CONFIG_ORSG CONFIG_WALNUT405
290 CONFIG_FPS850L CONFIG_OXC CONFIG_ZPC1900
291 CONFIG_FPS860L CONFIG_ZUMA
296 CONFIG_AT91RM9200DK, CONFIG_CERF250, CONFIG_DNP1110,
297 CONFIG_EP7312, CONFIG_H2_OMAP1610, CONFIG_HHP_CRADLE,
298 CONFIG_IMPA7, CONFIG_INNOVATOROMAP1510, CONFIG_INNOVATOROMAP1610,
299 CONFIG_LART, CONFIG_LPD7A400 CONFIG_LUBBOCK,
300 CONFIG_OSK_OMAP5912, CONFIG_SHANNON, CONFIG_P2_OMAP730,
301 CONFIG_SMDK2400, CONFIG_SMDK2410, CONFIG_TRAB,
304 MicroBlaze based boards:
305 ------------------------
310 - CPU Module Type: (if CONFIG_COGENT is defined)
311 Define exactly one of
313 --- FIXME --- not tested yet:
314 CONFIG_CMA286_60, CONFIG_CMA286_21, CONFIG_CMA286_60P,
315 CONFIG_CMA287_23, CONFIG_CMA287_50
317 - Motherboard Type: (if CONFIG_COGENT is defined)
318 Define exactly one of
319 CONFIG_CMA101, CONFIG_CMA102
321 - Motherboard I/O Modules: (if CONFIG_COGENT is defined)
322 Define one or more of
325 - Motherboard Options: (if CONFIG_CMA101 or CONFIG_CMA102 are defined)
326 Define one or more of
327 CONFIG_LCD_HEARTBEAT - update a character position on
328 the lcd display every second with
331 - Board flavour: (if CONFIG_MPC8260ADS is defined)
334 CFG_8260ADS - original MPC8260ADS
335 CFG_8266ADS - MPC8266ADS
336 CFG_PQ2FADS - PQ2FADS-ZU or PQ2FADS-VR
337 CFG_8272ADS - MPC8272ADS
339 - MPC824X Family Member (if CONFIG_MPC824X is defined)
340 Define exactly one of
341 CONFIG_MPC8240, CONFIG_MPC8245
343 - 8xx CPU Options: (if using an MPC8xx cpu)
344 CONFIG_8xx_GCLK_FREQ - deprecated: CPU clock if
345 get_gclk_freq() cannot work
346 e.g. if there is no 32KHz
347 reference PIT/RTC clock
348 CONFIG_8xx_OSCLK - PLL input clock (either EXTCLK
351 - 859/866/885 CPU options: (if using a MPC859 or MPC866 or MPC885 CPU):
354 CONFIG_8xx_CPUCLK_DEFAULT
355 See doc/README.MPC866
359 Define this to measure the actual CPU clock instead
360 of relying on the correctness of the configured
361 values. Mostly useful for board bringup to make sure
362 the PLL is locked at the intended frequency. Note
363 that this requires a (stable) reference clock (32 kHz
364 RTC clock or CFG_8XX_XIN)
366 - Linux Kernel Interface:
369 U-Boot stores all clock information in Hz
370 internally. For binary compatibility with older Linux
371 kernels (which expect the clocks passed in the
372 bd_info data to be in MHz) the environment variable
373 "clocks_in_mhz" can be defined so that U-Boot
374 converts clock data to MHZ before passing it to the
376 When CONFIG_CLOCKS_IN_MHZ is defined, a definition of
377 "clocks_in_mhz=1" is automatically included in the
380 CONFIG_MEMSIZE_IN_BYTES [relevant for MIPS only]
382 When transfering memsize parameter to linux, some versions
383 expect it to be in bytes, others in MB.
384 Define CONFIG_MEMSIZE_IN_BYTES to make it in bytes.
389 Define this if you want support for Amba PrimeCell PL010 UARTs.
393 Define this if you want support for Amba PrimeCell PL011 UARTs.
397 If you have Amba PrimeCell PL011 UARTs, set this variable to
398 the clock speed of the UARTs.
402 If you have Amba PrimeCell PL010 or PL011 UARTs on your board,
403 define this to a list of base addresses for each (supported)
404 port. See e.g. include/configs/versatile.h
408 Depending on board, define exactly one serial port
409 (like CONFIG_8xx_CONS_SMC1, CONFIG_8xx_CONS_SMC2,
410 CONFIG_8xx_CONS_SCC1, ...), or switch off the serial
411 console by defining CONFIG_8xx_CONS_NONE
413 Note: if CONFIG_8xx_CONS_NONE is defined, the serial
414 port routines must be defined elsewhere
415 (i.e. serial_init(), serial_getc(), ...)
418 Enables console device for a color framebuffer. Needs following
419 defines (cf. smiLynxEM, i8042, board/eltec/bab7xx)
420 VIDEO_FB_LITTLE_ENDIAN graphic memory organisation
422 VIDEO_HW_RECTFILL graphic chip supports
425 VIDEO_HW_BITBLT graphic chip supports
426 bit-blit (cf. smiLynxEM)
427 VIDEO_VISIBLE_COLS visible pixel columns
429 VIDEO_VISIBLE_ROWS visible pixel rows
430 VIDEO_PIXEL_SIZE bytes per pixel
431 VIDEO_DATA_FORMAT graphic data format
432 (0-5, cf. cfb_console.c)
433 VIDEO_FB_ADRS framebuffer address
434 VIDEO_KBD_INIT_FCT keyboard int fct
435 (i.e. i8042_kbd_init())
436 VIDEO_TSTC_FCT test char fct
438 VIDEO_GETC_FCT get char fct
440 CONFIG_CONSOLE_CURSOR cursor drawing on/off
441 (requires blink timer
443 CFG_CONSOLE_BLINK_COUNT blink interval (cf. i8042.c)
444 CONFIG_CONSOLE_TIME display time/date info in
446 (requires CFG_CMD_DATE)
447 CONFIG_VIDEO_LOGO display Linux logo in
449 CONFIG_VIDEO_BMP_LOGO use bmp_logo.h instead of
450 linux_logo.h for logo.
451 Requires CONFIG_VIDEO_LOGO
452 CONFIG_CONSOLE_EXTRA_INFO
453 addional board info beside
456 When CONFIG_CFB_CONSOLE is defined, video console is
457 default i/o. Serial console can be forced with
458 environment 'console=serial'.
460 When CONFIG_SILENT_CONSOLE is defined, all console
461 messages (by U-Boot and Linux!) can be silenced with
462 the "silent" environment variable. See
463 doc/README.silent for more information.
466 CONFIG_BAUDRATE - in bps
467 Select one of the baudrates listed in
468 CFG_BAUDRATE_TABLE, see below.
469 CFG_BRGCLK_PRESCALE, baudrate prescale
471 - Interrupt driven serial port input:
472 CONFIG_SERIAL_SOFTWARE_FIFO
475 Use an interrupt handler for receiving data on the
476 serial port. It also enables using hardware handshake
477 (RTS/CTS) and UART's built-in FIFO. Set the number of
478 bytes the interrupt driven input buffer should have.
480 Leave undefined to disable this feature, including
481 disable the buffer and hardware handshake.
483 - Console UART Number:
487 If defined internal UART1 (and not UART0) is used
488 as default U-Boot console.
490 - Boot Delay: CONFIG_BOOTDELAY - in seconds
491 Delay before automatically booting the default image;
492 set to -1 to disable autoboot.
494 See doc/README.autoboot for these options that
495 work with CONFIG_BOOTDELAY. None are required.
496 CONFIG_BOOT_RETRY_TIME
497 CONFIG_BOOT_RETRY_MIN
498 CONFIG_AUTOBOOT_KEYED
499 CONFIG_AUTOBOOT_PROMPT
500 CONFIG_AUTOBOOT_DELAY_STR
501 CONFIG_AUTOBOOT_STOP_STR
502 CONFIG_AUTOBOOT_DELAY_STR2
503 CONFIG_AUTOBOOT_STOP_STR2
504 CONFIG_ZERO_BOOTDELAY_CHECK
505 CONFIG_RESET_TO_RETRY
509 Only needed when CONFIG_BOOTDELAY is enabled;
510 define a command string that is automatically executed
511 when no character is read on the console interface
512 within "Boot Delay" after reset.
515 This can be used to pass arguments to the bootm
516 command. The value of CONFIG_BOOTARGS goes into the
517 environment value "bootargs".
519 CONFIG_RAMBOOT and CONFIG_NFSBOOT
520 The value of these goes into the environment as
521 "ramboot" and "nfsboot" respectively, and can be used
522 as a convenience, when switching between booting from
528 When this option is #defined, the existence of the
529 environment variable "preboot" will be checked
530 immediately before starting the CONFIG_BOOTDELAY
531 countdown and/or running the auto-boot command resp.
532 entering interactive mode.
534 This feature is especially useful when "preboot" is
535 automatically generated or modified. For an example
536 see the LWMON board specific code: here "preboot" is
537 modified when the user holds down a certain
538 combination of keys on the (special) keyboard when
541 - Serial Download Echo Mode:
543 If defined to 1, all characters received during a
544 serial download (using the "loads" command) are
545 echoed back. This might be needed by some terminal
546 emulations (like "cu"), but may as well just take
547 time on others. This setting #define's the initial
548 value of the "loads_echo" environment variable.
550 - Kgdb Serial Baudrate: (if CFG_CMD_KGDB is defined)
552 Select one of the baudrates listed in
553 CFG_BAUDRATE_TABLE, see below.
557 Most monitor functions can be selected (or
558 de-selected) by adjusting the definition of
559 CONFIG_COMMANDS; to select individual functions,
560 #define CONFIG_COMMANDS by "OR"ing any of the
563 #define enables commands:
564 -------------------------
565 CFG_CMD_ASKENV * ask for env variable
566 CFG_CMD_AUTOSCRIPT Autoscript Support
568 CFG_CMD_BEDBUG * Include BedBug Debugger
569 CFG_CMD_BMP * BMP support
570 CFG_CMD_BSP * Board specific commands
572 CFG_CMD_CACHE * icache, dcache
573 CFG_CMD_CONSOLE coninfo
574 CFG_CMD_DATE * support for RTC, date/time...
575 CFG_CMD_DHCP * DHCP support
576 CFG_CMD_DIAG * Diagnostics
577 CFG_CMD_DOC * Disk-On-Chip Support
578 CFG_CMD_DTT * Digital Therm and Thermostat
579 CFG_CMD_ECHO * echo arguments
580 CFG_CMD_EEPROM * EEPROM read/write support
581 CFG_CMD_ELF * bootelf, bootvx
583 CFG_CMD_FDC * Floppy Disk Support
584 CFG_CMD_FAT * FAT partition support
585 CFG_CMD_FDOS * Dos diskette Support
586 CFG_CMD_FLASH flinfo, erase, protect
587 CFG_CMD_FPGA FPGA device initialization support
588 CFG_CMD_HWFLOW * RTS/CTS hw flow control
589 CFG_CMD_I2C * I2C serial bus support
590 CFG_CMD_IDE * IDE harddisk support
592 CFG_CMD_IMLS List all found images
593 CFG_CMD_IMMAP * IMMR dump support
594 CFG_CMD_IRQ * irqinfo
595 CFG_CMD_ITEST Integer/string test of 2 values
596 CFG_CMD_JFFS2 * JFFS2 Support
600 CFG_CMD_MEMORY md, mm, nm, mw, cp, cmp, crc, base,
602 CFG_CMD_MISC Misc functions like sleep etc
603 CFG_CMD_MMC * MMC memory mapped support
604 CFG_CMD_MII * MII utility commands
605 CFG_CMD_NAND * NAND support
606 CFG_CMD_NET bootp, tftpboot, rarpboot
607 CFG_CMD_PCI * pciinfo
608 CFG_CMD_PCMCIA * PCMCIA support
609 CFG_CMD_PING * send ICMP ECHO_REQUEST to network host
610 CFG_CMD_PORTIO * Port I/O
611 CFG_CMD_REGINFO * Register dump
612 CFG_CMD_RUN run command in env variable
613 CFG_CMD_SAVES * save S record dump
614 CFG_CMD_SCSI * SCSI Support
615 CFG_CMD_SDRAM * print SDRAM configuration information
616 CFG_CMD_SETGETDCR Support for DCR Register access (4xx only)
617 CFG_CMD_SPI * SPI serial bus support
618 CFG_CMD_USB * USB support
619 CFG_CMD_VFD * VFD support (TRAB)
620 CFG_CMD_BSP * Board SPecific functions
621 CFG_CMD_CDP * Cisco Discover Protocol support
622 -----------------------------------------------
625 CONFIG_CMD_DFL Default configuration; at the moment
626 this is includes all commands, except
627 the ones marked with "*" in the list
630 If you don't define CONFIG_COMMANDS it defaults to
631 CONFIG_CMD_DFL in include/cmd_confdefs.h. A board can
632 override the default settings in the respective
635 EXAMPLE: If you want all functions except of network
636 support you can write:
638 #define CONFIG_COMMANDS (CFG_CMD_ALL & ~CFG_CMD_NET)
641 Note: Don't enable the "icache" and "dcache" commands
642 (configuration option CFG_CMD_CACHE) unless you know
643 what you (and your U-Boot users) are doing. Data
644 cache cannot be enabled on systems like the 8xx or
645 8260 (where accesses to the IMMR region must be
646 uncached), and it cannot be disabled on all other
647 systems where we (mis-) use the data cache to hold an
648 initial stack and some data.
651 XXX - this list needs to get updated!
655 If this variable is defined, it enables watchdog
656 support. There must be support in the platform specific
657 code for a watchdog. For the 8xx and 8260 CPUs, the
658 SIU Watchdog feature is enabled in the SYPCR
662 CONFIG_VERSION_VARIABLE
663 If this variable is defined, an environment variable
664 named "ver" is created by U-Boot showing the U-Boot
665 version as printed by the "version" command.
666 This variable is readonly.
670 When CFG_CMD_DATE is selected, the type of the RTC
671 has to be selected, too. Define exactly one of the
674 CONFIG_RTC_MPC8xx - use internal RTC of MPC8xx
675 CONFIG_RTC_PCF8563 - use Philips PCF8563 RTC
676 CONFIG_RTC_MC146818 - use MC146818 RTC
677 CONFIG_RTC_DS1307 - use Maxim, Inc. DS1307 RTC
678 CONFIG_RTC_DS1337 - use Maxim, Inc. DS1337 RTC
679 CONFIG_RTC_DS1338 - use Maxim, Inc. DS1338 RTC
680 CONFIG_RTC_DS164x - use Dallas DS164x RTC
681 CONFIG_RTC_MAX6900 - use Maxim, Inc. MAX6900 RTC
683 Note that if the RTC uses I2C, then the I2C interface
684 must also be configured. See I2C Support, below.
688 When CONFIG_TIMESTAMP is selected, the timestamp
689 (date and time) of an image is printed by image
690 commands like bootm or iminfo. This option is
691 automatically enabled when you select CFG_CMD_DATE .
694 CONFIG_MAC_PARTITION and/or CONFIG_DOS_PARTITION
695 and/or CONFIG_ISO_PARTITION
697 If IDE or SCSI support is enabled (CFG_CMD_IDE or
698 CFG_CMD_SCSI) you must configure support for at least
699 one partition type as well.
702 CONFIG_IDE_RESET_ROUTINE - this is defined in several
703 board configurations files but used nowhere!
705 CONFIG_IDE_RESET - is this is defined, IDE Reset will
706 be performed by calling the function
707 ide_set_reset(int reset)
708 which has to be defined in a board specific file
713 Set this to enable ATAPI support.
718 Set this to enable support for disks larger than 137GB
719 Also look at CFG_64BIT_LBA ,CFG_64BIT_VSPRINTF and CFG_64BIT_STRTOUL
720 Whithout these , LBA48 support uses 32bit variables and will 'only'
721 support disks up to 2.1TB.
724 When enabled, makes the IDE subsystem use 64bit sector addresses.
728 At the moment only there is only support for the
729 SYM53C8XX SCSI controller; define
730 CONFIG_SCSI_SYM53C8XX to enable it.
732 CFG_SCSI_MAX_LUN [8], CFG_SCSI_MAX_SCSI_ID [7] and
733 CFG_SCSI_MAX_DEVICE [CFG_SCSI_MAX_SCSI_ID *
734 CFG_SCSI_MAX_LUN] can be adjusted to define the
735 maximum numbers of LUNs, SCSI ID's and target
737 CFG_SCSI_SYM53C8XX_CCF to fix clock timing (80Mhz)
739 - NETWORK Support (PCI):
741 Support for Intel 8254x gigabit chips.
744 Support for Intel 82557/82559/82559ER chips.
745 Optional CONFIG_EEPRO100_SROM_WRITE enables eeprom
746 write routine for first time initialisation.
749 Support for Digital 2114x chips.
750 Optional CONFIG_TULIP_SELECT_MEDIA for board specific
751 modem chip initialisation (KS8761/QS6611).
754 Support for National dp83815 chips.
757 Support for National dp8382[01] gigabit chips.
759 - NETWORK Support (other):
761 CONFIG_DRIVER_LAN91C96
762 Support for SMSC's LAN91C96 chips.
765 Define this to hold the physical address
766 of the LAN91C96's I/O space
768 CONFIG_LAN91C96_USE_32_BIT
769 Define this to enable 32 bit addressing
771 CONFIG_DRIVER_SMC91111
772 Support for SMSC's LAN91C111 chip
775 Define this to hold the physical address
776 of the device (I/O space)
778 CONFIG_SMC_USE_32_BIT
779 Define this if data bus is 32 bits
781 CONFIG_SMC_USE_IOFUNCS
782 Define this to use i/o functions instead of macros
783 (some hardware wont work with macros)
786 At the moment only the UHCI host controller is
787 supported (PIP405, MIP405, MPC5200); define
788 CONFIG_USB_UHCI to enable it.
789 define CONFIG_USB_KEYBOARD to enable the USB Keyboard
790 end define CONFIG_USB_STORAGE to enable the USB
793 Supported are USB Keyboards and USB Floppy drives
795 MPC5200 USB requires additional defines:
797 for 528 MHz Clock: 0x0001bbbb
799 for differential drivers: 0x00001000
800 for single ended drivers: 0x00005000
804 The MMC controller on the Intel PXA is supported. To
805 enable this define CONFIG_MMC. The MMC can be
806 accessed from the boot prompt by mapping the device
807 to physical memory similar to flash. Command line is
808 enabled with CFG_CMD_MMC. The MMC driver also works with
809 the FAT fs. This is enabled with CFG_CMD_FAT.
811 - Journaling Flash filesystem support:
812 CONFIG_JFFS2_NAND, CONFIG_JFFS2_NAND_OFF, CONFIG_JFFS2_NAND_SIZE,
813 CONFIG_JFFS2_NAND_DEV
814 Define these for a default partition on a NAND device
816 CFG_JFFS2_FIRST_SECTOR,
817 CFG_JFFS2_FIRST_BANK, CFG_JFFS2_NUM_BANKS
818 Define these for a default partition on a NOR device
821 Define this to create an own partition. You have to provide a
822 function struct part_info* jffs2_part_info(int part_num)
824 If you define only one JFFS2 partition you may also want to
825 #define CFG_JFFS_SINGLE_PART 1
826 to disable the command chpart. This is the default when you
827 have not defined a custom partition
832 Define this to enable standard (PC-Style) keyboard
836 Standard PC keyboard driver with US (is default) and
837 GERMAN key layout (switch via environment 'keymap=de') support.
838 Export function i8042_kbd_init, i8042_tstc and i8042_getc
839 for cfb_console. Supports cursor blinking.
844 Define this to enable video support (for output to
849 Enable Chips & Technologies 69000 Video chip
851 CONFIG_VIDEO_SMI_LYNXEM
852 Enable Silicon Motion SMI 712/710/810 Video chip. The
853 video output is selected via environment 'videoout'
854 (1 = LCD and 2 = CRT). If videoout is undefined, CRT is
857 For the CT69000 and SMI_LYNXEM drivers, videomode is
858 selected via environment 'videomode'. Two diferent ways
860 - "videomode=num" 'num' is a standard LiLo mode numbers.
861 Following standard modes are supported (* is default):
863 Colors 640x480 800x600 1024x768 1152x864 1280x1024
864 -------------+---------------------------------------------
865 8 bits | 0x301* 0x303 0x305 0x161 0x307
866 15 bits | 0x310 0x313 0x316 0x162 0x319
867 16 bits | 0x311 0x314 0x317 0x163 0x31A
868 24 bits | 0x312 0x315 0x318 ? 0x31B
869 -------------+---------------------------------------------
870 (i.e. setenv videomode 317; saveenv; reset;)
872 - "videomode=bootargs" all the video parameters are parsed
873 from the bootargs. (See drivers/videomodes.c)
876 CONFIG_VIDEO_SED13806
877 Enable Epson SED13806 driver. This driver supports 8bpp
878 and 16bpp modes defined by CONFIG_VIDEO_SED13806_8BPP
879 or CONFIG_VIDEO_SED13806_16BPP
884 Define this to enable a custom keyboard support.
885 This simply calls drv_keyboard_init() which must be
886 defined in your board-specific files.
887 The only board using this so far is RBC823.
889 - LCD Support: CONFIG_LCD
891 Define this to enable LCD support (for output to LCD
892 display); also select one of the supported displays
893 by defining one of these:
895 CONFIG_NEC_NL6448AC33:
897 NEC NL6448AC33-18. Active, color, single scan.
899 CONFIG_NEC_NL6448BC20
901 NEC NL6448BC20-08. 6.5", 640x480.
902 Active, color, single scan.
904 CONFIG_NEC_NL6448BC33_54
906 NEC NL6448BC33-54. 10.4", 640x480.
907 Active, color, single scan.
911 Sharp 320x240. Active, color, single scan.
912 It isn't 16x9, and I am not sure what it is.
914 CONFIG_SHARP_LQ64D341
916 Sharp LQ64D341 display, 640x480.
917 Active, color, single scan.
921 HLD1045 display, 640x480.
922 Active, color, single scan.
926 Optrex CBL50840-2 NF-FW 99 22 M5
928 Hitachi LMG6912RPFC-00T
932 320x240. Black & white.
934 Normally display is black on white background; define
935 CFG_WHITE_ON_BLACK to get it inverted.
937 - Splash Screen Support: CONFIG_SPLASH_SCREEN
939 If this option is set, the environment is checked for
940 a variable "splashimage". If found, the usual display
941 of logo, copyright and system information on the LCD
942 is suppressed and the BMP image at the address
943 specified in "splashimage" is loaded instead. The
944 console is redirected to the "nulldev", too. This
945 allows for a "silent" boot where a splash screen is
946 loaded very quickly after power-on.
948 - Compression support:
951 If this option is set, support for bzip2 compressed
952 images is included. If not, only uncompressed and gzip
953 compressed images are supported.
955 NOTE: the bzip2 algorithm requires a lot of RAM, so
956 the malloc area (as defined by CFG_MALLOC_LEN) should
962 The address of PHY on MII bus.
964 CONFIG_PHY_CLOCK_FREQ (ppc4xx)
966 The clock frequency of the MII bus
970 If this option is set, support for speed/duplex
971 detection of Gigabit PHY is included.
973 CONFIG_PHY_RESET_DELAY
975 Some PHY like Intel LXT971A need extra delay after
976 reset before any MII register access is possible.
977 For such PHY, set this option to the usec delay
978 required. (minimum 300usec for LXT971A)
980 CONFIG_PHY_CMD_DELAY (ppc4xx)
982 Some PHY like Intel LXT971A need extra delay after
983 command issued before MII status register can be read
990 Define a default value for ethernet address to use
991 for the respective ethernet interface, in case this
992 is not determined automatically.
997 Define a default value for the IP address to use for
998 the default ethernet interface, in case this is not
999 determined through e.g. bootp.
1001 - Server IP address:
1004 Defines a default value for theIP address of a TFTP
1005 server to contact when using the "tftboot" command.
1007 - BOOTP Recovery Mode:
1008 CONFIG_BOOTP_RANDOM_DELAY
1010 If you have many targets in a network that try to
1011 boot using BOOTP, you may want to avoid that all
1012 systems send out BOOTP requests at precisely the same
1013 moment (which would happen for instance at recovery
1014 from a power failure, when all systems will try to
1015 boot, thus flooding the BOOTP server. Defining
1016 CONFIG_BOOTP_RANDOM_DELAY causes a random delay to be
1017 inserted before sending out BOOTP requests. The
1018 following delays are insterted then:
1020 1st BOOTP request: delay 0 ... 1 sec
1021 2nd BOOTP request: delay 0 ... 2 sec
1022 3rd BOOTP request: delay 0 ... 4 sec
1024 BOOTP requests: delay 0 ... 8 sec
1026 - DHCP Advanced Options:
1029 You can fine tune the DHCP functionality by adding
1030 these flags to the CONFIG_BOOTP_MASK define:
1032 CONFIG_BOOTP_DNS2 - If a DHCP client requests the DNS
1033 serverip from a DHCP server, it is possible that more
1034 than one DNS serverip is offered to the client.
1035 If CONFIG_BOOTP_DNS2 is enabled, the secondary DNS
1036 serverip will be stored in the additional environment
1037 variable "dnsip2". The first DNS serverip is always
1038 stored in the variable "dnsip", when CONFIG_BOOTP_DNS
1039 is added to the CONFIG_BOOTP_MASK.
1041 CONFIG_BOOTP_SEND_HOSTNAME - Some DHCP servers are capable
1042 to do a dynamic update of a DNS server. To do this, they
1043 need the hostname of the DHCP requester.
1044 If CONFIG_BOOP_SEND_HOSTNAME is added to the
1045 CONFIG_BOOTP_MASK, the content of the "hostname"
1046 environment variable is passed as option 12 to
1050 CONFIG_CDP_DEVICE_ID
1052 The device id used in CDP trigger frames.
1054 CONFIG_CDP_DEVICE_ID_PREFIX
1056 A two character string which is prefixed to the MAC address
1061 A printf format string which contains the ascii name of
1062 the port. Normally is set to "eth%d" which sets
1063 eth0 for the first ethernet, eth1 for the second etc.
1065 CONFIG_CDP_CAPABILITIES
1067 A 32bit integer which indicates the device capabilities;
1068 0x00000010 for a normal host which does not forwards.
1072 An ascii string containing the version of the software.
1076 An ascii string containing the name of the platform.
1080 A 32bit integer sent on the trigger.
1082 CONFIG_CDP_POWER_CONSUMPTION
1084 A 16bit integer containing the power consumption of the
1085 device in .1 of milliwatts.
1087 CONFIG_CDP_APPLIANCE_VLAN_TYPE
1089 A byte containing the id of the VLAN.
1091 - Status LED: CONFIG_STATUS_LED
1093 Several configurations allow to display the current
1094 status using a LED. For instance, the LED will blink
1095 fast while running U-Boot code, stop blinking as
1096 soon as a reply to a BOOTP request was received, and
1097 start blinking slow once the Linux kernel is running
1098 (supported by a status LED driver in the Linux
1099 kernel). Defining CONFIG_STATUS_LED enables this
1102 - CAN Support: CONFIG_CAN_DRIVER
1104 Defining CONFIG_CAN_DRIVER enables CAN driver support
1105 on those systems that support this (optional)
1106 feature, like the TQM8xxL modules.
1108 - I2C Support: CONFIG_HARD_I2C | CONFIG_SOFT_I2C
1110 These enable I2C serial bus commands. Defining either of
1111 (but not both of) CONFIG_HARD_I2C or CONFIG_SOFT_I2C will
1112 include the appropriate I2C driver for the selected cpu.
1114 This will allow you to use i2c commands at the u-boot
1115 command line (as long as you set CFG_CMD_I2C in
1116 CONFIG_COMMANDS) and communicate with i2c based realtime
1117 clock chips. See common/cmd_i2c.c for a description of the
1118 command line interface.
1120 CONFIG_HARD_I2C selects the CPM hardware driver for I2C.
1122 CONFIG_SOFT_I2C configures u-boot to use a software (aka
1123 bit-banging) driver instead of CPM or similar hardware
1126 There are several other quantities that must also be
1127 defined when you define CONFIG_HARD_I2C or CONFIG_SOFT_I2C.
1129 In both cases you will need to define CFG_I2C_SPEED
1130 to be the frequency (in Hz) at which you wish your i2c bus
1131 to run and CFG_I2C_SLAVE to be the address of this node (ie
1132 the cpu's i2c node address).
1134 Now, the u-boot i2c code for the mpc8xx (cpu/mpc8xx/i2c.c)
1135 sets the cpu up as a master node and so its address should
1136 therefore be cleared to 0 (See, eg, MPC823e User's Manual
1137 p.16-473). So, set CFG_I2C_SLAVE to 0.
1139 That's all that's required for CONFIG_HARD_I2C.
1141 If you use the software i2c interface (CONFIG_SOFT_I2C)
1142 then the following macros need to be defined (examples are
1143 from include/configs/lwmon.h):
1147 (Optional). Any commands necessary to enable the I2C
1148 controller or configure ports.
1150 eg: #define I2C_INIT (immr->im_cpm.cp_pbdir |= PB_SCL)
1154 (Only for MPC8260 CPU). The I/O port to use (the code
1155 assumes both bits are on the same port). Valid values
1156 are 0..3 for ports A..D.
1160 The code necessary to make the I2C data line active
1161 (driven). If the data line is open collector, this
1164 eg: #define I2C_ACTIVE (immr->im_cpm.cp_pbdir |= PB_SDA)
1168 The code necessary to make the I2C data line tri-stated
1169 (inactive). If the data line is open collector, this
1172 eg: #define I2C_TRISTATE (immr->im_cpm.cp_pbdir &= ~PB_SDA)
1176 Code that returns TRUE if the I2C data line is high,
1179 eg: #define I2C_READ ((immr->im_cpm.cp_pbdat & PB_SDA) != 0)
1183 If <bit> is TRUE, sets the I2C data line high. If it
1184 is FALSE, it clears it (low).
1186 eg: #define I2C_SDA(bit) \
1187 if(bit) immr->im_cpm.cp_pbdat |= PB_SDA; \
1188 else immr->im_cpm.cp_pbdat &= ~PB_SDA
1192 If <bit> is TRUE, sets the I2C clock line high. If it
1193 is FALSE, it clears it (low).
1195 eg: #define I2C_SCL(bit) \
1196 if(bit) immr->im_cpm.cp_pbdat |= PB_SCL; \
1197 else immr->im_cpm.cp_pbdat &= ~PB_SCL
1201 This delay is invoked four times per clock cycle so this
1202 controls the rate of data transfer. The data rate thus
1203 is 1 / (I2C_DELAY * 4). Often defined to be something
1206 #define I2C_DELAY udelay(2)
1210 When a board is reset during an i2c bus transfer
1211 chips might think that the current transfer is still
1212 in progress. On some boards it is possible to access
1213 the i2c SCLK line directly, either by using the
1214 processor pin as a GPIO or by having a second pin
1215 connected to the bus. If this option is defined a
1216 custom i2c_init_board() routine in boards/xxx/board.c
1217 is run early in the boot sequence.
1219 CONFIG_I2CFAST (PPC405GP|PPC405EP only)
1221 This option enables configuration of bi_iic_fast[] flags
1222 in u-boot bd_info structure based on u-boot environment
1223 variable "i2cfast". (see also i2cfast)
1225 - SPI Support: CONFIG_SPI
1227 Enables SPI driver (so far only tested with
1228 SPI EEPROM, also an instance works with Crystal A/D and
1229 D/As on the SACSng board)
1233 Enables extended (16-bit) SPI EEPROM addressing.
1234 (symmetrical to CONFIG_I2C_X)
1238 Enables a software (bit-bang) SPI driver rather than
1239 using hardware support. This is a general purpose
1240 driver that only requires three general I/O port pins
1241 (two outputs, one input) to function. If this is
1242 defined, the board configuration must define several
1243 SPI configuration items (port pins to use, etc). For
1244 an example, see include/configs/sacsng.h.
1246 - FPGA Support: CONFIG_FPGA_COUNT
1248 Specify the number of FPGA devices to support.
1252 Used to specify the types of FPGA devices. For example,
1253 #define CONFIG_FPGA CFG_XILINX_VIRTEX2
1255 CFG_FPGA_PROG_FEEDBACK
1257 Enable printing of hash marks during FPGA configuration.
1261 Enable checks on FPGA configuration interface busy
1262 status by the configuration function. This option
1263 will require a board or device specific function to
1268 If defined, a function that provides delays in the FPGA
1269 configuration driver.
1271 CFG_FPGA_CHECK_CTRLC
1272 Allow Control-C to interrupt FPGA configuration
1274 CFG_FPGA_CHECK_ERROR
1276 Check for configuration errors during FPGA bitfile
1277 loading. For example, abort during Virtex II
1278 configuration if the INIT_B line goes low (which
1279 indicated a CRC error).
1283 Maximum time to wait for the INIT_B line to deassert
1284 after PROB_B has been deasserted during a Virtex II
1285 FPGA configuration sequence. The default time is 500
1290 Maximum time to wait for BUSY to deassert during
1291 Virtex II FPGA configuration. The default is 5 mS.
1293 CFG_FPGA_WAIT_CONFIG
1295 Time to wait after FPGA configuration. The default is
1298 - Configuration Management:
1301 If defined, this string will be added to the U-Boot
1302 version information (U_BOOT_VERSION)
1304 - Vendor Parameter Protection:
1306 U-Boot considers the values of the environment
1307 variables "serial#" (Board Serial Number) and
1308 "ethaddr" (Ethernet Address) to be parameters that
1309 are set once by the board vendor / manufacturer, and
1310 protects these variables from casual modification by
1311 the user. Once set, these variables are read-only,
1312 and write or delete attempts are rejected. You can
1313 change this behviour:
1315 If CONFIG_ENV_OVERWRITE is #defined in your config
1316 file, the write protection for vendor parameters is
1317 completely disabled. Anybody can change or delete
1320 Alternatively, if you #define _both_ CONFIG_ETHADDR
1321 _and_ CONFIG_OVERWRITE_ETHADDR_ONCE, a default
1322 ethernet address is installed in the environment,
1323 which can be changed exactly ONCE by the user. [The
1324 serial# is unaffected by this, i. e. it remains
1330 Define this variable to enable the reservation of
1331 "protected RAM", i. e. RAM which is not overwritten
1332 by U-Boot. Define CONFIG_PRAM to hold the number of
1333 kB you want to reserve for pRAM. You can overwrite
1334 this default value by defining an environment
1335 variable "pram" to the number of kB you want to
1336 reserve. Note that the board info structure will
1337 still show the full amount of RAM. If pRAM is
1338 reserved, a new environment variable "mem" will
1339 automatically be defined to hold the amount of
1340 remaining RAM in a form that can be passed as boot
1341 argument to Linux, for instance like that:
1343 setenv bootargs ... mem=\$(mem)
1346 This way you can tell Linux not to use this memory,
1347 either, which results in a memory region that will
1348 not be affected by reboots.
1350 *WARNING* If your board configuration uses automatic
1351 detection of the RAM size, you must make sure that
1352 this memory test is non-destructive. So far, the
1353 following board configurations are known to be
1356 ETX094, IVMS8, IVML24, SPD8xx, TQM8xxL,
1357 HERMES, IP860, RPXlite, LWMON, LANTEC,
1358 PCU_E, FLAGADM, TQM8260
1363 Define this variable to stop the system in case of a
1364 fatal error, so that you have to reset it manually.
1365 This is probably NOT a good idea for an embedded
1366 system where you want to system to reboot
1367 automatically as fast as possible, but it may be
1368 useful during development since you can try to debug
1369 the conditions that lead to the situation.
1371 CONFIG_NET_RETRY_COUNT
1373 This variable defines the number of retries for
1374 network operations like ARP, RARP, TFTP, or BOOTP
1375 before giving up the operation. If not defined, a
1376 default value of 5 is used.
1378 - Command Interpreter:
1381 Enable auto completion of commands using TAB.
1385 Define this variable to enable the "hush" shell (from
1386 Busybox) as command line interpreter, thus enabling
1387 powerful command line syntax like
1388 if...then...else...fi conditionals or `&&' and '||'
1389 constructs ("shell scripts").
1391 If undefined, you get the old, much simpler behaviour
1392 with a somewhat smaller memory footprint.
1397 This defines the secondary prompt string, which is
1398 printed when the command interpreter needs more input
1399 to complete a command. Usually "> ".
1403 In the current implementation, the local variables
1404 space and global environment variables space are
1405 separated. Local variables are those you define by
1406 simply typing `name=value'. To access a local
1407 variable later on, you have write `$name' or
1408 `${name}'; to execute the contents of a variable
1409 directly type `$name' at the command prompt.
1411 Global environment variables are those you use
1412 setenv/printenv to work with. To run a command stored
1413 in such a variable, you need to use the run command,
1414 and you must not use the '$' sign to access them.
1416 To store commands and special characters in a
1417 variable, please use double quotation marks
1418 surrounding the whole text of the variable, instead
1419 of the backslashes before semicolons and special
1422 - Default Environment:
1423 CONFIG_EXTRA_ENV_SETTINGS
1425 Define this to contain any number of null terminated
1426 strings (variable = value pairs) that will be part of
1427 the default environment compiled into the boot image.
1429 For example, place something like this in your
1430 board's config file:
1432 #define CONFIG_EXTRA_ENV_SETTINGS \
1436 Warning: This method is based on knowledge about the
1437 internal format how the environment is stored by the
1438 U-Boot code. This is NOT an official, exported
1439 interface! Although it is unlikely that this format
1440 will change soon, there is no guarantee either.
1441 You better know what you are doing here.
1443 Note: overly (ab)use of the default environment is
1444 discouraged. Make sure to check other ways to preset
1445 the environment like the autoscript function or the
1448 - DataFlash Support:
1449 CONFIG_HAS_DATAFLASH
1451 Defining this option enables DataFlash features and
1452 allows to read/write in Dataflash via the standard
1455 - SystemACE Support:
1458 Adding this option adds support for Xilinx SystemACE
1459 chips attached via some sort of local bus. The address
1460 of the chip must alsh be defined in the
1461 CFG_SYSTEMACE_BASE macro. For example:
1463 #define CONFIG_SYSTEMACE
1464 #define CFG_SYSTEMACE_BASE 0xf0000000
1466 When SystemACE support is added, the "ace" device type
1467 becomes available to the fat commands, i.e. fatls.
1469 - Show boot progress:
1470 CONFIG_SHOW_BOOT_PROGRESS
1472 Defining this option allows to add some board-
1473 specific code (calling a user-provided function
1474 "show_boot_progress(int)") that enables you to show
1475 the system's boot progress on some display (for
1476 example, some LED's) on your board. At the moment,
1477 the following checkpoints are implemented:
1480 1 common/cmd_bootm.c before attempting to boot an image
1481 -1 common/cmd_bootm.c Image header has bad magic number
1482 2 common/cmd_bootm.c Image header has correct magic number
1483 -2 common/cmd_bootm.c Image header has bad checksum
1484 3 common/cmd_bootm.c Image header has correct checksum
1485 -3 common/cmd_bootm.c Image data has bad checksum
1486 4 common/cmd_bootm.c Image data has correct checksum
1487 -4 common/cmd_bootm.c Image is for unsupported architecture
1488 5 common/cmd_bootm.c Architecture check OK
1489 -5 common/cmd_bootm.c Wrong Image Type (not kernel, multi, standalone)
1490 6 common/cmd_bootm.c Image Type check OK
1491 -6 common/cmd_bootm.c gunzip uncompression error
1492 -7 common/cmd_bootm.c Unimplemented compression type
1493 7 common/cmd_bootm.c Uncompression OK
1494 -8 common/cmd_bootm.c Wrong Image Type (not kernel, multi, standalone)
1495 8 common/cmd_bootm.c Image Type check OK
1496 -9 common/cmd_bootm.c Unsupported OS (not Linux, BSD, VxWorks, QNX)
1497 9 common/cmd_bootm.c Start initial ramdisk verification
1498 -10 common/cmd_bootm.c Ramdisk header has bad magic number
1499 -11 common/cmd_bootm.c Ramdisk header has bad checksum
1500 10 common/cmd_bootm.c Ramdisk header is OK
1501 -12 common/cmd_bootm.c Ramdisk data has bad checksum
1502 11 common/cmd_bootm.c Ramdisk data has correct checksum
1503 12 common/cmd_bootm.c Ramdisk verification complete, start loading
1504 -13 common/cmd_bootm.c Wrong Image Type (not PPC Linux Ramdisk)
1505 13 common/cmd_bootm.c Start multifile image verification
1506 14 common/cmd_bootm.c No initial ramdisk, no multifile, continue.
1507 15 common/cmd_bootm.c All preparation done, transferring control to OS
1509 -30 lib_ppc/board.c Fatal error, hang the system
1510 -31 post/post.c POST test failed, detected by post_output_backlog()
1511 -32 post/post.c POST test failed, detected by post_run_single()
1513 -1 common/cmd_doc.c Bad usage of "doc" command
1514 -1 common/cmd_doc.c No boot device
1515 -1 common/cmd_doc.c Unknown Chip ID on boot device
1516 -1 common/cmd_doc.c Read Error on boot device
1517 -1 common/cmd_doc.c Image header has bad magic number
1519 -1 common/cmd_ide.c Bad usage of "ide" command
1520 -1 common/cmd_ide.c No boot device
1521 -1 common/cmd_ide.c Unknown boot device
1522 -1 common/cmd_ide.c Unknown partition table
1523 -1 common/cmd_ide.c Invalid partition type
1524 -1 common/cmd_ide.c Read Error on boot device
1525 -1 common/cmd_ide.c Image header has bad magic number
1527 -1 common/cmd_nand.c Bad usage of "nand" command
1528 -1 common/cmd_nand.c No boot device
1529 -1 common/cmd_nand.c Unknown Chip ID on boot device
1530 -1 common/cmd_nand.c Read Error on boot device
1531 -1 common/cmd_nand.c Image header has bad magic number
1533 -1 common/env_common.c Environment has a bad CRC, using default
1539 [so far only for SMDK2400 and TRAB boards]
1541 - Modem support endable:
1542 CONFIG_MODEM_SUPPORT
1544 - RTS/CTS Flow control enable:
1547 - Modem debug support:
1548 CONFIG_MODEM_SUPPORT_DEBUG
1550 Enables debugging stuff (char screen[1024], dbg())
1551 for modem support. Useful only with BDI2000.
1553 - Interrupt support (PPC):
1555 There are common interrupt_init() and timer_interrupt()
1556 for all PPC archs. interrupt_init() calls interrupt_init_cpu()
1557 for cpu specific initialization. interrupt_init_cpu()
1558 should set decrementer_count to appropriate value. If
1559 cpu resets decrementer automatically after interrupt
1560 (ppc4xx) it should set decrementer_count to zero.
1561 timer_interrupt() calls timer_interrupt_cpu() for cpu
1562 specific handling. If board has watchdog / status_led
1563 / other_activity_monitor it works automatically from
1564 general timer_interrupt().
1568 In the target system modem support is enabled when a
1569 specific key (key combination) is pressed during
1570 power-on. Otherwise U-Boot will boot normally
1571 (autoboot). The key_pressed() fuction is called from
1572 board_init(). Currently key_pressed() is a dummy
1573 function, returning 1 and thus enabling modem
1576 If there are no modem init strings in the
1577 environment, U-Boot proceed to autoboot; the
1578 previous output (banner, info printfs) will be
1581 See also: doc/README.Modem
1584 Configuration Settings:
1585 -----------------------
1587 - CFG_LONGHELP: Defined when you want long help messages included;
1588 undefine this when you're short of memory.
1590 - CFG_PROMPT: This is what U-Boot prints on the console to
1591 prompt for user input.
1593 - CFG_CBSIZE: Buffer size for input from the Console
1595 - CFG_PBSIZE: Buffer size for Console output
1597 - CFG_MAXARGS: max. Number of arguments accepted for monitor commands
1599 - CFG_BARGSIZE: Buffer size for Boot Arguments which are passed to
1600 the application (usually a Linux kernel) when it is
1603 - CFG_BAUDRATE_TABLE:
1604 List of legal baudrate settings for this board.
1606 - CFG_CONSOLE_INFO_QUIET
1607 Suppress display of console information at boot.
1609 - CFG_CONSOLE_IS_IN_ENV
1610 If the board specific function
1611 extern int overwrite_console (void);
1612 returns 1, the stdin, stderr and stdout are switched to the
1613 serial port, else the settings in the environment are used.
1615 - CFG_CONSOLE_OVERWRITE_ROUTINE
1616 Enable the call to overwrite_console().
1618 - CFG_CONSOLE_ENV_OVERWRITE
1619 Enable overwrite of previous console environment settings.
1621 - CFG_MEMTEST_START, CFG_MEMTEST_END:
1622 Begin and End addresses of the area used by the
1626 Enable an alternate, more extensive memory test.
1628 - CFG_MEMTEST_SCRATCH:
1629 Scratch address used by the alternate memory test
1630 You only need to set this if address zero isn't writeable
1632 - CFG_TFTP_LOADADDR:
1633 Default load address for network file downloads
1635 - CFG_LOADS_BAUD_CHANGE:
1636 Enable temporary baudrate change while serial download
1639 Physical start address of SDRAM. _Must_ be 0 here.
1642 Physical start address of Motherboard I/O (if using a
1646 Physical start address of Flash memory.
1649 Physical start address of boot monitor code (set by
1650 make config files to be same as the text base address
1651 (TEXT_BASE) used when linking) - same as
1652 CFG_FLASH_BASE when booting from flash.
1655 Size of memory reserved for monitor code, used to
1656 determine _at_compile_time_ (!) if the environment is
1657 embedded within the U-Boot image, or in a separate
1661 Size of DRAM reserved for malloc() use.
1664 Maximum size of memory mapped by the startup code of
1665 the Linux kernel; all data that must be processed by
1666 the Linux kernel (bd_info, boot arguments, eventually
1667 initrd image) must be put below this limit.
1669 - CFG_MAX_FLASH_BANKS:
1670 Max number of Flash memory banks
1672 - CFG_MAX_FLASH_SECT:
1673 Max number of sectors on a Flash chip
1675 - CFG_FLASH_ERASE_TOUT:
1676 Timeout for Flash erase operations (in ms)
1678 - CFG_FLASH_WRITE_TOUT:
1679 Timeout for Flash write operations (in ms)
1681 - CFG_FLASH_LOCK_TOUT
1682 Timeout for Flash set sector lock bit operation (in ms)
1684 - CFG_FLASH_UNLOCK_TOUT
1685 Timeout for Flash clear lock bits operation (in ms)
1687 - CFG_FLASH_PROTECTION
1688 If defined, hardware flash sectors protection is used
1689 instead of U-Boot software protection.
1691 - CFG_DIRECT_FLASH_TFTP:
1693 Enable TFTP transfers directly to flash memory;
1694 without this option such a download has to be
1695 performed in two steps: (1) download to RAM, and (2)
1696 copy from RAM to flash.
1698 The two-step approach is usually more reliable, since
1699 you can check if the download worked before you erase
1700 the flash, but in some situations (when sytem RAM is
1701 too limited to allow for a tempory copy of the
1702 downloaded image) this option may be very useful.
1705 Define if the flash driver uses extra elements in the
1706 common flash structure for storing flash geometry.
1708 - CFG_FLASH_CFI_DRIVER
1709 This option also enables the building of the cfi_flash driver
1710 in the drivers directory
1712 - CFG_RX_ETH_BUFFER:
1713 Defines the number of ethernet receive buffers. On some
1714 ethernet controllers it is recommended to set this value
1715 to 8 or even higher (EEPRO100 or 405 EMAC), since all
1716 buffers can be full shortly after enabling the interface
1717 on high ethernet traffic.
1718 Defaults to 4 if not defined.
1720 The following definitions that deal with the placement and management
1721 of environment data (variable area); in general, we support the
1722 following configurations:
1724 - CFG_ENV_IS_IN_FLASH:
1726 Define this if the environment is in flash memory.
1728 a) The environment occupies one whole flash sector, which is
1729 "embedded" in the text segment with the U-Boot code. This
1730 happens usually with "bottom boot sector" or "top boot
1731 sector" type flash chips, which have several smaller
1732 sectors at the start or the end. For instance, such a
1733 layout can have sector sizes of 8, 2x4, 16, Nx32 kB. In
1734 such a case you would place the environment in one of the
1735 4 kB sectors - with U-Boot code before and after it. With
1736 "top boot sector" type flash chips, you would put the
1737 environment in one of the last sectors, leaving a gap
1738 between U-Boot and the environment.
1742 Offset of environment data (variable area) to the
1743 beginning of flash memory; for instance, with bottom boot
1744 type flash chips the second sector can be used: the offset
1745 for this sector is given here.
1747 CFG_ENV_OFFSET is used relative to CFG_FLASH_BASE.
1751 This is just another way to specify the start address of
1752 the flash sector containing the environment (instead of
1755 - CFG_ENV_SECT_SIZE:
1757 Size of the sector containing the environment.
1760 b) Sometimes flash chips have few, equal sized, BIG sectors.
1761 In such a case you don't want to spend a whole sector for
1766 If you use this in combination with CFG_ENV_IS_IN_FLASH
1767 and CFG_ENV_SECT_SIZE, you can specify to use only a part
1768 of this flash sector for the environment. This saves
1769 memory for the RAM copy of the environment.
1771 It may also save flash memory if you decide to use this
1772 when your environment is "embedded" within U-Boot code,
1773 since then the remainder of the flash sector could be used
1774 for U-Boot code. It should be pointed out that this is
1775 STRONGLY DISCOURAGED from a robustness point of view:
1776 updating the environment in flash makes it always
1777 necessary to erase the WHOLE sector. If something goes
1778 wrong before the contents has been restored from a copy in
1779 RAM, your target system will be dead.
1781 - CFG_ENV_ADDR_REDUND
1784 These settings describe a second storage area used to hold
1785 a redundand copy of the environment data, so that there is
1786 a valid backup copy in case there is a power failure during
1787 a "saveenv" operation.
1789 BE CAREFUL! Any changes to the flash layout, and some changes to the
1790 source code will make it necessary to adapt <board>/u-boot.lds*
1794 - CFG_ENV_IS_IN_NVRAM:
1796 Define this if you have some non-volatile memory device
1797 (NVRAM, battery buffered SRAM) which you want to use for the
1803 These two #defines are used to determin the memory area you
1804 want to use for environment. It is assumed that this memory
1805 can just be read and written to, without any special
1808 BE CAREFUL! The first access to the environment happens quite early
1809 in U-Boot initalization (when we try to get the setting of for the
1810 console baudrate). You *MUST* have mappend your NVRAM area then, or
1813 Please note that even with NVRAM we still use a copy of the
1814 environment in RAM: we could work on NVRAM directly, but we want to
1815 keep settings there always unmodified except somebody uses "saveenv"
1816 to save the current settings.
1819 - CFG_ENV_IS_IN_EEPROM:
1821 Use this if you have an EEPROM or similar serial access
1822 device and a driver for it.
1827 These two #defines specify the offset and size of the
1828 environment area within the total memory of your EEPROM.
1830 - CFG_I2C_EEPROM_ADDR:
1831 If defined, specified the chip address of the EEPROM device.
1832 The default address is zero.
1834 - CFG_EEPROM_PAGE_WRITE_BITS:
1835 If defined, the number of bits used to address bytes in a
1836 single page in the EEPROM device. A 64 byte page, for example
1837 would require six bits.
1839 - CFG_EEPROM_PAGE_WRITE_DELAY_MS:
1840 If defined, the number of milliseconds to delay between
1841 page writes. The default is zero milliseconds.
1843 - CFG_I2C_EEPROM_ADDR_LEN:
1844 The length in bytes of the EEPROM memory array address. Note
1845 that this is NOT the chip address length!
1847 - CFG_I2C_EEPROM_ADDR_OVERFLOW:
1848 EEPROM chips that implement "address overflow" are ones
1849 like Catalyst 24WC04/08/16 which has 9/10/11 bits of
1850 address and the extra bits end up in the "chip address" bit
1851 slots. This makes a 24WC08 (1Kbyte) chip look like four 256
1854 Note that we consider the length of the address field to
1855 still be one byte because the extra address bits are hidden
1856 in the chip address.
1859 The size in bytes of the EEPROM device.
1862 - CFG_ENV_IS_IN_DATAFLASH:
1864 Define this if you have a DataFlash memory device which you
1865 want to use for the environment.
1871 These three #defines specify the offset and size of the
1872 environment area within the total memory of your DataFlash placed
1873 at the specified address.
1875 - CFG_ENV_IS_IN_NAND:
1877 Define this if you have a NAND device which you want to use
1878 for the environment.
1883 These two #defines specify the offset and size of the environment
1884 area within the first NAND device.
1886 - CFG_SPI_INIT_OFFSET
1888 Defines offset to the initial SPI buffer area in DPRAM. The
1889 area is used at an early stage (ROM part) if the environment
1890 is configured to reside in the SPI EEPROM: We need a 520 byte
1891 scratch DPRAM area. It is used between the two initialization
1892 calls (spi_init_f() and spi_init_r()). A value of 0xB00 seems
1893 to be a good choice since it makes it far enough from the
1894 start of the data area as well as from the stack pointer.
1896 Please note that the environment is read-only as long as the monitor
1897 has been relocated to RAM and a RAM copy of the environment has been
1898 created; also, when using EEPROM you will have to use getenv_r()
1899 until then to read environment variables.
1901 The environment is protected by a CRC32 checksum. Before the monitor
1902 is relocated into RAM, as a result of a bad CRC you will be working
1903 with the compiled-in default environment - *silently*!!! [This is
1904 necessary, because the first environment variable we need is the
1905 "baudrate" setting for the console - if we have a bad CRC, we don't
1906 have any device yet where we could complain.]
1908 Note: once the monitor has been relocated, then it will complain if
1909 the default environment is used; a new CRC is computed as soon as you
1910 use the "saveenv" command to store a valid environment.
1912 - CFG_FAULT_ECHO_LINK_DOWN:
1913 Echo the inverted Ethernet link state to the fault LED.
1915 Note: If this option is active, then CFG_FAULT_MII_ADDR
1916 also needs to be defined.
1918 - CFG_FAULT_MII_ADDR:
1919 MII address of the PHY to check for the Ethernet link state.
1921 - CFG_64BIT_VSPRINTF:
1922 Makes vsprintf (and all *printf functions) support printing
1923 of 64bit values by using the L quantifier
1925 - CFG_64BIT_STRTOUL:
1926 Adds simple_strtoull that returns a 64bit value
1928 Low Level (hardware related) configuration options:
1929 ---------------------------------------------------
1931 - CFG_CACHELINE_SIZE:
1932 Cache Line Size of the CPU.
1935 Default address of the IMMR after system reset.
1937 Needed on some 8260 systems (MPC8260ADS, PQ2FADS-ZU,
1938 and RPXsuper) to be able to adjust the position of
1939 the IMMR register after a reset.
1941 - Floppy Disk Support:
1942 CFG_FDC_DRIVE_NUMBER
1944 the default drive number (default value 0)
1948 defines the spacing between fdc chipset registers
1953 defines the offset of register from address. It
1954 depends on which part of the data bus is connected to
1955 the fdc chipset. (default value 0)
1957 If CFG_ISA_IO_STRIDE CFG_ISA_IO_OFFSET and
1958 CFG_FDC_DRIVE_NUMBER are undefined, they take their
1961 if CFG_FDC_HW_INIT is defined, then the function
1962 fdc_hw_init() is called at the beginning of the FDC
1963 setup. fdc_hw_init() must be provided by the board
1964 source code. It is used to make hardware dependant
1967 - CFG_IMMR: Physical address of the Internal Memory Mapped
1968 Register; DO NOT CHANGE! (11-4)
1969 [MPC8xx systems only]
1971 - CFG_INIT_RAM_ADDR:
1973 Start address of memory area that can be used for
1974 initial data and stack; please note that this must be
1975 writable memory that is working WITHOUT special
1976 initialization, i. e. you CANNOT use normal RAM which
1977 will become available only after programming the
1978 memory controller and running certain initialization
1981 U-Boot uses the following memory types:
1982 - MPC8xx and MPC8260: IMMR (internal memory of the CPU)
1983 - MPC824X: data cache
1984 - PPC4xx: data cache
1986 - CFG_GBL_DATA_OFFSET:
1988 Offset of the initial data structure in the memory
1989 area defined by CFG_INIT_RAM_ADDR. Usually
1990 CFG_GBL_DATA_OFFSET is chosen such that the initial
1991 data is located at the end of the available space
1992 (sometimes written as (CFG_INIT_RAM_END -
1993 CFG_INIT_DATA_SIZE), and the initial stack is just
1994 below that area (growing from (CFG_INIT_RAM_ADDR +
1995 CFG_GBL_DATA_OFFSET) downward.
1998 On the MPC824X (or other systems that use the data
1999 cache for initial memory) the address chosen for
2000 CFG_INIT_RAM_ADDR is basically arbitrary - it must
2001 point to an otherwise UNUSED address space between
2002 the top of RAM and the start of the PCI space.
2004 - CFG_SIUMCR: SIU Module Configuration (11-6)
2006 - CFG_SYPCR: System Protection Control (11-9)
2008 - CFG_TBSCR: Time Base Status and Control (11-26)
2010 - CFG_PISCR: Periodic Interrupt Status and Control (11-31)
2012 - CFG_PLPRCR: PLL, Low-Power, and Reset Control Register (15-30)
2014 - CFG_SCCR: System Clock and reset Control Register (15-27)
2016 - CFG_OR_TIMING_SDRAM:
2020 periodic timer for refresh
2022 - CFG_DER: Debug Event Register (37-47)
2024 - FLASH_BASE0_PRELIM, FLASH_BASE1_PRELIM, CFG_REMAP_OR_AM,
2025 CFG_PRELIM_OR_AM, CFG_OR_TIMING_FLASH, CFG_OR0_REMAP,
2026 CFG_OR0_PRELIM, CFG_BR0_PRELIM, CFG_OR1_REMAP, CFG_OR1_PRELIM,
2028 Memory Controller Definitions: BR0/1 and OR0/1 (FLASH)
2030 - SDRAM_BASE2_PRELIM, SDRAM_BASE3_PRELIM, SDRAM_MAX_SIZE,
2031 CFG_OR_TIMING_SDRAM, CFG_OR2_PRELIM, CFG_BR2_PRELIM,
2032 CFG_OR3_PRELIM, CFG_BR3_PRELIM:
2033 Memory Controller Definitions: BR2/3 and OR2/3 (SDRAM)
2035 - CFG_MAMR_PTA, CFG_MPTPR_2BK_4K, CFG_MPTPR_1BK_4K, CFG_MPTPR_2BK_8K,
2036 CFG_MPTPR_1BK_8K, CFG_MAMR_8COL, CFG_MAMR_9COL:
2037 Machine Mode Register and Memory Periodic Timer
2038 Prescaler definitions (SDRAM timing)
2040 - CFG_I2C_UCODE_PATCH, CFG_I2C_DPMEM_OFFSET [0x1FC0]:
2041 enable I2C microcode relocation patch (MPC8xx);
2042 define relocation offset in DPRAM [DSP2]
2044 - CFG_SPI_UCODE_PATCH, CFG_SPI_DPMEM_OFFSET [0x1FC0]:
2045 enable SPI microcode relocation patch (MPC8xx);
2046 define relocation offset in DPRAM [SCC4]
2049 Use OSCM clock mode on MBX8xx board. Be careful,
2050 wrong setting might damage your board. Read
2051 doc/README.MBX before setting this variable!
2053 - CFG_CPM_POST_WORD_ADDR: (MPC8xx, MPC8260 only)
2054 Offset of the bootmode word in DPRAM used by post
2055 (Power On Self Tests). This definition overrides
2056 #define'd default value in commproc.h resp.
2059 - CFG_PCI_SLV_MEM_LOCAL, CFG_PCI_SLV_MEM_BUS, CFG_PICMR0_MASK_ATTRIB,
2060 CFG_PCI_MSTR0_LOCAL, CFG_PCIMSK0_MASK, CFG_PCI_MSTR1_LOCAL,
2061 CFG_PCIMSK1_MASK, CFG_PCI_MSTR_MEM_LOCAL, CFG_PCI_MSTR_MEM_BUS,
2062 CFG_CPU_PCI_MEM_START, CFG_PCI_MSTR_MEM_SIZE, CFG_POCMR0_MASK_ATTRIB,
2063 CFG_PCI_MSTR_MEMIO_LOCAL, CFG_PCI_MSTR_MEMIO_BUS, CPU_PCI_MEMIO_START,
2064 CFG_PCI_MSTR_MEMIO_SIZE, CFG_POCMR1_MASK_ATTRIB, CFG_PCI_MSTR_IO_LOCAL,
2065 CFG_PCI_MSTR_IO_BUS, CFG_CPU_PCI_IO_START, CFG_PCI_MSTR_IO_SIZE,
2066 CFG_POCMR2_MASK_ATTRIB: (MPC826x only)
2067 Overrides the default PCI memory map in cpu/mpc8260/pci.c if set.
2069 - CONFIG_ETHER_ON_FEC[12]
2070 Define to enable FEC[12] on a 8xx series processor.
2072 - CONFIG_FEC[12]_PHY
2073 Define to the hardcoded PHY address which corresponds
2074 to the given FEC; i. e.
2075 #define CONFIG_FEC1_PHY 4
2076 means that the PHY with address 4 is connected to FEC1
2078 When set to -1, means to probe for first available.
2080 - CONFIG_FEC[12]_PHY_NORXERR
2081 The PHY does not have a RXERR line (RMII only).
2082 (so program the FEC to ignore it).
2085 Enable RMII mode for all FECs.
2086 Note that this is a global option, we can't
2087 have one FEC in standard MII mode and another in RMII mode.
2089 - CONFIG_CRC32_VERIFY
2090 Add a verify option to the crc32 command.
2093 => crc32 -v <address> <count> <crc32>
2095 Where address/count indicate a memory area
2096 and crc32 is the correct crc32 which the
2100 Add the "loopw" memory command. This only takes effect if
2101 the memory commands are activated globally (CFG_CMD_MEM).
2103 Building the Software:
2104 ======================
2106 Building U-Boot has been tested in native PPC environments (on a
2107 PowerBook G3 running LinuxPPC 2000) and in cross environments
2108 (running RedHat 6.x and 7.x Linux on x86, Solaris 2.6 on a SPARC, and
2111 If you are not using a native PPC environment, it is assumed that you
2112 have the GNU cross compiling tools available in your path and named
2113 with a prefix of "powerpc-linux-". If this is not the case, (e.g. if
2114 you are using Monta Vista's Hard Hat Linux CDK 1.2) you must change
2115 the definition of CROSS_COMPILE in Makefile. For HHL on a 4xx CPU,
2118 CROSS_COMPILE = ppc_4xx-
2121 U-Boot is intended to be simple to build. After installing the
2122 sources you must configure U-Boot for one specific board type. This
2127 where "NAME_config" is the name of one of the existing
2128 configurations; the following names are supported:
2130 ADCIOP_config FPS860L_config omap730p2_config
2131 ADS860_config GEN860T_config pcu_e_config
2132 AR405_config GENIETV_config PIP405_config
2133 at91rm9200dk_config GTH_config QS823_config
2134 CANBT_config hermes_config QS850_config
2135 cmi_mpc5xx_config hymod_config QS860T_config
2136 cogent_common_config IP860_config RPXlite_config
2137 cogent_mpc8260_config IVML24_config RPXlite_DW_config
2138 cogent_mpc8xx_config IVMS8_config RPXsuper_config
2139 CPCI405_config JSE_config rsdproto_config
2140 CPCIISER4_config LANTEC_config Sandpoint8240_config
2141 csb272_config lwmon_config sbc8260_config
2142 CU824_config MBX860T_config sbc8560_33_config
2143 DUET_ADS_config MBX_config sbc8560_66_config
2144 EBONY_config MPC8260ADS_config SM850_config
2145 ELPT860_config MPC8540ADS_config SPD823TS_config
2146 ESTEEM192E_config MPC8560ADS_config stxgp3_config
2147 ETX094_config NETVIA_config SXNI855T_config
2148 FADS823_config omap1510inn_config TQM823L_config
2149 FADS850SAR_config omap1610h2_config TQM850L_config
2150 FADS860T_config omap1610inn_config TQM855L_config
2151 FPS850L_config omap5912osk_config TQM860L_config
2155 Note: for some board special configuration names may exist; check if
2156 additional information is available from the board vendor; for
2157 instance, the TQM823L systems are available without (standard)
2158 or with LCD support. You can select such additional "features"
2159 when chosing the configuration, i. e.
2162 - will configure for a plain TQM823L, i. e. no LCD support
2164 make TQM823L_LCD_config
2165 - will configure for a TQM823L with U-Boot console on LCD
2170 Finally, type "make all", and you should get some working U-Boot
2171 images ready for download to / installation on your system:
2173 - "u-boot.bin" is a raw binary image
2174 - "u-boot" is an image in ELF binary format
2175 - "u-boot.srec" is in Motorola S-Record format
2178 Please be aware that the Makefiles assume you are using GNU make, so
2179 for instance on NetBSD you might need to use "gmake" instead of
2183 If the system board that you have is not listed, then you will need
2184 to port U-Boot to your hardware platform. To do this, follow these
2187 1. Add a new configuration option for your board to the toplevel
2188 "Makefile" and to the "MAKEALL" script, using the existing
2189 entries as examples. Note that here and at many other places
2190 boards and other names are listed in alphabetical sort order. Please
2192 2. Create a new directory to hold your board specific code. Add any
2193 files you need. In your board directory, you will need at least
2194 the "Makefile", a "<board>.c", "flash.c" and "u-boot.lds".
2195 3. Create a new configuration file "include/configs/<board>.h" for
2197 3. If you're porting U-Boot to a new CPU, then also create a new
2198 directory to hold your CPU specific code. Add any files you need.
2199 4. Run "make <board>_config" with your new name.
2200 5. Type "make", and you should get a working "u-boot.srec" file
2201 to be installed on your target system.
2202 6. Debug and solve any problems that might arise.
2203 [Of course, this last step is much harder than it sounds.]
2206 Testing of U-Boot Modifications, Ports to New Hardware, etc.:
2207 ==============================================================
2209 If you have modified U-Boot sources (for instance added a new board
2210 or support for new devices, a new CPU, etc.) you are expected to
2211 provide feedback to the other developers. The feedback normally takes
2212 the form of a "patch", i. e. a context diff against a certain (latest
2213 official or latest in CVS) version of U-Boot sources.
2215 But before you submit such a patch, please verify that your modifi-
2216 cation did not break existing code. At least make sure that *ALL* of
2217 the supported boards compile WITHOUT ANY compiler warnings. To do so,
2218 just run the "MAKEALL" script, which will configure and build U-Boot
2219 for ALL supported system. Be warned, this will take a while. You can
2220 select which (cross) compiler to use by passing a `CROSS_COMPILE'
2221 environment variable to the script, i. e. to use the cross tools from
2222 MontaVista's Hard Hat Linux you can type
2224 CROSS_COMPILE=ppc_8xx- MAKEALL
2226 or to build on a native PowerPC system you can type
2228 CROSS_COMPILE=' ' MAKEALL
2230 See also "U-Boot Porting Guide" below.
2233 Monitor Commands - Overview:
2234 ============================
2236 go - start application at address 'addr'
2237 run - run commands in an environment variable
2238 bootm - boot application image from memory
2239 bootp - boot image via network using BootP/TFTP protocol
2240 tftpboot- boot image via network using TFTP protocol
2241 and env variables "ipaddr" and "serverip"
2242 (and eventually "gatewayip")
2243 rarpboot- boot image via network using RARP/TFTP protocol
2244 diskboot- boot from IDE devicebootd - boot default, i.e., run 'bootcmd'
2245 loads - load S-Record file over serial line
2246 loadb - load binary file over serial line (kermit mode)
2248 mm - memory modify (auto-incrementing)
2249 nm - memory modify (constant address)
2250 mw - memory write (fill)
2252 cmp - memory compare
2253 crc32 - checksum calculation
2254 imd - i2c memory display
2255 imm - i2c memory modify (auto-incrementing)
2256 inm - i2c memory modify (constant address)
2257 imw - i2c memory write (fill)
2258 icrc32 - i2c checksum calculation
2259 iprobe - probe to discover valid I2C chip addresses
2260 iloop - infinite loop on address range
2261 isdram - print SDRAM configuration information
2262 sspi - SPI utility commands
2263 base - print or set address offset
2264 printenv- print environment variables
2265 setenv - set environment variables
2266 saveenv - save environment variables to persistent storage
2267 protect - enable or disable FLASH write protection
2268 erase - erase FLASH memory
2269 flinfo - print FLASH memory information
2270 bdinfo - print Board Info structure
2271 iminfo - print header information for application image
2272 coninfo - print console devices and informations
2273 ide - IDE sub-system
2274 loop - infinite loop on address range
2275 loopw - infinite write loop on address range
2276 mtest - simple RAM test
2277 icache - enable or disable instruction cache
2278 dcache - enable or disable data cache
2279 reset - Perform RESET of the CPU
2280 echo - echo args to console
2281 version - print monitor version
2282 help - print online help
2283 ? - alias for 'help'
2286 Monitor Commands - Detailed Description:
2287 ========================================
2291 For now: just type "help <command>".
2294 Environment Variables:
2295 ======================
2297 U-Boot supports user configuration using Environment Variables which
2298 can be made persistent by saving to Flash memory.
2300 Environment Variables are set using "setenv", printed using
2301 "printenv", and saved to Flash using "saveenv". Using "setenv"
2302 without a value can be used to delete a variable from the
2303 environment. As long as you don't save the environment you are
2304 working with an in-memory copy. In case the Flash area containing the
2305 environment is erased by accident, a default environment is provided.
2307 Some configuration options can be set using Environment Variables:
2309 baudrate - see CONFIG_BAUDRATE
2311 bootdelay - see CONFIG_BOOTDELAY
2313 bootcmd - see CONFIG_BOOTCOMMAND
2315 bootargs - Boot arguments when booting an RTOS image
2317 bootfile - Name of the image to load with TFTP
2319 autoload - if set to "no" (any string beginning with 'n'),
2320 "bootp" will just load perform a lookup of the
2321 configuration from the BOOTP server, but not try to
2322 load any image using TFTP
2324 autostart - if set to "yes", an image loaded using the "bootp",
2325 "rarpboot", "tftpboot" or "diskboot" commands will
2326 be automatically started (by internally calling
2329 If set to "no", a standalone image passed to the
2330 "bootm" command will be copied to the load address
2331 (and eventually uncompressed), but NOT be started.
2332 This can be used to load and uncompress arbitrary
2335 i2cfast - (PPC405GP|PPC405EP only)
2336 if set to 'y' configures Linux I2C driver for fast
2337 mode (400kHZ). This environment variable is used in
2338 initialization code. So, for changes to be effective
2339 it must be saved and board must be reset.
2341 initrd_high - restrict positioning of initrd images:
2342 If this variable is not set, initrd images will be
2343 copied to the highest possible address in RAM; this
2344 is usually what you want since it allows for
2345 maximum initrd size. If for some reason you want to
2346 make sure that the initrd image is loaded below the
2347 CFG_BOOTMAPSZ limit, you can set this environment
2348 variable to a value of "no" or "off" or "0".
2349 Alternatively, you can set it to a maximum upper
2350 address to use (U-Boot will still check that it
2351 does not overwrite the U-Boot stack and data).
2353 For instance, when you have a system with 16 MB
2354 RAM, and want to reserve 4 MB from use by Linux,
2355 you can do this by adding "mem=12M" to the value of
2356 the "bootargs" variable. However, now you must make
2357 sure that the initrd image is placed in the first
2358 12 MB as well - this can be done with
2360 setenv initrd_high 00c00000
2362 If you set initrd_high to 0xFFFFFFFF, this is an
2363 indication to U-Boot that all addresses are legal
2364 for the Linux kernel, including addresses in flash
2365 memory. In this case U-Boot will NOT COPY the
2366 ramdisk at all. This may be useful to reduce the
2367 boot time on your system, but requires that this
2368 feature is supported by your Linux kernel.
2370 ipaddr - IP address; needed for tftpboot command
2372 loadaddr - Default load address for commands like "bootp",
2373 "rarpboot", "tftpboot", "loadb" or "diskboot"
2375 loads_echo - see CONFIG_LOADS_ECHO
2377 serverip - TFTP server IP address; needed for tftpboot command
2379 bootretry - see CONFIG_BOOT_RETRY_TIME
2381 bootdelaykey - see CONFIG_AUTOBOOT_DELAY_STR
2383 bootstopkey - see CONFIG_AUTOBOOT_STOP_STR
2385 ethprime - When CONFIG_NET_MULTI is enabled controls which
2386 interface is used first.
2388 ethact - When CONFIG_NET_MULTI is enabled controls which
2389 interface is currently active. For example you
2390 can do the following
2392 => setenv ethact FEC ETHERNET
2393 => ping 192.168.0.1 # traffic sent on FEC ETHERNET
2394 => setenv ethact SCC ETHERNET
2395 => ping 10.0.0.1 # traffic sent on SCC ETHERNET
2397 netretry - When set to "no" each network operation will
2398 either succeed or fail without retrying.
2399 When set to "once" the network operation will
2400 fail when all the available network interfaces
2401 are tried once without success.
2402 Useful on scripts which control the retry operation
2405 vlan - When set to a value < 4095 the traffic over
2406 ethernet is encapsulated/received over 802.1q
2409 The following environment variables may be used and automatically
2410 updated by the network boot commands ("bootp" and "rarpboot"),
2411 depending the information provided by your boot server:
2413 bootfile - see above
2414 dnsip - IP address of your Domain Name Server
2415 dnsip2 - IP address of your secondary Domain Name Server
2416 gatewayip - IP address of the Gateway (Router) to use
2417 hostname - Target hostname
2419 netmask - Subnet Mask
2420 rootpath - Pathname of the root filesystem on the NFS server
2421 serverip - see above
2424 There are two special Environment Variables:
2426 serial# - contains hardware identification information such
2427 as type string and/or serial number
2428 ethaddr - Ethernet address
2430 These variables can be set only once (usually during manufacturing of
2431 the board). U-Boot refuses to delete or overwrite these variables
2432 once they have been set once.
2435 Further special Environment Variables:
2437 ver - Contains the U-Boot version string as printed
2438 with the "version" command. This variable is
2439 readonly (see CONFIG_VERSION_VARIABLE).
2442 Please note that changes to some configuration parameters may take
2443 only effect after the next boot (yes, that's just like Windoze :-).
2446 Command Line Parsing:
2447 =====================
2449 There are two different command line parsers available with U-Boot:
2450 the old "simple" one, and the much more powerful "hush" shell:
2452 Old, simple command line parser:
2453 --------------------------------
2455 - supports environment variables (through setenv / saveenv commands)
2456 - several commands on one line, separated by ';'
2457 - variable substitution using "... $(name) ..." syntax
2458 - special characters ('$', ';') can be escaped by prefixing with '\',
2460 setenv bootcmd bootm \$(address)
2461 - You can also escape text by enclosing in single apostrophes, for example:
2462 setenv addip 'setenv bootargs $bootargs ip=$ipaddr:$serverip:$gatewayip:$netmask:$hostname::off'
2467 - similar to Bourne shell, with control structures like
2468 if...then...else...fi, for...do...done; while...do...done,
2469 until...do...done, ...
2470 - supports environment ("global") variables (through setenv / saveenv
2471 commands) and local shell variables (through standard shell syntax
2472 "name=value"); only environment variables can be used with "run"
2478 (1) If a command line (or an environment variable executed by a "run"
2479 command) contains several commands separated by semicolon, and
2480 one of these commands fails, then the remaining commands will be
2483 (2) If you execute several variables with one call to run (i. e.
2484 calling run with a list af variables as arguments), any failing
2485 command will cause "run" to terminate, i. e. the remaining
2486 variables are not executed.
2488 Note for Redundant Ethernet Interfaces:
2489 =======================================
2491 Some boards come with redundant ethernet interfaces; U-Boot supports
2492 such configurations and is capable of automatic selection of a
2493 "working" interface when needed. MAC assignment works as follows:
2495 Network interfaces are numbered eth0, eth1, eth2, ... Corresponding
2496 MAC addresses can be stored in the environment as "ethaddr" (=>eth0),
2497 "eth1addr" (=>eth1), "eth2addr", ...
2499 If the network interface stores some valid MAC address (for instance
2500 in SROM), this is used as default address if there is NO correspon-
2501 ding setting in the environment; if the corresponding environment
2502 variable is set, this overrides the settings in the card; that means:
2504 o If the SROM has a valid MAC address, and there is no address in the
2505 environment, the SROM's address is used.
2507 o If there is no valid address in the SROM, and a definition in the
2508 environment exists, then the value from the environment variable is
2511 o If both the SROM and the environment contain a MAC address, and
2512 both addresses are the same, this MAC address is used.
2514 o If both the SROM and the environment contain a MAC address, and the
2515 addresses differ, the value from the environment is used and a
2518 o If neither SROM nor the environment contain a MAC address, an error
2525 The "boot" commands of this monitor operate on "image" files which
2526 can be basicly anything, preceeded by a special header; see the
2527 definitions in include/image.h for details; basicly, the header
2528 defines the following image properties:
2530 * Target Operating System (Provisions for OpenBSD, NetBSD, FreeBSD,
2531 4.4BSD, Linux, SVR4, Esix, Solaris, Irix, SCO, Dell, NCR, VxWorks,
2532 LynxOS, pSOS, QNX, RTEMS, ARTOS;
2533 Currently supported: Linux, NetBSD, VxWorks, QNX, RTEMS, ARTOS, LynxOS).
2534 * Target CPU Architecture (Provisions for Alpha, ARM, Intel x86,
2535 IA64, MIPS, NIOS, PowerPC, IBM S390, SuperH, Sparc, Sparc 64 Bit;
2536 Currently supported: ARM, Intel x86, MIPS, NIOS, PowerPC).
2537 * Compression Type (uncompressed, gzip, bzip2)
2543 The header is marked by a special Magic Number, and both the header
2544 and the data portions of the image are secured against corruption by
2551 Although U-Boot should support any OS or standalone application
2552 easily, the main focus has always been on Linux during the design of
2555 U-Boot includes many features that so far have been part of some
2556 special "boot loader" code within the Linux kernel. Also, any
2557 "initrd" images to be used are no longer part of one big Linux image;
2558 instead, kernel and "initrd" are separate images. This implementation
2559 serves several purposes:
2561 - the same features can be used for other OS or standalone
2562 applications (for instance: using compressed images to reduce the
2563 Flash memory footprint)
2565 - it becomes much easier to port new Linux kernel versions because
2566 lots of low-level, hardware dependent stuff are done by U-Boot
2568 - the same Linux kernel image can now be used with different "initrd"
2569 images; of course this also means that different kernel images can
2570 be run with the same "initrd". This makes testing easier (you don't
2571 have to build a new "zImage.initrd" Linux image when you just
2572 change a file in your "initrd"). Also, a field-upgrade of the
2573 software is easier now.
2579 Porting Linux to U-Boot based systems:
2580 ---------------------------------------
2582 U-Boot cannot save you from doing all the necessary modifications to
2583 configure the Linux device drivers for use with your target hardware
2584 (no, we don't intend to provide a full virtual machine interface to
2587 But now you can ignore ALL boot loader code (in arch/ppc/mbxboot).
2589 Just make sure your machine specific header file (for instance
2590 include/asm-ppc/tqm8xx.h) includes the same definition of the Board
2591 Information structure as we define in include/u-boot.h, and make
2592 sure that your definition of IMAP_ADDR uses the same value as your
2593 U-Boot configuration in CFG_IMMR.
2596 Configuring the Linux kernel:
2597 -----------------------------
2599 No specific requirements for U-Boot. Make sure you have some root
2600 device (initial ramdisk, NFS) for your target system.
2603 Building a Linux Image:
2604 -----------------------
2606 With U-Boot, "normal" build targets like "zImage" or "bzImage" are
2607 not used. If you use recent kernel source, a new build target
2608 "uImage" will exist which automatically builds an image usable by
2609 U-Boot. Most older kernels also have support for a "pImage" target,
2610 which was introduced for our predecessor project PPCBoot and uses a
2611 100% compatible format.
2620 The "uImage" build target uses a special tool (in 'tools/mkimage') to
2621 encapsulate a compressed Linux kernel image with header information,
2622 CRC32 checksum etc. for use with U-Boot. This is what we are doing:
2624 * build a standard "vmlinux" kernel image (in ELF binary format):
2626 * convert the kernel into a raw binary image:
2628 ${CROSS_COMPILE}-objcopy -O binary \
2629 -R .note -R .comment \
2630 -S vmlinux linux.bin
2632 * compress the binary image:
2636 * package compressed binary image for U-Boot:
2638 mkimage -A ppc -O linux -T kernel -C gzip \
2639 -a 0 -e 0 -n "Linux Kernel Image" \
2640 -d linux.bin.gz uImage
2643 The "mkimage" tool can also be used to create ramdisk images for use
2644 with U-Boot, either separated from the Linux kernel image, or
2645 combined into one file. "mkimage" encapsulates the images with a 64
2646 byte header containing information about target architecture,
2647 operating system, image type, compression method, entry points, time
2648 stamp, CRC32 checksums, etc.
2650 "mkimage" can be called in two ways: to verify existing images and
2651 print the header information, or to build new images.
2653 In the first form (with "-l" option) mkimage lists the information
2654 contained in the header of an existing U-Boot image; this includes
2655 checksum verification:
2657 tools/mkimage -l image
2658 -l ==> list image header information
2660 The second form (with "-d" option) is used to build a U-Boot image
2661 from a "data file" which is used as image payload:
2663 tools/mkimage -A arch -O os -T type -C comp -a addr -e ep \
2664 -n name -d data_file image
2665 -A ==> set architecture to 'arch'
2666 -O ==> set operating system to 'os'
2667 -T ==> set image type to 'type'
2668 -C ==> set compression type 'comp'
2669 -a ==> set load address to 'addr' (hex)
2670 -e ==> set entry point to 'ep' (hex)
2671 -n ==> set image name to 'name'
2672 -d ==> use image data from 'datafile'
2674 Right now, all Linux kernels for PowerPC systems use the same load
2675 address (0x00000000), but the entry point address depends on the
2678 - 2.2.x kernels have the entry point at 0x0000000C,
2679 - 2.3.x and later kernels have the entry point at 0x00000000.
2681 So a typical call to build a U-Boot image would read:
2683 -> tools/mkimage -n '2.4.4 kernel for TQM850L' \
2684 > -A ppc -O linux -T kernel -C gzip -a 0 -e 0 \
2685 > -d /opt/elsk/ppc_8xx/usr/src/linux-2.4.4/arch/ppc/coffboot/vmlinux.gz \
2686 > examples/uImage.TQM850L
2687 Image Name: 2.4.4 kernel for TQM850L
2688 Created: Wed Jul 19 02:34:59 2000
2689 Image Type: PowerPC Linux Kernel Image (gzip compressed)
2690 Data Size: 335725 Bytes = 327.86 kB = 0.32 MB
2691 Load Address: 0x00000000
2692 Entry Point: 0x00000000
2694 To verify the contents of the image (or check for corruption):
2696 -> tools/mkimage -l examples/uImage.TQM850L
2697 Image Name: 2.4.4 kernel for TQM850L
2698 Created: Wed Jul 19 02:34:59 2000
2699 Image Type: PowerPC Linux Kernel Image (gzip compressed)
2700 Data Size: 335725 Bytes = 327.86 kB = 0.32 MB
2701 Load Address: 0x00000000
2702 Entry Point: 0x00000000
2704 NOTE: for embedded systems where boot time is critical you can trade
2705 speed for memory and install an UNCOMPRESSED image instead: this
2706 needs more space in Flash, but boots much faster since it does not
2707 need to be uncompressed:
2709 -> gunzip /opt/elsk/ppc_8xx/usr/src/linux-2.4.4/arch/ppc/coffboot/vmlinux.gz
2710 -> tools/mkimage -n '2.4.4 kernel for TQM850L' \
2711 > -A ppc -O linux -T kernel -C none -a 0 -e 0 \
2712 > -d /opt/elsk/ppc_8xx/usr/src/linux-2.4.4/arch/ppc/coffboot/vmlinux \
2713 > examples/uImage.TQM850L-uncompressed
2714 Image Name: 2.4.4 kernel for TQM850L
2715 Created: Wed Jul 19 02:34:59 2000
2716 Image Type: PowerPC Linux Kernel Image (uncompressed)
2717 Data Size: 792160 Bytes = 773.59 kB = 0.76 MB
2718 Load Address: 0x00000000
2719 Entry Point: 0x00000000
2722 Similar you can build U-Boot images from a 'ramdisk.image.gz' file
2723 when your kernel is intended to use an initial ramdisk:
2725 -> tools/mkimage -n 'Simple Ramdisk Image' \
2726 > -A ppc -O linux -T ramdisk -C gzip \
2727 > -d /LinuxPPC/images/SIMPLE-ramdisk.image.gz examples/simple-initrd
2728 Image Name: Simple Ramdisk Image
2729 Created: Wed Jan 12 14:01:50 2000
2730 Image Type: PowerPC Linux RAMDisk Image (gzip compressed)
2731 Data Size: 566530 Bytes = 553.25 kB = 0.54 MB
2732 Load Address: 0x00000000
2733 Entry Point: 0x00000000
2736 Installing a Linux Image:
2737 -------------------------
2739 To downloading a U-Boot image over the serial (console) interface,
2740 you must convert the image to S-Record format:
2742 objcopy -I binary -O srec examples/image examples/image.srec
2744 The 'objcopy' does not understand the information in the U-Boot
2745 image header, so the resulting S-Record file will be relative to
2746 address 0x00000000. To load it to a given address, you need to
2747 specify the target address as 'offset' parameter with the 'loads'
2750 Example: install the image to address 0x40100000 (which on the
2751 TQM8xxL is in the first Flash bank):
2753 => erase 40100000 401FFFFF
2759 ## Ready for S-Record download ...
2760 ~>examples/image.srec
2761 1 2 3 4 5 6 7 8 9 10 11 12 13 ...
2763 15989 15990 15991 15992
2764 [file transfer complete]
2766 ## Start Addr = 0x00000000
2769 You can check the success of the download using the 'iminfo' command;
2770 this includes a checksum verification so you can be sure no data
2771 corruption happened:
2775 ## Checking Image at 40100000 ...
2776 Image Name: 2.2.13 for initrd on TQM850L
2777 Image Type: PowerPC Linux Kernel Image (gzip compressed)
2778 Data Size: 335725 Bytes = 327 kB = 0 MB
2779 Load Address: 00000000
2780 Entry Point: 0000000c
2781 Verifying Checksum ... OK
2787 The "bootm" command is used to boot an application that is stored in
2788 memory (RAM or Flash). In case of a Linux kernel image, the contents
2789 of the "bootargs" environment variable is passed to the kernel as
2790 parameters. You can check and modify this variable using the
2791 "printenv" and "setenv" commands:
2794 => printenv bootargs
2795 bootargs=root=/dev/ram
2797 => setenv bootargs root=/dev/nfs rw nfsroot=10.0.0.2:/LinuxPPC nfsaddrs=10.0.0.99:10.0.0.2
2799 => printenv bootargs
2800 bootargs=root=/dev/nfs rw nfsroot=10.0.0.2:/LinuxPPC nfsaddrs=10.0.0.99:10.0.0.2
2803 ## Booting Linux kernel at 40020000 ...
2804 Image Name: 2.2.13 for NFS on TQM850L
2805 Image Type: PowerPC Linux Kernel Image (gzip compressed)
2806 Data Size: 381681 Bytes = 372 kB = 0 MB
2807 Load Address: 00000000
2808 Entry Point: 0000000c
2809 Verifying Checksum ... OK
2810 Uncompressing Kernel Image ... OK
2811 Linux version 2.2.13 (wd@denx.local.net) (gcc version 2.95.2 19991024 (release)) #1 Wed Jul 19 02:35:17 MEST 2000
2812 Boot arguments: root=/dev/nfs rw nfsroot=10.0.0.2:/LinuxPPC nfsaddrs=10.0.0.99:10.0.0.2
2813 time_init: decrementer frequency = 187500000/60
2814 Calibrating delay loop... 49.77 BogoMIPS
2815 Memory: 15208k available (700k kernel code, 444k data, 32k init) [c0000000,c1000000]
2818 If you want to boot a Linux kernel with initial ram disk, you pass
2819 the memory addresses of both the kernel and the initrd image (PPBCOOT
2820 format!) to the "bootm" command:
2822 => imi 40100000 40200000
2824 ## Checking Image at 40100000 ...
2825 Image Name: 2.2.13 for initrd on TQM850L
2826 Image Type: PowerPC Linux Kernel Image (gzip compressed)
2827 Data Size: 335725 Bytes = 327 kB = 0 MB
2828 Load Address: 00000000
2829 Entry Point: 0000000c
2830 Verifying Checksum ... OK
2832 ## Checking Image at 40200000 ...
2833 Image Name: Simple Ramdisk Image
2834 Image Type: PowerPC Linux RAMDisk Image (gzip compressed)
2835 Data Size: 566530 Bytes = 553 kB = 0 MB
2836 Load Address: 00000000
2837 Entry Point: 00000000
2838 Verifying Checksum ... OK
2840 => bootm 40100000 40200000
2841 ## Booting Linux kernel at 40100000 ...
2842 Image Name: 2.2.13 for initrd on TQM850L
2843 Image Type: PowerPC Linux Kernel Image (gzip compressed)
2844 Data Size: 335725 Bytes = 327 kB = 0 MB
2845 Load Address: 00000000
2846 Entry Point: 0000000c
2847 Verifying Checksum ... OK
2848 Uncompressing Kernel Image ... OK
2849 ## Loading RAMDisk Image at 40200000 ...
2850 Image Name: Simple Ramdisk Image
2851 Image Type: PowerPC Linux RAMDisk Image (gzip compressed)
2852 Data Size: 566530 Bytes = 553 kB = 0 MB
2853 Load Address: 00000000
2854 Entry Point: 00000000
2855 Verifying Checksum ... OK
2856 Loading Ramdisk ... OK
2857 Linux version 2.2.13 (wd@denx.local.net) (gcc version 2.95.2 19991024 (release)) #1 Wed Jul 19 02:32:08 MEST 2000
2858 Boot arguments: root=/dev/ram
2859 time_init: decrementer frequency = 187500000/60
2860 Calibrating delay loop... 49.77 BogoMIPS
2862 RAMDISK: Compressed image found at block 0
2863 VFS: Mounted root (ext2 filesystem).
2867 More About U-Boot Image Types:
2868 ------------------------------
2870 U-Boot supports the following image types:
2872 "Standalone Programs" are directly runnable in the environment
2873 provided by U-Boot; it is expected that (if they behave
2874 well) you can continue to work in U-Boot after return from
2875 the Standalone Program.
2876 "OS Kernel Images" are usually images of some Embedded OS which
2877 will take over control completely. Usually these programs
2878 will install their own set of exception handlers, device
2879 drivers, set up the MMU, etc. - this means, that you cannot
2880 expect to re-enter U-Boot except by resetting the CPU.
2881 "RAMDisk Images" are more or less just data blocks, and their
2882 parameters (address, size) are passed to an OS kernel that is
2884 "Multi-File Images" contain several images, typically an OS
2885 (Linux) kernel image and one or more data images like
2886 RAMDisks. This construct is useful for instance when you want
2887 to boot over the network using BOOTP etc., where the boot
2888 server provides just a single image file, but you want to get
2889 for instance an OS kernel and a RAMDisk image.
2891 "Multi-File Images" start with a list of image sizes, each
2892 image size (in bytes) specified by an "uint32_t" in network
2893 byte order. This list is terminated by an "(uint32_t)0".
2894 Immediately after the terminating 0 follow the images, one by
2895 one, all aligned on "uint32_t" boundaries (size rounded up to
2896 a multiple of 4 bytes).
2898 "Firmware Images" are binary images containing firmware (like
2899 U-Boot or FPGA images) which usually will be programmed to
2902 "Script files" are command sequences that will be executed by
2903 U-Boot's command interpreter; this feature is especially
2904 useful when you configure U-Boot to use a real shell (hush)
2905 as command interpreter.
2911 One of the features of U-Boot is that you can dynamically load and
2912 run "standalone" applications, which can use some resources of
2913 U-Boot like console I/O functions or interrupt services.
2915 Two simple examples are included with the sources:
2920 'examples/hello_world.c' contains a small "Hello World" Demo
2921 application; it is automatically compiled when you build U-Boot.
2922 It's configured to run at address 0x00040004, so you can play with it
2926 ## Ready for S-Record download ...
2927 ~>examples/hello_world.srec
2928 1 2 3 4 5 6 7 8 9 10 11 ...
2929 [file transfer complete]
2931 ## Start Addr = 0x00040004
2933 => go 40004 Hello World! This is a test.
2934 ## Starting application at 0x00040004 ...
2945 Hit any key to exit ...
2947 ## Application terminated, rc = 0x0
2949 Another example, which demonstrates how to register a CPM interrupt
2950 handler with the U-Boot code, can be found in 'examples/timer.c'.
2951 Here, a CPM timer is set up to generate an interrupt every second.
2952 The interrupt service routine is trivial, just printing a '.'
2953 character, but this is just a demo program. The application can be
2954 controlled by the following keys:
2956 ? - print current values og the CPM Timer registers
2957 b - enable interrupts and start timer
2958 e - stop timer and disable interrupts
2959 q - quit application
2962 ## Ready for S-Record download ...
2963 ~>examples/timer.srec
2964 1 2 3 4 5 6 7 8 9 10 11 ...
2965 [file transfer complete]
2967 ## Start Addr = 0x00040004
2970 ## Starting application at 0x00040004 ...
2973 tgcr @ 0xfff00980, tmr @ 0xfff00990, trr @ 0xfff00994, tcr @ 0xfff00998, tcn @ 0xfff0099c, ter @ 0xfff009b0
2976 [q, b, e, ?] Set interval 1000000 us
2979 [q, b, e, ?] ........
2980 tgcr=0x1, tmr=0xff1c, trr=0x3d09, tcr=0x0, tcn=0xef6, ter=0x0
2983 tgcr=0x1, tmr=0xff1c, trr=0x3d09, tcr=0x0, tcn=0x2ad4, ter=0x0
2986 tgcr=0x1, tmr=0xff1c, trr=0x3d09, tcr=0x0, tcn=0x1efc, ter=0x0
2989 tgcr=0x1, tmr=0xff1c, trr=0x3d09, tcr=0x0, tcn=0x169d, ter=0x0
2991 [q, b, e, ?] ...Stopping timer
2993 [q, b, e, ?] ## Application terminated, rc = 0x0
2999 Over time, many people have reported problems when trying to use the
3000 "minicom" terminal emulation program for serial download. I (wd)
3001 consider minicom to be broken, and recommend not to use it. Under
3002 Unix, I recommend to use C-Kermit for general purpose use (and
3003 especially for kermit binary protocol download ("loadb" command), and
3004 use "cu" for S-Record download ("loads" command).
3006 Nevertheless, if you absolutely want to use it try adding this
3007 configuration to your "File transfer protocols" section:
3009 Name Program Name U/D FullScr IO-Red. Multi
3010 X kermit /usr/bin/kermit -i -l %l -s Y U Y N N
3011 Y kermit /usr/bin/kermit -i -l %l -r N D Y N N
3017 Starting at version 0.9.2, U-Boot supports NetBSD both as host
3018 (build U-Boot) and target system (boots NetBSD/mpc8xx).
3020 Building requires a cross environment; it is known to work on
3021 NetBSD/i386 with the cross-powerpc-netbsd-1.3 package (you will also
3022 need gmake since the Makefiles are not compatible with BSD make).
3023 Note that the cross-powerpc package does not install include files;
3024 attempting to build U-Boot will fail because <machine/ansi.h> is
3025 missing. This file has to be installed and patched manually:
3027 # cd /usr/pkg/cross/powerpc-netbsd/include
3029 # ln -s powerpc machine
3030 # cp /usr/src/sys/arch/powerpc/include/ansi.h powerpc/ansi.h
3031 # ${EDIT} powerpc/ansi.h ## must remove __va_list, _BSD_VA_LIST
3033 Native builds *don't* work due to incompatibilities between native
3034 and U-Boot include files.
3036 Booting assumes that (the first part of) the image booted is a
3037 stage-2 loader which in turn loads and then invokes the kernel
3038 proper. Loader sources will eventually appear in the NetBSD source
3039 tree (probably in sys/arc/mpc8xx/stand/u-boot_stage2/); in the
3040 meantime, send mail to bruno@exet-ag.de and/or wd@denx.de for
3044 Implementation Internals:
3045 =========================
3047 The following is not intended to be a complete description of every
3048 implementation detail. However, it should help to understand the
3049 inner workings of U-Boot and make it easier to port it to custom
3053 Initial Stack, Global Data:
3054 ---------------------------
3056 The implementation of U-Boot is complicated by the fact that U-Boot
3057 starts running out of ROM (flash memory), usually without access to
3058 system RAM (because the memory controller is not initialized yet).
3059 This means that we don't have writable Data or BSS segments, and BSS
3060 is not initialized as zero. To be able to get a C environment working
3061 at all, we have to allocate at least a minimal stack. Implementation
3062 options for this are defined and restricted by the CPU used: Some CPU
3063 models provide on-chip memory (like the IMMR area on MPC8xx and
3064 MPC826x processors), on others (parts of) the data cache can be
3065 locked as (mis-) used as memory, etc.
3067 Chris Hallinan posted a good summary of these issues to the
3068 u-boot-users mailing list:
3070 Subject: RE: [U-Boot-Users] RE: More On Memory Bank x (nothingness)?
3071 From: "Chris Hallinan" <clh@net1plus.com>
3072 Date: Mon, 10 Feb 2003 16:43:46 -0500 (22:43 MET)
3075 Correct me if I'm wrong, folks, but the way I understand it
3076 is this: Using DCACHE as initial RAM for Stack, etc, does not
3077 require any physical RAM backing up the cache. The cleverness
3078 is that the cache is being used as a temporary supply of
3079 necessary storage before the SDRAM controller is setup. It's
3080 beyond the scope of this list to expain the details, but you
3081 can see how this works by studying the cache architecture and
3082 operation in the architecture and processor-specific manuals.
3084 OCM is On Chip Memory, which I believe the 405GP has 4K. It
3085 is another option for the system designer to use as an
3086 initial stack/ram area prior to SDRAM being available. Either
3087 option should work for you. Using CS 4 should be fine if your
3088 board designers haven't used it for something that would
3089 cause you grief during the initial boot! It is frequently not
3092 CFG_INIT_RAM_ADDR should be somewhere that won't interfere
3093 with your processor/board/system design. The default value
3094 you will find in any recent u-boot distribution in
3095 Walnut405.h should work for you. I'd set it to a value larger
3096 than your SDRAM module. If you have a 64MB SDRAM module, set
3097 it above 400_0000. Just make sure your board has no resources
3098 that are supposed to respond to that address! That code in
3099 start.S has been around a while and should work as is when
3100 you get the config right.
3105 It is essential to remember this, since it has some impact on the C
3106 code for the initialization procedures:
3108 * Initialized global data (data segment) is read-only. Do not attempt
3111 * Do not use any unitialized global data (or implicitely initialized
3112 as zero data - BSS segment) at all - this is undefined, initiali-
3113 zation is performed later (when relocating to RAM).
3115 * Stack space is very limited. Avoid big data buffers or things like
3118 Having only the stack as writable memory limits means we cannot use
3119 normal global data to share information beween the code. But it
3120 turned out that the implementation of U-Boot can be greatly
3121 simplified by making a global data structure (gd_t) available to all
3122 functions. We could pass a pointer to this data as argument to _all_
3123 functions, but this would bloat the code. Instead we use a feature of
3124 the GCC compiler (Global Register Variables) to share the data: we
3125 place a pointer (gd) to the global data into a register which we
3126 reserve for this purpose.
3128 When choosing a register for such a purpose we are restricted by the
3129 relevant (E)ABI specifications for the current architecture, and by
3130 GCC's implementation.
3132 For PowerPC, the following registers have specific use:
3135 R3-R4: parameter passing and return values
3136 R5-R10: parameter passing
3137 R13: small data area pointer
3141 (U-Boot also uses R14 as internal GOT pointer.)
3143 ==> U-Boot will use R29 to hold a pointer to the global data
3145 Note: on PPC, we could use a static initializer (since the
3146 address of the global data structure is known at compile time),
3147 but it turned out that reserving a register results in somewhat
3148 smaller code - although the code savings are not that big (on
3149 average for all boards 752 bytes for the whole U-Boot image,
3150 624 text + 127 data).
3152 On ARM, the following registers are used:
3154 R0: function argument word/integer result
3155 R1-R3: function argument word
3157 R10: stack limit (used only if stack checking if enabled)
3158 R11: argument (frame) pointer
3159 R12: temporary workspace
3162 R15: program counter
3164 ==> U-Boot will use R8 to hold a pointer to the global data
3170 U-Boot runs in system state and uses physical addresses, i.e. the
3171 MMU is not used either for address mapping nor for memory protection.
3173 The available memory is mapped to fixed addresses using the memory
3174 controller. In this process, a contiguous block is formed for each
3175 memory type (Flash, SDRAM, SRAM), even when it consists of several
3176 physical memory banks.
3178 U-Boot is installed in the first 128 kB of the first Flash bank (on
3179 TQM8xxL modules this is the range 0x40000000 ... 0x4001FFFF). After
3180 booting and sizing and initializing DRAM, the code relocates itself
3181 to the upper end of DRAM. Immediately below the U-Boot code some
3182 memory is reserved for use by malloc() [see CFG_MALLOC_LEN
3183 configuration setting]. Below that, a structure with global Board
3184 Info data is placed, followed by the stack (growing downward).
3186 Additionally, some exception handler code is copied to the low 8 kB
3187 of DRAM (0x00000000 ... 0x00001FFF).
3189 So a typical memory configuration with 16 MB of DRAM could look like
3192 0x0000 0000 Exception Vector code
3195 0x0000 2000 Free for Application Use
3201 0x00FB FF20 Monitor Stack (Growing downward)
3202 0x00FB FFAC Board Info Data and permanent copy of global data
3203 0x00FC 0000 Malloc Arena
3206 0x00FE 0000 RAM Copy of Monitor Code
3207 ... eventually: LCD or video framebuffer
3208 ... eventually: pRAM (Protected RAM - unchanged by reset)
3209 0x00FF FFFF [End of RAM]
3212 System Initialization:
3213 ----------------------
3215 In the reset configuration, U-Boot starts at the reset entry point
3216 (on most PowerPC systens at address 0x00000100). Because of the reset
3217 configuration for CS0# this is a mirror of the onboard Flash memory.
3218 To be able to re-map memory U-Boot then jumps to its link address.
3219 To be able to implement the initialization code in C, a (small!)
3220 initial stack is set up in the internal Dual Ported RAM (in case CPUs
3221 which provide such a feature like MPC8xx or MPC8260), or in a locked
3222 part of the data cache. After that, U-Boot initializes the CPU core,
3223 the caches and the SIU.
3225 Next, all (potentially) available memory banks are mapped using a
3226 preliminary mapping. For example, we put them on 512 MB boundaries
3227 (multiples of 0x20000000: SDRAM on 0x00000000 and 0x20000000, Flash
3228 on 0x40000000 and 0x60000000, SRAM on 0x80000000). Then UPM A is
3229 programmed for SDRAM access. Using the temporary configuration, a
3230 simple memory test is run that determines the size of the SDRAM
3233 When there is more than one SDRAM bank, and the banks are of
3234 different size, the largest is mapped first. For equal size, the first
3235 bank (CS2#) is mapped first. The first mapping is always for address
3236 0x00000000, with any additional banks following immediately to create
3237 contiguous memory starting from 0.
3239 Then, the monitor installs itself at the upper end of the SDRAM area
3240 and allocates memory for use by malloc() and for the global Board
3241 Info data; also, the exception vector code is copied to the low RAM
3242 pages, and the final stack is set up.
3244 Only after this relocation will you have a "normal" C environment;
3245 until that you are restricted in several ways, mostly because you are
3246 running from ROM, and because the code will have to be relocated to a
3250 U-Boot Porting Guide:
3251 ----------------------
3253 [Based on messages by Jerry Van Baren in the U-Boot-Users mailing
3257 int main (int argc, char *argv[])
3259 sighandler_t no_more_time;
3261 signal (SIGALRM, no_more_time);
3262 alarm (PROJECT_DEADLINE - toSec (3 * WEEK));
3264 if (available_money > available_manpower) {
3265 pay consultant to port U-Boot;
3269 Download latest U-Boot source;
3271 Subscribe to u-boot-users mailing list;
3274 email ("Hi, I am new to U-Boot, how do I get started?");
3278 Read the README file in the top level directory;
3279 Read http://www.denx.de/twiki/bin/view/DULG/Manual ;
3280 Read the source, Luke;
3283 if (available_money > toLocalCurrency ($2500)) {
3286 Add a lot of aggravation and time;
3289 Create your own board support subdirectory;
3291 Create your own board config file;
3295 Add / modify source code;
3299 email ("Hi, I am having problems...");
3301 Send patch file to Wolfgang;
3306 void no_more_time (int sig)
3315 All contributions to U-Boot should conform to the Linux kernel
3316 coding style; see the file "Documentation/CodingStyle" in your Linux
3317 kernel source directory.
3319 Please note that U-Boot is implemented in C (and to some small parts
3320 in Assembler); no C++ is used, so please do not use C++ style
3321 comments (//) in your code.
3323 Please also stick to the following formatting rules:
3324 - remove any trailing white space
3325 - use TAB characters for indentation, not spaces
3326 - make sure NOT to use DOS '\r\n' line feeds
3327 - do not add more than 2 empty lines to source files
3328 - do not add trailing empty lines to source files
3330 Submissions which do not conform to the standards may be returned
3331 with a request to reformat the changes.
3337 Since the number of patches for U-Boot is growing, we need to
3338 establish some rules. Submissions which do not conform to these rules
3339 may be rejected, even when they contain important and valuable stuff.
3342 When you send a patch, please include the following information with
3345 * For bug fixes: a description of the bug and how your patch fixes
3346 this bug. Please try to include a way of demonstrating that the
3347 patch actually fixes something.
3349 * For new features: a description of the feature and your
3352 * A CHANGELOG entry as plaintext (separate from the patch)
3354 * For major contributions, your entry to the CREDITS file
3356 * When you add support for a new board, don't forget to add this
3357 board to the MAKEALL script, too.
3359 * If your patch adds new configuration options, don't forget to
3360 document these in the README file.
3362 * The patch itself. If you are accessing the CVS repository use "cvs
3363 update; cvs diff -puRN"; else, use "diff -purN OLD NEW". If your
3364 version of diff does not support these options, then get the latest
3365 version of GNU diff.
3367 The current directory when running this command shall be the top
3368 level directory of the U-Boot source tree, or it's parent directory
3369 (i. e. please make sure that your patch includes sufficient
3370 directory information for the affected files).
3372 We accept patches as plain text, MIME attachments or as uuencoded
3375 * If one logical set of modifications affects or creates several
3376 files, all these changes shall be submitted in a SINGLE patch file.
3378 * Changesets that contain different, unrelated modifications shall be
3379 submitted as SEPARATE patches, one patch per changeset.
3384 * Before sending the patch, run the MAKEALL script on your patched
3385 source tree and make sure that no errors or warnings are reported
3386 for any of the boards.
3388 * Keep your modifications to the necessary minimum: A patch
3389 containing several unrelated changes or arbitrary reformats will be
3390 returned with a request to re-formatting / split it.
3392 * If you modify existing code, make sure that your new code does not
3393 add to the memory footprint of the code ;-) Small is beautiful!
3394 When adding new features, these should compile conditionally only
3395 (using #ifdef), and the resulting code with the new feature
3396 disabled must not need more memory than the old code without your
projects / platform / kernel / u-boot.git / blob