2 # (C) Copyright 2000 - 2004
3 # Wolfgang Denk, DENX Software Engineering, wd@denx.de.
5 # See file CREDITS for list of people who contributed to this
8 # This program is free software; you can redistribute it and/or
9 # modify it under the terms of the GNU General Public License as
10 # published by the Free Software Foundation; either version 2 of
11 # the License, or (at your option) any later version.
13 # This program is distributed in the hope that it will be useful,
14 # but WITHOUT ANY WARRANTY; without even the implied warranty of
15 # MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the
16 # GNU General Public License for more details.
18 # You should have received a copy of the GNU General Public License
19 # along with this program; if not, write to the Free Software
20 # Foundation, Inc., 59 Temple Place, Suite 330, Boston,
27 This directory contains the source code for U-Boot, a boot loader for
28 Embedded boards based on PowerPC, ARM, MIPS and several other
29 processors, which can be installed in a boot ROM and used to
30 initialize and test the hardware or to download and run application
33 The development of U-Boot is closely related to Linux: some parts of
34 the source code originate in the Linux source tree, we have some
35 header files in common, and special provision has been made to
36 support booting of Linux images.
38 Some attention has been paid to make this software easily
39 configurable and extendable. For instance, all monitor commands are
40 implemented with the same call interface, so that it's very easy to
41 add new commands. Also, instead of permanently adding rarely used
42 code (for instance hardware test utilities) to the monitor, you can
43 load and run it dynamically.
49 In general, all boards for which a configuration option exists in the
50 Makefile have been tested to some extent and can be considered
51 "working". In fact, many of them are used in production systems.
53 In case of problems see the CHANGELOG and CREDITS files to find out
54 who contributed the specific port.
60 In case you have questions about, problems with or contributions for
61 U-Boot you should send a message to the U-Boot mailing list at
62 <u-boot-users@lists.sourceforge.net>. There is also an archive of
63 previous traffic on the mailing list - please search the archive
64 before asking FAQ's. Please see
65 http://lists.sourceforge.net/lists/listinfo/u-boot-users/
71 - start from 8xxrom sources
72 - create PPCBoot project (http://sourceforge.net/projects/ppcboot)
74 - make it easier to add custom boards
75 - make it possible to add other [PowerPC] CPUs
76 - extend functions, especially:
77 * Provide extended interface to Linux boot loader
80 * PCMCIA / CompactFLash / ATA disk / SCSI ... boot
81 - create ARMBoot project (http://sourceforge.net/projects/armboot)
82 - add other CPU families (starting with ARM)
83 - create U-Boot project (http://sourceforge.net/projects/u-boot)
89 The "official" name of this project is "Das U-Boot". The spelling
90 "U-Boot" shall be used in all written text (documentation, comments
91 in source files etc.). Example:
93 This is the README file for the U-Boot project.
95 File names etc. shall be based on the string "u-boot". Examples:
97 include/asm-ppc/u-boot.h
99 #include <asm/u-boot.h>
101 Variable names, preprocessor constants etc. shall be either based on
102 the string "u_boot" or on "U_BOOT". Example:
104 U_BOOT_VERSION u_boot_logo
105 IH_OS_U_BOOT u_boot_hush_start
111 U-Boot uses a 3 level version number containing a version, a
112 sub-version, and a patchlevel: "U-Boot-2.34.5" means version "2",
113 sub-version "34", and patchlevel "4".
115 The patchlevel is used to indicate certain stages of development
116 between released versions, i. e. officially released versions of
117 U-Boot will always have a patchlevel of "0".
123 - board Board dependent files
124 - common Misc architecture independent functions
125 - cpu CPU specific files
126 - 74xx_7xx Files specific to Freescale MPC74xx and 7xx CPUs
127 - arm720t Files specific to ARM 720 CPUs
128 - arm920t Files specific to ARM 920 CPUs
129 - imx Files specific to Freescale MC9328 i.MX CPUs
130 - s3c24x0 Files specific to Samsung S3C24X0 CPUs
131 - arm925t Files specific to ARM 925 CPUs
132 - arm926ejs Files specific to ARM 926 CPUs
133 - at91rm9200 Files specific to Atmel AT91RM9200 CPUs
134 - i386 Files specific to i386 CPUs
135 - ixp Files specific to Intel XScale IXP CPUs
136 - mcf52x2 Files specific to Freescale ColdFire MCF52x2 CPUs
137 - mips Files specific to MIPS CPUs
138 - mpc5xx Files specific to Freescale MPC5xx CPUs
139 - mpc5xxx Files specific to Freescale MPC5xxx CPUs
140 - mpc8xx Files specific to Freescale MPC8xx CPUs
141 - mpc8220 Files specific to Freescale MPC8220 CPUs
142 - mpc824x Files specific to Freescale MPC824x CPUs
143 - mpc8260 Files specific to Freescale MPC8260 CPUs
144 - mpc85xx Files specific to Freescale MPC85xx CPUs
145 - nios Files specific to Altera NIOS CPUs
146 - nios2 Files specific to Altera Nios-II CPUs
147 - ppc4xx Files specific to IBM PowerPC 4xx CPUs
148 - pxa Files specific to Intel XScale PXA CPUs
149 - s3c44b0 Files specific to Samsung S3C44B0 CPUs
150 - sa1100 Files specific to Intel StrongARM SA1100 CPUs
151 - disk Code for disk drive partition handling
152 - doc Documentation (don't expect too much)
153 - drivers Commonly used device drivers
154 - dtt Digital Thermometer and Thermostat drivers
155 - examples Example code for standalone applications, etc.
156 - include Header Files
157 - lib_arm Files generic to ARM architecture
158 - lib_generic Files generic to all architectures
159 - lib_i386 Files generic to i386 architecture
160 - lib_m68k Files generic to m68k architecture
161 - lib_mips Files generic to MIPS architecture
162 - lib_nios Files generic to NIOS architecture
163 - lib_ppc Files generic to PowerPC architecture
164 - net Networking code
165 - post Power On Self Test
166 - rtc Real Time Clock drivers
167 - tools Tools to build S-Record or U-Boot images, etc.
169 Software Configuration:
170 =======================
172 Configuration is usually done using C preprocessor defines; the
173 rationale behind that is to avoid dead code whenever possible.
175 There are two classes of configuration variables:
177 * Configuration _OPTIONS_:
178 These are selectable by the user and have names beginning with
181 * Configuration _SETTINGS_:
182 These depend on the hardware etc. and should not be meddled with if
183 you don't know what you're doing; they have names beginning with
186 Later we will add a configuration tool - probably similar to or even
187 identical to what's used for the Linux kernel. Right now, we have to
188 do the configuration by hand, which means creating some symbolic
189 links and editing some configuration files. We use the TQM8xxL boards
193 Selection of Processor Architecture and Board Type:
194 ---------------------------------------------------
196 For all supported boards there are ready-to-use default
197 configurations available; just type "make <board_name>_config".
199 Example: For a TQM823L module type:
204 For the Cogent platform, you need to specify the cpu type as well;
205 e.g. "make cogent_mpc8xx_config". And also configure the cogent
206 directory according to the instructions in cogent/README.
209 Configuration Options:
210 ----------------------
212 Configuration depends on the combination of board and CPU type; all
213 such information is kept in a configuration file
214 "include/configs/<board_name>.h".
216 Example: For a TQM823L module, all configuration settings are in
217 "include/configs/TQM823L.h".
220 Many of the options are named exactly as the corresponding Linux
221 kernel configuration options. The intention is to make it easier to
222 build a config tool - later.
225 The following options need to be configured:
227 - CPU Type: Define exactly one of
231 CONFIG_MPC823, CONFIG_MPC850, CONFIG_MPC855, CONFIG_MPC860
234 or CONFIG_MPC824X, CONFIG_MPC8260
249 MicroBlaze based CPUs:
250 ----------------------
254 ----------------------
258 - Board Type: Define exactly one of
260 PowerPC based boards:
261 ---------------------
263 CONFIG_ADCIOP CONFIG_GEN860T CONFIG_PCI405
264 CONFIG_ADS860 CONFIG_GENIETV CONFIG_PCIPPC2
265 CONFIG_AMX860 CONFIG_GTH CONFIG_PCIPPC6
266 CONFIG_AR405 CONFIG_gw8260 CONFIG_pcu_e
267 CONFIG_BAB7xx CONFIG_hermes CONFIG_PIP405
268 CONFIG_c2mon CONFIG_hymod CONFIG_PM826
269 CONFIG_CANBT CONFIG_IAD210 CONFIG_ppmc8260
270 CONFIG_CCM CONFIG_ICU862 CONFIG_QS823
271 CONFIG_CMI CONFIG_IP860 CONFIG_QS850
272 CONFIG_cogent_mpc8260 CONFIG_IPHASE4539 CONFIG_QS860T
273 CONFIG_cogent_mpc8xx CONFIG_IVML24 CONFIG_RBC823
274 CONFIG_CPCI405 CONFIG_IVML24_128 CONFIG_RPXClassic
275 CONFIG_CPCI4052 CONFIG_IVML24_256 CONFIG_RPXlite
276 CONFIG_CPCIISER4 CONFIG_IVMS8 CONFIG_RPXsuper
277 CONFIG_CPU86 CONFIG_IVMS8_128 CONFIG_rsdproto
278 CONFIG_CRAYL1 CONFIG_IVMS8_256 CONFIG_sacsng
279 CONFIG_CSB272 CONFIG_JSE CONFIG_Sandpoint8240
280 CONFIG_CU824 CONFIG_LANTEC CONFIG_Sandpoint8245
281 CONFIG_DASA_SIM CONFIG_lwmon CONFIG_sbc8260
282 CONFIG_DB64360 CONFIG_MBX CONFIG_sbc8560
283 CONFIG_DB64460 CONFIG_MBX860T CONFIG_SM850
284 CONFIG_DU405 CONFIG_MHPC CONFIG_SPD823TS
285 CONFIG_DUET_ADS CONFIG_MIP405 CONFIG_STXGP3
286 CONFIG_EBONY CONFIG_MOUSSE CONFIG_SXNI855T
287 CONFIG_ELPPC CONFIG_MPC8260ADS CONFIG_TQM823L
288 CONFIG_ELPT860 CONFIG_MPC8540ADS CONFIG_TQM8260
289 CONFIG_ep8260 CONFIG_MPC8560ADS CONFIG_TQM850L
290 CONFIG_ERIC CONFIG_MUSENKI CONFIG_TQM855L
291 CONFIG_ESTEEM192E CONFIG_MVS1 CONFIG_TQM860L
292 CONFIG_ETX094 CONFIG_NETPHONE CONFIG_TTTech
293 CONFIG_EVB64260 CONFIG_NETTA CONFIG_UTX8245
294 CONFIG_FADS823 CONFIG_NETVIA CONFIG_V37
295 CONFIG_FADS850SAR CONFIG_NX823 CONFIG_W7OLMC
296 CONFIG_FADS860T CONFIG_OCRTC CONFIG_W7OLMG
297 CONFIG_FLAGADM CONFIG_ORSG CONFIG_WALNUT405
298 CONFIG_FPS850L CONFIG_OXC CONFIG_ZPC1900
299 CONFIG_FPS860L CONFIG_ZUMA
304 CONFIG_AT91RM9200DK, CONFIG_CERF250, CONFIG_DNP1110,
305 CONFIG_EP7312, CONFIG_H2_OMAP1610, CONFIG_HHP_CRADLE,
306 CONFIG_IMPA7, CONFIG_INNOVATOROMAP1510, CONFIG_INNOVATOROMAP1610,
307 CONFIG_LART, CONFIG_LPD7A400 CONFIG_LUBBOCK,
308 CONFIG_OSK_OMAP5912, CONFIG_SHANNON, CONFIG_P2_OMAP730,
309 CONFIG_SMDK2400, CONFIG_SMDK2410, CONFIG_TRAB,
312 MicroBlaze based boards:
313 ------------------------
318 ------------------------
320 CONFIG_PCI5441 CONFIG_PK1C20
323 - CPU Module Type: (if CONFIG_COGENT is defined)
324 Define exactly one of
326 --- FIXME --- not tested yet:
327 CONFIG_CMA286_60, CONFIG_CMA286_21, CONFIG_CMA286_60P,
328 CONFIG_CMA287_23, CONFIG_CMA287_50
330 - Motherboard Type: (if CONFIG_COGENT is defined)
331 Define exactly one of
332 CONFIG_CMA101, CONFIG_CMA102
334 - Motherboard I/O Modules: (if CONFIG_COGENT is defined)
335 Define one or more of
338 - Motherboard Options: (if CONFIG_CMA101 or CONFIG_CMA102 are defined)
339 Define one or more of
340 CONFIG_LCD_HEARTBEAT - update a character position on
341 the lcd display every second with
344 - Board flavour: (if CONFIG_MPC8260ADS is defined)
347 CFG_8260ADS - original MPC8260ADS
348 CFG_8266ADS - MPC8266ADS
349 CFG_PQ2FADS - PQ2FADS-ZU or PQ2FADS-VR
350 CFG_8272ADS - MPC8272ADS
352 - MPC824X Family Member (if CONFIG_MPC824X is defined)
353 Define exactly one of
354 CONFIG_MPC8240, CONFIG_MPC8245
356 - 8xx CPU Options: (if using an MPC8xx cpu)
357 CONFIG_8xx_GCLK_FREQ - deprecated: CPU clock if
358 get_gclk_freq() cannot work
359 e.g. if there is no 32KHz
360 reference PIT/RTC clock
361 CONFIG_8xx_OSCLK - PLL input clock (either EXTCLK
364 - 859/866/885 CPU options: (if using a MPC859 or MPC866 or MPC885 CPU):
367 CONFIG_8xx_CPUCLK_DEFAULT
368 See doc/README.MPC866
372 Define this to measure the actual CPU clock instead
373 of relying on the correctness of the configured
374 values. Mostly useful for board bringup to make sure
375 the PLL is locked at the intended frequency. Note
376 that this requires a (stable) reference clock (32 kHz
377 RTC clock or CFG_8XX_XIN)
379 - Linux Kernel Interface:
382 U-Boot stores all clock information in Hz
383 internally. For binary compatibility with older Linux
384 kernels (which expect the clocks passed in the
385 bd_info data to be in MHz) the environment variable
386 "clocks_in_mhz" can be defined so that U-Boot
387 converts clock data to MHZ before passing it to the
389 When CONFIG_CLOCKS_IN_MHZ is defined, a definition of
390 "clocks_in_mhz=1" is automatically included in the
393 CONFIG_MEMSIZE_IN_BYTES [relevant for MIPS only]
395 When transfering memsize parameter to linux, some versions
396 expect it to be in bytes, others in MB.
397 Define CONFIG_MEMSIZE_IN_BYTES to make it in bytes.
402 Define this if you want support for Amba PrimeCell PL010 UARTs.
406 Define this if you want support for Amba PrimeCell PL011 UARTs.
410 If you have Amba PrimeCell PL011 UARTs, set this variable to
411 the clock speed of the UARTs.
415 If you have Amba PrimeCell PL010 or PL011 UARTs on your board,
416 define this to a list of base addresses for each (supported)
417 port. See e.g. include/configs/versatile.h
421 Depending on board, define exactly one serial port
422 (like CONFIG_8xx_CONS_SMC1, CONFIG_8xx_CONS_SMC2,
423 CONFIG_8xx_CONS_SCC1, ...), or switch off the serial
424 console by defining CONFIG_8xx_CONS_NONE
426 Note: if CONFIG_8xx_CONS_NONE is defined, the serial
427 port routines must be defined elsewhere
428 (i.e. serial_init(), serial_getc(), ...)
431 Enables console device for a color framebuffer. Needs following
432 defines (cf. smiLynxEM, i8042, board/eltec/bab7xx)
433 VIDEO_FB_LITTLE_ENDIAN graphic memory organisation
435 VIDEO_HW_RECTFILL graphic chip supports
438 VIDEO_HW_BITBLT graphic chip supports
439 bit-blit (cf. smiLynxEM)
440 VIDEO_VISIBLE_COLS visible pixel columns
442 VIDEO_VISIBLE_ROWS visible pixel rows
443 VIDEO_PIXEL_SIZE bytes per pixel
444 VIDEO_DATA_FORMAT graphic data format
445 (0-5, cf. cfb_console.c)
446 VIDEO_FB_ADRS framebuffer address
447 VIDEO_KBD_INIT_FCT keyboard int fct
448 (i.e. i8042_kbd_init())
449 VIDEO_TSTC_FCT test char fct
451 VIDEO_GETC_FCT get char fct
453 CONFIG_CONSOLE_CURSOR cursor drawing on/off
454 (requires blink timer
456 CFG_CONSOLE_BLINK_COUNT blink interval (cf. i8042.c)
457 CONFIG_CONSOLE_TIME display time/date info in
459 (requires CFG_CMD_DATE)
460 CONFIG_VIDEO_LOGO display Linux logo in
462 CONFIG_VIDEO_BMP_LOGO use bmp_logo.h instead of
463 linux_logo.h for logo.
464 Requires CONFIG_VIDEO_LOGO
465 CONFIG_CONSOLE_EXTRA_INFO
466 addional board info beside
469 When CONFIG_CFB_CONSOLE is defined, video console is
470 default i/o. Serial console can be forced with
471 environment 'console=serial'.
473 When CONFIG_SILENT_CONSOLE is defined, all console
474 messages (by U-Boot and Linux!) can be silenced with
475 the "silent" environment variable. See
476 doc/README.silent for more information.
479 CONFIG_BAUDRATE - in bps
480 Select one of the baudrates listed in
481 CFG_BAUDRATE_TABLE, see below.
482 CFG_BRGCLK_PRESCALE, baudrate prescale
484 - Interrupt driven serial port input:
485 CONFIG_SERIAL_SOFTWARE_FIFO
488 Use an interrupt handler for receiving data on the
489 serial port. It also enables using hardware handshake
490 (RTS/CTS) and UART's built-in FIFO. Set the number of
491 bytes the interrupt driven input buffer should have.
493 Leave undefined to disable this feature, including
494 disable the buffer and hardware handshake.
496 - Console UART Number:
500 If defined internal UART1 (and not UART0) is used
501 as default U-Boot console.
503 - Boot Delay: CONFIG_BOOTDELAY - in seconds
504 Delay before automatically booting the default image;
505 set to -1 to disable autoboot.
507 See doc/README.autoboot for these options that
508 work with CONFIG_BOOTDELAY. None are required.
509 CONFIG_BOOT_RETRY_TIME
510 CONFIG_BOOT_RETRY_MIN
511 CONFIG_AUTOBOOT_KEYED
512 CONFIG_AUTOBOOT_PROMPT
513 CONFIG_AUTOBOOT_DELAY_STR
514 CONFIG_AUTOBOOT_STOP_STR
515 CONFIG_AUTOBOOT_DELAY_STR2
516 CONFIG_AUTOBOOT_STOP_STR2
517 CONFIG_ZERO_BOOTDELAY_CHECK
518 CONFIG_RESET_TO_RETRY
522 Only needed when CONFIG_BOOTDELAY is enabled;
523 define a command string that is automatically executed
524 when no character is read on the console interface
525 within "Boot Delay" after reset.
528 This can be used to pass arguments to the bootm
529 command. The value of CONFIG_BOOTARGS goes into the
530 environment value "bootargs".
532 CONFIG_RAMBOOT and CONFIG_NFSBOOT
533 The value of these goes into the environment as
534 "ramboot" and "nfsboot" respectively, and can be used
535 as a convenience, when switching between booting from
541 When this option is #defined, the existence of the
542 environment variable "preboot" will be checked
543 immediately before starting the CONFIG_BOOTDELAY
544 countdown and/or running the auto-boot command resp.
545 entering interactive mode.
547 This feature is especially useful when "preboot" is
548 automatically generated or modified. For an example
549 see the LWMON board specific code: here "preboot" is
550 modified when the user holds down a certain
551 combination of keys on the (special) keyboard when
554 - Serial Download Echo Mode:
556 If defined to 1, all characters received during a
557 serial download (using the "loads" command) are
558 echoed back. This might be needed by some terminal
559 emulations (like "cu"), but may as well just take
560 time on others. This setting #define's the initial
561 value of the "loads_echo" environment variable.
563 - Kgdb Serial Baudrate: (if CFG_CMD_KGDB is defined)
565 Select one of the baudrates listed in
566 CFG_BAUDRATE_TABLE, see below.
570 Most monitor functions can be selected (or
571 de-selected) by adjusting the definition of
572 CONFIG_COMMANDS; to select individual functions,
573 #define CONFIG_COMMANDS by "OR"ing any of the
576 #define enables commands:
577 -------------------------
578 CFG_CMD_ASKENV * ask for env variable
579 CFG_CMD_AUTOSCRIPT Autoscript Support
581 CFG_CMD_BEDBUG * Include BedBug Debugger
582 CFG_CMD_BMP * BMP support
583 CFG_CMD_BSP * Board specific commands
585 CFG_CMD_CACHE * icache, dcache
586 CFG_CMD_CONSOLE coninfo
587 CFG_CMD_DATE * support for RTC, date/time...
588 CFG_CMD_DHCP * DHCP support
589 CFG_CMD_DIAG * Diagnostics
590 CFG_CMD_DOC * Disk-On-Chip Support
591 CFG_CMD_DTT * Digital Therm and Thermostat
592 CFG_CMD_ECHO * echo arguments
593 CFG_CMD_EEPROM * EEPROM read/write support
594 CFG_CMD_ELF * bootelf, bootvx
596 CFG_CMD_FDC * Floppy Disk Support
597 CFG_CMD_FAT * FAT partition support
598 CFG_CMD_FDOS * Dos diskette Support
599 CFG_CMD_FLASH flinfo, erase, protect
600 CFG_CMD_FPGA FPGA device initialization support
601 CFG_CMD_HWFLOW * RTS/CTS hw flow control
602 CFG_CMD_I2C * I2C serial bus support
603 CFG_CMD_IDE * IDE harddisk support
605 CFG_CMD_IMLS List all found images
606 CFG_CMD_IMMAP * IMMR dump support
607 CFG_CMD_IRQ * irqinfo
608 CFG_CMD_ITEST Integer/string test of 2 values
609 CFG_CMD_JFFS2 * JFFS2 Support
613 CFG_CMD_MEMORY md, mm, nm, mw, cp, cmp, crc, base,
615 CFG_CMD_MISC Misc functions like sleep etc
616 CFG_CMD_MMC * MMC memory mapped support
617 CFG_CMD_MII * MII utility commands
618 CFG_CMD_NAND * NAND support
619 CFG_CMD_NET bootp, tftpboot, rarpboot
620 CFG_CMD_PCI * pciinfo
621 CFG_CMD_PCMCIA * PCMCIA support
622 CFG_CMD_PING * send ICMP ECHO_REQUEST to network host
623 CFG_CMD_PORTIO * Port I/O
624 CFG_CMD_REGINFO * Register dump
625 CFG_CMD_RUN run command in env variable
626 CFG_CMD_SAVES * save S record dump
627 CFG_CMD_SCSI * SCSI Support
628 CFG_CMD_SDRAM * print SDRAM configuration information
629 CFG_CMD_SETGETDCR Support for DCR Register access (4xx only)
630 CFG_CMD_SPI * SPI serial bus support
631 CFG_CMD_USB * USB support
632 CFG_CMD_VFD * VFD support (TRAB)
633 CFG_CMD_BSP * Board SPecific functions
634 CFG_CMD_CDP * Cisco Discover Protocol support
635 -----------------------------------------------
638 CONFIG_CMD_DFL Default configuration; at the moment
639 this is includes all commands, except
640 the ones marked with "*" in the list
643 If you don't define CONFIG_COMMANDS it defaults to
644 CONFIG_CMD_DFL in include/cmd_confdefs.h. A board can
645 override the default settings in the respective
648 EXAMPLE: If you want all functions except of network
649 support you can write:
651 #define CONFIG_COMMANDS (CFG_CMD_ALL & ~CFG_CMD_NET)
654 Note: Don't enable the "icache" and "dcache" commands
655 (configuration option CFG_CMD_CACHE) unless you know
656 what you (and your U-Boot users) are doing. Data
657 cache cannot be enabled on systems like the 8xx or
658 8260 (where accesses to the IMMR region must be
659 uncached), and it cannot be disabled on all other
660 systems where we (mis-) use the data cache to hold an
661 initial stack and some data.
664 XXX - this list needs to get updated!
668 If this variable is defined, it enables watchdog
669 support. There must be support in the platform specific
670 code for a watchdog. For the 8xx and 8260 CPUs, the
671 SIU Watchdog feature is enabled in the SYPCR
675 CONFIG_VERSION_VARIABLE
676 If this variable is defined, an environment variable
677 named "ver" is created by U-Boot showing the U-Boot
678 version as printed by the "version" command.
679 This variable is readonly.
683 When CFG_CMD_DATE is selected, the type of the RTC
684 has to be selected, too. Define exactly one of the
687 CONFIG_RTC_MPC8xx - use internal RTC of MPC8xx
688 CONFIG_RTC_PCF8563 - use Philips PCF8563 RTC
689 CONFIG_RTC_MC146818 - use MC146818 RTC
690 CONFIG_RTC_DS1307 - use Maxim, Inc. DS1307 RTC
691 CONFIG_RTC_DS1337 - use Maxim, Inc. DS1337 RTC
692 CONFIG_RTC_DS1338 - use Maxim, Inc. DS1338 RTC
693 CONFIG_RTC_DS164x - use Dallas DS164x RTC
694 CONFIG_RTC_MAX6900 - use Maxim, Inc. MAX6900 RTC
696 Note that if the RTC uses I2C, then the I2C interface
697 must also be configured. See I2C Support, below.
701 When CONFIG_TIMESTAMP is selected, the timestamp
702 (date and time) of an image is printed by image
703 commands like bootm or iminfo. This option is
704 automatically enabled when you select CFG_CMD_DATE .
707 CONFIG_MAC_PARTITION and/or CONFIG_DOS_PARTITION
708 and/or CONFIG_ISO_PARTITION
710 If IDE or SCSI support is enabled (CFG_CMD_IDE or
711 CFG_CMD_SCSI) you must configure support for at least
712 one partition type as well.
715 CONFIG_IDE_RESET_ROUTINE - this is defined in several
716 board configurations files but used nowhere!
718 CONFIG_IDE_RESET - is this is defined, IDE Reset will
719 be performed by calling the function
720 ide_set_reset(int reset)
721 which has to be defined in a board specific file
726 Set this to enable ATAPI support.
731 Set this to enable support for disks larger than 137GB
732 Also look at CFG_64BIT_LBA ,CFG_64BIT_VSPRINTF and CFG_64BIT_STRTOUL
733 Whithout these , LBA48 support uses 32bit variables and will 'only'
734 support disks up to 2.1TB.
737 When enabled, makes the IDE subsystem use 64bit sector addresses.
741 At the moment only there is only support for the
742 SYM53C8XX SCSI controller; define
743 CONFIG_SCSI_SYM53C8XX to enable it.
745 CFG_SCSI_MAX_LUN [8], CFG_SCSI_MAX_SCSI_ID [7] and
746 CFG_SCSI_MAX_DEVICE [CFG_SCSI_MAX_SCSI_ID *
747 CFG_SCSI_MAX_LUN] can be adjusted to define the
748 maximum numbers of LUNs, SCSI ID's and target
750 CFG_SCSI_SYM53C8XX_CCF to fix clock timing (80Mhz)
752 - NETWORK Support (PCI):
754 Support for Intel 8254x gigabit chips.
757 Support for Intel 82557/82559/82559ER chips.
758 Optional CONFIG_EEPRO100_SROM_WRITE enables eeprom
759 write routine for first time initialisation.
762 Support for Digital 2114x chips.
763 Optional CONFIG_TULIP_SELECT_MEDIA for board specific
764 modem chip initialisation (KS8761/QS6611).
767 Support for National dp83815 chips.
770 Support for National dp8382[01] gigabit chips.
772 - NETWORK Support (other):
774 CONFIG_DRIVER_LAN91C96
775 Support for SMSC's LAN91C96 chips.
778 Define this to hold the physical address
779 of the LAN91C96's I/O space
781 CONFIG_LAN91C96_USE_32_BIT
782 Define this to enable 32 bit addressing
784 CONFIG_DRIVER_SMC91111
785 Support for SMSC's LAN91C111 chip
788 Define this to hold the physical address
789 of the device (I/O space)
791 CONFIG_SMC_USE_32_BIT
792 Define this if data bus is 32 bits
794 CONFIG_SMC_USE_IOFUNCS
795 Define this to use i/o functions instead of macros
796 (some hardware wont work with macros)
799 At the moment only the UHCI host controller is
800 supported (PIP405, MIP405, MPC5200); define
801 CONFIG_USB_UHCI to enable it.
802 define CONFIG_USB_KEYBOARD to enable the USB Keyboard
803 and define CONFIG_USB_STORAGE to enable the USB
806 Supported are USB Keyboards and USB Floppy drives
808 MPC5200 USB requires additional defines:
810 for 528 MHz Clock: 0x0001bbbb
812 for differential drivers: 0x00001000
813 for single ended drivers: 0x00005000
817 The MMC controller on the Intel PXA is supported. To
818 enable this define CONFIG_MMC. The MMC can be
819 accessed from the boot prompt by mapping the device
820 to physical memory similar to flash. Command line is
821 enabled with CFG_CMD_MMC. The MMC driver also works with
822 the FAT fs. This is enabled with CFG_CMD_FAT.
824 - Journaling Flash filesystem support:
825 CONFIG_JFFS2_NAND, CONFIG_JFFS2_NAND_OFF, CONFIG_JFFS2_NAND_SIZE,
826 CONFIG_JFFS2_NAND_DEV
827 Define these for a default partition on a NAND device
829 CFG_JFFS2_FIRST_SECTOR,
830 CFG_JFFS2_FIRST_BANK, CFG_JFFS2_NUM_BANKS
831 Define these for a default partition on a NOR device
834 Define this to create an own partition. You have to provide a
835 function struct part_info* jffs2_part_info(int part_num)
837 If you define only one JFFS2 partition you may also want to
838 #define CFG_JFFS_SINGLE_PART 1
839 to disable the command chpart. This is the default when you
840 have not defined a custom partition
845 Define this to enable standard (PC-Style) keyboard
849 Standard PC keyboard driver with US (is default) and
850 GERMAN key layout (switch via environment 'keymap=de') support.
851 Export function i8042_kbd_init, i8042_tstc and i8042_getc
852 for cfb_console. Supports cursor blinking.
857 Define this to enable video support (for output to
862 Enable Chips & Technologies 69000 Video chip
864 CONFIG_VIDEO_SMI_LYNXEM
865 Enable Silicon Motion SMI 712/710/810 Video chip. The
866 video output is selected via environment 'videoout'
867 (1 = LCD and 2 = CRT). If videoout is undefined, CRT is
870 For the CT69000 and SMI_LYNXEM drivers, videomode is
871 selected via environment 'videomode'. Two diferent ways
873 - "videomode=num" 'num' is a standard LiLo mode numbers.
874 Following standard modes are supported (* is default):
876 Colors 640x480 800x600 1024x768 1152x864 1280x1024
877 -------------+---------------------------------------------
878 8 bits | 0x301* 0x303 0x305 0x161 0x307
879 15 bits | 0x310 0x313 0x316 0x162 0x319
880 16 bits | 0x311 0x314 0x317 0x163 0x31A
881 24 bits | 0x312 0x315 0x318 ? 0x31B
882 -------------+---------------------------------------------
883 (i.e. setenv videomode 317; saveenv; reset;)
885 - "videomode=bootargs" all the video parameters are parsed
886 from the bootargs. (See drivers/videomodes.c)
889 CONFIG_VIDEO_SED13806
890 Enable Epson SED13806 driver. This driver supports 8bpp
891 and 16bpp modes defined by CONFIG_VIDEO_SED13806_8BPP
892 or CONFIG_VIDEO_SED13806_16BPP
897 Define this to enable a custom keyboard support.
898 This simply calls drv_keyboard_init() which must be
899 defined in your board-specific files.
900 The only board using this so far is RBC823.
902 - LCD Support: CONFIG_LCD
904 Define this to enable LCD support (for output to LCD
905 display); also select one of the supported displays
906 by defining one of these:
908 CONFIG_NEC_NL6448AC33:
910 NEC NL6448AC33-18. Active, color, single scan.
912 CONFIG_NEC_NL6448BC20
914 NEC NL6448BC20-08. 6.5", 640x480.
915 Active, color, single scan.
917 CONFIG_NEC_NL6448BC33_54
919 NEC NL6448BC33-54. 10.4", 640x480.
920 Active, color, single scan.
924 Sharp 320x240. Active, color, single scan.
925 It isn't 16x9, and I am not sure what it is.
927 CONFIG_SHARP_LQ64D341
929 Sharp LQ64D341 display, 640x480.
930 Active, color, single scan.
934 HLD1045 display, 640x480.
935 Active, color, single scan.
939 Optrex CBL50840-2 NF-FW 99 22 M5
941 Hitachi LMG6912RPFC-00T
945 320x240. Black & white.
947 Normally display is black on white background; define
948 CFG_WHITE_ON_BLACK to get it inverted.
950 - Splash Screen Support: CONFIG_SPLASH_SCREEN
952 If this option is set, the environment is checked for
953 a variable "splashimage". If found, the usual display
954 of logo, copyright and system information on the LCD
955 is suppressed and the BMP image at the address
956 specified in "splashimage" is loaded instead. The
957 console is redirected to the "nulldev", too. This
958 allows for a "silent" boot where a splash screen is
959 loaded very quickly after power-on.
961 - Compression support:
964 If this option is set, support for bzip2 compressed
965 images is included. If not, only uncompressed and gzip
966 compressed images are supported.
968 NOTE: the bzip2 algorithm requires a lot of RAM, so
969 the malloc area (as defined by CFG_MALLOC_LEN) should
975 The address of PHY on MII bus.
977 CONFIG_PHY_CLOCK_FREQ (ppc4xx)
979 The clock frequency of the MII bus
983 If this option is set, support for speed/duplex
984 detection of Gigabit PHY is included.
986 CONFIG_PHY_RESET_DELAY
988 Some PHY like Intel LXT971A need extra delay after
989 reset before any MII register access is possible.
990 For such PHY, set this option to the usec delay
991 required. (minimum 300usec for LXT971A)
993 CONFIG_PHY_CMD_DELAY (ppc4xx)
995 Some PHY like Intel LXT971A need extra delay after
996 command issued before MII status register can be read
1003 Define a default value for ethernet address to use
1004 for the respective ethernet interface, in case this
1005 is not determined automatically.
1010 Define a default value for the IP address to use for
1011 the default ethernet interface, in case this is not
1012 determined through e.g. bootp.
1014 - Server IP address:
1017 Defines a default value for theIP address of a TFTP
1018 server to contact when using the "tftboot" command.
1020 - BOOTP Recovery Mode:
1021 CONFIG_BOOTP_RANDOM_DELAY
1023 If you have many targets in a network that try to
1024 boot using BOOTP, you may want to avoid that all
1025 systems send out BOOTP requests at precisely the same
1026 moment (which would happen for instance at recovery
1027 from a power failure, when all systems will try to
1028 boot, thus flooding the BOOTP server. Defining
1029 CONFIG_BOOTP_RANDOM_DELAY causes a random delay to be
1030 inserted before sending out BOOTP requests. The
1031 following delays are insterted then:
1033 1st BOOTP request: delay 0 ... 1 sec
1034 2nd BOOTP request: delay 0 ... 2 sec
1035 3rd BOOTP request: delay 0 ... 4 sec
1037 BOOTP requests: delay 0 ... 8 sec
1039 - DHCP Advanced Options:
1042 You can fine tune the DHCP functionality by adding
1043 these flags to the CONFIG_BOOTP_MASK define:
1045 CONFIG_BOOTP_DNS2 - If a DHCP client requests the DNS
1046 serverip from a DHCP server, it is possible that more
1047 than one DNS serverip is offered to the client.
1048 If CONFIG_BOOTP_DNS2 is enabled, the secondary DNS
1049 serverip will be stored in the additional environment
1050 variable "dnsip2". The first DNS serverip is always
1051 stored in the variable "dnsip", when CONFIG_BOOTP_DNS
1052 is added to the CONFIG_BOOTP_MASK.
1054 CONFIG_BOOTP_SEND_HOSTNAME - Some DHCP servers are capable
1055 to do a dynamic update of a DNS server. To do this, they
1056 need the hostname of the DHCP requester.
1057 If CONFIG_BOOP_SEND_HOSTNAME is added to the
1058 CONFIG_BOOTP_MASK, the content of the "hostname"
1059 environment variable is passed as option 12 to
1063 CONFIG_CDP_DEVICE_ID
1065 The device id used in CDP trigger frames.
1067 CONFIG_CDP_DEVICE_ID_PREFIX
1069 A two character string which is prefixed to the MAC address
1074 A printf format string which contains the ascii name of
1075 the port. Normally is set to "eth%d" which sets
1076 eth0 for the first ethernet, eth1 for the second etc.
1078 CONFIG_CDP_CAPABILITIES
1080 A 32bit integer which indicates the device capabilities;
1081 0x00000010 for a normal host which does not forwards.
1085 An ascii string containing the version of the software.
1089 An ascii string containing the name of the platform.
1093 A 32bit integer sent on the trigger.
1095 CONFIG_CDP_POWER_CONSUMPTION
1097 A 16bit integer containing the power consumption of the
1098 device in .1 of milliwatts.
1100 CONFIG_CDP_APPLIANCE_VLAN_TYPE
1102 A byte containing the id of the VLAN.
1104 - Status LED: CONFIG_STATUS_LED
1106 Several configurations allow to display the current
1107 status using a LED. For instance, the LED will blink
1108 fast while running U-Boot code, stop blinking as
1109 soon as a reply to a BOOTP request was received, and
1110 start blinking slow once the Linux kernel is running
1111 (supported by a status LED driver in the Linux
1112 kernel). Defining CONFIG_STATUS_LED enables this
1115 - CAN Support: CONFIG_CAN_DRIVER
1117 Defining CONFIG_CAN_DRIVER enables CAN driver support
1118 on those systems that support this (optional)
1119 feature, like the TQM8xxL modules.
1121 - I2C Support: CONFIG_HARD_I2C | CONFIG_SOFT_I2C
1123 These enable I2C serial bus commands. Defining either of
1124 (but not both of) CONFIG_HARD_I2C or CONFIG_SOFT_I2C will
1125 include the appropriate I2C driver for the selected cpu.
1127 This will allow you to use i2c commands at the u-boot
1128 command line (as long as you set CFG_CMD_I2C in
1129 CONFIG_COMMANDS) and communicate with i2c based realtime
1130 clock chips. See common/cmd_i2c.c for a description of the
1131 command line interface.
1133 CONFIG_HARD_I2C selects the CPM hardware driver for I2C.
1135 CONFIG_SOFT_I2C configures u-boot to use a software (aka
1136 bit-banging) driver instead of CPM or similar hardware
1139 There are several other quantities that must also be
1140 defined when you define CONFIG_HARD_I2C or CONFIG_SOFT_I2C.
1142 In both cases you will need to define CFG_I2C_SPEED
1143 to be the frequency (in Hz) at which you wish your i2c bus
1144 to run and CFG_I2C_SLAVE to be the address of this node (ie
1145 the cpu's i2c node address).
1147 Now, the u-boot i2c code for the mpc8xx (cpu/mpc8xx/i2c.c)
1148 sets the cpu up as a master node and so its address should
1149 therefore be cleared to 0 (See, eg, MPC823e User's Manual
1150 p.16-473). So, set CFG_I2C_SLAVE to 0.
1152 That's all that's required for CONFIG_HARD_I2C.
1154 If you use the software i2c interface (CONFIG_SOFT_I2C)
1155 then the following macros need to be defined (examples are
1156 from include/configs/lwmon.h):
1160 (Optional). Any commands necessary to enable the I2C
1161 controller or configure ports.
1163 eg: #define I2C_INIT (immr->im_cpm.cp_pbdir |= PB_SCL)
1167 (Only for MPC8260 CPU). The I/O port to use (the code
1168 assumes both bits are on the same port). Valid values
1169 are 0..3 for ports A..D.
1173 The code necessary to make the I2C data line active
1174 (driven). If the data line is open collector, this
1177 eg: #define I2C_ACTIVE (immr->im_cpm.cp_pbdir |= PB_SDA)
1181 The code necessary to make the I2C data line tri-stated
1182 (inactive). If the data line is open collector, this
1185 eg: #define I2C_TRISTATE (immr->im_cpm.cp_pbdir &= ~PB_SDA)
1189 Code that returns TRUE if the I2C data line is high,
1192 eg: #define I2C_READ ((immr->im_cpm.cp_pbdat & PB_SDA) != 0)
1196 If <bit> is TRUE, sets the I2C data line high. If it
1197 is FALSE, it clears it (low).
1199 eg: #define I2C_SDA(bit) \
1200 if(bit) immr->im_cpm.cp_pbdat |= PB_SDA; \
1201 else immr->im_cpm.cp_pbdat &= ~PB_SDA
1205 If <bit> is TRUE, sets the I2C clock line high. If it
1206 is FALSE, it clears it (low).
1208 eg: #define I2C_SCL(bit) \
1209 if(bit) immr->im_cpm.cp_pbdat |= PB_SCL; \
1210 else immr->im_cpm.cp_pbdat &= ~PB_SCL
1214 This delay is invoked four times per clock cycle so this
1215 controls the rate of data transfer. The data rate thus
1216 is 1 / (I2C_DELAY * 4). Often defined to be something
1219 #define I2C_DELAY udelay(2)
1223 When a board is reset during an i2c bus transfer
1224 chips might think that the current transfer is still
1225 in progress. On some boards it is possible to access
1226 the i2c SCLK line directly, either by using the
1227 processor pin as a GPIO or by having a second pin
1228 connected to the bus. If this option is defined a
1229 custom i2c_init_board() routine in boards/xxx/board.c
1230 is run early in the boot sequence.
1232 CONFIG_I2CFAST (PPC405GP|PPC405EP only)
1234 This option enables configuration of bi_iic_fast[] flags
1235 in u-boot bd_info structure based on u-boot environment
1236 variable "i2cfast". (see also i2cfast)
1238 - SPI Support: CONFIG_SPI
1240 Enables SPI driver (so far only tested with
1241 SPI EEPROM, also an instance works with Crystal A/D and
1242 D/As on the SACSng board)
1246 Enables extended (16-bit) SPI EEPROM addressing.
1247 (symmetrical to CONFIG_I2C_X)
1251 Enables a software (bit-bang) SPI driver rather than
1252 using hardware support. This is a general purpose
1253 driver that only requires three general I/O port pins
1254 (two outputs, one input) to function. If this is
1255 defined, the board configuration must define several
1256 SPI configuration items (port pins to use, etc). For
1257 an example, see include/configs/sacsng.h.
1259 - FPGA Support: CONFIG_FPGA_COUNT
1261 Specify the number of FPGA devices to support.
1265 Used to specify the types of FPGA devices. For example,
1266 #define CONFIG_FPGA CFG_XILINX_VIRTEX2
1268 CFG_FPGA_PROG_FEEDBACK
1270 Enable printing of hash marks during FPGA configuration.
1274 Enable checks on FPGA configuration interface busy
1275 status by the configuration function. This option
1276 will require a board or device specific function to
1281 If defined, a function that provides delays in the FPGA
1282 configuration driver.
1284 CFG_FPGA_CHECK_CTRLC
1285 Allow Control-C to interrupt FPGA configuration
1287 CFG_FPGA_CHECK_ERROR
1289 Check for configuration errors during FPGA bitfile
1290 loading. For example, abort during Virtex II
1291 configuration if the INIT_B line goes low (which
1292 indicated a CRC error).
1296 Maximum time to wait for the INIT_B line to deassert
1297 after PROB_B has been deasserted during a Virtex II
1298 FPGA configuration sequence. The default time is 500
1303 Maximum time to wait for BUSY to deassert during
1304 Virtex II FPGA configuration. The default is 5 mS.
1306 CFG_FPGA_WAIT_CONFIG
1308 Time to wait after FPGA configuration. The default is
1311 - Configuration Management:
1314 If defined, this string will be added to the U-Boot
1315 version information (U_BOOT_VERSION)
1317 - Vendor Parameter Protection:
1319 U-Boot considers the values of the environment
1320 variables "serial#" (Board Serial Number) and
1321 "ethaddr" (Ethernet Address) to be parameters that
1322 are set once by the board vendor / manufacturer, and
1323 protects these variables from casual modification by
1324 the user. Once set, these variables are read-only,
1325 and write or delete attempts are rejected. You can
1326 change this behviour:
1328 If CONFIG_ENV_OVERWRITE is #defined in your config
1329 file, the write protection for vendor parameters is
1330 completely disabled. Anybody can change or delete
1333 Alternatively, if you #define _both_ CONFIG_ETHADDR
1334 _and_ CONFIG_OVERWRITE_ETHADDR_ONCE, a default
1335 ethernet address is installed in the environment,
1336 which can be changed exactly ONCE by the user. [The
1337 serial# is unaffected by this, i. e. it remains
1343 Define this variable to enable the reservation of
1344 "protected RAM", i. e. RAM which is not overwritten
1345 by U-Boot. Define CONFIG_PRAM to hold the number of
1346 kB you want to reserve for pRAM. You can overwrite
1347 this default value by defining an environment
1348 variable "pram" to the number of kB you want to
1349 reserve. Note that the board info structure will
1350 still show the full amount of RAM. If pRAM is
1351 reserved, a new environment variable "mem" will
1352 automatically be defined to hold the amount of
1353 remaining RAM in a form that can be passed as boot
1354 argument to Linux, for instance like that:
1356 setenv bootargs ... mem=\$(mem)
1359 This way you can tell Linux not to use this memory,
1360 either, which results in a memory region that will
1361 not be affected by reboots.
1363 *WARNING* If your board configuration uses automatic
1364 detection of the RAM size, you must make sure that
1365 this memory test is non-destructive. So far, the
1366 following board configurations are known to be
1369 ETX094, IVMS8, IVML24, SPD8xx, TQM8xxL,
1370 HERMES, IP860, RPXlite, LWMON, LANTEC,
1371 PCU_E, FLAGADM, TQM8260
1376 Define this variable to stop the system in case of a
1377 fatal error, so that you have to reset it manually.
1378 This is probably NOT a good idea for an embedded
1379 system where you want to system to reboot
1380 automatically as fast as possible, but it may be
1381 useful during development since you can try to debug
1382 the conditions that lead to the situation.
1384 CONFIG_NET_RETRY_COUNT
1386 This variable defines the number of retries for
1387 network operations like ARP, RARP, TFTP, or BOOTP
1388 before giving up the operation. If not defined, a
1389 default value of 5 is used.
1391 - Command Interpreter:
1394 Enable auto completion of commands using TAB.
1398 Define this variable to enable the "hush" shell (from
1399 Busybox) as command line interpreter, thus enabling
1400 powerful command line syntax like
1401 if...then...else...fi conditionals or `&&' and '||'
1402 constructs ("shell scripts").
1404 If undefined, you get the old, much simpler behaviour
1405 with a somewhat smaller memory footprint.
1410 This defines the secondary prompt string, which is
1411 printed when the command interpreter needs more input
1412 to complete a command. Usually "> ".
1416 In the current implementation, the local variables
1417 space and global environment variables space are
1418 separated. Local variables are those you define by
1419 simply typing `name=value'. To access a local
1420 variable later on, you have write `$name' or
1421 `${name}'; to execute the contents of a variable
1422 directly type `$name' at the command prompt.
1424 Global environment variables are those you use
1425 setenv/printenv to work with. To run a command stored
1426 in such a variable, you need to use the run command,
1427 and you must not use the '$' sign to access them.
1429 To store commands and special characters in a
1430 variable, please use double quotation marks
1431 surrounding the whole text of the variable, instead
1432 of the backslashes before semicolons and special
1435 - Default Environment:
1436 CONFIG_EXTRA_ENV_SETTINGS
1438 Define this to contain any number of null terminated
1439 strings (variable = value pairs) that will be part of
1440 the default environment compiled into the boot image.
1442 For example, place something like this in your
1443 board's config file:
1445 #define CONFIG_EXTRA_ENV_SETTINGS \
1449 Warning: This method is based on knowledge about the
1450 internal format how the environment is stored by the
1451 U-Boot code. This is NOT an official, exported
1452 interface! Although it is unlikely that this format
1453 will change soon, there is no guarantee either.
1454 You better know what you are doing here.
1456 Note: overly (ab)use of the default environment is
1457 discouraged. Make sure to check other ways to preset
1458 the environment like the autoscript function or the
1461 - DataFlash Support:
1462 CONFIG_HAS_DATAFLASH
1464 Defining this option enables DataFlash features and
1465 allows to read/write in Dataflash via the standard
1468 - SystemACE Support:
1471 Adding this option adds support for Xilinx SystemACE
1472 chips attached via some sort of local bus. The address
1473 of the chip must alsh be defined in the
1474 CFG_SYSTEMACE_BASE macro. For example:
1476 #define CONFIG_SYSTEMACE
1477 #define CFG_SYSTEMACE_BASE 0xf0000000
1479 When SystemACE support is added, the "ace" device type
1480 becomes available to the fat commands, i.e. fatls.
1482 - Show boot progress:
1483 CONFIG_SHOW_BOOT_PROGRESS
1485 Defining this option allows to add some board-
1486 specific code (calling a user-provided function
1487 "show_boot_progress(int)") that enables you to show
1488 the system's boot progress on some display (for
1489 example, some LED's) on your board. At the moment,
1490 the following checkpoints are implemented:
1493 1 common/cmd_bootm.c before attempting to boot an image
1494 -1 common/cmd_bootm.c Image header has bad magic number
1495 2 common/cmd_bootm.c Image header has correct magic number
1496 -2 common/cmd_bootm.c Image header has bad checksum
1497 3 common/cmd_bootm.c Image header has correct checksum
1498 -3 common/cmd_bootm.c Image data has bad checksum
1499 4 common/cmd_bootm.c Image data has correct checksum
1500 -4 common/cmd_bootm.c Image is for unsupported architecture
1501 5 common/cmd_bootm.c Architecture check OK
1502 -5 common/cmd_bootm.c Wrong Image Type (not kernel, multi, standalone)
1503 6 common/cmd_bootm.c Image Type check OK
1504 -6 common/cmd_bootm.c gunzip uncompression error
1505 -7 common/cmd_bootm.c Unimplemented compression type
1506 7 common/cmd_bootm.c Uncompression OK
1507 -8 common/cmd_bootm.c Wrong Image Type (not kernel, multi, standalone)
1508 8 common/cmd_bootm.c Image Type check OK
1509 -9 common/cmd_bootm.c Unsupported OS (not Linux, BSD, VxWorks, QNX)
1510 9 common/cmd_bootm.c Start initial ramdisk verification
1511 -10 common/cmd_bootm.c Ramdisk header has bad magic number
1512 -11 common/cmd_bootm.c Ramdisk header has bad checksum
1513 10 common/cmd_bootm.c Ramdisk header is OK
1514 -12 common/cmd_bootm.c Ramdisk data has bad checksum
1515 11 common/cmd_bootm.c Ramdisk data has correct checksum
1516 12 common/cmd_bootm.c Ramdisk verification complete, start loading
1517 -13 common/cmd_bootm.c Wrong Image Type (not PPC Linux Ramdisk)
1518 13 common/cmd_bootm.c Start multifile image verification
1519 14 common/cmd_bootm.c No initial ramdisk, no multifile, continue.
1520 15 common/cmd_bootm.c All preparation done, transferring control to OS
1522 -30 lib_ppc/board.c Fatal error, hang the system
1523 -31 post/post.c POST test failed, detected by post_output_backlog()
1524 -32 post/post.c POST test failed, detected by post_run_single()
1526 -1 common/cmd_doc.c Bad usage of "doc" command
1527 -1 common/cmd_doc.c No boot device
1528 -1 common/cmd_doc.c Unknown Chip ID on boot device
1529 -1 common/cmd_doc.c Read Error on boot device
1530 -1 common/cmd_doc.c Image header has bad magic number
1532 -1 common/cmd_ide.c Bad usage of "ide" command
1533 -1 common/cmd_ide.c No boot device
1534 -1 common/cmd_ide.c Unknown boot device
1535 -1 common/cmd_ide.c Unknown partition table
1536 -1 common/cmd_ide.c Invalid partition type
1537 -1 common/cmd_ide.c Read Error on boot device
1538 -1 common/cmd_ide.c Image header has bad magic number
1540 -1 common/cmd_nand.c Bad usage of "nand" command
1541 -1 common/cmd_nand.c No boot device
1542 -1 common/cmd_nand.c Unknown Chip ID on boot device
1543 -1 common/cmd_nand.c Read Error on boot device
1544 -1 common/cmd_nand.c Image header has bad magic number
1546 -1 common/env_common.c Environment has a bad CRC, using default
1552 [so far only for SMDK2400 and TRAB boards]
1554 - Modem support endable:
1555 CONFIG_MODEM_SUPPORT
1557 - RTS/CTS Flow control enable:
1560 - Modem debug support:
1561 CONFIG_MODEM_SUPPORT_DEBUG
1563 Enables debugging stuff (char screen[1024], dbg())
1564 for modem support. Useful only with BDI2000.
1566 - Interrupt support (PPC):
1568 There are common interrupt_init() and timer_interrupt()
1569 for all PPC archs. interrupt_init() calls interrupt_init_cpu()
1570 for cpu specific initialization. interrupt_init_cpu()
1571 should set decrementer_count to appropriate value. If
1572 cpu resets decrementer automatically after interrupt
1573 (ppc4xx) it should set decrementer_count to zero.
1574 timer_interrupt() calls timer_interrupt_cpu() for cpu
1575 specific handling. If board has watchdog / status_led
1576 / other_activity_monitor it works automatically from
1577 general timer_interrupt().
1581 In the target system modem support is enabled when a
1582 specific key (key combination) is pressed during
1583 power-on. Otherwise U-Boot will boot normally
1584 (autoboot). The key_pressed() fuction is called from
1585 board_init(). Currently key_pressed() is a dummy
1586 function, returning 1 and thus enabling modem
1589 If there are no modem init strings in the
1590 environment, U-Boot proceed to autoboot; the
1591 previous output (banner, info printfs) will be
1594 See also: doc/README.Modem
1597 Configuration Settings:
1598 -----------------------
1600 - CFG_LONGHELP: Defined when you want long help messages included;
1601 undefine this when you're short of memory.
1603 - CFG_PROMPT: This is what U-Boot prints on the console to
1604 prompt for user input.
1606 - CFG_CBSIZE: Buffer size for input from the Console
1608 - CFG_PBSIZE: Buffer size for Console output
1610 - CFG_MAXARGS: max. Number of arguments accepted for monitor commands
1612 - CFG_BARGSIZE: Buffer size for Boot Arguments which are passed to
1613 the application (usually a Linux kernel) when it is
1616 - CFG_BAUDRATE_TABLE:
1617 List of legal baudrate settings for this board.
1619 - CFG_CONSOLE_INFO_QUIET
1620 Suppress display of console information at boot.
1622 - CFG_CONSOLE_IS_IN_ENV
1623 If the board specific function
1624 extern int overwrite_console (void);
1625 returns 1, the stdin, stderr and stdout are switched to the
1626 serial port, else the settings in the environment are used.
1628 - CFG_CONSOLE_OVERWRITE_ROUTINE
1629 Enable the call to overwrite_console().
1631 - CFG_CONSOLE_ENV_OVERWRITE
1632 Enable overwrite of previous console environment settings.
1634 - CFG_MEMTEST_START, CFG_MEMTEST_END:
1635 Begin and End addresses of the area used by the
1639 Enable an alternate, more extensive memory test.
1641 - CFG_MEMTEST_SCRATCH:
1642 Scratch address used by the alternate memory test
1643 You only need to set this if address zero isn't writeable
1645 - CFG_TFTP_LOADADDR:
1646 Default load address for network file downloads
1648 - CFG_LOADS_BAUD_CHANGE:
1649 Enable temporary baudrate change while serial download
1652 Physical start address of SDRAM. _Must_ be 0 here.
1655 Physical start address of Motherboard I/O (if using a
1659 Physical start address of Flash memory.
1662 Physical start address of boot monitor code (set by
1663 make config files to be same as the text base address
1664 (TEXT_BASE) used when linking) - same as
1665 CFG_FLASH_BASE when booting from flash.
1668 Size of memory reserved for monitor code, used to
1669 determine _at_compile_time_ (!) if the environment is
1670 embedded within the U-Boot image, or in a separate
1674 Size of DRAM reserved for malloc() use.
1677 Maximum size of memory mapped by the startup code of
1678 the Linux kernel; all data that must be processed by
1679 the Linux kernel (bd_info, boot arguments, eventually
1680 initrd image) must be put below this limit.
1682 - CFG_MAX_FLASH_BANKS:
1683 Max number of Flash memory banks
1685 - CFG_MAX_FLASH_SECT:
1686 Max number of sectors on a Flash chip
1688 - CFG_FLASH_ERASE_TOUT:
1689 Timeout for Flash erase operations (in ms)
1691 - CFG_FLASH_WRITE_TOUT:
1692 Timeout for Flash write operations (in ms)
1694 - CFG_FLASH_LOCK_TOUT
1695 Timeout for Flash set sector lock bit operation (in ms)
1697 - CFG_FLASH_UNLOCK_TOUT
1698 Timeout for Flash clear lock bits operation (in ms)
1700 - CFG_FLASH_PROTECTION
1701 If defined, hardware flash sectors protection is used
1702 instead of U-Boot software protection.
1704 - CFG_DIRECT_FLASH_TFTP:
1706 Enable TFTP transfers directly to flash memory;
1707 without this option such a download has to be
1708 performed in two steps: (1) download to RAM, and (2)
1709 copy from RAM to flash.
1711 The two-step approach is usually more reliable, since
1712 you can check if the download worked before you erase
1713 the flash, but in some situations (when sytem RAM is
1714 too limited to allow for a tempory copy of the
1715 downloaded image) this option may be very useful.
1718 Define if the flash driver uses extra elements in the
1719 common flash structure for storing flash geometry.
1721 - CFG_FLASH_CFI_DRIVER
1722 This option also enables the building of the cfi_flash driver
1723 in the drivers directory
1725 - CFG_RX_ETH_BUFFER:
1726 Defines the number of ethernet receive buffers. On some
1727 ethernet controllers it is recommended to set this value
1728 to 8 or even higher (EEPRO100 or 405 EMAC), since all
1729 buffers can be full shortly after enabling the interface
1730 on high ethernet traffic.
1731 Defaults to 4 if not defined.
1733 The following definitions that deal with the placement and management
1734 of environment data (variable area); in general, we support the
1735 following configurations:
1737 - CFG_ENV_IS_IN_FLASH:
1739 Define this if the environment is in flash memory.
1741 a) The environment occupies one whole flash sector, which is
1742 "embedded" in the text segment with the U-Boot code. This
1743 happens usually with "bottom boot sector" or "top boot
1744 sector" type flash chips, which have several smaller
1745 sectors at the start or the end. For instance, such a
1746 layout can have sector sizes of 8, 2x4, 16, Nx32 kB. In
1747 such a case you would place the environment in one of the
1748 4 kB sectors - with U-Boot code before and after it. With
1749 "top boot sector" type flash chips, you would put the
1750 environment in one of the last sectors, leaving a gap
1751 between U-Boot and the environment.
1755 Offset of environment data (variable area) to the
1756 beginning of flash memory; for instance, with bottom boot
1757 type flash chips the second sector can be used: the offset
1758 for this sector is given here.
1760 CFG_ENV_OFFSET is used relative to CFG_FLASH_BASE.
1764 This is just another way to specify the start address of
1765 the flash sector containing the environment (instead of
1768 - CFG_ENV_SECT_SIZE:
1770 Size of the sector containing the environment.
1773 b) Sometimes flash chips have few, equal sized, BIG sectors.
1774 In such a case you don't want to spend a whole sector for
1779 If you use this in combination with CFG_ENV_IS_IN_FLASH
1780 and CFG_ENV_SECT_SIZE, you can specify to use only a part
1781 of this flash sector for the environment. This saves
1782 memory for the RAM copy of the environment.
1784 It may also save flash memory if you decide to use this
1785 when your environment is "embedded" within U-Boot code,
1786 since then the remainder of the flash sector could be used
1787 for U-Boot code. It should be pointed out that this is
1788 STRONGLY DISCOURAGED from a robustness point of view:
1789 updating the environment in flash makes it always
1790 necessary to erase the WHOLE sector. If something goes
1791 wrong before the contents has been restored from a copy in
1792 RAM, your target system will be dead.
1794 - CFG_ENV_ADDR_REDUND
1797 These settings describe a second storage area used to hold
1798 a redundand copy of the environment data, so that there is
1799 a valid backup copy in case there is a power failure during
1800 a "saveenv" operation.
1802 BE CAREFUL! Any changes to the flash layout, and some changes to the
1803 source code will make it necessary to adapt <board>/u-boot.lds*
1807 - CFG_ENV_IS_IN_NVRAM:
1809 Define this if you have some non-volatile memory device
1810 (NVRAM, battery buffered SRAM) which you want to use for the
1816 These two #defines are used to determin the memory area you
1817 want to use for environment. It is assumed that this memory
1818 can just be read and written to, without any special
1821 BE CAREFUL! The first access to the environment happens quite early
1822 in U-Boot initalization (when we try to get the setting of for the
1823 console baudrate). You *MUST* have mappend your NVRAM area then, or
1826 Please note that even with NVRAM we still use a copy of the
1827 environment in RAM: we could work on NVRAM directly, but we want to
1828 keep settings there always unmodified except somebody uses "saveenv"
1829 to save the current settings.
1832 - CFG_ENV_IS_IN_EEPROM:
1834 Use this if you have an EEPROM or similar serial access
1835 device and a driver for it.
1840 These two #defines specify the offset and size of the
1841 environment area within the total memory of your EEPROM.
1843 - CFG_I2C_EEPROM_ADDR:
1844 If defined, specified the chip address of the EEPROM device.
1845 The default address is zero.
1847 - CFG_EEPROM_PAGE_WRITE_BITS:
1848 If defined, the number of bits used to address bytes in a
1849 single page in the EEPROM device. A 64 byte page, for example
1850 would require six bits.
1852 - CFG_EEPROM_PAGE_WRITE_DELAY_MS:
1853 If defined, the number of milliseconds to delay between
1854 page writes. The default is zero milliseconds.
1856 - CFG_I2C_EEPROM_ADDR_LEN:
1857 The length in bytes of the EEPROM memory array address. Note
1858 that this is NOT the chip address length!
1860 - CFG_I2C_EEPROM_ADDR_OVERFLOW:
1861 EEPROM chips that implement "address overflow" are ones
1862 like Catalyst 24WC04/08/16 which has 9/10/11 bits of
1863 address and the extra bits end up in the "chip address" bit
1864 slots. This makes a 24WC08 (1Kbyte) chip look like four 256
1867 Note that we consider the length of the address field to
1868 still be one byte because the extra address bits are hidden
1869 in the chip address.
1872 The size in bytes of the EEPROM device.
1875 - CFG_ENV_IS_IN_DATAFLASH:
1877 Define this if you have a DataFlash memory device which you
1878 want to use for the environment.
1884 These three #defines specify the offset and size of the
1885 environment area within the total memory of your DataFlash placed
1886 at the specified address.
1888 - CFG_ENV_IS_IN_NAND:
1890 Define this if you have a NAND device which you want to use
1891 for the environment.
1896 These two #defines specify the offset and size of the environment
1897 area within the first NAND device.
1899 - CFG_SPI_INIT_OFFSET
1901 Defines offset to the initial SPI buffer area in DPRAM. The
1902 area is used at an early stage (ROM part) if the environment
1903 is configured to reside in the SPI EEPROM: We need a 520 byte
1904 scratch DPRAM area. It is used between the two initialization
1905 calls (spi_init_f() and spi_init_r()). A value of 0xB00 seems
1906 to be a good choice since it makes it far enough from the
1907 start of the data area as well as from the stack pointer.
1909 Please note that the environment is read-only as long as the monitor
1910 has been relocated to RAM and a RAM copy of the environment has been
1911 created; also, when using EEPROM you will have to use getenv_r()
1912 until then to read environment variables.
1914 The environment is protected by a CRC32 checksum. Before the monitor
1915 is relocated into RAM, as a result of a bad CRC you will be working
1916 with the compiled-in default environment - *silently*!!! [This is
1917 necessary, because the first environment variable we need is the
1918 "baudrate" setting for the console - if we have a bad CRC, we don't
1919 have any device yet where we could complain.]
1921 Note: once the monitor has been relocated, then it will complain if
1922 the default environment is used; a new CRC is computed as soon as you
1923 use the "saveenv" command to store a valid environment.
1925 - CFG_FAULT_ECHO_LINK_DOWN:
1926 Echo the inverted Ethernet link state to the fault LED.
1928 Note: If this option is active, then CFG_FAULT_MII_ADDR
1929 also needs to be defined.
1931 - CFG_FAULT_MII_ADDR:
1932 MII address of the PHY to check for the Ethernet link state.
1934 - CFG_64BIT_VSPRINTF:
1935 Makes vsprintf (and all *printf functions) support printing
1936 of 64bit values by using the L quantifier
1938 - CFG_64BIT_STRTOUL:
1939 Adds simple_strtoull that returns a 64bit value
1941 Low Level (hardware related) configuration options:
1942 ---------------------------------------------------
1944 - CFG_CACHELINE_SIZE:
1945 Cache Line Size of the CPU.
1948 Default address of the IMMR after system reset.
1950 Needed on some 8260 systems (MPC8260ADS, PQ2FADS-ZU,
1951 and RPXsuper) to be able to adjust the position of
1952 the IMMR register after a reset.
1954 - Floppy Disk Support:
1955 CFG_FDC_DRIVE_NUMBER
1957 the default drive number (default value 0)
1961 defines the spacing between fdc chipset registers
1966 defines the offset of register from address. It
1967 depends on which part of the data bus is connected to
1968 the fdc chipset. (default value 0)
1970 If CFG_ISA_IO_STRIDE CFG_ISA_IO_OFFSET and
1971 CFG_FDC_DRIVE_NUMBER are undefined, they take their
1974 if CFG_FDC_HW_INIT is defined, then the function
1975 fdc_hw_init() is called at the beginning of the FDC
1976 setup. fdc_hw_init() must be provided by the board
1977 source code. It is used to make hardware dependant
1980 - CFG_IMMR: Physical address of the Internal Memory.
1981 DO NOT CHANGE unless you know exactly what you're
1982 doing! (11-4) [MPC8xx/82xx systems only]
1984 - CFG_INIT_RAM_ADDR:
1986 Start address of memory area that can be used for
1987 initial data and stack; please note that this must be
1988 writable memory that is working WITHOUT special
1989 initialization, i. e. you CANNOT use normal RAM which
1990 will become available only after programming the
1991 memory controller and running certain initialization
1994 U-Boot uses the following memory types:
1995 - MPC8xx and MPC8260: IMMR (internal memory of the CPU)
1996 - MPC824X: data cache
1997 - PPC4xx: data cache
1999 - CFG_GBL_DATA_OFFSET:
2001 Offset of the initial data structure in the memory
2002 area defined by CFG_INIT_RAM_ADDR. Usually
2003 CFG_GBL_DATA_OFFSET is chosen such that the initial
2004 data is located at the end of the available space
2005 (sometimes written as (CFG_INIT_RAM_END -
2006 CFG_INIT_DATA_SIZE), and the initial stack is just
2007 below that area (growing from (CFG_INIT_RAM_ADDR +
2008 CFG_GBL_DATA_OFFSET) downward.
2011 On the MPC824X (or other systems that use the data
2012 cache for initial memory) the address chosen for
2013 CFG_INIT_RAM_ADDR is basically arbitrary - it must
2014 point to an otherwise UNUSED address space between
2015 the top of RAM and the start of the PCI space.
2017 - CFG_SIUMCR: SIU Module Configuration (11-6)
2019 - CFG_SYPCR: System Protection Control (11-9)
2021 - CFG_TBSCR: Time Base Status and Control (11-26)
2023 - CFG_PISCR: Periodic Interrupt Status and Control (11-31)
2025 - CFG_PLPRCR: PLL, Low-Power, and Reset Control Register (15-30)
2027 - CFG_SCCR: System Clock and reset Control Register (15-27)
2029 - CFG_OR_TIMING_SDRAM:
2033 periodic timer for refresh
2035 - CFG_DER: Debug Event Register (37-47)
2037 - FLASH_BASE0_PRELIM, FLASH_BASE1_PRELIM, CFG_REMAP_OR_AM,
2038 CFG_PRELIM_OR_AM, CFG_OR_TIMING_FLASH, CFG_OR0_REMAP,
2039 CFG_OR0_PRELIM, CFG_BR0_PRELIM, CFG_OR1_REMAP, CFG_OR1_PRELIM,
2041 Memory Controller Definitions: BR0/1 and OR0/1 (FLASH)
2043 - SDRAM_BASE2_PRELIM, SDRAM_BASE3_PRELIM, SDRAM_MAX_SIZE,
2044 CFG_OR_TIMING_SDRAM, CFG_OR2_PRELIM, CFG_BR2_PRELIM,
2045 CFG_OR3_PRELIM, CFG_BR3_PRELIM:
2046 Memory Controller Definitions: BR2/3 and OR2/3 (SDRAM)
2048 - CFG_MAMR_PTA, CFG_MPTPR_2BK_4K, CFG_MPTPR_1BK_4K, CFG_MPTPR_2BK_8K,
2049 CFG_MPTPR_1BK_8K, CFG_MAMR_8COL, CFG_MAMR_9COL:
2050 Machine Mode Register and Memory Periodic Timer
2051 Prescaler definitions (SDRAM timing)
2053 - CFG_I2C_UCODE_PATCH, CFG_I2C_DPMEM_OFFSET [0x1FC0]:
2054 enable I2C microcode relocation patch (MPC8xx);
2055 define relocation offset in DPRAM [DSP2]
2057 - CFG_SPI_UCODE_PATCH, CFG_SPI_DPMEM_OFFSET [0x1FC0]:
2058 enable SPI microcode relocation patch (MPC8xx);
2059 define relocation offset in DPRAM [SCC4]
2062 Use OSCM clock mode on MBX8xx board. Be careful,
2063 wrong setting might damage your board. Read
2064 doc/README.MBX before setting this variable!
2066 - CFG_CPM_POST_WORD_ADDR: (MPC8xx, MPC8260 only)
2067 Offset of the bootmode word in DPRAM used by post
2068 (Power On Self Tests). This definition overrides
2069 #define'd default value in commproc.h resp.
2072 - CFG_PCI_SLV_MEM_LOCAL, CFG_PCI_SLV_MEM_BUS, CFG_PICMR0_MASK_ATTRIB,
2073 CFG_PCI_MSTR0_LOCAL, CFG_PCIMSK0_MASK, CFG_PCI_MSTR1_LOCAL,
2074 CFG_PCIMSK1_MASK, CFG_PCI_MSTR_MEM_LOCAL, CFG_PCI_MSTR_MEM_BUS,
2075 CFG_CPU_PCI_MEM_START, CFG_PCI_MSTR_MEM_SIZE, CFG_POCMR0_MASK_ATTRIB,
2076 CFG_PCI_MSTR_MEMIO_LOCAL, CFG_PCI_MSTR_MEMIO_BUS, CPU_PCI_MEMIO_START,
2077 CFG_PCI_MSTR_MEMIO_SIZE, CFG_POCMR1_MASK_ATTRIB, CFG_PCI_MSTR_IO_LOCAL,
2078 CFG_PCI_MSTR_IO_BUS, CFG_CPU_PCI_IO_START, CFG_PCI_MSTR_IO_SIZE,
2079 CFG_POCMR2_MASK_ATTRIB: (MPC826x only)
2080 Overrides the default PCI memory map in cpu/mpc8260/pci.c if set.
2082 - CONFIG_ETHER_ON_FEC[12]
2083 Define to enable FEC[12] on a 8xx series processor.
2085 - CONFIG_FEC[12]_PHY
2086 Define to the hardcoded PHY address which corresponds
2087 to the given FEC; i. e.
2088 #define CONFIG_FEC1_PHY 4
2089 means that the PHY with address 4 is connected to FEC1
2091 When set to -1, means to probe for first available.
2093 - CONFIG_FEC[12]_PHY_NORXERR
2094 The PHY does not have a RXERR line (RMII only).
2095 (so program the FEC to ignore it).
2098 Enable RMII mode for all FECs.
2099 Note that this is a global option, we can't
2100 have one FEC in standard MII mode and another in RMII mode.
2102 - CONFIG_CRC32_VERIFY
2103 Add a verify option to the crc32 command.
2106 => crc32 -v <address> <count> <crc32>
2108 Where address/count indicate a memory area
2109 and crc32 is the correct crc32 which the
2113 Add the "loopw" memory command. This only takes effect if
2114 the memory commands are activated globally (CFG_CMD_MEM).
2116 Building the Software:
2117 ======================
2119 Building U-Boot has been tested in native PPC environments (on a
2120 PowerBook G3 running LinuxPPC 2000) and in cross environments
2121 (running RedHat 6.x and 7.x Linux on x86, Solaris 2.6 on a SPARC, and
2124 If you are not using a native PPC environment, it is assumed that you
2125 have the GNU cross compiling tools available in your path and named
2126 with a prefix of "powerpc-linux-". If this is not the case, (e.g. if
2127 you are using Monta Vista's Hard Hat Linux CDK 1.2) you must change
2128 the definition of CROSS_COMPILE in Makefile. For HHL on a 4xx CPU,
2131 CROSS_COMPILE = ppc_4xx-
2134 U-Boot is intended to be simple to build. After installing the
2135 sources you must configure U-Boot for one specific board type. This
2140 where "NAME_config" is the name of one of the existing
2141 configurations; the following names are supported:
2143 ADCIOP_config FPS860L_config omap730p2_config
2144 ADS860_config GEN860T_config pcu_e_config
2146 AR405_config GENIETV_config PIP405_config
2147 at91rm9200dk_config GTH_config QS823_config
2148 CANBT_config hermes_config QS850_config
2149 cmi_mpc5xx_config hymod_config QS860T_config
2150 cogent_common_config IP860_config RPXlite_config
2151 cogent_mpc8260_config IVML24_config RPXlite_DW_config
2152 cogent_mpc8xx_config IVMS8_config RPXsuper_config
2153 CPCI405_config JSE_config rsdproto_config
2154 CPCIISER4_config LANTEC_config Sandpoint8240_config
2155 csb272_config lwmon_config sbc8260_config
2156 CU824_config MBX860T_config sbc8560_33_config
2157 DUET_ADS_config MBX_config sbc8560_66_config
2158 EBONY_config MPC8260ADS_config SM850_config
2159 ELPT860_config MPC8540ADS_config SPD823TS_config
2160 ESTEEM192E_config MPC8560ADS_config stxgp3_config
2161 ETX094_config NETVIA_config SXNI855T_config
2162 FADS823_config omap1510inn_config TQM823L_config
2163 FADS850SAR_config omap1610h2_config TQM850L_config
2164 FADS860T_config omap1610inn_config TQM855L_config
2165 FPS850L_config omap5912osk_config TQM860L_config
2170 Note: for some board special configuration names may exist; check if
2171 additional information is available from the board vendor; for
2172 instance, the TQM823L systems are available without (standard)
2173 or with LCD support. You can select such additional "features"
2174 when chosing the configuration, i. e.
2177 - will configure for a plain TQM823L, i. e. no LCD support
2179 make TQM823L_LCD_config
2180 - will configure for a TQM823L with U-Boot console on LCD
2185 Finally, type "make all", and you should get some working U-Boot
2186 images ready for download to / installation on your system:
2188 - "u-boot.bin" is a raw binary image
2189 - "u-boot" is an image in ELF binary format
2190 - "u-boot.srec" is in Motorola S-Record format
2193 Please be aware that the Makefiles assume you are using GNU make, so
2194 for instance on NetBSD you might need to use "gmake" instead of
2198 If the system board that you have is not listed, then you will need
2199 to port U-Boot to your hardware platform. To do this, follow these
2202 1. Add a new configuration option for your board to the toplevel
2203 "Makefile" and to the "MAKEALL" script, using the existing
2204 entries as examples. Note that here and at many other places
2205 boards and other names are listed in alphabetical sort order. Please
2207 2. Create a new directory to hold your board specific code. Add any
2208 files you need. In your board directory, you will need at least
2209 the "Makefile", a "<board>.c", "flash.c" and "u-boot.lds".
2210 3. Create a new configuration file "include/configs/<board>.h" for
2212 3. If you're porting U-Boot to a new CPU, then also create a new
2213 directory to hold your CPU specific code. Add any files you need.
2214 4. Run "make <board>_config" with your new name.
2215 5. Type "make", and you should get a working "u-boot.srec" file
2216 to be installed on your target system.
2217 6. Debug and solve any problems that might arise.
2218 [Of course, this last step is much harder than it sounds.]
2221 Testing of U-Boot Modifications, Ports to New Hardware, etc.:
2222 ==============================================================
2224 If you have modified U-Boot sources (for instance added a new board
2225 or support for new devices, a new CPU, etc.) you are expected to
2226 provide feedback to the other developers. The feedback normally takes
2227 the form of a "patch", i. e. a context diff against a certain (latest
2228 official or latest in CVS) version of U-Boot sources.
2230 But before you submit such a patch, please verify that your modifi-
2231 cation did not break existing code. At least make sure that *ALL* of
2232 the supported boards compile WITHOUT ANY compiler warnings. To do so,
2233 just run the "MAKEALL" script, which will configure and build U-Boot
2234 for ALL supported system. Be warned, this will take a while. You can
2235 select which (cross) compiler to use by passing a `CROSS_COMPILE'
2236 environment variable to the script, i. e. to use the cross tools from
2237 MontaVista's Hard Hat Linux you can type
2239 CROSS_COMPILE=ppc_8xx- MAKEALL
2241 or to build on a native PowerPC system you can type
2243 CROSS_COMPILE=' ' MAKEALL
2245 See also "U-Boot Porting Guide" below.
2248 Monitor Commands - Overview:
2249 ============================
2251 go - start application at address 'addr'
2252 run - run commands in an environment variable
2253 bootm - boot application image from memory
2254 bootp - boot image via network using BootP/TFTP protocol
2255 tftpboot- boot image via network using TFTP protocol
2256 and env variables "ipaddr" and "serverip"
2257 (and eventually "gatewayip")
2258 rarpboot- boot image via network using RARP/TFTP protocol
2259 diskboot- boot from IDE devicebootd - boot default, i.e., run 'bootcmd'
2260 loads - load S-Record file over serial line
2261 loadb - load binary file over serial line (kermit mode)
2263 mm - memory modify (auto-incrementing)
2264 nm - memory modify (constant address)
2265 mw - memory write (fill)
2267 cmp - memory compare
2268 crc32 - checksum calculation
2269 imd - i2c memory display
2270 imm - i2c memory modify (auto-incrementing)
2271 inm - i2c memory modify (constant address)
2272 imw - i2c memory write (fill)
2273 icrc32 - i2c checksum calculation
2274 iprobe - probe to discover valid I2C chip addresses
2275 iloop - infinite loop on address range
2276 isdram - print SDRAM configuration information
2277 sspi - SPI utility commands
2278 base - print or set address offset
2279 printenv- print environment variables
2280 setenv - set environment variables
2281 saveenv - save environment variables to persistent storage
2282 protect - enable or disable FLASH write protection
2283 erase - erase FLASH memory
2284 flinfo - print FLASH memory information
2285 bdinfo - print Board Info structure
2286 iminfo - print header information for application image
2287 coninfo - print console devices and informations
2288 ide - IDE sub-system
2289 loop - infinite loop on address range
2290 loopw - infinite write loop on address range
2291 mtest - simple RAM test
2292 icache - enable or disable instruction cache
2293 dcache - enable or disable data cache
2294 reset - Perform RESET of the CPU
2295 echo - echo args to console
2296 version - print monitor version
2297 help - print online help
2298 ? - alias for 'help'
2301 Monitor Commands - Detailed Description:
2302 ========================================
2306 For now: just type "help <command>".
2309 Environment Variables:
2310 ======================
2312 U-Boot supports user configuration using Environment Variables which
2313 can be made persistent by saving to Flash memory.
2315 Environment Variables are set using "setenv", printed using
2316 "printenv", and saved to Flash using "saveenv". Using "setenv"
2317 without a value can be used to delete a variable from the
2318 environment. As long as you don't save the environment you are
2319 working with an in-memory copy. In case the Flash area containing the
2320 environment is erased by accident, a default environment is provided.
2322 Some configuration options can be set using Environment Variables:
2324 baudrate - see CONFIG_BAUDRATE
2326 bootdelay - see CONFIG_BOOTDELAY
2328 bootcmd - see CONFIG_BOOTCOMMAND
2330 bootargs - Boot arguments when booting an RTOS image
2332 bootfile - Name of the image to load with TFTP
2334 autoload - if set to "no" (any string beginning with 'n'),
2335 "bootp" will just load perform a lookup of the
2336 configuration from the BOOTP server, but not try to
2337 load any image using TFTP
2339 autostart - if set to "yes", an image loaded using the "bootp",
2340 "rarpboot", "tftpboot" or "diskboot" commands will
2341 be automatically started (by internally calling
2344 If set to "no", a standalone image passed to the
2345 "bootm" command will be copied to the load address
2346 (and eventually uncompressed), but NOT be started.
2347 This can be used to load and uncompress arbitrary
2350 i2cfast - (PPC405GP|PPC405EP only)
2351 if set to 'y' configures Linux I2C driver for fast
2352 mode (400kHZ). This environment variable is used in
2353 initialization code. So, for changes to be effective
2354 it must be saved and board must be reset.
2356 initrd_high - restrict positioning of initrd images:
2357 If this variable is not set, initrd images will be
2358 copied to the highest possible address in RAM; this
2359 is usually what you want since it allows for
2360 maximum initrd size. If for some reason you want to
2361 make sure that the initrd image is loaded below the
2362 CFG_BOOTMAPSZ limit, you can set this environment
2363 variable to a value of "no" or "off" or "0".
2364 Alternatively, you can set it to a maximum upper
2365 address to use (U-Boot will still check that it
2366 does not overwrite the U-Boot stack and data).
2368 For instance, when you have a system with 16 MB
2369 RAM, and want to reserve 4 MB from use by Linux,
2370 you can do this by adding "mem=12M" to the value of
2371 the "bootargs" variable. However, now you must make
2372 sure that the initrd image is placed in the first
2373 12 MB as well - this can be done with
2375 setenv initrd_high 00c00000
2377 If you set initrd_high to 0xFFFFFFFF, this is an
2378 indication to U-Boot that all addresses are legal
2379 for the Linux kernel, including addresses in flash
2380 memory. In this case U-Boot will NOT COPY the
2381 ramdisk at all. This may be useful to reduce the
2382 boot time on your system, but requires that this
2383 feature is supported by your Linux kernel.
2385 ipaddr - IP address; needed for tftpboot command
2387 loadaddr - Default load address for commands like "bootp",
2388 "rarpboot", "tftpboot", "loadb" or "diskboot"
2390 loads_echo - see CONFIG_LOADS_ECHO
2392 serverip - TFTP server IP address; needed for tftpboot command
2394 bootretry - see CONFIG_BOOT_RETRY_TIME
2396 bootdelaykey - see CONFIG_AUTOBOOT_DELAY_STR
2398 bootstopkey - see CONFIG_AUTOBOOT_STOP_STR
2400 ethprime - When CONFIG_NET_MULTI is enabled controls which
2401 interface is used first.
2403 ethact - When CONFIG_NET_MULTI is enabled controls which
2404 interface is currently active. For example you
2405 can do the following
2407 => setenv ethact FEC ETHERNET
2408 => ping 192.168.0.1 # traffic sent on FEC ETHERNET
2409 => setenv ethact SCC ETHERNET
2410 => ping 10.0.0.1 # traffic sent on SCC ETHERNET
2412 netretry - When set to "no" each network operation will
2413 either succeed or fail without retrying.
2414 When set to "once" the network operation will
2415 fail when all the available network interfaces
2416 are tried once without success.
2417 Useful on scripts which control the retry operation
2420 vlan - When set to a value < 4095 the traffic over
2421 ethernet is encapsulated/received over 802.1q
2424 The following environment variables may be used and automatically
2425 updated by the network boot commands ("bootp" and "rarpboot"),
2426 depending the information provided by your boot server:
2428 bootfile - see above
2429 dnsip - IP address of your Domain Name Server
2430 dnsip2 - IP address of your secondary Domain Name Server
2431 gatewayip - IP address of the Gateway (Router) to use
2432 hostname - Target hostname
2434 netmask - Subnet Mask
2435 rootpath - Pathname of the root filesystem on the NFS server
2436 serverip - see above
2439 There are two special Environment Variables:
2441 serial# - contains hardware identification information such
2442 as type string and/or serial number
2443 ethaddr - Ethernet address
2445 These variables can be set only once (usually during manufacturing of
2446 the board). U-Boot refuses to delete or overwrite these variables
2447 once they have been set once.
2450 Further special Environment Variables:
2452 ver - Contains the U-Boot version string as printed
2453 with the "version" command. This variable is
2454 readonly (see CONFIG_VERSION_VARIABLE).
2457 Please note that changes to some configuration parameters may take
2458 only effect after the next boot (yes, that's just like Windoze :-).
2461 Command Line Parsing:
2462 =====================
2464 There are two different command line parsers available with U-Boot:
2465 the old "simple" one, and the much more powerful "hush" shell:
2467 Old, simple command line parser:
2468 --------------------------------
2470 - supports environment variables (through setenv / saveenv commands)
2471 - several commands on one line, separated by ';'
2472 - variable substitution using "... $(name) ..." syntax
2473 - special characters ('$', ';') can be escaped by prefixing with '\',
2475 setenv bootcmd bootm \$(address)
2476 - You can also escape text by enclosing in single apostrophes, for example:
2477 setenv addip 'setenv bootargs $bootargs ip=$ipaddr:$serverip:$gatewayip:$netmask:$hostname::off'
2482 - similar to Bourne shell, with control structures like
2483 if...then...else...fi, for...do...done; while...do...done,
2484 until...do...done, ...
2485 - supports environment ("global") variables (through setenv / saveenv
2486 commands) and local shell variables (through standard shell syntax
2487 "name=value"); only environment variables can be used with "run"
2493 (1) If a command line (or an environment variable executed by a "run"
2494 command) contains several commands separated by semicolon, and
2495 one of these commands fails, then the remaining commands will be
2498 (2) If you execute several variables with one call to run (i. e.
2499 calling run with a list af variables as arguments), any failing
2500 command will cause "run" to terminate, i. e. the remaining
2501 variables are not executed.
2503 Note for Redundant Ethernet Interfaces:
2504 =======================================
2506 Some boards come with redundant ethernet interfaces; U-Boot supports
2507 such configurations and is capable of automatic selection of a
2508 "working" interface when needed. MAC assignment works as follows:
2510 Network interfaces are numbered eth0, eth1, eth2, ... Corresponding
2511 MAC addresses can be stored in the environment as "ethaddr" (=>eth0),
2512 "eth1addr" (=>eth1), "eth2addr", ...
2514 If the network interface stores some valid MAC address (for instance
2515 in SROM), this is used as default address if there is NO correspon-
2516 ding setting in the environment; if the corresponding environment
2517 variable is set, this overrides the settings in the card; that means:
2519 o If the SROM has a valid MAC address, and there is no address in the
2520 environment, the SROM's address is used.
2522 o If there is no valid address in the SROM, and a definition in the
2523 environment exists, then the value from the environment variable is
2526 o If both the SROM and the environment contain a MAC address, and
2527 both addresses are the same, this MAC address is used.
2529 o If both the SROM and the environment contain a MAC address, and the
2530 addresses differ, the value from the environment is used and a
2533 o If neither SROM nor the environment contain a MAC address, an error
2540 The "boot" commands of this monitor operate on "image" files which
2541 can be basicly anything, preceeded by a special header; see the
2542 definitions in include/image.h for details; basicly, the header
2543 defines the following image properties:
2545 * Target Operating System (Provisions for OpenBSD, NetBSD, FreeBSD,
2546 4.4BSD, Linux, SVR4, Esix, Solaris, Irix, SCO, Dell, NCR, VxWorks,
2547 LynxOS, pSOS, QNX, RTEMS, ARTOS;
2548 Currently supported: Linux, NetBSD, VxWorks, QNX, RTEMS, ARTOS, LynxOS).
2549 * Target CPU Architecture (Provisions for Alpha, ARM, Intel x86,
2550 IA64, MIPS, NIOS, PowerPC, IBM S390, SuperH, Sparc, Sparc 64 Bit;
2551 Currently supported: ARM, Intel x86, MIPS, NIOS, PowerPC).
2552 * Compression Type (uncompressed, gzip, bzip2)
2558 The header is marked by a special Magic Number, and both the header
2559 and the data portions of the image are secured against corruption by
2566 Although U-Boot should support any OS or standalone application
2567 easily, the main focus has always been on Linux during the design of
2570 U-Boot includes many features that so far have been part of some
2571 special "boot loader" code within the Linux kernel. Also, any
2572 "initrd" images to be used are no longer part of one big Linux image;
2573 instead, kernel and "initrd" are separate images. This implementation
2574 serves several purposes:
2576 - the same features can be used for other OS or standalone
2577 applications (for instance: using compressed images to reduce the
2578 Flash memory footprint)
2580 - it becomes much easier to port new Linux kernel versions because
2581 lots of low-level, hardware dependent stuff are done by U-Boot
2583 - the same Linux kernel image can now be used with different "initrd"
2584 images; of course this also means that different kernel images can
2585 be run with the same "initrd". This makes testing easier (you don't
2586 have to build a new "zImage.initrd" Linux image when you just
2587 change a file in your "initrd"). Also, a field-upgrade of the
2588 software is easier now.
2594 Porting Linux to U-Boot based systems:
2595 ---------------------------------------
2597 U-Boot cannot save you from doing all the necessary modifications to
2598 configure the Linux device drivers for use with your target hardware
2599 (no, we don't intend to provide a full virtual machine interface to
2602 But now you can ignore ALL boot loader code (in arch/ppc/mbxboot).
2604 Just make sure your machine specific header file (for instance
2605 include/asm-ppc/tqm8xx.h) includes the same definition of the Board
2606 Information structure as we define in include/u-boot.h, and make
2607 sure that your definition of IMAP_ADDR uses the same value as your
2608 U-Boot configuration in CFG_IMMR.
2611 Configuring the Linux kernel:
2612 -----------------------------
2614 No specific requirements for U-Boot. Make sure you have some root
2615 device (initial ramdisk, NFS) for your target system.
2618 Building a Linux Image:
2619 -----------------------
2621 With U-Boot, "normal" build targets like "zImage" or "bzImage" are
2622 not used. If you use recent kernel source, a new build target
2623 "uImage" will exist which automatically builds an image usable by
2624 U-Boot. Most older kernels also have support for a "pImage" target,
2625 which was introduced for our predecessor project PPCBoot and uses a
2626 100% compatible format.
2635 The "uImage" build target uses a special tool (in 'tools/mkimage') to
2636 encapsulate a compressed Linux kernel image with header information,
2637 CRC32 checksum etc. for use with U-Boot. This is what we are doing:
2639 * build a standard "vmlinux" kernel image (in ELF binary format):
2641 * convert the kernel into a raw binary image:
2643 ${CROSS_COMPILE}-objcopy -O binary \
2644 -R .note -R .comment \
2645 -S vmlinux linux.bin
2647 * compress the binary image:
2651 * package compressed binary image for U-Boot:
2653 mkimage -A ppc -O linux -T kernel -C gzip \
2654 -a 0 -e 0 -n "Linux Kernel Image" \
2655 -d linux.bin.gz uImage
2658 The "mkimage" tool can also be used to create ramdisk images for use
2659 with U-Boot, either separated from the Linux kernel image, or
2660 combined into one file. "mkimage" encapsulates the images with a 64
2661 byte header containing information about target architecture,
2662 operating system, image type, compression method, entry points, time
2663 stamp, CRC32 checksums, etc.
2665 "mkimage" can be called in two ways: to verify existing images and
2666 print the header information, or to build new images.
2668 In the first form (with "-l" option) mkimage lists the information
2669 contained in the header of an existing U-Boot image; this includes
2670 checksum verification:
2672 tools/mkimage -l image
2673 -l ==> list image header information
2675 The second form (with "-d" option) is used to build a U-Boot image
2676 from a "data file" which is used as image payload:
2678 tools/mkimage -A arch -O os -T type -C comp -a addr -e ep \
2679 -n name -d data_file image
2680 -A ==> set architecture to 'arch'
2681 -O ==> set operating system to 'os'
2682 -T ==> set image type to 'type'
2683 -C ==> set compression type 'comp'
2684 -a ==> set load address to 'addr' (hex)
2685 -e ==> set entry point to 'ep' (hex)
2686 -n ==> set image name to 'name'
2687 -d ==> use image data from 'datafile'
2689 Right now, all Linux kernels for PowerPC systems use the same load
2690 address (0x00000000), but the entry point address depends on the
2693 - 2.2.x kernels have the entry point at 0x0000000C,
2694 - 2.3.x and later kernels have the entry point at 0x00000000.
2696 So a typical call to build a U-Boot image would read:
2698 -> tools/mkimage -n '2.4.4 kernel for TQM850L' \
2699 > -A ppc -O linux -T kernel -C gzip -a 0 -e 0 \
2700 > -d /opt/elsk/ppc_8xx/usr/src/linux-2.4.4/arch/ppc/coffboot/vmlinux.gz \
2701 > examples/uImage.TQM850L
2702 Image Name: 2.4.4 kernel for TQM850L
2703 Created: Wed Jul 19 02:34:59 2000
2704 Image Type: PowerPC Linux Kernel Image (gzip compressed)
2705 Data Size: 335725 Bytes = 327.86 kB = 0.32 MB
2706 Load Address: 0x00000000
2707 Entry Point: 0x00000000
2709 To verify the contents of the image (or check for corruption):
2711 -> tools/mkimage -l examples/uImage.TQM850L
2712 Image Name: 2.4.4 kernel for TQM850L
2713 Created: Wed Jul 19 02:34:59 2000
2714 Image Type: PowerPC Linux Kernel Image (gzip compressed)
2715 Data Size: 335725 Bytes = 327.86 kB = 0.32 MB
2716 Load Address: 0x00000000
2717 Entry Point: 0x00000000
2719 NOTE: for embedded systems where boot time is critical you can trade
2720 speed for memory and install an UNCOMPRESSED image instead: this
2721 needs more space in Flash, but boots much faster since it does not
2722 need to be uncompressed:
2724 -> gunzip /opt/elsk/ppc_8xx/usr/src/linux-2.4.4/arch/ppc/coffboot/vmlinux.gz
2725 -> tools/mkimage -n '2.4.4 kernel for TQM850L' \
2726 > -A ppc -O linux -T kernel -C none -a 0 -e 0 \
2727 > -d /opt/elsk/ppc_8xx/usr/src/linux-2.4.4/arch/ppc/coffboot/vmlinux \
2728 > examples/uImage.TQM850L-uncompressed
2729 Image Name: 2.4.4 kernel for TQM850L
2730 Created: Wed Jul 19 02:34:59 2000
2731 Image Type: PowerPC Linux Kernel Image (uncompressed)
2732 Data Size: 792160 Bytes = 773.59 kB = 0.76 MB
2733 Load Address: 0x00000000
2734 Entry Point: 0x00000000
2737 Similar you can build U-Boot images from a 'ramdisk.image.gz' file
2738 when your kernel is intended to use an initial ramdisk:
2740 -> tools/mkimage -n 'Simple Ramdisk Image' \
2741 > -A ppc -O linux -T ramdisk -C gzip \
2742 > -d /LinuxPPC/images/SIMPLE-ramdisk.image.gz examples/simple-initrd
2743 Image Name: Simple Ramdisk Image
2744 Created: Wed Jan 12 14:01:50 2000
2745 Image Type: PowerPC Linux RAMDisk Image (gzip compressed)
2746 Data Size: 566530 Bytes = 553.25 kB = 0.54 MB
2747 Load Address: 0x00000000
2748 Entry Point: 0x00000000
2751 Installing a Linux Image:
2752 -------------------------
2754 To downloading a U-Boot image over the serial (console) interface,
2755 you must convert the image to S-Record format:
2757 objcopy -I binary -O srec examples/image examples/image.srec
2759 The 'objcopy' does not understand the information in the U-Boot
2760 image header, so the resulting S-Record file will be relative to
2761 address 0x00000000. To load it to a given address, you need to
2762 specify the target address as 'offset' parameter with the 'loads'
2765 Example: install the image to address 0x40100000 (which on the
2766 TQM8xxL is in the first Flash bank):
2768 => erase 40100000 401FFFFF
2774 ## Ready for S-Record download ...
2775 ~>examples/image.srec
2776 1 2 3 4 5 6 7 8 9 10 11 12 13 ...
2778 15989 15990 15991 15992
2779 [file transfer complete]
2781 ## Start Addr = 0x00000000
2784 You can check the success of the download using the 'iminfo' command;
2785 this includes a checksum verification so you can be sure no data
2786 corruption happened:
2790 ## Checking Image at 40100000 ...
2791 Image Name: 2.2.13 for initrd on TQM850L
2792 Image Type: PowerPC Linux Kernel Image (gzip compressed)
2793 Data Size: 335725 Bytes = 327 kB = 0 MB
2794 Load Address: 00000000
2795 Entry Point: 0000000c
2796 Verifying Checksum ... OK
2802 The "bootm" command is used to boot an application that is stored in
2803 memory (RAM or Flash). In case of a Linux kernel image, the contents
2804 of the "bootargs" environment variable is passed to the kernel as
2805 parameters. You can check and modify this variable using the
2806 "printenv" and "setenv" commands:
2809 => printenv bootargs
2810 bootargs=root=/dev/ram
2812 => setenv bootargs root=/dev/nfs rw nfsroot=10.0.0.2:/LinuxPPC nfsaddrs=10.0.0.99:10.0.0.2
2814 => printenv bootargs
2815 bootargs=root=/dev/nfs rw nfsroot=10.0.0.2:/LinuxPPC nfsaddrs=10.0.0.99:10.0.0.2
2818 ## Booting Linux kernel at 40020000 ...
2819 Image Name: 2.2.13 for NFS on TQM850L
2820 Image Type: PowerPC Linux Kernel Image (gzip compressed)
2821 Data Size: 381681 Bytes = 372 kB = 0 MB
2822 Load Address: 00000000
2823 Entry Point: 0000000c
2824 Verifying Checksum ... OK
2825 Uncompressing Kernel Image ... OK
2826 Linux version 2.2.13 (wd@denx.local.net) (gcc version 2.95.2 19991024 (release)) #1 Wed Jul 19 02:35:17 MEST 2000
2827 Boot arguments: root=/dev/nfs rw nfsroot=10.0.0.2:/LinuxPPC nfsaddrs=10.0.0.99:10.0.0.2
2828 time_init: decrementer frequency = 187500000/60
2829 Calibrating delay loop... 49.77 BogoMIPS
2830 Memory: 15208k available (700k kernel code, 444k data, 32k init) [c0000000,c1000000]
2833 If you want to boot a Linux kernel with initial ram disk, you pass
2834 the memory addresses of both the kernel and the initrd image (PPBCOOT
2835 format!) to the "bootm" command:
2837 => imi 40100000 40200000
2839 ## Checking Image at 40100000 ...
2840 Image Name: 2.2.13 for initrd on TQM850L
2841 Image Type: PowerPC Linux Kernel Image (gzip compressed)
2842 Data Size: 335725 Bytes = 327 kB = 0 MB
2843 Load Address: 00000000
2844 Entry Point: 0000000c
2845 Verifying Checksum ... OK
2847 ## Checking Image at 40200000 ...
2848 Image Name: Simple Ramdisk Image
2849 Image Type: PowerPC Linux RAMDisk Image (gzip compressed)
2850 Data Size: 566530 Bytes = 553 kB = 0 MB
2851 Load Address: 00000000
2852 Entry Point: 00000000
2853 Verifying Checksum ... OK
2855 => bootm 40100000 40200000
2856 ## Booting Linux kernel at 40100000 ...
2857 Image Name: 2.2.13 for initrd on TQM850L
2858 Image Type: PowerPC Linux Kernel Image (gzip compressed)
2859 Data Size: 335725 Bytes = 327 kB = 0 MB
2860 Load Address: 00000000
2861 Entry Point: 0000000c
2862 Verifying Checksum ... OK
2863 Uncompressing Kernel Image ... OK
2864 ## Loading RAMDisk Image at 40200000 ...
2865 Image Name: Simple Ramdisk Image
2866 Image Type: PowerPC Linux RAMDisk Image (gzip compressed)
2867 Data Size: 566530 Bytes = 553 kB = 0 MB
2868 Load Address: 00000000
2869 Entry Point: 00000000
2870 Verifying Checksum ... OK
2871 Loading Ramdisk ... OK
2872 Linux version 2.2.13 (wd@denx.local.net) (gcc version 2.95.2 19991024 (release)) #1 Wed Jul 19 02:32:08 MEST 2000
2873 Boot arguments: root=/dev/ram
2874 time_init: decrementer frequency = 187500000/60
2875 Calibrating delay loop... 49.77 BogoMIPS
2877 RAMDISK: Compressed image found at block 0
2878 VFS: Mounted root (ext2 filesystem).
2882 More About U-Boot Image Types:
2883 ------------------------------
2885 U-Boot supports the following image types:
2887 "Standalone Programs" are directly runnable in the environment
2888 provided by U-Boot; it is expected that (if they behave
2889 well) you can continue to work in U-Boot after return from
2890 the Standalone Program.
2891 "OS Kernel Images" are usually images of some Embedded OS which
2892 will take over control completely. Usually these programs
2893 will install their own set of exception handlers, device
2894 drivers, set up the MMU, etc. - this means, that you cannot
2895 expect to re-enter U-Boot except by resetting the CPU.
2896 "RAMDisk Images" are more or less just data blocks, and their
2897 parameters (address, size) are passed to an OS kernel that is
2899 "Multi-File Images" contain several images, typically an OS
2900 (Linux) kernel image and one or more data images like
2901 RAMDisks. This construct is useful for instance when you want
2902 to boot over the network using BOOTP etc., where the boot
2903 server provides just a single image file, but you want to get
2904 for instance an OS kernel and a RAMDisk image.
2906 "Multi-File Images" start with a list of image sizes, each
2907 image size (in bytes) specified by an "uint32_t" in network
2908 byte order. This list is terminated by an "(uint32_t)0".
2909 Immediately after the terminating 0 follow the images, one by
2910 one, all aligned on "uint32_t" boundaries (size rounded up to
2911 a multiple of 4 bytes).
2913 "Firmware Images" are binary images containing firmware (like
2914 U-Boot or FPGA images) which usually will be programmed to
2917 "Script files" are command sequences that will be executed by
2918 U-Boot's command interpreter; this feature is especially
2919 useful when you configure U-Boot to use a real shell (hush)
2920 as command interpreter.
2926 One of the features of U-Boot is that you can dynamically load and
2927 run "standalone" applications, which can use some resources of
2928 U-Boot like console I/O functions or interrupt services.
2930 Two simple examples are included with the sources:
2935 'examples/hello_world.c' contains a small "Hello World" Demo
2936 application; it is automatically compiled when you build U-Boot.
2937 It's configured to run at address 0x00040004, so you can play with it
2941 ## Ready for S-Record download ...
2942 ~>examples/hello_world.srec
2943 1 2 3 4 5 6 7 8 9 10 11 ...
2944 [file transfer complete]
2946 ## Start Addr = 0x00040004
2948 => go 40004 Hello World! This is a test.
2949 ## Starting application at 0x00040004 ...
2960 Hit any key to exit ...
2962 ## Application terminated, rc = 0x0
2964 Another example, which demonstrates how to register a CPM interrupt
2965 handler with the U-Boot code, can be found in 'examples/timer.c'.
2966 Here, a CPM timer is set up to generate an interrupt every second.
2967 The interrupt service routine is trivial, just printing a '.'
2968 character, but this is just a demo program. The application can be
2969 controlled by the following keys:
2971 ? - print current values og the CPM Timer registers
2972 b - enable interrupts and start timer
2973 e - stop timer and disable interrupts
2974 q - quit application
2977 ## Ready for S-Record download ...
2978 ~>examples/timer.srec
2979 1 2 3 4 5 6 7 8 9 10 11 ...
2980 [file transfer complete]
2982 ## Start Addr = 0x00040004
2985 ## Starting application at 0x00040004 ...
2988 tgcr @ 0xfff00980, tmr @ 0xfff00990, trr @ 0xfff00994, tcr @ 0xfff00998, tcn @ 0xfff0099c, ter @ 0xfff009b0
2991 [q, b, e, ?] Set interval 1000000 us
2994 [q, b, e, ?] ........
2995 tgcr=0x1, tmr=0xff1c, trr=0x3d09, tcr=0x0, tcn=0xef6, ter=0x0
2998 tgcr=0x1, tmr=0xff1c, trr=0x3d09, tcr=0x0, tcn=0x2ad4, ter=0x0
3001 tgcr=0x1, tmr=0xff1c, trr=0x3d09, tcr=0x0, tcn=0x1efc, ter=0x0
3004 tgcr=0x1, tmr=0xff1c, trr=0x3d09, tcr=0x0, tcn=0x169d, ter=0x0
3006 [q, b, e, ?] ...Stopping timer
3008 [q, b, e, ?] ## Application terminated, rc = 0x0
3014 Over time, many people have reported problems when trying to use the
3015 "minicom" terminal emulation program for serial download. I (wd)
3016 consider minicom to be broken, and recommend not to use it. Under
3017 Unix, I recommend to use C-Kermit for general purpose use (and
3018 especially for kermit binary protocol download ("loadb" command), and
3019 use "cu" for S-Record download ("loads" command).
3021 Nevertheless, if you absolutely want to use it try adding this
3022 configuration to your "File transfer protocols" section:
3024 Name Program Name U/D FullScr IO-Red. Multi
3025 X kermit /usr/bin/kermit -i -l %l -s Y U Y N N
3026 Y kermit /usr/bin/kermit -i -l %l -r N D Y N N
3032 Starting at version 0.9.2, U-Boot supports NetBSD both as host
3033 (build U-Boot) and target system (boots NetBSD/mpc8xx).
3035 Building requires a cross environment; it is known to work on
3036 NetBSD/i386 with the cross-powerpc-netbsd-1.3 package (you will also
3037 need gmake since the Makefiles are not compatible with BSD make).
3038 Note that the cross-powerpc package does not install include files;
3039 attempting to build U-Boot will fail because <machine/ansi.h> is
3040 missing. This file has to be installed and patched manually:
3042 # cd /usr/pkg/cross/powerpc-netbsd/include
3044 # ln -s powerpc machine
3045 # cp /usr/src/sys/arch/powerpc/include/ansi.h powerpc/ansi.h
3046 # ${EDIT} powerpc/ansi.h ## must remove __va_list, _BSD_VA_LIST
3048 Native builds *don't* work due to incompatibilities between native
3049 and U-Boot include files.
3051 Booting assumes that (the first part of) the image booted is a
3052 stage-2 loader which in turn loads and then invokes the kernel
3053 proper. Loader sources will eventually appear in the NetBSD source
3054 tree (probably in sys/arc/mpc8xx/stand/u-boot_stage2/); in the
3055 meantime, send mail to bruno@exet-ag.de and/or wd@denx.de for
3059 Implementation Internals:
3060 =========================
3062 The following is not intended to be a complete description of every
3063 implementation detail. However, it should help to understand the
3064 inner workings of U-Boot and make it easier to port it to custom
3068 Initial Stack, Global Data:
3069 ---------------------------
3071 The implementation of U-Boot is complicated by the fact that U-Boot
3072 starts running out of ROM (flash memory), usually without access to
3073 system RAM (because the memory controller is not initialized yet).
3074 This means that we don't have writable Data or BSS segments, and BSS
3075 is not initialized as zero. To be able to get a C environment working
3076 at all, we have to allocate at least a minimal stack. Implementation
3077 options for this are defined and restricted by the CPU used: Some CPU
3078 models provide on-chip memory (like the IMMR area on MPC8xx and
3079 MPC826x processors), on others (parts of) the data cache can be
3080 locked as (mis-) used as memory, etc.
3082 Chris Hallinan posted a good summary of these issues to the
3083 u-boot-users mailing list:
3085 Subject: RE: [U-Boot-Users] RE: More On Memory Bank x (nothingness)?
3086 From: "Chris Hallinan" <clh@net1plus.com>
3087 Date: Mon, 10 Feb 2003 16:43:46 -0500 (22:43 MET)
3090 Correct me if I'm wrong, folks, but the way I understand it
3091 is this: Using DCACHE as initial RAM for Stack, etc, does not
3092 require any physical RAM backing up the cache. The cleverness
3093 is that the cache is being used as a temporary supply of
3094 necessary storage before the SDRAM controller is setup. It's
3095 beyond the scope of this list to expain the details, but you
3096 can see how this works by studying the cache architecture and
3097 operation in the architecture and processor-specific manuals.
3099 OCM is On Chip Memory, which I believe the 405GP has 4K. It
3100 is another option for the system designer to use as an
3101 initial stack/ram area prior to SDRAM being available. Either
3102 option should work for you. Using CS 4 should be fine if your
3103 board designers haven't used it for something that would
3104 cause you grief during the initial boot! It is frequently not
3107 CFG_INIT_RAM_ADDR should be somewhere that won't interfere
3108 with your processor/board/system design. The default value
3109 you will find in any recent u-boot distribution in
3110 Walnut405.h should work for you. I'd set it to a value larger
3111 than your SDRAM module. If you have a 64MB SDRAM module, set
3112 it above 400_0000. Just make sure your board has no resources
3113 that are supposed to respond to that address! That code in
3114 start.S has been around a while and should work as is when
3115 you get the config right.
3120 It is essential to remember this, since it has some impact on the C
3121 code for the initialization procedures:
3123 * Initialized global data (data segment) is read-only. Do not attempt
3126 * Do not use any unitialized global data (or implicitely initialized
3127 as zero data - BSS segment) at all - this is undefined, initiali-
3128 zation is performed later (when relocating to RAM).
3130 * Stack space is very limited. Avoid big data buffers or things like
3133 Having only the stack as writable memory limits means we cannot use
3134 normal global data to share information beween the code. But it
3135 turned out that the implementation of U-Boot can be greatly
3136 simplified by making a global data structure (gd_t) available to all
3137 functions. We could pass a pointer to this data as argument to _all_
3138 functions, but this would bloat the code. Instead we use a feature of
3139 the GCC compiler (Global Register Variables) to share the data: we
3140 place a pointer (gd) to the global data into a register which we
3141 reserve for this purpose.
3143 When choosing a register for such a purpose we are restricted by the
3144 relevant (E)ABI specifications for the current architecture, and by
3145 GCC's implementation.
3147 For PowerPC, the following registers have specific use:
3150 R3-R4: parameter passing and return values
3151 R5-R10: parameter passing
3152 R13: small data area pointer
3156 (U-Boot also uses R14 as internal GOT pointer.)
3158 ==> U-Boot will use R29 to hold a pointer to the global data
3160 Note: on PPC, we could use a static initializer (since the
3161 address of the global data structure is known at compile time),
3162 but it turned out that reserving a register results in somewhat
3163 smaller code - although the code savings are not that big (on
3164 average for all boards 752 bytes for the whole U-Boot image,
3165 624 text + 127 data).
3167 On ARM, the following registers are used:
3169 R0: function argument word/integer result
3170 R1-R3: function argument word
3172 R10: stack limit (used only if stack checking if enabled)
3173 R11: argument (frame) pointer
3174 R12: temporary workspace
3177 R15: program counter
3179 ==> U-Boot will use R8 to hold a pointer to the global data
3185 U-Boot runs in system state and uses physical addresses, i.e. the
3186 MMU is not used either for address mapping nor for memory protection.
3188 The available memory is mapped to fixed addresses using the memory
3189 controller. In this process, a contiguous block is formed for each
3190 memory type (Flash, SDRAM, SRAM), even when it consists of several
3191 physical memory banks.
3193 U-Boot is installed in the first 128 kB of the first Flash bank (on
3194 TQM8xxL modules this is the range 0x40000000 ... 0x4001FFFF). After
3195 booting and sizing and initializing DRAM, the code relocates itself
3196 to the upper end of DRAM. Immediately below the U-Boot code some
3197 memory is reserved for use by malloc() [see CFG_MALLOC_LEN
3198 configuration setting]. Below that, a structure with global Board
3199 Info data is placed, followed by the stack (growing downward).
3201 Additionally, some exception handler code is copied to the low 8 kB
3202 of DRAM (0x00000000 ... 0x00001FFF).
3204 So a typical memory configuration with 16 MB of DRAM could look like
3207 0x0000 0000 Exception Vector code
3210 0x0000 2000 Free for Application Use
3216 0x00FB FF20 Monitor Stack (Growing downward)
3217 0x00FB FFAC Board Info Data and permanent copy of global data
3218 0x00FC 0000 Malloc Arena
3221 0x00FE 0000 RAM Copy of Monitor Code
3222 ... eventually: LCD or video framebuffer
3223 ... eventually: pRAM (Protected RAM - unchanged by reset)
3224 0x00FF FFFF [End of RAM]
3227 System Initialization:
3228 ----------------------
3230 In the reset configuration, U-Boot starts at the reset entry point
3231 (on most PowerPC systens at address 0x00000100). Because of the reset
3232 configuration for CS0# this is a mirror of the onboard Flash memory.
3233 To be able to re-map memory U-Boot then jumps to its link address.
3234 To be able to implement the initialization code in C, a (small!)
3235 initial stack is set up in the internal Dual Ported RAM (in case CPUs
3236 which provide such a feature like MPC8xx or MPC8260), or in a locked
3237 part of the data cache. After that, U-Boot initializes the CPU core,
3238 the caches and the SIU.
3240 Next, all (potentially) available memory banks are mapped using a
3241 preliminary mapping. For example, we put them on 512 MB boundaries
3242 (multiples of 0x20000000: SDRAM on 0x00000000 and 0x20000000, Flash
3243 on 0x40000000 and 0x60000000, SRAM on 0x80000000). Then UPM A is
3244 programmed for SDRAM access. Using the temporary configuration, a
3245 simple memory test is run that determines the size of the SDRAM
3248 When there is more than one SDRAM bank, and the banks are of
3249 different size, the largest is mapped first. For equal size, the first
3250 bank (CS2#) is mapped first. The first mapping is always for address
3251 0x00000000, with any additional banks following immediately to create
3252 contiguous memory starting from 0.
3254 Then, the monitor installs itself at the upper end of the SDRAM area
3255 and allocates memory for use by malloc() and for the global Board
3256 Info data; also, the exception vector code is copied to the low RAM
3257 pages, and the final stack is set up.
3259 Only after this relocation will you have a "normal" C environment;
3260 until that you are restricted in several ways, mostly because you are
3261 running from ROM, and because the code will have to be relocated to a
3265 U-Boot Porting Guide:
3266 ----------------------
3268 [Based on messages by Jerry Van Baren in the U-Boot-Users mailing
3272 int main (int argc, char *argv[])
3274 sighandler_t no_more_time;
3276 signal (SIGALRM, no_more_time);
3277 alarm (PROJECT_DEADLINE - toSec (3 * WEEK));
3279 if (available_money > available_manpower) {
3280 pay consultant to port U-Boot;
3284 Download latest U-Boot source;
3286 Subscribe to u-boot-users mailing list;
3289 email ("Hi, I am new to U-Boot, how do I get started?");
3293 Read the README file in the top level directory;
3294 Read http://www.denx.de/twiki/bin/view/DULG/Manual ;
3295 Read the source, Luke;
3298 if (available_money > toLocalCurrency ($2500)) {
3301 Add a lot of aggravation and time;
3304 Create your own board support subdirectory;
3306 Create your own board config file;
3310 Add / modify source code;
3314 email ("Hi, I am having problems...");
3316 Send patch file to Wolfgang;
3321 void no_more_time (int sig)
3330 All contributions to U-Boot should conform to the Linux kernel
3331 coding style; see the file "Documentation/CodingStyle" in your Linux
3332 kernel source directory.
3334 Please note that U-Boot is implemented in C (and to some small parts
3335 in Assembler); no C++ is used, so please do not use C++ style
3336 comments (//) in your code.
3338 Please also stick to the following formatting rules:
3339 - remove any trailing white space
3340 - use TAB characters for indentation, not spaces
3341 - make sure NOT to use DOS '\r\n' line feeds
3342 - do not add more than 2 empty lines to source files
3343 - do not add trailing empty lines to source files
3345 Submissions which do not conform to the standards may be returned
3346 with a request to reformat the changes.
3352 Since the number of patches for U-Boot is growing, we need to
3353 establish some rules. Submissions which do not conform to these rules
3354 may be rejected, even when they contain important and valuable stuff.
3357 When you send a patch, please include the following information with
3360 * For bug fixes: a description of the bug and how your patch fixes
3361 this bug. Please try to include a way of demonstrating that the
3362 patch actually fixes something.
3364 * For new features: a description of the feature and your
3367 * A CHANGELOG entry as plaintext (separate from the patch)
3369 * For major contributions, your entry to the CREDITS file
3371 * When you add support for a new board, don't forget to add this
3372 board to the MAKEALL script, too.
3374 * If your patch adds new configuration options, don't forget to
3375 document these in the README file.
3377 * The patch itself. If you are accessing the CVS repository use "cvs
3378 update; cvs diff -puRN"; else, use "diff -purN OLD NEW". If your
3379 version of diff does not support these options, then get the latest
3380 version of GNU diff.
3382 The current directory when running this command shall be the top
3383 level directory of the U-Boot source tree, or it's parent directory
3384 (i. e. please make sure that your patch includes sufficient
3385 directory information for the affected files).
3387 We accept patches as plain text, MIME attachments or as uuencoded
3390 * If one logical set of modifications affects or creates several
3391 files, all these changes shall be submitted in a SINGLE patch file.
3393 * Changesets that contain different, unrelated modifications shall be
3394 submitted as SEPARATE patches, one patch per changeset.
3399 * Before sending the patch, run the MAKEALL script on your patched
3400 source tree and make sure that no errors or warnings are reported
3401 for any of the boards.
3403 * Keep your modifications to the necessary minimum: A patch
3404 containing several unrelated changes or arbitrary reformats will be
3405 returned with a request to re-formatting / split it.
3407 * If you modify existing code, make sure that your new code does not
3408 add to the memory footprint of the code ;-) Small is beautiful!
3409 When adding new features, these should compile conditionally only
3410 (using #ifdef), and the resulting code with the new feature
3411 disabled must not need more memory than the old code without your
projects / kernel / u-boot.git / blob