2 # (C) Copyright 2000 - 2009
3 # Wolfgang Denk, DENX Software Engineering, wd@denx.de.
5 # See file CREDITS for list of people who contributed to this
8 # This program is free software; you can redistribute it and/or
9 # modify it under the terms of the GNU General Public License as
10 # published by the Free Software Foundation; either version 2 of
11 # the License, or (at your option) any later version.
13 # This program is distributed in the hope that it will be useful,
14 # but WITHOUT ANY WARRANTY; without even the implied warranty of
15 # MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the
16 # GNU General Public License for more details.
18 # You should have received a copy of the GNU General Public License
19 # along with this program; if not, write to the Free Software
20 # Foundation, Inc., 59 Temple Place, Suite 330, Boston,
27 This directory contains the source code for U-Boot, a boot loader for
28 Embedded boards based on PowerPC, ARM, MIPS and several other
29 processors, which can be installed in a boot ROM and used to
30 initialize and test the hardware or to download and run application
33 The development of U-Boot is closely related to Linux: some parts of
34 the source code originate in the Linux source tree, we have some
35 header files in common, and special provision has been made to
36 support booting of Linux images.
38 Some attention has been paid to make this software easily
39 configurable and extendable. For instance, all monitor commands are
40 implemented with the same call interface, so that it's very easy to
41 add new commands. Also, instead of permanently adding rarely used
42 code (for instance hardware test utilities) to the monitor, you can
43 load and run it dynamically.
49 In general, all boards for which a configuration option exists in the
50 Makefile have been tested to some extent and can be considered
51 "working". In fact, many of them are used in production systems.
53 In case of problems see the CHANGELOG and CREDITS files to find out
54 who contributed the specific port. The MAINTAINERS file lists board
61 In case you have questions about, problems with or contributions for
62 U-Boot you should send a message to the U-Boot mailing list at
63 <u-boot@lists.denx.de>. There is also an archive of previous traffic
64 on the mailing list - please search the archive before asking FAQ's.
65 Please see http://lists.denx.de/pipermail/u-boot and
66 http://dir.gmane.org/gmane.comp.boot-loaders.u-boot
69 Where to get source code:
70 =========================
72 The U-Boot source code is maintained in the git repository at
73 git://www.denx.de/git/u-boot.git ; you can browse it online at
74 http://www.denx.de/cgi-bin/gitweb.cgi?p=u-boot.git;a=summary
76 The "snapshot" links on this page allow you to download tarballs of
77 any version you might be interested in. Official releases are also
78 available for FTP download from the ftp://ftp.denx.de/pub/u-boot/
81 Pre-built (and tested) images are available from
82 ftp://ftp.denx.de/pub/u-boot/images/
88 - start from 8xxrom sources
89 - create PPCBoot project (http://sourceforge.net/projects/ppcboot)
91 - make it easier to add custom boards
92 - make it possible to add other [PowerPC] CPUs
93 - extend functions, especially:
94 * Provide extended interface to Linux boot loader
97 * PCMCIA / CompactFlash / ATA disk / SCSI ... boot
98 - create ARMBoot project (http://sourceforge.net/projects/armboot)
99 - add other CPU families (starting with ARM)
100 - create U-Boot project (http://sourceforge.net/projects/u-boot)
101 - current project page: see http://www.denx.de/wiki/U-Boot
107 The "official" name of this project is "Das U-Boot". The spelling
108 "U-Boot" shall be used in all written text (documentation, comments
109 in source files etc.). Example:
111 This is the README file for the U-Boot project.
113 File names etc. shall be based on the string "u-boot". Examples:
115 include/asm-ppc/u-boot.h
117 #include <asm/u-boot.h>
119 Variable names, preprocessor constants etc. shall be either based on
120 the string "u_boot" or on "U_BOOT". Example:
122 U_BOOT_VERSION u_boot_logo
123 IH_OS_U_BOOT u_boot_hush_start
129 U-Boot uses a 3 level version number containing a version, a
130 sub-version, and a patchlevel: "U-Boot-2.34.5" means version "2",
131 sub-version "34", and patchlevel "4".
133 The patchlevel is used to indicate certain stages of development
134 between released versions, i. e. officially released versions of
135 U-Boot will always have a patchlevel of "0".
141 /arch Architecture specific files
142 /arm Files generic to ARM architecture
143 /cpu CPU specific files
144 /arm720t Files specific to ARM 720 CPUs
145 /arm920t Files specific to ARM 920 CPUs
146 /at91rm9200 Files specific to Atmel AT91RM9200 CPU
147 /imx Files specific to Freescale MC9328 i.MX CPUs
148 /s3c24x0 Files specific to Samsung S3C24X0 CPUs
149 /arm925t Files specific to ARM 925 CPUs
150 /arm926ejs Files specific to ARM 926 CPUs
151 /arm1136 Files specific to ARM 1136 CPUs
152 /ixp Files specific to Intel XScale IXP CPUs
153 /pxa Files specific to Intel XScale PXA CPUs
154 /s3c44b0 Files specific to Samsung S3C44B0 CPUs
155 /sa1100 Files specific to Intel StrongARM SA1100 CPUs
156 /lib Architecture specific library files
157 /avr32 Files generic to AVR32 architecture
158 /cpu CPU specific files
159 /lib Architecture specific library files
160 /blackfin Files generic to Analog Devices Blackfin architecture
161 /cpu CPU specific files
162 /lib Architecture specific library files
163 /i386 Files generic to i386 architecture
164 /cpu CPU specific files
165 /lib Architecture specific library files
166 /m68k Files generic to m68k architecture
167 /cpu CPU specific files
168 /mcf52x2 Files specific to Freescale ColdFire MCF52x2 CPUs
169 /mcf5227x Files specific to Freescale ColdFire MCF5227x CPUs
170 /mcf532x Files specific to Freescale ColdFire MCF5329 CPUs
171 /mcf5445x Files specific to Freescale ColdFire MCF5445x CPUs
172 /mcf547x_8x Files specific to Freescale ColdFire MCF547x_8x CPUs
173 /lib Architecture specific library files
174 /microblaze Files generic to microblaze architecture
175 /cpu CPU specific files
176 /lib Architecture specific library files
177 /mips Files generic to MIPS architecture
178 /cpu CPU specific files
179 /lib Architecture specific library files
180 /nios2 Files generic to Altera NIOS2 architecture
181 /cpu CPU specific files
182 /lib Architecture specific library files
183 /powerpc Files generic to PowerPC architecture
184 /cpu CPU specific files
185 /74xx_7xx Files specific to Freescale MPC74xx and 7xx CPUs
186 /mpc5xx Files specific to Freescale MPC5xx CPUs
187 /mpc5xxx Files specific to Freescale MPC5xxx CPUs
188 /mpc8xx Files specific to Freescale MPC8xx CPUs
189 /mpc8220 Files specific to Freescale MPC8220 CPUs
190 /mpc824x Files specific to Freescale MPC824x CPUs
191 /mpc8260 Files specific to Freescale MPC8260 CPUs
192 /mpc85xx Files specific to Freescale MPC85xx CPUs
193 /ppc4xx Files specific to AMCC PowerPC 4xx CPUs
194 /lib Architecture specific library files
195 /sh Files generic to SH architecture
196 /cpu CPU specific files
197 /sh2 Files specific to sh2 CPUs
198 /sh3 Files specific to sh3 CPUs
199 /sh4 Files specific to sh4 CPUs
200 /lib Architecture specific library files
201 /sparc Files generic to SPARC architecture
202 /cpu CPU specific files
203 /leon2 Files specific to Gaisler LEON2 SPARC CPU
204 /leon3 Files specific to Gaisler LEON3 SPARC CPU
205 /lib Architecture specific library files
206 /api Machine/arch independent API for external apps
207 /board Board dependent files
208 /common Misc architecture independent functions
209 /disk Code for disk drive partition handling
210 /doc Documentation (don't expect too much)
211 /drivers Commonly used device drivers
212 /examples Example code for standalone applications, etc.
213 /fs Filesystem code (cramfs, ext2, jffs2, etc.)
214 /include Header Files
215 /lib Files generic to all architectures
216 /libfdt Library files to support flattened device trees
217 /lzma Library files to support LZMA decompression
218 /lzo Library files to support LZO decompression
220 /post Power On Self Test
221 /rtc Real Time Clock drivers
222 /tools Tools to build S-Record or U-Boot images, etc.
224 Software Configuration:
225 =======================
227 Configuration is usually done using C preprocessor defines; the
228 rationale behind that is to avoid dead code whenever possible.
230 There are two classes of configuration variables:
232 * Configuration _OPTIONS_:
233 These are selectable by the user and have names beginning with
236 * Configuration _SETTINGS_:
237 These depend on the hardware etc. and should not be meddled with if
238 you don't know what you're doing; they have names beginning with
241 Later we will add a configuration tool - probably similar to or even
242 identical to what's used for the Linux kernel. Right now, we have to
243 do the configuration by hand, which means creating some symbolic
244 links and editing some configuration files. We use the TQM8xxL boards
248 Selection of Processor Architecture and Board Type:
249 ---------------------------------------------------
251 For all supported boards there are ready-to-use default
252 configurations available; just type "make <board_name>_config".
254 Example: For a TQM823L module type:
259 For the Cogent platform, you need to specify the CPU type as well;
260 e.g. "make cogent_mpc8xx_config". And also configure the cogent
261 directory according to the instructions in cogent/README.
264 Configuration Options:
265 ----------------------
267 Configuration depends on the combination of board and CPU type; all
268 such information is kept in a configuration file
269 "include/configs/<board_name>.h".
271 Example: For a TQM823L module, all configuration settings are in
272 "include/configs/TQM823L.h".
275 Many of the options are named exactly as the corresponding Linux
276 kernel configuration options. The intention is to make it easier to
277 build a config tool - later.
280 The following options need to be configured:
282 - CPU Type: Define exactly one, e.g. CONFIG_MPC85XX.
284 - Board Type: Define exactly one, e.g. CONFIG_MPC8540ADS.
286 - CPU Daughterboard Type: (if CONFIG_ATSTK1000 is defined)
287 Define exactly one, e.g. CONFIG_ATSTK1002
289 - CPU Module Type: (if CONFIG_COGENT is defined)
290 Define exactly one of
292 --- FIXME --- not tested yet:
293 CONFIG_CMA286_60, CONFIG_CMA286_21, CONFIG_CMA286_60P,
294 CONFIG_CMA287_23, CONFIG_CMA287_50
296 - Motherboard Type: (if CONFIG_COGENT is defined)
297 Define exactly one of
298 CONFIG_CMA101, CONFIG_CMA102
300 - Motherboard I/O Modules: (if CONFIG_COGENT is defined)
301 Define one or more of
304 - Motherboard Options: (if CONFIG_CMA101 or CONFIG_CMA102 are defined)
305 Define one or more of
306 CONFIG_LCD_HEARTBEAT - update a character position on
307 the LCD display every second with
310 - Board flavour: (if CONFIG_MPC8260ADS is defined)
313 CONFIG_SYS_8260ADS - original MPC8260ADS
314 CONFIG_SYS_8266ADS - MPC8266ADS
315 CONFIG_SYS_PQ2FADS - PQ2FADS-ZU or PQ2FADS-VR
316 CONFIG_SYS_8272ADS - MPC8272ADS
318 - MPC824X Family Member (if CONFIG_MPC824X is defined)
319 Define exactly one of
320 CONFIG_MPC8240, CONFIG_MPC8245
322 - 8xx CPU Options: (if using an MPC8xx CPU)
323 CONFIG_8xx_GCLK_FREQ - deprecated: CPU clock if
324 get_gclk_freq() cannot work
325 e.g. if there is no 32KHz
326 reference PIT/RTC clock
327 CONFIG_8xx_OSCLK - PLL input clock (either EXTCLK
330 - 859/866/885 CPU options: (if using a MPC859 or MPC866 or MPC885 CPU):
331 CONFIG_SYS_8xx_CPUCLK_MIN
332 CONFIG_SYS_8xx_CPUCLK_MAX
333 CONFIG_8xx_CPUCLK_DEFAULT
334 See doc/README.MPC866
336 CONFIG_SYS_MEASURE_CPUCLK
338 Define this to measure the actual CPU clock instead
339 of relying on the correctness of the configured
340 values. Mostly useful for board bringup to make sure
341 the PLL is locked at the intended frequency. Note
342 that this requires a (stable) reference clock (32 kHz
343 RTC clock or CONFIG_SYS_8XX_XIN)
345 CONFIG_SYS_DELAYED_ICACHE
347 Define this option if you want to enable the
348 ICache only when Code runs from RAM.
350 - Intel Monahans options:
351 CONFIG_SYS_MONAHANS_RUN_MODE_OSC_RATIO
353 Defines the Monahans run mode to oscillator
354 ratio. Valid values are 8, 16, 24, 31. The core
355 frequency is this value multiplied by 13 MHz.
357 CONFIG_SYS_MONAHANS_TURBO_RUN_MODE_RATIO
359 Defines the Monahans turbo mode to oscillator
360 ratio. Valid values are 1 (default if undefined) and
361 2. The core frequency as calculated above is multiplied
364 - Linux Kernel Interface:
367 U-Boot stores all clock information in Hz
368 internally. For binary compatibility with older Linux
369 kernels (which expect the clocks passed in the
370 bd_info data to be in MHz) the environment variable
371 "clocks_in_mhz" can be defined so that U-Boot
372 converts clock data to MHZ before passing it to the
374 When CONFIG_CLOCKS_IN_MHZ is defined, a definition of
375 "clocks_in_mhz=1" is automatically included in the
378 CONFIG_MEMSIZE_IN_BYTES [relevant for MIPS only]
380 When transferring memsize parameter to linux, some versions
381 expect it to be in bytes, others in MB.
382 Define CONFIG_MEMSIZE_IN_BYTES to make it in bytes.
386 New kernel versions are expecting firmware settings to be
387 passed using flattened device trees (based on open firmware
391 * New libfdt-based support
392 * Adds the "fdt" command
393 * The bootm command automatically updates the fdt
395 OF_CPU - The proper name of the cpus node (only required for
396 MPC512X and MPC5xxx based boards).
397 OF_SOC - The proper name of the soc node (only required for
398 MPC512X and MPC5xxx based boards).
399 OF_TBCLK - The timebase frequency.
400 OF_STDOUT_PATH - The path to the console device
402 boards with QUICC Engines require OF_QE to set UCC MAC
405 CONFIG_OF_BOARD_SETUP
407 Board code has addition modification that it wants to make
408 to the flat device tree before handing it off to the kernel
412 This define fills in the correct boot CPU in the boot
413 param header, the default value is zero if undefined.
417 U-Boot can detect if an IDE device is present or not.
418 If not, and this new config option is activated, U-Boot
419 removes the ATA node from the DTS before booting Linux,
420 so the Linux IDE driver does not probe the device and
421 crash. This is needed for buggy hardware (uc101) where
422 no pull down resistor is connected to the signal IDE5V_DD7.
424 - vxWorks boot parameters:
426 bootvx constructs a valid bootline using the following
427 environments variables: bootfile, ipaddr, serverip, hostname.
428 It loads the vxWorks image pointed bootfile.
430 CONFIG_SYS_VXWORKS_BOOT_DEVICE - The vxworks device name
431 CONFIG_SYS_VXWORKS_MAC_PTR - Ethernet 6 byte MA -address
432 CONFIG_SYS_VXWORKS_SERVERNAME - Name of the server
433 CONFIG_SYS_VXWORKS_BOOT_ADDR - Address of boot parameters
435 CONFIG_SYS_VXWORKS_ADD_PARAMS
437 Add it at the end of the bootline. E.g "u=username pw=secret"
439 Note: If a "bootargs" environment is defined, it will overwride
440 the defaults discussed just above.
445 Define this if you want support for Amba PrimeCell PL010 UARTs.
449 Define this if you want support for Amba PrimeCell PL011 UARTs.
453 If you have Amba PrimeCell PL011 UARTs, set this variable to
454 the clock speed of the UARTs.
458 If you have Amba PrimeCell PL010 or PL011 UARTs on your board,
459 define this to a list of base addresses for each (supported)
460 port. See e.g. include/configs/versatile.h
464 Depending on board, define exactly one serial port
465 (like CONFIG_8xx_CONS_SMC1, CONFIG_8xx_CONS_SMC2,
466 CONFIG_8xx_CONS_SCC1, ...), or switch off the serial
467 console by defining CONFIG_8xx_CONS_NONE
469 Note: if CONFIG_8xx_CONS_NONE is defined, the serial
470 port routines must be defined elsewhere
471 (i.e. serial_init(), serial_getc(), ...)
474 Enables console device for a color framebuffer. Needs following
475 defines (cf. smiLynxEM, i8042, board/eltec/bab7xx)
476 VIDEO_FB_LITTLE_ENDIAN graphic memory organisation
478 VIDEO_HW_RECTFILL graphic chip supports
481 VIDEO_HW_BITBLT graphic chip supports
482 bit-blit (cf. smiLynxEM)
483 VIDEO_VISIBLE_COLS visible pixel columns
485 VIDEO_VISIBLE_ROWS visible pixel rows
486 VIDEO_PIXEL_SIZE bytes per pixel
487 VIDEO_DATA_FORMAT graphic data format
488 (0-5, cf. cfb_console.c)
489 VIDEO_FB_ADRS framebuffer address
490 VIDEO_KBD_INIT_FCT keyboard int fct
491 (i.e. i8042_kbd_init())
492 VIDEO_TSTC_FCT test char fct
494 VIDEO_GETC_FCT get char fct
496 CONFIG_CONSOLE_CURSOR cursor drawing on/off
497 (requires blink timer
499 CONFIG_SYS_CONSOLE_BLINK_COUNT blink interval (cf. i8042.c)
500 CONFIG_CONSOLE_TIME display time/date info in
502 (requires CONFIG_CMD_DATE)
503 CONFIG_VIDEO_LOGO display Linux logo in
505 CONFIG_VIDEO_BMP_LOGO use bmp_logo.h instead of
506 linux_logo.h for logo.
507 Requires CONFIG_VIDEO_LOGO
508 CONFIG_CONSOLE_EXTRA_INFO
509 additional board info beside
512 When CONFIG_CFB_CONSOLE is defined, video console is
513 default i/o. Serial console can be forced with
514 environment 'console=serial'.
516 When CONFIG_SILENT_CONSOLE is defined, all console
517 messages (by U-Boot and Linux!) can be silenced with
518 the "silent" environment variable. See
519 doc/README.silent for more information.
522 CONFIG_BAUDRATE - in bps
523 Select one of the baudrates listed in
524 CONFIG_SYS_BAUDRATE_TABLE, see below.
525 CONFIG_SYS_BRGCLK_PRESCALE, baudrate prescale
527 - Console Rx buffer length
528 With CONFIG_SYS_SMC_RXBUFLEN it is possible to define
529 the maximum receive buffer length for the SMC.
530 This option is actual only for 82xx and 8xx possible.
531 If using CONFIG_SYS_SMC_RXBUFLEN also CONFIG_SYS_MAXIDLE
532 must be defined, to setup the maximum idle timeout for
535 - Interrupt driven serial port input:
536 CONFIG_SERIAL_SOFTWARE_FIFO
539 Use an interrupt handler for receiving data on the
540 serial port. It also enables using hardware handshake
541 (RTS/CTS) and UART's built-in FIFO. Set the number of
542 bytes the interrupt driven input buffer should have.
544 Leave undefined to disable this feature, including
545 disable the buffer and hardware handshake.
547 - Console UART Number:
551 If defined internal UART1 (and not UART0) is used
552 as default U-Boot console.
554 - Boot Delay: CONFIG_BOOTDELAY - in seconds
555 Delay before automatically booting the default image;
556 set to -1 to disable autoboot.
558 See doc/README.autoboot for these options that
559 work with CONFIG_BOOTDELAY. None are required.
560 CONFIG_BOOT_RETRY_TIME
561 CONFIG_BOOT_RETRY_MIN
562 CONFIG_AUTOBOOT_KEYED
563 CONFIG_AUTOBOOT_PROMPT
564 CONFIG_AUTOBOOT_DELAY_STR
565 CONFIG_AUTOBOOT_STOP_STR
566 CONFIG_AUTOBOOT_DELAY_STR2
567 CONFIG_AUTOBOOT_STOP_STR2
568 CONFIG_ZERO_BOOTDELAY_CHECK
569 CONFIG_RESET_TO_RETRY
573 Only needed when CONFIG_BOOTDELAY is enabled;
574 define a command string that is automatically executed
575 when no character is read on the console interface
576 within "Boot Delay" after reset.
579 This can be used to pass arguments to the bootm
580 command. The value of CONFIG_BOOTARGS goes into the
581 environment value "bootargs".
583 CONFIG_RAMBOOT and CONFIG_NFSBOOT
584 The value of these goes into the environment as
585 "ramboot" and "nfsboot" respectively, and can be used
586 as a convenience, when switching between booting from
592 When this option is #defined, the existence of the
593 environment variable "preboot" will be checked
594 immediately before starting the CONFIG_BOOTDELAY
595 countdown and/or running the auto-boot command resp.
596 entering interactive mode.
598 This feature is especially useful when "preboot" is
599 automatically generated or modified. For an example
600 see the LWMON board specific code: here "preboot" is
601 modified when the user holds down a certain
602 combination of keys on the (special) keyboard when
605 - Serial Download Echo Mode:
607 If defined to 1, all characters received during a
608 serial download (using the "loads" command) are
609 echoed back. This might be needed by some terminal
610 emulations (like "cu"), but may as well just take
611 time on others. This setting #define's the initial
612 value of the "loads_echo" environment variable.
614 - Kgdb Serial Baudrate: (if CONFIG_CMD_KGDB is defined)
616 Select one of the baudrates listed in
617 CONFIG_SYS_BAUDRATE_TABLE, see below.
620 Monitor commands can be included or excluded
621 from the build by using the #include files
622 "config_cmd_all.h" and #undef'ing unwanted
623 commands, or using "config_cmd_default.h"
624 and augmenting with additional #define's
627 The default command configuration includes all commands
628 except those marked below with a "*".
630 CONFIG_CMD_ASKENV * ask for env variable
631 CONFIG_CMD_BDI bdinfo
632 CONFIG_CMD_BEDBUG * Include BedBug Debugger
633 CONFIG_CMD_BMP * BMP support
634 CONFIG_CMD_BSP * Board specific commands
635 CONFIG_CMD_BOOTD bootd
636 CONFIG_CMD_CACHE * icache, dcache
637 CONFIG_CMD_CONSOLE coninfo
638 CONFIG_CMD_DATE * support for RTC, date/time...
639 CONFIG_CMD_DHCP * DHCP support
640 CONFIG_CMD_DIAG * Diagnostics
641 CONFIG_CMD_DS4510 * ds4510 I2C gpio commands
642 CONFIG_CMD_DS4510_INFO * ds4510 I2C info command
643 CONFIG_CMD_DS4510_MEM * ds4510 I2C eeprom/sram commansd
644 CONFIG_CMD_DS4510_RST * ds4510 I2C rst command
645 CONFIG_CMD_DTT * Digital Therm and Thermostat
646 CONFIG_CMD_ECHO echo arguments
647 CONFIG_CMD_EDITENV edit env variable
648 CONFIG_CMD_EEPROM * EEPROM read/write support
649 CONFIG_CMD_ELF * bootelf, bootvx
650 CONFIG_CMD_SAVEENV saveenv
651 CONFIG_CMD_FDC * Floppy Disk Support
652 CONFIG_CMD_FAT * FAT partition support
653 CONFIG_CMD_FDOS * Dos diskette Support
654 CONFIG_CMD_FLASH flinfo, erase, protect
655 CONFIG_CMD_FPGA FPGA device initialization support
656 CONFIG_CMD_HWFLOW * RTS/CTS hw flow control
657 CONFIG_CMD_I2C * I2C serial bus support
658 CONFIG_CMD_IDE * IDE harddisk support
659 CONFIG_CMD_IMI iminfo
660 CONFIG_CMD_IMLS List all found images
661 CONFIG_CMD_IMMAP * IMMR dump support
662 CONFIG_CMD_IRQ * irqinfo
663 CONFIG_CMD_ITEST Integer/string test of 2 values
664 CONFIG_CMD_JFFS2 * JFFS2 Support
665 CONFIG_CMD_KGDB * kgdb
666 CONFIG_CMD_LOADB loadb
667 CONFIG_CMD_LOADS loads
668 CONFIG_CMD_MD5SUM print md5 message digest
669 (requires CONFIG_CMD_MEMORY and CONFIG_MD5)
670 CONFIG_CMD_MEMORY md, mm, nm, mw, cp, cmp, crc, base,
672 CONFIG_CMD_MISC Misc functions like sleep etc
673 CONFIG_CMD_MMC * MMC memory mapped support
674 CONFIG_CMD_MII * MII utility commands
675 CONFIG_CMD_MTDPARTS * MTD partition support
676 CONFIG_CMD_NAND * NAND support
677 CONFIG_CMD_NET bootp, tftpboot, rarpboot
678 CONFIG_CMD_PCA953X * PCA953x I2C gpio commands
679 CONFIG_CMD_PCA953X_INFO * PCA953x I2C gpio info command
680 CONFIG_CMD_PCI * pciinfo
681 CONFIG_CMD_PCMCIA * PCMCIA support
682 CONFIG_CMD_PING * send ICMP ECHO_REQUEST to network
684 CONFIG_CMD_PORTIO * Port I/O
685 CONFIG_CMD_REGINFO * Register dump
686 CONFIG_CMD_RUN run command in env variable
687 CONFIG_CMD_SAVES * save S record dump
688 CONFIG_CMD_SCSI * SCSI Support
689 CONFIG_CMD_SDRAM * print SDRAM configuration information
690 (requires CONFIG_CMD_I2C)
691 CONFIG_CMD_SETGETDCR Support for DCR Register access
693 CONFIG_CMD_SHA1 print sha1 memory digest
694 (requires CONFIG_CMD_MEMORY)
695 CONFIG_CMD_SOURCE "source" command Support
696 CONFIG_CMD_SPI * SPI serial bus support
697 CONFIG_CMD_USB * USB support
698 CONFIG_CMD_VFD * VFD support (TRAB)
699 CONFIG_CMD_CDP * Cisco Discover Protocol support
700 CONFIG_CMD_FSL * Microblaze FSL support
703 EXAMPLE: If you want all functions except of network
704 support you can write:
706 #include "config_cmd_all.h"
707 #undef CONFIG_CMD_NET
710 fdt (flattened device tree) command: CONFIG_OF_LIBFDT
712 Note: Don't enable the "icache" and "dcache" commands
713 (configuration option CONFIG_CMD_CACHE) unless you know
714 what you (and your U-Boot users) are doing. Data
715 cache cannot be enabled on systems like the 8xx or
716 8260 (where accesses to the IMMR region must be
717 uncached), and it cannot be disabled on all other
718 systems where we (mis-) use the data cache to hold an
719 initial stack and some data.
722 XXX - this list needs to get updated!
726 If this variable is defined, it enables watchdog
727 support. There must be support in the platform specific
728 code for a watchdog. For the 8xx and 8260 CPUs, the
729 SIU Watchdog feature is enabled in the SYPCR
733 CONFIG_VERSION_VARIABLE
734 If this variable is defined, an environment variable
735 named "ver" is created by U-Boot showing the U-Boot
736 version as printed by the "version" command.
737 This variable is readonly.
741 When CONFIG_CMD_DATE is selected, the type of the RTC
742 has to be selected, too. Define exactly one of the
745 CONFIG_RTC_MPC8xx - use internal RTC of MPC8xx
746 CONFIG_RTC_PCF8563 - use Philips PCF8563 RTC
747 CONFIG_RTC_MC13783 - use MC13783 RTC
748 CONFIG_RTC_MC146818 - use MC146818 RTC
749 CONFIG_RTC_DS1307 - use Maxim, Inc. DS1307 RTC
750 CONFIG_RTC_DS1337 - use Maxim, Inc. DS1337 RTC
751 CONFIG_RTC_DS1338 - use Maxim, Inc. DS1338 RTC
752 CONFIG_RTC_DS164x - use Dallas DS164x RTC
753 CONFIG_RTC_ISL1208 - use Intersil ISL1208 RTC
754 CONFIG_RTC_MAX6900 - use Maxim, Inc. MAX6900 RTC
755 CONFIG_SYS_RTC_DS1337_NOOSC - Turn off the OSC output for DS1337
757 Note that if the RTC uses I2C, then the I2C interface
758 must also be configured. See I2C Support, below.
761 CONFIG_PCA953X - use NXP's PCA953X series I2C GPIO
762 CONFIG_PCA953X_INFO - enable pca953x info command
764 Note that if the GPIO device uses I2C, then the I2C interface
765 must also be configured. See I2C Support, below.
769 When CONFIG_TIMESTAMP is selected, the timestamp
770 (date and time) of an image is printed by image
771 commands like bootm or iminfo. This option is
772 automatically enabled when you select CONFIG_CMD_DATE .
775 CONFIG_MAC_PARTITION and/or CONFIG_DOS_PARTITION
776 and/or CONFIG_ISO_PARTITION and/or CONFIG_EFI_PARTITION
778 If IDE or SCSI support is enabled (CONFIG_CMD_IDE or
779 CONFIG_CMD_SCSI) you must configure support for at
780 least one partition type as well.
783 CONFIG_IDE_RESET_ROUTINE - this is defined in several
784 board configurations files but used nowhere!
786 CONFIG_IDE_RESET - is this is defined, IDE Reset will
787 be performed by calling the function
788 ide_set_reset(int reset)
789 which has to be defined in a board specific file
794 Set this to enable ATAPI support.
799 Set this to enable support for disks larger than 137GB
800 Also look at CONFIG_SYS_64BIT_LBA.
801 Whithout these , LBA48 support uses 32bit variables and will 'only'
802 support disks up to 2.1TB.
804 CONFIG_SYS_64BIT_LBA:
805 When enabled, makes the IDE subsystem use 64bit sector addresses.
809 At the moment only there is only support for the
810 SYM53C8XX SCSI controller; define
811 CONFIG_SCSI_SYM53C8XX to enable it.
813 CONFIG_SYS_SCSI_MAX_LUN [8], CONFIG_SYS_SCSI_MAX_SCSI_ID [7] and
814 CONFIG_SYS_SCSI_MAX_DEVICE [CONFIG_SYS_SCSI_MAX_SCSI_ID *
815 CONFIG_SYS_SCSI_MAX_LUN] can be adjusted to define the
816 maximum numbers of LUNs, SCSI ID's and target
818 CONFIG_SYS_SCSI_SYM53C8XX_CCF to fix clock timing (80Mhz)
820 - NETWORK Support (PCI):
822 Support for Intel 8254x gigabit chips.
824 CONFIG_E1000_FALLBACK_MAC
825 default MAC for empty EEPROM after production.
828 Support for Intel 82557/82559/82559ER chips.
829 Optional CONFIG_EEPRO100_SROM_WRITE enables EEPROM
830 write routine for first time initialisation.
833 Support for Digital 2114x chips.
834 Optional CONFIG_TULIP_SELECT_MEDIA for board specific
835 modem chip initialisation (KS8761/QS6611).
838 Support for National dp83815 chips.
841 Support for National dp8382[01] gigabit chips.
843 - NETWORK Support (other):
845 CONFIG_DRIVER_AT91EMAC
846 Support for AT91RM9200 EMAC.
849 Define this to use reduced MII inteface
851 CONFIG_DRIVER_AT91EMAC_QUIET
852 If this defined, the driver is quiet.
853 The driver doen't show link status messages.
855 CONFIG_DRIVER_LAN91C96
856 Support for SMSC's LAN91C96 chips.
859 Define this to hold the physical address
860 of the LAN91C96's I/O space
862 CONFIG_LAN91C96_USE_32_BIT
863 Define this to enable 32 bit addressing
865 CONFIG_DRIVER_SMC91111
866 Support for SMSC's LAN91C111 chip
869 Define this to hold the physical address
870 of the device (I/O space)
872 CONFIG_SMC_USE_32_BIT
873 Define this if data bus is 32 bits
875 CONFIG_SMC_USE_IOFUNCS
876 Define this to use i/o functions instead of macros
877 (some hardware wont work with macros)
880 Support for SMSC's LAN911x and LAN921x chips
883 Define this to hold the physical address
884 of the device (I/O space)
886 CONFIG_SMC911X_32_BIT
887 Define this if data bus is 32 bits
889 CONFIG_SMC911X_16_BIT
890 Define this if data bus is 16 bits. If your processor
891 automatically converts one 32 bit word to two 16 bit
892 words you may also try CONFIG_SMC911X_32_BIT.
895 At the moment only the UHCI host controller is
896 supported (PIP405, MIP405, MPC5200); define
897 CONFIG_USB_UHCI to enable it.
898 define CONFIG_USB_KEYBOARD to enable the USB Keyboard
899 and define CONFIG_USB_STORAGE to enable the USB
902 Supported are USB Keyboards and USB Floppy drives
904 MPC5200 USB requires additional defines:
906 for 528 MHz Clock: 0x0001bbbb
910 for differential drivers: 0x00001000
911 for single ended drivers: 0x00005000
912 for differential drivers on PSC3: 0x00000100
913 for single ended drivers on PSC3: 0x00004100
914 CONFIG_SYS_USB_EVENT_POLL
915 May be defined to allow interrupt polling
916 instead of using asynchronous interrupts
919 Define the below if you wish to use the USB console.
920 Once firmware is rebuilt from a serial console issue the
921 command "setenv stdin usbtty; setenv stdout usbtty" and
922 attach your USB cable. The Unix command "dmesg" should print
923 it has found a new device. The environment variable usbtty
924 can be set to gserial or cdc_acm to enable your device to
925 appear to a USB host as a Linux gserial device or a
926 Common Device Class Abstract Control Model serial device.
927 If you select usbtty = gserial you should be able to enumerate
929 # modprobe usbserial vendor=0xVendorID product=0xProductID
930 else if using cdc_acm, simply setting the environment
931 variable usbtty to be cdc_acm should suffice. The following
932 might be defined in YourBoardName.h
935 Define this to build a UDC device
938 Define this to have a tty type of device available to
939 talk to the UDC device
941 CONFIG_SYS_CONSOLE_IS_IN_ENV
942 Define this if you want stdin, stdout &/or stderr to
946 CONFIG_SYS_USB_EXTC_CLK 0xBLAH
947 Derive USB clock from external clock "blah"
948 - CONFIG_SYS_USB_EXTC_CLK 0x02
950 CONFIG_SYS_USB_BRG_CLK 0xBLAH
951 Derive USB clock from brgclk
952 - CONFIG_SYS_USB_BRG_CLK 0x04
954 If you have a USB-IF assigned VendorID then you may wish to
955 define your own vendor specific values either in BoardName.h
956 or directly in usbd_vendor_info.h. If you don't define
957 CONFIG_USBD_MANUFACTURER, CONFIG_USBD_PRODUCT_NAME,
958 CONFIG_USBD_VENDORID and CONFIG_USBD_PRODUCTID, then U-Boot
959 should pretend to be a Linux device to it's target host.
961 CONFIG_USBD_MANUFACTURER
962 Define this string as the name of your company for
963 - CONFIG_USBD_MANUFACTURER "my company"
965 CONFIG_USBD_PRODUCT_NAME
966 Define this string as the name of your product
967 - CONFIG_USBD_PRODUCT_NAME "acme usb device"
970 Define this as your assigned Vendor ID from the USB
971 Implementors Forum. This *must* be a genuine Vendor ID
972 to avoid polluting the USB namespace.
973 - CONFIG_USBD_VENDORID 0xFFFF
975 CONFIG_USBD_PRODUCTID
976 Define this as the unique Product ID
978 - CONFIG_USBD_PRODUCTID 0xFFFF
982 The MMC controller on the Intel PXA is supported. To
983 enable this define CONFIG_MMC. The MMC can be
984 accessed from the boot prompt by mapping the device
985 to physical memory similar to flash. Command line is
986 enabled with CONFIG_CMD_MMC. The MMC driver also works with
987 the FAT fs. This is enabled with CONFIG_CMD_FAT.
989 - Journaling Flash filesystem support:
990 CONFIG_JFFS2_NAND, CONFIG_JFFS2_NAND_OFF, CONFIG_JFFS2_NAND_SIZE,
991 CONFIG_JFFS2_NAND_DEV
992 Define these for a default partition on a NAND device
994 CONFIG_SYS_JFFS2_FIRST_SECTOR,
995 CONFIG_SYS_JFFS2_FIRST_BANK, CONFIG_SYS_JFFS2_NUM_BANKS
996 Define these for a default partition on a NOR device
998 CONFIG_SYS_JFFS_CUSTOM_PART
999 Define this to create an own partition. You have to provide a
1000 function struct part_info* jffs2_part_info(int part_num)
1002 If you define only one JFFS2 partition you may also want to
1003 #define CONFIG_SYS_JFFS_SINGLE_PART 1
1004 to disable the command chpart. This is the default when you
1005 have not defined a custom partition
1010 Define this to enable standard (PC-Style) keyboard
1014 Standard PC keyboard driver with US (is default) and
1015 GERMAN key layout (switch via environment 'keymap=de') support.
1016 Export function i8042_kbd_init, i8042_tstc and i8042_getc
1017 for cfb_console. Supports cursor blinking.
1022 Define this to enable video support (for output to
1025 CONFIG_VIDEO_CT69000
1027 Enable Chips & Technologies 69000 Video chip
1029 CONFIG_VIDEO_SMI_LYNXEM
1030 Enable Silicon Motion SMI 712/710/810 Video chip. The
1031 video output is selected via environment 'videoout'
1032 (1 = LCD and 2 = CRT). If videoout is undefined, CRT is
1035 For the CT69000 and SMI_LYNXEM drivers, videomode is
1036 selected via environment 'videomode'. Two different ways
1038 - "videomode=num" 'num' is a standard LiLo mode numbers.
1039 Following standard modes are supported (* is default):
1041 Colors 640x480 800x600 1024x768 1152x864 1280x1024
1042 -------------+---------------------------------------------
1043 8 bits | 0x301* 0x303 0x305 0x161 0x307
1044 15 bits | 0x310 0x313 0x316 0x162 0x319
1045 16 bits | 0x311 0x314 0x317 0x163 0x31A
1046 24 bits | 0x312 0x315 0x318 ? 0x31B
1047 -------------+---------------------------------------------
1048 (i.e. setenv videomode 317; saveenv; reset;)
1050 - "videomode=bootargs" all the video parameters are parsed
1051 from the bootargs. (See drivers/video/videomodes.c)
1054 CONFIG_VIDEO_SED13806
1055 Enable Epson SED13806 driver. This driver supports 8bpp
1056 and 16bpp modes defined by CONFIG_VIDEO_SED13806_8BPP
1057 or CONFIG_VIDEO_SED13806_16BPP
1062 Define this to enable a custom keyboard support.
1063 This simply calls drv_keyboard_init() which must be
1064 defined in your board-specific files.
1065 The only board using this so far is RBC823.
1067 - LCD Support: CONFIG_LCD
1069 Define this to enable LCD support (for output to LCD
1070 display); also select one of the supported displays
1071 by defining one of these:
1075 HITACHI TX09D70VM1CCA, 3.5", 240x320.
1077 CONFIG_NEC_NL6448AC33:
1079 NEC NL6448AC33-18. Active, color, single scan.
1081 CONFIG_NEC_NL6448BC20
1083 NEC NL6448BC20-08. 6.5", 640x480.
1084 Active, color, single scan.
1086 CONFIG_NEC_NL6448BC33_54
1088 NEC NL6448BC33-54. 10.4", 640x480.
1089 Active, color, single scan.
1093 Sharp 320x240. Active, color, single scan.
1094 It isn't 16x9, and I am not sure what it is.
1096 CONFIG_SHARP_LQ64D341
1098 Sharp LQ64D341 display, 640x480.
1099 Active, color, single scan.
1103 HLD1045 display, 640x480.
1104 Active, color, single scan.
1108 Optrex CBL50840-2 NF-FW 99 22 M5
1110 Hitachi LMG6912RPFC-00T
1114 320x240. Black & white.
1116 Normally display is black on white background; define
1117 CONFIG_SYS_WHITE_ON_BLACK to get it inverted.
1119 - Splash Screen Support: CONFIG_SPLASH_SCREEN
1121 If this option is set, the environment is checked for
1122 a variable "splashimage". If found, the usual display
1123 of logo, copyright and system information on the LCD
1124 is suppressed and the BMP image at the address
1125 specified in "splashimage" is loaded instead. The
1126 console is redirected to the "nulldev", too. This
1127 allows for a "silent" boot where a splash screen is
1128 loaded very quickly after power-on.
1130 CONFIG_SPLASH_SCREEN_ALIGN
1132 If this option is set the splash image can be freely positioned
1133 on the screen. Environment variable "splashpos" specifies the
1134 position as "x,y". If a positive number is given it is used as
1135 number of pixel from left/top. If a negative number is given it
1136 is used as number of pixel from right/bottom. You can also
1137 specify 'm' for centering the image.
1140 setenv splashpos m,m
1141 => image at center of screen
1143 setenv splashpos 30,20
1144 => image at x = 30 and y = 20
1146 setenv splashpos -10,m
1147 => vertically centered image
1148 at x = dspWidth - bmpWidth - 9
1150 - Gzip compressed BMP image support: CONFIG_VIDEO_BMP_GZIP
1152 If this option is set, additionally to standard BMP
1153 images, gzipped BMP images can be displayed via the
1154 splashscreen support or the bmp command.
1156 - Run length encoded BMP image (RLE8) support: CONFIG_VIDEO_BMP_RLE8
1158 If this option is set, 8-bit RLE compressed BMP images
1159 can be displayed via the splashscreen support or the
1162 - Compression support:
1165 If this option is set, support for bzip2 compressed
1166 images is included. If not, only uncompressed and gzip
1167 compressed images are supported.
1169 NOTE: the bzip2 algorithm requires a lot of RAM, so
1170 the malloc area (as defined by CONFIG_SYS_MALLOC_LEN) should
1175 If this option is set, support for lzma compressed
1178 Note: The LZMA algorithm adds between 2 and 4KB of code and it
1179 requires an amount of dynamic memory that is given by the
1182 (1846 + 768 << (lc + lp)) * sizeof(uint16)
1184 Where lc and lp stand for, respectively, Literal context bits
1185 and Literal pos bits.
1187 This value is upper-bounded by 14MB in the worst case. Anyway,
1188 for a ~4MB large kernel image, we have lc=3 and lp=0 for a
1189 total amount of (1846 + 768 << (3 + 0)) * 2 = ~41KB... that is
1190 a very small buffer.
1192 Use the lzmainfo tool to determinate the lc and lp values and
1193 then calculate the amount of needed dynamic memory (ensuring
1194 the appropriate CONFIG_SYS_MALLOC_LEN value).
1199 The address of PHY on MII bus.
1201 CONFIG_PHY_CLOCK_FREQ (ppc4xx)
1203 The clock frequency of the MII bus
1207 If this option is set, support for speed/duplex
1208 detection of gigabit PHY is included.
1210 CONFIG_PHY_RESET_DELAY
1212 Some PHY like Intel LXT971A need extra delay after
1213 reset before any MII register access is possible.
1214 For such PHY, set this option to the usec delay
1215 required. (minimum 300usec for LXT971A)
1217 CONFIG_PHY_CMD_DELAY (ppc4xx)
1219 Some PHY like Intel LXT971A need extra delay after
1220 command issued before MII status register can be read
1230 Define a default value for Ethernet address to use
1231 for the respective Ethernet interface, in case this
1232 is not determined automatically.
1237 Define a default value for the IP address to use for
1238 the default Ethernet interface, in case this is not
1239 determined through e.g. bootp.
1241 - Server IP address:
1244 Defines a default value for the IP address of a TFTP
1245 server to contact when using the "tftboot" command.
1247 CONFIG_KEEP_SERVERADDR
1249 Keeps the server's MAC address, in the env 'serveraddr'
1250 for passing to bootargs (like Linux's netconsole option)
1252 - Multicast TFTP Mode:
1255 Defines whether you want to support multicast TFTP as per
1256 rfc-2090; for example to work with atftp. Lets lots of targets
1257 tftp down the same boot image concurrently. Note: the Ethernet
1258 driver in use must provide a function: mcast() to join/leave a
1261 CONFIG_BOOTP_RANDOM_DELAY
1262 - BOOTP Recovery Mode:
1263 CONFIG_BOOTP_RANDOM_DELAY
1265 If you have many targets in a network that try to
1266 boot using BOOTP, you may want to avoid that all
1267 systems send out BOOTP requests at precisely the same
1268 moment (which would happen for instance at recovery
1269 from a power failure, when all systems will try to
1270 boot, thus flooding the BOOTP server. Defining
1271 CONFIG_BOOTP_RANDOM_DELAY causes a random delay to be
1272 inserted before sending out BOOTP requests. The
1273 following delays are inserted then:
1275 1st BOOTP request: delay 0 ... 1 sec
1276 2nd BOOTP request: delay 0 ... 2 sec
1277 3rd BOOTP request: delay 0 ... 4 sec
1279 BOOTP requests: delay 0 ... 8 sec
1281 - DHCP Advanced Options:
1282 You can fine tune the DHCP functionality by defining
1283 CONFIG_BOOTP_* symbols:
1285 CONFIG_BOOTP_SUBNETMASK
1286 CONFIG_BOOTP_GATEWAY
1287 CONFIG_BOOTP_HOSTNAME
1288 CONFIG_BOOTP_NISDOMAIN
1289 CONFIG_BOOTP_BOOTPATH
1290 CONFIG_BOOTP_BOOTFILESIZE
1293 CONFIG_BOOTP_SEND_HOSTNAME
1294 CONFIG_BOOTP_NTPSERVER
1295 CONFIG_BOOTP_TIMEOFFSET
1296 CONFIG_BOOTP_VENDOREX
1298 CONFIG_BOOTP_SERVERIP - TFTP server will be the serverip
1299 environment variable, not the BOOTP server.
1301 CONFIG_BOOTP_DNS2 - If a DHCP client requests the DNS
1302 serverip from a DHCP server, it is possible that more
1303 than one DNS serverip is offered to the client.
1304 If CONFIG_BOOTP_DNS2 is enabled, the secondary DNS
1305 serverip will be stored in the additional environment
1306 variable "dnsip2". The first DNS serverip is always
1307 stored in the variable "dnsip", when CONFIG_BOOTP_DNS
1310 CONFIG_BOOTP_SEND_HOSTNAME - Some DHCP servers are capable
1311 to do a dynamic update of a DNS server. To do this, they
1312 need the hostname of the DHCP requester.
1313 If CONFIG_BOOTP_SEND_HOSTNAME is defined, the content
1314 of the "hostname" environment variable is passed as
1315 option 12 to the DHCP server.
1317 CONFIG_BOOTP_DHCP_REQUEST_DELAY
1319 A 32bit value in microseconds for a delay between
1320 receiving a "DHCP Offer" and sending the "DHCP Request".
1321 This fixes a problem with certain DHCP servers that don't
1322 respond 100% of the time to a "DHCP request". E.g. On an
1323 AT91RM9200 processor running at 180MHz, this delay needed
1324 to be *at least* 15,000 usec before a Windows Server 2003
1325 DHCP server would reply 100% of the time. I recommend at
1326 least 50,000 usec to be safe. The alternative is to hope
1327 that one of the retries will be successful but note that
1328 the DHCP timeout and retry process takes a longer than
1332 CONFIG_CDP_DEVICE_ID
1334 The device id used in CDP trigger frames.
1336 CONFIG_CDP_DEVICE_ID_PREFIX
1338 A two character string which is prefixed to the MAC address
1343 A printf format string which contains the ascii name of
1344 the port. Normally is set to "eth%d" which sets
1345 eth0 for the first Ethernet, eth1 for the second etc.
1347 CONFIG_CDP_CAPABILITIES
1349 A 32bit integer which indicates the device capabilities;
1350 0x00000010 for a normal host which does not forwards.
1354 An ascii string containing the version of the software.
1358 An ascii string containing the name of the platform.
1362 A 32bit integer sent on the trigger.
1364 CONFIG_CDP_POWER_CONSUMPTION
1366 A 16bit integer containing the power consumption of the
1367 device in .1 of milliwatts.
1369 CONFIG_CDP_APPLIANCE_VLAN_TYPE
1371 A byte containing the id of the VLAN.
1373 - Status LED: CONFIG_STATUS_LED
1375 Several configurations allow to display the current
1376 status using a LED. For instance, the LED will blink
1377 fast while running U-Boot code, stop blinking as
1378 soon as a reply to a BOOTP request was received, and
1379 start blinking slow once the Linux kernel is running
1380 (supported by a status LED driver in the Linux
1381 kernel). Defining CONFIG_STATUS_LED enables this
1384 - CAN Support: CONFIG_CAN_DRIVER
1386 Defining CONFIG_CAN_DRIVER enables CAN driver support
1387 on those systems that support this (optional)
1388 feature, like the TQM8xxL modules.
1390 - I2C Support: CONFIG_HARD_I2C | CONFIG_SOFT_I2C
1392 These enable I2C serial bus commands. Defining either of
1393 (but not both of) CONFIG_HARD_I2C or CONFIG_SOFT_I2C will
1394 include the appropriate I2C driver for the selected CPU.
1396 This will allow you to use i2c commands at the u-boot
1397 command line (as long as you set CONFIG_CMD_I2C in
1398 CONFIG_COMMANDS) and communicate with i2c based realtime
1399 clock chips. See common/cmd_i2c.c for a description of the
1400 command line interface.
1402 CONFIG_HARD_I2C selects a hardware I2C controller.
1404 CONFIG_SOFT_I2C configures u-boot to use a software (aka
1405 bit-banging) driver instead of CPM or similar hardware
1408 There are several other quantities that must also be
1409 defined when you define CONFIG_HARD_I2C or CONFIG_SOFT_I2C.
1411 In both cases you will need to define CONFIG_SYS_I2C_SPEED
1412 to be the frequency (in Hz) at which you wish your i2c bus
1413 to run and CONFIG_SYS_I2C_SLAVE to be the address of this node (ie
1414 the CPU's i2c node address).
1416 Now, the u-boot i2c code for the mpc8xx
1417 (arch/powerpc/cpu/mpc8xx/i2c.c) sets the CPU up as a master node
1418 and so its address should therefore be cleared to 0 (See,
1419 eg, MPC823e User's Manual p.16-473). So, set
1420 CONFIG_SYS_I2C_SLAVE to 0.
1422 CONFIG_SYS_I2C_INIT_MPC5XXX
1424 When a board is reset during an i2c bus transfer
1425 chips might think that the current transfer is still
1426 in progress. Reset the slave devices by sending start
1427 commands until the slave device responds.
1429 That's all that's required for CONFIG_HARD_I2C.
1431 If you use the software i2c interface (CONFIG_SOFT_I2C)
1432 then the following macros need to be defined (examples are
1433 from include/configs/lwmon.h):
1437 (Optional). Any commands necessary to enable the I2C
1438 controller or configure ports.
1440 eg: #define I2C_INIT (immr->im_cpm.cp_pbdir |= PB_SCL)
1444 (Only for MPC8260 CPU). The I/O port to use (the code
1445 assumes both bits are on the same port). Valid values
1446 are 0..3 for ports A..D.
1450 The code necessary to make the I2C data line active
1451 (driven). If the data line is open collector, this
1454 eg: #define I2C_ACTIVE (immr->im_cpm.cp_pbdir |= PB_SDA)
1458 The code necessary to make the I2C data line tri-stated
1459 (inactive). If the data line is open collector, this
1462 eg: #define I2C_TRISTATE (immr->im_cpm.cp_pbdir &= ~PB_SDA)
1466 Code that returns TRUE if the I2C data line is high,
1469 eg: #define I2C_READ ((immr->im_cpm.cp_pbdat & PB_SDA) != 0)
1473 If <bit> is TRUE, sets the I2C data line high. If it
1474 is FALSE, it clears it (low).
1476 eg: #define I2C_SDA(bit) \
1477 if(bit) immr->im_cpm.cp_pbdat |= PB_SDA; \
1478 else immr->im_cpm.cp_pbdat &= ~PB_SDA
1482 If <bit> is TRUE, sets the I2C clock line high. If it
1483 is FALSE, it clears it (low).
1485 eg: #define I2C_SCL(bit) \
1486 if(bit) immr->im_cpm.cp_pbdat |= PB_SCL; \
1487 else immr->im_cpm.cp_pbdat &= ~PB_SCL
1491 This delay is invoked four times per clock cycle so this
1492 controls the rate of data transfer. The data rate thus
1493 is 1 / (I2C_DELAY * 4). Often defined to be something
1496 #define I2C_DELAY udelay(2)
1498 CONFIG_SOFT_I2C_GPIO_SCL / CONFIG_SOFT_I2C_GPIO_SDA
1500 If your arch supports the generic GPIO framework (asm/gpio.h),
1501 then you may alternatively define the two GPIOs that are to be
1502 used as SCL / SDA. Any of the previous I2C_xxx macros will
1503 have GPIO-based defaults assigned to them as appropriate.
1505 You should define these to the GPIO value as given directly to
1506 the generic GPIO functions.
1508 CONFIG_SYS_I2C_INIT_BOARD
1510 When a board is reset during an i2c bus transfer
1511 chips might think that the current transfer is still
1512 in progress. On some boards it is possible to access
1513 the i2c SCLK line directly, either by using the
1514 processor pin as a GPIO or by having a second pin
1515 connected to the bus. If this option is defined a
1516 custom i2c_init_board() routine in boards/xxx/board.c
1517 is run early in the boot sequence.
1519 CONFIG_SYS_I2C_BOARD_LATE_INIT
1521 An alternative to CONFIG_SYS_I2C_INIT_BOARD. If this option is
1522 defined a custom i2c_board_late_init() routine in
1523 boards/xxx/board.c is run AFTER the operations in i2c_init()
1524 is completed. This callpoint can be used to unreset i2c bus
1525 using CPU i2c controller register accesses for CPUs whose i2c
1526 controller provide such a method. It is called at the end of
1527 i2c_init() to allow i2c_init operations to setup the i2c bus
1528 controller on the CPU (e.g. setting bus speed & slave address).
1530 CONFIG_I2CFAST (PPC405GP|PPC405EP only)
1532 This option enables configuration of bi_iic_fast[] flags
1533 in u-boot bd_info structure based on u-boot environment
1534 variable "i2cfast". (see also i2cfast)
1536 CONFIG_I2C_MULTI_BUS
1538 This option allows the use of multiple I2C buses, each of which
1539 must have a controller. At any point in time, only one bus is
1540 active. To switch to a different bus, use the 'i2c dev' command.
1541 Note that bus numbering is zero-based.
1543 CONFIG_SYS_I2C_NOPROBES
1545 This option specifies a list of I2C devices that will be skipped
1546 when the 'i2c probe' command is issued. If CONFIG_I2C_MULTI_BUS
1547 is set, specify a list of bus-device pairs. Otherwise, specify
1548 a 1D array of device addresses
1551 #undef CONFIG_I2C_MULTI_BUS
1552 #define CONFIG_SYS_I2C_NOPROBES {0x50,0x68}
1554 will skip addresses 0x50 and 0x68 on a board with one I2C bus
1556 #define CONFIG_I2C_MULTI_BUS
1557 #define CONFIG_SYS_I2C_MULTI_NOPROBES {{0,0x50},{0,0x68},{1,0x54}}
1559 will skip addresses 0x50 and 0x68 on bus 0 and address 0x54 on bus 1
1561 CONFIG_SYS_SPD_BUS_NUM
1563 If defined, then this indicates the I2C bus number for DDR SPD.
1564 If not defined, then U-Boot assumes that SPD is on I2C bus 0.
1566 CONFIG_SYS_RTC_BUS_NUM
1568 If defined, then this indicates the I2C bus number for the RTC.
1569 If not defined, then U-Boot assumes that RTC is on I2C bus 0.
1571 CONFIG_SYS_DTT_BUS_NUM
1573 If defined, then this indicates the I2C bus number for the DTT.
1574 If not defined, then U-Boot assumes that DTT is on I2C bus 0.
1576 CONFIG_SYS_I2C_DTT_ADDR:
1578 If defined, specifies the I2C address of the DTT device.
1579 If not defined, then U-Boot uses predefined value for
1580 specified DTT device.
1584 Define this option if you want to use Freescale's I2C driver in
1585 drivers/i2c/fsl_i2c.c.
1589 Define this option if you have I2C devices reached over 1 .. n
1590 I2C Muxes like the pca9544a. This option addes a new I2C
1591 Command "i2c bus [muxtype:muxaddr:muxchannel]" which adds a
1592 new I2C Bus to the existing I2C Busses. If you select the
1593 new Bus with "i2c dev", u-bbot sends first the commandos for
1594 the muxes to activate this new "bus".
1596 CONFIG_I2C_MULTI_BUS must be also defined, to use this
1600 Adding a new I2C Bus reached over 2 pca9544a muxes
1601 The First mux with address 70 and channel 6
1602 The Second mux with address 71 and channel 4
1604 => i2c bus pca9544a:70:6:pca9544a:71:4
1606 Use the "i2c bus" command without parameter, to get a list
1607 of I2C Busses with muxes:
1610 Busses reached over muxes:
1612 reached over Mux(es):
1615 reached over Mux(es):
1620 If you now switch to the new I2C Bus 3 with "i2c dev 3"
1621 u-boot sends First the Commando to the mux@70 to enable
1622 channel 6, and then the Commando to the mux@71 to enable
1625 After that, you can use the "normal" i2c commands as
1626 usual, to communicate with your I2C devices behind
1629 This option is actually implemented for the bitbanging
1630 algorithm in common/soft_i2c.c and for the Hardware I2C
1631 Bus on the MPC8260. But it should be not so difficult
1632 to add this option to other architectures.
1634 CONFIG_SOFT_I2C_READ_REPEATED_START
1636 defining this will force the i2c_read() function in
1637 the soft_i2c driver to perform an I2C repeated start
1638 between writing the address pointer and reading the
1639 data. If this define is omitted the default behaviour
1640 of doing a stop-start sequence will be used. Most I2C
1641 devices can use either method, but some require one or
1644 - SPI Support: CONFIG_SPI
1646 Enables SPI driver (so far only tested with
1647 SPI EEPROM, also an instance works with Crystal A/D and
1648 D/As on the SACSng board)
1652 Enables extended (16-bit) SPI EEPROM addressing.
1653 (symmetrical to CONFIG_I2C_X)
1657 Enables a software (bit-bang) SPI driver rather than
1658 using hardware support. This is a general purpose
1659 driver that only requires three general I/O port pins
1660 (two outputs, one input) to function. If this is
1661 defined, the board configuration must define several
1662 SPI configuration items (port pins to use, etc). For
1663 an example, see include/configs/sacsng.h.
1667 Enables a hardware SPI driver for general-purpose reads
1668 and writes. As with CONFIG_SOFT_SPI, the board configuration
1669 must define a list of chip-select function pointers.
1670 Currently supported on some MPC8xxx processors. For an
1671 example, see include/configs/mpc8349emds.h.
1675 Enables the driver for the SPI controllers on i.MX and MXC
1676 SoCs. Currently only i.MX31 is supported.
1678 - FPGA Support: CONFIG_FPGA
1680 Enables FPGA subsystem.
1682 CONFIG_FPGA_<vendor>
1684 Enables support for specific chip vendors.
1687 CONFIG_FPGA_<family>
1689 Enables support for FPGA family.
1690 (SPARTAN2, SPARTAN3, VIRTEX2, CYCLONE2, ACEX1K, ACEX)
1694 Specify the number of FPGA devices to support.
1696 CONFIG_SYS_FPGA_PROG_FEEDBACK
1698 Enable printing of hash marks during FPGA configuration.
1700 CONFIG_SYS_FPGA_CHECK_BUSY
1702 Enable checks on FPGA configuration interface busy
1703 status by the configuration function. This option
1704 will require a board or device specific function to
1709 If defined, a function that provides delays in the FPGA
1710 configuration driver.
1712 CONFIG_SYS_FPGA_CHECK_CTRLC
1713 Allow Control-C to interrupt FPGA configuration
1715 CONFIG_SYS_FPGA_CHECK_ERROR
1717 Check for configuration errors during FPGA bitfile
1718 loading. For example, abort during Virtex II
1719 configuration if the INIT_B line goes low (which
1720 indicated a CRC error).
1722 CONFIG_SYS_FPGA_WAIT_INIT
1724 Maximum time to wait for the INIT_B line to deassert
1725 after PROB_B has been deasserted during a Virtex II
1726 FPGA configuration sequence. The default time is 500
1729 CONFIG_SYS_FPGA_WAIT_BUSY
1731 Maximum time to wait for BUSY to deassert during
1732 Virtex II FPGA configuration. The default is 5 ms.
1734 CONFIG_SYS_FPGA_WAIT_CONFIG
1736 Time to wait after FPGA configuration. The default is
1739 - Configuration Management:
1742 If defined, this string will be added to the U-Boot
1743 version information (U_BOOT_VERSION)
1745 - Vendor Parameter Protection:
1747 U-Boot considers the values of the environment
1748 variables "serial#" (Board Serial Number) and
1749 "ethaddr" (Ethernet Address) to be parameters that
1750 are set once by the board vendor / manufacturer, and
1751 protects these variables from casual modification by
1752 the user. Once set, these variables are read-only,
1753 and write or delete attempts are rejected. You can
1754 change this behaviour:
1756 If CONFIG_ENV_OVERWRITE is #defined in your config
1757 file, the write protection for vendor parameters is
1758 completely disabled. Anybody can change or delete
1761 Alternatively, if you #define _both_ CONFIG_ETHADDR
1762 _and_ CONFIG_OVERWRITE_ETHADDR_ONCE, a default
1763 Ethernet address is installed in the environment,
1764 which can be changed exactly ONCE by the user. [The
1765 serial# is unaffected by this, i. e. it remains
1771 Define this variable to enable the reservation of
1772 "protected RAM", i. e. RAM which is not overwritten
1773 by U-Boot. Define CONFIG_PRAM to hold the number of
1774 kB you want to reserve for pRAM. You can overwrite
1775 this default value by defining an environment
1776 variable "pram" to the number of kB you want to
1777 reserve. Note that the board info structure will
1778 still show the full amount of RAM. If pRAM is
1779 reserved, a new environment variable "mem" will
1780 automatically be defined to hold the amount of
1781 remaining RAM in a form that can be passed as boot
1782 argument to Linux, for instance like that:
1784 setenv bootargs ... mem=\${mem}
1787 This way you can tell Linux not to use this memory,
1788 either, which results in a memory region that will
1789 not be affected by reboots.
1791 *WARNING* If your board configuration uses automatic
1792 detection of the RAM size, you must make sure that
1793 this memory test is non-destructive. So far, the
1794 following board configurations are known to be
1797 ETX094, IVMS8, IVML24, SPD8xx, TQM8xxL,
1798 HERMES, IP860, RPXlite, LWMON, LANTEC,
1799 PCU_E, FLAGADM, TQM8260
1804 Define this variable to stop the system in case of a
1805 fatal error, so that you have to reset it manually.
1806 This is probably NOT a good idea for an embedded
1807 system where you want the system to reboot
1808 automatically as fast as possible, but it may be
1809 useful during development since you can try to debug
1810 the conditions that lead to the situation.
1812 CONFIG_NET_RETRY_COUNT
1814 This variable defines the number of retries for
1815 network operations like ARP, RARP, TFTP, or BOOTP
1816 before giving up the operation. If not defined, a
1817 default value of 5 is used.
1821 Timeout waiting for an ARP reply in milliseconds.
1823 - Command Interpreter:
1824 CONFIG_AUTO_COMPLETE
1826 Enable auto completion of commands using TAB.
1828 Note that this feature has NOT been implemented yet
1829 for the "hush" shell.
1832 CONFIG_SYS_HUSH_PARSER
1834 Define this variable to enable the "hush" shell (from
1835 Busybox) as command line interpreter, thus enabling
1836 powerful command line syntax like
1837 if...then...else...fi conditionals or `&&' and '||'
1838 constructs ("shell scripts").
1840 If undefined, you get the old, much simpler behaviour
1841 with a somewhat smaller memory footprint.
1844 CONFIG_SYS_PROMPT_HUSH_PS2
1846 This defines the secondary prompt string, which is
1847 printed when the command interpreter needs more input
1848 to complete a command. Usually "> ".
1852 In the current implementation, the local variables
1853 space and global environment variables space are
1854 separated. Local variables are those you define by
1855 simply typing `name=value'. To access a local
1856 variable later on, you have write `$name' or
1857 `${name}'; to execute the contents of a variable
1858 directly type `$name' at the command prompt.
1860 Global environment variables are those you use
1861 setenv/printenv to work with. To run a command stored
1862 in such a variable, you need to use the run command,
1863 and you must not use the '$' sign to access them.
1865 To store commands and special characters in a
1866 variable, please use double quotation marks
1867 surrounding the whole text of the variable, instead
1868 of the backslashes before semicolons and special
1871 - Commandline Editing and History:
1872 CONFIG_CMDLINE_EDITING
1874 Enable editing and History functions for interactive
1875 commandline input operations
1877 - Default Environment:
1878 CONFIG_EXTRA_ENV_SETTINGS
1880 Define this to contain any number of null terminated
1881 strings (variable = value pairs) that will be part of
1882 the default environment compiled into the boot image.
1884 For example, place something like this in your
1885 board's config file:
1887 #define CONFIG_EXTRA_ENV_SETTINGS \
1891 Warning: This method is based on knowledge about the
1892 internal format how the environment is stored by the
1893 U-Boot code. This is NOT an official, exported
1894 interface! Although it is unlikely that this format
1895 will change soon, there is no guarantee either.
1896 You better know what you are doing here.
1898 Note: overly (ab)use of the default environment is
1899 discouraged. Make sure to check other ways to preset
1900 the environment like the "source" command or the
1903 - DataFlash Support:
1904 CONFIG_HAS_DATAFLASH
1906 Defining this option enables DataFlash features and
1907 allows to read/write in Dataflash via the standard
1910 - SystemACE Support:
1913 Adding this option adds support for Xilinx SystemACE
1914 chips attached via some sort of local bus. The address
1915 of the chip must also be defined in the
1916 CONFIG_SYS_SYSTEMACE_BASE macro. For example:
1918 #define CONFIG_SYSTEMACE
1919 #define CONFIG_SYS_SYSTEMACE_BASE 0xf0000000
1921 When SystemACE support is added, the "ace" device type
1922 becomes available to the fat commands, i.e. fatls.
1924 - TFTP Fixed UDP Port:
1927 If this is defined, the environment variable tftpsrcp
1928 is used to supply the TFTP UDP source port value.
1929 If tftpsrcp isn't defined, the normal pseudo-random port
1930 number generator is used.
1932 Also, the environment variable tftpdstp is used to supply
1933 the TFTP UDP destination port value. If tftpdstp isn't
1934 defined, the normal port 69 is used.
1936 The purpose for tftpsrcp is to allow a TFTP server to
1937 blindly start the TFTP transfer using the pre-configured
1938 target IP address and UDP port. This has the effect of
1939 "punching through" the (Windows XP) firewall, allowing
1940 the remainder of the TFTP transfer to proceed normally.
1941 A better solution is to properly configure the firewall,
1942 but sometimes that is not allowed.
1944 - Show boot progress:
1945 CONFIG_SHOW_BOOT_PROGRESS
1947 Defining this option allows to add some board-
1948 specific code (calling a user-provided function
1949 "show_boot_progress(int)") that enables you to show
1950 the system's boot progress on some display (for
1951 example, some LED's) on your board. At the moment,
1952 the following checkpoints are implemented:
1954 Legacy uImage format:
1957 1 common/cmd_bootm.c before attempting to boot an image
1958 -1 common/cmd_bootm.c Image header has bad magic number
1959 2 common/cmd_bootm.c Image header has correct magic number
1960 -2 common/cmd_bootm.c Image header has bad checksum
1961 3 common/cmd_bootm.c Image header has correct checksum
1962 -3 common/cmd_bootm.c Image data has bad checksum
1963 4 common/cmd_bootm.c Image data has correct checksum
1964 -4 common/cmd_bootm.c Image is for unsupported architecture
1965 5 common/cmd_bootm.c Architecture check OK
1966 -5 common/cmd_bootm.c Wrong Image Type (not kernel, multi)
1967 6 common/cmd_bootm.c Image Type check OK
1968 -6 common/cmd_bootm.c gunzip uncompression error
1969 -7 common/cmd_bootm.c Unimplemented compression type
1970 7 common/cmd_bootm.c Uncompression OK
1971 8 common/cmd_bootm.c No uncompress/copy overwrite error
1972 -9 common/cmd_bootm.c Unsupported OS (not Linux, BSD, VxWorks, QNX)
1974 9 common/image.c Start initial ramdisk verification
1975 -10 common/image.c Ramdisk header has bad magic number
1976 -11 common/image.c Ramdisk header has bad checksum
1977 10 common/image.c Ramdisk header is OK
1978 -12 common/image.c Ramdisk data has bad checksum
1979 11 common/image.c Ramdisk data has correct checksum
1980 12 common/image.c Ramdisk verification complete, start loading
1981 -13 common/image.c Wrong Image Type (not PPC Linux ramdisk)
1982 13 common/image.c Start multifile image verification
1983 14 common/image.c No initial ramdisk, no multifile, continue.
1985 15 arch/<arch>/lib/bootm.c All preparation done, transferring control to OS
1987 -30 arch/powerpc/lib/board.c Fatal error, hang the system
1988 -31 post/post.c POST test failed, detected by post_output_backlog()
1989 -32 post/post.c POST test failed, detected by post_run_single()
1991 34 common/cmd_doc.c before loading a Image from a DOC device
1992 -35 common/cmd_doc.c Bad usage of "doc" command
1993 35 common/cmd_doc.c correct usage of "doc" command
1994 -36 common/cmd_doc.c No boot device
1995 36 common/cmd_doc.c correct boot device
1996 -37 common/cmd_doc.c Unknown Chip ID on boot device
1997 37 common/cmd_doc.c correct chip ID found, device available
1998 -38 common/cmd_doc.c Read Error on boot device
1999 38 common/cmd_doc.c reading Image header from DOC device OK
2000 -39 common/cmd_doc.c Image header has bad magic number
2001 39 common/cmd_doc.c Image header has correct magic number
2002 -40 common/cmd_doc.c Error reading Image from DOC device
2003 40 common/cmd_doc.c Image header has correct magic number
2004 41 common/cmd_ide.c before loading a Image from a IDE device
2005 -42 common/cmd_ide.c Bad usage of "ide" command
2006 42 common/cmd_ide.c correct usage of "ide" command
2007 -43 common/cmd_ide.c No boot device
2008 43 common/cmd_ide.c boot device found
2009 -44 common/cmd_ide.c Device not available
2010 44 common/cmd_ide.c Device available
2011 -45 common/cmd_ide.c wrong partition selected
2012 45 common/cmd_ide.c partition selected
2013 -46 common/cmd_ide.c Unknown partition table
2014 46 common/cmd_ide.c valid partition table found
2015 -47 common/cmd_ide.c Invalid partition type
2016 47 common/cmd_ide.c correct partition type
2017 -48 common/cmd_ide.c Error reading Image Header on boot device
2018 48 common/cmd_ide.c reading Image Header from IDE device OK
2019 -49 common/cmd_ide.c Image header has bad magic number
2020 49 common/cmd_ide.c Image header has correct magic number
2021 -50 common/cmd_ide.c Image header has bad checksum
2022 50 common/cmd_ide.c Image header has correct checksum
2023 -51 common/cmd_ide.c Error reading Image from IDE device
2024 51 common/cmd_ide.c reading Image from IDE device OK
2025 52 common/cmd_nand.c before loading a Image from a NAND device
2026 -53 common/cmd_nand.c Bad usage of "nand" command
2027 53 common/cmd_nand.c correct usage of "nand" command
2028 -54 common/cmd_nand.c No boot device
2029 54 common/cmd_nand.c boot device found
2030 -55 common/cmd_nand.c Unknown Chip ID on boot device
2031 55 common/cmd_nand.c correct chip ID found, device available
2032 -56 common/cmd_nand.c Error reading Image Header on boot device
2033 56 common/cmd_nand.c reading Image Header from NAND device OK
2034 -57 common/cmd_nand.c Image header has bad magic number
2035 57 common/cmd_nand.c Image header has correct magic number
2036 -58 common/cmd_nand.c Error reading Image from NAND device
2037 58 common/cmd_nand.c reading Image from NAND device OK
2039 -60 common/env_common.c Environment has a bad CRC, using default
2041 64 net/eth.c starting with Ethernet configuration.
2042 -64 net/eth.c no Ethernet found.
2043 65 net/eth.c Ethernet found.
2045 -80 common/cmd_net.c usage wrong
2046 80 common/cmd_net.c before calling NetLoop()
2047 -81 common/cmd_net.c some error in NetLoop() occurred
2048 81 common/cmd_net.c NetLoop() back without error
2049 -82 common/cmd_net.c size == 0 (File with size 0 loaded)
2050 82 common/cmd_net.c trying automatic boot
2051 83 common/cmd_net.c running "source" command
2052 -83 common/cmd_net.c some error in automatic boot or "source" command
2053 84 common/cmd_net.c end without errors
2058 100 common/cmd_bootm.c Kernel FIT Image has correct format
2059 -100 common/cmd_bootm.c Kernel FIT Image has incorrect format
2060 101 common/cmd_bootm.c No Kernel subimage unit name, using configuration
2061 -101 common/cmd_bootm.c Can't get configuration for kernel subimage
2062 102 common/cmd_bootm.c Kernel unit name specified
2063 -103 common/cmd_bootm.c Can't get kernel subimage node offset
2064 103 common/cmd_bootm.c Found configuration node
2065 104 common/cmd_bootm.c Got kernel subimage node offset
2066 -104 common/cmd_bootm.c Kernel subimage hash verification failed
2067 105 common/cmd_bootm.c Kernel subimage hash verification OK
2068 -105 common/cmd_bootm.c Kernel subimage is for unsupported architecture
2069 106 common/cmd_bootm.c Architecture check OK
2070 -106 common/cmd_bootm.c Kernel subimage has wrong type
2071 107 common/cmd_bootm.c Kernel subimage type OK
2072 -107 common/cmd_bootm.c Can't get kernel subimage data/size
2073 108 common/cmd_bootm.c Got kernel subimage data/size
2074 -108 common/cmd_bootm.c Wrong image type (not legacy, FIT)
2075 -109 common/cmd_bootm.c Can't get kernel subimage type
2076 -110 common/cmd_bootm.c Can't get kernel subimage comp
2077 -111 common/cmd_bootm.c Can't get kernel subimage os
2078 -112 common/cmd_bootm.c Can't get kernel subimage load address
2079 -113 common/cmd_bootm.c Image uncompress/copy overwrite error
2081 120 common/image.c Start initial ramdisk verification
2082 -120 common/image.c Ramdisk FIT image has incorrect format
2083 121 common/image.c Ramdisk FIT image has correct format
2084 122 common/image.c No ramdisk subimage unit name, using configuration
2085 -122 common/image.c Can't get configuration for ramdisk subimage
2086 123 common/image.c Ramdisk unit name specified
2087 -124 common/image.c Can't get ramdisk subimage node offset
2088 125 common/image.c Got ramdisk subimage node offset
2089 -125 common/image.c Ramdisk subimage hash verification failed
2090 126 common/image.c Ramdisk subimage hash verification OK
2091 -126 common/image.c Ramdisk subimage for unsupported architecture
2092 127 common/image.c Architecture check OK
2093 -127 common/image.c Can't get ramdisk subimage data/size
2094 128 common/image.c Got ramdisk subimage data/size
2095 129 common/image.c Can't get ramdisk load address
2096 -129 common/image.c Got ramdisk load address
2098 -130 common/cmd_doc.c Incorrect FIT image format
2099 131 common/cmd_doc.c FIT image format OK
2101 -140 common/cmd_ide.c Incorrect FIT image format
2102 141 common/cmd_ide.c FIT image format OK
2104 -150 common/cmd_nand.c Incorrect FIT image format
2105 151 common/cmd_nand.c FIT image format OK
2107 - Automatic software updates via TFTP server
2109 CONFIG_UPDATE_TFTP_CNT_MAX
2110 CONFIG_UPDATE_TFTP_MSEC_MAX
2112 These options enable and control the auto-update feature;
2113 for a more detailed description refer to doc/README.update.
2115 - MTD Support (mtdparts command, UBI support)
2118 Adds the MTD device infrastructure from the Linux kernel.
2119 Needed for mtdparts command support.
2121 CONFIG_MTD_PARTITIONS
2123 Adds the MTD partitioning infrastructure from the Linux
2124 kernel. Needed for UBI support.
2130 [so far only for SMDK2400 and TRAB boards]
2132 - Modem support enable:
2133 CONFIG_MODEM_SUPPORT
2135 - RTS/CTS Flow control enable:
2138 - Modem debug support:
2139 CONFIG_MODEM_SUPPORT_DEBUG
2141 Enables debugging stuff (char screen[1024], dbg())
2142 for modem support. Useful only with BDI2000.
2144 - Interrupt support (PPC):
2146 There are common interrupt_init() and timer_interrupt()
2147 for all PPC archs. interrupt_init() calls interrupt_init_cpu()
2148 for CPU specific initialization. interrupt_init_cpu()
2149 should set decrementer_count to appropriate value. If
2150 CPU resets decrementer automatically after interrupt
2151 (ppc4xx) it should set decrementer_count to zero.
2152 timer_interrupt() calls timer_interrupt_cpu() for CPU
2153 specific handling. If board has watchdog / status_led
2154 / other_activity_monitor it works automatically from
2155 general timer_interrupt().
2159 In the target system modem support is enabled when a
2160 specific key (key combination) is pressed during
2161 power-on. Otherwise U-Boot will boot normally
2162 (autoboot). The key_pressed() function is called from
2163 board_init(). Currently key_pressed() is a dummy
2164 function, returning 1 and thus enabling modem
2167 If there are no modem init strings in the
2168 environment, U-Boot proceed to autoboot; the
2169 previous output (banner, info printfs) will be
2172 See also: doc/README.Modem
2175 Configuration Settings:
2176 -----------------------
2178 - CONFIG_SYS_LONGHELP: Defined when you want long help messages included;
2179 undefine this when you're short of memory.
2181 - CONFIG_SYS_HELP_CMD_WIDTH: Defined when you want to override the default
2182 width of the commands listed in the 'help' command output.
2184 - CONFIG_SYS_PROMPT: This is what U-Boot prints on the console to
2185 prompt for user input.
2187 - CONFIG_SYS_CBSIZE: Buffer size for input from the Console
2189 - CONFIG_SYS_PBSIZE: Buffer size for Console output
2191 - CONFIG_SYS_MAXARGS: max. Number of arguments accepted for monitor commands
2193 - CONFIG_SYS_BARGSIZE: Buffer size for Boot Arguments which are passed to
2194 the application (usually a Linux kernel) when it is
2197 - CONFIG_SYS_BAUDRATE_TABLE:
2198 List of legal baudrate settings for this board.
2200 - CONFIG_SYS_CONSOLE_INFO_QUIET
2201 Suppress display of console information at boot.
2203 - CONFIG_SYS_CONSOLE_IS_IN_ENV
2204 If the board specific function
2205 extern int overwrite_console (void);
2206 returns 1, the stdin, stderr and stdout are switched to the
2207 serial port, else the settings in the environment are used.
2209 - CONFIG_SYS_CONSOLE_OVERWRITE_ROUTINE
2210 Enable the call to overwrite_console().
2212 - CONFIG_SYS_CONSOLE_ENV_OVERWRITE
2213 Enable overwrite of previous console environment settings.
2215 - CONFIG_SYS_MEMTEST_START, CONFIG_SYS_MEMTEST_END:
2216 Begin and End addresses of the area used by the
2219 - CONFIG_SYS_ALT_MEMTEST:
2220 Enable an alternate, more extensive memory test.
2222 - CONFIG_SYS_MEMTEST_SCRATCH:
2223 Scratch address used by the alternate memory test
2224 You only need to set this if address zero isn't writeable
2226 - CONFIG_SYS_MEM_TOP_HIDE (PPC only):
2227 If CONFIG_SYS_MEM_TOP_HIDE is defined in the board config header,
2228 this specified memory area will get subtracted from the top
2229 (end) of RAM and won't get "touched" at all by U-Boot. By
2230 fixing up gd->ram_size the Linux kernel should gets passed
2231 the now "corrected" memory size and won't touch it either.
2232 This should work for arch/ppc and arch/powerpc. Only Linux
2233 board ports in arch/powerpc with bootwrapper support that
2234 recalculate the memory size from the SDRAM controller setup
2235 will have to get fixed in Linux additionally.
2237 This option can be used as a workaround for the 440EPx/GRx
2238 CHIP 11 errata where the last 256 bytes in SDRAM shouldn't
2241 WARNING: Please make sure that this value is a multiple of
2242 the Linux page size (normally 4k). If this is not the case,
2243 then the end address of the Linux memory will be located at a
2244 non page size aligned address and this could cause major
2247 - CONFIG_SYS_TFTP_LOADADDR:
2248 Default load address for network file downloads
2250 - CONFIG_SYS_LOADS_BAUD_CHANGE:
2251 Enable temporary baudrate change while serial download
2253 - CONFIG_SYS_SDRAM_BASE:
2254 Physical start address of SDRAM. _Must_ be 0 here.
2256 - CONFIG_SYS_MBIO_BASE:
2257 Physical start address of Motherboard I/O (if using a
2260 - CONFIG_SYS_FLASH_BASE:
2261 Physical start address of Flash memory.
2263 - CONFIG_SYS_MONITOR_BASE:
2264 Physical start address of boot monitor code (set by
2265 make config files to be same as the text base address
2266 (TEXT_BASE) used when linking) - same as
2267 CONFIG_SYS_FLASH_BASE when booting from flash.
2269 - CONFIG_SYS_MONITOR_LEN:
2270 Size of memory reserved for monitor code, used to
2271 determine _at_compile_time_ (!) if the environment is
2272 embedded within the U-Boot image, or in a separate
2275 - CONFIG_SYS_MALLOC_LEN:
2276 Size of DRAM reserved for malloc() use.
2278 - CONFIG_SYS_BOOTM_LEN:
2279 Normally compressed uImages are limited to an
2280 uncompressed size of 8 MBytes. If this is not enough,
2281 you can define CONFIG_SYS_BOOTM_LEN in your board config file
2282 to adjust this setting to your needs.
2284 - CONFIG_SYS_BOOTMAPSZ:
2285 Maximum size of memory mapped by the startup code of
2286 the Linux kernel; all data that must be processed by
2287 the Linux kernel (bd_info, boot arguments, FDT blob if
2288 used) must be put below this limit, unless "bootm_low"
2289 enviroment variable is defined and non-zero. In such case
2290 all data for the Linux kernel must be between "bootm_low"
2291 and "bootm_low" + CONFIG_SYS_BOOTMAPSZ.
2293 - CONFIG_SYS_MAX_FLASH_BANKS:
2294 Max number of Flash memory banks
2296 - CONFIG_SYS_MAX_FLASH_SECT:
2297 Max number of sectors on a Flash chip
2299 - CONFIG_SYS_FLASH_ERASE_TOUT:
2300 Timeout for Flash erase operations (in ms)
2302 - CONFIG_SYS_FLASH_WRITE_TOUT:
2303 Timeout for Flash write operations (in ms)
2305 - CONFIG_SYS_FLASH_LOCK_TOUT
2306 Timeout for Flash set sector lock bit operation (in ms)
2308 - CONFIG_SYS_FLASH_UNLOCK_TOUT
2309 Timeout for Flash clear lock bits operation (in ms)
2311 - CONFIG_SYS_FLASH_PROTECTION
2312 If defined, hardware flash sectors protection is used
2313 instead of U-Boot software protection.
2315 - CONFIG_SYS_DIRECT_FLASH_TFTP:
2317 Enable TFTP transfers directly to flash memory;
2318 without this option such a download has to be
2319 performed in two steps: (1) download to RAM, and (2)
2320 copy from RAM to flash.
2322 The two-step approach is usually more reliable, since
2323 you can check if the download worked before you erase
2324 the flash, but in some situations (when system RAM is
2325 too limited to allow for a temporary copy of the
2326 downloaded image) this option may be very useful.
2328 - CONFIG_SYS_FLASH_CFI:
2329 Define if the flash driver uses extra elements in the
2330 common flash structure for storing flash geometry.
2332 - CONFIG_FLASH_CFI_DRIVER
2333 This option also enables the building of the cfi_flash driver
2334 in the drivers directory
2336 - CONFIG_FLASH_CFI_MTD
2337 This option enables the building of the cfi_mtd driver
2338 in the drivers directory. The driver exports CFI flash
2341 - CONFIG_SYS_FLASH_USE_BUFFER_WRITE
2342 Use buffered writes to flash.
2344 - CONFIG_FLASH_SPANSION_S29WS_N
2345 s29ws-n MirrorBit flash has non-standard addresses for buffered
2348 - CONFIG_SYS_FLASH_QUIET_TEST
2349 If this option is defined, the common CFI flash doesn't
2350 print it's warning upon not recognized FLASH banks. This
2351 is useful, if some of the configured banks are only
2352 optionally available.
2354 - CONFIG_FLASH_SHOW_PROGRESS
2355 If defined (must be an integer), print out countdown
2356 digits and dots. Recommended value: 45 (9..1) for 80
2357 column displays, 15 (3..1) for 40 column displays.
2359 - CONFIG_SYS_RX_ETH_BUFFER:
2360 Defines the number of Ethernet receive buffers. On some
2361 Ethernet controllers it is recommended to set this value
2362 to 8 or even higher (EEPRO100 or 405 EMAC), since all
2363 buffers can be full shortly after enabling the interface
2364 on high Ethernet traffic.
2365 Defaults to 4 if not defined.
2367 - CONFIG_ENV_MAX_ENTRIES
2369 Maximum number of entries in the hash table that is used
2370 internally to store the environment settings. The default
2371 setting is supposed to be generous and should work in most
2372 cases. This setting can be used to tune behaviour; see
2373 lib/hashtable.c for details.
2375 The following definitions that deal with the placement and management
2376 of environment data (variable area); in general, we support the
2377 following configurations:
2379 - CONFIG_ENV_IS_IN_FLASH:
2381 Define this if the environment is in flash memory.
2383 a) The environment occupies one whole flash sector, which is
2384 "embedded" in the text segment with the U-Boot code. This
2385 happens usually with "bottom boot sector" or "top boot
2386 sector" type flash chips, which have several smaller
2387 sectors at the start or the end. For instance, such a
2388 layout can have sector sizes of 8, 2x4, 16, Nx32 kB. In
2389 such a case you would place the environment in one of the
2390 4 kB sectors - with U-Boot code before and after it. With
2391 "top boot sector" type flash chips, you would put the
2392 environment in one of the last sectors, leaving a gap
2393 between U-Boot and the environment.
2395 - CONFIG_ENV_OFFSET:
2397 Offset of environment data (variable area) to the
2398 beginning of flash memory; for instance, with bottom boot
2399 type flash chips the second sector can be used: the offset
2400 for this sector is given here.
2402 CONFIG_ENV_OFFSET is used relative to CONFIG_SYS_FLASH_BASE.
2406 This is just another way to specify the start address of
2407 the flash sector containing the environment (instead of
2410 - CONFIG_ENV_SECT_SIZE:
2412 Size of the sector containing the environment.
2415 b) Sometimes flash chips have few, equal sized, BIG sectors.
2416 In such a case you don't want to spend a whole sector for
2421 If you use this in combination with CONFIG_ENV_IS_IN_FLASH
2422 and CONFIG_ENV_SECT_SIZE, you can specify to use only a part
2423 of this flash sector for the environment. This saves
2424 memory for the RAM copy of the environment.
2426 It may also save flash memory if you decide to use this
2427 when your environment is "embedded" within U-Boot code,
2428 since then the remainder of the flash sector could be used
2429 for U-Boot code. It should be pointed out that this is
2430 STRONGLY DISCOURAGED from a robustness point of view:
2431 updating the environment in flash makes it always
2432 necessary to erase the WHOLE sector. If something goes
2433 wrong before the contents has been restored from a copy in
2434 RAM, your target system will be dead.
2436 - CONFIG_ENV_ADDR_REDUND
2437 CONFIG_ENV_SIZE_REDUND
2439 These settings describe a second storage area used to hold
2440 a redundant copy of the environment data, so that there is
2441 a valid backup copy in case there is a power failure during
2442 a "saveenv" operation.
2444 BE CAREFUL! Any changes to the flash layout, and some changes to the
2445 source code will make it necessary to adapt <board>/u-boot.lds*
2449 - CONFIG_ENV_IS_IN_NVRAM:
2451 Define this if you have some non-volatile memory device
2452 (NVRAM, battery buffered SRAM) which you want to use for the
2458 These two #defines are used to determine the memory area you
2459 want to use for environment. It is assumed that this memory
2460 can just be read and written to, without any special
2463 BE CAREFUL! The first access to the environment happens quite early
2464 in U-Boot initalization (when we try to get the setting of for the
2465 console baudrate). You *MUST* have mapped your NVRAM area then, or
2468 Please note that even with NVRAM we still use a copy of the
2469 environment in RAM: we could work on NVRAM directly, but we want to
2470 keep settings there always unmodified except somebody uses "saveenv"
2471 to save the current settings.
2474 - CONFIG_ENV_IS_IN_EEPROM:
2476 Use this if you have an EEPROM or similar serial access
2477 device and a driver for it.
2479 - CONFIG_ENV_OFFSET:
2482 These two #defines specify the offset and size of the
2483 environment area within the total memory of your EEPROM.
2485 - CONFIG_SYS_I2C_EEPROM_ADDR:
2486 If defined, specified the chip address of the EEPROM device.
2487 The default address is zero.
2489 - CONFIG_SYS_EEPROM_PAGE_WRITE_BITS:
2490 If defined, the number of bits used to address bytes in a
2491 single page in the EEPROM device. A 64 byte page, for example
2492 would require six bits.
2494 - CONFIG_SYS_EEPROM_PAGE_WRITE_DELAY_MS:
2495 If defined, the number of milliseconds to delay between
2496 page writes. The default is zero milliseconds.
2498 - CONFIG_SYS_I2C_EEPROM_ADDR_LEN:
2499 The length in bytes of the EEPROM memory array address. Note
2500 that this is NOT the chip address length!
2502 - CONFIG_SYS_I2C_EEPROM_ADDR_OVERFLOW:
2503 EEPROM chips that implement "address overflow" are ones
2504 like Catalyst 24WC04/08/16 which has 9/10/11 bits of
2505 address and the extra bits end up in the "chip address" bit
2506 slots. This makes a 24WC08 (1Kbyte) chip look like four 256
2509 Note that we consider the length of the address field to
2510 still be one byte because the extra address bits are hidden
2511 in the chip address.
2513 - CONFIG_SYS_EEPROM_SIZE:
2514 The size in bytes of the EEPROM device.
2516 - CONFIG_ENV_EEPROM_IS_ON_I2C
2517 define this, if you have I2C and SPI activated, and your
2518 EEPROM, which holds the environment, is on the I2C bus.
2520 - CONFIG_I2C_ENV_EEPROM_BUS
2521 if you have an Environment on an EEPROM reached over
2522 I2C muxes, you can define here, how to reach this
2523 EEPROM. For example:
2525 #define CONFIG_I2C_ENV_EEPROM_BUS "pca9547:70:d\0"
2527 EEPROM which holds the environment, is reached over
2528 a pca9547 i2c mux with address 0x70, channel 3.
2530 - CONFIG_ENV_IS_IN_DATAFLASH:
2532 Define this if you have a DataFlash memory device which you
2533 want to use for the environment.
2535 - CONFIG_ENV_OFFSET:
2539 These three #defines specify the offset and size of the
2540 environment area within the total memory of your DataFlash placed
2541 at the specified address.
2543 - CONFIG_ENV_IS_IN_NAND:
2545 Define this if you have a NAND device which you want to use
2546 for the environment.
2548 - CONFIG_ENV_OFFSET:
2551 These two #defines specify the offset and size of the environment
2552 area within the first NAND device.
2554 - CONFIG_ENV_OFFSET_REDUND
2556 This setting describes a second storage area of CONFIG_ENV_SIZE
2557 size used to hold a redundant copy of the environment data,
2558 so that there is a valid backup copy in case there is a
2559 power failure during a "saveenv" operation.
2561 Note: CONFIG_ENV_OFFSET and CONFIG_ENV_OFFSET_REDUND must be aligned
2562 to a block boundary, and CONFIG_ENV_SIZE must be a multiple of
2563 the NAND devices block size.
2565 - CONFIG_NAND_ENV_DST
2567 Defines address in RAM to which the nand_spl code should copy the
2568 environment. If redundant environment is used, it will be copied to
2569 CONFIG_NAND_ENV_DST + CONFIG_ENV_SIZE.
2571 - CONFIG_SYS_SPI_INIT_OFFSET
2573 Defines offset to the initial SPI buffer area in DPRAM. The
2574 area is used at an early stage (ROM part) if the environment
2575 is configured to reside in the SPI EEPROM: We need a 520 byte
2576 scratch DPRAM area. It is used between the two initialization
2577 calls (spi_init_f() and spi_init_r()). A value of 0xB00 seems
2578 to be a good choice since it makes it far enough from the
2579 start of the data area as well as from the stack pointer.
2581 Please note that the environment is read-only until the monitor
2582 has been relocated to RAM and a RAM copy of the environment has been
2583 created; also, when using EEPROM you will have to use getenv_f()
2584 until then to read environment variables.
2586 The environment is protected by a CRC32 checksum. Before the monitor
2587 is relocated into RAM, as a result of a bad CRC you will be working
2588 with the compiled-in default environment - *silently*!!! [This is
2589 necessary, because the first environment variable we need is the
2590 "baudrate" setting for the console - if we have a bad CRC, we don't
2591 have any device yet where we could complain.]
2593 Note: once the monitor has been relocated, then it will complain if
2594 the default environment is used; a new CRC is computed as soon as you
2595 use the "saveenv" command to store a valid environment.
2597 - CONFIG_SYS_FAULT_ECHO_LINK_DOWN:
2598 Echo the inverted Ethernet link state to the fault LED.
2600 Note: If this option is active, then CONFIG_SYS_FAULT_MII_ADDR
2601 also needs to be defined.
2603 - CONFIG_SYS_FAULT_MII_ADDR:
2604 MII address of the PHY to check for the Ethernet link state.
2606 - CONFIG_NS16550_MIN_FUNCTIONS:
2607 Define this if you desire to only have use of the NS16550_init
2608 and NS16550_putc functions for the serial driver located at
2609 drivers/serial/ns16550.c. This option is useful for saving
2610 space for already greatly restricted images, including but not
2611 limited to NAND_SPL configurations.
2613 Low Level (hardware related) configuration options:
2614 ---------------------------------------------------
2616 - CONFIG_SYS_CACHELINE_SIZE:
2617 Cache Line Size of the CPU.
2619 - CONFIG_SYS_DEFAULT_IMMR:
2620 Default address of the IMMR after system reset.
2622 Needed on some 8260 systems (MPC8260ADS, PQ2FADS-ZU,
2623 and RPXsuper) to be able to adjust the position of
2624 the IMMR register after a reset.
2626 - Floppy Disk Support:
2627 CONFIG_SYS_FDC_DRIVE_NUMBER
2629 the default drive number (default value 0)
2631 CONFIG_SYS_ISA_IO_STRIDE
2633 defines the spacing between FDC chipset registers
2636 CONFIG_SYS_ISA_IO_OFFSET
2638 defines the offset of register from address. It
2639 depends on which part of the data bus is connected to
2640 the FDC chipset. (default value 0)
2642 If CONFIG_SYS_ISA_IO_STRIDE CONFIG_SYS_ISA_IO_OFFSET and
2643 CONFIG_SYS_FDC_DRIVE_NUMBER are undefined, they take their
2646 if CONFIG_SYS_FDC_HW_INIT is defined, then the function
2647 fdc_hw_init() is called at the beginning of the FDC
2648 setup. fdc_hw_init() must be provided by the board
2649 source code. It is used to make hardware dependant
2652 - CONFIG_SYS_IMMR: Physical address of the Internal Memory.
2653 DO NOT CHANGE unless you know exactly what you're
2654 doing! (11-4) [MPC8xx/82xx systems only]
2656 - CONFIG_SYS_INIT_RAM_ADDR:
2658 Start address of memory area that can be used for
2659 initial data and stack; please note that this must be
2660 writable memory that is working WITHOUT special
2661 initialization, i. e. you CANNOT use normal RAM which
2662 will become available only after programming the
2663 memory controller and running certain initialization
2666 U-Boot uses the following memory types:
2667 - MPC8xx and MPC8260: IMMR (internal memory of the CPU)
2668 - MPC824X: data cache
2669 - PPC4xx: data cache
2671 - CONFIG_SYS_GBL_DATA_OFFSET:
2673 Offset of the initial data structure in the memory
2674 area defined by CONFIG_SYS_INIT_RAM_ADDR. Usually
2675 CONFIG_SYS_GBL_DATA_OFFSET is chosen such that the initial
2676 data is located at the end of the available space
2677 (sometimes written as (CONFIG_SYS_INIT_RAM_END -
2678 CONFIG_SYS_INIT_DATA_SIZE), and the initial stack is just
2679 below that area (growing from (CONFIG_SYS_INIT_RAM_ADDR +
2680 CONFIG_SYS_GBL_DATA_OFFSET) downward.
2683 On the MPC824X (or other systems that use the data
2684 cache for initial memory) the address chosen for
2685 CONFIG_SYS_INIT_RAM_ADDR is basically arbitrary - it must
2686 point to an otherwise UNUSED address space between
2687 the top of RAM and the start of the PCI space.
2689 - CONFIG_SYS_SIUMCR: SIU Module Configuration (11-6)
2691 - CONFIG_SYS_SYPCR: System Protection Control (11-9)
2693 - CONFIG_SYS_TBSCR: Time Base Status and Control (11-26)
2695 - CONFIG_SYS_PISCR: Periodic Interrupt Status and Control (11-31)
2697 - CONFIG_SYS_PLPRCR: PLL, Low-Power, and Reset Control Register (15-30)
2699 - CONFIG_SYS_SCCR: System Clock and reset Control Register (15-27)
2701 - CONFIG_SYS_OR_TIMING_SDRAM:
2704 - CONFIG_SYS_MAMR_PTA:
2705 periodic timer for refresh
2707 - CONFIG_SYS_DER: Debug Event Register (37-47)
2709 - FLASH_BASE0_PRELIM, FLASH_BASE1_PRELIM, CONFIG_SYS_REMAP_OR_AM,
2710 CONFIG_SYS_PRELIM_OR_AM, CONFIG_SYS_OR_TIMING_FLASH, CONFIG_SYS_OR0_REMAP,
2711 CONFIG_SYS_OR0_PRELIM, CONFIG_SYS_BR0_PRELIM, CONFIG_SYS_OR1_REMAP, CONFIG_SYS_OR1_PRELIM,
2712 CONFIG_SYS_BR1_PRELIM:
2713 Memory Controller Definitions: BR0/1 and OR0/1 (FLASH)
2715 - SDRAM_BASE2_PRELIM, SDRAM_BASE3_PRELIM, SDRAM_MAX_SIZE,
2716 CONFIG_SYS_OR_TIMING_SDRAM, CONFIG_SYS_OR2_PRELIM, CONFIG_SYS_BR2_PRELIM,
2717 CONFIG_SYS_OR3_PRELIM, CONFIG_SYS_BR3_PRELIM:
2718 Memory Controller Definitions: BR2/3 and OR2/3 (SDRAM)
2720 - CONFIG_SYS_MAMR_PTA, CONFIG_SYS_MPTPR_2BK_4K, CONFIG_SYS_MPTPR_1BK_4K, CONFIG_SYS_MPTPR_2BK_8K,
2721 CONFIG_SYS_MPTPR_1BK_8K, CONFIG_SYS_MAMR_8COL, CONFIG_SYS_MAMR_9COL:
2722 Machine Mode Register and Memory Periodic Timer
2723 Prescaler definitions (SDRAM timing)
2725 - CONFIG_SYS_I2C_UCODE_PATCH, CONFIG_SYS_I2C_DPMEM_OFFSET [0x1FC0]:
2726 enable I2C microcode relocation patch (MPC8xx);
2727 define relocation offset in DPRAM [DSP2]
2729 - CONFIG_SYS_SMC_UCODE_PATCH, CONFIG_SYS_SMC_DPMEM_OFFSET [0x1FC0]:
2730 enable SMC microcode relocation patch (MPC8xx);
2731 define relocation offset in DPRAM [SMC1]
2733 - CONFIG_SYS_SPI_UCODE_PATCH, CONFIG_SYS_SPI_DPMEM_OFFSET [0x1FC0]:
2734 enable SPI microcode relocation patch (MPC8xx);
2735 define relocation offset in DPRAM [SCC4]
2737 - CONFIG_SYS_USE_OSCCLK:
2738 Use OSCM clock mode on MBX8xx board. Be careful,
2739 wrong setting might damage your board. Read
2740 doc/README.MBX before setting this variable!
2742 - CONFIG_SYS_CPM_POST_WORD_ADDR: (MPC8xx, MPC8260 only)
2743 Offset of the bootmode word in DPRAM used by post
2744 (Power On Self Tests). This definition overrides
2745 #define'd default value in commproc.h resp.
2748 - CONFIG_SYS_PCI_SLV_MEM_LOCAL, CONFIG_SYS_PCI_SLV_MEM_BUS, CONFIG_SYS_PICMR0_MASK_ATTRIB,
2749 CONFIG_SYS_PCI_MSTR0_LOCAL, CONFIG_SYS_PCIMSK0_MASK, CONFIG_SYS_PCI_MSTR1_LOCAL,
2750 CONFIG_SYS_PCIMSK1_MASK, CONFIG_SYS_PCI_MSTR_MEM_LOCAL, CONFIG_SYS_PCI_MSTR_MEM_BUS,
2751 CONFIG_SYS_CPU_PCI_MEM_START, CONFIG_SYS_PCI_MSTR_MEM_SIZE, CONFIG_SYS_POCMR0_MASK_ATTRIB,
2752 CONFIG_SYS_PCI_MSTR_MEMIO_LOCAL, CONFIG_SYS_PCI_MSTR_MEMIO_BUS, CPU_PCI_MEMIO_START,
2753 CONFIG_SYS_PCI_MSTR_MEMIO_SIZE, CONFIG_SYS_POCMR1_MASK_ATTRIB, CONFIG_SYS_PCI_MSTR_IO_LOCAL,
2754 CONFIG_SYS_PCI_MSTR_IO_BUS, CONFIG_SYS_CPU_PCI_IO_START, CONFIG_SYS_PCI_MSTR_IO_SIZE,
2755 CONFIG_SYS_POCMR2_MASK_ATTRIB: (MPC826x only)
2756 Overrides the default PCI memory map in arch/powerpc/cpu/mpc8260/pci.c if set.
2758 - CONFIG_PCI_DISABLE_PCIE:
2759 Disable PCI-Express on systems where it is supported but not
2763 Get DDR timing information from an I2C EEPROM. Common
2764 with pluggable memory modules such as SODIMMs
2767 I2C address of the SPD EEPROM
2769 - CONFIG_SYS_SPD_BUS_NUM
2770 If SPD EEPROM is on an I2C bus other than the first
2771 one, specify here. Note that the value must resolve
2772 to something your driver can deal with.
2774 - CONFIG_SYS_83XX_DDR_USES_CS0
2775 Only for 83xx systems. If specified, then DDR should
2776 be configured using CS0 and CS1 instead of CS2 and CS3.
2778 - CONFIG_ETHER_ON_FEC[12]
2779 Define to enable FEC[12] on a 8xx series processor.
2781 - CONFIG_FEC[12]_PHY
2782 Define to the hardcoded PHY address which corresponds
2783 to the given FEC; i. e.
2784 #define CONFIG_FEC1_PHY 4
2785 means that the PHY with address 4 is connected to FEC1
2787 When set to -1, means to probe for first available.
2789 - CONFIG_FEC[12]_PHY_NORXERR
2790 The PHY does not have a RXERR line (RMII only).
2791 (so program the FEC to ignore it).
2794 Enable RMII mode for all FECs.
2795 Note that this is a global option, we can't
2796 have one FEC in standard MII mode and another in RMII mode.
2798 - CONFIG_CRC32_VERIFY
2799 Add a verify option to the crc32 command.
2802 => crc32 -v <address> <count> <crc32>
2804 Where address/count indicate a memory area
2805 and crc32 is the correct crc32 which the
2809 Add the "loopw" memory command. This only takes effect if
2810 the memory commands are activated globally (CONFIG_CMD_MEM).
2813 Add the "mdc" and "mwc" memory commands. These are cyclic
2818 This command will print 4 bytes (10,11,12,13) each 500 ms.
2820 => mwc.l 100 12345678 10
2821 This command will write 12345678 to address 100 all 10 ms.
2823 This only takes effect if the memory commands are activated
2824 globally (CONFIG_CMD_MEM).
2826 - CONFIG_SKIP_LOWLEVEL_INIT
2827 - CONFIG_SKIP_RELOCATE_UBOOT
2829 [ARM only] If these variables are defined, then
2830 certain low level initializations (like setting up
2831 the memory controller) are omitted and/or U-Boot does
2832 not relocate itself into RAM.
2833 Normally these variables MUST NOT be defined. The
2834 only exception is when U-Boot is loaded (to RAM) by
2835 some other boot loader or by a debugger which
2836 performs these initializations itself.
2840 Modifies the behaviour of start.S when compiling a loader
2841 that is executed before the actual U-Boot. E.g. when
2842 compiling a NAND SPL.
2844 Building the Software:
2845 ======================
2847 Building U-Boot has been tested in several native build environments
2848 and in many different cross environments. Of course we cannot support
2849 all possibly existing versions of cross development tools in all
2850 (potentially obsolete) versions. In case of tool chain problems we
2851 recommend to use the ELDK (see http://www.denx.de/wiki/DULG/ELDK)
2852 which is extensively used to build and test U-Boot.
2854 If you are not using a native environment, it is assumed that you
2855 have GNU cross compiling tools available in your path. In this case,
2856 you must set the environment variable CROSS_COMPILE in your shell.
2857 Note that no changes to the Makefile or any other source files are
2858 necessary. For example using the ELDK on a 4xx CPU, please enter:
2860 $ CROSS_COMPILE=ppc_4xx-
2861 $ export CROSS_COMPILE
2863 Note: If you wish to generate Windows versions of the utilities in
2864 the tools directory you can use the MinGW toolchain
2865 (http://www.mingw.org). Set your HOST tools to the MinGW
2866 toolchain and execute 'make tools'. For example:
2868 $ make HOSTCC=i586-mingw32msvc-gcc HOSTSTRIP=i586-mingw32msvc-strip tools
2870 Binaries such as tools/mkimage.exe will be created which can
2871 be executed on computers running Windows.
2873 U-Boot is intended to be simple to build. After installing the
2874 sources you must configure U-Boot for one specific board type. This
2879 where "NAME_config" is the name of one of the existing configu-
2880 rations; see the main Makefile for supported names.
2882 Note: for some board special configuration names may exist; check if
2883 additional information is available from the board vendor; for
2884 instance, the TQM823L systems are available without (standard)
2885 or with LCD support. You can select such additional "features"
2886 when choosing the configuration, i. e.
2889 - will configure for a plain TQM823L, i. e. no LCD support
2891 make TQM823L_LCD_config
2892 - will configure for a TQM823L with U-Boot console on LCD
2897 Finally, type "make all", and you should get some working U-Boot
2898 images ready for download to / installation on your system:
2900 - "u-boot.bin" is a raw binary image
2901 - "u-boot" is an image in ELF binary format
2902 - "u-boot.srec" is in Motorola S-Record format
2904 By default the build is performed locally and the objects are saved
2905 in the source directory. One of the two methods can be used to change
2906 this behavior and build U-Boot to some external directory:
2908 1. Add O= to the make command line invocations:
2910 make O=/tmp/build distclean
2911 make O=/tmp/build NAME_config
2912 make O=/tmp/build all
2914 2. Set environment variable BUILD_DIR to point to the desired location:
2916 export BUILD_DIR=/tmp/build
2921 Note that the command line "O=" setting overrides the BUILD_DIR environment
2925 Please be aware that the Makefiles assume you are using GNU make, so
2926 for instance on NetBSD you might need to use "gmake" instead of
2930 If the system board that you have is not listed, then you will need
2931 to port U-Boot to your hardware platform. To do this, follow these
2934 1. Add a new configuration option for your board to the toplevel
2935 "Makefile" and to the "MAKEALL" script, using the existing
2936 entries as examples. Note that here and at many other places
2937 boards and other names are listed in alphabetical sort order. Please
2939 2. Create a new directory to hold your board specific code. Add any
2940 files you need. In your board directory, you will need at least
2941 the "Makefile", a "<board>.c", "flash.c" and "u-boot.lds".
2942 3. Create a new configuration file "include/configs/<board>.h" for
2944 3. If you're porting U-Boot to a new CPU, then also create a new
2945 directory to hold your CPU specific code. Add any files you need.
2946 4. Run "make <board>_config" with your new name.
2947 5. Type "make", and you should get a working "u-boot.srec" file
2948 to be installed on your target system.
2949 6. Debug and solve any problems that might arise.
2950 [Of course, this last step is much harder than it sounds.]
2953 Testing of U-Boot Modifications, Ports to New Hardware, etc.:
2954 ==============================================================
2956 If you have modified U-Boot sources (for instance added a new board
2957 or support for new devices, a new CPU, etc.) you are expected to
2958 provide feedback to the other developers. The feedback normally takes
2959 the form of a "patch", i. e. a context diff against a certain (latest
2960 official or latest in the git repository) version of U-Boot sources.
2962 But before you submit such a patch, please verify that your modifi-
2963 cation did not break existing code. At least make sure that *ALL* of
2964 the supported boards compile WITHOUT ANY compiler warnings. To do so,
2965 just run the "MAKEALL" script, which will configure and build U-Boot
2966 for ALL supported system. Be warned, this will take a while. You can
2967 select which (cross) compiler to use by passing a `CROSS_COMPILE'
2968 environment variable to the script, i. e. to use the ELDK cross tools
2971 CROSS_COMPILE=ppc_8xx- MAKEALL
2973 or to build on a native PowerPC system you can type
2975 CROSS_COMPILE=' ' MAKEALL
2977 When using the MAKEALL script, the default behaviour is to build
2978 U-Boot in the source directory. This location can be changed by
2979 setting the BUILD_DIR environment variable. Also, for each target
2980 built, the MAKEALL script saves two log files (<target>.ERR and
2981 <target>.MAKEALL) in the <source dir>/LOG directory. This default
2982 location can be changed by setting the MAKEALL_LOGDIR environment
2983 variable. For example:
2985 export BUILD_DIR=/tmp/build
2986 export MAKEALL_LOGDIR=/tmp/log
2987 CROSS_COMPILE=ppc_8xx- MAKEALL
2989 With the above settings build objects are saved in the /tmp/build,
2990 log files are saved in the /tmp/log and the source tree remains clean
2991 during the whole build process.
2994 See also "U-Boot Porting Guide" below.
2997 Monitor Commands - Overview:
2998 ============================
3000 go - start application at address 'addr'
3001 run - run commands in an environment variable
3002 bootm - boot application image from memory
3003 bootp - boot image via network using BootP/TFTP protocol
3004 tftpboot- boot image via network using TFTP protocol
3005 and env variables "ipaddr" and "serverip"
3006 (and eventually "gatewayip")
3007 rarpboot- boot image via network using RARP/TFTP protocol
3008 diskboot- boot from IDE devicebootd - boot default, i.e., run 'bootcmd'
3009 loads - load S-Record file over serial line
3010 loadb - load binary file over serial line (kermit mode)
3012 mm - memory modify (auto-incrementing)
3013 nm - memory modify (constant address)
3014 mw - memory write (fill)
3016 cmp - memory compare
3017 crc32 - checksum calculation
3018 i2c - I2C sub-system
3019 sspi - SPI utility commands
3020 base - print or set address offset
3021 printenv- print environment variables
3022 setenv - set environment variables
3023 saveenv - save environment variables to persistent storage
3024 protect - enable or disable FLASH write protection
3025 erase - erase FLASH memory
3026 flinfo - print FLASH memory information
3027 bdinfo - print Board Info structure
3028 iminfo - print header information for application image
3029 coninfo - print console devices and informations
3030 ide - IDE sub-system
3031 loop - infinite loop on address range
3032 loopw - infinite write loop on address range
3033 mtest - simple RAM test
3034 icache - enable or disable instruction cache
3035 dcache - enable or disable data cache
3036 reset - Perform RESET of the CPU
3037 echo - echo args to console
3038 version - print monitor version
3039 help - print online help
3040 ? - alias for 'help'
3043 Monitor Commands - Detailed Description:
3044 ========================================
3048 For now: just type "help <command>".
3051 Environment Variables:
3052 ======================
3054 U-Boot supports user configuration using Environment Variables which
3055 can be made persistent by saving to Flash memory.
3057 Environment Variables are set using "setenv", printed using
3058 "printenv", and saved to Flash using "saveenv". Using "setenv"
3059 without a value can be used to delete a variable from the
3060 environment. As long as you don't save the environment you are
3061 working with an in-memory copy. In case the Flash area containing the
3062 environment is erased by accident, a default environment is provided.
3064 Some configuration options can be set using Environment Variables.
3066 List of environment variables (most likely not complete):
3068 baudrate - see CONFIG_BAUDRATE
3070 bootdelay - see CONFIG_BOOTDELAY
3072 bootcmd - see CONFIG_BOOTCOMMAND
3074 bootargs - Boot arguments when booting an RTOS image
3076 bootfile - Name of the image to load with TFTP
3078 bootm_low - Memory range available for image processing in the bootm
3079 command can be restricted. This variable is given as
3080 a hexadecimal number and defines lowest address allowed
3081 for use by the bootm command. See also "bootm_size"
3082 environment variable. Address defined by "bootm_low" is
3083 also the base of the initial memory mapping for the Linux
3084 kernel -- see the description of CONFIG_SYS_BOOTMAPSZ.
3086 bootm_size - Memory range available for image processing in the bootm
3087 command can be restricted. This variable is given as
3088 a hexadecimal number and defines the size of the region
3089 allowed for use by the bootm command. See also "bootm_low"
3090 environment variable.
3092 updatefile - Location of the software update file on a TFTP server, used
3093 by the automatic software update feature. Please refer to
3094 documentation in doc/README.update for more details.
3096 autoload - if set to "no" (any string beginning with 'n'),
3097 "bootp" will just load perform a lookup of the
3098 configuration from the BOOTP server, but not try to
3099 load any image using TFTP
3101 autostart - if set to "yes", an image loaded using the "bootp",
3102 "rarpboot", "tftpboot" or "diskboot" commands will
3103 be automatically started (by internally calling
3106 If set to "no", a standalone image passed to the
3107 "bootm" command will be copied to the load address
3108 (and eventually uncompressed), but NOT be started.
3109 This can be used to load and uncompress arbitrary
3112 i2cfast - (PPC405GP|PPC405EP only)
3113 if set to 'y' configures Linux I2C driver for fast
3114 mode (400kHZ). This environment variable is used in
3115 initialization code. So, for changes to be effective
3116 it must be saved and board must be reset.
3118 initrd_high - restrict positioning of initrd images:
3119 If this variable is not set, initrd images will be
3120 copied to the highest possible address in RAM; this
3121 is usually what you want since it allows for
3122 maximum initrd size. If for some reason you want to
3123 make sure that the initrd image is loaded below the
3124 CONFIG_SYS_BOOTMAPSZ limit, you can set this environment
3125 variable to a value of "no" or "off" or "0".
3126 Alternatively, you can set it to a maximum upper
3127 address to use (U-Boot will still check that it
3128 does not overwrite the U-Boot stack and data).
3130 For instance, when you have a system with 16 MB
3131 RAM, and want to reserve 4 MB from use by Linux,
3132 you can do this by adding "mem=12M" to the value of
3133 the "bootargs" variable. However, now you must make
3134 sure that the initrd image is placed in the first
3135 12 MB as well - this can be done with
3137 setenv initrd_high 00c00000
3139 If you set initrd_high to 0xFFFFFFFF, this is an
3140 indication to U-Boot that all addresses are legal
3141 for the Linux kernel, including addresses in flash
3142 memory. In this case U-Boot will NOT COPY the
3143 ramdisk at all. This may be useful to reduce the
3144 boot time on your system, but requires that this
3145 feature is supported by your Linux kernel.
3147 ipaddr - IP address; needed for tftpboot command
3149 loadaddr - Default load address for commands like "bootp",
3150 "rarpboot", "tftpboot", "loadb" or "diskboot"
3152 loads_echo - see CONFIG_LOADS_ECHO
3154 serverip - TFTP server IP address; needed for tftpboot command
3156 bootretry - see CONFIG_BOOT_RETRY_TIME
3158 bootdelaykey - see CONFIG_AUTOBOOT_DELAY_STR
3160 bootstopkey - see CONFIG_AUTOBOOT_STOP_STR
3162 ethprime - When CONFIG_NET_MULTI is enabled controls which
3163 interface is used first.
3165 ethact - When CONFIG_NET_MULTI is enabled controls which
3166 interface is currently active. For example you
3167 can do the following
3169 => setenv ethact FEC
3170 => ping 192.168.0.1 # traffic sent on FEC
3171 => setenv ethact SCC
3172 => ping 10.0.0.1 # traffic sent on SCC
3174 ethrotate - When set to "no" U-Boot does not go through all
3175 available network interfaces.
3176 It just stays at the currently selected interface.
3178 netretry - When set to "no" each network operation will
3179 either succeed or fail without retrying.
3180 When set to "once" the network operation will
3181 fail when all the available network interfaces
3182 are tried once without success.
3183 Useful on scripts which control the retry operation
3186 npe_ucode - set load address for the NPE microcode
3188 tftpsrcport - If this is set, the value is used for TFTP's
3191 tftpdstport - If this is set, the value is used for TFTP's UDP
3192 destination port instead of the Well Know Port 69.
3194 tftpblocksize - Block size to use for TFTP transfers; if not set,
3195 we use the TFTP server's default block size
3197 tftptimeout - Retransmission timeout for TFTP packets (in milli-
3198 seconds, minimum value is 1000 = 1 second). Defines
3199 when a packet is considered to be lost so it has to
3200 be retransmitted. The default is 5000 = 5 seconds.
3201 Lowering this value may make downloads succeed
3202 faster in networks with high packet loss rates or
3203 with unreliable TFTP servers.
3205 vlan - When set to a value < 4095 the traffic over
3206 Ethernet is encapsulated/received over 802.1q
3209 The following environment variables may be used and automatically
3210 updated by the network boot commands ("bootp" and "rarpboot"),
3211 depending the information provided by your boot server:
3213 bootfile - see above
3214 dnsip - IP address of your Domain Name Server
3215 dnsip2 - IP address of your secondary Domain Name Server
3216 gatewayip - IP address of the Gateway (Router) to use
3217 hostname - Target hostname
3219 netmask - Subnet Mask
3220 rootpath - Pathname of the root filesystem on the NFS server
3221 serverip - see above
3224 There are two special Environment Variables:
3226 serial# - contains hardware identification information such
3227 as type string and/or serial number
3228 ethaddr - Ethernet address
3230 These variables can be set only once (usually during manufacturing of
3231 the board). U-Boot refuses to delete or overwrite these variables
3232 once they have been set once.
3235 Further special Environment Variables:
3237 ver - Contains the U-Boot version string as printed
3238 with the "version" command. This variable is
3239 readonly (see CONFIG_VERSION_VARIABLE).
3242 Please note that changes to some configuration parameters may take
3243 only effect after the next boot (yes, that's just like Windoze :-).
3246 Command Line Parsing:
3247 =====================
3249 There are two different command line parsers available with U-Boot:
3250 the old "simple" one, and the much more powerful "hush" shell:
3252 Old, simple command line parser:
3253 --------------------------------
3255 - supports environment variables (through setenv / saveenv commands)
3256 - several commands on one line, separated by ';'
3257 - variable substitution using "... ${name} ..." syntax
3258 - special characters ('$', ';') can be escaped by prefixing with '\',
3260 setenv bootcmd bootm \${address}
3261 - You can also escape text by enclosing in single apostrophes, for example:
3262 setenv addip 'setenv bootargs $bootargs ip=$ipaddr:$serverip:$gatewayip:$netmask:$hostname::off'
3267 - similar to Bourne shell, with control structures like
3268 if...then...else...fi, for...do...done; while...do...done,
3269 until...do...done, ...
3270 - supports environment ("global") variables (through setenv / saveenv
3271 commands) and local shell variables (through standard shell syntax
3272 "name=value"); only environment variables can be used with "run"
3278 (1) If a command line (or an environment variable executed by a "run"
3279 command) contains several commands separated by semicolon, and
3280 one of these commands fails, then the remaining commands will be
3283 (2) If you execute several variables with one call to run (i. e.
3284 calling run with a list of variables as arguments), any failing
3285 command will cause "run" to terminate, i. e. the remaining
3286 variables are not executed.
3288 Note for Redundant Ethernet Interfaces:
3289 =======================================
3291 Some boards come with redundant Ethernet interfaces; U-Boot supports
3292 such configurations and is capable of automatic selection of a
3293 "working" interface when needed. MAC assignment works as follows:
3295 Network interfaces are numbered eth0, eth1, eth2, ... Corresponding
3296 MAC addresses can be stored in the environment as "ethaddr" (=>eth0),
3297 "eth1addr" (=>eth1), "eth2addr", ...
3299 If the network interface stores some valid MAC address (for instance
3300 in SROM), this is used as default address if there is NO correspon-
3301 ding setting in the environment; if the corresponding environment
3302 variable is set, this overrides the settings in the card; that means:
3304 o If the SROM has a valid MAC address, and there is no address in the
3305 environment, the SROM's address is used.
3307 o If there is no valid address in the SROM, and a definition in the
3308 environment exists, then the value from the environment variable is
3311 o If both the SROM and the environment contain a MAC address, and
3312 both addresses are the same, this MAC address is used.
3314 o If both the SROM and the environment contain a MAC address, and the
3315 addresses differ, the value from the environment is used and a
3318 o If neither SROM nor the environment contain a MAC address, an error
3321 If Ethernet drivers implement the 'write_hwaddr' function, valid MAC addresses
3322 will be programmed into hardware as part of the initialization process. This
3323 may be skipped by setting the appropriate 'ethmacskip' environment variable.
3324 The naming convention is as follows:
3325 "ethmacskip" (=>eth0), "eth1macskip" (=>eth1) etc.
3330 U-Boot is capable of booting (and performing other auxiliary operations on)
3331 images in two formats:
3333 New uImage format (FIT)
3334 -----------------------
3336 Flexible and powerful format based on Flattened Image Tree -- FIT (similar
3337 to Flattened Device Tree). It allows the use of images with multiple
3338 components (several kernels, ramdisks, etc.), with contents protected by
3339 SHA1, MD5 or CRC32. More details are found in the doc/uImage.FIT directory.
3345 Old image format is based on binary files which can be basically anything,
3346 preceded by a special header; see the definitions in include/image.h for
3347 details; basically, the header defines the following image properties:
3349 * Target Operating System (Provisions for OpenBSD, NetBSD, FreeBSD,
3350 4.4BSD, Linux, SVR4, Esix, Solaris, Irix, SCO, Dell, NCR, VxWorks,
3351 LynxOS, pSOS, QNX, RTEMS, INTEGRITY;
3352 Currently supported: Linux, NetBSD, VxWorks, QNX, RTEMS, LynxOS,
3354 * Target CPU Architecture (Provisions for Alpha, ARM, AVR32, Intel x86,
3355 IA64, MIPS, Nios II, PowerPC, IBM S390, SuperH, Sparc, Sparc 64 Bit;
3356 Currently supported: ARM, AVR32, Intel x86, MIPS, Nios II, PowerPC).
3357 * Compression Type (uncompressed, gzip, bzip2)
3363 The header is marked by a special Magic Number, and both the header
3364 and the data portions of the image are secured against corruption by
3371 Although U-Boot should support any OS or standalone application
3372 easily, the main focus has always been on Linux during the design of
3375 U-Boot includes many features that so far have been part of some
3376 special "boot loader" code within the Linux kernel. Also, any
3377 "initrd" images to be used are no longer part of one big Linux image;
3378 instead, kernel and "initrd" are separate images. This implementation
3379 serves several purposes:
3381 - the same features can be used for other OS or standalone
3382 applications (for instance: using compressed images to reduce the
3383 Flash memory footprint)
3385 - it becomes much easier to port new Linux kernel versions because
3386 lots of low-level, hardware dependent stuff are done by U-Boot
3388 - the same Linux kernel image can now be used with different "initrd"
3389 images; of course this also means that different kernel images can
3390 be run with the same "initrd". This makes testing easier (you don't
3391 have to build a new "zImage.initrd" Linux image when you just
3392 change a file in your "initrd"). Also, a field-upgrade of the
3393 software is easier now.
3399 Porting Linux to U-Boot based systems:
3400 ---------------------------------------
3402 U-Boot cannot save you from doing all the necessary modifications to
3403 configure the Linux device drivers for use with your target hardware
3404 (no, we don't intend to provide a full virtual machine interface to
3407 But now you can ignore ALL boot loader code (in arch/powerpc/mbxboot).
3409 Just make sure your machine specific header file (for instance
3410 include/asm-ppc/tqm8xx.h) includes the same definition of the Board
3411 Information structure as we define in include/asm-<arch>/u-boot.h,
3412 and make sure that your definition of IMAP_ADDR uses the same value
3413 as your U-Boot configuration in CONFIG_SYS_IMMR.
3416 Configuring the Linux kernel:
3417 -----------------------------
3419 No specific requirements for U-Boot. Make sure you have some root
3420 device (initial ramdisk, NFS) for your target system.
3423 Building a Linux Image:
3424 -----------------------
3426 With U-Boot, "normal" build targets like "zImage" or "bzImage" are
3427 not used. If you use recent kernel source, a new build target
3428 "uImage" will exist which automatically builds an image usable by
3429 U-Boot. Most older kernels also have support for a "pImage" target,
3430 which was introduced for our predecessor project PPCBoot and uses a
3431 100% compatible format.
3440 The "uImage" build target uses a special tool (in 'tools/mkimage') to
3441 encapsulate a compressed Linux kernel image with header information,
3442 CRC32 checksum etc. for use with U-Boot. This is what we are doing:
3444 * build a standard "vmlinux" kernel image (in ELF binary format):
3446 * convert the kernel into a raw binary image:
3448 ${CROSS_COMPILE}-objcopy -O binary \
3449 -R .note -R .comment \
3450 -S vmlinux linux.bin
3452 * compress the binary image:
3456 * package compressed binary image for U-Boot:
3458 mkimage -A ppc -O linux -T kernel -C gzip \
3459 -a 0 -e 0 -n "Linux Kernel Image" \
3460 -d linux.bin.gz uImage
3463 The "mkimage" tool can also be used to create ramdisk images for use
3464 with U-Boot, either separated from the Linux kernel image, or
3465 combined into one file. "mkimage" encapsulates the images with a 64
3466 byte header containing information about target architecture,
3467 operating system, image type, compression method, entry points, time
3468 stamp, CRC32 checksums, etc.
3470 "mkimage" can be called in two ways: to verify existing images and
3471 print the header information, or to build new images.
3473 In the first form (with "-l" option) mkimage lists the information
3474 contained in the header of an existing U-Boot image; this includes
3475 checksum verification:
3477 tools/mkimage -l image
3478 -l ==> list image header information
3480 The second form (with "-d" option) is used to build a U-Boot image
3481 from a "data file" which is used as image payload:
3483 tools/mkimage -A arch -O os -T type -C comp -a addr -e ep \
3484 -n name -d data_file image
3485 -A ==> set architecture to 'arch'
3486 -O ==> set operating system to 'os'
3487 -T ==> set image type to 'type'
3488 -C ==> set compression type 'comp'
3489 -a ==> set load address to 'addr' (hex)
3490 -e ==> set entry point to 'ep' (hex)
3491 -n ==> set image name to 'name'
3492 -d ==> use image data from 'datafile'
3494 Right now, all Linux kernels for PowerPC systems use the same load
3495 address (0x00000000), but the entry point address depends on the
3498 - 2.2.x kernels have the entry point at 0x0000000C,
3499 - 2.3.x and later kernels have the entry point at 0x00000000.
3501 So a typical call to build a U-Boot image would read:
3503 -> tools/mkimage -n '2.4.4 kernel for TQM850L' \
3504 > -A ppc -O linux -T kernel -C gzip -a 0 -e 0 \
3505 > -d /opt/elsk/ppc_8xx/usr/src/linux-2.4.4/arch/powerpc/coffboot/vmlinux.gz \
3506 > examples/uImage.TQM850L
3507 Image Name: 2.4.4 kernel for TQM850L
3508 Created: Wed Jul 19 02:34:59 2000
3509 Image Type: PowerPC Linux Kernel Image (gzip compressed)
3510 Data Size: 335725 Bytes = 327.86 kB = 0.32 MB
3511 Load Address: 0x00000000
3512 Entry Point: 0x00000000
3514 To verify the contents of the image (or check for corruption):
3516 -> tools/mkimage -l examples/uImage.TQM850L
3517 Image Name: 2.4.4 kernel for TQM850L
3518 Created: Wed Jul 19 02:34:59 2000
3519 Image Type: PowerPC Linux Kernel Image (gzip compressed)
3520 Data Size: 335725 Bytes = 327.86 kB = 0.32 MB
3521 Load Address: 0x00000000
3522 Entry Point: 0x00000000
3524 NOTE: for embedded systems where boot time is critical you can trade
3525 speed for memory and install an UNCOMPRESSED image instead: this
3526 needs more space in Flash, but boots much faster since it does not
3527 need to be uncompressed:
3529 -> gunzip /opt/elsk/ppc_8xx/usr/src/linux-2.4.4/arch/powerpc/coffboot/vmlinux.gz
3530 -> tools/mkimage -n '2.4.4 kernel for TQM850L' \
3531 > -A ppc -O linux -T kernel -C none -a 0 -e 0 \
3532 > -d /opt/elsk/ppc_8xx/usr/src/linux-2.4.4/arch/powerpc/coffboot/vmlinux \
3533 > examples/uImage.TQM850L-uncompressed
3534 Image Name: 2.4.4 kernel for TQM850L
3535 Created: Wed Jul 19 02:34:59 2000
3536 Image Type: PowerPC Linux Kernel Image (uncompressed)
3537 Data Size: 792160 Bytes = 773.59 kB = 0.76 MB
3538 Load Address: 0x00000000
3539 Entry Point: 0x00000000
3542 Similar you can build U-Boot images from a 'ramdisk.image.gz' file
3543 when your kernel is intended to use an initial ramdisk:
3545 -> tools/mkimage -n 'Simple Ramdisk Image' \
3546 > -A ppc -O linux -T ramdisk -C gzip \
3547 > -d /LinuxPPC/images/SIMPLE-ramdisk.image.gz examples/simple-initrd
3548 Image Name: Simple Ramdisk Image
3549 Created: Wed Jan 12 14:01:50 2000
3550 Image Type: PowerPC Linux RAMDisk Image (gzip compressed)
3551 Data Size: 566530 Bytes = 553.25 kB = 0.54 MB
3552 Load Address: 0x00000000
3553 Entry Point: 0x00000000
3556 Installing a Linux Image:
3557 -------------------------
3559 To downloading a U-Boot image over the serial (console) interface,
3560 you must convert the image to S-Record format:
3562 objcopy -I binary -O srec examples/image examples/image.srec
3564 The 'objcopy' does not understand the information in the U-Boot
3565 image header, so the resulting S-Record file will be relative to
3566 address 0x00000000. To load it to a given address, you need to
3567 specify the target address as 'offset' parameter with the 'loads'
3570 Example: install the image to address 0x40100000 (which on the
3571 TQM8xxL is in the first Flash bank):
3573 => erase 40100000 401FFFFF
3579 ## Ready for S-Record download ...
3580 ~>examples/image.srec
3581 1 2 3 4 5 6 7 8 9 10 11 12 13 ...
3583 15989 15990 15991 15992
3584 [file transfer complete]
3586 ## Start Addr = 0x00000000
3589 You can check the success of the download using the 'iminfo' command;
3590 this includes a checksum verification so you can be sure no data
3591 corruption happened:
3595 ## Checking Image at 40100000 ...
3596 Image Name: 2.2.13 for initrd on TQM850L
3597 Image Type: PowerPC Linux Kernel Image (gzip compressed)
3598 Data Size: 335725 Bytes = 327 kB = 0 MB
3599 Load Address: 00000000
3600 Entry Point: 0000000c
3601 Verifying Checksum ... OK
3607 The "bootm" command is used to boot an application that is stored in
3608 memory (RAM or Flash). In case of a Linux kernel image, the contents
3609 of the "bootargs" environment variable is passed to the kernel as
3610 parameters. You can check and modify this variable using the
3611 "printenv" and "setenv" commands:
3614 => printenv bootargs
3615 bootargs=root=/dev/ram
3617 => setenv bootargs root=/dev/nfs rw nfsroot=10.0.0.2:/LinuxPPC nfsaddrs=10.0.0.99:10.0.0.2
3619 => printenv bootargs
3620 bootargs=root=/dev/nfs rw nfsroot=10.0.0.2:/LinuxPPC nfsaddrs=10.0.0.99:10.0.0.2
3623 ## Booting Linux kernel at 40020000 ...
3624 Image Name: 2.2.13 for NFS on TQM850L
3625 Image Type: PowerPC Linux Kernel Image (gzip compressed)
3626 Data Size: 381681 Bytes = 372 kB = 0 MB
3627 Load Address: 00000000
3628 Entry Point: 0000000c
3629 Verifying Checksum ... OK
3630 Uncompressing Kernel Image ... OK
3631 Linux version 2.2.13 (wd@denx.local.net) (gcc version 2.95.2 19991024 (release)) #1 Wed Jul 19 02:35:17 MEST 2000
3632 Boot arguments: root=/dev/nfs rw nfsroot=10.0.0.2:/LinuxPPC nfsaddrs=10.0.0.99:10.0.0.2
3633 time_init: decrementer frequency = 187500000/60
3634 Calibrating delay loop... 49.77 BogoMIPS
3635 Memory: 15208k available (700k kernel code, 444k data, 32k init) [c0000000,c1000000]
3638 If you want to boot a Linux kernel with initial RAM disk, you pass
3639 the memory addresses of both the kernel and the initrd image (PPBCOOT
3640 format!) to the "bootm" command:
3642 => imi 40100000 40200000
3644 ## Checking Image at 40100000 ...
3645 Image Name: 2.2.13 for initrd on TQM850L
3646 Image Type: PowerPC Linux Kernel Image (gzip compressed)
3647 Data Size: 335725 Bytes = 327 kB = 0 MB
3648 Load Address: 00000000
3649 Entry Point: 0000000c
3650 Verifying Checksum ... OK
3652 ## Checking Image at 40200000 ...
3653 Image Name: Simple Ramdisk Image
3654 Image Type: PowerPC Linux RAMDisk Image (gzip compressed)
3655 Data Size: 566530 Bytes = 553 kB = 0 MB
3656 Load Address: 00000000
3657 Entry Point: 00000000
3658 Verifying Checksum ... OK
3660 => bootm 40100000 40200000
3661 ## Booting Linux kernel at 40100000 ...
3662 Image Name: 2.2.13 for initrd on TQM850L
3663 Image Type: PowerPC Linux Kernel Image (gzip compressed)
3664 Data Size: 335725 Bytes = 327 kB = 0 MB
3665 Load Address: 00000000
3666 Entry Point: 0000000c
3667 Verifying Checksum ... OK
3668 Uncompressing Kernel Image ... OK
3669 ## Loading RAMDisk Image at 40200000 ...
3670 Image Name: Simple Ramdisk Image
3671 Image Type: PowerPC Linux RAMDisk Image (gzip compressed)
3672 Data Size: 566530 Bytes = 553 kB = 0 MB
3673 Load Address: 00000000
3674 Entry Point: 00000000
3675 Verifying Checksum ... OK
3676 Loading Ramdisk ... OK
3677 Linux version 2.2.13 (wd@denx.local.net) (gcc version 2.95.2 19991024 (release)) #1 Wed Jul 19 02:32:08 MEST 2000
3678 Boot arguments: root=/dev/ram
3679 time_init: decrementer frequency = 187500000/60
3680 Calibrating delay loop... 49.77 BogoMIPS
3682 RAMDISK: Compressed image found at block 0
3683 VFS: Mounted root (ext2 filesystem).
3687 Boot Linux and pass a flat device tree:
3690 First, U-Boot must be compiled with the appropriate defines. See the section
3691 titled "Linux Kernel Interface" above for a more in depth explanation. The
3692 following is an example of how to start a kernel and pass an updated
3698 oft=oftrees/mpc8540ads.dtb
3699 => tftp $oftaddr $oft
3700 Speed: 1000, full duplex
3702 TFTP from server 192.168.1.1; our IP address is 192.168.1.101
3703 Filename 'oftrees/mpc8540ads.dtb'.
3704 Load address: 0x300000
3707 Bytes transferred = 4106 (100a hex)
3708 => tftp $loadaddr $bootfile
3709 Speed: 1000, full duplex
3711 TFTP from server 192.168.1.1; our IP address is 192.168.1.2
3713 Load address: 0x200000
3714 Loading:############
3716 Bytes transferred = 1029407 (fb51f hex)
3721 => bootm $loadaddr - $oftaddr
3722 ## Booting image at 00200000 ...
3723 Image Name: Linux-2.6.17-dirty
3724 Image Type: PowerPC Linux Kernel Image (gzip compressed)
3725 Data Size: 1029343 Bytes = 1005.2 kB
3726 Load Address: 00000000
3727 Entry Point: 00000000
3728 Verifying Checksum ... OK
3729 Uncompressing Kernel Image ... OK
3730 Booting using flat device tree at 0x300000
3731 Using MPC85xx ADS machine description
3732 Memory CAM mapping: CAM0=256Mb, CAM1=256Mb, CAM2=0Mb residual: 0Mb
3736 More About U-Boot Image Types:
3737 ------------------------------
3739 U-Boot supports the following image types:
3741 "Standalone Programs" are directly runnable in the environment
3742 provided by U-Boot; it is expected that (if they behave
3743 well) you can continue to work in U-Boot after return from
3744 the Standalone Program.
3745 "OS Kernel Images" are usually images of some Embedded OS which
3746 will take over control completely. Usually these programs
3747 will install their own set of exception handlers, device
3748 drivers, set up the MMU, etc. - this means, that you cannot
3749 expect to re-enter U-Boot except by resetting the CPU.
3750 "RAMDisk Images" are more or less just data blocks, and their
3751 parameters (address, size) are passed to an OS kernel that is
3753 "Multi-File Images" contain several images, typically an OS
3754 (Linux) kernel image and one or more data images like
3755 RAMDisks. This construct is useful for instance when you want
3756 to boot over the network using BOOTP etc., where the boot
3757 server provides just a single image file, but you want to get
3758 for instance an OS kernel and a RAMDisk image.
3760 "Multi-File Images" start with a list of image sizes, each
3761 image size (in bytes) specified by an "uint32_t" in network
3762 byte order. This list is terminated by an "(uint32_t)0".
3763 Immediately after the terminating 0 follow the images, one by
3764 one, all aligned on "uint32_t" boundaries (size rounded up to
3765 a multiple of 4 bytes).
3767 "Firmware Images" are binary images containing firmware (like
3768 U-Boot or FPGA images) which usually will be programmed to
3771 "Script files" are command sequences that will be executed by
3772 U-Boot's command interpreter; this feature is especially
3773 useful when you configure U-Boot to use a real shell (hush)
3774 as command interpreter.
3780 One of the features of U-Boot is that you can dynamically load and
3781 run "standalone" applications, which can use some resources of
3782 U-Boot like console I/O functions or interrupt services.
3784 Two simple examples are included with the sources:
3789 'examples/hello_world.c' contains a small "Hello World" Demo
3790 application; it is automatically compiled when you build U-Boot.
3791 It's configured to run at address 0x00040004, so you can play with it
3795 ## Ready for S-Record download ...
3796 ~>examples/hello_world.srec
3797 1 2 3 4 5 6 7 8 9 10 11 ...
3798 [file transfer complete]
3800 ## Start Addr = 0x00040004
3802 => go 40004 Hello World! This is a test.
3803 ## Starting application at 0x00040004 ...
3814 Hit any key to exit ...
3816 ## Application terminated, rc = 0x0
3818 Another example, which demonstrates how to register a CPM interrupt
3819 handler with the U-Boot code, can be found in 'examples/timer.c'.
3820 Here, a CPM timer is set up to generate an interrupt every second.
3821 The interrupt service routine is trivial, just printing a '.'
3822 character, but this is just a demo program. The application can be
3823 controlled by the following keys:
3825 ? - print current values og the CPM Timer registers
3826 b - enable interrupts and start timer
3827 e - stop timer and disable interrupts
3828 q - quit application
3831 ## Ready for S-Record download ...
3832 ~>examples/timer.srec
3833 1 2 3 4 5 6 7 8 9 10 11 ...
3834 [file transfer complete]
3836 ## Start Addr = 0x00040004
3839 ## Starting application at 0x00040004 ...
3842 tgcr @ 0xfff00980, tmr @ 0xfff00990, trr @ 0xfff00994, tcr @ 0xfff00998, tcn @ 0xfff0099c, ter @ 0xfff009b0
3845 [q, b, e, ?] Set interval 1000000 us
3848 [q, b, e, ?] ........
3849 tgcr=0x1, tmr=0xff1c, trr=0x3d09, tcr=0x0, tcn=0xef6, ter=0x0
3852 tgcr=0x1, tmr=0xff1c, trr=0x3d09, tcr=0x0, tcn=0x2ad4, ter=0x0
3855 tgcr=0x1, tmr=0xff1c, trr=0x3d09, tcr=0x0, tcn=0x1efc, ter=0x0
3858 tgcr=0x1, tmr=0xff1c, trr=0x3d09, tcr=0x0, tcn=0x169d, ter=0x0
3860 [q, b, e, ?] ...Stopping timer
3862 [q, b, e, ?] ## Application terminated, rc = 0x0
3868 Over time, many people have reported problems when trying to use the
3869 "minicom" terminal emulation program for serial download. I (wd)
3870 consider minicom to be broken, and recommend not to use it. Under
3871 Unix, I recommend to use C-Kermit for general purpose use (and
3872 especially for kermit binary protocol download ("loadb" command), and
3873 use "cu" for S-Record download ("loads" command).
3875 Nevertheless, if you absolutely want to use it try adding this
3876 configuration to your "File transfer protocols" section:
3878 Name Program Name U/D FullScr IO-Red. Multi
3879 X kermit /usr/bin/kermit -i -l %l -s Y U Y N N
3880 Y kermit /usr/bin/kermit -i -l %l -r N D Y N N
3886 Starting at version 0.9.2, U-Boot supports NetBSD both as host
3887 (build U-Boot) and target system (boots NetBSD/mpc8xx).
3889 Building requires a cross environment; it is known to work on
3890 NetBSD/i386 with the cross-powerpc-netbsd-1.3 package (you will also
3891 need gmake since the Makefiles are not compatible with BSD make).
3892 Note that the cross-powerpc package does not install include files;
3893 attempting to build U-Boot will fail because <machine/ansi.h> is
3894 missing. This file has to be installed and patched manually:
3896 # cd /usr/pkg/cross/powerpc-netbsd/include
3898 # ln -s powerpc machine
3899 # cp /usr/src/sys/arch/powerpc/include/ansi.h powerpc/ansi.h
3900 # ${EDIT} powerpc/ansi.h ## must remove __va_list, _BSD_VA_LIST
3902 Native builds *don't* work due to incompatibilities between native
3903 and U-Boot include files.
3905 Booting assumes that (the first part of) the image booted is a
3906 stage-2 loader which in turn loads and then invokes the kernel
3907 proper. Loader sources will eventually appear in the NetBSD source
3908 tree (probably in sys/arc/mpc8xx/stand/u-boot_stage2/); in the
3909 meantime, see ftp://ftp.denx.de/pub/u-boot/ppcboot_stage2.tar.gz
3912 Implementation Internals:
3913 =========================
3915 The following is not intended to be a complete description of every
3916 implementation detail. However, it should help to understand the
3917 inner workings of U-Boot and make it easier to port it to custom
3921 Initial Stack, Global Data:
3922 ---------------------------
3924 The implementation of U-Boot is complicated by the fact that U-Boot
3925 starts running out of ROM (flash memory), usually without access to
3926 system RAM (because the memory controller is not initialized yet).
3927 This means that we don't have writable Data or BSS segments, and BSS
3928 is not initialized as zero. To be able to get a C environment working
3929 at all, we have to allocate at least a minimal stack. Implementation
3930 options for this are defined and restricted by the CPU used: Some CPU
3931 models provide on-chip memory (like the IMMR area on MPC8xx and
3932 MPC826x processors), on others (parts of) the data cache can be
3933 locked as (mis-) used as memory, etc.
3935 Chris Hallinan posted a good summary of these issues to the
3936 U-Boot mailing list:
3938 Subject: RE: [U-Boot-Users] RE: More On Memory Bank x (nothingness)?
3939 From: "Chris Hallinan" <clh@net1plus.com>
3940 Date: Mon, 10 Feb 2003 16:43:46 -0500 (22:43 MET)
3943 Correct me if I'm wrong, folks, but the way I understand it
3944 is this: Using DCACHE as initial RAM for Stack, etc, does not
3945 require any physical RAM backing up the cache. The cleverness
3946 is that the cache is being used as a temporary supply of
3947 necessary storage before the SDRAM controller is setup. It's
3948 beyond the scope of this list to explain the details, but you
3949 can see how this works by studying the cache architecture and
3950 operation in the architecture and processor-specific manuals.
3952 OCM is On Chip Memory, which I believe the 405GP has 4K. It
3953 is another option for the system designer to use as an
3954 initial stack/RAM area prior to SDRAM being available. Either
3955 option should work for you. Using CS 4 should be fine if your
3956 board designers haven't used it for something that would
3957 cause you grief during the initial boot! It is frequently not
3960 CONFIG_SYS_INIT_RAM_ADDR should be somewhere that won't interfere
3961 with your processor/board/system design. The default value
3962 you will find in any recent u-boot distribution in
3963 walnut.h should work for you. I'd set it to a value larger
3964 than your SDRAM module. If you have a 64MB SDRAM module, set
3965 it above 400_0000. Just make sure your board has no resources
3966 that are supposed to respond to that address! That code in
3967 start.S has been around a while and should work as is when
3968 you get the config right.
3973 It is essential to remember this, since it has some impact on the C
3974 code for the initialization procedures:
3976 * Initialized global data (data segment) is read-only. Do not attempt
3979 * Do not use any uninitialized global data (or implicitely initialized
3980 as zero data - BSS segment) at all - this is undefined, initiali-
3981 zation is performed later (when relocating to RAM).
3983 * Stack space is very limited. Avoid big data buffers or things like
3986 Having only the stack as writable memory limits means we cannot use
3987 normal global data to share information beween the code. But it
3988 turned out that the implementation of U-Boot can be greatly
3989 simplified by making a global data structure (gd_t) available to all
3990 functions. We could pass a pointer to this data as argument to _all_
3991 functions, but this would bloat the code. Instead we use a feature of
3992 the GCC compiler (Global Register Variables) to share the data: we
3993 place a pointer (gd) to the global data into a register which we
3994 reserve for this purpose.
3996 When choosing a register for such a purpose we are restricted by the
3997 relevant (E)ABI specifications for the current architecture, and by
3998 GCC's implementation.
4000 For PowerPC, the following registers have specific use:
4002 R2: reserved for system use
4003 R3-R4: parameter passing and return values
4004 R5-R10: parameter passing
4005 R13: small data area pointer
4009 (U-Boot also uses R12 as internal GOT pointer. r12
4010 is a volatile register so r12 needs to be reset when
4011 going back and forth between asm and C)
4013 ==> U-Boot will use R2 to hold a pointer to the global data
4015 Note: on PPC, we could use a static initializer (since the
4016 address of the global data structure is known at compile time),
4017 but it turned out that reserving a register results in somewhat
4018 smaller code - although the code savings are not that big (on
4019 average for all boards 752 bytes for the whole U-Boot image,
4020 624 text + 127 data).
4022 On Blackfin, the normal C ABI (except for P3) is followed as documented here:
4023 http://docs.blackfin.uclinux.org/doku.php?id=application_binary_interface
4025 ==> U-Boot will use P3 to hold a pointer to the global data
4027 On ARM, the following registers are used:
4029 R0: function argument word/integer result
4030 R1-R3: function argument word
4032 R10: stack limit (used only if stack checking if enabled)
4033 R11: argument (frame) pointer
4034 R12: temporary workspace
4037 R15: program counter
4039 ==> U-Boot will use R8 to hold a pointer to the global data
4041 On Nios II, the ABI is documented here:
4042 http://www.altera.com/literature/hb/nios2/n2cpu_nii51016.pdf
4044 ==> U-Boot will use gp to hold a pointer to the global data
4046 Note: on Nios II, we give "-G0" option to gcc and don't use gp
4047 to access small data sections, so gp is free.
4049 NOTE: DECLARE_GLOBAL_DATA_PTR must be used with file-global scope,
4050 or current versions of GCC may "optimize" the code too much.
4055 U-Boot runs in system state and uses physical addresses, i.e. the
4056 MMU is not used either for address mapping nor for memory protection.
4058 The available memory is mapped to fixed addresses using the memory
4059 controller. In this process, a contiguous block is formed for each
4060 memory type (Flash, SDRAM, SRAM), even when it consists of several
4061 physical memory banks.
4063 U-Boot is installed in the first 128 kB of the first Flash bank (on
4064 TQM8xxL modules this is the range 0x40000000 ... 0x4001FFFF). After
4065 booting and sizing and initializing DRAM, the code relocates itself
4066 to the upper end of DRAM. Immediately below the U-Boot code some
4067 memory is reserved for use by malloc() [see CONFIG_SYS_MALLOC_LEN
4068 configuration setting]. Below that, a structure with global Board
4069 Info data is placed, followed by the stack (growing downward).
4071 Additionally, some exception handler code is copied to the low 8 kB
4072 of DRAM (0x00000000 ... 0x00001FFF).
4074 So a typical memory configuration with 16 MB of DRAM could look like
4077 0x0000 0000 Exception Vector code
4080 0x0000 2000 Free for Application Use
4086 0x00FB FF20 Monitor Stack (Growing downward)
4087 0x00FB FFAC Board Info Data and permanent copy of global data
4088 0x00FC 0000 Malloc Arena
4091 0x00FE 0000 RAM Copy of Monitor Code
4092 ... eventually: LCD or video framebuffer
4093 ... eventually: pRAM (Protected RAM - unchanged by reset)
4094 0x00FF FFFF [End of RAM]
4097 System Initialization:
4098 ----------------------
4100 In the reset configuration, U-Boot starts at the reset entry point
4101 (on most PowerPC systems at address 0x00000100). Because of the reset
4102 configuration for CS0# this is a mirror of the onboard Flash memory.
4103 To be able to re-map memory U-Boot then jumps to its link address.
4104 To be able to implement the initialization code in C, a (small!)
4105 initial stack is set up in the internal Dual Ported RAM (in case CPUs
4106 which provide such a feature like MPC8xx or MPC8260), or in a locked
4107 part of the data cache. After that, U-Boot initializes the CPU core,
4108 the caches and the SIU.
4110 Next, all (potentially) available memory banks are mapped using a
4111 preliminary mapping. For example, we put them on 512 MB boundaries
4112 (multiples of 0x20000000: SDRAM on 0x00000000 and 0x20000000, Flash
4113 on 0x40000000 and 0x60000000, SRAM on 0x80000000). Then UPM A is
4114 programmed for SDRAM access. Using the temporary configuration, a
4115 simple memory test is run that determines the size of the SDRAM
4118 When there is more than one SDRAM bank, and the banks are of
4119 different size, the largest is mapped first. For equal size, the first
4120 bank (CS2#) is mapped first. The first mapping is always for address
4121 0x00000000, with any additional banks following immediately to create
4122 contiguous memory starting from 0.
4124 Then, the monitor installs itself at the upper end of the SDRAM area
4125 and allocates memory for use by malloc() and for the global Board
4126 Info data; also, the exception vector code is copied to the low RAM
4127 pages, and the final stack is set up.
4129 Only after this relocation will you have a "normal" C environment;
4130 until that you are restricted in several ways, mostly because you are
4131 running from ROM, and because the code will have to be relocated to a
4135 U-Boot Porting Guide:
4136 ----------------------
4138 [Based on messages by Jerry Van Baren in the U-Boot-Users mailing
4142 int main(int argc, char *argv[])
4144 sighandler_t no_more_time;
4146 signal(SIGALRM, no_more_time);
4147 alarm(PROJECT_DEADLINE - toSec (3 * WEEK));
4149 if (available_money > available_manpower) {
4150 Pay consultant to port U-Boot;
4154 Download latest U-Boot source;
4156 Subscribe to u-boot mailing list;
4159 email("Hi, I am new to U-Boot, how do I get started?");
4162 Read the README file in the top level directory;
4163 Read http://www.denx.de/twiki/bin/view/DULG/Manual;
4164 Read applicable doc/*.README;
4165 Read the source, Luke;
4166 /* find . -name "*.[chS]" | xargs grep -i <keyword> */
4169 if (available_money > toLocalCurrency ($2500))
4172 Add a lot of aggravation and time;
4174 if (a similar board exists) { /* hopefully... */
4175 cp -a board/<similar> board/<myboard>
4176 cp include/configs/<similar>.h include/configs/<myboard>.h
4178 Create your own board support subdirectory;
4179 Create your own board include/configs/<myboard>.h file;
4181 Edit new board/<myboard> files
4182 Edit new include/configs/<myboard>.h
4187 Add / modify source code;
4191 email("Hi, I am having problems...");
4193 Send patch file to the U-Boot email list;
4194 if (reasonable critiques)
4195 Incorporate improvements from email list code review;
4197 Defend code as written;
4203 void no_more_time (int sig)
4212 All contributions to U-Boot should conform to the Linux kernel
4213 coding style; see the file "Documentation/CodingStyle" and the script
4214 "scripts/Lindent" in your Linux kernel source directory. In sources
4215 originating from U-Boot a style corresponding to "Lindent -pcs" (adding
4216 spaces before parameters to function calls) is actually used.
4218 Source files originating from a different project (for example the
4219 MTD subsystem) are generally exempt from these guidelines and are not
4220 reformated to ease subsequent migration to newer versions of those
4223 Please note that U-Boot is implemented in C (and to some small parts in
4224 Assembler); no C++ is used, so please do not use C++ style comments (//)
4227 Please also stick to the following formatting rules:
4228 - remove any trailing white space
4229 - use TAB characters for indentation, not spaces
4230 - make sure NOT to use DOS '\r\n' line feeds
4231 - do not add more than 2 empty lines to source files
4232 - do not add trailing empty lines to source files
4234 Submissions which do not conform to the standards may be returned
4235 with a request to reformat the changes.
4241 Since the number of patches for U-Boot is growing, we need to
4242 establish some rules. Submissions which do not conform to these rules
4243 may be rejected, even when they contain important and valuable stuff.
4245 Please see http://www.denx.de/wiki/U-Boot/Patches for details.
4247 Patches shall be sent to the u-boot mailing list <u-boot@lists.denx.de>;
4248 see http://lists.denx.de/mailman/listinfo/u-boot
4250 When you send a patch, please include the following information with
4253 * For bug fixes: a description of the bug and how your patch fixes
4254 this bug. Please try to include a way of demonstrating that the
4255 patch actually fixes something.
4257 * For new features: a description of the feature and your
4260 * A CHANGELOG entry as plaintext (separate from the patch)
4262 * For major contributions, your entry to the CREDITS file
4264 * When you add support for a new board, don't forget to add this
4265 board to the MAKEALL script, too.
4267 * If your patch adds new configuration options, don't forget to
4268 document these in the README file.
4270 * The patch itself. If you are using git (which is *strongly*
4271 recommended) you can easily generate the patch using the
4272 "git-format-patch". If you then use "git-send-email" to send it to
4273 the U-Boot mailing list, you will avoid most of the common problems
4274 with some other mail clients.
4276 If you cannot use git, use "diff -purN OLD NEW". If your version of
4277 diff does not support these options, then get the latest version of
4280 The current directory when running this command shall be the parent
4281 directory of the U-Boot source tree (i. e. please make sure that
4282 your patch includes sufficient directory information for the
4285 We prefer patches as plain text. MIME attachments are discouraged,
4286 and compressed attachments must not be used.
4288 * If one logical set of modifications affects or creates several
4289 files, all these changes shall be submitted in a SINGLE patch file.
4291 * Changesets that contain different, unrelated modifications shall be
4292 submitted as SEPARATE patches, one patch per changeset.
4297 * Before sending the patch, run the MAKEALL script on your patched
4298 source tree and make sure that no errors or warnings are reported
4299 for any of the boards.
4301 * Keep your modifications to the necessary minimum: A patch
4302 containing several unrelated changes or arbitrary reformats will be
4303 returned with a request to re-formatting / split it.
4305 * If you modify existing code, make sure that your new code does not
4306 add to the memory footprint of the code ;-) Small is beautiful!
4307 When adding new features, these should compile conditionally only
4308 (using #ifdef), and the resulting code with the new feature
4309 disabled must not need more memory than the old code without your
4312 * Remember that there is a size limit of 100 kB per message on the
4313 u-boot mailing list. Bigger patches will be moderated. If they are
4314 reasonable and not too big, they will be acknowledged. But patches
4315 bigger than the size limit should be avoided.
projects / platform / kernel / u-boot.git / blob