* Patch by Jian Zhang, 3 Feb 2004:
[kernel/u-boot.git] / CHANGELOG
1 ======================================================================
2 Changes since U-Boot 1.0.1:
3 ======================================================================
4
5 * Patch by Jian Zhang, 3 Feb 2004:
6   - Changed the incorrect FAT12BUFSIZE
7   - data_begin in fsdata can be negative. Changed it to be short.
8
9 * Patches by Stephan Linz, 30 Jan 2004:
10   1: - board/altera/common/flash.c:flash_erase():
11        o allow interrupts befor get_timer() call
12        o check-up each erased sector and avoid unexpected timeouts
13      - board/altera/dk1c20/dk1s10.c:board_early_init_f():
14        o enclose sevenseg_set() in cpp condition
15      - remove the ASMI configuration for DK1S10_standard_32 (never present)
16      - fix some typed in mistakes in the NIOS documentation
17   2: - split DK1C20 configuration into several header files:
18        o two new files for each NIOS CPU description
19        o U-Boot related part is remaining in DK1C20.h
20   3: - split DK1S10 configuration into several header files:
21        o two new files for each NIOS CPU description
22        o U-Boot related part is remaining in DK1S10.h
23   4: - Add support for the Microtronix Linux Development Kit
24        NIOS CPU configuration at the Altera Nios Development Kit,
25        Stratix Edition (DK-1S10)
26   5: - Add documentation for the Altera Nios Development Kit,
27        Stratix Edition (DK-1S10)
28   6: - Add support for the Nios Serial Peripharel Interface (SPI)
29        (master only)
30   7: - Add support for the common U-Boot SPI framework at
31        RTC driver DS1306
32
33 * Patch by Rahul Shanbhag, 28 Jan 2004:
34   Fix flash protection/locking handling for OMAP1610 innovator board.
35
36 * Patch by Rolf Peukert, 28 Jan 2004:
37   fix flash write problems on CSB226 board (write with 32 bit bus width)
38
39 * Patches by Mark Jonas, 16 Jan 2004:
40   - fix rounding error when calculating baudrates for MPC5200 PSCs
41   - make sure CFG_RAMBOOT and CFG_LOWBOOT are not enabled at the same
42     time which is not supported
43
44 * Patch by Yuli Barcohen, 26 Jan 2004:
45   Allow bzip2 compression for small memory footprint boards
46
47 * Patch by Brad Kemp, 21 Jan 2004:
48   Add support for CFI flash driver for both the Intel and the AMD
49   command sets.
50
51 * Patch by Travis Sawyer, 20 Jan 2004:
52   Fix pci bridge auto enumeration of sibling p2p bridges.
53
54 * Patch by Tolunay Orkun, 12 Jan 2004:
55   Add some delays as needed for Intel LXT971A PHY support
56
57 * Patches by Stephan Linz, 09 Jan 2004:
58   - avoid warning: unused variable `piop' in board/altera/common/sevenseg.c
59   - make DK1C20 board configuration related to ASMI conform to
60     documentation
61
62 * Patch by Anders Larsen, 09 Jan 2004:
63
64   ARM memory layout fixes: the abort-stack is now set up in the
65   correct RAM area, and the BSS is zeroed out as it should be.
66
67   Furthermore, the magic variables 'armboot_end' and 'armboot_end_data'
68   of the linker scripts are replaced by '__bss_start' and '_end',
69   resp., which is a further step to eliminate unnecessary differences
70   between the implementation of the CPU architectures.
71
72 * Patch by liang a lei, 9 Jan 2004:
73   Fix Intel 28F128J3 ID in include/flash.h
74
75 * Patch by Masami Komiya, 09 Jan 2004:
76   add support for TB0229 board (NEC VR4131 MIPS processor)
77
78 * Patch by Leon Kukovec, 12 Dec 2003:
79   changed extern __inline__ into static __inline__ in
80   include/linux/byteorder/swab.h
81
82 * Patch by Travis Sawyer, 30 Dec 2003:
83   Add support for IBM PPC440GX. Multiple EMAC Ethernet devices,
84   select MDI port based on enabled EMAC device.
85   Add support for XES Inc <http://www.xes-inc.com> XPedite1000 440GX
86   base PrPMC board.
87
88 * Patch by Wolter Kamphuis, 15 Dec 2003:
89   made CONFIG_SILENT_CONSOLE usable on all architectures
90
91 * Disable date command on TQM866M - there is no RTC on MPC866
92
93 * Fix variable CPU clock for MPC859/866 systems for low CPU clocks
94
95 * Implement adaptive SDRAM timing configuration based on actual CPU
96   clock frequency for INCA-IP; fix problem with board hanging when
97   switching from 150MHz to 100MHz
98
99 * Add PCMCIA CS support for BMS2003 board
100
101 * Add variable CPU clock for MPC859/866 systems (so far only TQM866M):
102   see doc/README.MPC866 for details;
103   implement workaround for "SIU4" and "SIU9" silicon bugs on MPC866;
104   calculate CPU clock frequency from PLL register values.
105
106 * Add support for 128 MB RAM on TQM8xxL/M modules
107
108 * Fix PS/2 keyboard problem caused by statically initialized variable
109   pointing to a location in flash
110
111 * Fix INCA-IP clock calculation: 400/3 = 133.3 MHz, not 130.
112
113 * The PS/2 mux on the BMS2003 board needs 450 ms after power on
114   before we can access it; add delay in case we are faster (with no
115   CF card inserted)
116
117 * Cleanup of some init functions
118
119 * Make sure SCC Ethernet is always stopped by the time we boot Linux
120   to avoid Linux crashes by early packets coming in.
121
122 * Accelerate flash accesses on LWMON board by using buffered writes
123
124 * Fix typo in Makefile;
125   fix problem with PARTNUM detection
126
127 * Patch by Reinhard Meyer, 09 Jan 2004:
128   - add RTC support for MPC5200 based boards (requires RTC_XTAL)
129
130 * Add support for IDE LED on BMS2003 board
131   (exclusive with status LED!)
132
133 * Add support for PS/2 keyboard (used with PS/2 multiplexor on
134   BMS2003 board)
135
136 * Patches by Reinhard Meyer, 4 Jan 2004 + 7 Jan 2004:
137   Add common files for "emk" boards
138
139 * Add a common get_ram_size() function and modify the the
140   board-specific files to invoke that common implementation.
141
142 ======================================================================
143 Changes for U-Boot 1.0.1:
144 ======================================================================
145
146 * Set default clock for INCA-IP to 150 MHz
147
148 * Make BMS2003 use a separate config file to avoid #ifdef mess;
149   add I2C support; add support for DS1337 RTC
150
151 * Add CompactFlash support  for BMS2003 board
152
153 * Add support for status LED on BMS2003 board
154
155 * Patch by Scott McNutt, 02 Jan 2004:
156   Add support for the Nios Active Serial Memory Interface (ASMI)
157   on Cyclone devices
158
159 * Patch by Andrea Marson, 16 Dec 2003:
160   Add support for the PPChameleon ME and HI modules
161
162 * Patch by Yuli Barcohen, 22 Dec 2003:
163   Add support for Motorola DUET ADS board (MPC87x/88x)
164
165 * Patch by Robert Schwebel, 15 Dec 2003:
166   add support for cramfs (uses JFFS2 command interface)
167
168 * Patches by Stephan Linz, 11 Dec 2003:
169   - more documentation for NIOS port
170   - new struct nios_pio_t, struct nios_spi_t
171   - Reconfiguration for NIOS Development Kit DK1C20:
172     o move board related code from board/dk1c20
173       to board/altera/dk1c20
174     o create a new common source path board/altera/common
175       and move generic flash access stuff into it
176     o change/expand configuration file DK1C20.h
177   - Add support for NIOS Development Kit DK1S10
178   - Add status LED support for NIOS systems
179   - Add dual 7-segment LED support for Altera NIOS DevKits
180
181 * Patch by Ronen Shitrit, 10 Dec 2003:
182   Add support for the Marvell DB64360 / DB64460 development boards
183
184 * Patch by Detlev Zundel, 10 Dec 2003:
185   fix dependency problem in examples/Makefile
186
187 * Patch by Denis Peter, 8 Dec 2003
188   - add support for the PATI board (MPC555)
189   - add SPI support for the MPC5xx
190
191 * Patch by Anders Larsen, 08 Dec 2003:
192   add configuration options CONFIG_SERIAL_TAG and CONFIG_REVISION_TAG
193   to pass ATAG_SERIAL and ATAG_REVISION, resp., to the ARM target;
194   cleanup some redundand #defines
195
196 * Patch by André Schwarz, 8 Dec 2003:
197   fixes for Davicom DM9102A Ethernet Chip (#define CONFIG_TULIP_FIX_DAVICOM):
198   - TX and RX deskriptors must be quad-word aligned
199   - does not work with only one TX deskriptor
200   - standard reset method does not work
201
202 * Patch by Masami Komiya, 08 Dec 2003:
203   add RTL8139 ethernet driver
204
205 * Patches by Ed Okerson, 07 Dec 2003:
206   - fix ethernet for the AU1x00 processors in little-endian mode.
207   - extend memsetup.S for the AU1x00 processors in BE and LE modes
208
209 * Minor code cleanup (coding style)
210
211 * Patch by Reinhard Meyer, 30 Dec 2003:
212   - cpu/mpc5xxx/fec.c: added CONFIG_PHY_ADDR, added CONFIG_PHY_TYPE,
213   - added CONFIG_PHY_ADDR to include/configs/IceCube.h,
214   - turned debug print of PHY registers into a function (called in two places)
215   - added support for EMK MPC5200 based modules
216
217 * Fix MPC8xx PLPRCR_MFD_SHIFT typo
218
219 * Add support for TQM866M modules
220
221 * Fixes for TQM855M with 4 MB flash (Am29DL163 = _no_ mirror bit flash)
222
223 * Fix a few compiler warnings
224
225 * Patch by Reinhard Meyer, 28 Dec 2003:
226   Add initial support for TOP5200 board
227
228 * Make CPU clock on ICA-IP board controllable by a "cpuclk"
229   environment variable which can set to "100", "133", or "150". The
230   CPU clock will be configured accordingly upon next reboot. Other
231   values are ignored. In case of an invalid or undefined "cpuclk"
232   value, the compile-time default CPU clock speed will be used.
233
234 * Enable Quad-UART on BMS2003 board (initialize the PCMCIA memory
235   window that is used to access the UART registers by the Linux driver)
236
237 * Patch by Reinhard Meyer, 20 Dec 2003:
238   Fix clock calculation for the MPC5200 for higher clock frequencies
239   (above 2**32 / 10 = 429.5 MHz).
240
241 * Fix CONFIG_PLL_PCI_TO_MEM_MULTIPLIER divider error in SP8240 configuration
242
243 * Fix IceCube CLKIN configuration (it's 33.000000MHz)
244
245 * Add new configuration for IceCube board with DDR memory
246
247 * Update TRAB memory configurations
248
249 * Add JFFS2 support for INCA-IP board
250
251 * Patch by Bill Hargen, 09 Dec 2003:
252   - BUBINGA405EP: changed flash driver to protect top sector containing
253     first instruction.
254   - BUBINGA405EP: configured "eeprom" command to access boot config EEPROM.
255   - BUBINGA405EP: fixed PLL init (init chip selects before FPGA/NVRAM access).
256   - 405EP: fixed SPD-based SDRAM init (only use banks 0 and 1).
257   - 405EP: added/fixed support for "reginfo" command.
258   - 4xx: removed spurious MII error messages on "mii info" command.
259
260 * Patch by Bernhard Kuhn, 28 Nov 2003:
261   add support for Coldfire CPU
262   add support for Motorola M5272C3 and M5282EVB boards
263
264 * Patch by Pierre Aubert, 24 Nov 2003:
265   - add a return value for the fpga command
266   - add ide_preinit() function called in ide_init if CONFIG_IDE_PREINIT
267     is defined. If ide_preinit fails, ide_init is aborted.
268   - fix an endianess problem in fat.h
269
270 * Patch by Wolter Kamphuis, 05 Dec 2003:
271   Add support for SNMC's QS850/QS823/QS860T boards
272
273 * Patch by Yuli Barcohen, 3 Dec 2003:
274   "revive" U-Boot support for old Motorola MPC860ADS board
275
276 * Patch by Cam(ilo?), 03 Dec 2003:
277   make examples build even with broken Montavista objcopy
278
279 * Patch by Pavel Bartusek, 27 Nov 2003:
280   fix conversion problem with "bootretry" evironment variable
281
282 * Patch by Andre Schwarz, 24 Nov 2003:
283   add support for mvblue (mvBlueLYNX and mvBlueBOX) boards
284
285 * Patch by Pavel Bartusek, 21 Nov 2003:
286   set ZMII bridge speed on 440
287
288 * Patch by Anders Larsen, 17 Nov 2003:
289   Fix mismatched #ifdef / #endif in include/asm-arm/arch-pxa/hardware.h
290
291 * Patches by David Müller, 14 Nov 2003:
292   - board/mpl/common/common_util.c
293     * implement support for BZIP2 compressed images
294     * various cleanups (printf -> puts, ...)
295   - board/mpl/common/flash.c
296     * report correct errors to upper layers
297     * check the erase fail and VPP low bits in status reg
298   - board/mpl/vcma9/cmd_vcma9.c
299   - board/mpl/vcma9/flash.c
300     * various cleanups (printf -> puts, ...)
301   - common/cmd_usb.c
302     * fix typo in comment
303   - cpu/arm920t/usb_ohci.c
304     * support for S3C2410 is missing in #if line
305   - drivers/cs8900.c
306     * reinit some registers in case of error (cable missing, ...)
307   - fs/fat/fat.c
308     * support for USB/MMC devices is missing in #if line
309   - include/configs/MIP405.h
310   - include/configs/PIP405.h
311     * enable BZIP2 support
312     * enlarge malloc space to 1MiB because of BZIP2 support
313   - include/configs/VCMA9.h
314     * enable BZIP2 support
315     * enlarge malloc space to 1MiB because of BZIP2 support
316     * enable USB support
317   - lib_arm/armlinux.c
318     * change calling convention of ARM Linux kernel as
319       described on http://www.arm.linux.org.uk/developer/booting.php
320
321 * Patch by Thomas Lange, 14 Nov 2003:
322   Split dbau1x00 into dbau1000, dbau1100 and dbau1500 configs to
323   support all these AMD boards.
324
325 * Patch by Thomas Lange, 14 Nov 2003:
326   Workaround for mips au1x00 physical memory accesses (the au1x00
327   uses a 36 bit bus internally and cannot access physical memory
328   directly. Use the uncached SDRAM address instead of the physical
329   one.)
330
331 * Patch by Xue Ligong (Joe), 13 Nov 2003:
332   add Realtek 8019 ethernet driver
333
334 * Patch by Yuli Barcohen, 13 Nov 2003:
335   MPC826xADS/PQ2FADS  cleanup
336
337 * Patch by Anders Larsen, 12 Nov 2003:
338   Update README to mark the PORTIO commands non-standard
339
340 * Patch by Nicolas Lacressonnière, 12 Nov 2003:
341   update for for Atmel AT91RM9200DK development kit:
342   - support for environment variables in DataFlash
343   - Atmel DataFlash AT45DB1282 support
344
345 * Patch by Jeff Carr, 11 Nov 2003:
346   add support for new version of 8270 processors
347
348 * Patches by George G. Davis, 05 Nov 2003:
349   - only pass the ARM linux initrd tag to the kernel when an initrd
350     is actually present
351   - update omap1510inn configuration file
352
353 * Patches by Stephan Linz, 3 Nov 2003:
354   - more endianess fixes for LAN91C111 driver
355   - CFG_HZ configuration patch for NIOS Cyclone board
356
357 * Patch by Stephan Linz, 28 Oct 2003:
358   fix PHY_INT_REG vs. PHY_MASK_REG bug in drivers/smc91111.c
359
360 * Patch by Steven Scholz, 20 Oct 2003:
361   - make "mii info <addr>" show infor for PHY at "addr" only
362   - Endian fix for miiphy_info()
363
364 * Patch by Gleb Natapov, 19 Sep 2003:
365   Move most of the timer interrupt related PPC code to ppc_lib/interrupts.c
366
367 * Patch by Anders Larsen, 17 Sep 2003:
368   Bring ARM memory layout in sync with the documentation:
369   stack and malloc-heap are now located _below_ the U-Boot code
370
371 * Accelerate booting on TRAB board: read and check  autoupdate  image
372   headers first instead of always reading the whole images.
373
374 * Fix type in MPC5XXX code (pointed out by Victor Wren)
375
376 * Enabled password check on RMU board
377
378 * Fix configuration problem with IceCube in LOWBOOT configuration:
379   envrionment got embedded, corrupting the image layout.
380
381 * Fix NEC display names (it's 6440 [for 640x480], not 6640).
382
383 * Added BMS2003 board
384   add support for NEC NL6448BC33-54. 10.4", 640x480 TFT display
385
386 * Fix flash driver for TRAB board (must use Unlock Bypass Reset
387   command to exit Unlock Bypass Mode); adjust timings for flash, SRAM
388   and CPLD
389
390 * Use "-fPIC" instead of "-mrelocatable" to prevent problems with
391   recent tools
392
393 * Add checksum verification to 'imls' command
394
395 * Add bd_info fields needed for 4xx Linux I2C driver
396
397 * Patch by Martin Krause, 4 Nov. 2003:
398   Fix error in cmd_vfd.c (TRAB board: "vfd /1" shows now only one Bitmap)
399
400 * Print used network interface when CONFIG_NET_MULTI is set
401
402 * Patch by Bernhard Kuhn, 28 Oct 2003:
403   Add low boot support for MPC5200
404
405 * Fix problem with dual PCMCIA support (NSCU)
406
407 * Fix MPC5200 I2C initialization function
408
409 ======================================================================
410 Changes for U-Boot 1.0.0:
411 ======================================================================
412
413 * Fix parameter passing to standalone images with bootm command
414
415 * Patch by Kyle Harris, 30 Oct 2003:
416   Fix build errors for ixdp425 board
417
418 * Patch by David M. Horn, 29 Oct 2003:
419   Fixes to build under CYGWIN
420
421 * Get IceCube MGT5100 working (again)
422
423 * Fix problems in memory test on some boards (which was not
424   non-destructive as intended)
425
426 * Patch by Gary Jennejohn, 28 Oct 2003:
427   Change fs/fat/fat.c to put I/O buffers in BSS instead on the stack
428   to prevent stack overflow on ARM systems
429
430 * Patch by Stephan Linz, 28 Oct 2003:
431   fix init sequence error for NIOS port
432
433 * Allow lowercase spelling for IceCube_5200; support MPC5200LITE name
434
435 * Add CONFIG_VERSION_VARIABLE to TRAB configuration
436
437 * Patch by Xiao Xianghua, 23 Oct 2003:
438   small patch for mpc85xx
439
440 * Fix small problem in MPC5200 I2C driver
441
442 * Fix FCC3 support on ATC board
443
444 * Correct header printing for multi-image files in do_bootm()
445
446 * Make CONFIG_SILENT_CONSOLE work with CONFIG_AUTOBOOT_KEYED
447
448 * Fix PCI problems on PPChameleon board
449
450 * Patch by Steven Scholz, 18 Oct 2003:
451   Fix AT91RM9200 ethernet driver
452
453 * Patch by Nye Liu, 17 Oct 2003:
454   Fix typo in include/mpc8xx.h
455
456 * Patch by Richard Woodruff, 16 Oct 03:
457   Fixes for cpu/arm925/interrupt.c
458   - Initialize timestamp & lastdec vars.
459   - fix timestamp overflows.
460   - fix lastdec overflow.
461   - smarter normalization to allow udelay() below 1ms to work.
462
463 * Patch by Scott McNutt, 16 Oct
464   add networking support for the Altera Nios Development Kit,
465   Cyclone Edition (DK-1C20)
466
467 * Patch by Jon Diekema, 14 Oct 2003:
468   add hint about doc/README.silent to README file
469
470 * Add CompactFlash support for NSCU
471
472 * Fix PCI problems on PPChameleonEVB
473
474 * TRAB auto-update: Base decision if we have to strip the image
475   header on image type as encoded in the header
476   (include image type patch by Martin Krause, 17 Oct 2003)
477
478 * Patches by Xianghua Xiao, 15 Oct 2003:
479
480   - Added Motorola CPU 8540/8560 support (cpu/85xx)
481   - Added Motorola MPC8540ADS board support (board/mpc8540ads)
482   - Added Motorola MPC8560ADS board support (board/mpc8560ads)
483
484 * Fix flash timings on TRAB board
485
486 * Make sure HUSH is initialized for running auto-update scripts
487
488 * Make 5200 reset command _really_ reset the board, without running
489   any other code after it
490
491 * Fix errors with flash erase when range spans  across banks
492   that are mapped in reverse order
493
494 * Fix flash mapping and display on P3G4 board
495
496 * Patch by Kyle Harris, 15 Jul 2003:
497   - add support for Intel IXP425 CPU
498   - add support for IXDP425 eval board
499
500 * Added config option CONFIG_SILENT_CONSOLE.  See doc/README.silent
501   for more information
502
503 * Patch by Steven Scholz, 10 Oct 2003
504   - Add support for Altera FPGA ACEX1K
505
506 * Patches by Thomas Lange, 09 Oct 2003:
507   - fix cmd_ide.c for non ppc boards (read/write functions did not
508     add ATA base address)
509   - fix for shannon board
510   - #ifdef CONFIG_IDE_8xx_DIRECT some otherwise unused code
511   - Endian swap ATA identity for all big endian CPUs, not just PPC
512   - MIPS only: New option CONFIG_MEMSIZE_IN_BYTES for passing memsize
513     args to linux
514   - add support for dbau1x00 board (MIPS32)
515
516 * Patch by Sangmoon Kim, 07 Oct 2003:
517   add support for debris board
518
519 * Patch by Martin Krause, 09 Oct 2003:
520   Fixes for TRAB board
521   - /board/trab/rs485.c: correct baudrate
522   - /board/trab/cmd_trab.c: bug fix for problem with timer overflow in
523     udelay(); fix some timing problems with adc controller
524   - /board/trab/trab_fkt.c: add new commands: gain, eeprom and power;
525     modify commands: touch and buzzer
526
527 * Disable CONFIG_SUPPORT_VFAT when used with CONFIG_AUTO_UPDATE
528   (quick & dirty workaround for rogue pointer problem in get_vfatname());
529   Use direct function calls for auto_update instead of hush commands
530
531 * Patch by Scott McNutt, 04 Oct 2003:
532   - add support for Altera Nios-32 CPU
533   - add support for Nios Cyclone Development Kit (DK-1C20)
534
535 * Patch by Steven Scholz, 29 Sep 2003:
536   - A second parameter for bootm overwrites the load address for
537     "Standalone Application" images.
538   - bootm sets environment variable "filesize" to the resulting
539     (uncompressed) data length for "Standalone Application" images
540     when autostart is set to "no". Now you can do something like
541         if bootm $fpgadata $some_free_ram ; then
542                 fpga load 0 $some_free_ram $filesize
543         fi
544
545 * Patch by Denis Peter, 25 Sept 2003:
546   add support for the MIP405 Rev. C board
547
548 * Patch by Yuli Barcohen, 25 Sep 2003:
549   add support for Zephyr Engineering ZPC.1900 board
550
551 * Patch by Anders Larsen, 23 Sep 2003:
552   add CMD_PORTIO to CFG_CMD_NONSTD (commands in question are only
553   implemented for the x86 architecture)
554
555 * Patch by Sangmoon Kim, 23 Sep 2003:
556   fix pll_pci_to_mem_multiplier table for MPC8245
557
558 * Patch by Anders Larsen, 22 Sep 2003:
559   enable timed autoboot on PXA
560
561 * Patch by David Müller, 22 Sep 2003:
562   - add $(CFLAGS) to "-print-libgcc-filename" so compiler driver
563     returns correct libgcc file path
564   - "latency" reduction of busy-loop waiting to improve "U-Boot" boot
565     time on s3c24x0 systems
566
567 * Patch by Jon Diekema, 19 Sep 2003:
568   - Add CFG_FAULT_ECHO_LINK_DOWN option to echo the inverted Ethernet
569     link state to the fault LED.
570   - In NetLoop, make the Fault LED reflect the link status.  The link
571     status gets updated on entry, and on timeouts.
572
573 * Patch by Anders Larsen, 18 Sep 2003:
574   allow mkimage to build and run on Cygwin-hosted systems
575
576 * Patch by Frank Müller, 18 Sep 2003:
577   use bi_intfreq instead of bi_busfreq to compute fec_mii_speed in
578   cpu/mpc8xx/fec.c
579
580 * Patch by Pantelis Antoniou, 16 Sep 2003:
581   add tool to compute fileds in the PLPRCR register for MPC86x
582
583 * Use IH_TYPE_FILESYSTEM for TRAB "disk" images.
584
585 * Fix build problems under FreeBSD
586
587 * Add generic filesystem image type
588
589 * Make fatload set filesize environment variable
590
591 * enable basic / medium / high-end configurations for PPChameleonEVB
592   board; fix NAND code
593
594 * enable TFTP client code to specify to the server the desired
595   timeout value (see RFC-2349)
596
597 * Improve SDRAM setup for TRAB board
598
599 * Suppress all output with splashscreen configured only if "splashimage"
600   is set
601
602 * Fix problems with I2C support for mpc5200
603
604 * Adapt TRAB configuration and auto_update to new memory layout
605
606 * Add configuration for wtk board
607
608 * Add support for the Sharp LQ065T9DR51U LCD display
609
610 * Patch by Rune Torgersen, 17 Sep 2003:
611   - Fixes for MPC8266 default config
612   - Allow eth_loopback_test() on 8260 to use a subset of the FCC's
613
614 * Patches by Jon Diekema, 17 Sep 2003:
615   - update README (SHOW_BOOT_PROGRESS values for cmd_nand.c and
616     env_common.c)
617   - sbc8260 tweaks
618   - adjust "help" output
619
620 * Patches by Anders Larsen, 17 Sep 2003:
621   - fix spelling errors
622   - set GD_FLG_DEVINIT flag only after device function pointers
623     are valid
624   - Allow CFG_ALT_MEMTEST on systems where address zero isn't
625     writeable
626   - enable 3.rd UART (ST-UART) on PXA(XScale) CPUs
627   - trigger watchdog while waiting in serial driver
628
629 * Add auto-update code for TRAB board using USB memory sticks,
630   support new configuration with more memory
631
632 * disable MPC5200 bus pipelining as workaround for bus contention
633
634 * Modify XLB arbiter priorities on MPC5200 so all devices use same
635   priority; configure critical interrupts to be handled like external
636   interrupts
637
638 * Make IPB clock on MGT5100/MPC5200 configurable in board config file;
639   go back to 66 MHz for stability
640
641 * Patches by Jon Diekema, 15 Sep 2003:
642   - add description for missing CFG_CMD_* entries in the README file
643   - sacsng tweaks
644
645 * Patch by Gleb Natapov, 14 Sep 2003:
646   enable watchdog support for all MPC824x boards that have a watchdog
647
648 * On MPC5200, restrict FEC to a maximum of 10 Mbps to work around the
649   "Non-octet Aligned Frame" errors we see at 100 Mbps
650
651 * Patch by Sharad Gupta, 14 Sep 2003:
652   fix SPR numbers for upper BAT register ([ID]BAT[4-7][UL])
653
654 * Patch by llandre, 11 Sep 2003:
655   update configuration for PPChameleonEVB board
656
657 * Patch by David Müller, 13 Sep 2003:
658   various changes to VCMA9 board specific files
659
660 * Add I2C support for MGT5100 / MPC5200
661
662 * Patch by Rune Torgersen, 11 Sep 2003:
663   Changed default memory option on MPC8266ADS to NOT be Page Based
664   Interleave, since this doesn't work very well with the standard
665   16MB DIMM
666
667 * Patch by George G. Davis, 12 Sep 2003:
668   fix Makefile settings for sk98 driver
669
670 * Patch by Stefan Roese, 12 Sep 2003:
671   - new boards added: DP405, HUB405, PLU405, VOH405
672   - some esd boards updated
673   - cpu/ppc4xx/sdram.c: disable memory controller before setting
674     first values
675   - cpu/ppc4xx/405_pci.c: set vendor id on PPC405EP systems
676
677 * Patch by Martin Krause, 11 Sep 2003:
678   add burn-in tests for TRAB board
679
680 * Enable instruction cache on MPC5200 board
681
682 * Patch by Denis Peter, 11 Sep 2003:
683   - fix USB data pointer assignment for bulk only transfer.
684   - prevent to display erased directories in FAT filesystem.
685
686 * Change output format for NAND flash - make it look like for other
687   memory, too
688
689 ======================================================================
690 Changes for U-Boot 0.4.8:
691 ======================================================================
692
693 * Add I2C and RTC support for RMU board
694
695 * Patches by Denis Peter, 9 Sep 2003:
696   add FAT support for IDE, SCSI and USB
697
698 * Patches by Gleb Natapov, 2 Sep 2003:
699   - cleanup of POST code for unsupported architectures
700   - MPC824x locks way0 of data cache for use as initial RAM;
701     this patch unlocks it after relocation to RAM and invalidates
702     the locked entries.
703
704 * Patch by Gleb Natapov, 30 Aug 2003:
705   new I2C driver for mpc107 bridge. Now works from flash.
706
707 * Patch by Dave Ellis, 11 Aug 2003:
708   - JFFS2: fix typo in common/cmd_jffs2.c
709   - JFFS2: fix CFG_JFFS2_SORT_FRAGMENTS option
710   - JFFS2: remove node version 0 warning
711   - JFFS2: accept JFFS2 PADDING nodes
712   - SXNI855T: add AM29LV800 support
713   - SXNI855T: move environment from EEPROM to flash
714   - SXNI855T: boot from JFFS2 in NOR or NAND flash
715
716 * Patch by Bill Hargen, 11 Aug 2003:
717   fixes for I2C on MPC8240
718   - fix i2c_write routine
719   - fix iprobe command
720   - eliminates use of global variables, plus dead code, cleanup.
721
722 * Add support for USB Mass Storage Devices (BBB)
723   (tested with USB memory sticks only)
724
725 * Avoid flicker on TRAB's VFD
726
727 * Add support for SK98xx driver
728
729 * Add PCI support for SL8245 board
730
731 * Support IceCube board configurations with 1 x AMD AM29LV065 (8 MB)
732   or 1 x AM29LV652 (two LV065 in one chip = 16 MB);
733   Run IPB at 133 Mhz; adjust the MII clock frequency accordingly
734
735 * Set BRG_CLK on PM825/826 to 64MHz (VCO_OUT / 4, instead of 16  MHz)
736   to allow for more accurate baudrate settings
737   (error now 0.7% at 115 kbps, instead of 3.5% before)
738
739 * Patch by Andreas Mohr, 4 Sep 2003:
740   Fix a lot of spelling errors
741
742 * Add support for PPChameleon Eval Board
743
744 * Add support for P3G4 board
745
746 * Fix problem with MGT5100 FEC driver: add "early" MAC address
747   initialization
748
749 * Patch by Yuli Barcohen, 7 Aug 2003:
750   check BCSR to detect if the board is configured in PCI mode
751
752 ======================================================================
753 Changes for U-Boot 0.4.7:
754 ======================================================================
755
756 * Patch by Raghu Krishnaprasad, 7 Aug 2003:
757   add support for Adder II MPC852T module
758
759 * Patch by George G. Davis, 19 Aug 2003:
760   fix TI Innovator/OMAP1510 pin configs
761
762 * Patches by Kshitij, 18 Aug 2003
763   - add support for arm926ejs cpu core
764   - add support for TI OMAP 1610 Innovator Board
765
766 * Patch by Yuli Barcohen, 14 Aug 2003:
767   add support for bzip2 uncompression
768
769 * Add GCC library to examples/Makefile so GCC utility functions will
770   be resolved, too
771
772 * Add I2C and RTC support for RMU board using software I2C driver
773   (because of better response to iprobe command); fix problem with
774   "reset" command
775
776 * Patch by Matthias Fuchs, 28 Aug 2003:
777   Added CONFIG_BOOTP_DNS2 and CONFIG_BOOTP_SEND_HOSTNAME to
778   CONFIG_BOOTP_MAKS (see README).
779
780 * Fix ICU862 environment problem
781
782 * Fix RAM size detection for RMU board
783
784 * Implement "reset" for MGT5100/MPC5200 systems
785
786 ======================================================================
787 Changes for U-Boot 0.4.6:
788 ======================================================================
789
790 * Make Ethernet autonegotiation on INCA-IP work for all clock rates;
791   allow selection of clock frequency as "make" target
792
793 * Implement memory autosizing code for IceCube boards
794
795 * Configure network port on INCA-IP for autonegotiation
796
797 * Fix overflow problem in network timeout code
798
799 * Patch by Richard Woodruff, 8 Aug 2003:
800   Allow crc32 to be used at address 0x000 (crc32_no_comp, too).
801
802 ======================================================================
803 Changes for U-Boot 0.4.5:
804 ======================================================================
805
806 * Update for TQM board defaults:
807   disable clocks_in_mhz, enable boot count limit
808
809 * Removed tools/gdb from "make all" target.  Added make target "gdbtools"
810   in toplevel directory instead.  Removed astest.c from tools/gdb because
811   it is no longer relevant.
812
813 * Fix PCI support for MPC5200 / IceCube Board
814
815 * Map ISP1362 USB OTG controller for NSCU board
816
817 * Patch by Brad Parker, 02 Aug 2003:
818   fix sc520_cdp problems
819
820 * Implement Boot Cycle Detection (Req. 2.3 of OSDL CGL Reqirements)
821
822 * Allow erase command to cross flash bank boundaries
823
824 * Patch by Scott McNutt, 21 Jul 2003:
825   Add support for LynuxWorks Kernel Downloadable Images (KDIs).
826   Both LynxOS and BlueCat linux KDIs are supported.
827
828 * Patch by Richard Woodruff, 25 Jul 2003:
829   use more reliable reset for OMAP/925T
830
831 * Patch by Nye Liu, 25 Jul 2003:
832   fix typo in mpc8xx.h
833
834 * Patch by Richard Woodruff, 24 Jul 2003:
835   Fixes for cmd_nand.c:
836   - Fixed null dereferece which could result in incorrect ECC values.
837   - Added support for devices with no Ready/Busy signal hooked up.
838   - Added OMAP1510 read/write protect handling.
839   - Fixed nand.h's ECCPOS. A conflict existed with POS5 and badblock
840     for non-JFFS2.
841   - Switched default ECC to be JFFS2.
842
843 * Allow crc32 to be used at address 0x000
844
845 * Provide consistent interface to standalone applications to access
846   the 'global_data' structure
847   Provide a doc/README.standalone more useful to users/developers.
848
849 * Make IceCube MGT5100 FEC driver work
850
851 * Implement new mechanism to export U-Boot's functions to standalone
852   applications: instead of using (PPC-specific) system calls we now
853   use a jump table; please see doc/README.standalone for details
854
855 * Patch by Dave Westwood, 24 Jul 2003:
856   added support for Unity OS (a proprietary OS)
857
858 * Patch by Detlev Zundel, 23 Jul 2003:
859   add "imls" command to print flash table of contents
860
861 * Fix cold boot detection for log buffer reset
862
863 * Return error for invalid length specifiers with "cp.X" etc.
864
865 * Fix startup problem on MIPS
866
867 * Allow for CONFIG_SPLASH_SCREEN even when no explicit
868   bitmap support is configured
869
870 * Patch by Bill Hargen, 18 Jul 2003:
871   - fix endinaness problem in cpu/mpc824x/drivers/i2c/i2c1.c
872
873 * Patch by Denis Peter, 18 Jul 2003:
874   - fix memory configuration for MIP405T
875   - fix printout of baudrate for "loadb <loadaddr> <baudrate>"
876
877 * Cleanup of TQM82xx configurations; use "official" board types
878   to make selection easier.
879
880 * Patch by Martin Krause, 17 Jul 2003:
881   add delay to get I2C working with "imm" command and s3c24x0_i2c.c
882
883 * Patch by Richard Woodruff, 17 July 03:
884   - Fixed bug in OMAP1510 baud rate divisor settings.
885
886 * Patch by Nye Liu, 16 July 2003:
887   MPC860FADS fixes:
888   - add MPC86xADS support (uses MPC86xADS.h)
889   - add 866P/T core support (also MPC859T/MPC859DSL/MPC852T)
890     o PLPRCR changes
891     o BRG changes (EXTAL/XTAL restricted to 10MHz)
892     o don't trust gclk() software measurement by default, depend on
893       CONFIG_8xx_GCLK_FREQ
894   - add DRAM SIMM not installed detection
895   - use more "correct" SDRAM initialization sequence
896   - allow different SDRAM sizes (8xxADS has 8M)
897   - default DER is 0
898   - remove unused MAMR defines from FADS860T.h (all done in fads.c)
899   - rename MAMR/MBMR defines to be more consistent. Should eventually
900     be merged into MxMR to better reflect the PowerQUICC datasheet.
901
902 * Patch by Yuli Barcohen, 16 Jul 2003:
903   support new Motorola PQ2FADS-ZU evaluation board which replaced
904   MPC8260ADS and MPC8266ADS
905
906 ======================================================================
907 Changes for U-Boot 0.4.4:
908 ======================================================================
909
910 * Add support for IceCube board (with MGT5100 and MPC5200 CPUs)
911
912 * Add support for MGT5100 and MPC5200 processors
913
914 * Patch by Lutz Dennig, 15 Jul 2003:
915   update for R360MPI board
916
917 ======================================================================
918 Changes for U-Boot 0.4.3:
919 ======================================================================
920
921 * Patches by Kshitij, 04 Jul 2003
922   - added support for arm925t cpu core
923   - added support for TI OMAP 1510 Innovator Board
924
925 * Patches by Martin Krause, 14 Jul 2003:
926   - add I2C support for s3c2400 systems (trab board)
927   - (re-) add "ping" to command table
928
929 * Fix handling of "slow" POST routines
930
931 * Patches by Yuli Barcohen, 13 Jul 2003:
932   - Correct flash and JFFS2 support for MPC8260ADS
933   - fix PVR values and clock generation for PowerQUICC II family
934     (8270/8275/8280)
935
936 * Patch by Bernhard Kuhn, 08 Jul 2003:
937   - add support for M68K targets
938
939 * Patch by Ken Chou, 3 Jul:
940   - Fix PCI config table for A3000
941   - Fix iobase for natsemi.c
942     (PCI_BASE_ADDRESS_0 is the IO base register for DP83815)
943
944 * Allow to enable "slow" POST routines by key press on power-on
945 * Fix temperature dependend switching of LCD backlight on LWMON
946 * Tweak output format for LWMON
947
948 * Patch by Stefan Roese, 11 Jul 2003:
949   - Fix bug in CONFIG_VERSION_VARIABLE.
950   - AR405 config updated.
951   - OCRTC/ORSG: bsp command added.
952   - ASH405 bsp update.
953
954 ======================================================================
955 Changes for U-Boot 0.4.2:
956 ======================================================================
957
958 * Add support for NSCU board
959
960 * Add support for TQM823M, TQM850M, TQM855M and TQM860M modules
961
962 * Add support for Am29LV160ML, Am29LV320ML, and Am29LV640ML
963   mirror bit flash on TQM8xxM modules
964
965 * Patch by Kenneth Johansson, 30 Jun 2003:
966   get rid of MK_CMD_ENTRY macro; update doc/README.command
967
968 * Patch by Seb James, 30 Jun 2003:
969   Improve documentation of I2C configuration in README
970
971 * Fix problems with previous log buffer "fixes"
972
973 * Fix minor help text issues
974
975 * "log append" did not append a newline
976
977 ======================================================================
978 Changes for U-Boot 0.4.1:
979 ======================================================================
980
981 * Fix some missing commands, cleanup header files
982   (autoscript, bmp, bsp, fat, mmc, nand, portio, ...)
983
984 * Rewrite command lookup and help command (fix problems with bubble
985   sort when sorting command name list). Minor cleanup here and there.
986
987 * Merge from "stable branch", tag LABEL_2003_06_28_1800-stable:
988   - Allow to call sysmon function interactively
989   - PIC on LWMON board needs delay after power-on
990   - Add missing RSR definitions for MPC8xx
991   - Improve log buffer handling: guarantee clean reset after power-on
992   - Add support for EXBITGEN board (aka "genie")
993   - Add support for SL8245 board
994
995 * Code cleanup:
996   - remove trailing white space, trailing empty lines, C++ comments, etc.
997   - split cmd_boot.c (separate cmd_bdinfo.c and cmd_load.c)
998
999 * Patches by Kenneth Johansson, 25 Jun 2003:
1000   - major rework of command structure
1001     (work done mostly by Michal Cendrowski and Joakim Kristiansen)
1002
1003 ======================================================================
1004 Changes for U-Boot 0.4.0:
1005 ======================================================================
1006
1007 * Patches by Robert Schwebel, 26 Jun 2003:
1008   - csb226 configuration updated
1009   - credits for logodl port updated
1010   - innokom configuration updated
1011   - logodl tree update, still with coding style inconsistencies
1012   - added OCM for ppc405 warning to README
1013
1014 * Patch by Pantelis Antoniou, 25 Jun 2003:
1015   update NetVia with V2 board support
1016
1017 * Header file cleanup for ARM
1018
1019 * Patch by Murray Jensen, 24 Jun 2003:
1020   - make sure to use only U-boot provided header files
1021   - fix problems with ".rodata.str1.4" section as used by GCC-3.x
1022
1023 * Patch by Stefan Roese, 24 Jun 2003:
1024   - Update esd ASH405 board files.
1025   - Update esd DASA_SIM config file.
1026   - Add ping command to some esd boards.
1027
1028 * Patch by Yuli Barcohen, 23 Jun 2003:
1029   Update for MPC8260ADS board
1030
1031 * Patch by Murray Jensen, 23 Jun 2003:
1032   - cleanup of GCC 3.x compiler warnings
1033
1034 * Patch by Rune Torgersen, 4 Jun 2003:
1035   add large memory support for MPC8266ADS board
1036
1037 * Patch by Richard Woodruff, 19 June 03:
1038   - Enabled standard u-boot device abstraction for ARM
1039   - Enabled console device for ARM
1040   - Initilized bi_baudrate for ARM
1041
1042 * Patch by Bill Hargen, 23 Apr 2003:
1043   fix byte order for 824x I2C addresses (write op)
1044
1045 * Patch by Murray Jensen, 20 Jun 2003:
1046   - hymod update
1047   - cleanup (especially for gcc-3.x compilers)
1048
1049 * Patch by Tom Guilliams, 20 Jun 2003:
1050   added CONFIG_750FX support for IBM 750FX processors
1051
1052 * Patch by Devin Crumb, 02 Apr 2003:
1053   Fix clock divider rounding problem in drivers/serial.c
1054
1055 * Patch by Richard Woodruff, 19 June 03:
1056   - Fixed smc91c111 driver to sync with the u-boot environment
1057     (driver/smc91c111.c).
1058   - Added eth_init error return check in NetLoop (net/net.c).
1059
1060 * Patch by Ken Chou, 19 June 2003:
1061   Added support for A3000 SBC board (Artis Microsystems Inc.)
1062
1063 * Patches by Murray Jensen, 17 Jun 2003:
1064   - Hymod board database mods: add "who" field and new xilinx chip types
1065   - provide new "init_cmd_timeout()" function so code external to
1066     "common/main.c" can use the "reset_cmd_timeout()" function before
1067     entering the main loop
1068   - add DTT support for adm1021 (new file dtt/adm1021.c; config
1069     slightly different. see include/configs/hymod.h for an example
1070     (requires CONFIG_DTT_ADM1021, CONFIG_DTT_SENSORS, and
1071     CFG_DTT_ADM1021 defined)
1072   - add new "eeprom_probe()" function which has similar args and
1073     behaves in a similar way to "eeprom_read()" etc.
1074   - add 8260 FCC ethernet loopback code (new "eth_loopback_test()"
1075     function which is enabled by defining CONFIG_ETHER_LOOPBACK_TEST)
1076   - gdbtools copyright update
1077   - ensure that set_msr() executes the "sync" and "isync" instructions
1078     after the "mtmsr" instruction in cpu/mpc8260/interrupts.c
1079   - 8260 I/O ports fix: Open Drain should be set last when configuring
1080   - add SIU IRQ defines for 8260
1081   - allow LDSCRIPT override and OBJCFLAGS initialization: change to
1082     config.mk to allow board configurations to override the GNU
1083     linker script, selected via the LDSCRIPT, make variable, and to
1084     give an initial value to the OBJCFLAGS make variable
1085   - 8260 i2c enhancement:
1086     o correctly extends the timeout depending on the size of all
1087       queued messages for both transmit and receive
1088     o will not continue with receive if transmit times out
1089     o ensures that the error callback is done for all queued tx
1090       and rx messages
1091     o correctly detects both tx and rx timeouts, only delivers one to
1092       the callback, and does not overwrite an earlier error
1093     o logic in i2c_probe now correct
1094   - add "vprintf()" function so that "panic()" function can be
1095     technically correct
1096   - many Hymod board changes
1097
1098 * Patches by Robert Schwebel, 14 Jun 2003:
1099   - add support for Logotronic DL datalogger board
1100   - cleanup serial line after kermit binary download
1101   - add debugX macro (debug level support)
1102   - update mach-types.h to latest arm.linux.org.uk master list.
1103
1104 * Patches by David Müller, 12 Jun 2003:
1105   - rewrite of the S3C24X0 register definitions stuff
1106   - "driver" for the built-in S3C24X0 RTC
1107
1108 * Patches by Yuli Barcohen, 12 Jun 2003:
1109   - Add MII support and Ethernet PHY initialization for MPC8260ADS board
1110   - Fix incorrect SIUMCR initialisation caused by wrong Hard Reset
1111     configuration word supplied by FPGA on some MPC8260ADS boards
1112
1113 * Patch by Pantelis Antoniou, 10 Jun 2003:
1114   Unify status LED interface
1115
1116 * Add support for DS12887 RTC; add RTC support for ATC board
1117
1118 * Patch by Nicolas Lacressonniere, 11 Jun 2003:
1119   Modifications for Atmel AT91RM9200DK ARM920T based development kit
1120   - Add Atmel DataFlash support for reading and writing.
1121   - Add possibility to boot a Linux from DataFlash with BOOTM command.
1122   - Add Flash detection on Atmel AT91RM9200DK
1123     (between Atmel AT49BV1614 and AT49BV1614A flashes)
1124   - Replace old Ethernet PHY layer functions
1125   - Change link address
1126
1127 * Patch by Frank Smith, 9 Jun 2003:
1128   use CRIT_EXCEPTION for machine check on 4xx
1129
1130 * Patch by Detlev Zundel, 13 Jun 2003:
1131   added implementation of the "carinfo" command in cmd_immap.c
1132
1133 * Fix CONFIG_NET_MULTI support in include/net.h
1134
1135 * Patches by Kyle Harris, 13 Mar 2003:
1136   - Add FAT partition support
1137   - Add command support for FAT
1138   - Add command support for MMC
1139   ----
1140   - Add Intel PXA support for video
1141   - Add Intel PXA support for MMC
1142   ----
1143   - Enable MMC and FAT for lubbock board
1144   - Other misc changes for lubbock board
1145
1146 * Patch by Robert Schwebel, April 02, 2003:
1147   fix for SMSC91111 driver
1148
1149 * Patch by Vladimir Gurevich, 04 Jun 2003:
1150   make ppc405 ethernet driver compatible with CONFIG_NET_MULTI option
1151
1152 * Patch by Stefan Roese, 05 Jun 2003:
1153   - PPC4xx: Fix bug for initial stack in data cache as pointed out by
1154     Thomas Schaefer (tschaefer@giga-stream.de). Now inital stack in
1155     data cache can be used even if the chip select is in use.
1156   - CFG_RX_ETH_BUFFER added to set the ethernet receive buffer count
1157     (see README for further description).
1158   - Changed config files of CONFIG_EEPRO100 boards to use the
1159     CFG_RX_ETH_BUFFER define.
1160
1161 * Add support for RMU board
1162
1163 * Add support for TQM862L at 100/50 MHz
1164
1165 * Patch by Pantelis Antoniou, 02 Jun 2003:
1166   major reconstruction of networking code;
1167   add "ping" support (outgoing only!)
1168
1169 * Patch by Denis Peter, 04 June 2003:
1170   add support for the MIP405T board
1171
1172 * Patches by Udi Finkelstein, 2 June 2003:
1173   - Added support for custom keyboards, initialized by defining a
1174     board-specific drv_keyboard_init as well as defining CONFIG_KEYBOARD .
1175   - Added support for the RBC823 board.
1176   - cpu/mpc8xx/lcd.c now automatically calculates the
1177     Horizontal Pixel Count field.
1178
1179 * Fix alignment problem in BOOTP (dhcp_leasetime option)
1180   [pointed out by Nicolas Lacressonnière, 2 Jun 2003]
1181
1182 * Patch by Mark Rakes, 14 May 2003:
1183   add support for Intel e1000 gig cards.
1184
1185 * Patch by Nye Liu, 3 Jun 2003:
1186   fix critical typo in MAMR definition (include/mpc8xx.h)
1187
1188 * Fix requirement to align U-Boot image on 16 kB boundaries on PPC.
1189
1190 * Patch by Klaus Heydeck, 2 Jun 2003
1191   Minor changes for KUP4K configuration
1192
1193 * Patch by Marc Singer, 29 May 2003:
1194   Fixed rarp boot method for IA32 and other little-endian CPUs.
1195
1196 * Patch by Marc Singer, 28 May 2003:
1197   Added port I/O commands.
1198
1199 * Patch by Matthew McClintock, 28 May 2003
1200   - cpu/mpc824x/start.S: fix relocation code when booting from RAM
1201   - minor patches for utx8245
1202
1203 * Patch by Daniel Engström, 28 May 2003:
1204   x86 update
1205
1206 * Patch by Dave Ellis, 9 May 2003 + 27 May 2003:
1207   add nand flash support to SXNI855T configuration
1208   fix/extend nand flash support:
1209   - fix 'nand erase' command so does not erase bad blocks
1210   - fix 'nand write' command so does not write to bad blocks
1211   - fix nand_probe() so handles no flash detected properly
1212   - add doc/README.nand
1213   - add .jffs2 and .oob options to nand read/write
1214   - add 'nand bad' command to list bad blocks
1215   - add 'clean' option to 'nand erase' to write JFFS2 clean markers
1216   - make NAND read/write faster
1217
1218 * Patch by Rune Torgersen, 23 May 2003:
1219   Update for MPC8266ADS board
1220
1221 * Get (mostly) rid of CFG_MONITOR_LEN definition; compute real length
1222   instead CFG_MONITOR_LEN is now only used to determine  _at_compile_
1223   _time_  (!) if the environment is embedded within the U-Boot image,
1224   or in a separate flash sector.
1225
1226 * Cleanup CFG_DER #defines in config files (wd maintained only)
1227
1228 * Fix data abort exception handling for arm920t CPU
1229
1230 * Fix alignment problems with flash driver for TRAB board
1231
1232 * Patch by Donald White, 21 May 2003:
1233   fix calculation of base address in pci_hose_config_device()
1234
1235 * Fix bug in command line parsing: "cmd1;cmd2" is supposed to always
1236   execute "cmd2", even if "cmd1" fails. Note that this is different
1237   to "run var1 var2" where the contents of "var2" will NOT be
1238   executed when a command in "var1" fails.
1239
1240 * Add zero-copy ramdisk support (requires corresponding kernel support!)
1241
1242 * Patch by Kyle Harris, 20 May 2003:
1243   In preparation for an ixp port, rename cpu/xscale and arch-xscale
1244   into cpu/pxa and arch-pxa.
1245
1246 * Patch by Stefan Roese, 23 May 2003:
1247   - IBM PPC405EP port added.
1248   - CONFIG_UART1_CONSOLE added. If defined internal UART1 (and not
1249     UART0) is used as default U-Boot console. PPC4xx only!
1250   - esd ASH405 board added (PPC405EP based).
1251   - BUBINGA405EP board added (PPC405EP based - IBM Eval Board).
1252   - esd CPCI405AB board added.
1253   - esd PMC405 board added.
1254   - Update of some esd boards.
1255
1256 * Patch by Denis Peter, 19 Mai 2003:
1257   add support for the MIP405-3 board
1258
1259 * Patch by Dave Ellis, 22 May 2003:
1260   Fix problem with only partially cleared .bss segment
1261
1262 * Patch by Rune Torgersen, 12 May 2003:
1263   get PCI to work on a MPC8266ADS board; incorporate change to
1264   cpu/mpc8260/pci.c to enable overrides of PCI memory parameters
1265
1266 * Patch by Nye Liu, 1 May 2003:
1267   minor patches for the FADS8xx
1268
1269 * Patch by Thomas Schäfer, 28 Apr 2003:
1270   Fix SPD handling for 256 ECC DIMM on Walnut
1271
1272 * Add support for arbitrary bitmaps for TRAB's  VFD command;
1273   allow to pass boot bitmap addresses in environment variables;
1274   allow for zero boot delay
1275
1276 * Patch by Christian Geißinger, 19 May 2002:
1277   On TRAB: wait until the dummy byte has been completely sent
1278
1279 * Patch by David Updegraff, 22 Apr 2003:
1280   update for CrayL1 board
1281
1282 * Patch by Pantelis Antoniou, 21 Apr 2003:
1283   add boot support for ARTOS (a proprietary OS)
1284
1285 * Patch by Steven Scholz, 11 Apr 2003:
1286   Add support for RTC DS1338
1287
1288 * Patch by Rod Boyce, 24 Jan 2003:
1289   Fix counting of extended partitions in diskboot command
1290
1291 * Patch by Christophe Lindheimer, 20 May 2003:
1292   allow the use of CFG_LOADS when CFG_NO_FLASH is set
1293
1294 * Fix SDRAM timing on Purple board
1295
1296 * Add support for CompactFlash on ATC board
1297   (includes support for Intel 82365 and compatible PC Card controllers,
1298   and Yenta-compatible PCI-to-CardBus controllers)
1299
1300 * Patch by Mathijs Haarman, 08 May 2003:
1301   Add lan91c96 driver (tested on Lubbock and custom PXA250 board only)
1302
1303 * Fix problem with usage of "true" (undefined in current versions of bfd.h)
1304
1305 * Add support for Promess ATC board
1306
1307 * Patch by Keith Outwater, 28 Apr 2003:
1308   - Miscellaneous corrections and additions to GEN860T board specific code.
1309   - Added GEN860_SC variant to GEN860T.
1310   - Miscellaneous corrections to GEN860T documentation.
1311   - Correct duplicate entry in U-Boot CREDITS file.
1312   - Add GEN860T_SC entry in MAINTAINERS file.
1313   - Update CREDITS file with GEN860T_SC info.
1314
1315 * Update Smiths Aerospace addresses in MAINTAINERS file
1316
1317 * Fix error handling in hush's version of "run" command
1318
1319 * LWMON extensions:
1320   - Splashscreen support
1321   - modem support
1322   - sysmon support
1323   - temperature dependend enabling of LCD
1324
1325 * Allow booting from old "PPCBoot" disk partitions
1326
1327 * Add support for TQM8255 Board / MPC8255 CPU
1328
1329 ======================================================================
1330 Changes for U-Boot 0.3.1:
1331 ======================================================================
1332
1333 * Make sure Block Lock Bits get cleared in R360MPI flash driver
1334
1335 * MPC823 LCD driver: Fill color map backwards, to allow for steady
1336   display when Linux takes over
1337
1338 * Patch by Erwin Rol, 27 Feb 2003:
1339   Add support for RTEMS (this time for real).
1340
1341 * Add support for "bmp info" and "bmp display" commands to load
1342   bitmap images; this can be used (for example in a "preboot"
1343   command) to display a splash screen very quickly after poweron.
1344
1345 * Add support for 133 MHz clock on INCA-IP board
1346
1347 * Patch by Lutz Dennig, 10 Apr 2003:
1348   Update for R360MPI board
1349
1350 * Add new meaning to "autostart" environment variable:
1351   If set to "no", a standalone image passed to the
1352   "bootm" command will be copied to the load address
1353   (and eventually uncompressed), but NOT be started.
1354   This can be used to load and uncompress arbitrary
1355   data.
1356
1357 * Patch by Stefan Roese, 10 Apr 2003:
1358   Changed DHCP client to use IP address from server option field #54
1359   from the OFFER packet in the server option field #54 in the REQUEST
1360   packet. This fixes a problem using a Windows 2000 DHCP server,
1361   where the DHCP-server is not the TFTP-server.
1362
1363 * Set max brightness for MN11236 displays on TRAB board
1364
1365 * Add support for TQM862L modules
1366
1367 ======================================================================
1368 Changes for U-Boot 0.3.0:
1369 ======================================================================
1370
1371 * Patch by Arun Dharankar, 4 Apr 2003:
1372   Add IDMA example code (tested on 8260 only)
1373
1374 * Add support for Purple Board (MIPS64 5Kc)
1375
1376 * Add support for MIPS64 5Kc CPUs
1377
1378 * Fix missing setting of "loadaddr" and "bootfile" on ARM and MIPS
1379
1380 * Patch by Denis Peter, 04 Apr 2003:
1381   - update MIP405-4 board
1382
1383 * Patch by Stefan Roese, 4 Apr 2003:
1384   - U-Boot version environment variable "ver" added
1385     (CONFIG_VERSION_VARIABLE).
1386   - Changed PPC405GPr version from A to B.
1387   - Changed CPCI405 to use CTS instead of DSR on PPC405 UART1.
1388
1389 * Patches by Denis Peter, 03 April 2003:
1390   - fix PCI IRQs on MPL boards
1391   - fix two more un-relocated pointer problems
1392
1393 * Fix behaviour of "run" command:
1394   - print error message iv variable does not exist
1395   - terminate processing of arguments in case of error
1396
1397 * Patches by Peter Figuli, 10 Mar 2003
1398   - Add support for BTUART on PXA platform
1399   - Add support for WEP EP250 (PXA) board
1400
1401 * Fix flash problems on INCA-IP; add tool to allow bruning images  to
1402   flash using a BDI2000
1403
1404 * Implement fix for I2C Edge Conditions problem for all boards that
1405   use the bit-banging driver (common/soft_i2c.c)
1406
1407 * Patch by Martin Winistoerfer, 23 Mar 2003
1408   - Add port to MPC555/556 microcontrollers
1409   - Add support for cmi customer board with
1410     Intel 28F128J3A, 28F320J3A or 28F640J3A flash.
1411
1412 * Patch by Rick Bronson, 28 Mar 2003:
1413   - fix common/cmd_nand.c
1414
1415 * Patch by Arun Dharankar, 24 Mar 2003:
1416   - add threads / scheduler example code
1417
1418 * Add patches by Robert Schwebel, 31 Mar 2003:
1419   - add ctrl-c support for kermit download
1420   - align bdinfo output on ARM
1421   - csb226 board: bring in sync with innokom/memsetup.S
1422   - csb226 board: fix MDREFR handling
1423   - misc doc fixes / extensions
1424   - innokom board: cleanup, MDREFR fix in memsetup.S, config update
1425   - add BOOT_PROGRESS to armlinux.c
1426
1427 * Add CPU ID, version, and clock speed for INCA-IP
1428
1429 * Patches by Dave Ellis, 18 Mar 2003 for SXNI855T board:
1430   - fix SRAM and SDRAM memory sizing
1431   - add status LED support
1432   - add MAC address for second (SCC1) ethernet port
1433
1434 * Update default environment for TQM8260 board
1435
1436 * Patch by Rick Bronson, 16 Mar 2003:
1437   - Add NAND flash support for reading, writing, and erasing NAND
1438     flash (certain forms of which are called SmartMedia).
1439   - Add support for Atmel AT91RM9200DK ARM920T based development kit.
1440
1441 * Patches by Robert Schwebel, 19 Mar 2003:
1442   - use arm-linux-gcc as default compiler for ARM
1443   - fix i2c fixup code
1444   - fix missing baudrate setting
1445   - added $loadaddr / CFG_LOAD_ADDR support to loadb
1446   - moved "ignoring trailing characters" _before_ u-boot wants to
1447     print out diagnostics messages; removes bogus characters at the
1448     end of transmission
1449
1450 * Patch by John Zhan, 18 Mar 2003:
1451   Add support for SinoVee Microsystems SC8xx boards
1452
1453 * Patch by Rolf Offermanns, 21 Mar 2003:
1454   ported the dnp1110 related changes from the current armboot cvs to
1455   current u-boot cvs. smc91111 does not work. problem marked in
1456   smc91111.c, grep for "FIXME".
1457
1458 * Patch by Brian Auld, 25 Mar 2003:
1459   Add support for STM flash chips on ebony board
1460
1461 * Add PCI support for MPC8250 Boards (PM825 module)
1462
1463 * Patch by Stefan Roese, 25 Mar 2003:
1464   - PCI405 update.
1465
1466 * Patch by Stefan Roese, 20 Mar 2003:
1467   - CPCI4052 update (support for revision 3).
1468   - Set edge conditioning circuitry on PPC405GPr for compatibility
1469     to existing PPC405GP designs.
1470   - Clip udiv to 5 bits on PPC405 (serial.c).
1471
1472 * Extend INCAIP board support:
1473   - add automatic RAM size detection
1474   - add "bdinfo" command
1475   - pass flash address and size to Linux kernel
1476   - switch to 150 MHz clock
1477
1478 * Avoid flicker on the TRAB's VFD by synchronizing the enable with
1479   the HSYNC/VSYNC. Requires new CPLD code (Version 101 for Rev. 100
1480   boards, version 153 for Rev. 200 boards).
1481
1482 * Patch by Vladimir Gurevich, 12 Mar 2003:
1483   Fix relocation problem of statically initialized string pointers
1484   in common/cmd_pci.c
1485
1486 * Patch by Kai-Uwe Blöm, 12 Mar 2003:
1487   Cleanup & bug fixes for JFFS2 code:
1488   - the memory mangement was broken. It caused havoc on malloc by
1489     writing beyond the block boundaries.
1490   - the length calculation for files was wrong, sometimes resulting
1491     in short file reads.
1492   - data copying now optionally takes fragment version numbers into
1493     account, to avoid copying from older data.
1494   See doc/README.JFFS2 for details.
1495
1496 * Patch by Josef Wagner, 12 Mar 2003:
1497   - 16/32 MB and 50/80 MHz support with auto-detection for IP860
1498   - ETH05 and BEDBUG support for CU824
1499   - added support for MicroSys CPC45
1500   - new BOOTROM/FLASH0 and DOC base for PM826
1501
1502 * Patch by Robert Schwebel, 12 Mar 2003:
1503   Fix the chpart command on innokom board
1504
1505 * Name cleanup:
1506   mv include/asm-i386/ppcboot-i386.h include/asm-i386/u-boot-i386.h
1507   s/PPCBoot/U-Boot/ in some files
1508   s/pImage/uImage/  in some files
1509
1510 * Patch by Detlev Zundel, 15 Jan 2003:
1511   Fix '' command line quoting
1512
1513 * Patch by The LEOX team, 19 Jan 2003:
1514   - add support for the ELPT860 board
1515   - add support for Dallas ds164x RTC
1516
1517 * Patches by David Müller, 31 Jan 2003:
1518   - minimal setup for CardBus bridges
1519   - add EEPROM read/write support in the CS8900 driver
1520   - add support for the builtin I2C controller in the Samsung s3c24x0 chips
1521   - add support for MPL's VCMA9 (Samsung s3c2410 based) board
1522
1523 * Patch by Steven Scholz, 04 Feb 2003:
1524   add support for RTC DS1307
1525
1526 * Patch by Reinhard Meyer, 5 Feb 2003:
1527   fix PLPRCR/SCCR init sequence on 8xx to allow for
1528   changes of EBDF by software
1529
1530 * Patch by Vladimir Gurevich, 07 Feb 2003:
1531   "API-compatibility patch" for 4xx I2C driver
1532
1533 * TRAB fixes / extensions:
1534   - Restore VFD brightness as saved in environment
1535   - add support for Fujitsu flashes
1536   - make sure both buzzers are turned off (drive low level)
1537
1538 * Patches by Robert Schwebel, 06 Mar 2003:
1539   - fix bug in BOOTP code (must use NetCopyIP)
1540   - update of CSB226 port
1541   - clear BSS segment on XScale
1542   - added support for i2c_init_board() function
1543   - update to the Innokom plattform
1544
1545 * Extend support for redundand environments for configurations where
1546   environment size < sector size
1547
1548 * Patch by Rune Torgersen, 13 Feb 2003:
1549   Add support for Motorola MPC8266ADS board
1550
1551 * Patch by Kyle Harris, 19 Feb 2003:
1552   patches for the Intel lubbock board:
1553   memsetup.S - general cleanup (based on Robert's csb226 code)
1554   flash.c - overhaul, actually works now
1555   lubbock.c - fix init funcs to return proper value
1556
1557 * Patch by Kenneth Johansson, 26 Feb 2003:
1558   - Fixed off by one in RFTA calculation.
1559   - No need to abort when LDF is lower than we can program it's only
1560     minimum timing so clamp it to what we can do.
1561   - Takes function pointer to function for reading the spd_nvram. Usefull
1562     for faking data or hardcode a module without the nvram.
1563   - fix other user for above change
1564   - fix some comments.
1565
1566 * Patches by Brian Waite, 26 Feb 2003:
1567   - fix port for evb64260 board
1568   - fix PCI for evb64260 board
1569   - fix PCI scan
1570
1571 * Patch by Reinhard Meyer, 1 Mar 2003:
1572   Add support for EMK TOP860 Module
1573
1574 * Patch by Yuli Barcohen, 02 Mar 2003:
1575   Add SPD EEPROM support for MPC8260ADS board
1576
1577 * Patch by Robert Schwebel, 21 Jan 2003:
1578   - Add support for Innokom board
1579   - Don't complain if "install" fails
1580   - README cleanup (remove duplicated lines)
1581   - Update PXA header files
1582
1583 * Add documentation for existing POST code (doc/README.POST)
1584
1585 * Patch by Laudney Ren, 15 Jan 2003:
1586   Fix handling of redundand environment in "tools/envcrc.c"
1587
1588 * Patch by Detlev Zundel, 28 Feb 2003:
1589   Add bedbug support for 824x systems
1590
1591 * Add support for 16 MB flash configuration of TRAB board
1592
1593 * Patch by Erwin Rol, 27 Feb 2003:
1594   Add support for RTEMS
1595
1596 * Add image information to README
1597
1598 * Patch by Stefan Roese, 18 Feb 2003:
1599   CPCIISER4 configuration updated.
1600
1601 * Patch by Stefan Roese, 17 Feb 2003:
1602   Fixed bug in ext. serial clock setup on PPC405 (since PPC440 port).
1603
1604 * Patch by Stefan Roese, 13 Feb 2003:
1605   Add "pcidelay" environment variable (in ms, enabled via
1606   CONFIG_PCI_BOOTDELAY).
1607   PCI spec 2.2 defines, that a pci target has 2^25 pci clocks after
1608   RST# to respond to configuration cycles (33MHz -> 1s).
1609
1610 * Fix dual PCMCIA slot support (when running with just one
1611   slot populated)
1612
1613 * Add VFD type detection to trab board
1614
1615 * extend drivers/cs8900.c driver to synchronize  ethaddr  environment
1616   variable with value in the EEPROM
1617
1618 * Patch by Stefan Roese, 10 Feb 2003:
1619   Add support for 4MB and 128MB onboard SDRAM (cpu/ppc4xx/sdram.c)
1620
1621 * Add support for MIPS32 4Kc CPUs
1622
1623 * Add support for INCA-IP Board
1624
1625 ======================================================================
1626 Changes for U-Boot 0.2.2:
1627 ======================================================================
1628
1629 * Add dual ethernet support on PM826
1630
1631 * Add support for LXT971 PHY on PM826
1632
1633 * Patch by Tord Andersson, 16 Jan 2003:
1634   Fix flash sector count for TQM8xxL
1635
1636 * Fix I2C EEPROM problem on ICU862 board (would only write the first
1637   16 bytes out of each 32 byte block)
1638
1639 ======================================================================
1640 Changes for U-Boot 0.2.1:
1641 ======================================================================
1642
1643 * Add support for V37 board
1644   (patch by Jón Benediktsson, 11 Dec 2002)
1645
1646 * Update baudrate in bd_info when it gets changed
1647
1648 * Add watchdog trigger points while waiting for serial port
1649   (so far only 8xx -- needed on LWMON with 100ms watchdog)
1650
1651 * Improve command line tool to access the U-Boot's environment
1652   (figuration of the utility, using a config file)
1653
1654 * Add single quote support for (old) command line parser
1655
1656 * Switch LWMON board default config from FRAM to EEPROM;
1657   in POST, EEPROM shows up on 8 addresses
1658
1659 ======================================================================
1660 Changes for U-Boot 0.2.0:
1661 ======================================================================
1662
1663 * Use 1-byte-read instead of -write for iprobe() function
1664   Add i2c commands to PM826 config
1665
1666 * extend I2C POST code: check for list on known addresses
1667
1668 * Improve log buffer code; use "loglevel" to decide which messages
1669   to log on the console, too (like in Linux); get rid of "logstart"
1670
1671 * Add command line tool to access the U-Boot's environment
1672   (board-specific for TRAB now, to be fixed later)
1673
1674 * Patch by Hans-Joerg Frieden, 06 Dec 2002
1675   Fix misc problems with AmigaOne support
1676
1677 * Patch by Chris Hallinan, 3 Dec 2002:
1678   minor cleanup to the MPC8245 EPIC driver
1679
1680 * Patch by Pierre Aubert , 28 Nov 2002
1681   Add support for external (SIU) interrupts on MPC8xx
1682
1683 * Patch by Pierre Aubert , 28 Nov 2002
1684   Fix nested syscalls bug in standalone applications
1685
1686 * Patch by David Müller, 27 Nov 2002:
1687   fix output of "pciinfo" command for CardBus bridge devices.
1688
1689 * Fix bug in TQM8260 board detection - boards got stuck when board ID
1690   was not readable
1691
1692 * Add LED indication for IDE activity on KUP4K board
1693
1694 * Fix startup problems with VFD display on TRAB
1695
1696 * Patch by Pierre Aubert, 20 Nov 2002
1697   Add driver for Epson SED13806 graphic controller.
1698   Add support for BMP logos in cfb_console driver.
1699
1700 * Added support for both PCMCIA slots (at the same time!) on MPC8xx
1701
1702 * Patch by Rod Boyce, 21 Nov 2002:
1703   fix PCMCIA on MBX8xx board
1704
1705 * Patch by Pierre Aubert , 21 Nov 2002
1706   Add CFG_CPM_POST_WORD_ADDR to make the offset of the
1707   bootmode word in DPRAM configurable
1708
1709 * Patch by Daniel Engström, 18 Nov 2002:
1710   Fixes for x86 port (mostly strings issues)
1711
1712 * Patch by Ken Chou, 18 Nov 2002:
1713   Fix for natsemi NIC cards (DP83815)
1714
1715 * Patch by Pierre Aubert, 19 Nov 2002:
1716   fix a bug for the MII configuration, and some warnings
1717
1718 * Patch by Thomas Frieden, 13 Nov 2002:
1719   Add code for AmigaOne board
1720   (preliminary merge to U-Boot, still WIP)
1721
1722 * Patch by Jon Diekema, 12 Nov 2002:
1723   - Adding URL for IEEE OUI lookup
1724   - Making the autoboot #defines dependent on CONFIG_AUTOBOOT_KEYED
1725     being defined.
1726   - In the CONFIG_EXTRA_ENV_SETTINGS #define, the root-on-initrd and
1727     root-on-nfs macros are designed to switch how the default boot
1728     method gets defined.
1729
1730 * Patch by Daniel Engström, 13 Nov 2002:
1731   Add support for i386 architecture and AMD SC520 board
1732
1733 * Patch by Pierre Aubert, 12 Nov 2002:
1734   Add support for DOS filesystem and booting from DOS floppy disk
1735
1736 * Patch by Jim Sandoz, 07 Nov 2002:
1737   Increase number of network RX buffers (PKTBUFSRX in
1738   "include/net.h") for EEPRO100 based boards (especially SP8240)
1739   which showed "Receiver is not ready" errors when U-Boot was
1740   processing the receive buffers slower than the network controller
1741   was filling them.
1742
1743 * Patch by Andreas Oberritter, 09 Nov 2002:
1744   Change behaviour of NetLoop(): return -1 for errors, filesize
1745   otherwise; return code 0 is valid an means no file loaded - in this
1746   case the environment still gets updated!
1747
1748 * Patches by Jon Diekema, 9 Nov 2002:
1749   - improve ADC/DAC clocking on the SACSng board to align
1750     the failing edges of LRCLK and SCLK
1751   - sbc8260 configuration tweaks
1752   - add status LED support for 82xx systems
1753   - wire sspi/sspo commands into command handler; improved error
1754     handlering
1755   - add timestamp support and alternate memory test to the
1756     SACSng configuration
1757
1758 * Patch by Vince Husovsky, 7 Nov 2002:
1759   Add "-n" to linker options to get rid of "Not enough room for
1760   program headers" problem
1761
1762 * Patch by David Müller, 05 Nov 2002
1763   Rename CONFIG_PLL_INPUT_FREQ to CONFIG_SYS_CLK_FREQ
1764   so we can use an already existing name
1765
1766 * Patch by Pierre Aubert, 05 Nov 2002
1767   Hardware relatied improvments in FDC boot code
1768
1769 * Patch by Holger Schurig, 5 Nov 2002:
1770   Make the PXA really change it's frequency
1771
1772 * Patch by Pierre Aubert, 05 Nov 2002
1773   Add support for slave serial Spartan 2 FPGAs
1774
1775 * Fix uninitialized memory (MAC  address)  in  8xx  SCC/FEC  ethernet
1776   drivers
1777
1778 * Add support for log buffer which can be passed to Linux kernel's
1779   syslog mechanism; used especially for POST results.
1780
1781 * Patch by Klaus Heydeck, 31 Oct 2002:
1782   Add initial support for kup4k board
1783
1784 * Patch by Robert Schwebel, 04 Nov 2002:
1785   - use watchdog to reset PXA250 systems
1786   - added progress callbacks to (some of the) ARM code
1787   - update for Cogent CSB226 board
1788
1789 * Add support for FPS860 board
1790
1791 * Patch by Guillaume Alexandre,, 04 Nov 2002:
1792   Improve PCI access on 32-bits Compact PCI bus
1793
1794 * Fix mdelay() on TRAB - this was still the debugging version with
1795   seconds instead of ms.
1796
1797 * Patch by Robert Schwebel, 1 Nov 2002:
1798   XScale related cleanup (affects all ARM boards)
1799
1800 * Cleanup of names and README.
1801
1802 ======================================================================
1803 Notes for U-Boot 0.1.0:
1804 ======================================================================
1805
1806 This is the initial version of "Das U-Boot", the Universal Boot Loader.
1807
1808 It is based on version 2.0.0 (the "Halloween Release") of PPCBoot.
1809 For information about the history of the project please see the
1810 PPCBoot project page at http://sourceforge.net/projects/ppcboot
1811
1812 ======================================================================